Search Documents

In common with general experience in the iron-making industry overseas, Australia has in recent years suffered a deterioration in the physical quality of her iron ores in their suitability as a direct blast furnace feed. The increasing amounts of fines and the more friable nature of lump ore, especially in the ore from the Cockatoo Island deposits in Yampi Sound, Western Australia, have focused attention on problems of ore preparation and agglomeration, particularly sintering.Although very small pilot scale Dwight-Lloyd type sinter machines were operated at the steel-making centres at Newcastle and Port Kembla during World War II, no sizeable capacity was installed, so that ore was charged to the blast furnaces almost entirely unscreened, and the resultant flue dust was stockpiled.Towards the close of the war, the pilot plant at Newcastle was replaced by a small machine, adjacent to the flue dust stockpile, with a rated capacity of some 20 tons per hour. After approximately five months of part-time operation, this plant was closed down in January, 1945. Production was not resumed until December, 1950, when, due to a temporary ore shortage, it was decided to supplement available ore with sinter produced from the large flue dust stocks of about 300,000 tons. In spite of mechanical and process difficulties, inherent to the design of the plant, operation was continued on a two-shift basis, with several shutdowns for extensive overhaul and plant alterations, until September, 1954, when production was put on a three-shift basis. Addition of Yampi ore fines to the sinter machine burden was not commenced...

Jan 1, 1957

Comparing Energy Efficiency of Multi-Pass High Pressure Grinding Roll (HPGR) Circuits With increased emphasis on reducing costs and carbon emissions in mineral processing, it is becoming essential to employ the most efficient comminution devices and to use them to maximum effect. High pressure grinding rolls (HPGR) are considered highly efficient compared with other devices, however their relative efficiency in multi-HPGR circuits is less well understood. A series of comminution tests was carried out to evaluate three multi-pass HPGR circuits and a jaw crusher-ball mill circuit. Combinations of HPGR units (1.0 m and 0.25 m diameter), jaw crushers and Bond ball mills were used to grind a 32 mm top size porphyry copper feed (BBWI = 12.1) to a product P80 size of about 150 ¦m. Up to three passes of HPGR were used in each circuit, with energy measurement and size analysis at each point in the comminution process. The energy efficiencies of individual comminution stages and of the overall circuits were quantified and evaluated using three different approaches. The operating work index method for comparing comminution energy efficiency underestimated HPGR performance due to the large amount of fines generated. The -75 ¦m efficiency factor and F50/P50 reduction ratio interpolation methods both give a fairer measure because they better take into account the amount of fines generated by HPGR. The results show that the relative comminution efficiencies of the three multi-pass HPGR circuits tested differ by as much as 22%, providing insights as how to best employ HPGR in a comminution circuit. The most energy efficient of the circuits tested was a three-pass HPGR circuit with a 1.0 m diameter roll on the first pass in closed circuit with an 8 mm screen followed by a second and third pass in a 0.25 m roll.

Sep 13, 2010

Mining education has received almost continuous discussion since its inception and most people engaged in the mining industry and in mining education feel at some time the urge and necessity to express their views. This paper is not a comprehensive survey of past and present practices and accepted principles, but a personal opinion of the form mining education should take at university level. It is expressed because of a dissatisfaction with the existing courses offered to students. It is hoped to provoke discussionand bring forth guidance to those engaged in mining education. After all, students spend four or five years at a university and it is desirable that the graduate should be something more than just those many years older at the end of his course.POST GRADUATE EMPLOYMENTThe first problem confronting the university should, be to discover what the mining industry wants and expects or graduates. This must influence the university course and yet universities have done little to seek this information, and if suggestions have been offered by industry; universities appear to have made little use of them. University mining curricula are basically what they were 50, 100 and even 200 years ago. (See Appendix.) Whether this reflects the unchanging problems of mining the wisdom of early professors, the conservatism of subsequent professors or inability to apprectate necessity for changes, is debatable.Unfortunately there is no uniformity in the type of employment offered to new graduates: Some mining...

Jan 1, 1959

Influence of Frothers on Bubble Shape and Velocity Close to the Generation Point

Sep 13, 2010

By B McCreath

Industrial process water for the Commodore Coal Mine and the adjoining Millmerran Power Station is provided by pumping secondary treated sewage effluent 100 km from the Wetalla Sewage Treatment Plant near Toowoomba. (A separate source is used for potable water.) The effluent is not of sufficient quality for discharge to a watercourse, but it is suitable, with further treatment, for the mine and power station. In designing and constructing the pipeline, special emphasis was placed on preventing accidental spills or planned releases to the environment. The pipeline and associated works can transfer 1000 ML/annum for reuse in the coal mine and power station.

