Search Documents

By J. Dilbeck, J. K. Ratliff, T. Petrov, Z. Brown

"In efforts to improve dust control during deep cut continuous mining a supplemental atomizing spray system, mounted on 14CM15 continuous miner, has been designed and successfully implemented in a U.S. coal mine. The mine is 2.1 m (7-ft) high and uses a blowing curtain face ventilation system with 1.1 m (3.5-ft) curtain offset from the rib. The face ventilation design parameters were set to 9.4 m3/s (20,000-cfm); 4.2 m3/s (9,000-cfm) line curtain flow rate, and 3.8 m3/s (8,000-cfm) scrubber capacity. The performed in-mine measurements, before and after the implementation of the atomizing spray system, showed a significant decrease in the respirable dust levels at the operator place as well as at the return. The paper describes the supplemental water spray system design and performance supported by three-dimensional computational fluid dynamics (CFD) simulations and in-mine test data.INTRODUCTIONThe work on this project have started in 2015 with a study of the conventionally applied face ventilation layouts. The specific behaviour of the face ventilation system have been analyzed trough in-mine measurements and computer modeling of typical cut scenarios. An computer modeling methodology have been developed for estimation the respirable dust concentration (RDC) using tracer gas to RDC contour mapping, calibrated by a single point value, provided by in-mine measurement. Utilizing the results of this study the engineering staff of the mine designed and implemented a supplemental atomizing spray system to improve the dust control during the deep cut continuous mining. Today the atomized spray system is successfully applied demonstrating steady performance and a significant decrease in respirable dust concentration on the working places of the continuous miner (CM) and coal transporters (CT) operators as well as at the return air stream. Information about the applied type of spray nozzles provided by other researchers (Cheng, 1973; Dick et al., 1996; Organiscak & Page, 1998; Pollock & Organiscak, 2007) and spray system manufacturers (Spraying System Co, 2011–2018; Steinen Mfg., 2016) have been used in this project. CFD code and simulation approach validated in a study conducted in 2000-2014 have been applied (Turner et al., 2002; Wala et al., 2004, 2007; Petrov, 2014)."

Jan 1, 2019

By A. O. Dufresne

WITHOUT transportation, mining would be quite impossible. Any person familiar with the operation of a mine knows full well that from the minute ore is blasted, it is kept moving until it reaches the treatment plant. In the mill, by means of conveyors and elevators, the ore is brought from receiving bins to one machine after another until finally its valuable mineral is separated from the gangue. The finished product must then be shipped -either by boat, rail, or motor trucks to industrial centres, where it undergoes further treatment and transformation into finished commercial goods. Everybody appreciates that the winning of an or-e includes, amongst various operations, the moving of large quantities of material of generally low value. Transportation, therefore, must be considered One of the most important factors in the economics of mining. My assignment, this afternoon, is not to treat of that phase of transportation as it directly affects mining operations, but rather to consider some of the aspects of overland transportation and its influence in bringing about the development of mining camps in Canada. I shall take the liberty of rapidly surveying conditions facing prospectors, mine developers and operators from the time a region is still in a pre-pioneering stage until such time as a mine starts shipping its concentrates.

