Search Documents

By I Brunton

Blast fragmentation can have a significant impact on the profitability of a mine. An optimum run of mine (ROM) size distribution is required to maximise the performance of downstream processes. If this fragmentation size distribution can be modelled and controlled, the operation will have made a significant advancement towards improving its performance. Blast fragmentation modelling is an important step in Mine to MillTM optimisation. It allows the estimation of blast fragmentation distributions for a number of different rock mass, blast geometry, and explosive parameters. These distributions can then be modelled in downstream mining and milling processes to determine the optimum blast design. When a blast hole is detonated rock breakage occurs in two different stress regions û compressive and tensile. In the first region, compressive stress waves form a æcrushed zoneÆ directly adjacent to the blast hole. The second region, termed the æcracked zoneÆ, occurs outside the crush one. The widely used Kuz-Ram model does not recognise these two blast regions. In the Kuz-Ram model the mean fragment size from the blast is approximated and is then used to estimate the remaining size distribution. Experience has shown that this model predicts the coarse end reasonably accurately, but it can significantly underestimate the amount of fines generated. As part of the Australian Mineral Industries Research Association (AMIRA) P483A Mine to MillTM project, the Two-Component Model (TCM) and Crush Zone Model (CZM), developed by the Julius Kruttschnitt Mineral Research Centre (JKMRC), were compared and evaluated to measured ROM fragmentation distributions. An important criteria for this comparison was the variation of model results from measured ROM in the fine to intermediate section (1 mm to 100 mm) of the fragmentation curve. This region of the distribution is important for Mine to MillTM optimisation. The comparison of modelled and Split ROM fragmentation distributions has been conducted in harder ores (UCS greater than 80 MPa). Further work involves modelling softer ores. The comparisons will be continued with future site surveys to increase confidence in the comparison of the CZM and TCM to Split results. Stochastic fragmentation modelling will then be conducted to take into account variation of input parameters. A window of possible fragmentation distributions can be compared to those obtained by Split. Following this work, an improved fragmentation model will be developed in response to these findings.

Jan 1, 2001

By D Thomas, B Gallagher

Valuable data for geotechnical interpretation and integration into effective Australian underground mine planning may often be available, yet is not always fully appreciated or utilised, particularly in the early stages of mine planning or in due diligence studies. There may be considerable benefits associated with early prioritisation of geotechnical evaluation and impact on mine planning. Unidentified, misinterpreted, or ill-defined adverse geological and related geotechnical resource characteristics can pose significant business risk to underground coal projects and operations. Preliminary resource definition in the early conceptual mine planning stages attributes significant focus (entirely warranted) on resource quality and structural geology constraints. Yet detailed geotechnical data analysis and interpretation, which may have a substantial down stream impact and sensitivity with respect to future mine planning strategies, at times is given lower priority, or scoped and resourced in the later stages of a bankable feasibility study. Through extensive mine planning experience and observation of downstream process impacts, it has been found there is often data available for geotechnical analysis that does not readily stand out or is not adequately understood or utilised, available at the early (conceptual) stages of mine planning. Part of the issue may be that exploration geologists are not necessarily experienced geotechnical engineers and do not necessarily recognise or understand all important parameters. Subject to appropriate application of experienced professionals data can be manipulated to provide key geotechnical hazard assessment at minimal cost, and provide a framework for understanding and optimising the mine planning process. Although there is no single prescribed strategy for resource evaluation from a geotechnical perspective, potential business risks and mitigation approaches can and should be adopted at the conceptual mine planning stage. There has been a recent focus in the metals industry to provide a reporting framework for geotechnical classification of mining projects. This paper outlines the strategies and gives examples of key analyses adopted in mine planning and discusses the relative merits of adopting a reporting framework as a tool for geotechnical classification in mine planning.

Jan 1, 2005

Topography, location of coal bearing land and existing built-up areas severely restrict locations for overburden disposal and dumping sites north of the Latrobe River clear of the coalfields are assumed until internal dumping areas can be established.

Jan 1, 1982

By Montagnon P, Dagois G

The use of activated carbon for gold recovery has been known for years, but came industrially on stream since the years seventies.Despite several years of experience, the criteria for selecting a carbon have not been clearly determined so far.This paper will try to highlight the user through his experience, on the most important factors which should affect his decision.We will develop:- Physical characteristics - Adsorption characteristicsand try to show that slight variations on these characteristics may have important consequences on the plant design and profitability.