Jan 1, 2003

Fines and unnecessarily small rock fragments are created by as many as four identifiable breakage mechanisms which operate close to the charged section or sections of the blasthole. The peak blasthole pressure (Pb) should not exceed that value at which the rock starts to fail in compression. Excessive Pb values can be prevented by carefully selecting:1. the composition, density and/or diameter of the charge, and2. the initiation/priming system.The percentage of fines increases with:1. increases in the charge diameter:blasthole diameter ratio, burden distance, blasthole diameter, effective sub-drilling and size of blast, and2. decreases in blasthole spacing, stemming height and the length:width ratio of the blast block.Decked charges tend to reduce the percentage of fines.Excessive fragmentation is more evident in buffer blasting and sinking cut shots than in blasts fired to a clean free face. Initiation sequences which give effective burdens considerably less than drilled burdens encourage the minimization of fines, as does an inter-row delay time which promotes good progressive relief of burden.The wastage of explosive energy in creating fines is most pronounced where fully-coupled, energetic charges are fired in weak and/or highly porous rocks. This is especially so where forward movement of the strata is impeded by buffer rock, excessive burden distances and/or inadequate inter-row delay times.

Jan 1, 1979

Interest in those physical properties of minerals which might be used to good effect in prospecting is not new. Early in the nineteenth century attempts were made in th'e Cornish mines to measure the natural electric potentials set up by chemical changes proceeding in the lodes. The distortion of the earth's magnetic field by bodies of strongly magnetic iron ore received early recognition in Sweden. Treasure-finders, working on the principle of electrical induction, appear to have been invented about eighty years ago, though were probably not then applied to mineral exploration. By the end of the nineteenth century Eotvos, a Hungarian physicist, had constructed a highly sensitive type of torsion balance capable of measuring the minute distortions in the earth's field of gravitation resulting from variations in the density of the materials composing the crust. During the first decade of this century he demonstrated its value in tracing rock-salt deposits in virtue of their low density compared with the surrounding rocks. Geophysical prospecting began to be recognised as having a very definite value and its development gathered momentum. Its great expansion took place after the 1914-18 war, when its value in oil exploration was amply demonstrated, and this expansion has continued to the present time and shows no signs of abating.Divisions of Applied Geophysics.The four main divisions of applied geophysics are electrical, magnetic gravitational and seismic. With the importance of ores of radio-active metals, one might add to these a radio-active division. The first two are more important to the field of mining, but techniques based on gravitational attraction have their uses in particular cases. Seismic methods are not generally suited to the exploration of metallic ores, but have proved of enormous value in the search for petroleum. With vast quantities of oil as the prize, more money has been lavished on the deve10pment and practice of these methods than on all the others put together.Geophysical Prospecting Methods.Geophysical prospecting methods may be used to detect a mineral deposit directly in virtue of differences in the intensity of some physical attribute common to it and the enclosing country rock. Examples of this are the detection of rock-salt by gravity measurements, or of iron ore by magnetic methods. Of much wider application, however, is the indireot approach in which the aim is to determine, by geophysical means, the geological structures controlling the disposition of mineral deposits. These structures may be partly known from geological work, in which case geophysical methods are useful adjuncts. Where, because of an 'unbroken cover of overburden, no useful geological information presents itself, scout drilling or geophysical prospecting are the only alternatives. Overburden is here intended to mean any covering material not, involved in the structures controlling the mineral deposits. Prospecting for petroleum amounts to the detecting of favourable reservoir structures, and as the chief types of such are the same the world over...

