Search Documents

By Still RF

Sintering of lead and zinc concentrates is practised by Sulphide Corporation Pty. Limited to provide both desuiphurised lump sinter feed, for simultaneous reduction to zinc and lead in the Imperial Smelting Process blast furnace, and sulphur dioxide gas for sulphuric acid manufacture. From November, 1969 a 20 percent increase in production rate has been obtained through improvements in operating technique. A gradual increase in bed permeability was achieved by modifications to the feed mix conditioning equipment and by improving moisture control. However advantage could not be taken of the higher permeability to increase sulphur elimination because the hardness of the lump sinter decreased. Higher throughput, better quality sinter and more stable sintering conditions were however made possible by simultaneously: 1. reducing segregation and compaction in the sinter bed, by narrowing the discharge opening of the main layer feed hopper, 2. reducing the sizing of sinter returns to give a closer size spectrum of particles in the feed mix, and 3. increasing the sulphide sulphur content of the feed mix to give higher bed Temperatures.

Jan 1, 1972

By A Scrase, J Brereton

The Latrobe Valley is located approximately 150 kms east of Melbourne. Within a very small area there are 3 large brown coalmines and associated power stations, 3 large towns, and numerous smaller towns in the vicinity. The mines have been generating power for Melbourne and surrounds for the last 100 years, with two of the mines being owned and operated by the Victorian Government (State Electricity Commission of Victoria) prior to privatisation in the 1990s. All three mines were privatised with the expectation that the mine voids would be filled with water to become pit lakes, as the final landform/rehabilitation solution (Hazelwood Mine Fire Inquiry, Teague and Catford, 2016). It could be argued that until relatively recently, this was largely expected, by government and industry, to be the rehabilitation solution for managing the two key risks associated with the sites:  The geotechnical stability of the mine pits.  The prevention of fire – through covering coal batters with water. Transitioning away from mining economies requires collaborative, regional, innovative thinking with a multitude of stakeholders, from a wide range of government departments, industry, First Nations people and broader community. Closure planning and rehabilitation activities require a range of skills and experience, such as, closure planning, various scientific and engineering disciplines (pit water quality modelling, geochemical modelling, cover design, landform design, contaminated site etc), civil engineering, demolition etc. Some of these skills are similar, such as financial modelling, stakeholder engagement, contract and project management. But the majority are different to those required during the operational phase of a mine. These closure skills can also be lacking within government, with Departments more familiar with monitoring and compliance activities associated with operational facilities. Some key aspects that appear to be critical to planned successful closure are:  Collaborative regional and localised planning, with industry, government, community, First Nations and other industry, business leaders and entrepreneurs all involved in providing a smooth transition away from mining.  Well-defined and known regulatory pathways to achieve mine licence relinquishment assists in encouraging investment.  Appropriately skilled and experienced government and industry personnel.  Mining companies, who are committed to closure planning and provisioning from the earliest point in project planning.  Mine employees who are appropriately skilled and experienced in mine closure planning and implementation with access to all the relevant technical expertise required for the project. Areas like the Ruhr Valley in Germany provide good some examples of smooth processes that facilitate mine economies transition into new economies (World Resources Institute (WRI), 2021).

Aug 2, 2023

The Curragh coal mining operation was designed and constructed to produce two coals initially at a rate of 4.3Mtpa. These are a high thermal energy steam coal primarily for domestic electricity generation and a low ash high quality coking product for the export market. Treatment of coals from four seams to achieve this requires a large and complex preparation plant and blending facilities incorporating state of the art technology. This facility was constructed during 1982/83. It has been designed for expansion to 6.8Mtpa capacity. The preparation and handling facilities were built at a cost of approximately A$80 million. Equipment includes 500 plus electric drives with a total capacity of 20 000kw. Commissioning was carried out in three phases : Staging - of the control system Coal Handling Facilities - conveyors, stackers and reclaimers for raw and product coals The Coal Preparation Plant - heavy media cyclones and froth flotation. A period of three months was devoted to the commissioning of the plant before requiring product coal to contract specification. This paper will describe the planning, implementation and results achieved.

Jan 1, 1986

Data collected from payload management systems at a number of surface mining operations show significant variance. Heavily loaded trucks travel slower up ramps than lightly loaded trucks. Faster trucks are slowed by the presence of slower trucks, resulting in 'bunching' and production losses. A stochastic model was constructed to simulate a truck haulage return cycle of 12.5 km at a large open pit gold mine in the USA. For a fleet of 35 trucks, the best estimate of the benefit achieved by a sustained reduction in payload variance of 25 per cent is a throughput increase of 1.6 per cent, within a possible error range of 0.6 to 3.2 per cent. This potential benefit is worthy of further investigation by Continuous Improvement teams at large open pit mines. The model also indicates that, under the right circumstances, provision of an overtaking lane can provide throughput benefits of up to ten per cent, The feasibility of providing unidirectional haulage circuits within large open pit mines should be examined.

