Search Documents

By G. G. Hatch

FOLLOWING World War II there was an urgent need for the development of domestic sources of ilmenite to take care of the expanding needs of the titanium dioxide pigment industry. In addition, there was the interest by the pigment manufucturers and others in titanium metal. Prior to the war the pigment industry in the United States had obtained its major tonnage of ilmenite, analyzing 55- ?60 per cent Ti02, from India. However, as a result of the shipping situation which developed during the war, the pigment manufacturers had to consider the use of lower grades of ilmenite located on this continent .and several companies undertook extensive exploration programmes to locate and develop such orebodies. Probably the most significant deposit that was found as a result of these ?programmes was the orebody .at Allard Lake, Quebec, owned by the Quebec Iron and Titanium Corporation. This ?Company was formed in 1948 by the Kennecott Copper Corporation and the New Jersey Zinc Company to mine this ilmenite ore and treat it in electric furnaces to produce titanium dioxide slag for the pigment industry and iron for the steel industry.

Jan 1, 1956

By C. Larsen, I. Orford, L. Strah, M. Renaud, P. Radziszewski

"An AG/SAG mill was commissioned at the Brunswick mine concentrator in October 1998. This paper discusses the original shell top hat liner design for the bi-directional AG/SAG mill, observed liner wear, subsequent liner design modifications, and benefits.The original liners were chrome-moly steel Norsteel with rubber grates and rubber-lined pulp lifters. The design was based on experiences of other AG/SAG mills and recommendations by the liner supplier, Norcast. Liner design modifications were made in an iterative fashion after observing the wear rate profile of the liners; over ten liner sets were implemented. Shell liner design improvements were supported by a design of experiments approach in conjunction with discrete element method (DEM) charge motion simulations. Design optimization took into account lining costs and impacts on operating performance. The team approach to the liner design improvements process is described with emphasis on the application of the design of experiments. The liner wear history and mill operating performance are presented."

Jan 1, 2005

The stability of paste fill bulkheads forms an integral part of a successful paste fill system. Bulkheads are constructed at the draw points of open stopes to contain paste fill while the initial pour cures and forms a consolidated plug. Mobilization of uncured paste fill as a result of a bulkhead failure can lead to significant consequences, including endangering the safety of personnel, property damage and production losses and delays. The loading conditions in the paste fill and the resultant lateral loads on the bulkheads are complex and are dependent on many factors. This paper presents a case study of several paste fill bulkhead failures; the results of an in-situ pressure monitoring program to ascertain the pressure loads, and the subsequent paste fill bulkhead evaluation.

May 1, 2007

By Luke Keeney, Stephen Walters

"The start up of a new mining and metallurgical facility is a crucial step in the life of any mining project. The mining industries record is poor when evaluating processing plant operation relative to design capacity predictions made during feasibility studies. Multivariate geometallurgical orebody characterisation, using principle component analysis, is a method developed for improving predictive processing performance models during feasibility stages of mine development. This paper outlines the application of multivariate geometallurgical characterisation to the Cadia East deposit located in New South Wales, Australia. Cadia East is a low grade high tonnage copper-gold porphyry system in advanced stages of feasibility analysis. A dataset of ~32000 measurements and 150 comminution parameters (A*b and BMWI) has been used to develop class-based characterisation and modelling methodologies. The results of this study outline the development of class-based ore characterisation and provide a technique for analysing and interpreting large and complex geometallurgical datasets for prediction and optimisation of processing performance. The results enable sophisticated population modelling to be conducted which displays deposit scale processing variability, aiding circuit design specifications and predictions during feasibility studies.INTRODUCTIONA feasibility study is the major technical report on which the decision to proceed to production and on which financing is based (Shillabeer & Gypton, 2003). The mining industry’s record is not very good when actual construction time, costs, and operating performance are compared to the projections made in feasibility studies (Ballard, 1983; Gypton & Ward, 2000; Gypton 2002). A study by McNulty (1998) found that of 41 mineral processing and chemical plants built between 1965 and 1995, only 56% achieved design capacity within two years of commissioning and three were closed after failing to achieve design capacity within 36 months of start up (Shillabeer & Gypton, 2003). McNulty (1998) related this underachievement and failure of start up performance to the use of innovative process technology without appreciating and managing technical risk. Factors contributing to technical risk include inadequate pilot plant testing, scaled up prototype equipment without backup, design flaws and poorly understood complex process chemistry."

