Search Documents

By Markus Timusk

This paper describes a research project that focuses on developing a diagnostic routine to assist in decision support for the condition based maintenance of mobile mining equipment subject to unsteady duty. The objective is to develop a general method for initial identification of mechanical faults in machinery operating under non-steady state conditions. The platform to be used for the experimental development and validation of the system is the swing machinery in an electric mining shovel operating in an open pit mining environment. The strategic approach that is proposed for the diagnostic routine will involve using novelty detection augmented by temporal classification.

May 1, 2004

By D. Imeson, T. Grammatikopoulos, M. Aghamirian, M. Oliazadeh

"More than 70% of potash is produced worldwide by froth flotation. Flotation of potash was developed in the early 1930s. Amines are widely used for flotation of sylvite (KCl) from halite (NaCl) and insoluble materials such as clays. Amine collector is also absorbed by clays. Therefore, clays are usually separated by scrubbing and de-sliming prior to flotation. Alternatively, slimes can be floated ahead of potash flotation. Flotation recoveries of sylvite are commonly in the range of 85%, while losses can occur in slimes, flotation tailings and make-up of process brine. Ores containing free coarse-grained sylvite are generally screened, whereas both fine and coarse fractions are conditioned and floated separately. The unique features of potash flotation include solubility of sylvite in water, the size of particles floated and fast kinetics. Particles up to 2.3 mm can be floated and about 50% of flotation feed can be removed in the rougher stage in few minutes. The main challenges in potash flotation are the recovery of potash from slimes, flotation efficiency in the presence of carnallite and recovery of coarse potash grains. A review of potash flotation shows that there is still room for improvement in both coarse and fine potash flotation. The present paper reviews the most significant flotation parameters including reagent type and dosage, flotation circuits, flotation equipment size and new developments in potash flotation. The latter include new reagents, flotation technologies (Hydrofloat, Jameson and column cells) larger flotation cells and slimes flotation.INTRODUCTION Potash is the common industrial term for potassium in various chemical combinations and minerals soluble in water. About 90% of potash produced worldwide is used as agricultural fertilizers. Flotation is the main treatment process of sylvinite (KCl-NaCl) ores for recovery of sylvite (KCl). Potash concentrate should contain a minimum of 95% KCl and be relatively free from 0.2 mm KCl fines. The flotation process for beneficiation of potash ores was developed in United States and Russia concurrently in the early 1930s. In 1934, Potash Corporation of America applied flotation process in a commercial scale (Tippin R.B. and Huiatt J.L). In the initial application, halite (NaCl) was selectively floated by employing lead chloride as an activator and soap as collector. The sylvite concentrate was reported in the cell underflow."

Jan 1, 2012

By W. K. Buah, R. K. Amankwah

Waste-activated carbon generated by gold ore processing plants that employ carbon adsorption technologies may contain very high gold values and represent a potential source of extra revenue. In this research, two methods that augment combustion of waste-activated carbon are evaluated. These are mechano-chemical activation and charcoal-enhanced ashing. It was found that mechano-chemical activation caused structural transformation of the waste carbon, which resulted in a reduction in the temperature for complete oxidation from above 700oC to 450oC. Complete oxidation was also achieved at the same furnace temperature, for a combined sample of waste-activated carbon and 50% by weight of wood charcoal. In both cases, gold was extracted from the ash by conventional cyanidation, with recoveries greater than 98% from a head grade of 3.2 kg/t.

