Search Documents

By Phil Molloy

"In March, 1968, Skega Ruh her Liners were used to reline the shell of an 8' x 12' Allis Chalmers ball mill.This mill is used to regrind the cyanided pulp from 58i -200 mesh to 92% -200 mesh prior to this pulp passing to the flotation circuit, at approximately 450 tons per day.Before the use of rubber liners, the regrind ball Mill shell had been lined with single wave ni-hard liner!'. These liners had an average life of five years. Ni-hard end liners were used both prior to and during the use of rubber liners, as the life of the ni-hard end liners was about seven years, and it was thus felt that little economic benefit would be realized by lining the ball mill ends with rubber.The rubber lining used has a thickness of 57.15 millimeters and the square shaped lifter bars which are spaced at 14~ inch centres, have a 4"" x 4"" cross-sectional dimension.With the use of ni-hard liners, the consumption of 1 1/4 forged steel balls averaged 1.062 pounds per ton, Using rubber liners the consumption of l~"" forged steel balls increased to 1.368 pounds per ton. Also the level of the ball load which previously had been kept at approximately 18 inches below the mill discharge, had to be increased to approximately 8 inches below the mill discharge in order to effect the same grind.The initial gri4ding performance of the newly relined mill was also poor, until the leading edge of the rubber lifter bars, which were square shaped in cross-section had been worn to a rounded profile. These lifter bars were replaced after 4 years and 3 months of operation.The advantages of rubber liners in our opinion is as follows:"

Jan 1, 1974

By Norman Orr, J. W. Gregg, Jack Wahl

The Pembina Cardium pool is a low permeability, stratified, solution-gas drive reservoir. Water-flooding has proven to be an effective means of pressure maintenance for all areas of the pool in which an economic rate of water injection can be maintained. The majority of water injection wells in the pool are converted oil well~ with capacities greater than 100 millidarcy-feet. If the average injection rate per unit of capacity can be in-creased the lower capacity areas of the pool can be economically flooded. Theory, laboratory work, and two . early miscible-flooding projects with-in the pool suggested that average water injection rates for converted wells could be increased two to three-fold by the initial injection of natural gas liquids and natural gas. How-ever, these two early projects received volumes of natural gas liquid!:' and high-pressure natural gas which would be economically prohibitive for routine stimulation. Area D, one of the Five-

Jan 1, 1962

By Atsushi Sainoki

Blast vibration induced by mining activities, such as stope production blasts, could lead to the initiation of seismic events that inflict damage to mine openings. In this paper, the effect of stope production blasts on nearby fault is examined. First, validation of blast vibration attenuation is performed with a numerical model representing a single blast hole through comparison with that calculated from charge-weight scaling law derived from in-situ data. Subsequently, a mine-wide scale model with a fault parallel to a steeply dipping, tabular ore deposit that is mined out with sublevel stoping method is generated, and the stopes are extracted and backfilled with static analysis to simulate burst-prone conditions on the fault. Based on the stress states, dynamic analysis is performed, in which blast vibration is applied to grid points on a stope wall on the hanging wall side. This assumes 9 blast holes located close to the wall, and blast-induced particle velocities that consider the positional relationships between the assumed blast holes and the stope wall are applied. During the dynamic analysis, blast sequence is considered, and stress states and shear displacement on the faults are examined. It is found from results that, after a rise in normal stress on the fault due to compressive waves induced by the blasts, the normal stress decreases because of the reflection of the compressive waves on the fault. The reduction in the normal stress due to the reflected waves is found to be large enough to cause the fault to slip. The results also show that the level of normal stress eventually keeps decreasing with time as the blast sequence proceeds and that an increase in shear displacement on the fault is accompanied by a decrease in normal stress. This study clarifies the mechanism by which blast vibration causes the fault to slip. In addition, the simulation technique to apply blast vibration that takes into account blast sequence and the locations of blast holes to a stope wall is developed.