Jan 1, 2009

The goal of this presentation is to firstly, review mine effluent permits in a number of regulatory jurisdictions; and secondly, to develop a strategy for incorporating the regulatory requirements into the environmental assessment (EA) process for new mine proposals. The focus was on the province of British Columbia (BC) and their recent initiative on the One Project, One Process initiative. This task was approached by reviewing mine effluent permits for various regulatory jurisdictions and comparing them to BC mine effluent permits. This comparison revealed a variety of approaches for designing mine effluent permits, but there is a common scientific approach, which supports the conclusion that the permitting of mine site discharges can be designed based on a scientific approach. This approach is expected to: (a) achieve sound environmental protection, (b) demonstrate the application of Best Achievable Technology, (c) incorporate sound sustainability approaches, (d) incorporate regulatory objectives, and (e) create efficiencies for the regulator and mining industry. There is an essential precursor to developing a sciencebased effluent permit for which the proponent must provide: (1) the necessary technical assessment information to demonstrate the mine effluent permit application will result in an environmentally protective effluent discharge, to the satisfaction of the permitting agency; (2) the necessary level of detail for essential mitigation pollution control works to demonstrate how they will be operated to achieve the necessary treatment goals; (3) the necessary level of detail for non-treatment mitigation (passive treatment, or passive pollution control); and (4) the necessary level of detail to demonstrate how pollutants will be prevented from being mobilized (or being generated) from ore and waste materials, or, if the pollutant originates from an added milling reagent, how the reagent will be reduced. While (active) mitigation pollution control equipment is more definable in an effluent permit, non-treatment mitigation is more nebulous in terms of defining in a mine effluent permit; it is therefore recommended that appropriate management plans be developed for essential mitigation pollution control and non-treatment mitigation (passive treatment) and submitted with the proponent?s EA/effluent permit application packages. Major deficits in adequate active and passive pollution control will inevitably lead to regulatory impediments to developing a permit and allowing a mine to be developed, although EA processes strive to preclude major permit information gaps; the onus is on the proponent to provide complete information in this area. Hence the importance of EA processes ensuring that the major technical information requirements for effluent permit development are included in the EA phase. Recently, this aspect of the mine EA process has taken on a new role under the political efforts of One Project, One Review Process (Canadian) and One Project, One Process (in BC). These initiatives translate, in part, to ?synchronous permitting? (in BC): effluent permitting, for example, may be initiated shortly after the proponent submits the EA application to Ministry of Environment.

Aug 1, 2013

By H. Westengen

The AE alloy family exhibits remarkable combinations of properties when utilized as high pressure die castings. This performance relies on the fact that the rapid cooling rate resulting from the direct contact between the molten alloy and the steel die walls effectively refines the structure through rapid solidification. Furthermore, the rare earth additions modify the solidification pattern, dramatically reducing the solidification interval. A solid shell forms at temperatures exceeding 500C, reducing the tendency for die sticking and inverse segregation. As a result, the die castability is excellent, giving parts with a smooth and shiny surface. Unlike other magnesium die casting alloys developed to improve elevated temperature creep properties, AE alloys do not suffer from the commonly observed tendency to introduce brittleness. This feature is attributed to the fact that the massive magnesium- aluminium intermetallic phase is substituted by a finely dispersed lamellar structure of Al-RE intermetallics. The resulting combination of excellent elevated temperature properties and good ductility, as well as excellent corrosion resistance, means superiority of these alloys for demanding automotive engine and chassis applications.

