Search Documents

By Kevin P. Plucknett, Z. Memarrashidi

"In the current work, factors influencing the corrosion mechanisms of TiC and Ti(C,N) based cermets are reviewed. Cermets were typically prepared with 30 vol.% of metal binder, in the form of various in-situ reaction-formed Ni3Al alloys. Commercial WC-Co hardmetals were also examined as baseline materials. The assessment of corrosion involved a variety of electrochemical measurements, including open circuit potential and potentiodynamic polarisation. The corrosion potential and current density were determined, following Tafel extrapolation, allowing estimation of the corrosion rates. Post-corrosion characterisation involved scanning electron microscopy analysis and associated energy dispersive X-ray spectroscopy of the sample surfaces. It is demonstrated that the primary corrosion mechanism for this type of cermet is dissolution of the metallic phase during oxidation attack, and thus this response can be expected to increase with the amount of binder in the cermet, although degradation can be subtly affected by composition (i.e. alloy composition, C:N ratio, impurities in the ceramic phase, etc.) and test procedure (i.e. aerated vs. de-aerated electrolytes). It was observed that addition of N content into the ceramic phase is beneficial to the corrosion characteristics of TiC based cermets, through significant refinement in the grain size of the hard phase. Similarly, elimination of impurities, such as W in selected TiC powders, also improves the corrosion resistance.INTRODUCTION Cermets are prepared using the combination of a hard, high elastic modulus ceramic phase with a ductile, high toughness metallic binder. This pairing of hard and ductile components ensures wide application of cermets in demanding wear environments. These materials are consequently used industrially in both bulk and coating form. The most common example of such a composite system is based on the use of tungsten carbide with a cobalt-based binder (WC-Co), which has been widely examined over the past 80 years. However, while WC-Co has been shown to exhibit an excellent combination of high strength and wear resistance, the corrosion and high temperature properties of this material are relatively poor. In addition, WC-Co possesses a high density (~13–14 g/cm3), which makes it a less desirable option when the component mass is a design factor (i.e. use in aerospace). In particular, the aqueous corrosion response of WC-Co limits its use in wear environments where combined corrosive degradation may occur (i.e. tribo-corrosion scenarios). Alternate cermet systems are therefore being actively developed due to these performance limitations."

Jan 1, 2017

By L. Gonzalez-Sardi, W. McCombe, M. Pearson

Pressure oxidation is increasingly being used for processing refractory sulphide ores and concentrates because it offers highly effective base metal and precious metal extraction while minimizing elemental sulphur, arsenic & mercury emissions. Yet pressure oxidation processes introduce new safety concerns and process risks as demonstrated by a number of safety incidents over the last 20 years, including overfilling, oxygen-metal fires, nozzle/sparger failures, and uncontrolled pressure relief events. Chemical Process Safety regulations in the United States and Canada mandate that companies constructing or operating chemical process facilities perform a rigorous hazard and risk analysis based on either ANSI/ISA-84.00.01 or IEC 61511 safety standards to determine the level of protection required for each hazard in the plant. This paper describes the application and implementation of three (3) unique safety instrumented systems developed by Hatch for ensuring the safe operation of three different pressure oxidation processes.

Jan 1, 2014

By B. S. A. Tatone

The surface roughness of unfilled rock discontinuities has a major influence on the deformational and hydraulic behaviour of discontinuous rock masses. Although it is widely recognized that surface roughness is comprised of a large-scale (waviness) and small-scale (unevenness) components, most investigations of surface roughness have been restricted to small fracture surfaces (< 1m2). Hence, the influences of the large-scale components of roughness are often neglected. Furthermore, these investigations typically focus on analyzing roughness in terms of two-dimensional profiles rather than the complete three-dimensional geometry, which can lead to potentially biased estimates of roughness. This contribution demonstrates the use of a new optical digital measurement system, based on the principle of triangulation, to digitize a large-scale natural rock discontinuity surface at both outcrop-scale (~6m x 2m) and lab-scale (~100mm x 100mm). Subsequently, the digitized surfaces are systematically analyzed using the three-dimensional roughness methodology proposed by Grasselli to investigate the dependency of roughness on sample window size and measurement resolution.