Aug 1, 2013

By B. Stettner, J. Asante, S. Abraham

The levels of nitrogen in steel produced in various metallurgical vessels vary significantly. For example, the tap nitrogen levels in steel produced in the BOF are around 4Oppm, as compared to 70-100ppm in both DC and AC electric arc furnaces. Given the pressing need to reduce nitrogen levels in steel to satisfy customer demand, IPSCO Inc. has gained considerable experience in controlling nitrogen levels in steel over the course of the last three years. Hence, a cost effective process has been developed through an intensive nitrogen control program from steel melting in the EAF through to the continuous slab casting stage. This paper describes the practices employed at each stage of the steelmaking process that have enabled IPSCO Inc. to reduce and control nitrogen levels in steel.

Jan 1, 2004

By I. M. R. Duarte, J. A. Rodrigues-Carvalho, F. R. S. Rosa, A. B. Pinho

"This paper aims to contribute to the knowledge of the mechanical properties of the shales and greywackes which constitute the flysch-type deposits of the Baixo Alentejo Flysch Group, in the south of Portugal. These formations are flysch-type deposits constituted by sequences of usually thick greywacke beds alternating with thin shale beds, which include sometimes intercalations of conglomerate beds. All the sedimentation of these flysch formations was controlled by tectonics. At the same time, should have occurred along with the first Hercynian deformation phase, a low-grade metamorphic event (chlorite zone), that affected these flysch deposits. This study highlights the influence of anisotropy and heterogeneity of these flysch rocks on their physical and mechanical characteristics. The anisotropy verified in some physical properties and on mechanical properties, due to the foliation makes difficult the sample preparation for the laboratory tests. Besides, it induces a scattering of the properties values measured, as for example, the strength and the deformability. The heterogeneity is related to the main features of these geological formations, which are constituted mostly by thinly stratified greywackes and shale beds, which sometimes may affect the results of the laboratory tests making them less representative. The study is made by using both shales and greywackes that constitute these flysch-type deposits in order to evaluate their geotechnical properties, mainly of the shales. Samples of these two rock materials, are tested accordingly a laboratory testing programme, which includes which included mineralogical analysis (X-ray diffraction), physical tests (bulk density, porosity, and void index) and mechanical tests (uniaxial compression, and deformability tests). INTRODUCTIONOne of the factors that most influence the geomechanical behavior of rocks, as well as rock masses is the anisotropy. The word anisotropy comes from two Greek words ""anisos"" (meaning uneven) and ""tropos"" (meaning direction). A body or material is considered to be anisotropic, where the same property has different values depending in which direction it is measured, therefore, an anisotropic material is one whose magnitude of the properties depends on the direction in which these are studied or measured. Otherwise, it is about an isotropic material. However, the fully isotropic materials are quite rare in nature."

Jan 1, 2015

By L. J. Cabri

A gold sample assaying 11.4 g Ault was selected for this study. Approximately 99% of the gold in this sample occurs as discrete gold minerals; the balance occurring as invisible gold in pyrite (determined by SIMS analysis). The sample was coarsely ground and sieved, yielding -38, 17, 22 and 22 wt.% in the -400+160 um, -160+80 um, -80+40 µm and -40 µm size fractions. Assays of the size fractions gave a gold distribution of -32, 20, 21, and 27% respectively. Processing with the hydroseparator (model HS-02) gave two tailings products and one concentrate from each size fraction. Assays of the concentrate from each size fraction gave gold recoveries of -7, 7, 24, 19%, respectively. Polished sections were prepared from each hydroseparation product and studied by image analysis to automatically search for gold minerals. Calculations were done using the surface area of the grains of gold minerals found on the polished sections.

Jan 1, 2005

By A. R. Laplante

Gold recovery early in the flowsheet, typically from the primary grinding circuit, has seen significant advances in the past three years. Some of the advances achieved under the auspices of the AMIRA P420B Gold Processing Technology project are reviewed. The areas covered are gravity-recoverable gold (GRG) characterization, GRG behaviour in classification, gravity recovery simulation and the link between gravity recovery and cyanidation.

