Search Documents

By F. R. Jones, B. W. Taylor, A. R. MacPherson, L. J. Lamb

"The Lake St. Joseph Iron Deposit is in Northwestern Ontario. Exploration to date by Steep Rock Iron Mines Limited has indicated an ore reserve of 683 million long tons. Metallurgical investigations have proved that suitable oxide pellets and/or superconcentrates can be economically produced from this ore. Studies of the Lake St. Joseph iron ore deposits have covered the period 1956-71, and have embodied applications of the improvement in mining and processing technology over this period. Market demand in the early 1960's for high-grade oxide pellets as a replacement for natural iron ores for the blast furnace first drew attention to the potential of the Lake St. Joseph deposit. The current market trend toward utilization of sponge iron to replace steel scrap as feed to electric furnaces and cupolas now suggests that the deposit can better be exploited as a prime source of superconcentrates."

Jan 1, 1972

By J. E. Williamson

Introduction 1. Factors on Which the Design of the Roaster Plant was Based The roasting operation at Lake Shore, it was realized from the outset, would be profitable only if costs and losses could be reduced to a low figure. It was absolutely imperative that the operation should be self roasting over the whole range of tonnages and sulphur grades which might obtain during the life of the mine. The roasting operation could not bear the cost in fuel and labour of even a partially fired roast. To meet this requirement, it was necessary to resort to additional insulation in the construction of the roaster and to provide a more flexible means of rabble cooling than the conventional water jacket (see p. 31). A second basic consideration was that of handling a wet, putty-like concentrate. The operating costs of a drier ruled out the possibility of drying the charge before feeding it to the roaster. Moreover, the dusting which would result from charging a dry product virtually all -40 micron (325 mesh) in size would seriously handicap the use of a dryer. Dust lubrication (p. 3S) due to the back-mixing action of the Edwards rabbles, and the use of a Sullivan slapper ( p. 27) on the concentrate filter, completely solved the problem of handling the roast feed. The third consideration was the reduction of dusting to a sufficiently low point that a Cottrell or other dust collecting system was unnecessary. The Edwards roaster when properly supervised, it is believed, can be operated to give the minimum possible dusting. At Lake Shore, the evidence has been that less than 1 per cent dusting occurs at any time and that the greater part of the dust produced is recovered either in the spray tower or in the dust chambers.

Jan 1, 1947

By K. C. Lahiri, H. P. Das, G. G. Sarkar

"The petrographic components of any particular rank of coal often show some distinct physical and chemical characteristics. Therefore, their pro-portionate distribution in a coal greatly influences the technological behaviour of the coal.In any size or gravity separation of a coal, the petrographic constituents become segregated to different degrees in some preferred size or specific gravity range. Therefore, a knowledge of the petrographic nature of the washed and/or screened fractions is often considered essential in selecting the most efficient method for coal preparation and in exploring the proper evenues for its utilization.A graphical method is described in this paper to indicate the mineral-matter content and the petrographic components of the washed fractions of a coal at different ash levels of separation in the form of a new washability diagram. This diagram can be conveniently used to assess or predict the petrographic composition of clean coal or sinks corresponding to any desired ash level in the cleans. With the help of this diagram, it is also possible to locate the yield level of cleans at which maximum enrichment of vitrinites and exinites occurs with the least amount of mineral-matter content."

Jan 1, 1971

By V. Baboudjian, R. J. Geren, J. Thiriar

"The electrolytic tankhouse at CCR was recognized by management as lagging behind modem refineries in terms of productivity, energy efficiency and controls. The operation was also burdened by high maintenance costs of cells, floors and electrolyte recirculation systems.A bench marking program was started in 1986 to evaluate processes and other technology by visiting major copper refineries in North America, Europe and Japan. The basic principles necessary to optimize the operation were defined, and a program calledCCR 2000 was prepared for approval of the necessary capital investments.This paper describes the results obtained to date and outlines the remaining work to complete the modernization program, in particular, the control of electrolytes, the elimination of the Baltimore groove and studies to modernize the stripping operation or adopt permanent cathode technology.IntroductionThe CCR Refinery of Noranda Copper Smelting and Refining (Noranda Minerals Inc.) , in Montreal East, is one of the world 's largest custom copper and precious metal refineries with a capacity to refine 350000 tonnes of copper per year. The silver refinery, which treats the copper tankhouse anode slime, foreign slime and precious metal ingots, produces 800 000 kg of silver, 26 000 kg of gold and 3800 kg of platinum-palladium concentrate annually. Copper anodes are received from the Horne Smelter at Rouyn-Noranda, Quebec, and Mines Gaspe Division in Murdochville, Quebec. CCR also refines anodes from Hudson Bay Mining and Smelting Co. Ltd. in FIin Flon, Manitoba, and remelts anode scrap along with blister and purchased copper scrap ."