Jan 1, 1984

There are a number a stages in a project at which an audit must, or should, be undertaken. An independent audit may be necessary for the comfort of directors and/or financiers before the major finance is committed, but an internal pre-development audit is the opportunity for the management team to take stock of the project and reaffirm their confidence and commitment. Maxims for project success are given and a check list for pre-development audits is presented. The need of mid-development audits may arise and their brief will depend on the circumstances arising. A game theory approach to decision-making is demonstrated in which the alternative of fast-tracking a development is considered. At the conclusion of the project, before the team is disbanded, a post-development audit should be made. Valuable learning can come from this process which could give important guidelines for future projects and a check list is presented.

Jan 1, 1997

A real Dorothy Dix title has been selec- ted for this paper. It has the advantage, however, of being capable of being interpreted in many different ways and hence I can select my own approach. You probably are thinking that this topic would be more appropriately handled by an Accountant. I wish to make it clear at the outset that I am not skilled in the sometimes mysterious ways of Accountants - likewise that profession frequently has difficulty in pinning down economists. We have our own strange ideas about profits, marginal efficiencies, cost/benefit analysis etc. What follows is in the main a mixture of two disciplines, probably in a form that few of the purists from either side would accept. Nor do I expect the reader to accept my own prejudices. The paper is designed to stimulate thought and discussion'on the subject. Emotive words such as "profit" and "loss" make for wide differences of opinion. At the time of writing there is a surprising degree of acceptance of the viewpoint that profits in Australia are too low and one is tempted to make this point of near agreement a starting Point.

Jan 1, 1975

In this paper, a subtle, but important, difference has been drawn between responsibility and mandate. Responsibility has a connotation of financial involvement assigned to an organ- isation as a result of some action it takes, the ramifications of which can be ascribed directly to the organisation. In contrast mandate relates to the power and authority to act. The paper outlines the role of poli- ticians as community decision-makers and the need for Government policy to be flexible in an advanced industrial society so that decision- making options are kept open for as long as necessary. Further, broad community objectives need to be understood and defined so that plans and policies can be consistent. Co-ordination through communication at all levels, especially at the public administration interfaces and with the private sector,is essential for effective resource allocation and efficient implementation. The paper discusses several aspects of the infrastructure responsibility question and some considerations which might be viewed as important by the community decision-makers in considering what responsibility the "community" should accept in providing infrastructure.

Jan 1, 1974

By Forster G, Datta P. K

Many high temperature industrial processes involve gaseous halogen-bearing environments. Essentially, these fall into three subject areas: power generation, waste incineration and especially extractive metallurgy. Fundamental to any understanding of the process chemistry and efficiency in the process technology is an adequate knowledge of background thermodynamics relating to metal-chlorine reactions. In this context, existing free energy/temperature diagrams for metal chlorides do not include many elements, in particular the so called refractory elements from Group V and Group VI of the Periodic Table, namely niobium, tantalum and vanadium, and molybdenum. This paper reports estimation and calculations of the free energy values for these chlorides. The data is discussed in the context of high temperature chlorination processes.

Jan 1, 1991

A portable surface impedance meter has been tested extensively over a wide variety of geological formations both in Australia and elsewhere. It has proved a useful geophysical too] for relatively shallow mapping (i.e less than 100 metres depth) of faults, intrusions, dykes and conductive ore veins and can be used as a depth probe for overburden and glacial ice. Case studies involving coal seam mapping at Collide (Qld. Australia), galena ore vein location at Zeehan (Tas. Australia) and glacial ice probing on the Brewster Glacier (South Island, New Zealand) are detailed. The first results of a similar unit using a lower frequency with consequential increase in depth of penetration will be presented. The application of VLF measurements to monitor blasting in mines and in the location of earthquake epicentres will also he introduced.

Jan 1, 1987

This paper describes how Western Mining Corporation uses sophisticated diesel equipment in mining of shallow flat dipping narrow ore- bodies in the Otter Juan area. Though in most cases the stoping method chosen relies on hand held conventional equip- ment, the 'ore handling systems have been designed to allow for a relatively high degree of mechanization. The use of diesel loaders, trucks along with three boom jumbos is described. A single one in nine decline driven as the means of access to the various ore surfaces at Otter/Juan resulted in the first ore being produced first 15 weeks after the first round was fired in the Ore-Decline. Now, three years later, the.mine is in full production, and in 1971/72 produced 392,000 dry tonnes of high grade Nickel Ore.

