Search Documents

By Noel Brien, O&apos

General: National Asbestos Mines Limited has operated an asbestos mine and mill near Thetford Mines, Quebec, since 1958. As a result of additional exploration of the orebody in 1962-63, it became apparent that long-range mining plans would have to be revised to allow for a large increase in both ore and waste tonnages. It was decided that the task of checking out possible mine designs could best be analyzed by a computer to obtain data from which an optimum open-pit configuration could be plotted. Object: It was desired to arrive at an optimum open-pit configuration with an over-all pit slope of 45 degrees and a minimum operational width of 200 ft. at the bottom. Calculations were based on assay values from diamond drill holes in cross sections of the mine. The computer's assignment was to select and describe, by coordinates, the optimum cross section for the mine. Mine engineers then assembled the various optimum sections to produce the pit outline. As this would not necessarily result in a practical mining arrangement, the computer also provided alternate solutions,

Jan 1, 1965

By F. A. McLean

Given a promising claim and the required financial backing to develop it, the first problem that confronts the mine operator is usually the selection of the necessary compressed air plant. The size and type of drive are questions that naturally follow, the former being determined largely by the amount of money available and the speed with which it is desired to carry on the programme of development. The type of drive, such as electric motor, steam or oil-engine, depends on local conditions and has an important bearing on the cost of operations. ns. Few prospective mine operators are fortunate enough to locate claims within the service radius of electric power-lines, although this is more likely to happen nowadays than formerly. In the majority of cases, however, some other form of prime mover is necessary. When wood or coal are available at moderate cost, a small steam-driven plant is usually chosen. Such plants are often arranged so that they can be converted to electric-drive should future developments at any time make this desirable. Many plants of this type are installed in northern Ontario mines. When wood or coal are costly or difficult to transport, oil-engine driven mining plants have many advantages in their favor, and are now quite commonly used. Oil in some locali-ties is considerably cheaper than wood or coal, and is much easier to transport over bad roads.

Jan 1, 1924

By A. F. Matheson

The St. John Del Rey Mining Company, Limited, is an English company owning 150 square miles -of mining lands near Belo Horizonte, Minas Geraes, Brazil. The area is 2,300 to 5,000 feet above sea level, with a pleasant and healthy climate. Bedrock is Precambrian. The Nova Lima series of metamorphosed sediments and some volcanics is overlain uncomfortably by the Minas series of quartzites, itabirites. etc. Batholithic granite and gneiss cut both series and basic dykes cut all these rocks. There are important deposits of gold, iron, and manganese on the Company's holdings, as well as occurrences of arsenic, antimony, cobalt, nickel, dolomite, day, quartz, -ochre, bauxite, kyanite, and asbestos. Except for gold and consequent recovery of arsenic, all the other materials are relatively unexploited. The Company operates the Morro Velho gold mine and the Espirito Santo and Raposos gold mine. The Morro Velho mine was purchased in 1834 for £56,000. To the end of 1952 it had produced 7,000,000 troy ounces of gold from 15,000,000 short tons of ore. The ore z?ones are replacement deposits in a sinuous siliceous dolomitic rock locally termed "lapa seca," and plunge east, near surface at 45 °, at 8,000 feet at 15°. The ore minerals are pyrrhotite, arsenopyrite, pyrite, and chalcopyrite. Gold is finely distributed and almost nowhere visible. Ore reserves at the end of 1952 were estimated at 5.5 million short tons grading 0.39 oz. gold per ton. Chances exist for new ore within the mine area. The Espirito Santo and Reposos mine, in folded banded iron formation, has mineralization similar to Morro Velho but sulphides are less abundant. The mine to a depth of 2,500 feet has estimated ore reserves of 1.5 million tons of an average grade of 0.28 oz. gold per ton. New ore may be expected both laterally and at depth. To the end -of 1952, the ?Company had paid dividends of almost £4,- 600,000, largely earned from the operation of the gold mines.

