Search Documents

By K. C. Corin, Z. G. Song, J. Y. Liu, M. W. Zhang, State Key Laboratory of Mineral Processing-BGRIMM, J. G. Wiese

"In the present study effect of grinding media on flotation of two mineral systems have been investigated, viz. sulphide minerals (including a pure chalcopyrite and pyrite mineral, and two different base metal sulphide ores), and oxide minerals (quartz, hematite and cassiterite). It was shown that mild steel media milling produced lower recoveries in the case of chalcopyrite and pyrite, as compared to the case of milling using ceramic media. For oxide minerals, the effects of using mild steel media as opposed to ceramic media were not as significant as was for the sulphides, although, after mild steel milling, at acidic pHs their recoveries were significantly reduced. For two base metal sulphide ores, viz. Nkomati and Dexing ores, the differences resulting from different milling media , although marginal, were opposite for each of these ores.For oxide minerals XPS showed that oxides and hydroxides of iron (e.g. FeOOH) adsorbed on the surfaces of the minerals. In the case of the Nkomati ore, adding Fe2+ or F3+ ions after milling with chrome steel media resulted in reduced talc (gangue) recovery, but increased water recovery and reduced concentrate grades. Further investigations are currently in progress to examine the Fe ions effect on the talc surfaces and froth properties.INTRODUCTIONGrinding of ores is necessary to liberate the valuable minerals from its gangues to allow for their selective recovery during mineral processing such as flotation. The grinding process inevitably involves contact of the ores with the surface of the grinding device and the grinding media. Accompanied by grinding, several phenomena can occur including the grinding medium wear, formation of precipitated species on the ore surfaces, chemical reaction, galvanic effects, changes in the Eh of solution, etc. There is a considerable body of literature on the differences observed in the flotation of various ores after milling using various grinding media. Laboratory studies have used balls or rods made from mild steel, ceramic, stainless steel or chrome steel to investigate the effects of different grinding media on mineral flotation. It is found that the interactions between the ore and the grinding environment can affect flotation separation of sulphide (Wei and Sandenbergh, 2007; Bruckard, 2011), oxide (He et al., 2014) and carbonate minerals (Song, 2009 and 2010). For example, mild steel milling produces relatively high concentrations of Fe ions in the pulp, affecting the recoveries of minerals compared to the case of ceramic media. On the other hand, the stainless steel media or chrome media are reported to be beneficial to the recovery of sulphides, when compared to the cases of using mild or carbon steel media (Rey and Formanek, 1960; Peng et al., 2003a,b; Huang and Grano, 2006; Bruckard, 2011). It is not clear, however, whether these Fe ions may affect the surface properties of the minerals involved or the general pulp/froth behaviour and hence their floatability. In addition, in the study of an low-S PGE ore carried out by Miettunen et al. (2012), forged media grinding in the CO2 atmosphere led to the highest Pt and Pd grades and recoveries, but the high chrome grinding media gave lower flotation recoveries than those using the forged media."

Jan 1, 2016

By F. N. Smith

The carbon steel casings of Heat Recovery Steam Generators (HRSGs) in a co¬generation plant were found to have developed cracks that originated on the inside surfaces. The HRSGs receive hot exhaust gases from the primary Gas Turbines (GTs), which are fuelled with pipeline natural gas. The GTs was initially operating without any suppression of nitrogen oxides (NOx). After being in service for about two years, some of the cracks were found to have penetrated right through the 1/4 in. thick casings. The casings are fitted with insulation on the inside (hot gas side). Examination of steel samples cut from the casing walls revealed (i) fine cracks propagating through the steel from the inside surfaces, and (ii) the presence of relatively large amounts of nitrate ion on the inside surfaces. It was concluded that the nitrate ions originated from nitric acid that was condensing on the relatively cool walls of the casings behind the insulation. Nitric acid was formed in the GT exhaust gases by the combination of water vapour (formed from combustion of the hydrocarbon fuel and from moisture in the combustion air) and nitrogen oxides (formed from nitrogen and oxygen in the combustion air).