May 1, 2009

By J. E. Carrasco, J. D. Stinnette, R. A. Alvarez

"Chuquicamata Underground Mine is one of the main projects for the Chilean government copper company (CODELCO). Underground mine project has been under construction since 2013 and presents a solution for the lower production levels of the open pit and prolongs the life of the mine for the next 40 years. Currently, around 2000 workers operate in the mine daily. Dozens of trucks and heavy machines drives through all main routes and access in the mine. As a mine under construction not all the infrastructure necessary to operate safely in the mine has been completed. Risk of a truck or fixed facility fire is always a challenge to keep under control. One important part of fire simulation relays on what we can do prevent a fire and what can be done with the existing infrastructure to control a declared fire and start evacuation plans. This study has been made as a feasible emergency plan to implement, in this case, of a mine under construction, were limited resources are available. Several fire scenarios have been made to support all the emergency plan strategy and a detailed step by step procedure indicates what the elements of a fire emergency plan and risk analysis are.INTRODUCTIONThe main objective of this study is to describe the importance of fire risk analyses (FRAs) and different methods to be used before commencing fire simulation and methodology steps utilized for a fire emergency plan strategy (EPS) at the Chuquicamata underground mine. It also describes how to classify zones which are going to be affected by fumes and gases propagation derived from the exact location of a fire event. Fire simulation study is helpful to determine the impact on a ventilation system with the main purpose of providing relevant information to complement emergency plans and stablished control techniques in ventilation design and its operation. Most fire simulation studies only concentrates in simulation techniques on itself. But what is the next following step in developing an emergency plan? How can we evaluate, classify and treat risky areas? This study is focused mainly in the phases before and after a fire simulation process. Phases corresponds to a good FRA and how output data can be used for an EPS."

Jan 1, 2019

By G. E. Norman, J. F. Jackson, A. L. Mckague

"The treatment of nickel-copper concentrate in the new smelter at Falconbridge Nickel Mines Limited, Falconbridge, Ontario, is described. The concentrate in a slurry form is partially roasted in a fluid-bed roaster and the calcine is smelted in an electric furnace. The roaster gases are treated in an acid plant. IntroductionSmelting began at Falconbridge in 1930 with the first blast furnace treating high-grade ore containing 2-3% nickel. In 1933, the Falconbridge concentrator was built and started producing a bulk sulphide concentrate containing 4% nickel. A sinter plant was built to agglomerate and partially roast this concentrate. The sinter was smelted in blast furnaces along with high. grade magnetic ore. Matte from the furnaces was treated in Pierce-Smith converters to produce shipping matte which was refined at the company&apos;s plant in Norway."

Jan 1, 1980

By Knud Sinding

Environmental reporting by mining firms takes many forms and change frequently. The objective of these reports is related to increasing the legitimacy of mining firms with their diverse stakeholders. This study, focusing on internet-based reports, shows that there are considerable variations in reporting. This phenomenon is interesting because it belies the efforts pursued by leading industry members under iniatives such as the Global Mining Initiative and the Mining, Minerals and Sustainable Development project. The observed variation, both internally among reports and between reports and other industry policy statements, suggests that the industry needs to explore the possibilities for more convergence in terms of reporting quality. Based on theoretical constructs from the management literature we present a series of arguments defining necessary and sufficient conditions for durable and well-institutionalized reporting practices and standards.

May 1, 2002

By A. Vervoort, A. Govaerts

Geostatistical concepts are often difficult for students to understand, even those with a strong mathematical background. One of the main problems is the link between the variation of the parameter value in space or time and the calculated experimental semivariogram. Another challenge is differentiating between directional and omnidirectional semivariograms and their interpretation. For these reasons, interactive tools were developed based on the free public domain software R. The use of these interactive tools is limited to educational situations only (i.e., to visualize basic concepts). The interactive modules can be accessed at www.bwk.kuleuven.be/geostatistics.

Jan 1, 2014

By George K. Foster

The Jeffrey mine of the Canadian Johns-Manville Co., Limited, is in the town of Asbestos, situated approximately 100 miles northeast of Montreal and about the same distance southwest of Quebec, in Richmond county, Quebec. Mining operations were started in 1881 on outcrops on a hill, as a side-hill cut, followed by a second and third cut. This development was the forerunner of the present large open-pit operations, the mine now ranking as the largest open-pit asbestos mine in the world. Operations were first carried on by hand, then by horsepower and later by stem cableways. By 1914, the derrick spans, 2,000 feet or more long, became unwieldy. To overcome this, and also to eliminate hand labour as much as possible, steam shovels and railway haulage were introduced. The steam shovels were replaced in 1928 by larger electric shovels of the full-revolving type.