Jan 1, 1956

By Patrick E. Cavanagh

"A pilot shaft furnace was operated for one year at Steep Rock to produce special high-grade products from coarse ore, using lignite as fuel. The furnace is 10 ft in diameter and 60 ft high. When operated to heat coarse Steep Rock ore to drive off combined water and give a 64-per-cent-Fe product, the fuel consomption was 900,000 Btu's per long ton of product. The furnace was run in this way from September 1966 to January 1967 to establish the technique of feeding and discharging the furnace and controlling the gas composition and temperature. The furnace is similar in operation to a lignite water gas producer containing a large proportion of catalytic iron oxide. Steam injection is used to control the temperature. The product was tumbled in a rotary trommel to stabilize it. The resulting fines could be fed to the conventional pellet plant at Steep Rock. The furnace was next operated to make 77-per-cent-Fe metallized coarse ore. Several major modifications in de-sign were made and the furnace was successfully operated for short periods to maintain the required conditions to remove 75 per cent of the oxygen from the ore to give a 75-per-cent-reduced product at a grade of 77 per cent iron. The furnace cooling zone was operated under positive pressure, with internai alkaline water sprays to cool the charge. The product was discharged from the open bottom of the furnace without serions reoxidation. The metallized ore was magnetically separated from the discharge. Most of the charred lignite discharged along with the ore is re-cycled. Fuel requirement was 11,000,000 Btu's per long ton of product. This metallized coarse ore is intended for blast furnace feed. A short test run was carried out to establish the conditions for making a highly reduced melting stock for steel furnaces. To achieve 90 per cent reduction and over 90 per cent Fe, the furnace must be slowed down so that the production rate is about one-half the rate when making a 75-per-cent-reduced metallized product. Fuel requirement is 15,000,000 Btu's per long ton of product. The simple shaft furnace developed is similar to the top half of a blast furnace, with some major modifications to allow discharging into the open air. This Low Temperature Blast Furnace program has been technically successful and has resulted in making data available for the design of a commercial plant. Study of the commercial feasibility of large-scale production of metallized coarse ore at Steep Rock is still continuing."

Jan 1, 1968

By David M. Knowles, R. Gordon Gastil

"The Precambrian sedimentary series of the Labrador geosyncline, including iron formation, extends into southwestern Labrador and adjacent Quebec. The iron formation consisted of primary oxide, silicate, and carbonate facies which were deposited simultaneously in an irregular basin in response to migratory environmental conditions. The iron formation isochemically recrystallized to coarse-grained quartz-iron oxide, iron silicate, and quartz-iron carbon-ate rocks during prolonged regional metamorphism. The rocks are deformed on two deformation axes intersecting at large angles, and are characterized by isoclinal to recumbent folds. Parts of the formation have been profoundly affected by a post-metamorphic leaching and oxidizing environment."

Jan 1, 1959

By George H. Bodfish

This paper begins with a short history of air compressors, emphasizing their "roots" in the mining industry. It then describes the types of compressors available, including reciprocal, the various rotary positive-displacement compressors, and the centrifugal. The advantages and disadvantages of selecting a certain type of compressor over another are enumerated, considering customer requirements and operating costs, among other factors. Guidelines to operation and maintenance are discussed, including installation, monitoring and maintenance procedures. Finally, the paper addresses itself to future trends, with special attention being given to the system concept, the increasing use of rotary compressors, power consumption, reliability, packaging and noise attenuation.

Jan 1, 1978

By F. P. Agterberg

"IntroductionTHE KNOWLEDGE about the mineral resources in a region ranges from relatively precise ore-reserve estimates for known deposits to probabilistic estimates concerning the speculative resources which may be discovered in future at greater depths and in the less-explored parts of the region. Previously developed probabilistic methods for regional resource evaluation (1) are based on the following two assumptions.(1) The probability that a specific block of rock, or part of a region close to the topographic surface, contains undiscovered deposits can be estimate d by weighting selected geological, geophysical or geochemical parameters for that block. The weights are computed by considering similar environments which are known to contain deposits.(2) Some of the characteristics of the undiscovered deposits, such as ore tonnages and average grades of metals contained in the ore, can be evaluated by considering probability distributions f or known deposit data. These methods were initially applied to Precambrian deposits in the Abitibi Volcanic Belt of the Canadian Shield (1).Since 1972, statistical methods for quantitative resource evaluation have been applied to the occurrences of the mainly Paleozoic base metal deposits in t he Canadian Appalachian Region. The objectives of this project (Project Appalachia) have been discussed by Leech (2) in a paper that introduces 8 papers with results of the exploratory data analysis. Project Appalachia represents an effort to develop and apply methods of combining information and concepts from regional geology, metallogeny and geomathematics for computer- aided regional mineral resource evaluation."