Jan 1, 1993

By C. O. Swanson

THE purpose of this paper is to discuss the use of the dip needle in the field of mining geology. The subject matter is new only to the extent that it reflects the writer' s added experience in recent years. The treatment is brief, and those interested in a more extended analysis are referred to the articles listed at the end of the paper. In the discovery and tracing of mineral deposits, the clip needle, like most other geophysical instruments, can be used in two ways. One method may be termed direct; the other, indirect. The direct method is that of finding or following certain ore-bodies by virtue of their magnetic properties. Explicitly, or by inference, it is the method which many mining men and practising geophysicists have in mind when they consider whether or not a certain property should be studied by geophysical means. In the ideal case, this method demands little or no knowledge of geological conditions. The indirect method uses the clip needle as an aid to purely geological studies in working out the structure of a mineralized area. Although not as simple as the direct method, it enjoys a much wider field of usefulness. The writer's experience in the past fifteen years, which is believed to be typical, is that the indirect method finds application four or five times as often as the direct method. The indirect method is of particular value because it furnishes information concerning the relationship between geological structure and ore occurrence. Most mining engineers will agree that structural control is an important factor in the localization of ore deposits, and therefore that the subject under consideration is of some interest in mining geology. Specifically, then, the present purpose is to outline the principles and practice of using the clip needle in working? out geological structure.

Jan 1, 1941

By G. Cailletaud, I. Guillot, D. Larouche, R. Martinez, D. Massinon

The precipitation of Al2Cu particles in a 319 T7 aluminum alloy has been modeled. A theoretical approach enables the concomitant computation of nucleation, growth and coarsening, based on an implicit scheme using the finite differences. The equation of continuity is discretized in time and space in order to obtain a matricial form. The inversion of a tridiagonal matrix allows us to determine the evolution of the size distribution of Al2Cu particles at t + dt. The fluxes of solute in-between the boundaries, as well as the ones at the boundaries, are computed in order to respect the conservation of the mass of the system. The main results of the model are compared to TEM measurements. Simulations provide quantitative features on the impact of the cooling rate on the size distribution of Al2Cu particles in good agreement with the TEM measurements. This metallurgical model is integrated into FEA software in order to perform mechanical computations. This kind of multiscale approach allows new perspectives to be investigated in the process of designing cylinder heads. It enables a more precise prediction of the microstructure, its evolution as a function of continuous cooling rates and its impact on the integrity of the structure.

Jan 1, 2015

By Sejong Kim, Younghoon Moon, Youngseon Lee, Eunyoo Yoon, Yonghyun Song

"Mg alloy has a high specific strength, however, their thickness reduction was limited on most parts because of their poor stiffness. Since the modulus of rigidity is an intrinsic property, improvement of modulus of rigidity to the enhancement of stiffness is impossible. Therefore, the modification of shape and structure is available method to enhance the stiffness of real part fabricated by Mg alloy sheet. There are many thin walled parts which are located in outer section of electromagnetic system.Poor stiffness is often shown on wide surface area part with steel sheet, which has also high modulus of rigidity. In these cases, various groove patterns are used to increase the stiffness of part. However, some different methods have to be used when general groove pattern can’t be used. So, we would like to propose some new method to high stiffness on thin walled precision forging of Al or Mg alloys.An effect of proposed method on stiffness enhancement can be confirmed by fabrication of prototypes as well as structure and forming analysis based on FEM."

Jan 1, 2015

By L. Bratek, K. Jaworek, M. Czaplicka

Methods for arsenic compound removal from aqueous solutions include processes such as: coagulation, adsorption, membrane techniques, electrochemical and biotechnology techniques. Advanced oxidation using both UV radiation and strong oxidizing agents such as ozone and hydrogen peroxide may also decompose these compounds. It is known that effluents from metallurgical processes contain inorganic arsenic compounds in addition to the organic compounds such as: dimethylarsinic acid and phenylarsonic acid. This paper presents the conditions that lead to the formation of deposits containing mainly arsenic, such as pH, the wavelength of the radiation and the type of oxidant, for this type of effluent.