Jan 1, 1946

This paper describes results of an investigation of fracture during tube expansion of 5052 and 5754 aluminum seam-welded tubes to optimize the forming of aluminum tubes during hydroforming. The tubes were produced in laboratory by press forming of tubular blanks and pilot-scale high frequency induction welding. The effect of property mismatch between the weld and base metal has been investigated. The material work-hardening was obtained by roll forming of sheet blanks in the 0-temper and H32 temper condition. The results showed that a significant work-hardening can be present in aluminum tube without causing weld fracture during tube expansion. The work-hardening increases the yield-strength mismatch between base metal and weld. Annealing reduces the hardness of base metal leading to more uniform deformation during tube expansion. As a result the occurrence of weld fracture is reduced. The study showed significant deformation of the welds during tube expansion. Weld thinning can be as large as parent-material thinning before fracture. To avoid fracture at the weld joint, good formability and high yield strength of the weld is needed. FEM simulation showed that minimizing the width of the weld joint can reduce thinning of the weld.

Jan 1, 2004

By H. Hao

This paper outlines the development of a 2-D axisymmetric mathematical model to predict the evolution of temperature during the Direct Chill (DC) casting of AZ31 magnesium billets. Model predictions of temperature have been compared to measurements made on an industrial DC casting machine at Timminco Ltd, in Haley, Ontario. These measurements have been used to fine-tune the thermal boundary conditions employed in the mathematical model, The model, which is based on the commercial finite-element code ABAQUS, has been developed as part of a strategic project aimed at improving the DC casting process for light metals through a reduction in casting related defects and increased productivity.

Jan 1, 2004

By Daniel Hodouin, Claude Bazin

"This paper examines the economic advantages of adapting the production grade and recovery targets of a flotation circuit as a function of metal prices. The study is periormed using a steady state simulator for a Cu-Zn differential flotation circuit operating under the following strategies of 1) Maintaining constant operating targets, 2) Maximizing individual circuit Net Smelter Return and 3) Maximizing the global Cu-Zn circuit efficiency. Results are compared to assess whether or not one of the strategies produces benefits significantly higher than the others. A discussion of the tools required to achieve such a kind of control completes the paper.Paper not Available at Time of Publication"

Jan 1, 1997

By R W. Drybrough

The program to increase production at Sherritt Gordon&apos;s Lynn Lake property, which began in 1956, included increasing the rope speed and the horsepower of the ore hoist at the "A" shaft. Because of the limited power sup-ply from the two 7,000-hp. hydroelectric plants, and the ? 3,600 hp. predicted for the combined hoisting requirements of the three production shafts, it was considered desirable to lessen the impact of this type of load on the relatively small power system by equipping all future hoisting arrangements with Ward Leonard direct-current drives. The manually operated 8-by 4-ft. hoist at the "A" shaft had a rope speed of 1000 f.p.m., and was driven by a 385-hp., 380-r.p.m. wound rotor motor with liquid rheostat control. This A.C. drive was replaced by a semi-automatic Ward Leonard direct-current drive with a 515-hp., 566-r.p.m., shunt wound motor, providing a rope speed of 1,500 f.p.m. During several months preceding the con-version, all possible preparations were carried out to keep the changeover period to a minimum, and this resulted in a total shutdown time of twelve days. The capability of the "A" Shaft hoist was increased from 109 tons per hour to 134 tons per hour, and both mechanical and electrical maintenance were reduced considerably. The total cost of the conversion amounted to $130,000. The hoistmen who had been required for the manual A.C. drive were transferred to the new Farley shaft, and the reduction in operating labour costs of the "A" Shaft hoist

Jan 1, 1965

By K. J. Daun, C. J. Shi

UsiborThrough the second step heating at 900 °C, the spectral emissivity shows a gradually decreasing trend with increasing soak time, caused by the surface phase transformation from Al® 1500P coupons are austenitized in a Gleeble 3500 thermomechanical simulator using a two-step heating procedure in an argon atmosphere. Variations in spectral emissivity are measured in-situ using a near infrared spectrometer and ex-situ with a Fourier transform infrared reflectometer. Microstructural evolution and surface roughness are investigated using optical microscopy, FE-scanning electron microscopy, and a surface profilometer. A series of phase transformations of Al-Fe-Si intermetallic phases at the coating/steel substrate interface cause the surface phase and surface roughness to change, which in turn influences the spectral emissivity. At the beginning of the first heating step, the coupons have very low spectral emissivity, due to the molten Al-Si coating. Spectral emissivity increases significantly with increasing soak time from 5 to 12 minutes, associated with the surface phase transformation of the coating into Al7Fe2Si intermetallic phase and an increase in surface roughness. 5Fe2 into AlFe intermetallic phase with a decrease in surface roughness.