Jan 1, 1977

By N. Ahern, L. Manoukian

"Cyanide is a leaching agent for precious metals commonly used in gold ore processing. Cyanide exists in various forms (including free, complexed as weak or strong complexes, and as ions such as cyanate and thiocyanate), so its detection, speciation and analysis in processing or environmental samples can be complex. This paper will review best practices for cyanide sampling and preservation in the field, interferences and pretreatment methods required prior to sample analysis and analytical methods that are used for cyanide species. Titrimetric, flow injection ligand exchange, spectrophotometric, colorimetric, potentiometric, amperometric, and chromatography techniques will be discussed and their chemistries, detection limits, advantages and limitations will be described.INTRODUCTION Cyanide is well known to be an extremely toxic species. Accurate cyanide measurement in effluent from mines is critical from an environmental perspective. Its measurement is also an important control parameter in the recovery of gold using cyanidation. Cyanide chemistry is diverse and complex, and cyanide analysis can be challenging as a result of and because of limitations in understanding of analytical methods. Various chemical mechanisms can form or destroy cyanide, and the sample matrix or preservation chemicals can also affect analytical results. These interferences make the collection of reliable cyanide measurements challenging and can start as soon as the sample is collected, during laboratory pre-treatment and during analysis. This paper reviews different methods of cyanide measurement. The basic chemistry of cyanide, best practices for sampling and preservation, as well as various methods of analysis will be discussed.CHEMISTRY The complexity of cyanide chemistry is well known (Beck, 1987; Delgado, Botz, Bucknam, Milasovljevic, & Staley, 2008; Botz, Milosavljevic, & Ward, 2013) and is attributed to the ability of cyanide to undergo: •,Volatilization •,Precipitation •,Adsorption •,Complexation with metals •,Oxidation to cyanate, ammonia, or cyanogen chloride •,Reaction with sulfur or sulfide minerals to form thiocyanate •,Redox reactions leading to the formation of cyanogen and cyanate •,Redox reactions (of some cyano complexes) •,Photochemical reactions (of some cyano complexes)"

Jan 1, 2017

By K. Schimann, H. D. Knipping, J. P. Fouques

"The Cigar Lake uranium deposit, in the Athabasca area of north Saskatchewan, was discovered in May 1981 by Cogema (Canada) Ltd., as operator of the Waterbury Lake Joint Venture.The deposit, which is devoid of direct surface expression, is located at the unconformity between the Lower Proterozoic (Aphebian) Wollaston Group meta-sediments and the Middle Proterozoic (Helikian) Athabasca sandstone, at a depth of 410 m to 450 m below surface.At the end of 1984, the deposit had been defined by 105 mineralized holes over a length of 1800 m and a width of between 25m and 105m. It has the shape of flat-lying /em 5 m to 30m thick and shows a remarkable longitudinal and lateral continuity from the information obtained to date. A well defined bulge of the unconformity underlies the mineralized zone over its entire length.The deposit appears to be controlled by an east-west trending structure within which a particular rock facies (""augen gneiss'') has developed in the graphitic metapelites of the Wollaston Group. It is surrounded by a strong alteration halo affecting both sandstone and basement, characterized by extensive development of Mg-AI rich clay minerals (illite-chlorite). The mineralization is hosted principally by the Athabasca sandstone, and consists mainly of uraninite and sulfa-arsenides of nickel and cobalt. Numerous geochemical and geophysical surveys have been carried out in the Cigar Lake area, and although no specific geochemical or geophysical anomaly can be directly associated with the mineralized body, there may be locally a good coincidence.However, a combination of several methods proved extremely useful in interpreting the regional geology and defining the drilling targets within the favourable areas.Although the Cigar Lake deposit shows many similarities with several classical deposits of the Athabasca region, it is characterized by the intensity of its alteration processes and the presence of massive, extremely high grade mineralization.At the end of 1984, the global geological reserves estimated by geostatistics on the main mineralized ""pod"" of the deposit amounted to 110,000 metric tonnes of uranium at an average grade of 12.2% U, with a precision of 25% at the 95% confidence level."