Jan 1, 2014

By M. Tsesarsky, M. Hazan, E. Gal

"Rock masses comprised of stiff inclusions in softer matrix are common in various geological environments. The heterogeneity and multi-scale nature of these materials make the evaluation of their mechanical properties a challenging task, which cannot be accomplished using conventional laboratory tests and composite mixture rules. We employ the homogenization method to estimate the mechanical properties of geological materials with inclusions. The homogenization method solves the equations of elasticity on the material (microscopic) scale for a unit cell subjected to unit strains under periodic boundary condition. The micro-scale elasticity equations are solved using the Finite Elements Method, and are in turn used to obtain the structure scale (macroscopic) material matrix.In this research, Finite Element models for unit cells with spherical and ellipsoidal inclusions were developed. Using the unit cells, a parametric study of the geometrical and statistical microscopic properties of the material composites was performed. The following parameters were studied: volumetric ratio, Young’s modulus ratio, size-distribution of inclusion and inclination angle of inclusions. The main purpose of the parametric study was to study the deviation from isotropy as a function of the aforementioned parameters.It was found that for volumetric ratio of 5%-40%, the deviation from isotropy increases, as the volumetric ratio of inclusions increases. For spherical inclusions, most of the cases studied exhibit quasiisotropic behaviour; whereas ellipsoidal inclusions exhibit considerable deviation from isotropy. The inclination of the ellipsoidal inclusions enlarges the deviation from isotropy (9% at random orientation and 26% at 0°)."

Jan 1, 2015

By G. Wren

As base metal sulphide resources become increasingly challenging to process, producers seek alternative options to treat concentrates. This study considers the mineral, elemental, and leaching character of a West Australian nickel sulphide deposit (Cosmos Nickel Project). After a brief review of the published work bench top leach tests were conducted to examine the factors which impact the kinetics of nickel sulphide leaching such as particle size, temperature, acid strength and type, concentration of copper sulphate and sodium chloride, and oxygen partial pressure. The effect of sodium chloride was considered due to the common occurrence of hyper saline water at West Australian nickel sulphide mine sites. Ultrafine grinding to an 80% passing size of 10 µm resulted in high nickel leaching efficiency. Moreover, higher concentrations of acid, copper(II) and sodium chloride also gave higher nickel and cobalt leaching efficiencies but arsenic precipitated as FeAsO4. Under the most suitable conditions the extractions of nickel, cobalt and arsenic at 90oC after 6 hours were >95%, 90% and <5%, respectively. The comparison with results from high pressure operations indicates the possibility of using a hydrometallurgical flowsheet based on fine grinding and atmospheric pressure leaching and warrants further investigations.

Jan 1, 2014

By Arthur. H. Winckers, Stephan L. Chryssoulis

"The deportment of gold in residue samples of cyanide leach tests of David Bell ore from level 6A block 13 was established using a comprehensive quantitative mineralogical approach. In every test the feed was first pre-aerated for 4 hours, followed by 48h cyanidation. Test no. 2 was done without lead nitrate and yielded a residue assaying 3.03g Au/t. In test nos. 4 and 9 lead nitrate was added before pre-aeration at 0.03kg/t and 0.3kg/t respectively yielding residues of 1.04 and 0.81 g Au/t.The mineralogical approach employed to establish the deportment of gold involved superpanning, to preconcentrate the free gold and assaying of the tailing fraction to determine the gold associated with quartz. It was thus determined that without lead nitrate added 47.2% of the lost gold is in the form of residual free gold particles less than 20 µm in size. It is this form of gold which is under represented in the residues of leach tests with lead nitrate added.Having eliminated coarseness of gold particles as a factor for lower recovery, it was determined that the residual gold particles have extensively contaminated surfaces. Amongst the deleterious surface contaminants identified: S, As, Ag, Sb and Hg, the two most harmful are S and Hg because of their concentration on the surface and rate of accumulation.Mercury and Ag are minor constituents of native gold at David Bell (average composition Au: 78.9 wt%, Hg: 18.5 wt% and Ag: 2.6 wt%) and they become enriched on the surface of residual gold particles because of their slower rate of dissolution in cyanide. The other elements absorb onto the gold particles from solution.The beneficial effect of lead nitrate was documented by comparative surface analysis of gold from residue samples of 48 hour leach testing with and without lead nitrate added and from time dependent (0-2 hour) leach tests in the presence and absence of lead nitrate. Lead nitrate accelerates the dissolution of gold by performing the following functions: (i) catalytic effect on the cyanidation of gold by accepting electrons; (ii) reaction with surface sulphur to form PbS which is then removed by oxidation; (iii) catalytic reaction on amalgam and Ag facilitating the cyanidation of Hg and Ag thus slowing down their build up onto the dissolving gold particles and (iv) the precipitation of sulphide sulphur from solution thus minimizing its build up on the surface of dissolving gold particles which is believed to facilitate the access of cyanide ions."

