Search Documents

By S. I. Vobnout, J. Wm. White, J. P. Olson

"Mine management now recognizes the value of computer-based truck-shovel dispatching in open pit mines. The key tangible benefits are substantial productivity increases with a given fleet of equipment or, alternately, significant reductions in equipment required to meet production quotas. In this paper, the authors review the literature, report on efficient, optimal algorithms for haul truck dispatching in real-time, and briefly discuss methods used by various mines to evaluate productivity improvements over manual methods. Actual results obtained at thirteen mining operations around the world are also presented.IntroductionModular Mining Systems manufactures, installs, and supports its computer-based DISPATCH system at mines worldwide. DISPATCH is a large scale, computer-based mine management system which controls the dispatching of all haul trucks in any open pit mine (Fig. 1). When increased production is important, DISPATCH gets the needed production increase with fewer new or recommissioned trucks. DISPATCH also helps operations meet its blending objectives while minimizing rehandle and maintaining production. Furthermore, DISPATCH includes a powerful, eventdriven simulation subsystem. With the simulator mine management can pose ""what if' situations and see the predicted effect on production"

Jan 1, 1993

By Julian Baldry

"This paper begins by describing the parameters of high-speed underground tracked drifting operations and the mucking cycle, and-discusses their variations. The railbound Haggloader 8HR is then described, as well as the Hagglund shuttle trains, outlining the advantages and disadvantages of the system. A comparison with conventional mucking operations is then given.IntroductionDrift and tunnel rounds are mucked by one of two major methods, either trackless with diesel loaders and trucks or with track loaders and cars. The aim of this paper is to compare the conventional tracked mucking cycle with the Hagglunds system alternatives.For many years, the traditional method of attacking the mucking cycle has been with a rocker shovel loader, a string of cars and a locomotive. The rocker shovel loads the first car and when full it is taken to a side drift, cherry picker or some other transfer point and is exchanged for an empty one. This empty car is then pushed back into the face and the loading continues until all cars are full . Then the whole train is taken out to a dump point where the cars are emptied. Normally the train's capacity is less than the volume of the muckpile, so the cars go back to the face. This loading cycle is repeated until all muck is removed from the heading. The last train out from the heading usually takes the loader and parks it in a side drift before continuing on to the dump where the cars are emptied.This simplified version of the traditional loading cycle excludes the ancillary work elements such as track laying and so on, but does point out that the cars must be transferred when full and that the whole train normally makes at least two round trips from the dump to the face. The prime aim in drifting is to cycle a round whithin a working shift which necessitates that no one part absorbs so much time as to prevent the completion of the cycle.Mucking, drilling and loading and the ancillary work such as rock bolting, vent and service pipe hanging typically each take one-third of the available work time. Drilling or mucking can and often do, because of various factors, take nearly half of the total cycle time. Once any segment of the operation starts to take this portion of the shift, the likelihood of missed rounds becomes increasingly greater."

Jan 1, 1981

By I. R. Muirhead

"One approach to making new technology available is to demonstrate its value under full-scale operating conditions. Studies were undertaken to assess the feasibility of this approach to introducing a longwall mining system to the western Canadian coalfields.The longwall method of mining coal is described, world and Canadian usage is reviewed, and the merits of the system in comparison 10 other coal mining methods are discussed.The rationale for a longwall demonstration in western Canada is presented, along with a proposed organization for the design, operation and dissemination of the findings from such a trial. The factors which must be considered in the design of the demonstration, and in the assessment of a potential site are highlighted. It is concluded that a demonstration of this technology is both timely and essential to prepare the way for the western Canadian coal industry of future prospects for coal.IntroductionFor many years CANMET has encouraged research work organized on a cooperative basis. This requires that a working consensus must be negotiated by researchers and operators at the beginning of the project and continuously refined as work proceeds. The result is usually a more relevant selection of research problems, improved direct ion and con duct of experiment al work and often a validation phase in which research concepts are tested in an opera ting environment. All this tends to narrow the gap between obtaining research results and applying them.Even under the best of circumstances cooperative projects require a good deal of coordination and enthusiasm to maintain focus and the pace of work. The working perspective of a research scientist in a government laboratory is substantially different from that of a mine operator at a producing mine, and a common ground must be found. This is difficult to do and cooperative projects typically evolve over several years as experimental results progressively define the potential solutions to mining problems."

