Search Documents

A zone rich in-fish debris in the Rolling Dow= Group in the sub-surface of the Great-Artesian Basin has been discovered a Further research has shoe i this zone to-be of very wide distribution in the Artesian Basin and to occur. at the base of the Ta?nbo .f ormati'on resting on the Roma forma-tion. The zone gives a very characteristic curve on the electric and' gamma ray logs and is thus an excellent correlation marker in the sub-surface over a very wide area. It is probably to be correlated sith.the Toolebuc member described from: outcrops east of Boulia. There .are apparent similarities between the Fishecale zone of the Great Artesian Basin in' Australia and the Fishscale sand of the Western Canada Sedimentary Basin.

Jan 1, 1962

The Auscoke project has reached-a stage where a pilot plant nominally able to produce 100 t.p.d. of coked briquettes is being brought on stream during Nov. 1971 . The targets for this stage of the project are to establish the technological and economic value of Auscoke for the iron blast furnace, and to verify the commercial feasibility of large scale plants. The project originated at the B.H.P. Central Research Laboratories (C.R.L.) and work to date has shown that using a two stage contin- uous process, strong large coke can be produced at good productivities from medium or low volatile poorly caking coals. General features of the pilot plant and processing are discussed.

Jan 1, 1972

By D B, M A. Sares, D W. Coulter, D C. Peters

This presentation discusses NASA-funded research on the ability of hyperspectral remote sensing to map diagnostic acid rock drainage (ARD) mineralogy that adversely affects water quality within watershed and to determine the relative contributions of natural ARD sources of metals and acidity to that drainage. Ground-based reflectance spectroscopy, combined with water chemistry, is used to identify mineralogical and chemical variations throughout a watershed. Integrated with hyperspectral data acquired from airborne remote sensing platforms, such as the NASA Airborne Visible Infrared Imaging Spectrometer (AVIRIS) sensor, a methodology has been developed that should improve environmental assessments and tracking of impacts on and from drainages. Phase I of this project focuses on a drainage basin (Lake Creek), tributary to the upper Arkansas River in central Colorado, which is impacted by natural acid rock drainage from areas of high-sulfide hydrothermal alteration. This project builds upon research and inventory efforts by the Colorado Geological Survey (CGS) to identify hydrothermal alteration that is the primary source or is contributing to acidic and toxic drainage in Colorado. This presentation will cover ground and airborne hyperspectral remote sensing techniques and results and water analyses for seasonal high-flow and low-flow conditions in Lake Creek. Identifying correlations between mineralogy, especially mineralogy that can be identified through airborne remote sensing, and water chemistry is a key focus of this project. Of particular interest are low-pH iron phases such as jarosite, ferrihydrite, schwertmannite, copiapite, and transitional amorphous phases as well as AlOH phases from higher, although still acidic, pH environments which are observed to mix with the iron precipitates within the streams draining from the hydrothermal systems. Drainage in the Lake Creek watershed derives from the Grizzly Peak caldera (Oligocene), which exhibits extensive hydrothermal alteration. Alteration types include silicic, quartz-sericite, quartz-sericite-pyrite, advanced argillic, and argillic. By understanding the chemistry of a naturally impacted drainage and its relationship to the surrounding geology, the project goal is to allow more efficient and complete identification of such sources in mineralised terranes through remote sensing technology.

Jan 1, 2003

By Fair A, Oxenford J

Syncrude Canada Ltd operates one of the largest open pit mines in the world at Fort McMurray in northern Alberta, Canada. In 1993, Syncrude mined and processed 131.2 Mt of oil sands to produce 67.0 MBbls of synthetic crude oil (SCO). This represents approximately 13 per cent of Canada's crude oil requirements. In addition to the oil sand mined, Syncrude moved approximately 96 Mt of overburden ahead of the mining operation in 1993. Since start-up in 1978, Syncrude has had outstanding success in improving the safety and reliability of its operation. Much of this success has been achieved by reducing risk through the application of new and improved technology. This improved safety and reliability has resulted in, among other things, very significant improvements in operating costs and profitability. This paper discusses some of the technology applications that have been introduced at Syncrude to reduce risks to people, equipment, operations and the environment. Three specific examples will be discussed in detail to demonstrate how reductions in risk have greatly improved the operation.

