Search Documents

By A. N. Shen

Fe3A1 intermetallics are potential inexpensive candidate for hot applications. In this project, torsion tests on hot-rolled and annealed Fe3A1 (Fe-15.5A1-5.8Cr-1.0Nb¬0.05C) were carried out over the ranges 750-950°C and 0.01~1s-1 . The experimental results showed that when peak stress op>90MPa (LogZ>16s-1 , Z: temperature-compensated strain rate), specimens cracked at randomly low strains. Optical microscopy exhibited original elongated grains and many grain boundary cracks associated with segregation. With op<40MPa (LogZ<16s-&apos;), specimens deformed with low random op but considerably high fracture strains; slowly propagating cracks may explain the reduced flow stress. Optical microscopy showed both elongated grains and equiaxed subgrains with some indications of geometric dynamic recrystallization (gDRX) and of static recrystallization (SRX). Compression tests gave higher stress with little effect of the preexisting cracks. The activation energy Quw of current material in satisfactory torsion and compression tests is about 10% higher than previously published. Fe3A1 has body-centered cubic structure in the experimental range, so it was compared with ferritic stainless steel 434C (Fe- 16.55Cr-0.96Mo-0.21Ni). Constitutive constants and restoration mechanism are compared between these materials. While Fe3A1 is hardly a light metal, it is considerably lighter than most steels. Furthermore, like the other body centered cubic metals (BCC) (a-Fe, ß-Ti, ß-Zr and ß-brass), it exhibits a high degree of dynamic recovery (DRV) like Al alloys, producing easier hot workability than that of austentic stainless steels.

Jan 1, 2007

By G. Grassmück

The question of whether the air curtain principle could be used under conditions prevailing in Canadian metal mines was investigated. A vertical, portable BERRY air curtain was tested, at first in a wind tunnel built at Ecole Polytechnique at full scale (8-by 8-ft cross section) to simulate a drift and its lateral connections, and then in the haulage ways of a metal mine under actual conditions. The results permit us to predict under what conditions this type of air curtain is capable of acting as an air stopping or flow regulator and how it could be further developed.

Jan 1, 1969

By L. S. Beck

"The Athabasca region forms part of the Churchill province of the Canadian Shield and is underlain by an Archean or Aphebian assemblage of rocks that underwent severe metamorphism and granitization during the Hudsonian orogeny (1750-1950 m.y. ago). In places, the eroded orogen is overlain by unmetamorphosed cover rocks (in-cluding the Martin and Athabasca formations) of probable Paleohelikian age. Basic dykes cut all the rocks of the region.There are innumerable vein-type pitchblende deposits and many syngenetic occurrences of uraninite in crystalline basement rocks. Evidence is presented to show that pitch-blende was emplaced during the final stages of the Hud-sonian granitization and followed the crystallization of syngenetic uraninite transitionally. In terms of P-T condi-tions, the pitchblende deposits belong essentially to Lindgren's mesothermal group.Based on the postulated uranium metallogenesis, the possibilities of finding further deposits of pitchblende and other types of uranium deposits are discussed."

Jan 1, 1970

By J. Visman

"SummaryThis paper is presented as part of a programme to show the steps taken by industry and others interested in supplying a solid fuel of constant quality to 'satisfy a consuming market. The paper deals with the general principles underlying quality control in coal preparation plants, namely, constant quality and close adherance to acceptance limits. It also describes how control of ash content is ""generally hampered by the problem of coal sampling .and the long duration of the ash analysis and how these difficulties may be overcome.Quality control can be effected in several ways. Thorough blending wll reduce variations appreciably, except those of long trend. The latter can be detected by automatic sampling and quick ash analysis. At present, under favourable conditions, a system of half-hourly ash determinations with an accuracy of 0.5 to 1.0 per cent can be realized, to the effect that trends with a 'wave length' of more than two hours cu be eliminated within the limits of accuracy of the ash figures. The general solution of the problem is a combination of blending, accurate sampling, quick ash determination, and statistical analysis of the pattern of ash distribution.The use of statistical methods of analysis, such as the t test and F test, is •discussed at some length in order to emphasize the importance of the correct evaluation of observational data if there is to be confidence in the validity of test results.General ConsiderationsCOAL, as a fuel, is too cheap for a long haul across the country. The limiting distance depends on the price of the local competitive fuels, and, as the price depends to a great extent on quality, so does quality, to the same extent, command the market."