Jan 1, 2007

By T. Bhambhani, D. R. Nagaraj

"Ultramafic Ni ores present significant challenges in processing in that both recoveries and grades are not satisfactory, due to the presence of Mg silicates in large amounts. Significant quantities of xanthates and CMCs are generally used for their recovery by flotation. Additionally, given that some of these ores are processed under acidic conditions, CS2 generation due to xanthate decomposition presents some safety hazards. Technology to replace xanthate has been developed for which the safety and health issues are absent. Collector S-10294 shows significant improvements in Ni and overall S recovery at a dosing rate of one half that of xanthate. New polymeric modifiers have also been developed that help reduce the Mg content of the concentrates at very low dosages. The reagents are custom designed for use in normal or hypersaline water, and acid or alkaline conditions.INTRODUCTION The use of xanthates in sulfide mineral flotation is reported to have started as early as 1925 (Nagaraj 2005). The reagent is now ubiquitous in the mining industry, accounting for 40-50% of total collector consumption. In recent years, the development of more selective reagents has rendered xanthates largely obsolete in Cu flotation. However, xanthates continue to be sold in large amounts in the Au, PGM and Ni flotation industry, where bulk sulfide flotation is required. The low cost and easy availability is the largest driver for the use of xanthates in the minerals industry. Of particular interest to this study is the use of xanthates in the flotation of Ni sulfide ores. About 60% of the world’s annual nickel output is obtained from sulfide Ni ores (Hoatson, 2006). A strategically important category of these ores is the ultramafic hosted sulfides, such as those of Western Australia and Canada. These ores are characterized by low Ni grades (<1%), with the Ni minerals being pentlandite, violarite, millerite and mackinawite, and gangue minerals comprising an array of altered Mg silicates, mostly serpentines. The challenges associated with treating these ores are well documented (Eltham et al. 1973; Claridge et al. 1975). One challenge is that Ni recoveries from these ores are lower. This has been attributed to the increased pulp viscosity, as discussed in detail by Vasudevan et al., 2010. Additionally, Mg silicates tend to report to the concentrate in large quantities, which is problematic for two reasons: a) concentrate dilution, and b) the high melting point of Mg silicates tends accelerate wear on the refractory lining of smelters. This has been attributed to network transport to the froth phase via bubble flux and entrainment (Patra et al, 2010)."

Jan 1, 2012

By S. Junnikkala, K. Föhr

"Experiments were performed with plant feeds with a continuous 1,8 m3 cell at Pyhasalmi mine with Cu flotation feed in order to test the applicability of the bubble surface area flux as an indicator of the flotation rate constant. It was found that bubble surface area flux could not predict the rate constants of coarse Cu containing fractions. In the middle size fraction, the correlation coefficient in the rate coefficient estimation was higher but not statistically significant. Only the fine fraction showed a linear relationship with a moderate correlation coefficient.The bubble surface area flux was shown not to be a function of the impeller velocity above a threshold value. The flux was an almost linear function of the superficial gas rate enabling to use the superficial gas rate instead of flux if the operation of an existing cell is to be estimated.INTRODUCTIONBubble area flux seems to offer a simple way of modeling flotation. It relates the flotation rate constant with the bubble surface area flux by a simple linear equation. Due to this, there has been a considerable interest in using the bubble area flux for flotation computations. It has even caused claims that a cell producing a high bubble surface area flux automatically produces a high rate constant and therefore a high recovery.This paper discusses some of the assumptions of the relationship and gives some plant results during two sampling campaigns.The bubble surface area flux s b is describing the area of bubbles available for flotation in a cell per unit area. The bubble surface area flux is related to the superficial gas rate J, by the Sauter mean diameter as follows"

Jan 1, 2001

By P. Radziszewski

"The comminution energy curve is a profoundly simple graphical technique that displays detailed operating efficiency information for industrial comminution processes. The database underlying the methodology has recently more than doubled, to now contain a substantial fraction of the international comminution output (1.7 billion tonnes of rock per year) across more than 8 major commodities. This increase has deepened the analytical capabilities and effectiveness for assessing comminution circuit performance in relation to comparable operating mines. This paper will explore how the energy curve methodology can be used to examine the ability of stirred mill technologies to increase efficiency.Specifically, this paper explores how the energy curves methodology can be used to present energy efficiency gains achieved at three mines employing a stirred mill technology under different duties. The first of these cases studies was conducted by Rosa (2014) who compared the performance of two ball mills operating in parallel with a Vertimill in the regrinding circuit at the Samarco Iron project in South East Brazil. The Vertimill was found to achieve the same product specification while consuming 40% less energy. Brissette (2010) investigated the impact of grinding media on the performance of both ball mills and Vertimills. The energy savings achieved varied from 10% to 40% for the ball mills and 30% to 60% for the Vertimills. Lastly, Bergerman (2012) investigated the operating conditions of the Sossego regrind circuit from 2006 to 2011 against design specifications and laboratory testing. The operating work index of this circuit varied from 5.2 kWh/t to 44 kWh/t over this 5 year period. The full suite of energy curves"

Jan 1, 2016

Brunswick Mine employs an ore and waste pass system for material transfer. This paper reviews the evolution and performance ore pass systems at the mine. It presents the range of selected configurations, inclination, dimensions etc. Select case studies are used to address the influence of structure, stress and materials handling on the longevity of the employed ore passes.