Jan 1, 2006

By Dina M. Aloi

In today?s evolving and globalized world, mining companies are being pressured to move beyond compliance towards long-term sustainability and sustainable development. Companies are expected to ?engage? communities without a clear understanding of ?how? to do this or to what end. This move, away from compliance, develops more of a focus on ?Community? Social Responsibility and sustainability. This shift leads to the development of world-class projects that provide sustainable development for people, reduce the incidence of costly delays, and promote good global citizenship for companies. The process of ?engaging? communities in mining project design and development leads to a stronger license to operate, and a reduction in social and political risk. To create this mutually beneficial relationship between communities and companies, communities must be ?engaged? in the project development and risk assessment processes as early as possible, preferably during the exploration or the concept phases. How to create this ?engagement? and manage this risk will be discussed.

May 1, 2007

By Peter A. Hacquebard

"Two continuous coal zones occurring in a 2500f t (762 m) thick section of the Upper Carboniferous Pictou Group (Westphalian C and D) have been encountered in five offshore wells drilled f or oil and gas in the Gulf of St. Lawrence. They correlate, by means of fossil spores, with thick coals of the Mabou and Inverness coalfields situated at the eastern margin of the Basin. Therefore, the presence of a large submarine coalfield of at least 18000 sq mi. (46 620 km'] is indicated. This compares with an estimated size of 14 000 sq mi. (36260 km' ) for the Sydney Coal Basin.Accessibility is provided only by the small onshore parts of the Mabou and Inverness fields, because farther offshore the coals lie too deep to be mined (below 4 OOO f t ([ 219 m)).Two near-shore coal exploration wells indicate that at Mabou Mines the younger Inverness coals occur at a mineable depth to at least 5 km from land. A structure contour map of this area shows a reserve of 125 million tons in two Inverness equivalent seams that are 8.5 ft (2.6 m) and 4.5 ft (f.4 m) thick. The Mabou coals, however, reach too great a depth close to shore to possess mineable resources.A structure contour map of the Inverness submarine area, based on mine data and one off shore seismic profile, indicates inferred mineable resources of 160 million tons, in two seams that are 7ft (2.1 m) and 4.5 ft (f.4 m) thick . A detailed deep seismic survey will be necessary to substantiate the structure and resource estimates"",Maceral and coal quality percentage diagrams of five column samples of these seams (the 7 Foot and 13 Foot Seams of Inverness Equivalents) show a bright banded coal, high in reactive macerals, which will produce a weak coke unsuitable f or metallurgical purposes. A thermal coal with a rank of H. V. ""B"" Bituminous (0.64% Ro) is present, averaging 12000 btu llb (6 660 kcai/kg), 10% ash and 6% sulphur, of which 60 to 80% is derived from pyrite.Microlithotype profiles of the major Mabou and Inverness coals show characteristic successions that can be used f or seam identification and proved valuable f or structural interpretations.The time of faulting in the major fracture zone on the eastern margin of the Gulf of St. Lawrence Basin has been deduced from coal rank variations. It occurred in pos tPermian, probably Early Triassic time."

Jan 1, 1986

By G. Danha, D. Glasser, D. Hildebrandt, N. Hlabangana

"In this work, we apply a method known as the attainable region (AR) technique in order to optimize the milling and leaching process of a low grade gold ore. No work on the application of the AR optimization technique has been done yet on a joint milling and leaching process. The advantage of the AR approach lies in its ability to simplify the optimization problem, as searching over a defined set for the maximum of an objective function is a fairly standard procedure. The objective function we selected was that of optimizing a linear function of the value of the recovered material minus the cost of both milling and leaching. Using the three variables (milling time, leaching time and recovery), we constructed a 3D plot and used it to obtain all the possible recoveries from the different milling and leaching times. The optimum for our chosen objective was then found by overlaying a contour plot of the objective function on the 3D plot. Our results show that the optimum was obtained at 90 % recovery with a profit value of 600, milling time of 30 minutes and leaching time of 1750 minutes.INTRODUCTIONAfrican countries are facing a general increase in demand for electrical power. In South Africa, the demand is now surpassing the supply from ESKOM, the main electric power provider of the country. This has resulted in load shedding strategies being implemented in many local communities in an attempt by ESKOM to cope with the high demand. A potentially better approach is to propose use of energy efficient technologies in the country’s largest power consuming industry; the mineral processing sector.In mineral processing, milling is the highest consumer of energy. The objective of carrying out milling is not merely to reduce the particle size of the feed material, but also to liberate the constituent minerals that make up an ore. This is done so that valuable minerals can be separated from the gangue, in downstream processes, such as leaching. However, the milling process is generally performed relatively poorly, and at a considerable expense in terms of electrical power utilization. Tomanec and Milovanovic (1994) estimated that milling accounts for more than 50 % of the total power used in the concentration process, but this can rise to as high as 70 % for hard or finely dispersed and inter-grown ores. Apart from being relatively wasteful of energy, the milling process is also inefficient with regard to mineral liberation because of the indiscriminate nature of the grinding force."