Jan 1, 1952

By The Staff

WE were requested to make a digest of our original grinding report, Fine Grinding Investigations at Lake Shore Mines. This digest is much easier to read than the original report, but it lacks the experimental &apos;evidence&apos; found in the first report which, in many cases, is much more interesting and educational than the conclusions derived from it. In the course of rewriting the paper, we noticed several new angles on the test data which had not occurred to us previously. From the data included in the report and other tests not published, calculations were made which indicated a line of new test work. These tests, among other things, more than suggest a technique for designing the length of mills, the position and number of classifiers, and the total loads a mill should carry.

Jan 1, 1941

By R. M. S. Häggblad

The article deals with stabilisation and regeneration of Ce02 and Ce02/Zr02 based Pt water gas shift catalysts, subject to high initial deactivation. The reaction gas species effect on the catalyst deactivation was investigated by H2-TPR. Activity measurements enabled the effect of different promoters, some added to the Ce02 based catalysts and some to the Ce02/Zr02 based Pt catalysts, to be investigated. The catalysts were also characterised by BET and CO-TPR. Deactivated catalysts activity was restored by using various regeneration methods. Of the two selected carriers the Ce02/Zr02 based Pt catalyst showed the highest resilience to deactivation. For the two different carriers, Ce02 and Ce02/Zr02, Wand Re were the best promoters when the catalyst was subject to deactivation. Experiments with Hr TPR indicate a fast initial change in the platinum oxides concentration and composition. The CO-TPR was used to make conclusions about the various regeneration effects of water and oxygen on the catalyst. Finally it is suggested that not one deactivation mechanism is possible and which mechanism that dominates is dependant on the catalyst and the reaction gas composition.

Jan 1, 2005

By D. A. Karvonen

In 1970, the Government of Saskatchewan instituted a program aimed at resolving the dilemma of excess productive capacity over the market demand which existed for potash produced in Saskatchewan. The two primary elements of the program were prorationing of potash production to market demand and a minimum selling price. The paper reviews the factors, both local and international in nature that led to the introduction of the program. The licensing mechanics and the operation of the program, along with the changes that have been introduced in two and one-half years of operation, are discussed. Attention is given to the results of the controls as they affect the industry and the province. Also discussed is the outlook for Saskatchewan potash in world markets.

Jan 1, 1973

By L. H. Van Loon

INTRODUCTION THE property of Madsen Red Lake Gold Mines, Limited lies between Russet and Faulkenham lakes in Baird and Heyson townships, district of Patricia, Ontario. It is about six miles south west of the town of Red Lake, with which it is connected by an all-weather road. All orebodies found to date at the property are silicified lenticular bodies which lie within tuff beds. The ore bas a specific gravity of 2.95. It consists of mica and chlorite schist, silicified and containing a considerable amount of disseminated carbonate, and mineralized with pyrite, pyrrhotite, magnetite, arsenopyrite, and chalcopyrite. Of these, pyrite, in coarse to fine disseminated grains, is by far the most abundant. Pyrrhotite occurs in ?the gangue material as medium to fine disseminated grains. A very small amount of arsenopyrite, in small crystals, is associated with the pyrite, and small grains of chalcopyrite occur in both gangue and pyrite. Although some of the gold present in the ore is quite coarse, a good deal of it is extremely fine.

Jan 1, 1951

By J Zhou

Based on the mineralogical characteristics and mineral processing techniques required, gold ores can be classified into 12 types, including gold placers, quartz vein-lode ores, oxidized ores, silver-rich ores, iron oxide copper gold ores, porphyry copper gold ores, iron sulphide ores, arsenic sulphide ores, antimony sulphide ores, bismuth sulphide ores, telluride ores and carbonaceous sulphide ores. The bulk mineralogy and gold deportment of each ore type is different and may have a significant impact on ore processing and metal extraction. This paper summarizes the bulk mineralogy and gold deportment in some major types of gold ores and discusses the potential impact of gold deportment on gold metallurgy.