Jan 1, 1950

Improving Pelletisation of Pyrite Cinder by High Pressure Roller Grinding As an important secondary resource for ironmaking, pyrite cinder is characterised by coarse particle size, low specific surface area, high porosity and poor surface activity, which leads to high bentonite dosage, low strength and too high moisture of green balls and high roasting temperature. In this paper, a study of improving the pelletisation of pyrite cinder containing feed by using high pressure roll grinding (HPRG) was presented, which aimed to improve the quality of green pellets and reinforce roasting performance pellets. It is shown that pyrite cinder is characterised by complicated mineral compositions dominated by haematite and metal sulfides, porous surface and middle class ballability, leading to higher balling moisture, higher bentonite dosage and higher firing temperature for pellet hardening. The pelletisation of pyrite cinder can be improved by high pressure roller grinding and blending with magnetite in the pellet feed. The former is probably ascribed to the increase in specific surface areas of pellet feed from 850 cm2+g to 1690 cm2+g when the pellet feed passes through roller twice. Good quality green balls and fired pellets can be made from feed comprising 40 - 60 per cent pyrite cinder and 60 - 40 per cent magnetite concentrate at small scale under the following conditions: 1.2 per cent bentonite, feed passing through roller twice at 7 per cent moisture at 1.5 ton pressure, balling at 13 per cent moisture for 13 min, preheating at 1050¦C for 12 min and firing at 1300¦C for 8 min. Green balls possess such properties as drop numbers of 6.5 times, compressive strength of 19.1 Newton and thermal shock temperature of 533¦C. Fired pellets are imparted high compressive strength of over 3000 Newton per pellet. Small scale tests have been proven by pilot scale tests that high grade fired pellets are made, assaying 63 per cent Fe and minor other impurities, such as sulfur and phosphorus except for copper content. The fired pellets made of three blends possess excellent metallurgical performance, such as reducibility index higher than 65 per cent, reduction swelling index lower than 15 per cent and low temperature reduction degradation lower than2 per cent. Especially the compressive strength after reduction is higher 719Newton per pellet.

Sep 13, 2010

The Kingsgate molybdenite pipes are considered on petrochemical data and field occurrence to be, possibly, epi-magmatic plutonic offshoots grading into hydrothermal bodies. There is reason to believe that the ore is derived from a highly acid granite of type similar to that of the tin bearing areas of northern New England. The mineralogy, microtextures and paragenesis of the ore are discussed.INTRODUCTIONThe Kingsgate Mining Field is situated in steep, heavily timbered terrain 18 miles E.N.E. of Glen Innes and 430 miles north of Sydney. Bismuth and molybdenum ores were discovered at Kingsgate (Yarrow Creek) in 1877. Subsequently some 50 pipes were developed yielding tonnages which at the peak of operations, 1905 to 1920, rivalled production from the rich deposits of northern Queensland.Attempts to revive the field have been made periodically and small parcels of ore have been forthcoming.' During World War II demand for piezioelectric quartz again focussed attention on Kingsgate but twinning and other imperfections of the quartz prevented all but a minor exploitation of the otherwise noteworthy crystals of this locality.There is reason to believe that the ore at Kingsgate is not exhausted through exploration and mining costs would probably be high due to the capricious nature of the pipes and to the irregular distribution of rich ore shoots within them.

Jan 1, 1962

Calculations of the temperatures of metal, coke, and gas at any level in the cupola furn~ce can be carried out by means of heat balances, using data obtained from experiments with an 18 in. experimental cupola. The results can, to a certain extent, be verified by means of heat transfer calculations.The curves thus obtained, showing the variation of temperature with height in the cupola, provide a valuable picture of the heat transfer processes in a shaft 'furnace.INTRODUCTIONThe Brown Coal Research Laboratory, of the University of Melbourne, has been engaged in recent years on a programme of iron-melting tests in an experimental cupola furnace.Although the ultimate aim of this work is to develop brown coal char as a cupola fuel, most of the experimental work so far has been with conventional coke. The testing programme was designed to provide information on the effect of variables such as blast rate, metal-coke ratio, and coke size on the overall melting process, e.g. melting rate, temperature of metal tapped, and stack gas composition.However, in many cases data were obtained on conditions inside the furnace by measuring temperatures and gas compositions. The aim of the work described in this paper was to qevelop a method for using this data to obtain information on the processes taking place in the cupola.Very little research has been done on the combustion of fuels in shaft furnaces. Early work on this subject, as well as the initial stages of the Brown Coal Research Laboratory's programme, has been discussed by Evans (1959). The use of probes for obtaining information on conditions in the interior of a shaft furnace was pioneered by Belden (1913)...