Jan 1, 2005

By F. Flores

With the World Summit for Sustainable Development planned for 2002 in mind, nine of the world's largest mining companies decided to initiate a project to examine the role of the minerals sector in contributing to sustainable development, and how that contribution could be increased ? the Mining, Minerals and Sustainable Development Project (MMSD). This project assumed from the start that sustainable development could provide a useful framework to guide the minerals sector which main goal was integrating economic activity with environmental integrity, social concerns, and effective governance systems. The broad steps of MMSD project strategy can be grouped into four major categories: increase understanding of sustainable development; create organizational-level policies and management systems for implementing the principles of sustainable development; collaborate with others with common interests to take joint steps towards sustainable development, and; increase our ability to work towards sustainable development at the local, national, and global levels. In opinion of the article's author, to go ahead with the MMSD strategy and achieving the sustainable development objectives, it is necessary to consider the concept of self-organization, fundamental of the emergent new scientific paradigm, and the consequent epistemology and values that conform a supporting culture for sustainable development.

Jan 1, 2007

By W. McCombe, G. Remple, L. Nightingale-Mercer

The McClean Lake Mill is located approximately 850 kilometres north of Saskatoon, Saskatchewan, Canada, and is operated by Orano Canada Inc. (Orano). The mill was designed to process high grade uranium ores, and a multi-year expansion was completed in 2014 to increase its production capacity to 24 Mlbs U3O8 per annum. The mill also underwent various upgrades to allow it to safely transition from processing low grade ores to high grade ores from the nearby Cigar Lake Mine. During the metallurgical test work on the Cigar Lake ores, it was identified that some ore zones of the deposit have a propensity to generate hydrogen gas during acid leaching. Hydrogen is a volatile and explosive gas, which poses obvious safety concerns in the leaching circuit. Uranium processing is further complicated by the fact that an oxidant in the form of oxygen gas or hydrogen peroxide is required to regenerate iron in the leach, which further increases the risk posed by hydrogen gas. During 2013 Orano and its consultant Hatch designed and engineered several novel upgrades to the leaching circuit to mitigate the risk of hydrogen gas evolution in the process. Best in class technology was utilized in addition to control and operating strategy changes to ensure the leaching circuit could be safely operated with ores that evolve hydrogen gas. This paper reviews the design concepts and modifications implemented on this unique and challenging project, and also provides an update on the operational reality of hydrogen in the circuit gained through five years of operational experience with hydrogen evolving ores.

Jan 1, 2020

By T H. Clark, R P. Doig, V. A. Saull, R B. Butler

Terrestrial heat flow has been determined for four boreholes in the Montreal area. The mean value of the results (uncorrected for glacial effects) is 0.790 ± 0.053 x 10-6 cal/ cm2/sec (95 per cent confidence limits). Thermal gradients were determined using a thermistor probe and d-c bridge, and also by a new method using a probe-contained phase-shift oscillator, the output frequency of the oscillator being a function of probe temperature. Thermal conductivity determinations were made on core from the boreholes, using a divided bar apparatus. INTRODUCTION T HIS paper concerns the terrestrial heat flow in the St. Lawrence lowland of Quebec, as determined from measurements on four of the numerous boreholes drilled in this region for gas and oil. The work has been supported by Geological Survey of Canada Re-search Grant 3-58, awarded to T. H. Clark and V. A. Saull. This sup-port is hereby gratefully acknowledged.