Jan 1, 2011

By D. Fodor

In Romania, there are significant lignite and brown coal reserves hosted by different regions of the country. The most important lignite bearing zone of the country situated in the North ? West part of Oltenia region and which covers a surface area of 2,500 km2 and host a total reserve of 3.0 billion tons of lignite, of which more than 95% can be exploited by open cast method. The paper deals with the existing geological and mining conditions of the zone , the distribution by mining basins and exploitation perimeters, the open cast working technologies and the economic outcomes obtained throughout the time. Years ago, for the improvement of the economic situation as a whole and in each unit, a large production reorganization, technology update and modernization process was started up. There are described the rehabilitation measures of the technological lines and modernization of the equipments of the production flow-sheet, measures developed at present, too and which will still continue in future. There are mentioned the equipments considered, the components under modernization and the economic outcomes obtained so far. At the end of the paper there are presented the future actions for the equipment modernization and perspectives of the lignite deposit exploitation to meet the national economy requirements of solid fuels.

Aug 1, 2013

By W. Mueller, M. Rocheleau, E. Dimroth

The paleogeographic evolution of the Abitibi Belt is subdivided into three phases, namely: 1) a phase of the growth of a submarine volcanic chain, 2) a phase of the emergence and growth of volcanic islands and 3) a phase of uplif t and erosion of volcanic islands. Isostatic calculations suggest that the volcanic sequence in the south of the Abitibi Belt rests on oceanic basement or on the mantle; the volcanic sequence in the north of the belt rests on about 13-14 km of tonalitic basement. 10-15 km of plutonic material accreted to the volcanic islands during paleogeographic phases 1 and 2, and caused the uplif t during paleogeographic phase 3.

Jan 1, 1984

By Tadeusz W. Wlodek

THE known phenomenon that a test-piece of ferro-magnetic steel is magnetic after it has been broken in tension indicates that, while it is being loaded, the steel acquires magnetic properties. In the present investigation of the influence of the stress on the magnetic flux, repeated pulsating stresses of increasing amplitude, varying from zero to the maximum tensile value, i.e., pull-pull loading, were employed. The specimens were prepared from two types of carbon steel and two of alloy steel. The magnitude of the magnetic flux was determined indirectly. The voltage and mode of variation of the electromotive force induced in a coil surrounding the stressed steel specimen were measured as an indication of the varying magnetic flux within the specimen. Curves representing the electromotive force induced by the varying magnetic flux show that as the tensile load increased so also the magnetic flux increased, with a corresponding increase in measured e.m.f. At a certain stress there is a sharp bend in the voltage curve (point Win the diagram, Figure 5); this critical stress corresponds very closely with the yield stress (0.2 per cent permanent strain). Beyond this point, slight increases in the stress produce large increases in the voltage. The wave form of the e.m.f. was registered on an oscillograph. Analysis of the curves so obtained demonstrated the necessity of continuing these experiments, in order to determine the type of induced wave form associated with various types and amplitudes of stresses. In these experiments, the shape of the stress wave was sinusoidal, although the shape of the induced e.m.f. was sinusoidal only up to a certain load and became more and more complex above this load.

Jan 1, 1944

By A. Roy MacLean

"Cape Breton is an island on the eastern extremity of Nova Scotia, Canada. Here, coal mining under the Atlantic Ocean has been a way of life since the early French militia mined coal for heating purposes in 1720. Despite many ups and downs over the intervening years, the coal industry has survived and is now in a favourable position to benefit from the upswing in international coal usage.Mining in Cape Breton Early mining in Cape Breton was done by hand picks and shovels. The coal was loaded into mine cars which were hauled by horses to the main haulage system for transport to surface. Later, compressed-air cutting machines and drills led to the use of explosives to blast the coal so that it could be loaded by hand and transported as above. In 1923, longwall mining (by hand) was introduced. In 1950, the Dominion Coal Company developed the Dosco continuous miner in order to mechanize the longwall coal-getting operation. At this time, conveyor belts came into wide-spread use, along with diesel locomotives to haul mine cars from the longwall face to the main transport system. During this period, coal was also mined by conventional mechanized room-and-pillar equipment such as cutting machines, loaders, roof bolters, etc. This system evolved into the use of the continuous ·miners of today, which are employed in the Lingan Mine room-and-pillar section. However, this method is only satisfactory at shallow depths and gradients. For these reasons, almost all the coal in this coal field will be mined by longwall methods. In 1968, the Government of Canada expropriated the assets of the Dominion Coal Company on Cape Breton Island in order to prevent complete closure of an uneconomic industry by its owners. The government created, by an Act of Parliament, the Cape Breton Development Corporation which now operates the coal mines, coal preparation plants, railway, shipping pier and ancillary services (Fig. 2). Since its inception, the Corporation has closed three mines, opened two new mines, is in the process of developing a third new mine, and has invested heavily in the one mine which remains from its previous owners."