Jan 1, 1956

By A. Desbiens, R. del Villar

"This two-part paper summarizes the design and implementation of a distributed PIbased control strategy installed at the B grinding circuit, at the Kidd Creek Division of Falconbridge Ltd. Part I details the design of the control strategy using a grinding circuit dynamic simulator (DYNAFRAG). The first step consisted of sampling campaigns and data processing to calibrate DYNAFRAG. Then, several control alternatives were designed and tested with the simulator. The main feature of these strategies is their ability to regulate or keep within an upper and lower limit five output variables (circulating load, rod mill density, cyclone feed and overflow densities and pump box level) with only three manipulated variables (rod mill water, pump box water and rod mill tonnage). By simulation on DYNAFRAG, it was possible to discriminate among several control structures. The preferred control strategy uses a saturation algorithm, which allows the adequate regulation of two measured variables with only one actuator. Controllers located in interacting loops are appropriately tuned, taking into account the existing process coupling. Part II will present the implementation of the selected control strategy.IntroductionSteady state simulators are used to predict the stationary state of a given process under specific operating conditions. Tradi - tionally, steady state simulation has been applied for process flowsheet design, for evaluating process modification benefits or for determining key operating parameters in process operation optimization. Dynamic simulators add a new dimension to process simulation since they allow the prediction of the process transient behaviour, resulting from the application of a different set of operating conditions and/or from natural disturbances or equipment failure. Dynamic simulators can also be used for the training of new operators or for the design of control strategies."

Jan 1, 1997

By A. Rousselet, H. Gilbert-Tremblay, A. Berton

"Robex Resources interrupted production at the Nampala Mine in September 2014 following throughput and gold recovery results which were below expectations during the first months of operation. After a thorough plant audit, an important brainstorming took place in order to identify an economical path to resume production. It was clearly identified that a significant investment was necessary at the concentrator prior to restarting the plant, namely the addition of a ball mill and a new elution system.The mineral processing simulation software USIM PAC was used in order to simulate the grinding circuit in design. The simulations’ outputs allowed the ball mill characteristics and the surrounding classification devices to be designed with more accuracy. Many ball mills available from second hand retailers were therefore studied in the simulated circuit. The chosen ball mill, which was in perfect condition, had the advantage of being available for rapid delivery on site.The paper first describes the ball mill sizing method in comparison with the conventional Allis Chalmers method. It then describes the phase 2 concentrator start-up (that took place in 2016) with the commissioning of the ball mill, the classification circuit, the gravity concentration, the four (4) new carbon-in-leach (CIL) tanks, and the Zadra elution system (The phase 1 start-up took place in 2014). It finally provides production data compared to expected simulation data, as commercial production was reached in January 2017.IntroductionDesigning a new concentrator or new equipment within an existing concentrator requires significant efforts to identify possible bottlenecks and their causes (i.e. limiting equipment or sectors) and accurate sizing of major equipment can have a tremendous impact on the economy of the whole project. In the presented case study, the ball mill was the critical equipment and oversizing it could have brought the Capex to a level where the project would not have gone through. Inversely, undersizing the mill could have resulted in lower production and therefore no economic viability for the project once it is in operation.During engineering studies, equipment sizing often relies on a static mass balance and one-by-one sizing of all pieces of equipment. The sizing is then left to the equipment manufacturer or in the case of mills, evaluated with empirical models mostly relying on the Bond equations (Allis Chalmers method) [Rowland and Kjos, 1978]. This methodology shows the disadvantage of not considering interaction between equipment in a mineral processing circuit, especially when recirculation occurs. Also, it has the disadvantage of not using the more advanced grinding models that include the use of the whole particle size distribution as well as phenomenological components by only using limited parameters in the ore particle size distribution (i.e. the P80). This can be explained by the lack of data that sometimes needs to be gathered in order to tune the more advanced models but also by the conservative mindset in mineral concentration engineering which does not always favor the use of process simulation. In many aspects of process engineering, Soutex has demonstrated its affinity to using simulation in order to size equipment with more accuracy, consider process variability, simulate complex systems, and study supply chain management (Berton et al., 2015)."