Jan 1, 1986

By Dart Wantland

"AbstractThe scope of geophysics in civil engineering and the nature of exploration geophysics are briefly discussed. Engineering problems amenable to geophysical attack are illustrated by specific examples. The various methods available, accuracy of results, and costs are treated. The possibilities of new uses of geophysical techniques are pointed out.IntroductionTHE SCOPE of geophysics in engineering is different than in oil or mining exploration. In civil engineering, geophysics solves specific problems; as for example, what is the depth to bed-rock along the axis of a proposed dam? The area to be surveyed is of limited extent, and the subsurface information .sought is relatively near the surface. The engineering geophysicist is not called upon to investigate geological basins or extensive mineralized areas or to probe for data to thousands of feet in depth. The geophysical tools employed in the three fields are, however, quite similar; the differences are mainly in the objectives.The Natural Geophysical ExplorationThe terms geophysics and geophysical exploration have been used heretofore and will .be employed in what follows. The question is, therefore, What is geophysical exploration?Geophysical exploration is a line of field work where measurements are made at the ground surface with special instruments to get geological subsurface information. Briefly stated, geophysics is a form of exploration that supplements geological work. It is a blend of physics and geology since physical measurements are made •at the surface of the ground that can be interpreted in terms of subsurface conditions."

Jan 1, 1953

By S. S. Burns

"AbstractShovels of 18 cubic yard capacity and larger are described which incorporate advanced technology and techniques providing performance and operation tailored to meet the needs of open-pit mining.To achieve the goal s of increased production at lower cost with consideration of maximum availability, lower energy consumption per ton and low •impact on pit power, Harnischfeger Corporation developed a solid -state drive system (""Electrotorque"" - P&H trademark) and applied unique transmission methods.To date, more than 250,000 hours of experience in different parts of the world under varying operating and environmental conditions has proven that the ""Electrotorque"" shovel is the shovel of the future, today.This paper will discuss the electrical features and touch briefly on some mechanical features.Introduction to ""Electrotorque""THE hoist, crowd, propel and swing machinery of an electric mining shovel are driven by direct-current motors.A D.C. motor is used instead of an A.C. motor because the torque output per ampere input is at a maximum and the fact that it is doubly-fed (armature and field ) provides optimum flexibility in control.The power that is available in the pit is alternating current power. It is therefore necessary to change or convert this A.C. power to D.C. power so that the D.C. motors can be used."

Jan 1, 1977

By A. Alfantazi

Recently, titanium and its alloys have been the materials of choice for the liner and internal components of autoclaves used to extract Ni and Co from laterite ores. There have been many corrosion incidents ranging from localized attacks due to scale formation or welding, to damage caused by pockets of concentrated acid. Most of the literature focuses on methods to avoid the corrosion altogether. Little has been published to increase awareness of the chemistry at these conditions. For this paper, a literature review of the thermodynamics of titanium was undertaken to decipher the slew of information available. E-pH diagrams were constructed from select data and compared with the results of electrochemical experiments. Since nickel laterite leaching takes place in sulphuric acid, and in many cases chloride concentrations are very high, the Ti-H2O, Ti-Cl--H2O and Ti-SO4---H2O systems were considered.

Jan 1, 2004

By Marc R. Laflèche, Suzanne Paradis, A. Shirley Péloquin, Harold L. Glbson, Robin Potvin, Pierre Verpaelst