Jan 1, 1996

By Hevina S. Dashwood

This paper proposes to build on my previous research (Dashwood 2012), which analyzed how and why the norm of sustainable development became institutionalized in the global collaborative corporate social responsibility (CSR) initiatives of major mining companies. Since the late 1990s, the majority of major global mining companies have employed the norm of sustainable development to frame their individual CSR policies and to inform industry collaboration at the global level through the International Council on Mining and Metals (ICMM). This paper proposal seeks to address lingering questions from that research, by developing an explanation for how the normative frame of sustainable development has translated into specific CSR standards adopted by the mining industry. Preliminary findings suggest that, although the global mining industry has reached broad consensus on the meaning of sustainable development in the context of mining, there remains considerable variation between mining companies in terms of which specific global standards they adopt. As members of the ICMM, major mining companies are required to report according to the Global Reporting Initiative (GRI) indicators relevant to mining, and there has been wide-spread up-take of the ISO 14,001 environmental management system standard. However, other global standards, such as the International Finance Corporation (IFC) Performance Standards and the Extractive Industry Transparency Initiative, have not been uniformly adopted by the mining industry. What explains this variation? The paper employs a three-level institutional framework (rational choice institutionalism, historical institutionalism and the ?new? institutionalism in organization theory) to explain the influences on the adoption of CSR standards in the global mining sector. Existing research confirms that institutional context is an important factor in explaining CSR adoption in the mining sector (Dashwood 2012). Are similar forces at work in explaining the variation in adoption of specific CSR standards? A three-level institutional analysis lends itself to uncovering influences both external to mining companies (such as pressures from stakeholders), as well as internal company dynamics (such as managerial discretion). Furthermore, the framework can incorporate dynamics operating at the global level (such as isomorphism), the national level (such as the regulatory regime) and the local level (such as community needs and environmental challenges). The theoretical significance of this framework is that the influences on CSR adoption are more complex than can be explained in a single approach (such as narrow rational choice/cost benefit explanations). On a practical level, insights into how global standards get interpreted and acted upon by individual companies could lead to the development of more appropriate and effective global standards.

Aug 1, 2013

By Robin N. Adair

Abstract -The Halfmile Lake stratiform volcanogenic massive-sulfide deposit consists of pyrrhotite­ rich breccia-matrix sulfides and pyrite-pyrrhotite-rich layered sulfides that form a laterally continuous sheet stratigraphically underlain by an extensive pyrrhotite-chalcopyrite-quartz stringer zone. Mineralization is hosted by a sequence of felsic pyroclastics and volcanic-derived, fine-grained metasediments. The proportion of volcanic to sedimentary rocks indicates increasing vent proximity from southwest to northeast across the deposit area. Fine- to medium-grained felsic pyroclastics and roughly equal amounts of fine-grained metasediments comprise the stratigraphic footwall to the mineralization. Quartz-feldspar porphyritic bodies cut this sequence and may have provided the heat source for exhalite activity. Felsic tuffs, locally crystal-rich, and lesser amounts of metasedimentary rocks make up the immediate stratigraphie hanging wall. This sequence is stratigraphically overlain and locally interfmgered with matie volcanics that contain substantial proportions of felsic fragments. Deposition of sulfides post-dated the beginning of felsic volcanism, which places the deposit in the middle of the Lower Tetagouche Group. Compositions of the volcanic rocks range from basait to rhyolite and exhibit sub-alkaline affinities. Strongly overprinted whole-rock, trace-element, and REE geochemical signatures resulting from mineralizing hydrothermal activity confirm the genetic relationship be­tween the stringer zone and the mineralized sheet. Large-scale D1 folding has overturned the entire sequence. D1 thrust faults and related sheath-like folds have profoundly affected sulfide distribution. D2 is manifested by a penetrative S2 foliation, and D3 is represented by large-scale open folds.