Jan 1, 1985

By E. Ozberk, N. Gibson, W. G. Davenport

"In the 1950s, Canada produced more than ninety-five percent of the non-communist world's nickel and achieved dominance in terms of production, technology and pricing policies.Over the past thirty years there have been dramatic changes in the nickel industry to the extent that Canadian production is now less than thirty per cent of the total.In this document we have presented statistics relevant to this transformation and reviewed the technology, particularly with regards to energy and environmental considerations.Under the new market conditions nickel producers are likely to face more difficult competition than they have encountered in the past.The economic scene and measured nickel reserves dictate that for the purpose of increasing production, new nickel smelters will not be built in Canada in the foreseeable future. However, in order to reduce sulphur dioxide emissions, Canadian nickel smelters will possibly go through some modifications or rebuilding.IntroductionThis paper presents a review of the Canadian nickel industry in relation to the world nickel industry. Major changes are described which have occurred in the characteristics of the nickel market over the last thirty years. The pre sent status of the nickel market with respect to Forecasting future trends is reviewed and attempts are made to predict what further changes will take place in the next two decades. Comparisons are made of the economics of producing nickel from sulphide ores and oxide ores and the advantages and disadvantages the Canadian nickel producers face.A brief critique of the existing and emerging nickel production technologies in Canada and the world is carried out and attempts are mad e to predict the changes which may take place in the foreseeable future."

Jan 1, 1983

By David A. Grieve, David E. Pearson

"A rank-map of Crowsnest coalfield, showing the distribution of the bituminous coal measures and the locations of major structures, has been produced from vitrinite reflectance measurements on over600coal samples. The timing of coalification in relation to these major structures has also been determined.In the west-central portion of the coalfield a complete stratigraphic succession of coal measures which rides on major thrust surf aces is all of high-volatile bituminous rank, but despite the structural discordance no break in rank is discernible across these structures. The thrust faults therefore predate much of the coalification.Three major valleys expose cross sections of the folded coal measures and in each an increase invitrinite reflectance is demonstrable as individual seams are traced from ridge crest to valley floor. Thus, in these sections, a significant amount of coalification post-dates folding. The proportion of this post-folding coalification is found to increase toward the south of the coalfield.A late gravity-fault, exposed along the east crop of the coalfield, places high-volatile coal-bearing successions in contact with low-volatile coal and demonstrably is a reactivated thrust fault. Coalification at this locality occurred between these two different ages of faulting.The variations in rank and the subtleties of the coalification pattern have, together with systematic changes in the maceral composition of coal seams, had a profound effect on coal quality in the coalfield. Coking coals with a variety of properties occur together with some coals that have no caking capacity."

Jan 1, 1985

By A. McIntyre, L. R. Plitt

Both the Bond and the Hardgrove grindability tests are widely used in the mineral industry to measure the ease of the comminution displayed by a material. The Hardgrove test is mainly used for coals, whereas the Bond grindabifity test is mainly applied to hardrock minerals. The Bond grindability has the advantage that it can be empirically related to the energy required for comminution (work index), whereas the Hardgrove grindabifity test has the advantage of being easier to perform. In an effort to establish a valid correlation between work index and Hardgrove grindability, a series of parallel grindability tests were carried out on a wide variety of rocks and minerals. The standard Hardgrove test was modified to allow for materials with a higher density than coal. A new, satisfactory relationship was established which permits rapid estimation of work index from Hardgrove test data.

Jan 1, 1980

By P .. D. Vaillancourt, D. F. Sangster

Several occurrences of disseminated galena, including a former producing mine, are found in Pennsylvanian fluviatile sandstone of the Salmon River Basin, Cape Breton Island, Nova Scotia. Detailed study of the distribution of these occurrences has revealed that highest galena concentrations are found in sandstone overlying channel-shaped depressions in felsic basement rocks. These buried depressions, in turn, correlate in position with modern streams in areas of basement exposure. This correspondence suggests that the latter are at least partially controlled by an exhumed Pennsylvanian topography. If this is correct, then several other streams in the area, lying on basement, may be used to locate possible undiscovered lead deposits in sandstones of the Salmon River Basin.