Jan 1, 2005

By Y. Kashiwaya, J. Yagi, P. R. Austin

The problems of global environment and resources have become important issues in recent years, and the iron and steelmaking industry is requested to decrease energy consumption and carbon dioxide emission. The improvement of efficiency of ironmaking system is one of the countermeasures for these problems because more than a half of total energy input to the integrated steelwork is input to the ironmaking system. Various approaches to improve the blast furnace process have been made. The authors examined their performances through mathematical simulations of blast furnace operation, and confirmed the improvement of blast furnace efficiency under some operating conditions. The ironmaking system consists of various processes, and the materials and the energy are transported among these processes. Thus it is necessary to evaluate the efficiency of the novel operation of blast furnace based on the ironmaking system. In this study, the balances of material and energy on ironmaking system that consists of blast furnace, coke oven, sintering and hot stove processes were analyzed. The operation status of each process in the system was adjusted according to the results of the operation simulation of the blast furnace under novel operating conditions. The analysis clarified the effect of the blast furnace operation on the energy balance and CO2 emission of the ironmaking system.

Jan 1, 2015

By K. Sasaki

Ventilation measurements were carried out in a shallow underground-quarry space with relatively large internal volume of 14,600 m3 in order to evaluate its effective ventilation characteristics. Based on air velocity measurements with an ultrasonic anemometer in the exhaust airway connected to the space, it was found that the space was ventilated by natural ventilation airflow with intermittent changes in direction. It was difficult to measure the ventilation flow with typical methods of flow measurement provided from the intake portal and throughout the mine, because the cross-sectional area and volume of the openings were too large and the flow was variable. In the present study, a tracer gas method was applied to evaluate the effective ventilation airflow rate in the space. A photo-acoustic infra-red gas monitor, highly sensitive to SF6 gas used as a tracer gas, was set in the space to determine air exchange rates from gas concentration-time decay curves. The seasonal variations of airflow and thermal environment in the space were investigated through 13 sets of measurements taken over 15 months. Airborne rock dust concentrations were also measured at same time in the opening. The correlations between the effective ventilation airflow rate, thermal environment and dust concentrations in the opening space were analyzed and are discussed based on the presented measurements taken during year. It is concluded that seasonal variations in effective ventilation flow and the dust concentration are mainly due to differences in air temperature in the space, as affected by the rock?s surface temperature and atmospheric temperature. In summertime, the air temperature and associated air density difference generated lower natural ventilation flows resulting in higher dust concentrations.

Aug 1, 2013

By R. O. Loutfy, J. C. Withers

"Titanium powder is produced from a small fraction of sieved sponge, HDH of sponge or gas blown from a melt produced billet. Ore from foreign sources is chlorinated in a very high temperature fluid bed to make TiCl4, then vacuum distilled purified and then reduced to sponge by Kroll processing. Domestic ores of ilmenite or perovskite can be carbothermically reduced to Ti2OC which can be chlorinated at low temperatures of 250–400°C to produce TiCl4 which can be electrolyzed in a fused salt to Ti powder, or the Ti2OC used as an anode in electrolysis to produce Ti powder. The electrolysis process can be operated continuously to produce Ti powder at a lower cost than Kroll processed sponge including produce control size powder. Electrolysis processing was scaled up and operated at the commercial demonstration stage on a continued basis that verifies the potential of a low cost process to produce Ti powder.INTRODUCTIONTitanium and alloys of titanium powder have been elevated to strategic status resulting from a focus of producing meltless titanium components as well as a feed for additive manufacturing processing. However, the high cost of titanium powder has limited wide scale implementation of using titanium powder as a feed to any process to produce titanium components. Titanium powder free of alloying is available as sponge fines from the Kroll process as illustrated in Figure 1. Titanium alloy powder is much more expensive, also illustrated in Figure 1 produced from an alloy ingot or mil product as the feed and then transformed into powder by one of several melt form processes which accounts for the high cost of titanium alloy powder at approximately $60–150/lb. Ton lots of titanium alloy powder (i.e. Ti-6Al-4V) from one source is quoted at $120/lb. in the U.S. It appears that alloy powder production cost by current processing is not sensitive to volume."

Jan 1, 2016

By D. N. Madge

The use and development of industrial process control computers in the mineral industry during the 1970's has been sluggish. This cautious approach is due to lack of commitment by senior management. The lack of commitment is due to several reasons: variable mineral processes and technologies, market fluctuations, and excessive costs and inadequacies of applicable products supplied by computer vendors.