May 1, 2010

A continuing demand for exploration geologists, at a level well below that during the mineral "boom" of 1967-1971, will be highly selective. The exploration geologist must be more than the traditional geologist whose primary function has been detailed description of rocks and their recording on a geological map. He must be capable of 1. reconnaissance recognition of favour= able environments for ore mineral concentrations, 2. application and interpretation of techniques of search and evaluation, and 3. evaluation of economic, technological and political interactions that combine to make an ore deposit. Universities have an obligation to their students to provide them with a saleable skill, to educate them so that they can cope profess- ionally and socially, and to provide a mechan- ism by which education can be a continuing process. Humanistic and social studies, develop ment of communication skills, understanding of economic and management principles, ability to assess rock properties that influence extract- ion and beneficiation, and a knowledge of technological developments and limitations are necessary parts of the exploration geologist's

Jan 1, 1974

By S Moradi

The thickener overflow of zinc concentrate, obtained from flotation process in the Angouran plant located in Iran, contains a large quantity of slimes which were transferred to the tailing ponds. These slimes have caused problems of storing and environmental aspects in the Angouran area. The objective of this research is to describe the extraction of zinc from these slimes by leaching method using sulfuric acid in pilot plant scale.Chemical analyses showed that these tailing materials contain 35 per cent of zinc. By XRD analysis, smithsonite is identified as the major constituent. Calcite, dolomite, and cerussite are found as carbonate minerals. A minimal amount of Zn occurs as hemimorphite. Quartz, kaolinite, clinochlore and muscovite are other silicate minerals in the slimes.In the optimal conditions, ie acid leach at pH of 1, temperature of 55¦C, reaction time of 120 minutes and solid-liquid ratio of 1:3 and neutralisation with Ca(OH)2 at pH = 4.5, temperature = 70¦C, time = 90 minutes, the total recovery of zinc obtained was 95 per cent.

Jan 1, 2004

From December 1994 to November 1997 Odin MiningÆs Estero Hondo alluvial gold mine in western Ecuador washed almost 3.2 million bank cubic metres of gravel to produce just over 2600 kilograms of pure gold at a recovered grade of about 0.8 grams per bank cubic metre. The operation was a simple open pit. Draglines stripped the overburden, backhoes mined the gravel, and trucks transported the ore to a stationary, gravity-based wash plant for processing. At start-up the planned throughput was 55 000 bank cubic metres/month, but a year later this had been increased to 100 000 bank cubic metres/month. From April 1993 to July 1997 a total of 440 churn drill holes and 15 pits were sunk to test the property. The methods used to prepare the resource and reserve estimates from the raw field data are described, and seven sets of completed estimates are used to track the evolution of the projectÆs resource/reserve base through the exploration, feasibility and production stages.

Jan 1, 2003

The link between exploration success and new ideas from research and development (R&D), although often assumed, is rarely well explained or well illustrated. One issue is understanding the role of innovative ideas in the exploration process, and another is determining the relative contributing factors to an exploration success. A useful measure of gold exploration success over an extended time period and geographic area is discovery rate (θ): Discovery rate θ = gold discovered/exploration expenditure (usefully expressed as tonnes of gold per $1 million). The total gold discovered is strongly leveraged to discovery rate, as any increase in θ typically has a positive effect on exploration expenditure. Hence, improving the discovery rate is a key driver for a sustainable mineral industry, especially for gold. There are very few ways to influence θ beyond innovative R&D ideas and breakthroughs, and well-motivated and trained staff. The Australian gold industry has experienced exceptional exploration success with 9956 tonnes of gold discovered from 1979 to 2003, inclusive. This equates to: Discovery rate θ = 0.9 t/A$1 M Two-thirds of this gold has been found in the Yilgarn craton of Western Australia (6265 tonnes Au). Without this exploration success, there would have been no platform on which to build the current gold industry and to take advantage of elevated gold prices and advances in mining and processing. Several causes of the Western Australian gold success have been proposed, and more than one may be correct. Gold price, and mining and processing advances have all had influence; but exploration success and discovery of gold were essential to add to the miniscule resource base of 1979. A comparison of the exploration methods used to search for gold in the Yilgarn craton in 1979, and 1990, highlights a small number of breakthrough ideas introduced to the industry during the 1980s, and in most cases emanating directly from local R&D. By the 1990s, these ideas were being used in most gold exploration programs in the Yilgarn craton, and are still used today. These six breakthroughs are: epigenetic timing of gold deposit formation (ie after formation of rock sequence), chemical and mechanical role of host rocks, relevance of carbonate alteration haloes, gold dispersion in the regolith, optimal sampling media, and appreciation of landforms in exploration program design. Interestingly, gold exploration science in Western Australia entered the 1980s period without rigid paradigms in place regarding gold deposit formation; there was a balance between descriptive and genetic models, there was scope to research gold deposits from microscopic to global scales and there were highly effective industry research uptake processes in place: it is suggested here that these favourable conditions contributed to the exploration success and industry growth.