Jan 1, 2018

By Frank Otten, Jochen Greinacher

"In July 2017, Deilmann-Haniel signed a contract with IOO Slavkaliy to sink two 750 metre (m) deep freeze shafts for the Nezhinsky Potash mine in Belarus. This is the second shaft project where this technology is employed after two over 1,000 m deep shafts for a potash project in Saskatchewan, Canada, have been sunk by the application of the Herrenknecht Shaft Boring Roadheader (SBR) technology. Developed to sink shafts for green field projects in soft to medium hard rock, in frozen or unfrozen geology, the machine technology utilizes a roadheader-type cutterhead on a telescopic boom to mechanically excavate the rock, and a pneumatic mucking system to convey the muck from the face into the buckets. This leads to a manless face during the sinking cycle and thus a significant improvement in terms of workplace safety. For the Nezhinsky project, the SBR design was significantly modified in close cooperation between Deilmann-Haniel and Herrenknecht, based on the available experience and the special requirements of the project. Such modifications have been for example the adaptation of the Pneumatic Mucking System to cope with wet material as well as dry as originally planned or the shaft lining moving from shotcrete application to jump for and tubbing installation for which a step-change hands-off tubbing erector for the placement of segments was designed. Further modifications to optimize the machine technology for the requirements during shaft sinking were applied on the two machines for the Slavkaliy project as well as several revisions to match the special project requirements. The SBR is suitable for soft and medium hard rock up to 100 MPa UCS. The main design limits are maximum weight of the machine with 400 tonnes and length or height of 50 m due to the depth of the pre-sink. The Pneumatic Mucking System was changed in all components, sheaves and rope arrangement were redesigned and the concept of the hoist system was also re-engineered. The SBR in Belarus is configured for a daily sinking rate of three metres and all systems behind the cutting boom are not the bottle neck of the whole system. The works on site started in November 2017 including freeze hole drilling, construction works, site setup, installation of hoists winches, permanent headgears and other components required for sinking. The SBRs arrived on site in June/July 2018 and were preassembled on surface and then lowered into the 50 m pre-sink. SBR #1 started full face sinking in mid-December 2018, and SBR #2 in late January 2019. By the end of February 2019, the machines were at 150 m and 100 m depth respectively, and achieved up to 3.6 m/day concrete lined shaft. The SBR and the sinking system, the experiences, problems, technical solutions and performances of this challenging project will be presented in this paper."

Jan 1, 2019

By R. C. E. Bray, Peter Price

"The property of Pamour Porcupine Mines, Limited, is in the eastern Porcupine area, about 12 miles northeast of Timmins. It covers parts of lots 3-6 (inclusive), cons. 5 and 6, Whitney tp., Cochrane district, Ontario. It is an amalgamation of the old La Palme, Three Nations, and Porcupine Grande properties.The first discovery on the Pamour was made in 1911. During 1911 to 1914 a small shaft was sunk on the Three Nations vein to the 200-foot level and a 100-ton stamp mill was put in operation, but only a small production was achieved. The property remained idle from 1914 to 1923. In 1924 some diamond drilling was done along the Keewatin-Timiskaming contact with some encouraging results, but the gold mineralization encountered was too low in general at the price of gold then prevailing to warrant further · work. The increase in the price of gold revived interest in the area, and the above noted amalgamation was effected in 1934. Options were taken and successively dropped by two large mining companies. Following this, exploration both on the surface and underground was started by Quebec Gold Mining Corporation, Limited. Diamond drilling in the early part of 1933 showed considerable ore in conglomerate and greywacke to the east. In the middle of 1935 Noranda Mines, Limited, assumed control and management. A new shaft was sunk and the property was ·equipped with a mill having an initial capacity of750 tons a day. This was subsequently enlarged to 1,500 tons a day.From the commencement of milling (May 16, 1936) to the end of 1946, 5,025,545 tons of ore having an average grade of 0.1327 oz. a ton ($4.64 at $35 an oz.) have been mined and milled."