Jan 1, 1979

By P. Hickey, G. Hubert, P. Healy

"J. S. Redpath Limited, an underground contractor with a worldwide presence, has implemented innovative techniques in various projects in Canada to shorten the development cycle. Conventional methods currently used for installing primary ground support are compared with the Australian technique of bolting and meshing with jumbos equipped with twin telescopic booms, in-cycle shotcreting, and the use of two jumbos and two scissor bolters set up side by side in wide headings. Recommendations and lessons learned are presented with the aim of providing realistic expectations with regard to development advance rates in a mining environment.RÉSUMÉ J. S. Redpath Limitée, un entrepreneur minier souterrain d’envergure mondiale, a complété plusieurs projets au Canada où des techniques novatrices ont été mises en oeuvre pour raccourcir le cycle de développement. Cet article présente une comparaison entre les méthodes conventionnelles fréquemment utilisées pour le support de terrain, la technique australienne de boulonnage et d’installation de grillage au moyen de jumbos équipés de flèches télescopiques doubles, du béton projeté appliqué durant le cycle de développement et de l’utilisation de deux jumbos et deux boulonneuses côtes-à-côtes dans des galeries de grandes dimensions. Les recommandations et les leçons apprises sont présentées dans le but de fournir au lecteur des attentes réalistes quant aux taux d’avancement du développement dans un environnement minier."

Jan 1, 2016

By R. Walker

This paper deals with the selection and design of a belt conveyor handling steam coal between a mine and a barge loading terminal, and extending for some 5 ¼ miles over some of the most rugged terrain in the state of West Virginia, U.S.A. After a thorough analysis by consulting engineers and the owner's engineers, a single-flight cablebelt conveyor was chosen as representing the alternative of greatest reliability and lowest over-all cost. The value analysis and design features of the system are covered in this paper along with an updated report on the performance of the system since its start-up in the spring of 1969.

Jan 1, 1971

By Glenn Davis

In the world of large scale open pit mining, the majority of a mines operating cost is tied to the removal and transportation of the overburden waste material. Typically, many large haul trucks are employed to transport this overburden from each excavating face. The trucks transfer the waste material from deep within the pit to waste dumps on the surface incurring significant costs in operators, road construction and maintenance, vehicle maintenance staff and support facilities, fuel, tires, and spare parts, as well as the capital cost of the truck fleet itself. In addition, the haulage of the actual mined material carries similar operational costs. In both cases, these costs grow as the mine face advances and pit haulage distances increase. Reducing truck haulage is one key to the success of the Dual Truck Mobile Sizer (DTMS). Being the world?s first fully mobile truck dump station, transportation costs can be significantly reduced as the mine face advances. Furthermore, when used in conjunction with a shiftable face conveyor and a mobile overland hopper, substantial cost savings can be achieved. The mobility of the system allows for the considerable reduction in the haul truck fleet. Overall mine site emissions levels are greatly reduced by the fleet elimination, as well as keeping the majority of the hauls on a flat grade within the pit. Emission levels on a typical truck will dramatically spike as the angle and the length of the haul are increased. Moreover, comparing diesel engines versus electric powered conveyors to move the material contributes to the realized savings.

May 1, 2010

By Olav Mejia

The rising energy costs and environmental considerations in mining necessitate the development of energy-efficient copper and gold processing plants. This paper presents an analysis of technical strategies aimed at reducing energy consumption in these plants. Key approaches include the integration of advanced ore sorting technologies, High Pressure Grinding Rolls (HPGR), Coarse Particle Flotation (CPF), and high-intensity flotation. Ore sorting enables early-stage waste removal, reducing the downstream processing load and associated energy use. HPGR technology, recognized for its energy efficiency, contributes to significant energy savings in comminution circuits by reducing reliance on traditional grinding methods. CPF technology further optimizes flotation performance by enabling the recovery of larger particles, thereby decreasing the need for fine grinding and reducing overall power demand. High-intensity flotation units enhance separation efficiency and mineral recovery in a compact footprint, offering further reductions in energy consumption. Together, these technologies provide energy saving opportunities to achieve a more sustainable and economically viable processing operation. This paper evaluates the effectiveness of each method, highlighting their potential impacts on energy consumption, operational efficiency, and cost-effectiveness in copper and gold processing

May 4, 2025

By J. H. Walsh

IN THE DEVELOPMENT of procedures for the separation of minerals, the choice of reagents for flotation is frequently determined by the extent to which a given mineral is wettable by water. Measurements of the contact angle of an air bubble on wet mineral surfaces are often used in the laboratory to estimate the wettability of the surface. For the results of these measurements to be reproducible, the surface of the mineral must be polished to a mirror-like smoothness and must be free from oily contamination. Elaborate procedures for preparing mineral surfaces have been developed by Wark ( 1) and Taggart (2), and these procedures have been generally accepted as adequate for their purpose. The polishing techniques, how-ever, have certain inherent disadvantages which make it impossible to assess the effects of polishing, entrained abrasive, and adsorbed gases on the wettability of the mineral surface.