Jan 1, 2007

THE auriferous sulphide ores of the eastern end of Gippsland, and notably of the Cassilis and lVIitta districts, are amongst the most complex and refractory in Victoria-perhaps in Australia. The minerals occurring in these ores are pyrite, arseno-pyrite, zincblende, galena, and (in smaller amounts) some of the copper, sulphides, as chalcopyrite and covellite; and some of the antimonial minerals, notably stibnite and jamiesonite. In the oxidized portions of the lodes, the oxidized lead and iron minerals, and small amounts of the hydrated arseriiate of iron, are found.In the Cassilis mine, near Omeo, copper is present usually in quantities of under 1 %. The magnetic sulphide of iron is of fairly common occurrence. In, the upper levels of the Cassilis mine tin was usually present, the amount going up to 3% in some samples of concentrates. These minerals occur sometimes banded, but usually as an intimate mixture-pyrite and arseno-pyrite predominating. The gangue is usually quartz (blackened by enclosed particles of sulphides). Calcite, magnesium silicate and felspar are also present in varying amounts.

Jan 1, 1911

By S A. Johnson, J Cassidy, J L. Mauk

Geophysical anomalies at Puhipuhi reflect both diverse lithologies and different degrees of hydrothermal alteration. Most significant is a strong negative gravity anomaly (up to 50 g.u.), encompassing but extending beyond areas of known alteration, which is modelled as a deep zone (up to 3 km) of reduced density in the host greywacke basement. This zone, interpreted as being due to alteration (at least in part), closely correlates with the extent of overlying basalt flows. The gravity data indicate that the most intense alteration occurs below the basalts and correlates with the location of previously inferred hydrothermal upflow zones. These observations suggest that the basalt may have acted as a cap rock to a mineralising geothermal system. Aeromagnetic data identify highly variable but typically low magnetisations in the basalts which suggests that alteration may have been contemporaneous with volcanism. These geophysical data at Puhipuhi confirm the locations of centres of known alteration and suggest potential exploration targets below the basalt cap where there is no surface manifestation of alteration. Further implications of these results are discussed in Locke et al. (1999).

Jan 1, 1999

By Sijing Cai, Chengpu Zhou

The requirement of mineral resources is increasing as the economy is continually increasing in China. The mining practices of various complex sulphide deposits and precious metal deposits, and the treatment of mine tailings and other industrial solid wastes, have greatly improved fill quality in the metal mines. From early-1980s, high density slurry fill, paste fill of total tailings, low density slurry fill with addition of silicate gelling agent, etc has been studied and applied, and some progress has been achieved. Today, mine tailings, slag and power plant ash are widely used as fill materials in mining. A number of cemented fill mines equipped with large capacity trackless mining machines are in production. Recently, The 3rd Chinese National Symposium on Mining with Backfill, 1995 has been held, the progress of fill technology in mines has been exchanged and summarised. In the paper, some aspects of fill technology used in the metal mines of China are briefly introduced and some applications of fill research work are presented.

Jan 1, 1998

By Holliday RJ

The Imperial Smelting Furnace (ISF) was developed in Britain during the 1950's as a process which could produce zinc from a blast furnace. Since then it has evolved into an efficient means of producing zinc and lead from lower grade raw materials, both of primary and secondary origin. These changes have been in response to the need to improve the cost competitive position of the ISF in a climate of decreasing metal prices. The improvements at the Cockle Creek smelter of Sulphide Corporation Pty Limited have resulted from work undertaken in four main areas: 1. Changes in plant design and operating practice to give more stable furnace operation. 2. Improvements to the quality of sinter being charged to the furnace. 3. Improved monitoring of process variables and the formulation of control strategies based on the improved data. 4. Increased understanding of the processes occuring within the furnace shaft to allow predictive modelling to be undertaken. Work in these areas is still progressing but the work to date has resulted in a significant improvement in the production rate and efficiency of operation.