Jan 1, 1954

By F. A. Auld

"Traditionally deep shaft sinking from the ground surface was carried out using drill and blast methods. Although large diameter blind shaft drilling has been carried out successfully on numerous occasions previously, including as early as 1852 in Germany (Auld, 1995), little attempt has been made until more recently to mechanise the shaft sinking excavation process using down-the-hole machines. This paper reviews the development of deep shaft sinking machines from the early 1970’s up to the present day. INTRODUCTION Mechanical excavation methods can significantly improve excavation performance, in order to access natural resources faster, and labour safety is increased compared to drill and blast operations. However, shaft sinking machines need to be capable of accommodating all the basic requirements for deep shaft sinking, namely: 1. Excavation and muck removal 2. Ground stability control 3. Groundwater ingress control 4. Temporary lining installation 5. Permanent lining installation and watertight sealing 6. Ventilation 7. Secondary means of egress for personnel In addition, how the machine operates in the shaft is an important factor, either slung on ropes from a surface headgear or on its own in the bottom of the shaft. An all-embracing machine which can deal with all of the above conditions is impossible but many of these requirements can be incorporated into a single machine. Deep shaft sinking also differs greatly from normal tunnel construction which employs the use of either a roadheader arm installed within a shield or a full-face tunnelling machine for excavation. Hydrostatic pressure and ground stability problems increase with depth, whereas in tunnelling the depth is normally relatively shallow and the aforementioned factors remain approximately constant along the tunnel length. DEEP SHAFT SINKING MACHINES All the shaft sinking carried out previously in the UK was by the traditional method of drill and blast. Elsewhere, in other parts of the world, attempts have been made to mechanise the process."

Jan 1, 2019

By P. J. Routledge

THE purpose of this paper is to discuss the practical aspects of locating gravel deposits and of establishing efficient, portable concrete aggregate beneficiation plants for use on construction projects where limited amounts of high-quality gravel and sand are required. Certain projects are listed, in order to demonstrate the wide variety of problems encountered. Routledge Gravel Contractors Limited, North Vancouver, have supplied concrete aggregate for construction projects in British Colum-bia since 1957. In tl1at year, in sup-plying aggregate for a small project at a site on the northern coast of British Columbia, our quote was as follows: Concrete aggregate to specifications, f.o.b. scow, North Vancouver$ 1.75 per cu. yd. Scowing charges to site. $16.00 per cu. yd. At that time, our company realized that more attractive quotations could be submitted if local gravel was utilized where available. Port-able equipment was then acquired and a simple screening plant (Figures 1 and 1a) was at first used. This was later replaced by heavier, more versatile equipment. The use of suitable equipment, the keeping of cartage to a mini-

Jan 1, 1962

By J. Guha, D. Racicot, S. Peloquin, F. Lange-Brard, S. Bureau, A. Tremblay

The Devlin copper deposit consists of a flat-lying vein and a network of steeply dipping mineralized veinlets hosted by leucotonalite of the Chibougamau Pluton. Most of the vein is enclosed in a hydrothermal breccia zone which has been superimposed on a primary igneous breccia formed during the emplacement of the leucotonalite unit. This igneous breccia contains cognate fragments as well as fragments of the Dore Lake Complex, host rock to the pluton, set in a leucotonalite matrix. The hydrothermal breccia is formed of fragments of leucotonalite and the earlier breccia set in a matrix of finely comminuted rock variously altered in a roughly zonal arrangement. The major ore-bearing structure is the tabular flat-lying vein, varying in thickness from 10 centimetres to 1 metre, with a slight dip to the northeast. Well developed fracture planes, in four major orientations, contain both sulphides and gangue minerals. These appear to be displaced by the flat-lying vein. Late movements affecting the deposit include minor vertical displacements and an east-west shear truncating the southern edge of the vein. Widespread selective alteration of the leucotonalite, followed by multiple alteration veining stages characterize the deposit. Fluid inclusions associated with the mineralization indicate low temperatures, variable salinities with a variety of daughter minerals, and a vapour dominated phase. The fluid shows evidences of boiling at shallow depths. The sequence of events envisaged for the Devlin deposit is a primary brecciation during emplacement of the leucotonalite unit with widespread selective alteration possibly during the cooling stages followed by hydrothermal brecciation and late stage fract uring producing the vertical fractures and the flat-lying vein. From the alteration characteristics and the fluid data it is inferred that the Devlin deposit is the near-surface expression of a porphyry system.