Jan 1, 1990

By G. J. Simandl, H. -L. Jacob, S. Paradis, G. Valiquette

"Nos travaux de terrain dans le Grenville, effectués dans le cadre d'un projet d'inventaire des gîtes de wollastonite, ont démontré qu'il existe un secteur exceptionnellement favorable à l’exploration pour la wollastonite. Ce secteur s'étend de la municipalité de Grenville jusqu'au pare du Mont-Tremblant (nord de St-Jovite). D'autres secteurs favorables a 'exploration pour la wollastonite ont été délimités dans les regions du Lac-Saint-Jean, de Shawinigan et de la Gatineau. Neuf categories litho-structurales de gites de wollastonite furent identifiées. L'importance d'un système ou vert pour la formation des gîtes de hautes teneurs fut établie. Un guide de prospection pour la wollastonite propre à la province tectonique de Grenville fut développé. Plusieurs des indices sont prometteurs et mériteraient des travaux de raise en valeur afin de determiner s'ils représentent une source de wollastonite exploitable à profit. Lac-Saint-Jean, Shawinigan and Gatineau areas. Deposits may be classified into nine categories depending on their relationship to intrusive rocks, discordant or concordant contacts with the host rocks, morphology, and major structural controls. Deposits consist mainly of wollastonite, calcite and clinopyroxene. They may contain one or several of the following minerals: feldspar, scapolite, quartz, titanite sulphides, zoisite, clinozoisite, garnet, idocrase and prehnite. Wollastonite content may reach over 70%. Some deposits are associated with graphite veins. Better understanding of the geology, combined with the proposed classification provides new exploration guide for wollastonite. Several deposits have grades of economic interest. Further work is needed to determine if any of these deposits can be exploited for profit."

Jan 1, 1990

By A. J. Hyett, R. D. Reichert

"A laboratory and field research program was conducted to investigate the major factors influencing bond capacity of grouted cable bolts. The results indicate that cable bolt capacity most critically depends on the grout uniaxial compressive strength (UCS), the radial confinement, and the embedment length.In the laboratory &apos;split-pipe&apos; tests were conducted using P VC, aluminum and steel pipes to provide radial confinement, and field test sites were chosen in granite, limestone and shale rock masses. For both datasets higher capacities were obtained under conditions of higher radial confinement. A correlation between the two was obtained through a comparison of the radial wall stiffness of the laboratory pipes with that of the field boreholes as measured using a high pressure dilatometer. Cable bolt capacity was found to increase with embedment length though not in direct proportionality.The use of low water cement ratio grouts (<0.40) can increase cable bolt capacities by 50% to 75%. This effect is maximized under conditions of high radial confinement. However, the use of super thick grout paste (0.30 and less) may be both impractical and undesirable, first because of their limited pumpability and second because of their inconsistency in strength. Grouts with a water cement ratio of between 0.35 and 0.40 are recommended for practical cable bolt applications."

Jan 1, 1992

By O. E. Humeniuk, A. I. A. Salama, M. W. Mikhail

"The Western Research Centre (WRC) of CANMET operate a unique pilot plant facility where ongoing R&D on coal preparation and mineral processing is conducted. The pilot plant carries out two functions: coal preparation processing using state-of-the art technology and coal-liquid mixture preparation with intensive cleaning circuits that can also be used for mineral processing. In total, the pilot plant includes more than 30 different flowsheet options. The facility is dedicated to small and fine coal, and designed to be flexible and versatile.This paper describes the use of a pilot-scale facility as a research tool for process control development, fine coal beneficiation, development of coal-liquid fuels technologies, development of process models and testing and evaluation of new developments. The pilot plant is used to assist in resource development by evaluating and optimizing flowsheet selection, and producing sufficient samples for utilization tests. The facility is also an important tool for evaluating and testing samples from troublesome circuits of operating plants to find means to optimize and improve recovery, particularly of fines circuits.Detailed examples are given to demonstrate the role of a pilot scale facility in coal preparation R&D, coal industry development and optimization of coal processing operations. These examples include the development of heavy-medium cyclone computer control system, detailed evaluation of beneficiation of a coal deposit with high clay content, development of column flotation, and its role in fine cleaning circuits and treatment of ultra-fines in relation to intensive cleaning, the importance of testing coals in different processes, and cleaning processes influence on coking quality and other utilization applications. The potential of the facility for helping the mineral industry is also described."