Jan 1, 2015

By H. R. Huffman

"This paper reviews the history of iron powder production, and outlines the varions production methods. The uses of iron powder and the reasons for its use are also covered. The paper concludes with a look at future trends in powder metallurgy.INTRODUCTION TO POWDERSTHE IRON POWDER INDUSTRY is enjoying a very rapid growth. The annual consumption of iron powder is now at the 100,000-ton level, twenty times higher than it was at the end of World War II, and the yearly in-crease bas been almost consistent at 20 per cent. This is expected to increase, bringing the tonnage to 200,-000, or even (according to some experts) to 270,000, in 1970. In any event, powder metallurgy is expanding at high speed and making an important impact on the production of iron and steel products. Some indication of the faith in the future market may be indicated by the commencement of three new powder production plants in Canada with a total capacity of 136,000 tons annually."

Jan 1, 1969

By O. Lashkari

Manipulation of pouring temperature is an efficient way to produce different microstructural features. In order to characterize the microstructure of rheocast billets due to different superheats of 615-695 °C, the parallel plate compression method was employed. Foundry 356 Al-Si alloy with different morphologies of primary a-Al particles were tested at different initial pressures of 4,8, 11,2 KPa, The resulted strain-time graphs were further treated mathematically to calculate viscosity of SSM billets. The interrelationships of viscosity, the microstructure and primary phase flow during compression are discussed, It is shown that the dendritic primary a-Al structure has the highest viscosity number which is almost three orders of magnitude greater than those for globular morphology, The current research have, for the first time, shown the validity and reliability of "parallel plate compression viscometry" method in characterizing microstructural evolution of Rheocast SSM billets.

Jan 1, 2005

By H. Blaha, H. Wagner

"Room and pillar workings in salt mines are preferred sites for underground waste disposal. A critical issue in selecting waste disposal sites is long-term behaviour of such workings. The long-term behaviour of salt pillars is controlled by the pillar geometry, i.e. the height, width and length of pillars and the level of pillar stress. The latter has a strong influence on creep characteristics of salt pillars whereas the width to height ratio of salt pillars determines the strength of pillars and the deformation characteristics of salt pillars.Three different regimes of pillar creep behaviour of salt pillars can be distinguished, namely a stress level below which the rate of creep approaches a value of zero, a stress range where the rate of creep is constant and finally a stress level above which the rate of creep accelerates. Long-term stability of room and pillar workings can be assured only when the pillar stress level falls within the first stress regime. Strength and creep tests on model salt pillars have shown that at stress levels below 40% of pillar strength the rate of creep approaches a value of zero, between stress levels of 40% and 65% the rate of creep is constant but increases with stress level. Above pillar stress levels of 65% the rate of creep accelerates.Long-term measurements of pillar deformation and surface subsidence above relatively shallow room and pillar workings in salt mines have confirmed these observations. Long-term strength of salt was found that be between 60% and 65% of short term strength. The evaluation of salt pillar behaviour on the basis of critical pillar stress levels was found to be superior to the traditional factor of safety concept because it allows relating pillar deformation measurements to actual pillar conditions. The approach described in the paper was used successfully to evaluate the stability of room and pillar workings in a salt mine and to design strategies to stabilise critical pillar workings."

Jan 1, 2015

By Kevin Bell

About Beltek Inc. For more than a decade Beltek, Inc. has been working with national and international organizations to harness and deliver solutions which gain real ebusiness advantages in today&apos;s world. Our objectives are to partner with our customers to achieve maximum results, while reducing costs. At Beltek, we provide a commitment to you and your organization&apos;s needs. Whether that be delivered by ensuring our services and products are state of the art or by providing a level of personalized service, which makes you feel like the center of attention, Beltek is about adding value to every job we work on. The individuals who work at Beltek quickly become your friends because we share your passion and enthusiasm for the business we are in. That&apos;s why every person is a leader in his or her respective fields. Having these individuals as apart of our business ensures you get the best out of our equipment, receive the very latest in advise, problem solving and support. We also pride ourselves on our ability to remain flexible at all times because we know deadlines and schedules can change quickly, so we always go the extra mile to deliver exactly what you need.

