Search Documents

By Zamel G. I, Zenari L. P

Technological developments in modem Tunnel Boring Machines (TBMs) and associated back-up equipment are offering significant alternatives for mining operators to consider, in the selection of equipment for coal mine development drifts, roadways, longwall gate roads as well as metalliferous mining declines and development drives.Greater flexibility in handling variable ground conditions, muck disposal and radius of turn as well as advance rates, are just some of the areas where modem TBMs can accomplish the flexibility that mine operators require to achieve cost-effective developments.Compact TBMs are achieving this acceptance because of the fundamental design of a shielded machine containing electrics and hydraulics within the forward shell, ability to achieve tight radius of curvature and grades, and ability to provide highly flexible support systems to meet all possible ground conditions.However, a single TBM design will not suit all mine developments, as each development method - while having common goals with all mine developments - will also require certain unique criteria to be fulfilled.

Jan 1, 1993

By Johnson M, Wooltorton B

A programme of hydraulic fracture stress measurements conducted in surface drill holes along the alignment of the King River Power Tunnel has provided information of importance to the assessment of the extent of steel lining requirements for the tunnel. A significant horizontal stress field has been detected at a location remote from the power station site, with a corresponding absolute minimum stress magnitude approximating the overburden pressure based on depth of cover. Measurements made closer to the power station site (located toward the bottom of a valley) have revealed an apparently relatively destressed region with minimum stress magnitude less than overburden pressure. The implications of these results are discussed.

Jan 1, 1987

The firing of mass blasts at Isa Mine is a normal operating practice. Both electric and non-electric initiating systems are being used for this purpose. The advantages gained by large firings relate to the Planning, Scheduling, Services and Production functions of Isa Mine. More efficient us"e is made of manpower due to the concentrated charging effort and con- tinuity of the charging operation. In addition, the requirement for ring firing personnel to work at the edge of large stope voids is reduced. Better fragmentation results from the interaction of adjacent detonating rings of blastholes and in flight collisions. With mass blasts there is also less chance of large blocks of ore, created by faults or joints, falling into the stope and creating problems at the drawpoints. The formation of a large tonnage of broken ore facilitates production at scheduled rates from that stope source. The weight of explosive detonating during a mass blast can be considerable. Isa Mine has achieved satisfactory blasting results without excessive ground vibration levels and present knowledge indicates that pillar ground stab- ility has been maintained.

Jan 1, 1978

By Mark C

Designing coal pillars to provide resistance against overburden loads has long been an aim of rock mechanics engineers. The need for accurate pillar strength models has become.more urgent as greater overburdens are encountered and pillar sizes grow larger. Current pillar design models differ widely in their predictions of the trend in pillar strength with increasing pillar width- to-height ratio. The goal of this paper is to evaluate current pillar strength theories, using a comprehensive data base of stress measurements from coal pillars. The stress measurements indicate that coal pillars maintain relatively high stresses near the ribline, and that the stress gradient within the yield zone can be approximated as a straight line. Several problems are identified for further research, including calibration procedures for different types of stress cells, strain softening behavior in the yield zone, and measurement of stresses in the cores of very wide pillars.

Jan 1, 1992

Economic conditions dictated the lead time from concept to commissioning of the Kambalda C.I.P. Plant. The high gold price prevailing at the time the Victory ore-body was discovered provided the impetus to establish a treatment plant with the utmost haste. Consequently only limited metallurgical testing was possible. Fortunately the Kambalda Metallurgical Department had experienced gold metallurgists among its' staff. This enabled a rapid assessment to be made of the ore types to be treated. Flexibility was the keynote in the plant design. Overseas practice and experience was drawn upon extensively, but it was known that problems uniquE to the Kambalda Plant would be encountered due to the high nickel content of the C.I.P. Plant feed and the difficult clays in some of the areas. These fears were well founded and problems have been experienced. However the plant design has enabled these problems to be absorbed, if not overcome, and design production rates were achieved and maintained within three month; of start-up.