Feb 1, 2008

By D. J. R. Ras

A sub-level open stoping method is being used to mine the massive deposits at TARGET Gold Mine which uses cemented tailings to backfill the stopes. This requires the construction of bulkheads to contain the freshly placed backfill, capable of resisting the hydraulic pressure imposed by filling. The bulkheads must contain an 8 metre head of backfill slurry within 48 hours and withstand the force exerted by a 35 metre load of consolidated fill at a maximum estimated fill relative density of 1.9. After a variety of methods of construction were evaluated, it was decided to construct the bulkheads using the low density, fast-setting foamed cement-based product TEKSEAL HS manufactured by MINOVA RSA. The cement foam is contained between low-cost steel and fabric brattices which are easy to construct, using a method specially developed for the TARGET bulkheads. The paper will describe the design, trialling and construction of the bulkheads, and results obtained to date.

May 1, 2007

By W. A. Lang

Introduction Under our present civilization, industrial developments will be greatest in those areas in which energy .can be most economically produced and efficiently used, where labour is in adequate supply, and where markets for the products of industry are available. A knowledge of fuels- the present major sources of energy- and of their utilization is therefore of vital importance. With that in mind, the aim in this paper will be to outline the known reserves of fuels in Alberta, to give their characteristics, to indicate the markets served by each, and to offer some suggestions for the future development of the coal industry. The paper should be regarded as a compilation of published data rather than as an original treatise. Alberta is richly blessed by having large reserves of mineral fuels. The estimated reserves of coal are 46,562 million tons. Alberta is the oil and gas province of Canada. The world&apos;s largest deposit of bituminous sand occurs along the Athabaska river in Alberta. In addition, there are large areas of forested land in the northern and western sections of the Province, and the rivers serve for the development of hydro-power.

Jan 1, 1949

By G. Belzil, F. Robichaud, M. Fullam

"The Goldex mining and milling complex is operated by Agnico-Eagle Mines Ltd. and is located in the Abitibi greenstone belt of Northwest Quebec, Canada. The mill operates presently at a throughput of 8,250 tpd with gold grade varying between 1.8 and 2.2 g/t. The ore is very high in gravity recoverable gold (GRG) at about 92% and as such a significant emphasis was placed on the gravity circuit. Commercial production started in 2008. Average gold recovery is 93.5% with about 68% of gold recovery coming from the gravity circuit. Over the course of the first several years of production, several gravity audits were carried out. In 2009, a complete gravity audit was completed, including ore, classification, Knelson Concentrators, and the gold room. In 2011, an audit was undertaken of the flotation circuit to determine the efficiency by which GRG is floated. Large samples of flotation feed and tails were collected and process for GRG content. This allowed a link between gravity and overall recovery to be made. This paper presents results of the audits and the development of a model linking gravity and overall gold"

Jan 1, 2012

By S. Koski

The Cerro Verde copper-molybdenum porphyry mine, majority owned and operated by Freeport- McMoRan Copper & Gold, is located 30 km southwest of Arequipa Peru. The concentrator, which produces copper and molybdenum concentrates, started operating in late 2006 with a 108,000 tpd design capacity, processing primary sulfide ore (mainly chalcopyrite and molybdenite). Plant capacity was recently increased to 120,000 tpd. The comminution circuit consists of one 60? x 113" primary crusher, four MP-1000 secondary crushers in closed circuit with dry screens, four 2.4m x 1.6m High Pressure Grinding Rolls (HPGRs) in closed circuit with wet screens, and four 7.3m x 11m gearless ball mills in closed circuit with cyclones. The HPGR circuit is fed by the Secondary Crushing circuit product at a T80 of 35 millimeters, and the HPGR circuit product feeds the Ball Mill circuit at a T80 of 3000 microns. This paper describes operating experiences with HPGRs during these first four years highlighting improvements in operating practices and presentation of data regarding operational efficiencies, also discussed are the primary benefits provided by HPGRs such as production of micro fractured particles, reduced ore Bond Work Index, and reduced power consumption. Cerro Verde represents the first installation of HPGRs in both the copper industry and large scale hard rock mining.