Jan 1, 1957

By Ltd Changsha Research Institute of Mining and Metallurgy Co., Shi Yunliang, Luo Yunbo, Chen Jun, Liu Miaohua, Xiao Jinxiong, Long Yan

"A refractory lead-zinc oxide ore located in Yunnan has hundreds of tons of metal reserves, which is hard to be recovered effectively by conventional oxide ore beneficiation methods. In this study, by sulfidation roasting of raw-ore, sulfide deposit is formed on the surface of the lead-zinc oxide ore, and then the roasted ore is processed with bulk flotation. The test results indicate that a bulk concentrate with grade of 7.85% lead and 34.24% zinc, recovery of 79.13% lead and 79.04% zinc, respectively, can be obtained by using conventional sulfide ore flotation method.The sulfidation process shows that pyrite in the raw ore releases S firstly, then S reacts with PbO and ZnO to transform into PbS and ZnS. When the mole ratio of sulphur:zinc is 0.59, the surface of smithsonite is covered with a layer of zinc sulfide. When the mole ratio of sulfu:zinc rate is 1.47, entire simthsonite particle is transformed into zinc sulphide. Thus the transformed particles can be recovered by flotation without complete sulfidation.INTRODUCTIONWith the increasing demand for zinc and decreasing of zinc resources, people pay more attention on development and utilization of zinc oxide ore. However, zinc oxide ore has wide range mineral kinds, complex mineral composition, disseminated fine-grained particle size, and high content soluble salt, so current study results about the zinc oxide ore with conventional flotation are not satisfactory. So far, process dealing with zinc oxide ore includes: sulfuration (Na2S)-flotation, direct flotation with fatty acids collectors, metallurgical methods, in which sulfuration flotation is the most widely used method. The basic principle of sulfuration flotation method is firstly roasting oxide ore with vulcanizing agent, and then recovering the sulfurated oxide ore with flotation, which is similar with recovering nature sulfide ore by using conventional collectors such as amines and xanthate."

Jan 1, 2016

By M. Dosoudil

"Continuous pressure filtration is a modern process for the mechanical dewatering of flotation concentrates of coal and similar coal slurries. This method will give a lower moisture content than classical vacuum filtration, the improvement lying in the range 5% to 15%. Eighteen coal slurries have been examined in this survey. They are representative of a wide spectrum of filtered slurries. IntroductionDuring the last five years, a number of coal slurries have been tested either in the laboratory or with a pilot plant. The test pressure ranged from one to six bar. The results have been evaluated by mean s of a computer. Determination of the filter capacity and the resulting moisture content and energy consumption has been made with respect to the continuous pressure filter, Amafilter construction-type KDF (Fig. I) . Standard sizes of these filters are 60 m2, 90 m2 and 120 m2.The continuous pressure filter is a horizontal filter with a level tank. Six filter axles are mounted on a rotating main shaft, each with a particular number of elements attached. The elements rotate on their axes and move along a circular trajectory. Periodically the elements submerge into and emerge out of the slurry. A constant air pressure is maintained above the suspension, thus providing the pressure gradient necessary for filtration. The filtrate together with the dewatering air flows through the elements into the hollow axle and out of the filter."