Jan 1, 1992

By S. Yannacopoulos, L. Bichler, P. Wanjara, J. Gholipour

Characterization of a virgin and in-service Inconel 718 alloy was undertaken to study the changes caused by the service conditions on the grain size, ?? phase, MN-type nitrides and MC-type carbides. The size, distribution and volume fraction of these phases and grain size were studied using scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and electron backscattered diffraction (EBSD) analyses. A considerable difference in the grain size, as well as distribution and volume fraction of the precipitates was observed in the in-service material as compared to the virgin Inconel 718. As a result of these microstructural changes, a notable dissimilarity in hardness between the materials investigated was observed. The results presented in this study are important for proper development of repair parameters and heat treatment of in-service Inconel 718 material.

Jan 1, 2014

By P. Cielo

"Nondestructive inspection is an important quality control tool in the material processing industry. Being nondestructive, such a control may be applied to the whole production, as long as the available techniques are fast and easily automated. Ideally, nondestructive testing (NDT) methods should operate in a noncontact configuration in order to be deployable on-line with minimum perturbation of the production process.After a short introduction to the most common NDT techniques, with particular emphasis on ultrasonic, radiographic and electromagnetic methods, a few new approaches which are under development at the Industrial Materials Research Institute, (Boucherville, Quebec), are reviewed. Noncontact techniques such as laser ultrasound, thermoelastic and thermographic methodologies will be described, and their applications to materials of industrial interest will be discussed."

Jan 1, 1989

By C. Mattich, Å. Holmström, L. Hedström

"The fluidized bed at Division Ministro Hales (DMH) division of Codelco in Calama, Chile is currently the largest operating roaster for partial roasting of arsenic rich copper concentrates. The roaster converts the Mina Ministro Hales (MMH) enargite rich (Cu3AsS4) copper concentrates into calcine with a low arsenic content that is suitable for mixing with other copper concentrates feeding a flash furnace. The plant sets a new standard for the processing of arsenic rich concentrates, both from the quality of the calcine as well as the environmental performances. The process technology and expertise are based on the solid practical experience of treating arsenic rich concentrates from both the Boliden smelter and Outotec.The partial roasting process is located next to the mine and concentrator and includes a sulphuric acid plant with auxiliary equipment. The produced calcine has an arsenic content significantly below target and the residual sulphur meets the requirement of the flash furnace. The plant operates with high efficiency cyclones resulting in a low amount of calcine passing to the hot electrostatic precipitator (HESP). The small flow of HESP calcine dust can be combined with the low arsenic calcine and still meet the flash furnace feed arsenic requirements.SO2 formed during roasting is converted into sulphuric acid, while volatized arsenic is recovered in the wet gas cleaning section of the acid plant along with a large proportion of antimony present in the MMH concentrate. Arsenic is stabilized as calcium arsenate and sent to disposal at a specially prepared site.The present production rate (September/October 2015) is close to or higher than the original maximum design capacity of the plant.INTRODUCTIONMineralogyThe mineralogy of an ore and concentrate is important, since there is a direct link between roasting performance and concentrate mineralogy. The MMH concentrate has a good combination of minerals that makes the roasting process efficient and flexible. The main minerals are pyrite, enargite and chalcocite (Figure 1). The inert content is about 15% and consists mainly of silicate and alumina based minerals. The lead content is very low and this is desirable, since the presence of even a small amount of lead will cause a substantial increase of sintering during roasting."

Jan 1, 2016

By H. D. S. Miller

"This paper introduces a new approach for the design of rib pillars. The approach involves an empirical method for pillar design and a discussion of the pillar stability used for open stope mining methods.The empirical method predicts the degree of stability of rib pillars. Pillar load is estimated using two and three dimensional numerical modelling. Rock strength and the shape effect of pillars are used to account for pillar strength. The method has been calibrated with case histories from Canadian open stope metal mines and is compared with other methods used [or pillar design.INTRODUCTIONThe role of rib pillars in open stope mining is to provide stability to a mining block by limiting rock mass displacements and restricting the exposure of a rock mass in stope backs and stope walls. They also provide flexibility in ore extraction by dividing a stope block into multiple working faces.The use of backfill in open stope mining methods has reduced somewhat the need for optimum pillar design. In contrast to permanent pillar methods, the dimensions do not need to be minimized because the pillars are usually recovered in a later stage of mining. However, the consequences of poor pillar design are often overlooked and can still be severe. A pillar that does not perform its intended role may result in excessive stope or pillar sloughing, difficult and expensive pillar recovery, loss of permanent access and remedial costs such as development rehabilitation, artificial support or low productivity.Pillar design concepts of the past were not developed for open stope mining conditions and generally have not been confirmed for open stoping. The focus of this paper is to introduce an empirical design relationship specifically for open stope pillars. It provides a stable, yielding or failed pillar assessment for a given design."