Jan 1, 2016

By George M. Douglas

The southeastern shores of Great Slave lake present a curious anomaly in geographical and geological exploration, in that an area so large and important, and withal so comparatively accessible, should nevertheless have remained unexplored, unmapped, and indeed almost unknown, until quite recent" times On their return from the famous journey to the mouth of the Coppermine, the band of Indians with whom he travelled led Samuel Hearne across Slave lake. He was the first white man to see that great body of water and it is rather curious that it should have been seen first from the north rather than from the south. Hearne's account of the lake is vague, and he made no attempt ?to map the part through which he travelled. About 30 years later John Franklin, on his first journey to the Arctic, crossed the lake from the mouth of the Slave river to the Yellow Knife river. Franklin's maps show all of his route in accurate detail, except that part of it which lay through Slave lake. In 1833-34, Captain, afterwards Sir George, Back made the first exploration of the eastern end of the lake. Captain Back was then on his way to the Arctic coast by way of the Great Fish river, and his Indian guides led him through Great Slave lake by the route they had followed from time immemorial. This route, partly because of its directness, and partly because of its sheltered character, lay through the great mass of islands in the middle of the lake to the Talthei narrows, and thence along the sheltered north shore with its many coves and harbours. Pere Petitot made extensive journeys in Slave lake as well as other parts of the far north.

Jan 1, 1929

By R. Darlington, S. Ji

"High pressure die casting is a promising process to make thin-wall components with high dimensional accuracy and excellent surface quality. However, the non-uniformity is one of the important features in castings. The inhomogeneity in tensile properties and microstructural characteristics were studied for the castings with different thicknesses made by high pressure die-cast Al-Mg-Si alloys. For the local mechanical properties in the die-castings, the casting skin provided the highest, whereas the casting centre provided the lowest yield strength, UTS and elongation. The yield strength, UTS and elongation were significantly decreased towards the casting centre. The microstructural inhomogeneity is characterised by the segregation of coarse fragmented dendrites, the reduction of solute concentrations of Mg and Si, and the increase of porosity level from the surface to the centre of castings. The growth velocities of eutectic a-Al phase estimated using the Jackson-Hunt model confirm that the growth variation is larger in the thin castings than that in thick castings.INTRODUCTION Inhomogeneity is an inherent characteristic in as-cast microstructures of a variety of alloys because of their non-uniform chemistry, microstructure, defects, topology and the resultant mechanical properties in the different ranges of localization (Campbell, 2003). Generally, three types of inhomogeneities characterise casting microstructures, which include (a) the casting defects of shrinkage and gas porosity, misruns, cold shuts, inclusions, hot tears and hot spots; (b) the non-uniform microstructure from the surface to the centre of castings; and (c) the non-uniform microstructure from the dendrites grown from primary solidification and the structure formed during the subsequent eutectic solidification in inter-dendritic regions. The chemical composition and the morphology between the primary dendrites and the inter-dendritic eutectics also differ in the as-cast microstructure. Obviously, the inhomogeneity is different in the castings obtained from different casting processes."