Jan 1, 1987

By P. R. La Pointe, J. Clark

"Studies have shown that the roof in coal mines is nearly twice as likely to fail at intersections as at entries due to enlarged roof spans, stress redistribution and other factors. However, the relative stability of intersections in a mine varies, and an improved understanding of what factors impact roof instability can lead to efficient, proactive mining practices that both enhance stability and mining efficiency.A study was undertaken at an underground longwall coal mine to develop a model to predict the stability at the intersections of entries and cross-cuts. The statistical analyses relied upon observational and measured data regarding the development of tension cracks, seepage, intersection geometry, mining practices, geological attributes and geomechanical factors at 783 intersections. Each intersection was given a NIOSH roof. Common data mining techniques, such as multivariate linear regression, multinomial logistic regression, decision trees and probabilistic neural nets, were considered and evaluated to establish correlations and associations between stability and the other variables. Two of the more successful techniques were Decision Trees and Multinomial Logistic Regression. The analyses showed that a number of factors impacted stability:• Overburden thickness (impact on stress concentration magnitudes)• Initial opening area (impact on stress concentration magnitudes)• Sulfur content (depositional environment & impact of mechanical properties, leaching effects)• Intersection type (impact on stress concentrations)• Gob distance (impact on stress concentrations)• Presence or proximity of a particular sandstone (impact on mechanical properties)• Roof bolt type and diameter (impact on reinforcement)Some factors showed no statistically significant relation to stability. These included:• Total area• Supported areaSeepage was a more problematic variable in assess. Seepage is associated with instability, but it is not clear whether seepage occurs as a consequence of instability, for example, through the creation of tension cracks, or whether the intersection has been excavated where water already exists and has degraded the rock prior to excavation, leading to greater instability.Seepage appears related to the geology of the roof rock mudstones, not the sandstones. Tension cracks in the intersections occur preferentially where the Sulfur content is below 0.9%. The Sulfur may relate to mechanical differences in the roof rock, and where the Sulfur is low, the roof is less stable, there are more tension cracks, and seepage is greater. This suggests that the weaker mudstones may be more prone the development of tension cracks, not because these rocks are more brittle, but possibly weaker.2-way and 3-way intersections appear to have less seepage than 4-way, although very few intersections overall have any seepage. This is similar to the roof stability, in which the 2-way and 3-way are more stable. 2-way and 3-way intersections have fewer-than-expected tension cracks, while 4-way have more than expected. These results suggest that four-way intersections are weaker and more prone to tension crack development, also suggesting that increased seepage results from weaker roof conditions, rather than the converse. Thus seepage appears to be mostly a consequence of instability rather than a cause and is higher where there are 4-way intersections, mudstone geology and external loading factors like depth of cover and proximity to gob that promotes crack development. The study also indicated that a better understanding of the mudrock facies could reduce uncertainty."

Jan 1, 2015

By C. S. Ha, H. S. Choi, D. Y. Shin

POSCO installed a new 100 ton oxygen bottom-blown converter in 2013 for the development of new steelmaking process named as PS-BOP which is reading POSCO-Saarstahl Basic Oxygen Process. This process was developed by the collaboration research between POSCO and Saarstahl AG in Germany that is based on substantial increase of CO post combustion in a converter by blowing hot air from the top of converter. The collaboration research has been finished successfully in November 2013 with 17% decrease in hot metal ratio (HMR) when hot air was blown from the top of the oxygen bottom-blown converter. After the collaboration research the converter has been tried to be operated as oxygen top and bottom-blown converter to reduce bottom wear and to decrease production cost with increased use of low cost Fe source by the help of increased CO post combustion. The presentation includes experience on the start up of oxygen bottom-blown converter, HMR reduction trials with hot air top blowing and transition from oxygen bottom-blown to top and bottom-blown converter operation.

Jan 1, 2015

By F. Liu, H. A. Meier, D. M. Valiveti, P. A. Gordon

Hydraulic fracture is a frequently used technique in the Oil and Gas industry to create high permeability pathways for extraction of hydrocarbons. Numerical simulation of this method poses challenges such as representation of 3D fractures, propagation of randomly oriented fractures in 3D media, enabling fluid leak-off from fracture to poro-elastic medium. We have developed a numerical model using the Generalized Finite Element Method (GFEM) to simulate fluid driven fracture in a poro-elastic medium that addresses these challenges. In the GFEM framework, special enrichment functions are used to augment the solution space in the displacement and pore-pressure fields in order to accurately capture the response in the vicinity of the fracture. Adaptive refinement of the finite element mesh is also employed to facilitate accurate and efficient solution of the model. Our model fully couples fluid flow in the fracture, represented with the lubrication approximation, to the geo-mechanical behavior of the bulk poroelastic rock, comprised of an elastic rock skeleton saturated with fluid. Fracturing fluid exerts traction on the fracture surface and is also allowed to leak-off into the poroelastic medium using a transfer function approach. Stress intensity factors (SIFs) are evaluated based on the Contour Integral Method, accounting for the fluid pressure on the fracture surface. The SIFs are used to govern a full 3-D evolution of the fracture. Verification of the model is performed for known behaviors for the poroelastic response and fluid flow in the fracture.