Jan 1, 1989

By W. J. D. Stone

Discussions with people knowledgeable in the insulating material field revealed that materials on the market would be considerably improved if there was a greater meeting of certain very desirable criteria. Such criteria include: (1) the material should not burn, even at higher temperatures; (2) at an elevated temperature, the material should not give off toxic gases or produce smoke; (3) the material should have a low energy input; and (4) vermin would find the material unattractive. Theoretical discussions led to the conclusion that an insulating material made by foaming a mineral, preferably of a platy nature, with an inorganic binding system that could be converted to a rigid structure at low temperature would likely meet all the above requirements. It was also theorized that the use of microwaves in the converting stage would be beneficial in the creation of a cellular structure by aiding the foamer through creating vacules of steam. Talc was selected as readily meeting the theoretical mineral requirement and the material of Baker Talc Limited was used as the basic filler. The early results obtained led to an agreement between Americ Mines Limited and Baker Talc Limited pertaining to commercial production in a specific geographic area. It was recognized that due to the economics of shipping, the availability of the basic filler material should be geographically widely spread. Samples of materials were requested and many received from all over North America and one from Britain. Enough work has been done to show that they respond to the basic process in a similar manner as the Baker Talc material. From the data acquired, it is considered that the process is applicable for the production of loose fill insulation, moulded insulation for pipes and structural steel, ceiling tile, batts, sheet and for incorporation into other products such as various roofing board materials. Sufficient development has been done to enable a budget to be prepared for the construction and operation of a loose fill insulation plant.

Jan 1, 1979

By R. Frank Chiappetta, E. B. Wilson

"The maintenance records for AL-60 airlegs at Falconbridge Ltd. are used to demonstrate some of the procedures for the analysis of such data.The data are not representative of pure failure s of one type or another. In fact, the records are for the undefined pseudo-failures which are usually found in industrial operations. However, because the machines are brought to the shop only when inoperative, the individual recorded components are treated as failures. Manual calculations are conducted to show the analysis of variance (ANO VA) approach to determine whether certain data can be combined; only a limited number of the 206 machines being considered. The manual procedures continue with the weighting of the suspensions; i.e. terminations f or reasons other than the failure of the given component. After the data are sequenced in the proper order, the nature or pattern of the data is determined using the Kolmogorov-Smirnov (KS) test.It is recognized that these manual examples must be replaced by compute r methods 10 process voluminous data of this nature. Such programs are developed and available. However, a program called RELCODE is used in this case to correspond to the manual examples and to take into account the suspensions. These analytical procedures form the basis for those studies required for good maintenance management."

Jan 1, 1985

By M. A. Upham

"Prairie Evaporites of the Province of Saskatchewan in a deep oil-well hole. Exploitation started in 1950 under a shroud of doubt that this huge reserve could be mined. It was fraught with almost insurmountable physical problems in penetrating the Prairie Evaporites. After 12 years of experimentation and development of new shaft-sinking methods, mining equipment and processes to treat the high-grade potash ore (sylvanite), a new era of high-risk resource development dawned in Saskatchewan.The development of 10 new mines opened up the largest known mineable potash reserves in the world and Canada became the second largest. producer of potash to supply domestic (U.S.A. and Canada) and overseas markets. A monumental program in marketing-devising new transportation systems and strategically locating warehouses-was developed in order to expeditiously service domestic and overseas customers. The year 1969/70 started a period of overcapacity and the problem of prorationing. As the market strengthened in 1974, the Saskatchewan Government applied the reserve tax to the industry. Then, they announced the setting up of a Crown corporation to acquire ownership by purchase of up to fifty per cent of the industry. During this time, potash was discovered in New Brunswick within 50 to 60 miles of a seaport, where two deposits have been explored by the same pioneers who started the potash development in Saskatchewan.With this background, the paper will examine various elements of the economics and marketing of Canadian potash."

