Search Documents

By A. J. Monhemius

This paper reviews the history of modern iron-control processes in hydrometallurgy. Attention is paid to processes developed in the electrolytic zinc industry for removal of iron from zinc sulfate leach liquors and the problems faced by the industry in the safe disposal of the iron residues produced by these processes. Past lessons learned are projected onto current efforts to develop hydrometallurgical processes for treatment of copper sulfide concentrates. It is argued that any attempt to create a \u201chydrometallurgical copper smelter\u201d will fail, unless methods are developed that can recover iron in a form that can be directly used by the steel or pigment industries.

Jan 1, 2017

By A. Banerjee, J. P. Weiler, J. Jekl, J. T. Wood, R. Berkmortel

"The work presented here is part of an ongoing project designed to develop predictive capabilities of the local mechanical properties, and thus, structural behaviour of a thin-walled high-pressure die-cast AM60B magnesium alloy component. This work focuses on developing correlations between process parameters and local microstructure. Numerical simulations of the die filling and solidification behaviour of the AM60B component were used to estimate local process parameters such as solidification rate, temperature gradient, filling velocity, etc. These estimated parameters were used to establish semiempirical correlations with measured VALUES (of the local microstructure measured in regions throughout the component of different solidification conditions. INTRODUCTIONHigh-pressure die-cast magnesium alloys are experiencing increasing use in structural automotive components. A strength-to-weight ratio comparable to steels and its ease of castability allow for these alloys to be utilized in such capacities as instrument panel beams, seat and door frames, and engine cradles, among others (Gjestland and Westengen, 2007). However, the current use of these alloys is limited due to variations in local mechanical properties. These local property variations restrict part designers to assume lower than actual properties, resulting in larger sections, thus diminishing the light-weighting advantages of magnesium alloys. If these local property variations could be predicted, part designers would be able to optimize die-cast magnesium alloy components and fully take advantage of the light-weighting capacity of these materials.The work presented here is part of an ongoing project aimed at developing predictive capabilities of the local mechanical properties, and bulk mechanical performance, from variations in local microstructure, and ultimately from local process parameters in die-cast magnesium alloys. This project, unique in its nature, is based upon the results determined from fifty sequentially cast AM60B magnesium alloy instrument panel beams provided by Meridian Lightweight Technologies (shown in Figure 1)."

Jan 1, 2012

By D. Van Tonder, C. Edwards

ABSTRACT Solvent extraction is used in many acid leach uranium circuits to upgrade and purify the uranium-bearing solution prior to final product precipitation. A number of strip options are available to recover the uranium from the loaded organic. This paper compares seven of these options on the basis of typical capital and operating costs for the solvent extraction circuit and downstream uranium processing and also considers other related issues. The aim is to provide an objective comparative assessment of these options that could be used as a qualitative guide in process selection or improvement.

Jan 1, 2013

By R. O. Burt

"IntroductionThe introduction to this section on gravity concentration indicated the wide range of equipment types that exist for the concentration of minerals, in what is the broadest size range of any concentration process.The equipment described in this chapter includes jigs, tables and sHme plant equipment. In contrast to the equipment described in the two succeeding chapters, this range of equipment, in nearly every instance, superimposes a mechanical movement on the fluid motion to effect separation of the valuable mineral from the waste mineral. The motion may be vertical Gigs), reversing (tables), or rotary (slime plants): however, in common they ""dilate"" the bed of particles to allow preferential settlement of the heavier particles.Description of Process UnitsJiggingJigging is the sorting of different minerals by stratification, based on the movement of a bed of particles relative to a fluid in a vertical plane.The basic construction of a jig is shown in Figure 1. Essentially it consists of an open tank filled with a fluid, normally water, with a horizontal jig screen at the top and with a spigot in the ""hutch"", or bottom compartment, for removal of heavies. The jig beri consists of a layer of coarse heavy particles (ragging) on the jig screen. This ragging is of a specific gravity between that of the minerals it is intended to separate.In operation the bed is made fluid by a pulsating current of fluid to provide stratification. On the upward or pulsion stroke the bed of ragging and slurry is normally Hfted as a mass, then as velocity of the upcurrent decreases it dilates, loosening the whole mass. On the downward or suction stroke it closes slowly again. The ideal is to control this dilation of the bed of material so that the heavier and smaller particles penetrate the interstices of the bed, while the larger heavies fall under a condition akin to ""hindered"" settling."