Jan 1, 1973

Tyre cost at Mount Morgan Limited had been 24% of the truck operating cost. Comprehensive tyre testing resulted in a reduction in tyre costs of about one third. A record of the evaluation techniques may enable the selection of tyres that are most suited to particular conditions. Rubber characteristics, rubber quantity, tyre design, road conditions, dump conditions and inflation pressure were found to be sig- nificant variables. Measurements of tyre temperatures at the breaker strip were used to select the tyre design and inflation pressure required for Mount Morgan Limited's conditions. Relugging of tyres was discontinued as a result of tyre testing.

Jan 1, 1974

Full aerodynamic design development of the proposed fans for the enlarged primary ventilation system at Mount Isa Mines Limited was initiated before tender specifications were prepared. Theoretical and analytical design studies were made of many possibilities to determine the optimum proposal. Major considerations were efficiency, simplicity, standardization, and mechanical feasibility. Model testing and experimental work covered blading design, inlet shape, diffuser and tail fairing dimensions, instrumentation requirements, ancl noise studies.Theoretical and predicted performance estimates were prepared for the three 20 ft diameter vertically mounted axial flow fans.

Jan 1, 1967

By X Yang

White phosphorus (P4) is a critical element in industry, but its current production from phosphate rock using the carbothermal reduction method raises significant environmental and health concerns. This pressing issue necessitates the development of new technologies that facilitate the sustainable production of P4. In response, my team is actively developing an innovative, coke-free approach for white phosphorus production. This method involves the dissolution of phosphate rock in molten CaCl2, followed by the extraction of P4 through electrochemistry at relatively low temperatures. Moreover, this approach has the potential to utilise phosphate-bearing solid wastes as raw materials, further enhancing its environmental benefits. By employing this cutting-edge technique, we aim to revolutionise the phosphorus chemical industry towards greener and more sustainable practices. This paper provides evidence of the feasibility and effectiveness of our proposed approach.

Aug 21, 2024

Outsourcing of mining operations and services is done for various reasons and there is no single model which fits all situations. Experienced contractors and mine owners have also developed, more often than not, jointly, numerous commercial arrangements and project delivery methods to suit their particular project. It is often the case that some mine owners who have not considered outsourcing to contractors do so because of a simple lack of understanding of the potential benefits. This paper will highlight the potential benefits and perceived disadvantages of outsourcing for mine owners and demonstrate how these issues have been addressed by the mining contracting community over recent times as well as demonstrate the evolution of current commercial arrangements in engaging mining contractors.

Jan 1, 2006

By J Emslie

Newmont AustraliaÆs Callie Underground Gold Mine is located on the Dead Bullock Soak Mining Lease, approximately 600 km NW of Alice Springs, NT, in the Granites-Tanami Goldfield. Dead Bullock Soak is part of NewmontÆs Tanami Operations, which also include the Granites Gold Mine and processing plant, Groundrush Open Pit and Tanami Mill. Callie is a world class Proterozoic gold deposit; production to date is in excess of 1.7 million ounces, with an additional Proved and Probable reserves at the end of 2002 of 10.8 Mt at 6.3 g/t. Gold mineralisation at Callie occurs in thin (1 - 30 mm) steeply dipping quartz-chlorite sheeted vein system that cuts across a 40¦ plunging folded sequence of medium to fine-grained metasediments. While the vein system is highly continuous, the gold distribution is highly variable and is controlled by the interaction of lithology, alteration, structure and vein density. The mineralisation is commonly coarse-grained and has a relatively high nugget effect, consequently the orebody is problematic to estimate and shows a high degree of sensitivity to drill hole density. Resource modelling at Callie is an example of a geologically driven model that has evolved with increasing data and understanding. Lithological and structural models are employed to define domains within which the grade estimation is undertaken using multiple indicator kriging. This gradual model evolution impacted greatly on the selection of the mining method. Uncertainty in the estimation of the orebody was a significant factor that led to sublevel open stoping with cemented aggregate fill being adopted as the mining method to improve extraction selectivity. Callie often shows strong positive reconciliation compared to the mill. The mine geologistÆs face the challenge of limiting the degree of underestimation of the core of stopes whilst ensuring that stope boundaries are not conservative. This can only be achieved through the mapping of subtle geological features in order to confirm the orebody model. The increased use of the geological mapping has improved our understanding of the controls on mineralisation and has been extended into the development of new models for near mine underground exploration.