Jan 1, 2018

By Juergen Antrekowitsch, Stefan Steinlechner

"Within the last decades, mainly the base metals, like zinc, copper and lead were recycled from different industrial residues without taking into account that accompanied minor side-elements are often also present. A high supply risk for critical raw materials derives mainly due to the high share of the worldwide production in a limited number of countries. Examples include indium and germanium in China, PGM in South Africa and Russia or cobalt and tungsten in the Democratic Republic of Congo. By taking the market of critical metals into account, the recycling of potential residues does not only contribute to an economic treatment but also to the European strategy to decrease the supply risk of certain metals. Depending on the metal discussed, political unrest, decreasing primary resources leading to supply risks in different countries or also simply economic interests moved these mentioned side elements and with this the residues where they are present in, into the focus of the recycling industry.Because of this, the typical routes of lead, zinc and copper production are evaluated concerning generated residues and their typical contents of contained minor elements. Finally, the paper tries to answer the questions how a possible treatment of these wastes could contribute to the overall supply of for example silver but also other minor elements."

Jan 1, 2016

By D. P. Bishop, G. J. Kipouros, R. L. Hexemer Jr., I. W. Donaldson, W. F. Caley

Aluminum powder metallurgy (APM) is an advanced metal forming technology frequently employed to fabricate complex structural components in a near-net-shape fashion. Exhibiting nearly 100% material utilization, APM continues to rise in popularity. Recent research initiatives in this field have emphasized the development and processing of advanced 2xxx and 7xxx series alloys. In particular, APM equivalents to wrought 7075 and 2024 have been sought. An overview of work completed in this area is presented. Included are data on the various production stages (powder compaction, sintering, forging, and heat treatment) as well as the microstructure and mechanical properties of the finished products.

Jan 1, 2010

By Mi, Dong Liang, Jingyuan Bai, Victor Zhou, Xujun

Squirrel cage induction motors are the mostly used motors at present. Currently, the rotors of the squirrel cage induction motors are produced by aluminum die casting technique with the advantages of low cost of rotors. It is well known that the copper’s electrical conductivity is around 40% higher than that of aluminum. If copper is used to replace the current widely used aluminum in rotors, the total loss of motors will be reduced, hence increasing the overall motor efficiency. Copper rotors can be used to produce high efficiency and even super premium efficiency motors without enlarge the motor frame size. Considering the huge quantity of motors, the die casting process is the best solution to produce copper rotor with economic cost. Because of the characteristics of copper, it is difficult to produce copper rotors by casting similar to that done in aluminum rotors. In order to improve the die casting quality of copper rotor, a new tooling structure was developed and the casting process of copper rotor was simulated and analyzed by Any-casting software. The filling process, solidification process, inner gas distribution and residual melt modulus were analyzed. It was found that the design of symmetrical runner and inner runner on both sides was helpful to reduce the impact of molten copper to the cavity surface during the filling process. The use of Slag traps array can reduce die casting defects inside the end rings. That will be helpful to improve the rotor quality. INTRODUCTION Squirrel-cage AC induction motors are most widely used in the world. In 2017, the total installed capacity of AC motors in China has reached more than 1.2 billion kW, and the annual power consumption accounts for about 60% of the total national electricity consumption. To improve the efficiency of squirrel-cage motor will be helpful to energy conservation and environment protection. There are several ways to improve efficiency of induction motors, using copper rotor is one of the most effective solutions. It is well known that the copper’s electrical conductivity is around 40% higher than that of aluminum. If copper is used to replace the current widely used aluminum in rotors, the total loss of motors will be reduced, hence increasing the overall motor efficiency. Copper rotors can be used to produce high efficiency and even super premium efficiency motors without enlarge the motor frame size.

Jan 1, 2019

By A. Hartikainen, M. Rinne, F. Johansson, R. Yorke, L K. T. Uotinen, E. Korpi, J. Antikainen