Jan 1, 1989

By A. Mcdonald, F. W. Breaks, T. F. Morris, S. A. Averill, D. C. Crabtree

Abstract-Gahnite, a zinc-bearing spinel, is a resistate mineral that may be used as an indicator mineral of polymetallic deposits in high-grade metamorphic terrain. The Ontario Geological Survey recently completed surficial mapping and sampling programs in the Separation Lake area of northwestern Ontario and Kinniwabi Lake area of northeastern Ontario in which gahnite was recovered from samples of surficial sediments. Ternary plots of the composition (ZnO, MgO, FeO[t]) of gahnite recovered from these surficial studies reveal three distinct groups: Group 1 is characterized by low (< 1 wt%) MgO values; Group 2 by higher (>1 wt%) MgO values; and Group 3 by higher FeO(t) values than Groups 1 and 2. The composition of in situ gahnite recovered from volcanogenic massive sulfide mineralization, Zn-rich Sedex-type mineralization and peraluminous rare-element mineralized granite and pegmatite also was determined. The composition of the gahnite obtained from surficial samples was compared with that of in situ material. Gahnite from the peraluminous rareelement granite and pegmatite overlapped very well with surficial gahnite of Group 1. Gahnite from volcanogenic massive sulfide mineralization and Sedex-type mineralization overlapped well with surficial gahnite of Group 2. These results suggest that determination of gahnite composition in indicator mineral surveys may be useful in exploration programs when assessing the mineral potential of a region.

Jan 1, 1997

By A. Mcdonald, F. W. Breaks, T. F. Morris, S. A. Averill, D. C. Crabtree

Gahnite, a zinc-bearing spinel, is a resistate mineral that may be used as an indicator mineral of polymetallic deposits in high-grade metamorphic terrain. The Ontario Geological Survey recently completed sur?cial mapping and sampling programs in the Separation Lake area of north-western Ontario and Kinniwabi Lake area of northeastern Ontario in which gahnite was recovered from samples of sur?cial sediments. Ternary plots of the composition (ZnO, MgO, FeO[t]) of gahnite recovered from these sur?cial studies reveal three distinct groups: Group 1 is characterized by low (< 1 wt%) MgO values; Group 2 by higher (>1 wt%) MgO values; and Group 3 by higher FeO(t)values than Groups 1 and 2. The composition of in situ gahnite recovered from volcanogenic massive sul?de mineralization, Zn-rich Sedex-type mineralization and peraluminous rare-element mineralized granite and pegmatite also was determined. The composition of the gahnite obtained from sur?cial samples was compared with that of in situ material. Gahnite from the peraluminous rare-element granite and pegmatite overlapped very well with sur?cial gahnite of Group 1. Gahnite from volcanogenic massive sul?de mineralization and Sedex-type mineralization overlapped well with sur?cial gahnite of Group 2. These results suggest that determination of gahnite composition in indi-cator mineral surveys may be useful in exploration programs when assessing the mineral potential of a region.

Jan 1, 1997

By Tom Shumka

"All mineral processing facilities that use girth gear driven mills need to inspect the gear teeth on a routine basis, whether it be every six months to every three years. The inspection frequency depends on gear tooth condition, and the objective is to ensure the operational integrity of the gear teeth. Conventional methods such as magnetic particle testing, visual inspection or dye penetrant examinations rely heavily on operator interpretation. At best, these techniques can determine whether a defect exists, but are unable to provide information on defect severity. This paper describes the use of combining combined eddy current array (eca) and alternating current field measurement (acfm) to provide a complete survey of all surface breaking indications on the whole gear tooth depth. This method accurately determines the size, length and depth of any cracks found on the surface.INTRODUCTION In order to gain a fundamental understanding of the evolving operational and production behavior of a piece of machinery over a specified time period as part of an effective condition monitoring program, a robust data collection process must be firmly established and adhered to. To be effectively implemented within an organization, a condition monitoring program must have support of not only the maintenance, production and engineering staffs, but also executive management support to ensure successful roll out to realize the maximum productivity of the machinery and subsequent cost-savings. One of the key elements of a mineral processing facility that use gear driven SAG Mills as a primary stage for grinding solution, is the integrity of the critical gear unit that drive the mill. For the maintenance team, condition monitoring on the gear unit is crucial for preventative maintenance. A catastrophic failure in the critical gear unit would require a minimum of ten days to replace the gear set, depending on the damage occurred. This, of course, would only be applicable if the client had a spare critical gear set in inventory. If a gear set had to be ordered, it could take from four months to two years to receive a new gear set. For example, in 2007, there was a global backlog of these types of gears sets resulting in a two year delivery. The maintenance costs associated with a catastrophic failure of this type would easily cost in the millions."