Jan 1, 2003

From 1980 to February 1991 the Rosebery concentrator purchased ore from Aberfoyle's Que River Mine. Following the termination of the contract the concentrator reverted to treating Rosebery ore alone. Since that time it has become apparent that the circuit configuration employed was no longer optimum for zinc metallurgy. The circuit was designed to treat a difficult, slow floating sphalerite; however, the opposite was now found to be true. The sphalerite is fast floating and the circuit was cumbersome. During 1992 extensive circuit changes led to the provision of a simple open circuit flow sheet. The circuit is now easier for operators to understand and lends itself to improvements in process control. Middlings streams have been minimised, which produces a far more stable circuit. Significantly, it must be noted that the key to achieving potential results must lie in reducing variations within the process. A significant ore characterisation program has been undertaken, providing an insight into the metallurgical compatability of the ore to be mined. Using the information collected in this program, metallurgical recoveries and grades can now be predicted with a geater accuracy. Ore characterisation data suggests that an improvement from a 54 per cent zinc concentrate to a 57 per cent zinc concentrate should be achievable. By understanding the size-by-size mineral assemblage, a strategy for concentrate grade improvement has been developed. The requirements of the customer must in all cases determine the quality of the product. Pasminco is a fully-integrated zinc producer and as such significant gains can result by tailoring the concentrates to suit the Smelters.

Jan 1, 1993

After a very brief historical survey and overall assessment of traffic requirements, the invitation by the British and French Governments for private groups to make proposals for a "fixed link" is described, and the resulting plethora of proposals is reviewed. The three schemes which gave some promise of being adequately backed by private finance are described as follows:

Jan 1, 1987

By M J. Nugus, S C. Dominy

Mesothermal lode-gold deposits often pose problems during sampling because of their complex and erratic gold grade distribution, and the presence of coarse gold. Effective sampling and sample preparation protocols must form the basis of any resource estimate at whatever stage a project is at. Design of a sampling regime must be based upon a thorough understanding of orebody mineralogy and geology. This should include consideration of gold particle size and distribution. The sample type, size and density employed must also be based on the underlying geology of the deposit. Choice of sample preparation procedure and assay type is of critical importance if fundamental sampling error and analytical errors are to be minimised. Traditional fire assays, using small charge sizes, consistently understate assays gained from large charge sizes and techniques such as screen fire assay and bulk leach extractable gold assay. The proportion of coarse gold within samples will have a profound effect on the requirements for sample preparation and assay method. The application of Gy sampling theory can help to reduce errors within the processing of samples of broken rock. Quality control/assurance of sampling regimes must also be critically assessed. The problems associated with sampling mesothermal lode-gold type deposits are presented as case studies from Western Australia and North America.

Jan 1, 2003

This paper examines the methods and people required for the evaluation of project or corporate acquisitions. Experience over the past five years has shown that some growth can be achieved by carefully evaluated acquisition of gold projects within regions where the acquiring company has gold processing facilities. Many Western Australian companies have participated in this process and the trend seems likely to continue with a diminishing number of larger producing companies controlling through joint venture or direct purchase of widely spaced ore deposits. In some cases the acquisition may include ore processing facilities, however an increasing number of smaller project acquisitions, involving small open pit gold deposits, which are within trucking distance of the acquiring company's mill. Whilst gold prices remain at the current depressed level we can expect to see this trend continue.

Jan 1, 1989

By Weir D. R, Doyle B. N

The Sherritt Zinc Pressure Leaching Process is based upon the direct pressure leaching of zinc sulphide or lead-zinc bulk sulphide concentrates to produce zinc sulphate in solution and elemental sulphur in the leach residues. The zinc sulphate solution is compatible with conventional purification and electrowinning technology. The pressure leach residues can be treated for the recovery of elemental sulphur, lead and silver. With the conversion of sulphur to the elemental form, zinc pressure leaching allows zinc winning to be independent of sulphuric acid production. Direct pressure leaching of zinc sulphide concentrates was started commercially in October 1980. Continuing research and development studies have defined various pressure leaching configurations for integration with existing roast-leach operations, for grass roots plants, or for plants which are to have the roast-leach section completely replaced. These studies have included the treatment of zinc concentrates from various Australian producers and the development of process flowsheets for potential applications in Australia.

Jan 1, 1989