Jan 1, 2012

By H. Sipilä, H. Vartiainen, H. Paarma

"The carbonatite massif of Sokli includes several low-grade Nb showings composed of ores and wastes as identified by routine analyses. More detailed lithologic proportions were determined in two orebodies in the Kaulusrova Nb-mineralized area by a careful geological study and by thorium radiation measurement on 10 cm-long drill core cuttings with a total length of 460 metres. The distribution of Nb in eight X-ray spectrometrically analyzed drill core sample intervals (totalling 35.8 m) was determined by analyzing the intervals semi-continuously by an X -MET analyzer. The geological studies suggest that Nb-mineralized bodies are feasible fo r the sorting of are and waste. This was confirmed by the semi-continuous determination of Nb on the X-MET analyzer.IntroductionThe Sokli carbonatite complex is located in eastern Finnish Lapland. The main ore of the carbonatite massif is a regolithic phosphorus ore in the weathered crust. Large-scale geophysical measurements and diamond drillings have also established several niobium showings within the magmatic carbonatites. Owing to the complicated geology of the massif, the niobium showings occur as irregular zones o r areas displaying complicated structure, texture, mineralogy and geochemistry (Vartiainen and Paarma , 1979; Vartiainen , 1980). The tonnages in areas such as this are large but the grades in-situ are low . The most intensely studied niobium showing is the Kaulusrova area.The exploitation of these showings depends on the feasibility of applying a sorting technique to upgrade the feed and to minimize the amount of material to be treated in the concentration plant. These possibilities o n the Kaulusrova area have been viewed by a detailed geological and X-MET an analyzing study."