May 1, 2004

By G. E. Agar, W. B. Kipkie, R. A. Tenbergen

"This paper describes the successful pilot plant testing of a flowsheet, developed at Inca Ltd.&apos;s J. Roy Gordon Research Laboratory (JRGRL), for improved separation of the constituent minerals in a bulk copper-nickel concentrate.The flowsheet utilized the fact that xanthate concentration on the mineral surfaces is the most important variable affecting the high lime separation and that reduction of the xanthate concentration could be affected by an oxidative conditioning stage.When the adsorbed xanthate was reduced to a suitably low level, chalcopyrite and pyrrhotite could be floated to leave a high-grade nickel concentrate as the residue. Sodium cyanide was added to the froth product 10 depress pyrrhotite and any remaining pentlandite. The temporary depression of chalcopyrite by the sodium cyanide was overcome by introducing a conditioning step following cyanide addition . The advantages of the flowsheet; improved copper-nickel separation, operation without heating of the pulp, production of both high-grade nickel concentrate (29.5% Ni, .26% Cu) and copper concentrate (<0.5% Ni, 30% Cu) were all realized.IntroductionLaboratory test work undertaken at Inco and described previously(1) has demonstrated the importance of low xanthate concentrations on the mineral surfaces in the copper-nickel separation at the Copper Cliff mill.It was determined that oxidation of the separator feed (a cleaned bulk concentrate, grading about 11% Cu and 11% Ni) to lower the xanthate concentration on the mineral surfaces prior to separation significantly improved the quality of the separation (CI 4)*, particularly when no cyanide is used, but also when cyanide is added. As well, it was found that the oxidation permitted a pentlandite-pyrrhotite separation - the oxidation step brought about a decrease in the flotation-rate of pentlandite leaving pyrrhotite and chalcopyrite largely unaffected. Consequently, it was possible to produce a highgrade pentlandite product (30% Ni, 0.3% Cu) at ~83% Ni recovery , as well as a high-grade copper concentrate (0.5% Ni, 30% Cu at -96% Cu recovery)."

Jan 1, 1985

By S. Hume, J. Shepherd

Meso-2,3-dimercaptosuccinic acid(DMSA) was studied as an additive for thiosulfate leaching of gold. DMSA was added to solutionscomposed of either sodium thiosulfate or calcium thiosulfate and the solutions were tested for their ability to leach pure gold samples as well as a calcined gold ore from Barrick Gold Corp. Results showed prolonged leaching of pure gold samples when DMSA was added at a concentration of 5µM; however, higher concentrations were shown to inhibit leaching. Differential capacitance measurements of the interface indicated that DMSA adsorbed as a defective monolayer on the surface of gold at low concentrations and formed a more compact monolayer with increased concentration. It is proposed that a concentration of 5µM DMSA produces a defectivemonolayer on the surface that still allowsthe transport of oxidants to the underling metal while inhibiting the formation of polysulfide passive layers that arise fromdecomposed thiosulfate.The 5µM DMSA/CaS2O3 system was also studied using calcined ore. Results showed that the initial leaching rates in the presence of DMSA are lower than those obtained in thiosulfate alone. However, after 10h, prolonged leaching is again observed when DMSA is included.

Jan 1, 2015

By Robert B. Parsons

"Finance Minister Paul Martin&apos;s second budget might be good for Canada&apos;s mining industry in the long run, but the budget raises a number of concerns for the industry in the near term. The budget papers suggest that the 25% resource allowance is not working as intended, and report that the Department of Finance will be reviewing this valuable allowance. The so-called ""large corporations tax"" rate will be increased. This annual tax, which is imposed on a corporation&apos;s capital even when the corporation is not in production, is particularly harmful to the mining sector.IntroductionThe Honourable Paul Martin, in his second federal budget, emphasized spending cuts and made only modest tax changes. However, two of these tax changes could have a serious impact on the Canadian mining industry: the proposed review of the 25% resource allowance; and, the increase in the large corporations tax rate.Personal Tax Measures Personal Tax Rates UnchangedThe government has been under political pressure not to increase personal tax rates. Mr. Martin&apos;s announcement that rates would not change will be popular."

Jan 1, 1995