Jan 1, 1984

By K. Harris, J. B. Wahl

Ni-base superalloy cast materials provide an outstanding balance of high temperature strength, fatigue resistance, oxidation resistance and coating performance and can be produced to very tight tolerances in extremely complex configurations, such as axial and centrifugal integral cast turbine wheels. As a result, cast superalloys are used in the most demanding applications of aero and industrial gas turbine engines. Use of these materials is expanding to smaller microturbine, turbojet, turbocharger and missile engine applications due to this unique combination of desirable properties. This paper will present an overview of the application of investment cast Ni-base superalloys and process capability to small turbine and missile engines.

Jan 1, 2010

By W. G. Stevenson

With the author's background of extensive experience, this paper delineates the role of the prospector in modern-day exploration programs. The stages in the development of a prospect to a producing mineral district are outlined, and examples are given from the Ross River area of the Yukon Territory and the Peachland and Highland Valley areas of British Columbia.

Jan 1, 1970

By Cheowchan Leelasukseree

Mae Moh mine, operated by Electricity Generation Authority of Thailand (EGAT), is the largest open pit mine in Southeast Asia. Its production is approximately 15 million lignite tons and 90 million m3 of waste, annually. The bottom of the final pit limit is designed to be approximately 500 m in depth. Presently, the pit depth is almost 250 m below original surface. The complexity of geological structures, such as faults, has caused a number of geotechnical difficulties. In a challenging lowwall area, called Area 4.1, an inclined weak bedding plane, G1, will be daylighted along the lowwall as following by mine plans. The dimensions of Area 4.1 are nearly 300 m wide and 90 m high. The friction and dip angles of the G1 interface are reportedly 12° and 15°, respectively. A three million m3 claystone block, resting above G1, would potentially slide down, and possibly cause a massive failure. EGAT engineers are acutely aware of the potential gigantic sliding failure and are modifying the mine plan in Area 4.1 to improve mine safety and minimize the displacement of the potential sliding block, reduce the possibility of failure and lower the additional mining cost as much as possible. The cut and fill mining technique was selected and studied to achieve those goals for mining in Area 4.1. With this mining technique, G1 will be partially daylighted. Therefore, an arch formation is induced with a sliding block above the mining area, which could perform as a temporary support undercutting a certain span. Initial studies of the behavior of the partially undercut slope are presented in this paper, along with a review of the similar failure history in Mae Moh mine and a 3-dimensional numerical model of the mine. The failure history review provides an estimation of undercut span without failure. The three-dimensional numerical model results, using 3DEC, gave an initial approximation of the displacement of the sliding block in Area 4.1. The next exciting study of the behavior of partially undercut slope is a trial undercut slope field experiment in Area 4.1. Currently, a trial undercut slope field experiment in Area 4.1 is under construction. In the field experiment, a number of monitoring programs will be installed in Area 4.1 to monitor and obtain information to allow a better understanding of the behavior.