Jan 1, 1984

By A S. Kurilko

For mines located in the cryolitic zone, thermal conditions are an important factor for all kinds of mining works, especially for ventilation of workings. In the present paper, some models of mine air heat transfer considering air distribution in a net of mine workings are developed. A combined solution is suggested for heat transfer and air distribution problems in mine workings and other underground structures located in the cryolitic zone. A software package is also presented for calculating temperature conditions in an underground refrigeration plant and for optimisation of ventilation conditions. This software uses a special 3D mathematical model to describe heat transfer in a freezing chamber between surrounding rock massif and stored product as well as between atmospheric air and the daylight surface of rock massif. A problem requiring strengthening of a backfill material and its thermal interaction with surrounding rocks during underground deposit mining by horizontal layers in conditions of the cryolitic zone is also discussed. The developed program takes into account cement consumption, geometrical dimensions of workings filled and a sequence of deposit mining.

Jan 1, 2005

By Houghton BF

Ruapehu is an extremely active andesitic composite volcano, built in at least four cone- building episodes over the last 250 ka. The volcano was constructed by a variety of extrusive and subplinian, strombolian, phreatomagmatic and dome-related explosive eruptions from summit, flank, and satellite vents. The volcano may be subdivided into the cone itself, of volume 110 km3, and a surround- ing epiclastic ring plain of similar size. Four facies associations can be recognised at Ruapehu,-two each on the cone and on the ring plain. Neither cone nor ring plain provides a complete record of the history of the volcano. The cone is dominated by the products of extrusive eruption, as primary pyroclastic deposits are seldom preserved, being rapidly removed by erosion from the steep water- saturated and/or snow-covered flanks of the cone. The ring plain consists of the products of mostly explosive activity forming an alter- nation of primary pyroclastic fall deposits and material transported from the cone by lahars, floods and debris avalanches and then rapidly reworked in sediment-choked hyperconcentrated Streams.

Jan 1, 1987

The precious metallogenic belt and its geoloqical-tectonic location in eastern China.The precious metallogenic belt of eastern China is located in the western part of the Pacific gold metallogenic belt, and occurs in the upper levels of the continent cut by a deep fault structure tending NNE and NE, and active during the Mesozoic. The precious metallogenic period ranges mainly from Late Jurassic to Early Cretaceous (160 Ma-110 Ma); subordinate mineralisation occurred during the Hercynian period, and was rare in the proterozoic.Seven precious metallogenic belts are recognised from east to west, i.e. from continent to the margin active belts, as follows:1. Au-Ag-Te metallogenic belt of East Shandong Province2. Au-Ag-Pb-Zn metallogenic belt of west Liaoning-Miyun area3. Au-Os-Ir-Cr-Cu Mo metallogenic belt of Chengde Pingquan area4. Au-Ag-Pb-Zn metallogenic belt of Zhang Xuan area5. Au-Ag-Pb-Zn metallogenic belt of Zhejiang province6. Au-Ag-Se metallogenic belt of East Qinling area7. Au-Pd-Cu-Mo metallogenic belt of Wansu area

Jan 1, 1990

By Boyack DJ

DEFINING AN ECONOMIC TARGETExploration usually begins with the corporate goal of finding a minimum tonnage and grade of a selected mineral. Sometimes this is expressed more simply as a minimum quantity of contained metal without any indication of the desired grade or implied profitability. Such a goal is useful in the selection of exploration areas and the planning of initial drilling programs. However, it should be reviewed as soon as significant mineralisation has been identified. To make rational decisions about exploration expenditure, the potential return from a deposit must be estimated from the outset and re-esti-mated frequently.The potential return will depend on:1. The proportion of mineral which can be economically recovered from the deposit by mining (the mining recovery).2. The quantity of valuable constituent that can be recovered after dilution with waste rock during mining and losses due to incomplete metallurgical recovery.3. Expectations of price and markets.4. Capital and operating costs applying to the selected mining and processing methods, and to transportation and marketing. Increasingly, environmental costs and constraints must also be considered.

Jan 1, 1990

The Newmont Waihi Operations mill has undergone significant growth over its life. Initially designed as a single SAG mill operation, the circuit has been progressively upgraded since 1988 from a nameplate capacity of 600 000 tonnes per annum to the current rate of 1.3 million tonnes per annum. With future mining potential there is renewed interest to increase the processing rate even further. Over the next twelve months five sustaining capital projects will be undertaken and two major eco-efficiency projects will be completed. With the exception of the large grinding mills, most equipment on a gold treatment plant is replaced after 10-15 years. Waihi Gold mine has been operating for 14 years and has just recently received approval to replace equipment in five main areas; carbon elution, carbon regeneration, scats crushing, intertank screens and variable speed drives. Each project has been justified on improved process efficiencies and operating/maintenance cost savings. The two eco-efficiency projects involve a water balance model and a cyanide optimisation project, both of which are Corporate key performance indicators (KPI).