Jan 1, 2015

By A. Hayatdavoudi, D. Chitila, F. Boukadi

"Shale oil and gas have provided a tremendous boost to energy production in the United States even though the characteristics and behavior of shale are yet to be fully understood. Hydraulic fracturing is often applied to horizontal shale wells to stimulate production. This experiment seeks to determine effects of cyclic variable temperature, water vapor and exposure time on shale micro fracture propagation. We used 22 small Pierre shale specimens and subjected them to aforementioned conditions. Fractures developed in 19 specimens. Combination of high temperature and high water vapor generated the largest number of micro fractures on the specimen surfaces.INTRODUCTIONShale oil and gas have contributed immensely to energy independence in the United States. Most if not all shales depending on their total organic content (TOC) and their clay content bear the promise of being a source rock. For example, the Eagle Ford shale play, located in south Texas, is one of the key contributors to the recent rise in oil and gas production in the United States. Data from the U.S. Energy Information Administration (EIA), published in 2014, states that monthly oil production from Eagle Ford wells increased from 340 barrels per day (bbl/d) in January 2009 to nearly 1 million bbl/d in June 2013. Natural gas production has also increased at a similar rate over the same period, from 5.8 million cubic feet per day (MMcf/d) to nearly 4,000 MMcf/d (EIA, 2014).According to the railroad commission of Texas (RRC) 2014 published information, the Eagle Ford shale play is an important play because it produces gas and more oil than other shale plays in the United States. It is an organic-rich play with carbonate shale percentage in the 70% range in south Texas and the shale content increases moving to the northwest. High carbonate proportion renders this play brittle and suitable for hydraulic fracturing treatments."

Jan 1, 2015

By K. Soucek, J. Ptácek, A. Hastíková, R. Kukutsch, P. Konícek, P. Waclawik

"Cable bolts are used frequently as a secondary support system (with steel arch support) in difficult stress-strain conditions of deep coal mines. The load transfer mechanism of cable bolts depends on several factors, such as the strength, deformation and geometric properties of the bolts, resin and the surrounding rock mass so-called cable-resin-rock system (CRR system). The bonding length and bolt/borehole diameter ratio strongly influence the final bearing capacity of the CRR system.The study presents the behaviour of CRR system during a pull-out test which is usually used in the carboniferous rock mass in the Czech part of the Upper Silesian Coal Basin. A series of 28 pull out tests were performed on 3-m-long cable bolts, with various combinations of borehole diameters and bonding lengths, to understand this behaviour. Boreholes were drilled into a solid rock mass consisting of fine-grained sandstone to guarantee similar conditions during the pull-out tests. Video inspection and measurement of borehole diameters were performed to determine their quality and real diameters. Three characteristics were observed from pull-out test results: ultimate pull-out load; displacement of the end of bolt and system stiffness. Numerical modelling by FEM (Finite Element Method) was used to determine the stiffness of the CRR system for variable bolt/borehole ratios and bonding lengths each under constant load. A linear elasto-plastic model and a mohr-coulomb model were used for cable and resin-rock respectively. The results of the experiment may contribute significantly to improving of the methodology of cable bolts installation as well as the design of used cable bolts."

Jan 1, 2015

By J. H. Sokolowski, R. I. MacKay

The level of Si and Cu in the 3xx series of alloys affects the volume fraction of the a-Al dendritic phase and the Al-Si eutectic phase. The volume fraction of these phases in turn affects the feeding conditions during solidification and ultimately the Area Fraction Porosity and Mean Pore Diameter measured in the as-cast structure. This work sets out to establish the relationship between the volume fraction of the a-Al dendritic phase and the Al-Si eutectic phase and the resulting porosity that forms on the Monotonic and High Cycle Fatigue properties. The alloys in question are the Al-9%Si-l %Cu and a Al-7%Si-4%Cu alloys which were cast into V8 performance engine block castings and then heat treated to achieve desired mechanical properties. The engine block castings provided the mechanical and metallographic test samples analyzed for this work.

Jan 1, 2006

By Paul Guliov

Potash dominates the industrial mineral scene in Saskatchewan accounting for 44% of total provincial mineral production in 1981. More than 7 million tonnes of potash have been produced annualy in recent years; ten underground mines are presently (1983) active. Sodium sulphate and cement are also important mineral products. Construction aggregates, clay products, bentonite, salt, peat moss and sulphur complete the list of industrial mineral products.

Jan 1, 1984