Search Documents

By Mackinnon I. D R, Glikson M

Samples from the Callide Coal Measures, Queensland, Australia, containing the minor maceral, micrinite, have been studied using optical and electron-optical techniques to determine the precise compositional and structural nature of micrinite when in association with vitrinite macerals. Emphasis has been placed on direct spatial correlation of optical and electron-optical data due to the fine grain size (90 per cent of the component) and, as such, should not be considered a maceral.

Jan 1, 1991

By Wang S

Fragmentation is the basic concern in rock blasting and serves as the main measure of blasting effectiveness. A good estimation of fragment size distribution before blasting is very useful and helpful for selecting the proper equipment for loading, transporting, and crushing rocks. A fragmentation model is presented that is based on a hole by hole analysis and correlates the rock properties, burden, spacing, and explosive column with the blasted volume and fragmentation obtained. The drill bench is divided into three separate areas corresponding to different breakage mechanisms. They are: 1) a main breakage or casting area, 2) a secondary breaking area, and 3) an overbreak area. The boundary of the main breakage area is found from the magnitudes of strains in the stress waves and the tensile strength of the rock. The secondary breaking area is determined by stress wave reflections at discontinuities and interactions between colliding stress waves from adjacent boreholes. The overbreak area is that beyond the main breakage area "where the reflected tensile waves no longer break the rock. This analysis is applied on a hole by hole basis to locate the breaking points. Then connecting the breaking points on each side of a borehole forms the triangle of the main breakage area. This is repeated for the next hole and the remaining area is the secondary breakage area. After the angle and area for each hole are found the Kuz-Ram model is used to predict the fragmentation size distribution for each hole. Then summing up the size distribution for each hole gives the total fragmentation distribution. This analysis has been successfully applied to field tests performed in a limestone bench where the entire spoil pile was screened to determine the fragment size distribution. Knowing the explosive and rock properties the breaking area was found for each hole, the strain and stress values, the breaking point, and angle of breakage (104 degrees). The fragmentation size distribution was then calculated and compared to the field data with excellent agreement.

Jan 1, 1990

By Evans A, Jones O

Surface subsidence resulting from "total extraction" of coal in the Collie Basin first occured in 1987 when Western Collieries Ltd trialled the Wongawilli mining method. Because very little quantitative subsidence data existed for the weak, Permian sediments, a research program was set up prior to the extraction of the first panel. The objective of the study was to be able to predict subsidence characteristics and effects prior to mining future total extraction panels. Attempts at predicting subsidence began using existing subsidence models from other coal mining regions, however, as more site information became available, it became clear that it was necessary to develop a separate, she specific predictive model for the Collie Coal Basin. Analysis of extensive field monitoring data for both surface and subsurface subsidence has produced a series of empirical models which can predict the shape of surface subsidence troughs and corresponding tilts, and strains for rectangular panels and describe the sequences of ground movement from the mine roof through to the ground surface.

Jan 1, 1992

A shift in the present day oil exploration scenario from West Coast can be foreseen keeping in mind peak of exploration in Cambay Basin and fast pace of development in Bombay High and its associated fields by the end of this century. Shifts in exploration from structural traps to stratigraphic traps, techno- logical development to drill in deep waters, improving economic situation for oil ventures and proven oil and gas potential of East Coast basins suggest that Indian oil explorat- ion scene will be at its peak along east coast during early 21st century. Hydrocarbon shows in Poonch and Jawalamukhi in Punjab Basin, improvements in drilling to greater depths, better seismic data aquisition, good source rock potential of Subathus and its equivalents and large geologi- cally mapped structures will reopen new avenues for explorationists. Not much exploration effort has been put up so far in Ganga Basin. Keeping in mind size of the basin, sedimentary thickness involved, presence of algal matter deposited in shallow marine environment & higher hydrocarbon indications warrant active exploration. Gondwanas in India having such a large sedimentary area can not be ignored keeping in view generation and production from the non marine sediments of Kenya, Chad, Sudan, Gadon and China. Gondwanas become all the more important in view of gas production from their equivalents-Karoos in Ethiopia and South Africa. In all, above mentioned changes can be predicted in Indian oil exploration scenario during 21st century.

Jan 1, 1986

By Albano C, Antila A, Flykt B

A method for relating operating variables and dewatering parameters of Thunes disc filters in the LKAB pelletizing plant at Malmberget in Sweden, via empirical mathematical models is described. Near orthogonal experimental design was used, where all independentvariables were allowed to span over their domain of variation and pseudo-randomly distributed among the experiments. The dewatering parameters are dependent on many variables and instead of using a traditional mechanistic model, an empirical model based on multivariate data analysis was chosen. The way of expressing the relation is by regression coefficients obtained from partial least square regression (PLS). Two empirical models were generated. The models were validated using an extra set of 56 experiments. The dewatering parameters were related to the design variables with few experiments, and user-friendly response surface methodology was used to determine the optimal conditions.