Jan 1, 1963

ABSTRACTMechanised cut and fill stoping in the Racecourse orebodies between II and 9 levels was started in 1964.Five stopes are in progress over the two level interval, extracting the full strike length (600-2,000 ft) of each orebody without transverse pillars.Each stope is served by a central 10 ft by 12 ft service intake ventilation raise and an 8 ft by 8 ft return air raise at each end of the stope. Each stope is divided into two sections for drilling. firing. mucking, and fillingto maintain steady production. All equipment is kept in the stope for one level lift stoping. Gardner-Denver 2 boom jumbos are used for uphole drilling and Wagner ST 5 Scooptrams for loading and transport to ore passes located in the footwall of the orebody. A Wagner PTIO is used for materials handling and scaling of the stope backs.Mill tailings, after one stage of cycloning are used to fill the stope, one section at a time. About 80 per cent of the water is removed by decantation while the remainder percolates through hessian-covered pipes and boxes.The ore is passed to 11 level where it is hauled by the 3 ft 6 in. gauge train to the tipple at the shaft area. The ore is crushed underground before hoisting to the surface.A performance of about 100 ton/manshift is achieved by the drilling, blasting, and mucking crews in the stopes.

Jan 1, 1968

IN the construction of a set of ordinary mine plans, two axes or coordinates are used; also, two different projections are essential viz., a plan (horizontal projection) and longitudinal section (vertical projection). In isometric projection three axes are employed-one axis vertical and the remaining two inclined to it at angles of 120°, also making an angle of 120° with one another, as shown in Fig. 1. The two inclined axes are used to plot the horizontal projection, while altitudes are plotted on the vertical axis. As an illustration, consider the ease of a simple object, such as a box. To show all the dimensions in the usual manner requires two drawings-a plan and elevation, as in Fig 2.

Jan 1, 1919

Very few of those occupied in pursuits other than mining have any conception of the extent of boring operations that have been carried out on the gold and coal fields of Victoria, or of the valuable and definite knowledge obtainable by such means. The subject comprises various branches, which it will be necessary to describe in detail. The three main divisions are The Administrative, which includes all financial work and general management. The Professional, dealing with topographical and geological work necessary before any scheme of boring can be laid out, the preparation of plans, the inspection of cores obtained from bore holes, the examination of diamonds, etc. The Mechanical Branch, dealing with the drilling machinery, setting of diamonds, maintenance of stores, etc. In 1877, the Goverpment of Victoria decided to assist in prospecting the mineral resources of the colony by the aid of diamond drill boring, and for that purpose, a vote of £5,000 was passed, with which were purchased three diamond dulls, an American type being adopted.

Jan 1, 1901

Alluvial mining even of shallow deposits is often economically a marginal proposition and causes significant disruption of the land surface through the need for large scale excavation. In-situ leaching using chlorine-based solutions eliminates the need for excavation, the disruption of surface activities, and may greatly reduce processing costs and improve recovery especially of fine gold. A spreadsheet model has been developed to design and analyse the economics of in-situ leaching of alluvial deposits. In-situ leaching of shallow deposits may be achieved in a number of ways including solution infiltration via perimeter ditches or the use of injection and production wells. In most instances deeper alluvials may only be processed using well systems. Two deposits are analysed in this paper. The first consists of one metre of payable wash beneath one metre of overburden. Some thirty fields per year are treated processing 450 000 BCM per year at a cut-off grade of around $4/tonne ($8/rn3 or the gold value equivalent of 0.26 gh or 0.52 g/m3). The principal costs are well drilling and labour. Sensitivity analysis indicates that doubling the throughput halves the cost. The economics of the project are relatively insensitive to reagent costs and consumptions, and halving the recovery doubles the cut-off grade. Shallow deposits treated using the infiltration ditch system may be marginally cheaper and more conveniently managed although this depends on the relative cost of digging the perimeter ditches. In a second example, deep leads with one metre of wash beneath 30 metres of overburden necessitate significant drilling and feature reduced throughputs as a consequence. In the example chosen 30 fields a year are processed for an annual throughput of 65 000 tonnes costed at around $20/tonne (1.4 g/t Au equivalent, $40 /m3). Sensitivity analysis indicates that throughput, and drilling cost per metre are not important but there is a high sensitivity to recovery and to the depth to payable wash.

Jan 1, 1992

A study of the electrolysis of PbS in molten PbCl2 showed cathode efficiencies which increased with current density at fixed sulphide concentrations, and decreased with increasing sulphide concentration at fixed current densities. The anodically produced sulphur dissolved rapidly in the melt, the rate increasing with temperature and sulphide concentration. Experiments with diaphragm cells, made to determine the relative effects that dissolution of lead and sulphur have on the cathodic current efficiency, demonstrated that dissolution of sulphur was the major contributor to the lowering in efficiency.