"In order to determine the in-situ shear strength of rock joints, large scale testing is required. However, this is both expensive and difficult to execute. One possible method to overcome this may be to use photogrammetry to capture large joint surface roughness in-situ and downscale it to replica samples, which could be sheared in laboratory. In this paper, as a first part in such a method, a technique to digitize surface roughness and to produce replica samples for laboratory shear testing from a larger joint sample are presented. First, a thin granitic rock slice with dimensions of 1.75 m x 0.95 m of granitic intact rock was chosen for the study. The joint surface is fresh and created through tensile induced splitting. The large joint sample is digitized using photogrammetry. Then, one fullscale 1.7 m x 0.6 m geometry is cropped from the digitized joint geometry and then subsamples at 10x, 7.5x, 5x, 2.5x and 1x scales. All sub-geometries are scaled down digitally to produce 0.17 m by 0.06 m geometries. The geometries are used to make casting molds both positive and negative to produce samples with perfect matedness. The casting molds are 3D printed in polylactic acid plastic and C60/75 concrete is cast to produce a replica series. In addition to the creation of this replica series, two pilot replicas are also tested using a portable shear box with a 0.5 MPa normal pressure. The results from the pilot rounds are presented and discussed. Finally, suggestions for future research are given.INTRODUCTIONThe rock mass strength is in many cases controlled by the shear strength of rock joints, especially in hard rock masses. The shear strength is generally found to be influenced by several parameters, including normal stress, the basic friction angle of the intact rock, the joint surface roughness, the joint wall compressive strength, the matedness of the joint surfaces, weathering and infilling. The effect of these parameters for the joint shear strength can be evaluated in laboratory scale. However, the shear strength is known to be scale dependent. How the scale effect influences the strength is not fully understood. The general consensus is that the shear strength decreases when sample size increases, i.e. a negative scale effect (Bandis et al. 1981). However, some studies have presented contradictory results, see for example Hencher et al. (1993) and Kutter & Otto (1990). The extent and nature of the scale effect is still a question of debate (Tatone & Grasselli 2013)."

Jan 1, 2015

By Jianglan Duan, Steve L. Cockcroft, Andre B. Phillion, Carl Reilly, Daan M. Maijer

"In the aluminum alloy wheel casting process, careful design of the cooling system in the die and its operation (cooling channel timing) are critical to achieve quality and productivity goals. The problem is challenging owing to the cyclic nature of the process and the relatively large thermal mass of the die in comparison to the wheel. For a given die geometry, a set of constraints have been defined to ensure directional solidification and an objective function, based on cooling rate during solidification, has been defined to reach a target secondary dendrite arm spacing. The methodology presented in this study employs the commercial finite element package, ABAQUSTM, and an optimization module based on the open source library, Scipy. The developed methodology has been applied to a series of geometries and cooling system configurations, including a 2-D axisymmetric wheel and die assembly generated from a prototype die. Preliminary testing has shown that careful selection of the objective and constraint functions have made it possible to reach desired solidification pattern.TM- Dassault Systèmes Corp."

Jan 1, 2014

By Michael Moats, Adirek Janwong

The use of cylinder electrowinning cells, such as emew® technology, for the recovery of silver from primary and secondary sources has been growing. In this study, common operating parameters used in silver electrowinning were evaluated for recycling applications. Silver powders were produced from an industrial solution in a laboratory scale emew® cell. A design of experiments was employed to evaluate the effects of HNO3 concentration, iron concentration, current density and solution flow rate on current efficiency, particle size, bulk density, and crystallographic orientation. Current efficiency was affected by each parameter with increasing HNO3 concentration having a strong negative effect, increasing iron concentration and current density having moderate negative effects and increasing flow rate having a positive effect over the ranges examined. Finer particles were produced with increasing current density and decreasing flow rate. Bulk density increased when HNO3 concentration increased. The crystallographic orientation of all powders was dominated by the (111) plane. Increasing flow rate decreased the relative intensity of (200) direction. Based on these observations, silver electrowinning in cylindrical cells can operate at high current efficiency and produce larger powders at low HNO3 concentration, low iron concentration, low current density and high flow rate.