Jan 1, 1989

A recently discovered high temperature (22G-2800°C) reaction between glycerol and the oxides and hydrous oxides of iron produces a green, well-crystalline complex glycerato-iron, whereas hydrous nickel oxides an) reduced by the glycerol to metallic nickel. When nickel isomorphously substitutes for iron within the goethite lattice this high temperature glyceration allows a separation of the two metals whereby the nickel can be extracted by solution techniques.

Jan 1, 1971

A broad zone of intra-plate volcanism occurs for some 3000 km along the E. Australian coastal regions, extending from far northern Queensland southwards to Tasmania, westwards to western Victoria, and into southeastern South Australia. The age range, taken over the whole region, extends from Eocene to Holocene. Wellman & McDougall (1974) recognised the occurrence of three distinct types of volcanic occurrences: (a) Lava field provinces, dominantly basaltic and commonly strongly undersaturated, but of variable size. Large lava fields are especially exemplified by the younger provinces in northern Queensland (e.g. Nulla, McBride), and western Victoria. (b) Central volcano provinces, in which a reasonably well defined volcanic edifice is discernable. Such provinces are built of mildly undersaturated to saturated mafic lavas, but are also characterised by felsic volcanism (and often substantial mafic and felsic intrusive phases). Examples are the Springsure-Minerva Hills province, the Tweed and Focal Peak Shields (southeastern Queensland to northeastern N.S.W.), and the Nandewars, Warrumbungles, and Canobolas volcanic centres (N.S.W.). (c) A single leucitite province in N.S.W. Wellman and McDougall (1974) were able to show that the central volcano provinces exhibit a remarkably regular southward age migration pattern, the calculated migration rate being 66 + 5 mm yr , and these authors interpreted this in terms of the northward passage of the Australian plate across a fixed 'hotspot' within the upper mantle. The leucitite province also fits this migration pattern. The lava field provinces apparently exhibit more erratic regional age distribution patterns, but Sutherland (1981) has interpreted the data in terms of a multiple 'hotspot' model. It is noted, however, that the youngest areas of volcanism (Pleistocene 1. Department of Geology and Mineralogy, University of Queensland, St. Lucia, Brisbane, Queensland

Jan 1, 1987

By Ramsay WRH

The Mount Stavely Volcanic Complex compri- ses one of a number of northerly trending fault bounded greenstone occurrences in Western Vict- oria, of probable Cambrian or older age. The greenstone belt is coincident with several linear positive aeromagnetic anomalies, which outline the surface and subsurface extensions of these greenstones. Mapping at Mount Stavely has identified serpentinite, variolitic basalt, two-pyroxene and pyroxene-hornblende andesite, dacite, rhyodacite and their pyroclastic equiv- alents. Chemically and mineralogically the volcanics constitute a calc-alkaline assemblage. The mineral potential of the region has been enhanced following a discovery by Pennzoil of Australia Limited near Ararat, of sulphide min- eralisation containing approximately 1 million tonnes at 2.7 percent copper. The volcanic environment of the Mount Stavely Volcanic Complex is discussed in terms of similar environments found in Canada.

Jan 1, 1982

Roadheaders have had a chequered history in hard rock excavation in Australia since their introduction into the country in 1972. This has resulted in a poor reputation among both clients and contractors and subsequent reluctance to design tunnels and underground space around their performance characteristics.This has now changed because of the introduction into Australia of a new breed of Roadheader, the Mitsui. This paper sets out the history of development of the Mitsui range of Roadheaders. It describes the process which resulted in the introduction of this new machine, its performance to-date and the characteristics which have contributed to the success of the machine. The combination of these factors have led to a change in attitude to the use of Roadheaders in underground excavations.

Jan 1, 1993

Systematic ICPES (Inductively coupled plasma emmission spectrometry) analysis of magnetic concentrates from drainage samples has been used to discriminate concentrates dominated by magnetite from those dominated by pisolites, presumably maghemite-rich. In addition, a set of spurious zinc enhancements was recognised and explained with the help of mineralogical data, and systematically isolated using chromium as a Discriminator.

Jan 1, 1987

By Ellson I. G

Advantage has been taken of the need to build the new mining town of Shay Gap to incorporate a new standard of living in an isolated area, which suffers from climatic extremes. The various problems associated with living in the Pilbara area of Western Australia are outlined, together with their effect on the design of Shay Gap.