Jan 1, 1962

By T. J. Langan, M. Ramajayam, T. Dorin

"6xxx-series Al alloys are the most commonly used alloys in the automotive industry as they have an appropriate balance of strength, corrosion resistance and formability. The main strengthening phase in these alloys is the ß’-Mg2Si precipitates. One opportunity to achieve stronger 6xxx-series Al alloys, without affecting corrosion and formability, is the use of Sc. The main challenge of using Sc in 6xxx-series lies in the heat treatment, which must be designed to allow for a fine precipitation of both Al3Sc and ß’-Mg2Si. In this work, two model alloys are used, an Al-Sc-Zr and an Al-Mg-Si-Cu-Sc-Zr, to explore the impact of the 6xxx-series key elements (Mg, Si and Cu) on the Al3Sc precipitates. Transmission electron microscopy and atom probe tomography are used to investigate the precipitates present in the microstructure after casting. We find that higher Si content results in the formation of dispersoids upon casting. The average composition of these dispersoids is (Al0.8,Si0.2)3 (Sc0.888,Zr0.024,Mg0.08,Cu0.008). A closer look at the solid solution reveals that most of the Sc and Zr is supersaturated after casting even in the presence of Mg, Si and Cu. We discuss the impact of these results on the design of a suitable heat treatment for 6xxx-series alloys with Sc.INTRODUCTION The most common strategy to strengthen aluminum (Al) alloys is by micro-alloying to form a fine distribution of precipitates (Gladman, 1999). Whilst precipitates enhance the strength, this is often done to the detriment of ductility and corrosion performance (Davis, 1999). The 6xxx-series Al alloys are heavily used in the automotive industry as they offer an appropriate balance of strength, ductility and corrosion resistance (W. S. Miller et al., 2000). The strength increment in these alloys comes from the formation of the ß’–Mg2Si and the quaternary Q’ phase (Chakrabarti & Laughlin, 2004; Polmear, St. John, Nie, & Qian, 2017). One opportunity to achieve stronger 6xxx-series alloys, whilst keeping good balance of corrosion resistance and formability, is the use of small additions of scandium (Sc). Sc is one of the most potent strengtheners in Al alloys (Dorin, Ramajayam, Vahid, & Langan, 2018; Røyset & Ryum, 2005). Most of the strengthening benefits from Sc come from the formation of fine Al3Sc dispersoids. The following strengthening mechanisms apply to Sc: 1) Solid solution strengthening, 2) precipitation hardening, 3) inhibiting recrystallization, 4) assisting nucleation of other strengthening phases (Dorin, Ramajayam, Lamb, & Langan, 2017). As compared to other dispersoid phases, Al3Sc dispersoids have good electrochemical compatibility with Al alloys and hence do not affect their corrosion resistance (Cavanaugh, Birbilis, Buchheit, & Bovard, 2007). The coarsening resistance of Al3Sc is often improved by adding zirconium (Zr), as it forms a Zr rich shell around Al3Sc which prevents Sc from moving across the interface."

Jan 1, 2018

By E. Mohammadi Zahrani

In this study, Mg-doped fluorapatite (Mg-FA) nanopowders were prepared through a sol-gel, technique and characterized. Designated degree of Mg2+ ions incorporation into the apatite structure was indicated by the x value in the general formula of (Ca10-xMgx (PO4)6F2), where x=0, 0.25, 0.5, 0.75, and 1. XRD, AAS, FTIR and TEM techniques were utilized to characterize the synthesized nanopowders. In vitro bioactivity of the powders was evaluated in simulated body fluid. Powders had a crystallite size less than 100 nm. It was concluded that Mg-substitution could alter bioactivity and dissolution behaviour of Mg-FA. These two parameters were proportional to magnesium content of the powders.

Jan 1, 2010

The Anglo Platinum Mogalakwena North concentrator was one of the first three hard rock mineral processing applications to utilise a HPGR circuit in preference to a SAG milling circuit. This was driven by the extreme competence of the ore that had given rise to throughput issues on the original South Plant. Despite more than adequate capacity and performance of the individual comminution units, the circuit has struggled to obtain full design capacity. A thorough review of the integrated performance of the circuit revealed a wide range of bottlenecks and underutilised parts of the circuit arising from design issues. Interestingly, the major opportunities lie in materials handling issues and mismatch of loads about the circuit. This paper presents the high-level outcomes and the associated opportunities, and is pertinent to all HPGR circuit designs.

Jan 1, 2012

When selecting a method for monitoring crack growth in pipeline steel, the sensitivity or crack-size resolution plays a dominant role. Even though there are several visual and non-visual methods, the direct current potential drop (DCPD) method is very effective for monitoring crack growth because of its resolution. This method has been used for the past few decades and has gained increasingly wide acceptance in fracture research as one of the most accurate and efficient methods for monitoring the propagation of cracks. Furthermore, most R&D experience has proven that the electrical potential method can be used in most "aggressive" environments. For these reasons, the DCPD method was selected to design a testing machine to monitor corrosion fatigue crack growth. The use of finite-element modelling is shown to facilitate the application of the DCPD method for monitoring crack growth in steels. The 2D model calibration provided a good description of the test data and proved more accurate than the analytic Johnson's formula.