"The Archean Blake River Group is best known from a central volcanic complex in Rouyn-Noranda. This volcano-tectonic depression, delimited by the Hunter Creek fault to the north and the Horne Creek fault to the south, is interpreted to be a cauldron approximately 20 km in diameter. Its western and eastern boundaries are the Flavrian Plutonand the D'Alembert shear zone respectively. The complex has an exposed stratigraphic thickness of 10.5 km. Two cycles, composed of andesitic units overlain by bimodal, andesite - rhyolite units, are observed in the area, and are, in turn, overlain by an andesitic unit interpreted to be the lower part of a third cycle.The southern sector of the Blake River Group, south of the central volcanic complex, is considered to be outside the limits of the cauldron, but partly contemporaneous with it. The maximum stratigraphic thickness exposed in this area is 4 .6 km. At least two cycles occur in this sector. The oldest unit, a pre-cauldron andesitic to basaltic unit, occurs only in the southern part of the sector. In the north, two partial andesite - bimodal cycles, interpreted as contemporaneous with the cauldron volcanism, are observed.The eastern sector of the Blake River Group, east of the central volcanic complex, apparently overlies the complex. Two units are observed in this sector: a lower bimodal unit and an uper andesitic unit. The bimodal unit is coupled with the uppermost andesitic unit of the central volcanic complex to form a cycle, and the andesitic unit is considered to be the uppermost unit of the Blake River Group. The total exposed stratigraphic thickness in the sector is 2.5 km.The western sector of the Blake River Group, north and west of the central volcanic complex, is interpreted as the lateral equivalent of the complex. Three andesite - bimodal cycles are exposed in this sector, giving a total stratigraphic thickness of9 .5 km. The two lower cycles correspond directly to the central volcanic complex cycles; this correlation is facilitated by two stratigraphic marker units observed on either side of the Hunter Creek fault: the Fish-roe rhyolite flow, east of the Flavrian pluton, and a spherulitic rhyolite lapilli-tuff, west of the Flavrian pluton.Many of the volcanogenic massive sulphide deposits found in the central volcanic complex are spatially and temporally associated with synvolcanic faults, and felsic domes and feeder dykes that are the sites of felsic volcanism in the bimodal units. However, these features also occur outside the central volcanic complex, and the similarities recognized in this work between the complex and the surrounding area suggest that such deposits need not be restricted to the central volcanic complex. The presence of volcanogenic massive sulphide deposits outside the complex confirms this."

Jan 1, 1990

By G. R. Waters

"The technology behind industrial applications such as Hydrometallurgy continues to evolve, as do the corresponding regulations and specifications that ensure the safety of workers and the environment. Valves make up key aspects of this technology, and often represent the single point of failure for entire operations. More often than not, the valves being used in Hydrometallurgy applications are known as Severe Service Valves (SSVs) due to their ability to withstand the extreme conditions. Most experts agree that SSVs are identified by applications, and that these applications are challenging to the valve’s ability to provide a minimum acceptable level of performance over a minimum acceptable duration. The Manufacturers Standardization Society (MSS) of the Valve and Fittings Industry has designated Ross Waters, President of CGIS, as Lead to the Task Force put in place to determine the minimum requirements a valve needs to be able to perform to when faced with extreme conditions, whether from pressure, temperature, toxicity, solids, or usage. This paper serves to determine what the minimum requirements are for SSVs in Hydrometallurgy applications. It will draw on five decades of industry experience from one of Canada’s leading valve experts.INTRODUCTION Severe Service Valves Severe Service Valves (SSVs) mean different things to different people. Until today, defining SSVs had little if any global agreement or recognition. That is about to change as the Manufacturers Standardization Society (MSS) has accepted an application to produce a Standard Practice so defining them. This paper provides information about the selection of SSVs in all industries but focusses on metallurgical processes and applications and offers examples to illustrate the successful and unsuccessful use of these valves. All of this with the purpose of raising the awareness of the industry on all sides, from the suppliers and manufacturers, specifiers and to the users and owners of them. It also supplies tools to understand where and why to separate SSVs from general purpose or commodity valves (GPVs). SSVs are often identified by applications, and these applications are challenging to the valve’s ability to survive. Within these applications the elements that make the service severe are being analyzed, quantified and qualified. From this, we expect to offer objective and repeatable definitions and guidance to improve the experience of SSVs, reduce unnecessary costs, provide longer service life and process runs, improve safety and reduce environmental issues."