Jan 1, 1973

Optimisation and sensitivity analysis of final pit limits is now an accepted procedure for open pit planning studies. Tools to assist the design engineer in an underground metalliferous mine to make optimal choices for the selection of major development, stope geometry and cut-off grade analysis have not been available. The engineer has had to rely on experience and a limited analysis of design alternatives. A new tool called the `floating stope' has been developed to define the optimal (boundary) limit for material that can be economically extracted by underground stoping methods. The method is analogous to the `floating cone' method of open pit optimisation. The geology and mineralisation are modelled as a regular or subcell block model. Included in the model are structural and geotechnical features, and any previously mined out areas. Inputs to the procedure include the minimum stope dimensions, cut-off grade, stope head grade, and the way in which dilution is to be calculated. The optimisation procedure can be directed to maximise ore tonnes, grade, contained metal or the economic (dollar) value of material mined. The procedure can be applied at each stage of mine evaluation and design to assist with preliminary resource appraisal, selection of stoping methods, and detailed mine design. As with open pit optimisation procedures, manual intervention by an experienced engineer is required to produce practical and detailed designs. This practical design should follow the optimised design as closely as possible. The paper outlines the algorithms used in the definition of the stope envelope, and describes the analysis and results of several case studies where the optimisation procedure has been applied.

Jan 1, 1995

By Wharton P, Voigt R

In order to do the discharge estimation better, it is valuable to find out appropriate formulas for estimating discharge in various pits, based on accumulating data, summarizing discharge patterns applying optimum seeking method and principle, by seeking redical exponent with help of the method of exhaustion, as well as testing and making statistics, in accordance with the quality standards established by our practical experience.

Jan 1, 1988

By Wright G. N

Curragh Queensland Mining Limited, a co-venture of Australian and overseas interests, operates an open cut coal mine 13 km north of the township of Blackwater in Central Queensland, refer attached location map.

Jan 1, 1992

By R Balusu

This paper provides an overview of computational fluid dynamics (CFD) modelling capability developed by CSIRO with the aim of improving the knowledge of flow migration dynamics within longwall goaf areas. The CFD models can be used to study the ingress of oxygen into the goaf in different ventilation scenarios and goaf drainage arrangements. This approach not only helps the design of effective gas control strategies but also the management of spontaneous combustion risk in the goaf. Innovative goaf inertisation strategies have been developed and implemented during longwall sealing operations. Work is continuing to develop general guidelines of proactive goaf inertisation strategies to suppress the development of spontaneous heating behind active longwall faces.

Jan 1, 2005

Portable crushing at Duval Corporation's Sierrita open pit mine has proven both the economics and operability of large, hardrock, portable systems. In-house expertise was utilized to create a system incorporating both operational and maintenance features requested by operating personnel. The monitor/control system involves over 400 channels of information and is based on a DEC 1SI 11/2 microprocessor communicating with seven microprocessor-based data acquisition systems over a 4-wire, multidrop link. The year and one-half successful operation affirms the design philosophy and the hardware/software implementation.

Jan 1, 1985

By T C. Hunter

There are unique risk factors involved in the development of an Australian uranium project especially by a æjuniorÆ. These encompass a range of political, technical, environmental, regulatory, timing, native title, investor relations and financial issues. The Honeymoon Uranium Project in South Australia is being developed by Southern Cross Resources. The history and experience from a risk viewpoint is detailed and discussed. Particular emphasis is placed upon the practical experience and obstacles overcome to meet project milestones.

Jan 1, 2003

The bulk and surface chemistry of metal ion hydrolysis and precipitation and the redox chemistry of metal ions, sulphur, and other species is central to an under- standing of flotation. The paper contains a review of general hydrolysis-redox chemistry appropriate to the flotation process, and a model of natural and collector-induced flotation of sulphides is constructed. The practical application of the model to real flotation systems is then explored with a view to better under- standing of the chemistry of selectivity and grade control.

Jan 1, 1984

IntroductionHistory of MineTopographyGeology of AreaGeneral DescriptionIgneous Rock TypesGranodioriteQuartz monzoniteApliteGranite porphyryMetasomatic ActionAlteration of monzonite/Alteration of apliteGeology of Ore BodyNature of OreZones of MetasomatismAssociated Fracture PlanesDistribution of Copper MineralisationNature of Copper VeinsQuartz-chalcopyrite veinsQuartz-calcite-chalcopyrite veinsEuhedral quartz veins/Non-euhedral quartz veinsStructures Accompanying Ore BodyApliteIntersecting lines of metasomatised monzoniteMetasomatised aplite

Jan 1, 1949

The products required by customers today have become far more complex and consequently more demanding to handle. And thereÆs the dilemma. Nowadays, people tend to stick to a trade for just a few years instead of for a lifetime, and this means that the customerÆs employees cannot be expected to get more than general knowledge of how to handle modern mining and construction equipment. To meet this challenge, major steps are being taken by suppliers to make their æmusclesÆ more user-friendly. Also the supplier is assuming a larger share of responsibility for the product including operators training, supply maintenance services and, in many cases, performance guarantees. In other words, the supplier is today supplying a function or an activity rather than just muscles. Some of the new generation drill rigs have been on the market for a few years and reliable experience has been collected and is addressed in this paper. Some of the information is well supported by figures while others are just statements from users of the rigs.

Jan 1, 2005