Jan 1, 1985

By K. G. Thorne, D. R. Lentz, A. F. Park

"The Main zone of the Clarence Stream gold deposit is hosted by a shear zone adjacent to the Saint George batholith in southwestern New Brunswick. The mineralization history relates to progressive deformation in the shear zone and the intrusion of the Magaguadavic granodiorite.Of three phases of deformation that have affected the area (D1-D3), D1 is not observed in the Clarence Stream shear zone. Two suites of igneous rocks intrude the shear zone: post-D2, pre-D3 gabbro; and granitic dikes, which crosscut the gabbros. Granitic dikes show a diverse range of relationships to D3 features, from pre-syn-D3 mylonitic fabrics in transposed and highly deformed enclaves, to nondeformed and entirely discordant dikes (post-D3).A variety of veins occur within this shear zone. Zoisite-bearing and later, crosscutting epidote-bearing veins are preserved as relics in quartz-mylonites, and predate quartz veins that host gold mineralization. The epidote-bearing veins are associated with pseudotachylitic cataclasite dikes, consistent with transient brittle failure during ductile deformation.Deformation relates to right-lateral strike-slip motion across the shear zone, and subhorizontal and near-vertical stretching lineations imply transpression. A late (late- or post-D3) dip-slip phase of motion is also apparent, and cooling followed a metamorphic peak early in D2-D3 history. Deformation of the shear zone, and more localized transient brittle failure, provided the permeability for fluid movement and vein emplacement. This scenario is similar to the findings of other studies, in which geochemical, tracer isotopic, and age-dating (U/Pb, 40Ar/39Ar) results suggest that the adjacent Magaguadavic granodiorite provided heat and metals. La zone principale (Main zone) du gisement d’or de Clarence Stream est encaissée par une zone de cisaillement qui longe le batholite de Saint George dans le sud-ouest du Nouveau Brunswick. L’historique de la mise en place de la minéralisation accorde un rôle important à la déformation progressive dans la zone de cisaillement et à la mise en place de la granodiorite de Magaguadavic.Des trois phases de déformation à avoir affecté la région (D1-D3), les effets de D1 ne sont pas observés dans la zone de cisaillement de Clarence Stream. Deux suites de roches ignées se sont mises en place dans cette zone de cisaillement : un gabbro post D2, pré-D3 et des dykes granitiques qui recoupent le gabbro. Les dykes granitiques montrent une grande diversité de relations avec les structures D3, allant de précoces à synchrones aux fabriques mylonitiques D3 dans des enclaves transportées et fortement déformées à des dykes complètement discordants et non déformés (post-D3).On note diverses veines dans cette zone de cisaillement. Des veines contenant de la zoisite ainsi que des veines d’épidote sécantes plus tardives, lesquelles sont préservées comme reliquats dans les mylonites à quartz et sont plus vieilles que les veines de quartz contenant la minéralisation aurifère. Les veines d’épidote sont associées à des dykes de catacalasite à texture de pseudotachylite, compatibles avec une rupture cassante épisodique durant la déformation ductile.La déformation résulte d’un mouvement décrochant dextre le long de la zone de cisaillement et les linéations d’étirement subhorizontales et quasi-verticales impliquent de la transpression. Une phase tardive (tardi- ou post-D3) de mouvement selon le pendage est aussi apparente, et le refroidissement succède à un pic métamorphique tôt dans l’histoire D2-D3. La déformation de la zone de cisaillement et la rupture cassante épisodique ont fourni la perméabilité nécessaire au mouvement des fluides et à la mise en place des veines. Ce scénario est similaire à celui proposé par d’autres études, dans lesquelles les résultats de géochimie, de traceurs isotopiques et de géochronologie (U/Pb, 40Ar/39Ar) suggèrent que la granodiorite de Magaguadavic avoisinante a fourni la chaleur et les métaux."

Jan 1, 2008

By R. R. Klimpel

"SYNOPSISA discussion of the importance of flotation rate in the analysis of mineral flotation is presented. In particular, the highly interactive nature of the flotation ""system"" is emphasized where there are components of chemistry, equipment, and operating conditions simultaneously involved. It is further shown that: 1) flotation rate must be measured in order to economically optimize the performance of an industrial flotation circuit, 2) that consistent patterns exist in both flotation rate and equilibrium recovery when changing various settings of the system components, 3) that knowledge of these patterns is necessary in order to avoid making system changes that are either self-compensating or dramatically re-enforcing in some particular aspect of performance, and 4) the rate related role of the chemistry component (e.g.frothers and collectors) is often much bigger than is sometimes realized (especially in a negative sense involving overdosing of reagents). INTRODUCTIONFroth flotation is widely usedl-6 in mineral beneficiation processes as a method for separating different types of finely divided solids present in a liquid (usually aqueous) suspension. The approach is based on the contacting of solids with upward moving air bubbles in an agitated vessel where the solids are exposed to chemicals (collectors) which create a condition favoring the attachment of a certain portion of the solids to the air bubbles. This selected portion is then removed in a froth stabilized by chemicals (frothers) and subsequently recovered from the flotation vessel. Depending on the settings of the various components of the flotation ""system"" (see Figure 1) it is possible to achieve a wide range of flotation performance."