Jan 1, 1982

The current quantity of rejects from coal beneficiation in Australia represents 20 to 25% of raw black coal production. Approximately 80% of the rejects are derived from coarse processing for particles in the 200mm to 0.5mm size range. The safe and enviornmentally acceptable storage of coarse coal rejects is of interest to coal mining companies. Additional public benefit would be derived from the utilisation of a waste product as a source of fill material for civil and mining engineering applications. BHP Engineering has taken a leading role in the design for storage and utilisation of coarse rejects from two mines associated with the Broken Hill Proprietary Conipany Ltd. The tailings dam at Stockton Borehole Colliery (N.S.W.) is to be raised and a study by BHP Engineering has shown that coarse rejects are suitable for the formation of the supporting embankment surrounding a compacted clay core. Transportation and storage of coarse rejects at the Thiess Dampier Mitsui Riverside Mine (Moranbah, Qld) is achieved by a conveyor leading directly from the coal preparation plant to a discharge stacker on the crest of the rejects stockpile. Production of coarse rejects was higher than anticipated for the initial dump design. BHP Engineering has completed a review of dump design with emphasis on safe operating conditions for the conveyors and stacker system. Data on the geotechnical properties of coarse rejects from Australian coal mines are presented. Coarse coal rejects are a material which should not be considered as waste, but as a potentially valuable resource for many future applications. Appropriate engineering design for the storage and utilisation of coarse rejects would result in an improved environment and economic benefits for the Community.

Jan 1, 1987

By W J. Shaw

Geometallurgical modelling is now a hot topic in deposit evaluation and in optimising mine performance; however, its history is long and varied. Historically metallurgical sampling has frequently suffered from a lack of data due to the cost of producing representative bulk samples. In the early 1990s geometallurgical modelling similarly suffered from a lack of data due to complex, time consuming and expensive sampling techniques. More recently, simple and relatively cheap tests for geometallurgical variables such as hardness, grindability, throughput, SAG power index, bond work index, crushing index, mineral recovery and concentrate grade have become widespread. The cheaper sampling has resulted in relatively large geometallurgical databases. However, most of the geometallurgical variables sampled are implicitly (and incorrectly) assumed to be additive when modelled by traditional geostatistical techniques, often leading to ill-informed and costly decisions. Geometallurgical variables are mostly non-additive so the current geostatistical challenge is to develop new approaches to dealing with this type of data. This paper briefly describes a historical case study of geometallurgical modelling of the George Fisher Pb-Zn mine completed in the mid 1990s, then outlines some of the current misconceptions of geometallurgical data and modelling techniques regularly applied to it, and finally discusses some recent developments in geometallurgical modelling, with examples from a number of current clients indicating the direction forward.

Jan 1, 2009

China has large amounts of iron ore reserves, but iron ore in China, with low-grade, small disseminated particles and many other associated minerals, is difficult to dress. In recent years, with the fast development of China's steel industry, the demand for iron ore has increased markedly. The new technologies in iron ore dressing in China are very effective in processing haematite and other difficult to dress iron ores. The iron ore grade and recovery rate has been improved. This result alleviates the difficulty in iron ore supply in China.

Jan 1, 2007

By Pathan AG

This research work is concerned with an investigation of the fracture toughness of sandstone, siltstone, and coal. Tensile failure trades have been examined with three different specimen geonetries, i.e; rectangular bar, round bar (in three point bending), and diametral compression discs. The Stress intensity approach, and J-integral methods were used to evaluate fracture toughness. Results from both approaches are discussed. True crack length was determined after pre-cracking, using the compliance calibration technique. Fracture toughness results of sandstone are independent of crack length and the size of the specimen. Fracture toughness may hence be regarded as a material property for sandstone. In cxnntrast fracture toughness values for !siltstone and coal are dependent on crack Length.

Jan 1, 1986

By Hogan C. J

The compact BWE system set up in 1984 to mine ironsand dunes and the underlying ironsand-clay has been an effective high volume produc- tion unit for New Zealand Steel Mining Ltd at the Waikato North Head ironsand mine. The system utilising two compact S400E (0 & K) Bucket Wheel Exca- vators and a single shared Beltwagon for transfer to the shiftable bench conveyors replaced a fleet of mobile elevating scrapers when the produc- tion requirement was increased by a factor of six. A key factor in favour of the BWE system was the economic advan- tages of low unit costs for both manpower and electrical energy.