Jan 1, 2017

By K. R. Barnard, K. D. Marte, T. V. Gamarano

"The first commercial scale application of CSIRO’s direct solvent extraction (DSX) technology has been in operation at the Boleo project in Mexico since December, 2015. In this application, DSX is a synergistic solvent extraction system consisting of the extractants LIX 63 and Versatic 10 for recovery of cobalt and zinc from a solution background of manganese, magnesium, and calcium. Key operating parameters such as metal extraction, phase disengagement and extractant stability are summarized and discussed in this paper.INTRODUCTION Commissioning of the Boleo processing plant, located on Mexico’s Baja peninsula, began with the copper circuit starting in late 2014, with first copper cathode production achieved in January, 2015. The cobalt and zinc circuits began commissioning in December, 2015 with first zinc sulphate monohydrate (ZSM) and cobalt cathode production achieved in February and April, 2016 respectively. The Boleo project flow sheet and development has been described in detail in previous publications (Dreisinger, et al. 2005; Dreisinger, Baxter, & Molnar, 2006; Dreisinger, et al. 2008; Dreisinger, et al. 2009) and is summarized schematically in Figure 1. Boleo is a mixed oxide/sulphide Cu-Co-Zn-Mn high clay deposit that is processed in a whole ore, atmospheric, oxidative and reductive, sulphuric acid/seawater leach. Copper is recovered as cathode by conventional solvent extraction and electrowinning. Cobalt and zinc are recovered, from a solution background of manganese, magnesium, and calcium, by CSIRO’s synergistic solvent extraction technology Direct Solvent Extraction (DSX). Cobalt and zinc are bulk stripped from the DSX circuit and then further purified by phosphinic acid solvent extraction to produce zinc sulphate monohydrate granules via spray dried granulation and cobalt cathode rounds via divided cell electrowinning."

Jan 1, 2017

By C. A. Young, H-H. Huang, L. G. Twidwell

Equilibrium calculational software programs can be effectively utilized to model important parameters in aqueous and aqueous/solid systems, e.g., activity or concentration, solubility, temperature, solution pH, solution potential, and ligand complexation. In this regard, the calculational program ST ABCAL will be demonstrated. Illustrative examples for the creation of diagrams such as potential-pH, and activity or concentration-pH will be presented to demonstrate the fundamentals in real hydrometallurgical systems. Speciation, titration and mixing will be used to simulate or predict operational processes. Berkeley Pit water from a flooded abandoned copper open-pit mine will be used to illustrate the modeling process. According to analytical results the water contains about 20 important constituents. In addition to measured potential and dissolved oxygen, there are two distinctive oxidation/reduction couples. Concentration and other experimental parameters are seldom matched to each other and 12 different conditions have been identified. Water for each condition must be speciated in order to find the best-fit model. The STABCAL program will be used for the modeling calculations and the implication of the water chemistry to defining treatment opportunities will be discussed.

Jan 1, 2005

By L. Dekker

"In 1979 Chevron Standard Limited and Irving Oil Limited intersected a thick, high-grade sylvinite zone in the Windsor Group in the Chevron Irving Malagawatch No. I well in central Cape Breton. This well was the third and final hole of a program designed to evaluate a non-commercial oil discovery made by Chevron Standard's Mineral Staff in 1978 while carrying out base metal exploration. Nine holes were subsequently drilled to evaluate the significance of the potash discovery. The delineation drilling proved the Malagawatch structure to be complex with the potash zone showing erratic grade and thickness distribution. Based on the drill information the potash accumulation at Malagawatch is uneconomic, however, other salt ""structures"" in the Bras d'Or Basin may in time prove to have better potential.History of DiscoveryIn 1972 Cuvier Mines discovered the Gays River lead-zinc deposit (MacEachern and Hannon, 1974) which prompted Chevron Standard's Minerals Staff to carry out a study of the Windsor basins in Nova Scotia (Figs. I and 2). As a result of this program several carbonate-hosted lead-zinc prospects were identified in the basal Windsor carbonate; one of these was at Malagawatch on Cape Breton Island . In 1978, after preliminary exploration surveys, a diamond drill program commenced consisting of 5 BQ holes (Fig. 3), three of which tested the basal carbonate. Instead of the reefoid bank facies of the Gays River Formation (Giles et al., 1979), the favoured host for economic base metal mineralization, this carbonate was developed as a laminated, pelletoidal, lime packstone more characteristic of the facies equivalent Macumber Formation (Schenk, 1967). While drilling one of these holes, No. 3-78, oil scum was intermittently detected on the drilling mud. The hole was abandoned at 191 m in anhydrite, without having reached the basal limestone."