Jan 1, 1984

By Donald Leroux, Ralph Dahlke, Dave Scott, Finch. James A., Cesar O. Gomez

"The efficiency of the flotation process depends on how effectively air is dispersed into small bubbles. Bubble surface area flux - the surface area of bubbles per unit time per unit cross-section area of a cell - is emerging as the parameter to characterize gas dispersion. One of the approaches proposed to measure bubble surface area flux in industrial cells is based on the measurement of two variables: gas velocity and gas holdup, using separate sensors. Plant testing of the gas velocity sensor gave evidence of a series of operational problems which may be necessary to correct before attempting to characterize gas dispersion. Problems such as uneven air distribution within a cell and along a bank, faulty air and slurry valves detected during attempts to redistribute air, and poor control of pulp level and gas flow became evident. Detection of these problems from gas velocity measurements is illustrated.INTRODUCTIONBubble surface area flux is considered a key variable in the optimization of flotation circuit performance (Gorain et al., 1997; 1998). The Mineral Processing Group at McGill University has devised and developed a method for estimating bubble surface area flux in industrial flotation cells (Finch et al., 1999). The method is based on measuring gas holdup and superficial gas velocity using two separate sensors and applying drift flux analysis to estimate bubble size (Dobby et al., 1988; Banisi and Finch, 1994). With bubble size and superficial gas velocity known bubble surface area flux can be calculated.This method was selected by Noranda to characterize gas dispersion in cells as part of a program to model and optimize flotation circuit performance. However, initial testing at Brunswick Mine with the gas velocity sensor provided some unexpected results indicating operational problems and equipment malfunctions that needed to be addressed before systematic measurement of gas dispersion could be initiated.The subject of this communication is to illustrate the detection of these problems from gas velocity measurements. The line 3 Zn Cleaner circuit comprising four stages of Denver DR cells was the main subject of analysis, including the effect of correcting these problems on the metallurgical performance of the Zn 3rd cleaner bank of ten DRl 00 cells."

Jan 1, 2001

By M. Y. Levesque

The Australian Government?s Energy Efficiency Opportunities (EEO) program launched in 2006 obliges companies that use more than 0.5 PJ (petajoule) or roughly 139 GWh (gigawatt hour) per year to conduct an energy assessment in order to identify measures to improve energy efficiency. The opportunities identified by the mining sector were assembled in the Mining Significant Opportunities Register that permitted companies not yet embracing and adopting an energy management program to see what those who are, were doing and how much energy was saved, and helps disseminate best practice. The measures can be filtered by company, year, category or equipment type. The creation of a central repository of energy efficiency initiatives is valuable but this existing database could be improved; fields identifying the energy and carbon emission savings associated with a given initiative are a surprising omission. Consequently it does not permit the relative effectiveness of different measures for energy and carbon reductions to be readily assessed. A review of energy management efforts implemented in the mining industry, published in peer reviewed journals, corporate sustainability reports or industry publications during the last 40 years has revealed many examples of best practice. However, the lack of a standardized reporting framework in any of these sources has made it difficult to assess the effectiveness and compare the adopted energy management measures ? just as is the case with the Australian register. In an attempt to address these issues, an improved database structure has been created for energy management measures from the mining industry which identifies energy and financial savings arising from energy management initiatives, classifies applications to specific processes or equipment, and recognizes leaders in the mining industry with respect to energy management. The structure of the register includes the key data relevant to energy management in mining that is absent in the Australian version. The mining industry energy management database has been made available in the public domain where stakeholders can examine the best practice examples. Mining energy champions may also contribute to the register by providing case studies; a standardized entry template affords a quality assurance dimension that is absent in other reporting initiatives. Adoption of this database with its standardized reporting mechanism will enhance transparency of the mining industry in energy matters and help it maintain its social license to operate.

Aug 1, 2013

By J. A. Finch

"A method of sampling and presenting bubbles for imaging for use in full-size flotation cells is described. The device (bubble viewer) comprises a tube attached to a sealed glass viewing chamber. The assembly is first filled with frother-containing water (to prevent coalescence) and the tube immersed at the desired location below the froth. For a few minutes bubbles are collected in the viewer free from slurry and are readily imaged. To reduce bubble overlap and the problem of defining the plane of view, the viewing chamber has a sloped side. Bubbles rise, encounter this slope, spread into a single plane and slide up. This simple expedient virtually eliminates overlap and provides an unambiguous focus plane - the underside of the sloped glass. The bubble image is captured and processed to give size data. The bubble viewer has been employed at several concentrators on different types of flotation cells. Examples of the images are given. The impact of position in the cell and the effect of changing gas rate on bubble size are illustrated. This technique provides a sensitive measure of the effects of process variables on bubble size.INTRODUCTIONDespite the extensive use of flotation in the mineral processing industry, the methodology employed for cell design is largely based on empirical rules rather than on first principles. One of the main reasons for this state of affairs is that the local flow structures encountered in industrial-scale machines are very complex. These flow structures are difficult to simulate under the controlled conditions of the laboratory and the difficulty to solve the mathematical models that treat the randomness of such flows also mean theoretical treatment is limited. Understanding flotation cell hydrodynamics requires reliable data, which involves the implementation of measurement techniques capable of performing both at the laboratory- and the industrial-scale, In addition, it is desirable that such techniques are amenable to automation to reduce extensive manual intervention in the data collection process."