Jun 1, 2012

By Rolf Andreas Lauten, Yanhong Wang, Yongjun Peng

"In mineral flotation, bentonite as a kind of clay mineral imposes deleterious effects on the flotation of valuable minerals, possibly through its ability to increase the pulp viscosity. A higher viscosity lowers the amount of froth and affects the bubble-particle collision frequency. A previous study found that adding gypsum to a bentonite-ore mixture lowered the viscosity, possibly by inhibiting the formation of interconnected network structures. In this study, sulfate as an anion with different types of cations, Na+, K+, Mg2+ and Ca2+ were used to reduce bentonite viscosity and to improve flotation performance. It was found that at the same concentration, MgSO4 was the most effective salt in reducing bentonite suspension viscosity, while CaSO4 was not as effective likely due to the lower solubility of CaSO4. Na2SO4 and K2SO4 reduced bentonite suspension viscosity at high concentration. Flotation kinetics of ore blended with bentonite was increased with increasing the electrolytes concentration, which generally correlated with the reduction of bentonite viscosity. Meanwhile, significant discrepancies were found between flotation results and rheological measurements in the presence of monovalent ions. It is indicated that the morphology of bentonite aggregates in electrolytes solution is likely to influence the hydrodynamics in the froth zone.INTRODUCTIONClay is present in many ore bodies as a gangue mineral. Presence of clay presents several challenges in the processing of valuable minerals. They are soft compared to valuable minerals, which means that during grinding of the ore, clay particles are likely to obtain a smaller particle size than the valuable mineral. Often clay particles may be within the colloidal size domain (<20 µm). The smaller size increases the probability of entrainment in the concentrate. Another challenge is their anisotropic charge distribution, where depending upon the pH, edges (E) and faces (F) carry charges of opposite sign. This facilitates formation of aggregation structures that may impede percolation of bubbles through a froth, but also increase the viscosity more than expected from the mere change in volume fraction. In addition to lowering the froth mobility, a high slurry viscosity will have implications for the gas dispersion in the flotation column as it affects the dispersion of the suspended particles, and it modifies the bubble-particle collision rate and attachment efficiency (Bakker, Meyer, & Deglon, 2009; Shabalala, Harris, Leal Filho, & Deglon, 2011). A pragmatic approach to this problem is to blend high clay ore with ore of lower clay content, reducing the overall clay concentration. Alternatively, one may lower the solids content of the flotation slurry to counteract the viscosity-building properties of clay. While feasible, this approach has the disadvantage of increasing required flotation volume, and it also affects the properties of the froth. Thus, there are currently limited options in lowering the impact of clays and their tendencies to increase viscosity in flotation slurries."

Jan 1, 2016

By W. M. Goodwin

The gold district of northwestern Quebec, though it has attracted such widespread attention during the past year, is still in the prospect stage throughout, and one must preface any remarks about it with the plain statement that its capacity to produce gold commercially is still subject to proof. However, this proof may be forthcoming any day, and from widely separated localities. Consequently it is of interest to note some of the features of the region and of the prospects now being developed. First I shall note the relation of this mining development to the province of Quebec and to the Dominion; then will follow a brief resume of the known geological facts; and finally I shall describe briefly some of the more advanced prospects developed during the past twelve-month. Those that have followed closely the fortunes of the new gold-field will find little that is new in what follows, but it may serve a useful purpose for others by bringing together scattered items of information and presenting them as a whole. GOLD MINING AND AGRICULTURE First let us consider the gold belt in its relation to the province of Quebec. Apart from the world-renowned asbestos camp south of the St. Lawrence, it is the only mineral development of major importance the province has experienced. It is the first important development in the province&apos;s vast area of Precambrian rocks, most of which remains as yet totally unexplored and unprospected. The relative importance of this first mining camp in northern Quebec cannot as yet be gauged, but it is bound to stimulate an active interest in the other mineral-bearing areas now known to exist, and in the vast unexplored spaces.