Jan 1, 1994

By D Fargher

BHP BillitonÆs Cannington operation began production in 1997 and is presently the largest tonnage and lowest cost single mine producer of both lead and silver in the world. The original design capacity was 1.5 Mtpa and this has progressively increased via a series of debottlenecking projects in both the mining and milling operations. In 2003, 2.39 Mt of ore was mined, whilst 2.31 Mt of ore was milled. In February 2003 Cannington received approval to expand the project to a sustainable capacity of 2.4 Mtpa. This resulted in underground development into the northern zone, upgrades to the concentrator, increased accommodation at site and power station capacity. The Cannington project development team implemented a partnership approach to the project. Fraser Osborn Engineering and Outokumpu Technology worked closely together with the Cannington team to meet all of the project constraints.

Jan 1, 2004

By Richardson G. W, Yap L. C

Friction rock stabilisers (FRS) are the most common steel-based ground reinforcement used in underground mines in Western Australia. As with any other steel-based product used in underground mines they are susceptible to corrosion, particularly under aggressive minewater and mineral conditions. Because of their thin-wall tubular construction and large surface area, the potential damage resulting from corrosion is considered to be more severe for this type of reinforcement than for other forms of reinforcement made of solid steel bars. Because of the obvious safety problems which may result from corrosion, both mine operators and regulators have raised concerns regarding the long-term effectiveness of FRS installed in underground mines in Western Australia. Although corrosion has been recognised as an important safety issue, the controls of corrosion in varied underground mining environments has not been well understood. To improve the understanding of the corrosion behaviour of FRS, the Department of Minerals and Energy has initiated a research project focused on the mechanisms and extent of corrosion attacks, and their influence on the effectiveness of the reinforcement. This paper describes the research project and presents the interim results achieved To-date.

Jan 1, 1995

Silica-Kaolin Sand Wet Sizing The Bulgarian deposits of silica-kaolin sand are localised in the eastern part of the Danube plain. After wet separation the raw material yields two products - washed kaolin (different grades) and silica sand (different grades). The water washing technology includes: disintegration; spiral classification; hydrocyclone classification and dewatering of kaolin grades; hydroclassification; sizing using drum screens and dewatering of silica sand grades. Research and development program has started to improve the silica-kaolin sand separation in processing plants. Based on the raw material and tails characterisation data and the preliminary experiments using Derrick Stacksizer screening machines a silica-kaolin sand wet sizing technology was developed. The full-scale pilot flowsheet includes the following units: Derrick Stacksizer equipped with 0.43 mm opening Derrick Urethane Panel; 500 mm Flat bottom Hydrocyclone; Derrick Stacksizer equipped with 0.150 mm opening Derrick Urethane Panel; 100 mm Hydrocyclone and Derrick Dual Motor Linear Motion Machine equipped with 0.064 mm opening Derrick Pyramid Panel. The pilot-test data clearly demonstrate that the new silica-kaolin sand wet sizing technology is suitable for Bulgarian silica-kaolin raw material. There are possibilities to increase the silica sand recovery increasing the production of silica sand grade PK 0.16 and starting the production a new grade PK 0.10.

Sep 13, 2010

THIS paper is not intended to be more than a mere outline of the economic geology of Tasmania. It is desired to present in a condensed form the present state of our knowledge in regard to the distribution of the ore, coal, and oil-shale deposits of Tasmania in time and space.Tasmania is exceptionally well endowed with mineral wealth, particularly in the north-western and western districts. In the enthusiasm resulting from the first discoveries of mineral deposits at a great number of localities in those districts, it became a generally accepted belief that the whole of that portion of Tasmania constituted a continuous metalliferous province. As geological research in these, areas has progressed, however, it has become increasingly clear that ore-deposition has been confined on an economic scale to definite well-defined areas or belts which have a genetic relationship to certain tectonic and petrologic phases of the general geology. These areas or belts have recently been defined by the writer, and...