Jan 1, 1989

Traditionally, surface coal mines in the Western United States have been limited by economics to depths between 150 to 200 feet. Utah International Inc., however, is now planning to strip coal its San Juan Mine in Northwestern New Mexico to depths ranging up to 400 feet while uncovering 20 feet of steam coal. This method is cost-competitive with nearby shallower coal deposits and underground mining of the same property. How trucks and shovels can pre-strip for a dragline, along with results of the planning process, comparison with alternate systems, capital requirements, operating costs and comparisons with other coal sources are all detailed. Also discussed are the major problems anticipated, how they might be corrected, and potential improvements to the concept. Introduction The San Juan Deep Stripping Project will be situated at Utah International's San Jean Mine. The mine is in the Four Corners region, so-called because four states enjoy a common border point about 30 miles to the northwest.(see Figure 1). The area is a semi-arid plateau region with an average elevation of 5,200 feet, receiving an average of 6 inches of precipitation annually

Jan 1, 1981

By D Thornton

Geologists use large data sets and spend many hours and much computing time modelling the distribution of minerals throughout a rock mass. Significant investments in drilling, assaying and quality assurance and quality control (QA/QC) are made before sophisticated geostatistical techniques are applied to the collected data. A large amount of research has been done in this field such that the ore control model is a reasonably accurate reflection of the mineral that is actually in the ground. However, after all this effort, the mining engineers then work just as diligently to blast the in situ rock mass to a particle size that can be efficiently handled and further reduced by downstream comminution processes. In open cut mines, this invariably requires large amounts of explosive energy that displaces the ore boundaries from where the geologists originally defined them. Failure to accurately account for blast movement will result in misclassification, whether that is ore to waste; low grade to high grade; sulfide to oxide; or other contaminates û collectively referred to as ore loss and dilution. The financial consequence of getting this wrong is substantial and not well quantified. This diminishes all of the good geological QA/QC done in defining the ore. This paper discusses various technologies used to physically measure blast-induced orebody movement and the difficulties in modelling this with a purely theoretical approach. Rock mass structure, blast energy, design and timing contours all have significant and interrelated effects on blast movement vectors. Measured blast movement has a large variance due to the uncertainly of many of the controlling parameters û arguably dominated by the heterogeneous nature of the rock mass. Although there have been significant advances in blast movement modelling capability in recent years, this unpredictable blast movement limits their use in the context of production ore control. Certainly, without physical field measurements, accurate predictions of movement are near impossible.Limitations of traditional surface markers in determining three-dimensional (3D) blast movement within the orebody are also reviewed, and advancements in accurately measuring these vectors within blasted ore discussed

Sep 26, 2011

By Fleming GJ

The Miwah prospect lies on the dilational 070¦ trending Miwah Lineament near its intersection with northerly oriented fractures within Pliocene volcanic rocks exposed between a NW trending segment of the dextral transcurrent Sumatra Fault, and the more northerly trending Samalanga-Sipopok Fault to the east. These faults reflect the continued interaction between stresses from the India-Australia plate located to the southwest, and spreading within the Andaman Sea to the north of Sumatra. A system of deep seated faults is believed to have facilitated emplacement of post-Miocene magmas and Quaternary volcanic centres at shallow crustal levels throughout northern Sumatra.

Jan 1, 1995

The original design of the Bougainville Copper Limited (BCL) concentrator took cognisance of the constraints imposed by the topography, the need to minimise capital cost, and the need to allow for plant expansion which, it was known, would be necessary to maintain copper and gold production as head grades declined.At the same time as spare slots have been taken up with additional equipment, technological innovations have been embraced whenever there appeared to be a chance of improving the productivity ofexisting equipment, or replacing it with a more efficient alternative.There are many examples of this in the BCL concentrator in the areas of process control, process design, instrumentation, materials handling, equipment design and wear part technology.Current process developments also pursue the latest technology. The development of the Omnicone crusher, flotation control, tailings water reclamation, and the variable speed gearless drive on the No. 13 mill are prime examples.