Jan 1, 1924

By E. P. Wiechmann, J. A. Henríquez, P. E. Aqueveque, L. G. Muñoz, G. A. Vidal

"The original segmented intercell Optibar succeeded in reducing the magnitude and occurrence of short circuits. It also improved the specific energy consumption of the process. This paper expands the load current source concept introducing a triple segmented bar. This new bar adds immunity to dirt contacts and open circuits. Moreover, it further improves the standard deviation of current densities. As compared with industrial practices this development should accomplish an 8% specific energy reduction. Also, a plant implemented with BBS should be able to work with 12.5% higher process currents than Walker without compromising the operation.INTRODUCTIONIn 2011 the technology based on current mode was implemented at industrial scale. The success of this technology moved CIM Magazine (Lanktree, 2011) to write in the Jan 2012 issue an upfront story of this technological innovation. To cover the story, the technical reporter Graham Langtree was appointed by Peter Braul Editor of the upfront section. The article tells that “More than 40,000 tonnes of copper have been refined in a year-long test run of Optibar Inc.’s new technology at Barrick Gold’s Zaldívar copper plant in northern Chile. The new segmented intercell bars being used in the Compañía Minera Zaldívar refinery have slashed energy costs, reduced short circuits during refining and allowed the production of heftier, purer sheets of copper – gains that all promise to boost the plant’s margins. A copper refining tank house containing the cell circuits typically consumes 2,000 kWh of electricity to produce a single tonne of grade-A copper. Yet, monitoring the energy efficiency of the Optibar technology after increasing the weight of harvested copper sheets, the project’s engineers recorded a 92 kWh-per-tonne cut in energy consumption, a savings of 4.6 per cent. “Today, with the power prices we have, Optibar technology represents a potential savings for the whole plant of US$1.5 million per year,” says Robert Mayne- Nicholls, executive general manager of Barrick Gold’s Chilean operations.”"

Jan 1, 2012

By A. C. Halferdahl

The Granby ores may be divided into three groups or classes. The No. I ore is a heavy pyrite, chalcopyrite, pyrrhotite, sulphide carrying some free silica, and calcite. No. 2 ore carries the same general group of sulphides as does No. 1, but in a lesser amount. The gangue is an altered greenstone. No. 3 ore has a smaller amount of sulphides than either of the others. Analyses of these ores is as follows: Cu. Si02 Fe. CaO S. Al 203 MgO No. I. Per Cent. 1.8 17.5 33.0 5.7 34.5 2.3 1.3 No. 2 Per cent. 2. 0 35. 6 23. 9 4. 3 I .5. 0 9. 2 6 .. 0 No. 3, Per cent. 1 . 5 40. 9 21 . 7 3. 0 I 1 . 3 11 . 0 5 . 4 The sulphide minerals in No. 2 and No. 3 ores occur largely in bands in the gangue, and for these portions comparatively coarse grinding serves to release the gangue. Drill cores show a certain dissemination of sulphides in portions of the rock, so that grinding to 5 per cent. + 65 mesh with 65 per cent.-200 mesh liberates the sulphide minerals very completely. The association of the sulphides is fundamental. The pyrite was probably deposited first and was followed by a portion of the chalcopyrite, or these two portions of the sulphide minerals were deposited together.

Jan 1, 1924

By Balmer Neilly

In these days of arrested prosperity, when patience is tried and the future but dimly outlined, Canada&apos;s gold mining industry stands out as a beacon light shedding its rays of hope and confidence and demonstrating that there is still one product unaffected by Customs barriers and eagerly sought by all the people of the world. Some other forms of industry have hesitated and side-stepped. Some have cried for help, and in spite of public assistance, generously extended, they are still unable to demonstrate definitely their ability to resume the onward march. But gold mining has never hesitated. As an industry, it has bad an unique experience. When prices are high and conditions are generally referred to as prosperous, this industry is adversely affected. The cost of production goes up; profits are diminished; public sympathy is lacking; and, thrown upon its own resources, the industry tightens up its belt and throws its whole energy into an effort to improve operating conditions, and offset high prices by increased efficiency. When, in due course, depression follows inflation and prices ebb, the gold miner, through necessity, finds himself physically and mentally prepared to meet the situation.

