Search Documents

The accuracy with which block estimates are perceived is obtained by calculation of the kriging variance. This is dependent upon the model chosen for the semi-variogram of the deposit. For an extensive series of spherical semi-variograms the changes in the kriging variance resulting from various degrees of misassignment of the relative nugget effect are investigated. The results are reported as contour maps of percentage change in kriging variance as a function of the range and relative nugget effect of the true model.

Jan 1, 1985

At the LKAB, Iron Ore Mine, Kiruna, Sweden a preliminary investigation into the reliability characteristics of a fleet of load-haul-dump machines has shown that the hydraulic system is one of the most critical parts. Therefore, hydraulic system was selected for study and analysis through condition monitoring devices so that failure can be controlled or at least the failure consequences can be minimized.The hydraulic system has two different problems; one is that the contamination level is too high and the other is high temperature during operation. At high temperature, seals and tubes are a problem, because they stiffen due to carbonization, which leads to increasing leakage. The pumps and restrictions were responsible for the main temperature increase.

Jan 1, 1991

The mineral resource that a mining company has access to, represents the majority of the embedded value that exists within the company, as well as the competitive advantage that the company has over its peers. However, the real value is only realised once effective mining plans have been put in place, which optimise the extraction of the resource, and add measurable value to the company. The concept of mineral resource management (MRM) has been developed in South Africa, to ensure this optimisation happens in an integrated and quantifiable manner, such that value is added and risk is reduced, resulting in bottom line improvement for the stakeholders of the business. This paper describes the process of mineral resource management, and draws on successes and failures of various companies, to illustrate how it should be implemented, and what measures should be put in place to ensure its success. This requires a fundamental re-appraisal of the way in which mining companies plan and execute their businesses, and focuses attention on real value adding activities and behaviour through the use of economic value added as an appropriate metric by which to measure real value and risk. Specifically, the paper focuses on these aspects as applied to planning models and processes, exploration activity and risk management, to ensure operational and project success.

Jan 1, 2006

By Seeley D, Buckley N, Goodall J

Improving the performance and reducing the costs associated with export logistics chains is critical to the competitiveness of export coal mines. The fundamental practices associated with the use of export logistics chains made up of mine, trucking, rail and port operations are being challenged by the advent of third party operators on rail systems and the use of the Internet.Whilst individual mines can improve their processes to drive down their mining costs, they face major challenges in their endeavour to improve the performance of export logistics chains and reduce the significant logistics costs of moving coal from the mine to export ships, via the shared infrastructure of rail systems and ports. There is an increasing realisation that global competition is not only between mines but between coal export regions that are defined by their rail system and ports infrastructure.

Jan 1, 1998

By Y Wu, F-J Ping

Today, coal production accounts for about 65 per cent of the nationÆs gross energy in China. By the year 2010, the output of coal is planned to increase to 1.65 billion tonnes and by the year 2020 to 1.9 - 2.0 billion tonnes. To meet these energy needs the Chinese coal industry is developing underground coal production on a massive scale. The new drive introduced by using direct torque control (DTC) is now proven technology for mine shaft hoisting. The drive offers unequalled speed and torque control performance as well as a low impact on the supply network by controlling the power factor to unity with a minimum of harmonics distortion.

Jan 1, 2005

By Carras S, Kelsey P, Caccetta L

An important problem in open pit mine planning is that of detennining the optimum ultimate pit limits of the mine. These limits are that contour which is the result of extracting the volume of material which provides the total maximum profit while satisfying certain practical operational requirements such as safe wall slopes. The determination of the optimum pit contour provides information that is essential in the evaluation of the economic potential of the mineral deposit. A number of optimisation techniques are available for determining this contour with the Lerchs-Grossman and the Network Flow methods being the most favoured. Unfortunately, direct application of these techniques to large ore-bodies may cause considerable difficulties because of the computational time and storage requirements. In this paper, we present a strategy for resolving these problems, and the associated pit design software PITOPTIM (incorporating a fast network flow technique) and a data reducer, BOUND. The results presented highlight the speed and power of the software package rivalling the popular Lerchs-Grossman technique. An application of the software for a sensitivity analysis is also presented and discussed.