Jan 1, 1992

By T. A. Utigard, S. Pedler

Ilmenite from the Everett deposit in Quebec was characterized both chemically and mineralogically. The sample investigated contained the following main components: 40% Fe2O3, 21% TiO2 and 21% SiO2. The ilmenite grains contained about 20 to 25% hematite intergrown blades, with widths ranging from 2 to 30 \u03bcm. Crushing the sample to less than 0.85 mm led to significant liberation of the ilmenite from the gangue minerals. Gravity separation followed by magnetic separation of this size fraction led to a TiO2 concentrate grading of about 30% TiO2, with a recovery of 94%.

Jan 1, 2010

By Jr. Jones

This paper is derived from a document that compiles autogenous and semi-autogenous mill installations worldwide, through the end of 2010. Updates have been solicited from all major mill manufacturers and most have responded. A review of AG/SAG mills sold to date and in the last five years indicates that the AG/SAG mill market is very healthy and the trend is larger diameter mills with high diameter-to-length ratios. Ring motors (gearless) are the preferred drives for large mills even though the power transmitted through a gear drive is expected to near 11,000 kW per pinion in the near future.

Jan 1, 2012

By E. Busse

"Heath Steele Mines Ltd. operates a lead-zinc-copper mining and milling complex in New Brunswick.• During the past seven years, as ore reserves increased, the mill capacity was first expanded to 1,600 tpd and then to 3,000 tpd. In the last expansion, instead of building a completely new 3,000-tpd mill, or adding to existing installations, Heath Steele retained service facilities, buildings, ore bins, Jab, etc., and removed and replaced almost all existing process facilities. Requiring a complete mill shutdown, the expansion had to be carried out in minimum time. Also, new equipment had to fit into existing space. Critical path networks of the project were prepared, a tight schedule for construction was mapped out and progress charted daily to detect problems before they could interrupt the schedule. Heath Steele supervised the purchasing, handling and storage of new equipment, maintained liaison with the engineering contractor and became a sub-contractor, using its own staff to install all flotation equipment and process piping. The 1,600-tpd installation was dismantled and a 3,000- tpd unit was successfully put onstream in 5 months - on time and within budget. One benefit stemming from the expansion: production increased 87 per cent while operating and maintenance labour rose only 8 per cent."

Jan 1, 1972

By C. Jay Hodgson, P. J. MacGeehan

"The gold ore zones of the Campbell and Dickenson mines occur within a km-wide, 2 km-long zone of highly altered and anomalously fissile and deformed volcanic and subvolcanic intrusive rocks, cut by a series of mainly post-deformation mafic and quartz-feldspar porphyry felsic dykes.Three main periods of gold ore-forming hydrothermal activity are recognized. In the first, the mine rocks were extensively altered and gold and arsenic enriched; syn-volcanic auriferous veinlet and low-grade chemical sedimentary ores were deposited in what was a major discharge zone of a submarine hydrothermal system. The chemical sedimentary ores are closely associated spatially and temporally with domal rhyolitic extrusions. Because of its mechanical and chemical properties, this synvolcanic alteration zone became the locus of later deformation, and the site of the generation of auriferous hydrothermal solutions, perhaps by pressure solution processes at depth. These solutions deposited, synchronously with deformation and metamorphism, the second and most economically important type of ore zones in the mine: large foliation-parallel and foliation-oblique banded carbonate- 'chert' Rssure-filling veins.In the third and final mineralizing event, high-grade, pipeshaped zones of siliceous replacement-type mineralization, and quartz-arsenopyrite-gold veins, were superimposed on the previous mineralization types after most of the deformation, but before the emplacement of the late dykes. The source of heat and also possibly the fluids for the third mineralizing period may have been the dyke-forming igneous activity. The textures and mineralogy of the banded carbonate- 'chert' veins suggest a near-surface (<3 km) environment of deposition, but their relationship to the fabric of their host rocks indicates they were emplaced in an environment, presumably at considerable depth (5-10 km?), in which the rocks were undergoing intense penetrative deformation. This anomaly is unresolved."