Jan 1, 2012

By Gurinder Kaur

Selenium (Se) based materials find wide applications in rectifiers, solar cells, photographic exposure meters, data storage devices, xerography and anticancer agents. They are also used in the glass industry to eliminate bubbles and remove undesirable tints produced by iron. In addition, Se is highly reactive towards a wealth of chemicals that can be potentially exploited to convert Se into other functional materials such as CdSe, ZnSe, Ag2Se. Here, we report a review of structural investigations of Se based materials in glassy and nanostructured forms. Glasses having varying amounts of Se and Tellurium (Te) were doped with group IV and V elements such as antimony and tin. Structural changes accompanying the composition variation were characterized with x-ray photoelectron spectroscopy, differential scanning calorimetry and x-ray absorption near edge spectroscopy. At the same time Se-Te nanoalloys were synthesized in aqueous micellar phase using Na2SeO3/Na2TeO3 as the Se/Te source. Morphology change from nanoparticles to nanoribbons was investigated using Scanning and Transmission Electron Microscopy (SEM/TEM) techniques. Structural investigations were also done for well defined morphologies of Se based nano-biomaterials obtained in the presence of water soluble protein bovine serum albumin (BSA).

Aug 1, 2013

"The Antamina orebody is a geologically complex, polymetallic skarn located in the Peruvian Andes. A range of copper and copperzinc ores are campaigned separately through the concentrator producing copper and zinc concentrates as well as lead and molybdenum by-products.Ore type classification at Antamina is based on chemical assays; geological or lithological variations are not considered. Consequently, each ore type demonstrates a wide range of concentrator performance.Antamina is currently implementing a system to track ore movements from the shovel face to the concentrator. Relatively sophisticated models of run-of-mine and coarse ore stockpiles ahead of the mill will be used to account for the variable delay between mining and milling.One of the numerous benefits of ore tracking is the ability to directly associate the measured concentrator performance with a physical location in the orebody. Using existing mine planning software, three-dimensional models can be created of such performance measures as metal recovery, concentrate quality, operating cost, and reagent consumption.Such a database of information allows the true value of different ore sources to be determined. The value of an ore source is conventionally measured as metal content (individual or combined ‘equivalent’) with a cut-off grade applied to indicate some base level operating cost. However, the true value of an ore source should include dynamic factors like haulage cost, reagent use, smelter penalties, and even prevailing metal prices. If an ore source is considered from all perspectives rather than simply its potential to deliver value, the concept of ore becomes more flexible. Any ore source that reveals itself to be unprofitable can be eliminated from the mine plan or possibly blended with others to improve its value. The ability to predict mill performance, and thereby profitability, is a powerful tool.In an operation such as Antamina, where managing ore sources, campaigns, and the delivery of a variety of concentrates in a narrow timeline to customers is a daily challenge, prediction is the key to success and improved efficiency."

Jan 1, 2005

By J. A. Relf

The construction of refineries and gas conservation plants in the general Edmonton area in the early 1950's made available large quantities of by-product liquified petroleum gases (LPG). These gases, together with discovery of increasing reserves of natural gas in the Edmonton area, provided Canadian Chemical Company with two of the necessities for petrochemical production, namely, available and reasonably priced raw materials and fuel. This paper outlines the development of the $83 million Edmonton plant from its origin, together with a brief description of the processes and some of the interesting features involved. Several economic aspects of the petrochemical industry are high-lighted including its importance to the local community and the province. The paper reviews the relationship between the oil and gas industry and petrochemical manufacturing and indicates some of the factors that may affect the future growth of the petro-chemical industry in Wes tern Canada.

Jan 1, 1962

By Marc C. Bétournay

A mine production locomotive, the world?s first applied industrial fuelcell vehicle, has been designed and tested in the context of a number of proof-of-concept projects supported by the Fuelcell Propulsion Institute, an international consortium of stakeholders dedicated to facilitate the commercialization of fuelcell vehicles. The locomotive?s simple electric-powered motor and controller system was ideal to study a number of requirements related to fuelcell power application: hydrogen power plant operation, underground hydrogen use, risk and regulatory requirements, production performance versus the conventional battery-powered locomotive version under measured duty cycles and production requirements, power plant design improvements for other fuelcell vehicles, and cost-benefit aspects. This article will focus on the design and testing aspects of this project which has led to successful performance demonstrations of the vehicle under surface and underground conditions at two mines. It will also present information on the creation of a safe, reliable and efficient power plant which fulfilled its design objectives, including longer productivity time for a given vehicle fill-up.