Jan 1, 1991

The products of the steel tube industry play an important part in the production,' transrzission and refining of oil. Steel tube manufacturing is already well established in Australia and supplies the petroleum industry with its requirements" within the .present limitations of the various tube plants., With the discovery of oil in commercial quantities in this country, the steel tube industry could be expected to extend its scope to cover a much wider range; of oil country tubular goods, line pipe and refinery. Tubing.

Jan 1, 1962

By Robins R. G

The dissolution of metallic copper powder in aqueous solutions of cupric sulphate under the influence of ethylene gas was investigated. The dissolution reaction stoichiometry obtained was: Cue+(aq) + Cu(s) + 2C2H4(g) = 2(CuC2H4)+(aq) The rate of formation of the copper (I)-ethylene complex in the above reaction was studied in a laboratory autoclave and the effect pH, temperature, ethylene partial pressure and initial concentration on the dissolution rate was measured experimentally and expressed theoretically in terms of several simple conceptual kinetic models. The results led to the selection of optimum conditions for the reaction and the suggestion of an "ion-molecule reaction" mechanism to explain the very low activation energies for the reaction system. The area of application of this reaction lies in the direction of refining impure copper such as cement copper. Several experiments were performed in which an acidified solution of cupric sulphate under ethylene pressure was used to dissolve copper from the cement copper powder in the form of the copper (I)-ethylene complex, followed by the release of gas pressure to disproportionate the complex and precipitate a purer metallic copper.

Jan 1, 1987

The decision to contract or owner mine should be independent of, and should be made before, definitive estimated cost comparisons could be available. There is substantial potential risk of estimated cost comparisons being flawed due to difficulties in compiling comparable estimates for differing business objectives, errors and omissions or because of significant bias. In the current economic environment, escalating cost pressures potentially lead to increased incidence of disputes in mining contracts. The apparent cost of contractorÆs profit and overheads has tended to become more significant to owners. Economy-driven trends towards higher levels of performance and commercial risk for contractors, and the potential for more adversarial, difficult management; with attendant disputation between contractors and owners, have encouraged development of so-called ærelationship contractsÆ û partnering or project alliance contracts. The paper discusses the issues, circumstances when owner mining or contract mining is favoured and perceived advantages and disadvantages of contract mining. The implications of owner-perceived core business and core skills and outsourcing are also discussed. Techniques of introducing objectivity into the decision to owner or contract mine using matrix analysis or benefit comparisons are described. A disciplined procurement process should deliver a decision to owner or contract mine independent of, and prior to, any definitive comparison of estimated costs. A generic procurement process model is provided as a basis for discussion. Risk is discussed generally and as a significant factor in comparison of estimated operating costs. Consideration of risk and any prudent cost treatment are promoted as necessary pre-requisites to any comparison of estimated costs. The paper develops the concept that the decision to owner or contract mine should be based on real benefits that become obvious in the early stages of the development, particularly the procurement process; and before definitive estimated cost comparison can be available. In the context of this concept estimated cost comparisons tend to be confirmatory. Problems with comparing estimated ownerÆs operating costs with tendered contract prices are also discussed, particularly recovery of capital cost of equipment; and the owner minerÆs trade-off of operating risks for the residual contractorÆs margin attributed to overheads and profit. The paper concludes that sole reliance on a comparison of estimated ownerÆs operating costs with tendered contract prices in deciding to owner or contract mine is questionable and likely driven by a need to satisfy specific in-house customers.

Jan 1, 2003

In order to maintain an accurate survey underground, it is first necessary to connect all shafts used for the transferring of the survey to the levels below by a precise surface survey.This has been achieved at Mount Isa by a careful triangulation survey with stations adjacent to those shafts most suitably located for transferring the survey below.The precedure used is described herein.The Weisbach triangle commonly used is obtained by reading to swingirig wires, the theodolite being placed in line with them as nearly as is possible. The surveyor at the surface places the wires in the shaft as far apart as the size of the shaft will permit, with sufficient space between the wires and walls to ensure their swinging freely. The far wire is fixed in position, while the near one is movable by means of fine adjusting screws to facilitate its being brought into line with the fixed wire and the theodolite. When this is done the surveyor at the lower level is advised by pre-arranged signals and the survey can then commence.The surface portion of the survey is simple; all that is necessary being to read the angle from the backsight to the wires, measure their distance from the theodolite, and keep a check on them throughout the survey to make sure that no movement takes place.The lower portion of the survey is more difficult, the surveyor first qf all having to place his theodolite as nearly as possible in line with the wires.