Jan 1, 1932

By Kari Niiranen, Andreas Boehm

LKAB (Luossavaara-Kiirunavaara AB) is operating underground iron ore mine, with three beneficiation and pelletizing plants in Kiruna, Northern Sweden. The wet low intensity magnetic separation (WLIMS) is regarded as the crucial part of silicate mineral separation from the ore. The Kiirunavaara iron ore deposit shows a rather low content of silica (ca. 2.3 to 3.3 % SiO2) but the silica grade is expected to increase in the deeper parts of the deposit. This can be problematic in the case of DR pellet quality with an average silica grade under 0.75 % SiO2. A laboratory scale methodology was developed for the systematic characterization of the ore for mineral processing with the focus on silicates at the Institute of Mineral Processing, University of Leoben. This methodology is combining mineralogical, geochemical and process mineralogical characteristics. Automated mineralogy (QEMSCAN) was used to study the modal mineralogy, the distribution of silicate minerals in different particle size classes after comminution, the deportment of silicon (Si) between various silicates and degree of liberation and intergrowth of magnetite and silicates. Based on the mineralogical investigations, actinolite, phlogopite and even quartz and albite are the predominating SiO2 bearing minerals in the ore. The important result of the investigations was the discovery of two separate subtypes within the high silica ore type B2 based on their mineralogy and mineral processing characteristics. The crucial part of the investigations of intergrowths and liberation of magnetite results was the magnetic separation tests carried out with the Davis magnetic tube. The binary intergrowths of magnetite and the silicate minerals (mostly actinolite) are the most common type of mineral association discovered. The significant characteristics in the intergrowths of magnetite and actinolite are the fine-grained magnetite inclusions in actinolite which may end up increasing the SiO2 grade in the magnetite concentrate despite magnetic separation.

Jan 1, 2016

By R. C. Rowe

THIS paper is an endeavour to analyse the ideal and practical functions of government technical mining services, and their relationship to the National Domain, as well as to one another. its spirit is not critical, even though at times it may appear to besoin fact. It is a serious effort to divert a trend in public thought which delights in calling itself practical whereas it is really merely short-sighted. The author refers particularly to the idea that governmental research is a luxury which should be curtailed in the interests of economy, and turned over to private enterprise or the provinces. In order that we obtain the proper perspective of the question, it is advisable to indulge in a little history. In the year 1842, the Geological Survey of Canada was formed under the guidance of William (later Sir William) Edmund Logan. The literature on the founding and history of the Geological Survey of Canada is extensive, and therefore it is unnecessary to go into detail here regarding it. It might be mentioned, however, that the Geological Survey of Canada is only seven years younger than the Geological Survey of Great Britain (founded in 1835), and is only exceeded in age on the American continent by the State Geological Surveys of New York, Pennsylvania, Massachusetts, and Michigan, which were founded between 1833 and 1836. In 1877, the Geological Survey became a permanent government institution as a branch of the Department of the Interior. It should be noted, however, that the Director of the Survey ranked as a Deputy Minister and reported direct to the Minister. This continued until 1907. In 1886, the Mineral Resources and Statistics Division of the Geological Survey was formed. Some years later, the Canadian Institute of Mining and Metallurgy (then the Canadian Mining Institute), backed by the mining press, began to agitate for the establishment of a Dominion Department of Mines, and in 1907 such a department was founded by the Geology and Mines Act of that year, with a separate Cabinet portfolio for the position of Minister of Mines.

Jan 1, 1939

By R. J. T. Charles

Introduction An apparatus that will measure the surface area of a few of the simple minerals with a high degree of accuracy has been described by J. W. Bell (1). His apparatus consisted essentially of a photometric device that would measure the turbidity of fine particle suspensions. Turbidity, in this case, was considered as a function of surface area. Bell&apos;s method of surface area determination seemed to offer possibilities of extension and improvement to the point where it might approach a general method of particle size measurement. Theoretical and Practical Considerations of the Photometric Method In order to illustrate how turbidity may be considered as a function of average particle size, and to indicate the type of results expected from a photometric method of particle size measurement involving turbidity, the following theory may be hypothecated. If a number of particles, considered as spheres of uniform diameter, are placed at random in the path of a beam of light, the following expression, which will give the change in light intensity as a function of the diameter of the particles, the specific gravity of the material, and the weight involved, can be formulated from the Beer-Lambert Law:

Jan 1, 1951