Jan 1, 1985

By Zoltan Hajnal

Magnetic studies have been carried out on 88 surface and 157 underground samples from the Coronation Mine area of northern Saskatchewan. The intensity of the surface samples was compared to trace element determinations from the same locality. A good correlation was found between the titaniferous constituent of the rocks and the intensity of magnetization. From the direction of the remanent magnetism, two virtual geomagnetic poles were determined -latitude 12° 54' North, longitude 158" 17' West; and latitude 23" 42' North, longitude 163° 45' West. The sulphide ore specimens showed anisotropic susceptibility characteristics. A relationship was found between the measured maximum susceptibility values of the ore specimens and the direction of the tectonic forces which are considered to have formed the structure at the Coronation mine. Introduction T HIS paper summarizes the results of a study of the magnetic properties of samples from well-known Precambrian formations. The observed data give information for an interpretation of the magnetic field conditions in Precambrian times. The high magnetic intensity values indicate the importance of the study

Jan 1, 1965

By C. DeLong

"The Mt. Milligan porphyry copper-gold deposits are in central British Columbia, 155 km northwest of Prince George. Mineralized outcrops and float were discovered in the Mount Milligan area by prospecting. The most recent discoveries, which utilized lithogeochemistry, were in 1983. Areas containing the outcrops and float then were investigated by geological mapping, soil and lithogeochemical sampling, ground and airborne geophysical surveys, trenching and diamond drilling. This work led to the discovery of the Mt. Milligan Main deposit in 1987 and the Southern Star deposit in 1989. Extensive diamond drilling continued until 1991 and delineated a measured and indicated resource of 299 million tonnes grading 0.45 g/t Au and 0.22 % Cu from the combined deposits.The Mt. Milligan deposits lie within the Early Mesozoic Quesnel Terrane and are hosted by porphyritic monzonite stocks and adjacent volcanic rocks of the Takla Group. The Mt. Milligan Main deposit is centred around the MBX stock and Rainbow dike, and the Southern Star deposit around the Southern Star stock.Potassic alteration is extensive within the stocks and in volcanic rocks adjacent to the MBX stock and Rainbow dike. Propylitic alteration surrounds the potassic alteration and decreases in intensuy away from the stocks. Mineralization consists mostly of pyrite, chalcopyrite, lesser magnetite, and minor bornite, molybdenite and gold.Mineralogical zoning is well-developed within the deposits. A biotite-rich subzone forms the core of the potassic alteration zone and hosts most of the copper and gold. Numerous polymetallic veins lie within the propylitic alteration zone just beyond the limit of porphyry-style copper-gold mineralization."

Jan 1, 1995

By Lloyd F. Dunham

"Crucial to the implementation of new computer-based information systems at Sudbury Operations of Falconbridge Limited was a data communications network that would take computing power to the various mine and plant sites. Falconbridge required a capability to provide on-line data entry, inquiry, and reporting capabilities in three geographical areas, six mines, two mills, a smelter, approximately fifty shops, seven warehouses and numerous administrative offices throughout the Sudbury basin.Conventional cabling methods were rejected based on the projected cost of installation of necessary cables; lack of flexibility to meet the changing requirements of the mine environment; and the risk of losing service to an entire area depending on solitary communication lines.Instead, Falconbridge selected and installed a Data Carrier System (DCS) and Packet Switching Communication System from Teltone Limited, Markham, Ontario. This combined system ""piggy-backs"" computer data over voice-grade twisted pair wire, bringing data to the associated PBX equipment. From there data packets are assembled and routed to the central computer site where they are disassembled for entry into the host machine.Falconbridge has been successful in using existing technology to solve communications problems in a difficult environment. Plans for the future of this network will increase its utilization for technical and real time data communications in addition to the business systems workload it now handles. The Computer Services group in Sudbury is confident that the data highway will handle communications traffic well into the future.IntroductionIn late 1984, the Sudbury Operations of Falconbridge Limited undertook a review of their existing business computer systems. The results of this review indicated that there was an opportunity to improve the timeliness and quality of information coming from the existing computer-based systems while achieving an investment payback by undertaking the project. The greatest benefits from this project would be achieved if the computing tools could be delivered to the employees that were the day-to-day users of the data. Falconbridge's existing business systems were oriented to the batch mode of processing. An alternative solution to using the existing programs had to be found."

Jan 1, 1988