Jan 1, 1985

By Sergio Cattalanl, Francis Chartrand

"The geology and origins of volcanogenic massive sulfide (VMS) deposits in the Abitibi belt of northwestern Quebec have been the subject of discussion since the discovery of the Horne orebodies in Noranda in 1923.The present Noranda version of the VMS model characterizes the ideal deposit as a stratabound, base-metal accumulation that is in close spatial relationship with hydrothermal alteration and stockwork zones, felsic lava domes, coarse phreatic-pyroclastic breccias, and subvolcanic intrusions that characterize vent- and proximal{acies submarine volcanic environments. Deposits tend to occur in a favorable stratigraphic interval within a mining camp, and this is well-documented in the Rouyn-Noranda and Matagami camps.However, in recent years many VMS deposits have been shown to deviate from the ideal Noranda-type. For example, the Ansi/ deposit is characterized by sulphide-bearing alteration zones that extend far above the massive sulfide lenses, and by abundant magnetite immediately underlying massive sulfide. The Horne deposit appears to lack the typical chloritic alteration pipe underlying the massive sulfide lenses, as well as laterally-equivalent exhalite horizons. The Horne and Quemont deposits, besides being the two giants of the camp, are particularly rich in gold, whereas others, such as WaiteAmulet and Millenbach, have low gold values. Finally, some deposits in the Noranda camp, such as the Ansil, Corbet and Mobrun mines, are outside the favorable stratigraphic interval. Therefore, it would appear that part of the key to renewing base metal reserves in northwestern Quebec is the use of evolving descriptive-genetic models that incorporate geological variations like those cited above."

Jan 1, 1990

The topic of the relationships between energy and particle size has had two very active periods -the first in the early thirties, when the relative merits of Rittinger&apos;s and Kick&apos;s proposals were vigorously debated; the second in the early fifties, when Bond&apos;s Third Theory was published. This second stage has produced several contributions that have provided a clearer picture of energy /size correlations in comminution. Derivations of a general relationship have been made from single-fracture experiments and from the rate of comminution, and both methods arrive at an equation of the type E = AK-11? The constant A in the equation may be regarded as a grindability parameter. In some respects, an understanding of the phenomena associated with comminution is still lacking, and research in this field should therefore be expanded. T HE SEARCH for a relationship between the energy consumed in comminution and the size of the broken product has been long and varied, and many

Jan 1, 1964

By L. Rodd, C. Walker, T. Koehler

"The energy content of slag represents approximately 80% of the total energy inputs to a laterite nickel electric smelting furnace. Conventional slag handling methods produce only low grade heat and the entire thermal content of the slag is wasted. A heat recovery system proven on BOF slag in the mid 1980&apos;s can be adapted to a laterite nickel rotary kiln electric furnace (RKEF) plant. Slag is granulated using a high velocity air jet inside a waste heat boiler to produce slag granules. Granules are cooled during flight via radiation to water-cooled boiler walls and by convection to the granulation air. This system has the potential to recover 80% of the total slag energy in the form of hot air and steam.Integration of the recovered slag energy into the RKEF smelter can be achieved by a number of methods, including the use of preheated air at the ore dryers, kiln or existing power plant. Energy from the slag boiler may be used to reheat boiler feed water from the power plant or to produce superheated steam and generate electricity. The heat recovery system can provide up to 25 - 30% of the total electrical requirement of each RKEF line and a reduction in CO2 emissions of 234,000 tonnes per year.The total cost of slag heat recovery, including CAPEX and OPEX, is $2.5/GJ, which is competitive with using coal when CO2 credits are $18 per tonne. With Clean Development Mechanism (CDM) carbon credits currently selling at €13 ($20 USD) per tonne CO2, there is considerable opportunity for slag producers in regions including South America, Korea, Indonesia and Africa. Increasing fuel costs and more wide-spread legislation for GHG emissions will likely create conditions in which slag heat recovery could generate a favourable return on investment."