Jan 1, 2002

By P Hodkiewicz, K Noormohamed

Gold deposits in the Chirano district in south-west Ghana are hosted in a variety of structural settings along the Chirano shear zone (CSZ), in Paleoproterozoic rocks of the Sefwi-Bibiani belt. Most gold mineralisation occurs in strongly sheared and hydrothermally altered Birimian mafic igneous rocks and tonalite intrusions within the CSZ. A recent program of open pit structural mapping, core logging, and three-dimensional modelling helped to define deposit-scale structural controls on gold mineralisation. These include strain domains, shear zone flexures, shear zone intersections and vein arrays associated with host-rock competency contrasts. Interestingly, the plunge of higher-grade shoots in some deposits appears to be associated with the intersection of the CSZ and broadly folded Tarkwaian sedimentary rocks, which are not significant gold hosts in the Chirano district. This paper presents the results of 3D modelling that were used to define structural controls on mineralisation in several open pits and one underground mine along a 9 km length of the CSZ. LeapfrogÖ software was particularly useful because it highlighted the orientations of structural features that focused hydrothermal fluid flow during alteration and mineralisation. The improved understanding of structural controls provided two main benefits: near-mine exploration drill targets and better definition of structural domains for resource estimation.

Jan 1, 2009

More than in any other way, the community judges the minerals industry by its environmental performance. Minerals Council of Australia web site www.minerals.org.au/media/code Time is overtaking us. What was good enough yesterday is not good enough today. What may be acceptable today wonÆt be tomorrow. So we need to leap forward. We need to begin to move towards sustainability. Dick Zandee, Managing Director, Placer Dome Asia Pacific The competition for access to exploration and mining opportunities is intense. So is competition for the best people, capital and community support. Poor environmental performance damages a companyÆs ability to attract these. Quite simply, good environmental management is good business. Hugh M Morgan AO,Chief Executive Officer,WMC Limited. Decisions made by private industry and international corporations are increasingly determining the fate of the environment. ...Nothing could be more shortsighted than for todayÆs conservationists to neglect cooperation with business and industry as a means of moving company philosophy and public accountability ahead in favour of the environment. Dr Claude Martin,Director General,WWF International The four quotes above well illustrate the challenges faced by companies and conservationists in attempting to achieve the societal goal of sustainable development. That this aspirational goal itself is far from clearly defined, although it has been widely accepted and endorsed by governments, business and civil society, exacerbates the challenges. Sustainable development has as its central thesis the integration of environmental, social and economic policy. Its attainment by business has been described John Elkington (1998) as the pursuit of the ætriple bottom lineÆ - the achievement of social and environmental targets, in addition to the traditional economic bottom line. It is self-evident that business is both competent and comfortable defining and measuring economic performance and reporting that performance to internal and external audiences. As long as information has been prepared according to the established standards of measurement and reporting of economic performance, all audiences can have confidence in its accuracy. Business does not enjoy the same competence and comfort with regard to social and environmental performance. This is no startling condemnation of business, any more than it is a criticism of governments, non-government organisations (NGOs) or academia. It is a statement of fact that the tools to allow for credible definition and reporting against the other two components of the ætriple bottom lineÆ have yet to be fully developed and are, therefore, far from being widely accepted. Crucial to achieving sustainability is the ability to measure progress toward the goal. The task is to develop means to define appropriate performance standards and to credibly measure and report company environmental and social performance against those standards.

Jan 1, 2000

In the current climate, there is a real need to bridge the gap between theory and the real world mining considerations, and develop viable, cost-effective, high performance thickeners. With a greater need to extract profits from both difficult-to-process ores and lower grade orebodies, coupled with the necessity to produce 'greener', less water intensive technologies, suppliers need to take current thickener designs to the next level and into the 21st century. The complexity of 'getting it right' within a thickenerÆs feedwell, the 'nerve centre' of the thickener, is no small task. Delivering dilution water and mixing this water with incoming feed slurry, addition of flocculant, maximising flocculant-slurry interaction to build aggregate size, minimising unabsorbed flocculant percentage, volume average of solids volume fraction, momentum dissipation ratio, dilution recycle ratio, volume average shear, maximum shear rate at exit, aggregate size on exit, uniform discharge profile and more ù all of these need to occur in the right order and in the right proportions within the feedwell. This paper discusses the genesis and evolution of a new feedwell design, the first major innovation in the thickening industry in over 15 years.

Jan 1, 2008