May 1, 2003

By J. Donovan

Underhand cut and fill mining is being planned for selected areas at the David Bell Mine where high ground stresses have resulted in particularly challenging mining conditions. In order to test the placement and performance of a variety of underhand cut and fill paste mats three different designs have been installed and extensively instrumented along the A-Zone 9C ore sill. The sill is approximately 87m long, 4.0m high, and 5.0m average width. The sill was broken into 3 sections each of which will contain one of the sill mat designs. The underhand sill will be mined 3.75mW x 4.0mH, allowing for some overbreak while minimizing the risk of the back span exceeding the design limit of 4.0mW. Each test sill mat includes pre and post-support and includes 0.5m (18?) broken muck mat placed along the sill floor. Upon developing beneath these mats quantitative and qualitative measures will be used to determine which design is the most suitable for application in underhand mining at David Bell.

May 1, 2007

By Georgia J. Lysay

The Kemess Mine tailings impoundment is retained behind an earthfill and rockfill dam that, when complete, will measure about 140 m in height with a crest length in excess of 1 km. Due to weak foundation conditions, the dam must be raised at a very flat downstream slope approaching 7H:1V. This requires an enormous volume of fill to construct the downstream shell of the dam, which has a low permeability clayey till core and is raised via the centerline construction method. For the initial years of annual dam raising, from 1996 through 2002, the downstream shell of the dam was constructed with non acid generating waste rock from the open pit, 7 km distant and requiring an uphill haul with obvious cost implications. To reduce costs, and to reduce waste haulage constraints on mining schedules, feasibility studies were initiated for raising of the downstream shell using cycloned tailings sand as opposed to open pit waste. This required inclusion of flotation cells for removal of residual sulphides from the tailings to produce the non acid generating product mandated for the downstream shell of the dam. These studies were positive, and cycloned sand construction was initiated in December of 2002. This paper describes the experience gained with cycloned sand construction for the dam. Unique aspects include environmental controls given the sulphide-bearing ores, preparation of the existing shell of the dam for subsequent placement of hydraulically placed cycloned tailings sand, on-dam settling ponds, water management issues, reclamation of the sand dam for erosion control commensurate with the wet climate, and use of the system to construct an above-water beach of non acid generating tailings to increase the closure security of the structure. A particularly unique aspect of the Kemess experience is hydraulic fill operations extending throughout the coldest winter months, as compared to other operations where such placement has traditionally been considered non-viable through the winter months

May 1, 2007

By T. P. Lim, N. K. Davé

"A modified accumulator method was devised to measure surface radon flux from porous media. It consists of a collector hood type of accumulator with a homogenizer pump and a pressure balancer. The latter was used to compensate any pressure changes produced during sample withdrawal and hence eliminate additional radon transport from the media. Errors resulting from radon back diffusion due to decreasing concentration gradient with time across the interface were also eliminated by measuring radon concentrations in the accumulator for two different periods of time and calculating the true radon flux, J(o), from the solution of a time-dependent radon transport equation in the absence of any pressure and temperature gradients.Core samples from the observation site were also withdrawn for laboratory determination of porosity, moisture content, bulk and grain densities, Ra-226 source concentration and the fraction of Rn-222 produced in the void volume. The data were used to calculate the radon diffusion coefficient for the media.Using the present method, the true value of surface radon flux for an abandoned uranium tailings pile was obtained as J(o) = 2020.2 mBq/m2/sec (54.6 pCi/m2/sec) compared to the value J = 1406.0 mBq/m2/sec (38.0 pCi/m2/sec) obtained by the conventional method. The bulk diffusion coefficient of radon for the media was obtained as 1.2 x 10-7 m2/sec.IntroductionRadon-222 (hereafter called radon) released from uranium mill tailings is a continuous source of environment radioactivity in terms of its transport as an airborne gas and its decay products. The particulate daughter products readily attach to aerosols or dust particles and can further be transported by various other environmental pathways. Typical radon release rates from existing tailings piles vary between 740 and 14,800 mBq/m2/sec (20-400 pCilm2/sec), depending on the nature of the tailings material, moisture content, etc. The United States Nuclear Regulatory Commission (NRC) is proposing radon release rates of 74 mBq/m2/sec (2 pCi/m2/sec) above that of background."