Jan 1, 2002

By Gus Van Weert, Peter Kondos

"Ore sorting has been quite successful in providing a separation means in the rock size range of 1 to 6 inches; a range where mineral dressers do not have many options. The industrial minerals and recycling worlds have embraced this technology. However, ore sorting has not found wide application in the base or precious metals mining industry. One reason for this is thought to be the reliance of most sensors on rock surface characteristics, not very useful in case of sulphides, non-existing in case of gold. Microwave heating, however, is specific for sulphides and graphite (or carbonaceous matter) embedded in the rocks; washing or even drying does not appear necessary. Separation can be done afterwards by already existing ore sorting technology using infrared sensors. Test results on six Nevada gold ore samples are presented in detail. Some simple test procedures are also presented for those wishing to explore the microwave potential of sulphide sorting in their own operations.INTRODUCTIONMineral processing in the base metals industry most often involves upgrading of the ore, concentrating the valuable mineral fraction by classic methods, such as flotation. Since the liberation of minerals in the ore occurs mostly at or below the 100 micron level, the industry has been living with fault lines, so to speak, between blast hole spacing (10,000 mm), run-of-mine ore size (100 mm) and beneficiation size (0.1 – 0.01 mm). The acceptance of ore sorting will inevitably lead to the revisiting of the following questions: “Exactly how much below ore grade rock ends up in the mill because the geologists or the miners cannot define the resource boundaries more precisely? How can the economics of dilution be improved? How many ore grade rocks are lost with the overburden?”"

Jan 1, 2007

By Robert B. Parsons

"The Canadian mining industry is not off to a good start in the 1993/94 budget season. Of the five provinces and territories to table budgets as of March 31, 1993, the industry&apos;s scorecard shows: one win, one tie, and three losses.IntroductionBy the end of March, five of Canada&apos;s twelve provincial and territorial governments had tabled their 1993/94 budgets. The mining industry is off to a bad start. The industry&apos;s scorecard shows one win, one tie, and three losses. Only Newfoundland appears to be paying any attention to the industry&apos;s concerns about the impact of taxation on competitiveness. It is particularly disconcerting to see that non-profit based taxes continue to increase, at a time when these taxes are the focus of a united attack by the entire industry.NewfoundlandFirst, the good news. On March 18, 1993, Finance Minister Winston Baker announced the following changes to the province&apos;s mining tax regime:"

Jan 1, 1993

By D. G. Sinclair

In any discussion on the subject of mine-safety, it is well to honestly face the fact at the outset that mining is a hazardous occupation and that certain inherent dangers attach to the work, which, in spite of the greatest vigilance on the part of everyone concerned, will from time to time exact their toll of in jury or death from the underground worker. Great progress has been made of late years in narrowing down the range of these necessary risks, and, illustrative of what can be done along these lines by concerted effort, it is pleasing to read from time to time of large operating mines running for weeks, months, a year or more, without a single lost-time accident. To achieve any results in the work of accident prevention it is necessary, first, to have a definite goal, such as a no-accident period, be it a week, a month, or a year, to aim at; and, second, to set up definite standards to work by. The legal code of regulations should form the basis of all standards of work at every mine and should, for this reason, cover as far as possible all conceivable phases of operation. This represents the ideal, but in practice it is unattainable, largely because of the many variables that must be considered, due to the divergence in the scale of operations and to differing geological conditions at the different mines. Hence it becomes necessary for the operator who wishes to attain the maximum in the establishment of high standards of safe operation to so amplify the code as to meet the peculiar requirements of his operation.

Jan 1, 1930