Jan 1, 2005

By Michel Dagbert, Mohammed Harfi

"Abstract - The Draa Sfar polymetallic deposit, at about 16 km NW of Marrakech in Morocco, is a massive sulfide zone at the contact between an underlying volcanic and an overlying clastics sequence. The mineralized body is a flat lens with schistosity and "boudinage," tilted to the west and with a strong dip to the east. The lens extends over a strike length of about 2 km and from surface to a depth of about 1 km, with thickness varying from 1 m to almost 30 m. It has been intersected by about one hundred surface drill holes and, in its south part, by about thirty underground fan holes from two exploration levels at depths of 300 m and 400 m. On these two levels, the massive sulfide zone has been channel sampled over a cumulative length of about 0.7 km. Results from drill and channel samples are used to estimate the resources of the orebody according to several methods: sections, polygons around intercepts on a longitudinal plan, grids on the same longitudinal plan with various distance weighting methods including kriging and, finally, a 3D grid with the same range of interpolators. A comparison of the various estimates delineates the important factors in deriving resources for this type of deposit. Those factors are mostly geological and related to the interpretation of the geometry of the two limiting surfaces of the zone. For the 3D gridding, the authors have devised a new and original method that constrains the interpolation of blocks from samples to a geometry of limiting surfaces. The resulting model shows internal grade variations that parallel fluctuations of zone thickness and orientation without having to re-orientate the search window in each block. Résumé - Le gisement polymétallique de Draa Sfar, situé à environ 16 km au NW de Marrakech est un horizon de sulfure massif au contact d’une formation volcano-sédimentaire de base et d’une formation détritique sur-jacente. Le corps minéralisé se présente sous forme d’une méga-lentille aplatie, schistosée, boudinée et déversée vers l’ouest avec un fort pendage vers l’est s’étendant sur une longueur de 2 km et une profondeur de près de 1 km avec une épaisseur variant de moins d’un mètre à près de 30 m. Il a été reconnu par plus d’une centaine de sondages de surface et, dans sa partie sud, par une trentaine de trous souterrains en éventail à partir de deux niveaux à des profondeurs respectives de 300 m et 400 m. Sur ces mêmes niveaux, des traçages ont permis de rainurer le minerai sur une longueur cumulée de 0.7 km. Les données de sondage et de rainurage ont servi à estimer les ressources du gisement selon plusieurs méthodes : sections, polygones sur longitudinale, grille sur longitudinale avec différentes pondérations en fonction des distances incluant le krigeage et enfin grille tridimensionnelle avec le même éventail de pondérateurs. La comparaison des estimés obtenus permet de mettre en évidence les facteurs importants dans l’estimation des ressources de ce type de gisement. Ces facteurs sont essentiellement géologiques et relatifs à l’interprétation de la géométrie des limites des corps minéralisés. Pour l’estimation sur grille tridimensionnelle, on a mis au point une technique originale qui calque l’interpolation des blocs à partir des échantillons sur cette géométrie des surfaces de contact. Le modèle résultant montre des variations internes de teneurs qui épousent les fluctuations d’épaisseur et d’orientation de la zone sans qu’il soit nécessaire de ré-orienter les fenêtres de recherche dans chaque bloc."

Jan 1, 2002

By Fritz F. Prugger

In August, 1970, during routine shaft grouting, a major water source was intersected. Water and quicksand under very high pressure entered the shaft at a rate of 65 m3 per minute. The mine and both shafts were flooded. The breach was sealed simultaneously from within the shaft and through a relief hole drilled from surface. The mine was dewatered, rehabilitated and the equipment was restored. Production resumed two years after the accident.