Jan 1, 1923

By Marton A

The Readymix Group have a Quarry Improvement Program - 'Building in Quality (BIQ) which has many parallels to the ICI Explosives' total quality management - 'Quality Improvement Program' (QIP). Both companies have for some time recognised that the 'do it right first time' principle means less wasted effort and materials, that efficiency breeds profitability and so actively promote the quality culture. To install the principles and generate the culture requires considerable commitment and effort from the top down and invariably spreads to the suppliers and sub-contractors. Understanding the component processes involved with the quarry operation, analysis of those processes and gaining a breakdown of the cost of non conformance then allows the astute quarry operator to make the necessary changes to improve the process to realise profits. This paper outlines the steps in such a process and the profitable outcomes of the commitment to continuous improvement at the Nickol Bay Quarry.

Jan 1, 1994

By Jones BH

Discovery of the Vera-Nancy deposit in late-1995 followed 12 years of active exploration in and around the Pajingo Epithermal System, an andesite hosted veinfield covering an area of 150 square kilometres at the northern end of the Devono-Carboniferous Drummond Basin in North Queensland. Early exploration targeted open-pittable resources in the numerous auriferous veins and it was not until 1994 that exploration focus shifted to drilling to depths below about 100 metres from surface, which resulted in the Vera-Nancy discovery. That deeper drilling process is still at a very early stage of coverage of the epithermal system as a whole and substantial potential exists for additional discoveries.Drill-out of Vera-Nancy has to-date established a gold resource in excess of 1.4 million ounces. Mine development is proceeding via a twin decline system with first stoped production scheduled for August 1997.

Jan 1, 1997

By Sweet I. P

Stratigraphic correlations across the Mur- phy Tectonic Ridge are crucial to regional corr. elations between the Mount Isa and McArthur River areas. Recent work in the Westmoreland and surrounding areas has substantiated the earlier general correlations between the Mount Isa and McArthur River sequences. The Mount Isa and McArthur Groups, and their equivalents, remain prime prospecting targets for major lead-zinc deposits of the Mount Isa and R.Y.C. type. A prospective area for Redbank-type copper mineralization is suggested.

Jan 1, 1974

Although the flotation cell has been under continuous development over the past 80 years, an understanding of the precise roles of a cell in produc- ing the flotation result had evolved slowly. In fact, detailed studies of cell dynamics began only in the 1940s when flotation practice had almost reached the half-century mark. The earliest generalizations related cell capacity to power intensity (hp/vol- ume) (Rose, 1946), and specific operating features such as aeration and power ' consumption to impeller submergence and operating speed (Read, 1933). In the 1950s hydrodynamic characterization of cells through power coefficients and air flow numbers began (Arbiter and Harris, 1961) and has continued to the present, with increasing industrial use of these concepts (Degner, 1982; Degner and Treweek, 1976). Liquid flow measurements in Wemco cells (Degner, 1982) made liquid flow numbers and turnover frequencies available for more complete under- standing of cell dynamics. The present overview of flotation technology is a critique of cell design. The cell process represents the interactions between cell dynam- ics, cell geometry, and ores, with the latter prepared for that interaction through size reduction and reagent treatment. While previous invest- igations of flotation cells have accepted all cell designs uncrit- ically, the present study considers the physical process components that an effective cell must provide, and then compares a limited number of

Jan 1, 1984

The paper describes the development leading to the bucket wheel excavator systems now used in the Latrobe Valley and refers in particular to the new S.E.C.V. dredgers Nos. 14 and 15 which will be employed in the Loy Yang open cut. The design concept and operating possibilities of these dredgers are described in detail with reference to the machine characteristics designed for the operating conditions in the Latrobe Valley. The design is compared with units of similar capacity in open cuts of other countries.