Jan 1, 1973

By A Watson

We tend to overestimate the volume of water used to process ore and the evaporation from tailings and heap leach stockpiles. During mine operation, a significant portion of the water collected from onsite water management systems is consumed and recycled by ore processing and lesser portion discharged to the environment. When mining and processing cease, however, the mine site water balance is altered and the real effort and cost associated with managing and disposing of excess mine-influenced water becomes evident. As these flows can no longer be recycled and may not be suitable for discharge to the environment, the cost of dealing with them can comprise a significant portion of the post-mining liability. The problem of dealing with large volumes of mine affected water has the potential to become worse in the future due to the established trend of lower grades which require more water per unit of mineral processing. As a result, future mines may be expected to have greater water needs and problems than we experience today.This paper discusses various aspects about how water usage changes when a mine transitions from operation to closure based on observations and numerical simulations of made with site-wide water balance models. The intention is to provide general considerations for mine operations in planning for end of mine life and post-mining care and maintenance.

Jan 1, 2009

By S Jackson, I Arbuthnot

The use of High Rate Thickeners has gained wide acceptance in the mineral treatment industries. The design of these units is characterized by an efficient deaeration and flocculation chamber, and introduction of the flocculated feed solids into a preformed floc bed zone. By these means the settling process is accelerated and consequently High Rate Thickeners achieve a significantly higher throughput per unit area than conventional thickeners.   The object of a control system on a High Rate Thickener (HRT), as on a conventional thickener, is to obtain the required underflow density and overflow clarity at all feed conditions. The feed conditions which may vary include volumetric and mass feed rate, pulp density, particle size and particle type. A conventional thickener has a large volume and cross sectional area, and changes in performance occur slowly û the operator has time to observe and react to these changes to maintain control. On a HRT, there is a much reduced residence time and therefore control parameters need to be reset more frequently. Although manual control is possible, the use of automatic control systems is therefore desirable to avoid excessive operator attention, while optimizing control of density and clarity. Automatic control of a conventional thickener is usually achieved by an underflow density loop which regulates the rate of withdrawal of underflow. A turbidity meter is sometimes used to measure overflow clarity and regulate the addition of a coagulant or polymer flocculant. These measures are not adequate on a HRT, because they would not give optimum control and could lead to excessive flocculant use. To achieve optimum operation in a HRT, the floc bed level should be maintained above the feed inlet point in the thickener. This bed level has become the key variable around which most control systems have been designed. However, a number of problems have occurred which has resulted in poor control, or only partial control of thickener performance. We will describe some of these problems, and a solution which is simple and effective.

Jan 1, 1990

Situated in the Greymouth Coalfield, the Mt Davy Block contains a significant resource of high quality bituminous coal suitable for use in metallurgical coking coal blends. The coal, which is all low sulphur, is seen as a complementary deposit to export coking coal at Stockton Mine.   Previous drilling by State Coal Mines (1948 - 1953) and Japanese interests (1970's) have been supplemented by Coal New Zealand drilling (1992 - 1993) and surface mapping. A mining feasibility study was completed in late 1993 and approval gained for the driveage of an exploratory tunnel to the target seam.   Following construction of surface facilities, tunnel driveage on a 1:5 decline commenced from Rewanui in May 1995 and to date about half the required length has been driven. When the seam is intersected a comprehensive geotechnical testing programme will be undertaken to assess the in-situ mining conditions. It is expected that the results will confirm the assumptions made in the feasibility study.   The Mt Davy Mine, at depths of 500 - 700 metres, will be the deepest underground coal mine ever inNew Zealand and in-situ stresses (orientation and magnitude) will be important considerations for mining engineering. The coal has a high gas content and suitable techniques for gas control and prevention/mitigation of coal outbursts will be necessary.   Mine development is scheduled to commence in mid 1998 and an annual production level of 500 000 tonnes is forecast. The coal seams will be developed by continuous miner and coal extraction will be by hydraulic monitor. Coal will be pumped to the surface and from Rewanui transported five kilometres to Dunollie either by truck or slurry pipeline. At Dunollie a coal dewatering plant, coal stockpile and rail loadout will be constructed.