Jan 1, 1953

By Noreen D

At Bougainville Copper Limited comparison testwork was conducted between "horizontal" cycloning and conventional vertical cycloning. Horizontal cycloning reduces circulating load and allows increased ball mill throughput. Cyclone efficiency is the same or better as a result of the reduction of fines short-circuiting to the underflow. Operationally, horizontal cyclones are less likely to suffer from blocked spigots and high cyclone feed pump sump levels. Cyclone feed pumping power is reduced. High horizontal cyclone underflow density provides the option to optimise grind by manipulating water addition to the ball mill feed.

Jan 1, 1988

An international raw material partnership, a $164 million 900,000 long ton per year aluxAna plant; an ideal location at Gladstone, Queensland, Australia - this is Queensland Alumina Limited, on stream in 1967 expanded 50 per cent by the end of 1968. Queensland Alumina Limited is the world¦s most modern alumina refining operation which is owned by an international consortium of four companies; Kaiser Aluminum & Chemical Corporation of the United States with 52 per cent; Alcan Aluminium of Canada with 20 per cent; Pechiney of France with 20 per cent; Conzinc Rio Tinto of Australia, 8 per cent. Q.A.L. operates as a co-operative -- the partners do not draw profits from the venture. Instead, each member of the consortium draws alumina in proportion to his share of the ownership. The method of disposal of this alumina is for the partner to decide.

Jan 1, 1969

With some notable exceptions, marine placers located just below, or just above, present sea level, are responsible for much of today's production of detrital ilmenite, rutile, zircon, and other minerals of value. The purpose of this paper is to discuss the paleogeographic and paleo-oceanographic factors which may have determined the location of presently submerged marine placers. These factors-include changes in sea level, burial by recent marine sediments, stream capture and other i changes in drainage patterns, and recent changes in climate. Selected geologic situations in the Yellow Sea off the coast of Korea, in the Atlantic Ocean off the coast of Portugal, in the Bering Sea off the coast of Alaska, and in the Arabian Sea off the coast of India, will be used to illustrate the author's point of view.

Jan 1, 1980

By Mousset-Jones P, McPherson M. J

This paper explains and discusses a computer program developed to deter- mine the optimum combination of fan pressures that will give a required distribution of airflows in a mine ven- tilation system. The program is based on an existing simulator, VNETPC and two experimentally developed relationships: (1) linearity between fan pressures and added regulator resistances and (2) a non- linear convex function relating the system air power and the fan operating Pressures.

Jan 1, 1988

By McKenzie C. K

During a programme of explosive performance evaluation at Hamersley Iron, Mount Tom Price Mining Operations, the relative performances of a range of heavy ANFO explosives were compared during normal production blasting operations. In addition, a number of heavily instrumented single hole blasting trials were conducted with each product type. The blasts were monitored in terms of blasthole velocity of detonation (VOD), measured using multi-point plasma conductivity probes with up to 16 measurements per blasthole. Up to 16 blastholes were monitored in each production blast. The results of measurements show a marked difference in performance of all heavy ANFO products between single blastholes and full production blasts, indicating a significant degree of interaction between blastholes in production blasting. The interaction is shown to result in a loss of detonation pressure of explosive, and considered to lead to a loss of fragmentation. The degree of interaction is seen to increase with increasing emulsion content in the products, and is more pronounced in some explosive types than others. The paper presents the methods of measurement and analysis, and the results of monitoring, together with implications on blast design and application of heavy ANFO products.

Jan 1, 1990

By Brasnett TC

A wide variety of problems are encountered on a day to day operating basis in the Isa Mine Concentrators. These vary from complex textural problems in the lead-zinc concentrator and their subsequent effect on grinding and flotation to scheduling of converter slag treatment in a chalcopyrite concentrator. With the advent of process control, metallurgists need to specialise and keep up to date with technology improvements. This paper will attempt to describe the significant problems'faced by a Metallurgist û Control.