Jan 1, 1979

By F. Khomamizadeh

In this study, deep cryogenic treatment was applied to A319 cast aluminum samples. Although the cryogenic treatment didn't have any significant effect on mechanical properties of the well degassed and fluxed samples, but the tensile strength of the samples containing a considerable amount of gas and shrinkage defects was improved surprisingly, This improvement was attributed to the strengthening of the a-aluminum matrix which slows down the propagation of the existing defects. There was no significant increase in the hardness after cryogenic treatment, The abrasion resistance of the alloy was improved after cryogenic treatment, by developing a homogeneous protector shield, composed of abrasive grains penetrated into the soft aluminum matrix and kept tight.

Jan 1, 2005

By W. A. Dixon Edwards

Industrial mineral production in Alberta, worth $468 million in 1997, comes from a dozen types of industrial minerals, mined by about 400 producers. Cement and lime from Paleozoic limestone formations exposed along the Rocky Mountains account for the greatest production value. Sand andgravel is the primary source ofmineral aggregate. Almost two-thirds of this aggregate is consumed in the Edmonton and Calgary regions. Sulphur produced at 48 sour gas processing plants and two oil sands plants was valued at $84.8 million in 1997 and accounted for 80% ofCanadian sulphur production. Four companies solution mine the Elk Point salt beds to produce chlor-alkali chemicals, industrial salt and sodium chlorate. Natural brine is also produced as a dust control product. Al $22 million, peat moss is a major industrial mineral product in Alberta. Other minerals with noteworthy production include shale, stone, silica and ammolite. The commodities with the greatest development potential are diamond, silica and oil sands tailings by-product minerals.

Jan 1, 2001

By Jing Chai

The Cenozoic unconsolidated strata with the thickness of 100 to 240m in the east area of China are composed of clay, sandy clay and hardpan, etc. Numerous shafts of the coal mines in these areas have been damaged to various degrees since 1987, with the main reason for this being the subsidence of the super-thick unconsolidated strata. To prevent the continuing settlement deformation of unconsolidated strata caused by groundwater removal, long-term water injection through multiple boreholes controlled the settlement deformation of unconsolidated strata. A new type of fiber Bragg grating (FBG) sensing system was successfully used for real-time strain monitoring of the unconsolidated strata during water injection at a coal mine in China. A mathematical model for the compression settlement induced strain calculation is proposed which can assist understanding of the effect of water injection on the ground. With the increase in water injection, the unconsolidated strata compressed state was improved by the transition of the stress state from compressive to tensile stress. The wavelength change of fiber Bragg grating sensors corresponded with the trend of the water level in the same strata. Engineering practice indicates that these sensors can normally, safely and reliably survive conditions associated with hydrous unconsolidated strata. The FBG sensing can be used for continuous lifetime monitoring of the system, starting with real-time monitoring during low-pressure water injection process of multi-borehole. The results will give important guidance for water injection and mastering stratum subsidence.

Aug 1, 2013

By D. J. Wesolowski, D. A. Palmer, P. Bénézeth, S. Hilic

The equilibrium solubilities of gibbsite, Al(OH)3, and boehmite, A1OOH, have been extensively studied in our laboratory from 30 to 90°C, and 100 to 300°C, respectively, to ionic strengths of 5 mol.kg-1 (NaC1) over a wide range of pH. The resulting solubility constants have been treated with consistent empirical models that incorporate appropriate experimental data taken from the literature. These studies were initiated in part to understand and quantify scale formation in geothermal fields as a result of fluid re-injection from electric power generating plants. Most of the experimental results were obtained through application of a unique potentiometric method that allows for rapid, precise measurement of the in situ pH and allows the approach to equilibrium to be monitored from under- and super-saturation. The experimental program was extended to deal with more basic solutions (e.g., five molal NaOH), in which the dissolution of boehmite was measured for application to the refining of bauxite by the Bayer process. More recent results in strong caustic solutions at temperatures below 90°C were obtained to investigate the dissolution of aluminum-containing sludge from holding tanks at the Savannah River waste reprocessing site. In this case the solubility enhancing effects (kinetic and equilibrium) of triethanolamine were also established and quantified. Finally, potentiometric solubility experiments were conducted (50°C in 0.l mol-kg-1, NaCl) on aluminum alloy sheets to identify mainly the nature of the aluminum oxide/hydroxide surface layer formed under these conditions.

Jan 1, 2004