Jan 1, 1982

By C. O. Swanson

"OUR INTEREST in estimates of world reserves of lead and zinc is focussed mainly on the information they give about the sufficiency of metal supplies for the future. However, we soon realize that the estimates can be interpreted in several different ways. Accordingly, it is necessary to have some under-standing of the elements represented by a compilation of world re-serves, and we will start by examining the accuracy of the estimates and what they attempt to measure.Variations in Estimates of the ReservesIf we study the estimates of world reserves that have been published in recent years, we note immenediately that they vary over a considerable range. For example, an article by Shea in 1947 gave world reserves as about 36 million tons of lead and 60 million tons of zinc. Shea did not in elude the United States but I have added to his totals the estimates made by the Bureau of Mines for that country in arriving at the foregoing figures. For approximately the same date, the American Zinc Institute and the Lead Industries Association reported world reserves as about 50 million tons of lead and 77 million tons of zinc. A comparison of the two sets of figures shows a mean variation of 30 per cent. For individual countries the difference between estimates can be even larger. A few years ago the estimate of Canada's reserves made by the United States Bureau of Mines was 7.4 million tons of lead and 14.0 million tons of zinc, while the Gordon Commission reported 1 O. 7 million tons of lead and 26.0 mil-lion tons of zinc. In this case the mean variation was 55 per cent."

Jan 1, 1960

By J. Nesset, F. Rosenblum, P. Spira

"Sulphide concentrates may exhibit self-heating to various degrees during storage or shipping, the worst cases presenting a serious hazard from fire and SO2 emission. Based on measurements of heating rates on a wide variety of concentrate samples in a special apparatus, combined with field experience, a methodology has been developed which allows concentrates to be rated for their heating potential. This has proven to be very useful in practice, for example, in deciding on the need to take preventive measures. Oxidation under ambient conditions in the presence of moisture initiates heating locally within a stockpile. In the case of highly active materials, such as those that contain abundant pyrrhotite, heating may progress through three stages to temperatures well above 5000C. However, most concentrates show little or no propensity to selfheat. Heating rates were used to estimate values of the heat output, or self-heating capacity (in joules per gram), which sustains the process at each stage. Thermal data from differential scanning calorimetry are also reported. Variables which affect self-heating are discussed and an actual case of heating control on a stockpile by covering is described. A simple apparatus which can be used to simulate stockpiling conditions has been tested successfully and is proposed as a convenient test system.INTRODUCTIONPrevious publications from this laboratory on the evaluation of self-heating in sulphides dealt with tailings backfill (Rosenblum et al. 1982) and waste rock (Rosenblum and Spira 1995). Sulphide concentrates may likewise exhibit self-heating in storage or during shipping. In a comprehensive but dated review, Kirshenbaum (1 968) pointed out the conflicting nature of information on means of controlling the problem, particularly with regard to the application of water and ventilation. Modelling by Simpson (1 97 1) of autogenous heating in stockpiled zinclead concentrate and associated field measurements by Wright et al. (1972) showed that the supply of oxygen by wind and the shape of the piles were the major factors in the development of hot spots. Simpson did not attempt to explain the complex mechanism of self-heating, simply ascribing its onset to oxidation. Pearse (1 980) investigated a potential method of testing for selfheating which consisted of (i) reaction with hydrogen peroxide and (ii) differential thermal anal sis, to characterize the response of concentrates at both ambient and temperatures above 100 C. He found the method sensitive enough to identify the need for careful handling but not to predict ignition. He recommended compacting concentrates and covering stockpiles with plastic sheeting to prevent ingress of air. All these workers recognized the key role played by oxygen and moisture in triggering self-heating."

Jan 1, 2001

By D. Bouchard, M. Forté, A. Charette

A transparent replica of a casting die was built to achieve a better understanding of the filling mechanisms of aluminum in high pressure die casting. Water and tomato paste were respectively used as analogues for the Newtonian liquid aluminum and the non-Newtonian semi-solid aluminum. The transparent die was installed on an industrial casting press and filling was filmed with a high-speed camera. Differences between the Newtonian and non-Newtonian fluids are presented and discussed.