Jan 1, 1982

By Alesse V, Belardi G

A new class of collectors, Mercapto-Benzo-Oxazoles (MBO), exerting selective action on copper sulphides in the presence of Pb, Zn and Fe sulphides (galena, sphalerite and pyrite), has been synthesised in co-operation with Enichem's Donegani Insitute. The collectors have a mixed aliphatic-aromatic structure and contain functional groups which form chelates with copper. Some reagents of this class having hydrocarbon chains of various lengths have been laboratory tested on a complex sulphide ore containing chalcopyrite, galena and sphalerite in pyritic gangue. Comparative flotation tests have permitted selection of the best collector for chalcopyrite, namely Methyl-Mercapto- Benzoxazole (MMBO). Systematic flotation tests have been performed with this reagent, varying collector concentration, grain size of the feed, pH and flotation time. The results obtained show that the synthesised collector is much better than potassium-amylxanthate (KAX) as regards selectivity towards Pb and Zn. Moreover, it is possible to work at natural pH (6-7) and the flotation rate is higher. In fact in the rougher stage with 80 g/t of collector at natural pH, a copper grade of 7.14 per cent was obtained with a recovery of 73.87 per cent, while the grade with KAX did not exceed 2.11 per cent for a recovery of 73.54 per cent. The amount of Pb and Zn reporting in the copper concentrate was eight per cent and ten per cent respectively, while with KAX it was no lower than 24.34 per cent and 22.71 per cent in that order. After two minutes flotation a copper grade of 5.2 per cent with 52 per cent recovery could be attained, against a grade of 2.5 per cent and a recovery of 44 per cent in the case of KAX. The efficiency of this new collector has been ascertained on two samples of complex sulphide ores of diverse mineralogical composition.

Jan 1, 1993

By Caigen Wang, Wending Ma, Xiexin Mi

The urgent need for the control of surface subsidence caused by longwall coal mining in densely populated areas of China has led to a feasibility study on the effectiveness of longwall goaf cemented backfill. The study is focussed on exploring the potential of longwall goaf cemented backfill practice for surface subsidence control. Specific backfill geometry was designed in view of the characteristics of the longwall coal mining system. Laboratory physical simulated tests were carried out with different backfill material properties and pack size. The tests achieved a marked reduction in surface subsidence by the use of goaf cemented backfill. The system has been shown to be effective in laboratory tests, the challenge now is to overcome the engineering problems to put it into practice.

Jan 1, 1998

The Central Extended Orebody is located within the Cracow Goldfield approximately 360 km northwest of Brisbane and approximately 220 km west of Bundaberg. It is an epithermal gold deposit hosted by the Late Carboniferous to Early Permian Camboon Andesite. The lode was mined by open cut methods and produced 170 458 tonnes of ore at 5.62 g/t gold.The geology of the rit is relatively simple, comprising two rock types, trachyandesite and rhyolite which have been sub-divided into several units. The trachyandesite is sub-divided into three rock types: brecciated trachyandesite which is the most widespread, hydraulically fractured trachyandesite hosts the mineralisation and the third sub-unit is chloritised hydraulically fractured trachyandesite and has no associated mineralisation. The mineralisation is confined to quartz veins in hydraulically fractured trachyandesite. Several phases of brecciation and subsequent quartz and quartz/adularia vein injection are evident although not all phases are mineralised. Two rhyolite dykes intrude the trachyandesite one is monolithic, the other is sub-divided into hydraulically fractured rhyolite (barren), silicified rhyolite and auto-brecciated rhyolite.

Jan 1, 1993

By Reifenstein A

ACIRL's petrographers apply microscopic techniques to coal exploration, production, preparation and processing problems and research investigations as well as provide a commercial service for quality control of export coal shipments. This paper describes a number of case studies of applications of petrography to coal industry problems and coal research, including

Jan 1, 1989

By Howlett P. F, Courtley S

A problem with secondary breaking at one of the mines of Pasminco Mining led to a study of new rock breaking technologies. Many of the techniques being developed had emerged from the thrust in the USA for continuous drill=break excavation. Such approaches to rock breaking highlighted the applicability of what would normally be classified as tunnelling techniques, to the secondary breaking sector - and possibly the reverse. As a direct result of the investigations for suitable technologies, Pasminco Mining supported the development of two improved rock breaking methods specifically targeting secondary breaking, one of which could be applied to continuous excavation.

Jan 1, 1993

By Cresswell G. M

The international coal industry is becoming increasingly aware of the economic impact of coal dewatering in terms of plant yield limitations, attainment of product specifications and freight costs. This paper examines the current position of dewatering within coal process plant design and reviews equipment developments over the past decade.

Jan 1, 1993

By Fejes G

An integral part of the Brisbane Suburban Railway Electrification involved the relining, refurbishment and track lowering in the Roma Street, Brunswick Street and Gloucester Street double track tunnels. The design and the construction procedures had to satisfy the Queensland Railways electrification clearance and track standards and the requirements of maintaining track services through the tunnels during work. Refurbishing of the tunnel linings was carried out to extend the life of the tunnels.

Jan 1, 1981