Jan 1, 1986

This paper gives a first-hand account of what a graduate mining engineer can learn by visiting Atlas Copco in Sweden and gives reasons why all mining engineering students should apply for this excellent scholarship. It will also (attempt to) refute the authorÆs mine managerÆs claim that the trip was a huge junket.

Jan 1, 2006

To gain further understanding of the operating efficiency of the BHP Slab and Plate Products Division (SPPD) RH vacuum degasser, physical and mathematical model studies of the process have been undertaken. The purpose was to investigate how the various process parameters affect the liquid circulation rate, to visualise the flow patterns, and to identify and eliminate the cause of localised wear in the downleg. In the physical model mixing times were measured using an acid tracer technique. The results were applied to predicting trends in times required to obtain homogenous melt composition under varying conditions. A 2-dimensional mathematical model describing the liquid metal flow has been developed using the PHOENICS fluid-flow package. The physical model results were simulated and incorporated into the mathematical treatment and an improved design for vessel geometry is proposed. The effect of rounding the downleg entrance or installing a baffle between the legs is discussed.

Jan 1, 1987

Blasting is known to be both an important and an easily quantified cost factor in rock breaking operations. However, the indirect costs and benefits of the blasting operation are not easily determined due to the irreversibility of the mechanisms involved and the multiplicity of influencing factors. A general conceptual model showing the relationship between blasting and mining costs is well known, but serious attempts to address the critical real relationships have all floundered on the fact that not enough is yet known about either detonation physics or blasting effects. This can only be remedied to the extent that blasting instrumentation enables researchers to pin down not only the relationship between the detonation process and its impact on a particular environment, but also the downhill costs of handling the rock, repairing any damage and building in "Safety Factors" to provide for imponderables. It is vital to standaraize on specifications for instrumentation and measurement techniques and there is a need to review what has been achieved in blasting expertise so as to focus on the most fruitful paths for future work.

Jan 1, 1990

The Mesozoic intrusive rocks in southeastern coastal China can be divided into three intrusive suites, and they can be brought into corresponding with four cycles of volcanic activity. This paper describes their time-space relation with volcanic rocks, and their geochemical characteristics. Data from the Mesozoic volcanic-intrusive. complex rocks in Eastern Zheijiang, Eastern Fujiang and Eastern Guangdong show distinct regional differences, both within and tectonomagmatic activity regions. The southeastern coast of China involves four tectonomagmatic activity regions. They have many differences on the nature of magma source regions, activity patterns of magma, time-space distribution, petrography and petrographic facies association of volcanic and intrusive rock and mineralization.

Jan 1, 1990

By M Bannear, J-F Wilhelmy, R Jones

Mineralogical study of the interactions between fluxes and iron-oxides helps to understand how magnetite oxidises to haematite during pellet firing. Samples of OneSteel magnetite pellets tested at COREM pilot plant were collected after three firing steps and were studied mineralogically. Preheated pellets revealed no particular microstructures related to the composition of fluxes but were more affected by their bed position. After kiln firing, the impacts of lime and magnesia became more apparent. Magnetite oxidation is complete in the cooling stage. The position and the microstructure of the residual magnetite can bring useful information that could æcompleteÆ the view of the firing cycle.

Jan 1, 2007

By D P. Telionis, P P. Vlachos, R-H Yoon

Industrial processes involving multi-phase flows such as flotation require understanding of the relationships between bubbles, solid particles and the flow. Modern experimental tools are employed in this effort to measure with great accuracy the basic features of the motion of all three phases in turbulent flow. We employed a unique digital particle image velocimeter (DPIV) that can record with great accuracy and kHz temporal resolution, velocity vectors of all three phases, namely the fluid, the solid particles and the air bubbles. The interaction of these three phases was studied in homogeneous isotropic turbulence generated by cylindrical grids. Particles and bubbles were released into the turbulence and the motions of the three phases were monitored. The experimental results obtained in the present work were compared with the predictions of the models published in the literature.

Jan 1, 2005