Jan 1, 1996

In 1976 the Pitjantjatjara Council was established under the Associations Incorporation Act 1985 (SA), for the initial purpose of organising and bringing together three similar Indigenous groups. These members of the Pitjantjatjara Council of Central Australia were demanding land rights and to legally protect their traditional lands. The Land Rights movement was more focused on the South Australian Government that became more receptive to the general notion that Aboriginal freehold land could be attainable.For almost five years, Pitjantjatjara CouncilÆs intense negotiations took place with the Dunstan and Tonkin Governments culminating in the final passage of legislation by 1981. A bi-partisan approach by Government and opposition applauded by all South Australians for its mature and socially responsible actions, in line with the Aboriginal Land Rights (Northern Territory) Act 1976 (Cth). Despite the similarities between South Australian and the Northern Territory Land Rights legislation, there still remains one obvious distinction. In the Northern Territory case, its legislation established æLand CouncilsÆ as statutory authorities that are responsible for the management and use of designated Aboriginal lands. On the other hand, South Australian legislation fails to include any reference to æLand CouncilsÆ as defined in the Northern Territory Act. The intention of establishing such æLand CouncilsÆ in the Northern Territory was, and is to provide legal, anthropological and other expect advisers that respond to the wishes and opinions of Traditional Aboriginal Owners. Negotiations between mining companies and Land Councils, will, after the granting of mining leases, monies are then transferred to those Councils being a percentage of royalty entitlements. While the Pitjantjatjara Land Rights Act 1981 (SA) (Act) does provide royalty arrangements to Anangu Pitjantjatjara (AP), a body corporate pursuant to the Act as a Landholding Body (and not as a æLand CouncilÆ), it does not provide any royalty payments for the legal and anthropological services by the Pitjantjatjara Council for providing essentially similar services as the Northern Territory Land Councils. The limited services by AP do provide complimentary services from other organisations û including the Pitjantjatjara Council. There are approximately 4000 Anangu members who reside on AP Lands and more than 1000 other Anangu members live near AP Lands in Western Australia and the Northern Territory. These people are defined as APÆs æTraditional OwnersÆ by virtue of their affiliation to portions of AP Lands. As a result, the depth and understanding of spiritual beliefs and customs are strongly present as it relates to the whole of the Lands. Most of these members reside at permanent communities that spread unevenly about the northern and south-western parts of AP Lands. In addition, there are numerous æHomelandsÆ where families and extended families have establish homes, with electricity and water supplies on those Traditional Lands (see Appendix 1 and 2 of this paper depicting the map showing AP Lands and also showing stunning photographs taken during late last year). All roads and airstrips are unsealed between communities and Homelands and the essential services to all communities are limited and costly to provide, and require continuous upgrading. Capital expenditure on infrastructure is sorely needed and alarming levels of unemployment is of serious concern. Tjilpi (older) Anangu members have continually discuss the urgency to provide employment and education for the future of their children and grandchildren while balancing the needs of maintaining cultural and spiritual considerations. It is thus a growing realisation by many Traditional Owners that long-term benefits occur as a result of exploration and production of oil or minerals. There are promising results from Primary Industry and Resources of South AustraliaÆs (PIRSA) Aero-magnetic Surveys on the Musgrave and Mann Ranges and soon to be completed surveys of the remaining southern half of AP Lands (see Appendix 3). PIRSA and mining companies û such as Rio Tinto Exploration Pty Ltd and Delta Gold NL û have been more conscious of the necessity for improving the dissemination of information to Traditional Owners and to AP members. With recent findings of large nickel deposits just over the border in Western Australia, there is a strong indication that discoveries may occur on AP Lands as similar geological information is present on the east Musgrave Block. Consequently there are concerted efforts by the legal and anthropological services of the Pitjantjatjara Council to arrange Workshops and Summit meeting to give extra information û particularly information concerning the true effect of large-scale mining operations û to members to properly consider these proposals. Pitjantjatjara Council will play a major role in any decisions effecting Traditional Owners and AP, and will ensure orderly and professional services when dealing with legal, cultural and sensitive matters. This paper addresses the historical and current relationship between Pitjantjatjara Council and AP, with an emphasis on mining operations on AP Lands. It argues that future economic and social development on AP Lands hinge predominantly on the legal recognition of the Pitjantjatjara Council for its ongoing role, responsibilities and protection afforded to AP and its Traditional Owners.

Jan 1, 2002

Fragmentation Characteristics of Iron Ores from Anshan, China

Sep 13, 2010