Jan 1, 2014

By Jose R. Hernandez-Aguilar

"Three models to predict the effect of bubble size (Db) on metallurgical response were tested in a pilot-scale flotation column at Teck Highland Valley Copper mine. The column was fed with slurry collected from the Cu/Mo separation circuit. The first model was the one developed by Gorain et al. (1997), which assumes that the collection zone rate constant (kc) is inversely proportional to Db. The second model was the one proposed by Hernandez-Aguilar et al. (2010), which considers kc as an inverse square function of Db. The third model was the one developed by Yoon and Luttrell (1989) which provides expressions to describe the efficiency of particle collection (E) based on first principles. The results showed a significant bias between experimental and predicted data using the model of Gorain et al. (1997), possibly reflecting the model’s inability to explain the impact of bubble size, bubble rise velocity and flow regime on E. The model of Hernandez-Aguilar et al. (2010) well described the experimental evidence. The model of Yoon and Luttrell gave accurate and unbiased predictions. However, Yoon and Luttrell’s approach calls for a criterion to determine whether the flow regime is potential or intermediate, a subject that requires more fundamental research.INTRODUCTIONParticle collection, i.e., bubble-particle collision followed by attachment, is the basis of flotation. In a quiescent environment (such as the one observed in a column, or away from the impeller in a mechanical cell), a collision event can take place as long as the “degree of turbulence” caused by the rising bubble does not prevent particle and bubble to flow in close proximity. Upon collision, the particle slides on the bubble surface for a period of time. If the particle is hydrophobic, attachment occurs when the “sliding time” is longer than the “induction time”, which is the time required to thin and rupture the intervening liquid (usually water) film forming a three-phase contact angle. While the induction time is largely influenced by the degree of hydrophobicity of the particle, the degree of turbulence is governed by the bubble size. Generally, direct control of bubble size is not exercised by most mineral processing practitioners, in spite of its obvious importance. Studies to model the effect of bubble size on particle collection using fundamental approaches have been conducted (e.g., Anfruns and Kitchener, 1977; Webber and Paddock, 1983; Yoon and Luttrell, 1989; Dai et al., 1999). However, these models have been validated under highly idealized laboratory conditions (micro-scale experiments using single minerals and uni-sized bubbles), far from resembling those existing in practical industrial applications. Fundamental studies to interpret the effect of bubble size on particle collection in industrial environments are largely absent in the literature. Partly because of this lack of practical knowledge, many mineral processing practitioners perceive laboratory “bubble size” studies to be valuable academic exercises, but not something that can be directly applied to daily production issues."

Jan 1, 2011

By Hamid Butt

Information Technology ??Advanced Information Technology is dramatically changing information flow within organizations. This enables employees to have information at their fingertips to make informed and prompt decisions. ??Real-time information allows timely analysis, which dramatically reduces cycle times, making organizations faster and more flexible. Business Challenges ??Continual growth of mining and Mine mobile fleet.??Increasing maintenance costs. ??Difficult to identify and troubleshoot equipment problems while equipment is operating. ??New equipment is increasing in complexity and cost. Therefore, each failure results in a greater impact to production and cost. ??Troubleshooting practice is reactive. ??Protect and optimize the use of mining assets to realize maximum business value. ??Maintenance and Operating information is not easily accessible ?no near real-time system that provides complete information.

May 1, 2006

By K. Sun

The exothermic behavior of the intermetallic reactions inside an Al-Mn metallic powder compact and its assimilation fundamentals in molten aluminum were examined. In this study cylindrical compacts were manufactured and tested. The experimental work involved simultaneous temperature measurements of three thermocouples as well as detection of the apparent weight of the cylindrical specimen during its assimilation in liquid aluminum. The details of the intermetallic reactions prior to the compact complete disintegration were investigated by microscopically studying the morphology and local composition in a partially reacted compact. The variation of manganese concentration in the melt was determined by chemically analyzing the samples taken from the molten aluminum at specific time intervals. The exothermic reaction increases the compact's temperature above that of the liquid aluminum. In tandem with this exothermic reaction, the compact is suffering a swelling action. This swelling action disintegrates the cylindrical specimen, which is assimilated into the liquid aluminum. The intermetallic reactions proceed in a stepwise manner. Both the bath temperature and the compact composition impact on the exothermicity of the intermetallic reactions. However, when the amount of Mn in the compact is greater than 75-wt%, the maximum centerline temperature rise is slightly reduced as Mn amount increases.

Jan 1, 2004