Jan 1, 1978

Silver and gold bearing ore from the Palmarejo mine, located within the Mexican state of Chihuahua, contains a complex mix of electrum, native silver, silver sulfides and silver chlorides. This paper presents a case study that describes the selection, development and engineering of a tailored process plant for the recovery of silver and gold from this ore. Process circuit feasibility study modelling, metallurgical test work and engineering studies are outlined. Options considered to optimise the recovery of the contained silver and gold are compared, based upon cost, operability, recovery and engineering aspects. Concentration by flotation was found to be the preferred primary recovery route. Intensive leaching of the flotation concentrate resulted in solution grades sufficient to allow direct electrowinning to be evaluated against the more traditional Merrill Crowe process. The flotation tailings stream is processed through a separate leaching stage as there is sufficient economic metal extractable from this stream. The processing flow sheet, which is designed to maximise the recovery from both the flotation concentrate and tailings, and to utilise a common metal production facility, is presented.

Jan 1, 2009

By P F. Knights

Mining companies are striving to achieve new levels of operational maturity and drive process improvement across the organisation in the face of unprecedented demand and limited supply of experienced human resources. Advanced analytics techniques can help overcome these fundamental challenges by applying data techniques not previously applied in mining. Today, decisions are usually locally optimised but do not achieve optimum capability for the value chain. Although more information is collected then ever before, it is difficult to link many sources of data together in the same place in real-time, for example plant history, maintenance, mine planning, logistics and engineering data. Consequently complex analysis of data is time consuming and requires specialist skills and knowledge, and is often neglected in the decision-making process. In the future, analytics will close the loop between analysing data and taking action. Analytics will become embedded in the business and routinely applied to improve decision making across the organisation, from senior management to operations and maintenance workers, but will not require specialist skills or be time consuming to analyse data. As analytics becomes embedded in the business process, decisions are supported by data (not on gut feel), and critically, data from many sources are integrated in real-time to improve the quality of decisions. Ultimately, predictive tools will help suggest, or even in some cases automate, courses of action. The main opportunities for analytics exist where the enterprise requires supporting technology to enable it to continue to evolve to higher level of maturity. This will be in the areas of asset management, rapid reconciliation and adaptive planning, and the inbound and outbound supply chains. Advanced analytics are also a key enabler for increasing the effectiveness and realising the true value of Remote Operations Centres to safely and efficiently support operations in remote locations with smaller workforces.

Jan 1, 2008

By Ishikawa K, Kikuchi T, Tokairin Y

Roadheader, developed from coal cutting machines, is generally classified as a tunnel excavation machine for soft rocks in respect to excavation mechanism, machine structure, weight, engine output and so on. In recent tunnel works, however, there is an increasing demand for changing from blasting to mechanical excavation by roadheaders to avoid environmental problems such as noise and vibration. But there exist various difficulties in excavation of harder rocks by roadheaders. In order to explore the possibilities of roadheader excavation, we performed field and laboratory experiments. In the field experiment, roadheader model S-125 (Mitui Miike Machinery Co.,Ltd.) was tested for various rocks of wide range of hardness, and excavation capacity and wear of picks were measured. In the laboratory test, cutting performance of the picks was tested by our cutter testing machine. This report describes thr: of these experiments and discussions :n possibility of applying boom-type tunnelling machines to hard rock excavation based on these experimental data.

Jan 1, 1987

The treatment meIhods selected for the concentrator at Cobar Mines Pty. Ltd. called for a high degree of automatic control of both the grinding and flotation sections.The resulting concentrator layout includes a central control room overlooking both grinding and flotation sections. The control room houses process recorders, controllers, and indicators. together with motor stopstart stations and alarms.Plant instrumentation includes load cells and variable speed hydraulic drive feeders for feed-rate control of autogenous mills, together with nuclear density gauges, differential flow transmitters, and pneumatic control valves for water and pulp density control.Flotation cell pulp levels are controlled by floats and pneumatic actuators; flotation reagent controls include magnetic flowmeters and time-operated solenoid valves.

Jan 1, 1969