Jan 1, 2010

By A. G. Darnley

"The Geological Survey of Canada is devoting consider-able effort to finding ways to make airborne radiometric measurements both quantitative and reproducible. Equipment has been designed by Atomic Energy of Canada Ltd. to provide high count rates in order to minimize statistical uncertainty, this being essential to justify applying terrain clearance and Compton scattering corrections to the data. Correction factors have been determined experimentally and can be applied automatically. Considerable ground work has been undertaken in parallel with equip-ment development in order to determine field parameters.Two airborne gamma-ray spectrometers are described. One is based on three 5-by 5-inch Nal(Tl) detector crystals and is used in a helicopter; the other employs twelve 9-by 9-inch detectors and is used from a Skyvan aircraft. The former is being used to investigate the range of radiometric response from specific rock types, and for the correlation of ground and air measurements; the latter has completed initial trials and will be commencing experimental surveys during 1969.Results are given to show the comparative sensitivities of the various detector sizes, and operational requirements for a gamma-ray spectrometer survey are discussed briefly."

Jan 1, 1970

By S. Utili

"The optimal profile of a rock slope under given geometry constraint is investigated by means of the upper bound method of limit analysis. The optimal condition corresponds to maximizing stability factor. It is assumed that rock failure condition is suitably described by the Hoek-Brown criterion. Genetic algorithm is applied for locating the optimal profile. The optimal profiles turn out to be concave profiles but there are heaps around the toes of the slopes. Compared with plane profiles, the percentage of increase in stability factor can reach up to nearly 50%. The key geometry parameters of the optimal profiles are provided for practical use. The new upper bound formulation is capable of computing the stability factors of slopes of any shape, thus the stability status of a slope under man-made excavation can be monitored during the whole construction period.INTRODUCTIONIn mining industry, man-made slopes are excavated to create working surfaces. It is important to optimize the slope profile in order to maximize slope stability under certain geometry constraint. For instance, when the height and width of an excavation are assigned, a plane profile AC (see in Fig. 1) is widely applied in engineering practice, but it has been proved not the best one in terms of safety (Utili & Nova, 2007; Cala, 2007). A vertical profile ABC is the one with least stability. Thus, it can be deduced that there is a profile within the domain of the rectangle ABCD providing the highest stability. Cala (2007) compared the difference of convex and concave profiles in stability using strength reduction technique. According to Cala (2007), circular concave slopes can increase the maximum slope inclination under given factor of safety. Besides, based on upper bound theory of limit analysis, Utili & Nova (2007) assumed a logarithmic spiral profile to prove it is more stable than a plane profile in terms of the stability factor. Although the above studies attempted to seek the best circular or logarithmic spiral profiles, none of them considered the arbitrary shape of the optimal profile and its contribution to enhance slope stability."

Jan 1, 2015

By R. M. BUCHANAN

The segment of Canadian industry based on smelting of alum in um and manufacture of consumer products is based entirely on imported alumina and bauxite. In the absence of Canadian bauxite deposits, consideration of anorthosite, a less desirable aluminous rock, is being undertaken as one alternative in maintaining assurance of supply. Anorthosites in Canada cover many thousands of square kilometres of the Precambrian Shield. Although compositions vary widely among Canadian anorthosites, many appear to exceed the specified minimum of 25% A I 20 3 in bodies containing more than the required JOO million tonnes. A lthough most Canadian anorthosites are of Precambrian age, one located in British Columbia has been identified as being Middle _Cretaceous.

Jan 1, 1984

By C. Edwards

ABSTRACT The versatility and specificity of rare earth elements (REEs) have led to their use in an everincreasing variety of applications in new technologies; consequently, demand for REEs has increased significantly. However, separating REEs safely and effectively is a complex and expensive process. This paper presents a review of REE mineral processing technologies, providing an update on current capabilities in REE mineral processing and REE extraction from the major commercially valuable REEbearing minerals such as bastnaesite, monazite, and xenotime, as well as the ion-absorption type of REE deposits.

Jan 1, 2013