Jan 1, 2006

By Manqiu Xu, Pete Winn, Steve Wilson

"In the flotation of ultramafic ores at Thompson mill, Inco Limited, CMC is used as both a floatable rock depressant and electrostatic serpentine slime dispersant. CMC, being a high molecular weight polymer, creates a serious handling problem in its introduction into the flotation processes. Typically, it is added as a 1-3% solution. This requires an enormous handling facility and makes its metallurgical gains uneconomical.Laboratory studies have shown that dry CMC addition as opposed to wet addition is feasible, as long as sufficient conditioning time is provided. Dry CMC addition into the grinding mill is also possible but its effectiveness is slightly reduced as compared to dry addition after grinding mills. Dry CMC addition using a vibratory feeder into the mill discharge is successfully applied in the treatment of ultramafic ores at Thompson mill.INTRODUCTIONManitoba Division MineralogyAt Inco’s Manitoba Division, two distinctly different sulphide ores are processed at the Thompson mill - primarily by froth flotation. The Thompson and Birchtree mines are both located within the Thompson Nickel belt. Sulphide mineralogy is relatively simple and includes both hexagonal and monoclinic pyrrhotite, pentlandite and minor chalcopyrite hosted in metasedimentary and metavolcanic rocks. The significant difference between the two mines is the amount of ultramafic rock associations in the host material. Increasingly, more of the ultramafic associated ores from the Birchtree mine are being processed through the mill with a characteristic poor metallurgy."

Jan 1, 2000

By H. Henao, E. Kohnenkamp, L. Rojas

The slags generated in the copper conversion process are mainly composed of Cu2O-Fe2O3-SiO2 with the compounds CaO and Al2O3 in concentrations up to 10 wt%. The present work contributes to the knowledge of the conversion process, generating experimental data for the diagrams of phases Cu2O-Fe2O3- SiO2-Al2O3 and Cu2O-Fe2O3-SiO2-CaO. The experiments were carried out in a tubular furnace at temperatures of 1150°C and 1200°C under a condition of saturation with tridymite. Once the equilibrium was reached, the samples were fast quenched in water. The phases in the samples were observed in a Scanning Electron Microscope (SEM) and the elemental composition of the phases analyzed by means of Energy-dispersive X-ray spectroscopy (EDS) detectors. The addition of Al2O3 and CaO into the Cu2O-Fe2O3- SiO2 system resulted in an appreciable displacement of the liquidus lines, corresponding to an expansion of the liquid in the tridymite primary phase field. INTRODUCTION The conversion process of copper consists of oxidizing Fe and S present in mattes with 60 to 65wt% Cu (up to 16wt% Fe). This process is separated into two stages: 1- Slag blowing: Fe is oxidized, the addition of a flux such as SiO2 (silica) forms a second liquid phase called slag, this phase is removed from the furnace; 2-Copper blowing: in this stage, the matte with low concentration of Fe (<1% w/w) is again oxidized to remove S as SO2 in the exhaust gases. The product of these two processes is the formation of Copper Blister (> 98wt% Cu) (Schlesinger et al., 2011). Unlike the aforementioned conventional processes, in most Chilean smelters, conversion Peirce- Smith Furnaces are loaded with high copper matte (70–75wt% Cu) (Henao & Moyano, 2016). Due to the low concentration of iron in these matte (up to 5wt%), it is considered that separating the conversion process in two stages is neither operational nor environmentally convenient. Therefore, the process is carried out in a single stage (Pradena et al., 2006), generating a slag phase with a high percentage of Cu2O (wt%Cu>40).

Jan 1, 2019

By G. Herget

"A brief visit to European longwall mining operations in potash showed that retreating longwall mining provides a very attractive alternative to room-and pillar mining, especially in areas with bad roof, narrow seams and areas with high ground pressures. Mines de Potasse d&apos;Alsace, France converted all potash operations to longwall mining in 1980. Recovery rates per panel vary between 75o/~ to 85% which compares very favourably with Saskatchewan values. Ground pressure in Saskatchewan are comparable to those of some of the deposits in Europe, but the presence of water in the hanging wall of Saskatchewan orebodies has to be given serious consideration. However, given the mining experience in Saskatchewan and the improved technology f or laboratory and field investigations, a review of present mining practice in Saskatchewan is desirable. IntroductionLongwall mining is practiced widely in coal mining and allows complete mechanization. It is applicable at great mining depth, in thin seams, weak roof and has been applied recently even to coal bed s dipping more than 65 degrees. Ideally this system allows complete extraction of an orebody. However, with high mechanization and emphasis on obtaining high outputs per man shift, extraction ratios rarely reach more than 80010 per panel.France, Spain and the U.S.S.R. have had longwall operations in potash for some time and a brief description is given below. Two of the operations were visited and the Russian operation is described based on German literature"

Jan 1, 1986