Jan 1, 1980

By Grant L. Anderson, Richard C. Rice, Richard L. Jentgen

"Data for underground mine-hoist ropes determined in the Ontario Special Rope Tests were obtained, encoded and analyzed statistically. Prior 10 refined statistical analyses, these data were subjected la characterization studies and preliminary analyses to allow trends to emerge that could be used to guide and facilitate the refined analysis. The data were characterized by determining distribution s for a wide range of variables including remaining strength, service life in terms of lime and hoisting cycles, outer-wire torsion values, elongation during tensile testing, diameter reduction, location of strength loss and the strength lasses associated with corrosion rating and lubrication rating , This paper describes the more important relationships between remaining strength (or, conversely, strength loss) as the dependent variable and some of the principal independent variables mentioned above.IntroductionBoth productivity and safety in underground mines could be improved if mine-heist rope Iife and reliability could be predicted more accurately . As a result, hoist-rope failure processes and their effects on rope life and remaining strength need to be quantified and related in such a way that improved retirement criteria can be developed. This is true whether the failure is incipient or actual or whether the failure mode is by corrosion , wear, fatigue or a combination of these factors."

Jan 1, 1984

By R. C. Lo, M. D. Scott

"This paper reviews tailings management at Highland Valley Copper, and outlines main features of its tailings storage facility enclosed between the H-H and L-L dams. Key management focusses are: energy efficiency, cost effectiveness, safety and integrity of the tailings impoundment, environmental protection, and reclamation after decommissioning. Main features of the tailings facility include: high international standards for seismic and flood design criteria, water management and water quality monitoring, operations and construction optimization, reclamation and decommissioning plan, and geotechnical challenges associated with the complex geology of the L-L tailings dam foundation.IntroductionHighland Valley Copper stores its tailings mainly in the Highland Valley tailings facility (ultimate capacity: 1.8 billion tonnes). Smaller tailings storage facilities were operated by predecessor companies: the Number One Pond, the Trojan Pond at Bethlehem and the Highmont Pond at the Highmont operation as well as backfilling the Heustis and Jersey lona Pits at Bethlehem. These areas are currently not in use, and are in the reclamation phase prior to decommissioning. This paper focusses on tailings management in the main facility. As indicated in Figure I, the facility includes three tailings dams: these are, going from east to west, the H-H, J-J and L-L Dam, named after the alignment alternatives in the initial feasibility studies. From 1970 to 1977 Canadian Bechtel Ltd. advised Highland Valley Copper&apos;s predecessor company Lornex, on tailings storage at the H-H and J-J Dams and on the L-L Dam. Since the completion of the L-L Starter Dam in 1977, Klohn Leonoff Ltd. has provided ongoing consultation and construction monitoring of the raising of the L-L and the H-H Dams. The J-J Dams is currently buried by deposited tailings. This paper reviews key tailings management focusses and main features of the tailings facility."

Jan 1, 1992

"The Pierre Beauchemin Mine attained commercial production in January 1989, and went on to produce 23 968 ounces of gold for the year, 3% higher than forecast. Underground development was accelerated to prepare the way for the production of an estimated 40 000 ounces in 1989.IntroductionThe Pierre Beauchemin Mine is located nine miles west of the city of Rouyn-Noranda (Fig. I).As a result of the amalgamation with Sullivan Mines in October 1987, the mine is now entirely owned by Cambior Inc.The Eldrich deposit was discovered in 1953and began production in 1955, closing in 1962 following the decrease in gold prices and the simultaneous decrease in silica content in the ore, which was sold to the Noranda smelter for flux. A total of 717 000 tons grading 0.14 oz Au/t were produced during this period.From July 1984 to October 1987, an underground exploration program was carried out by Sullivan on the Eldrich mining concession and the nearby Flavel property. The first phase of the program included reinstallation of surface facilities and dewatering of the Eldrich Mine. Following the completion of the first phase, extensive exploration was carried out, including a major program of diamond drilling. It was then decided to deepen the shaft to a depth of 1800 ft to access a new zone called the No.5 Zone .Following the amalgamation with Sullivan in October 1987, Cambior assumed the role of operator for the project, and continued the shaft deepening work that had already been started. A feasibility study was completed in April 1988 and the Cambior board of directors approved a production decision for the Eldrich-Flavel project.The preproduction program extended from May to December 1988 and was aimed at preparing the stopes in the upper part of the mine and at developing the mine infrastructure at the bottom of the mine.The mine was officially opened in August 1988. Cambior renamed the project the Pierre Beauchemin Mine in recognition of Pierre Beauchemin&apos;s pioneer-work."

Jan 1, 1990