Jan 1, 1982

By Claudio Acuña, Sergio Romo, Gerardo Fuentes

The leaching kinetics of a zinc concentrate in autoclave reactors were studied. A sample of concentrate from Bolivia, with typical mineralogical characteristics of the Andes region, was used. A concentrate containing 49% zinc and 145 ppm of silver from Minera Viacha was characterized chemically and mineralogically (atomic absorption, X-ray diffraction, and SEM microscopy) and tested in bench scale reactors. Two types of autoclave batch reactors were used at 40 bars of oxygen pressure and three levels of temperature (150°C, 200°C and 250°C). The solid to solution leaching ratio was 1:10 (10% sulphuric acid concentration). The effect of the particle size of the concentrate on the leaching kinetics was studied (P80: 145 and 45 µm). Iron from the leaching solution was removed by precipitation by increasing the pH in order to generate a clean solution for zinc electrowinning. The zinc solution was used to evaluate the feasibility of cathode production at the laboratory scale. Zinc extractions with higher liberation (P80 = 45 µm) reached up to 98%. Ground concentrate with finer sizes resulted in agglomeration and the use of dispersing agents did not improve slurry mixing. The leaching solution contained 55 g/L zinc and 7 g/L iron; it was purified by precipitating iron. The precipitation was evaluated using sodium hydroxide and ammonium hydroxide. In the first case, a colloidal suspension of ferric salts was formed while in the second case, different iron compounds were precipitated. The precipitate obtained with ammonium hydroxide had better filtering properties. Electrowinning was carried out using two types of cathodes (stainless steel and aluminium) and solutions purified with ammonium hydroxide. Zinc cathodes formed on stainless steel presented a better physical quality than those formed on aluminium.

Jan 1, 2015

By R. C. A. Thurston

"The lack of notch ductility in structural steel in general, and in ship plate in particular, has been the object of widespread attention in the metallurgical world since the spectacular collapse of the ill-fated S.S. Schenectady in 1943. Numerous investigations have been carried out, many new tests have been developed, and a vast amount of useful data has been published, with the result that our knowledge is now far more advanced than it was at the time of this disaster. Interest has focused largely on the medium strength steels, and the various factors which cause a normally ductile steel to behave in a brittle manner in the presence of a notch and at relatively .low temperatures have been thoroughly studied.The literature available on high-tensile steels, however, is less extensive and the present paper is intended to supplement this information. Notch toughness tests have been carried out, at the request of the R.C.N., on a high-tensile manganese steel in the form of commercial ship plate. One of the newer tests, the tear test, and the Charpy V-notch impact test, were used to examine the characteristics of plate for the construction of an ice-breaker. About 250 plates, mainly in the thickness range from 11,4 in. to 1 % in., were tested. An an-alysis of the results obtained is presented, certain aspects of the tear test are discussed, and the correlation between the two types of test is studied. On the basis of information available from casualty ships, the plates, with few exceptions, were considered to be satisfactory."

Jan 1, 1959

By R. Rumpold, J. Antrekowitsch

"The continued increase of the automobile production leads to a higher platinum, palladium and rhodium (PGM) demand. Due to the high value of the PGMs the recycle of these metals from automotive catalysts is of special interest. Pyrometallurgical processes, which are only focused on the PGMs, represent the state of the art of automotive catalysts recovery. However, hydrometallurgical recycling processes offer additional recovery of other valuable metals and compounds. The method presented in this paper is based on a combination of hydrochloric acid and hydrogen peroxide to dissolve the valuable metal fraction which can be precipitated afterwards.INTRODUCTIONPlatinum and the corresponding metals from the PGM group, especially palladium and rhodium are well known as catalytic active materials. They support chemical reactions which are inhibited. This effect is used to decrease the amount of harmful compounds like hydrocarbons, carbon monoxide or nitrogen oxides in automotive exhaust gases. The generation of these toxic substances is based on incomplete combustion, which in turn is caused by non-ideal conditions in the combustion chamber. Catalytic converters minimize the harmful compounds by supporting the following Reactions 1 – 3 (Votsmeier et al., 2009).CO + ½ O2 ? CO2 (1)CnHm + (n + ¼ m) O2 ? n CO2 + ½ m H2O (2)2 NO + 2 CO ? N2 + 2 CO2 (3)Platinum and palladium are very effective for the oxidation (Reactions 1 and 2), while rhodium supports the decomposition of nitrogen oxides by carbon monoxide (Votsmeier et al., 2009). The classical three way catalyst was a platinum – rhodium combination with a Pt:Rh ratio of 5:1 (Hagelüken et al., 2005). Today the platinum, palladium and rhodium ratio is highly variable and strongly depends on the engine type as well as on the car producer. Diesel engines are operated with a super stoichiometric air addition in comparison to spark ignition systems. Therefore the exhaust gas composition and off gas temperature is different. Based on the high oxygen amount, diesel engines produce less carbon monoxide and hydrocarbons but more nitrogen oxide in contrast to gasoline engines. This leads to various requirements for the catalytic converters."

Jan 1, 2012