Search Documents

WINDING engines are one of the most important units in the equipment of a mine. Upon the winding machinery depends not only the output of the mine, but it supplies in most cases the only means by which workmen enter and return from the mine, and consequently the utmost care and attention is desirable in its design. The efficiency of a direct acting winding engine, as a machine is very low. In other words, the proportion between the useful work performed and the actual work the engine is capable of performing (under the most favourable conditions) is very small. The reasons for this are:-1. The intermittent nature of the work; the engine is stopped from 20 to 25 %(or even more) of the time which would constitute a useful day's work.2. The large amount of power that is absorbed applying the brakes to bring the load to rest.3. That the net useful load raised is small in comparison with dead load to be lifted, and the parts to be set in motion.4. That, owing to the frequent stops, initial condensation in the cylinders is always greater than in a continuously running engine, whilst radiation from steam pipes, valve chests, &c., goes on whether the engine is running or...

Jan 1, 1911

By L Terrusi

The Bungaroo Valley hosts a concealed Tertiary channel iron deposit (CID) along a 17 km stretch of its length. Bungaroo Valley is approximately 0.5 km wide upstream at its easternmost extent, and 3.5 km wide downstream where it joins the Jimmawarrada Creek. The valley follows the axial trace of an anticline that plunges gently to the southeast, and the CID infills the valley. Mineralisation extends to a depth of 230 m below the surface, and almost the entire deposit occurs below the water table. Bungaroo Valley cuts through the Buckland Hills and is bounded to the north and south by steep scarps capped with the resistant Dales Gorge Member of the Brockman Iron Formation. Basement rocks are believed to be mostly Wittenoom Formation shales and dolomites, with Mount McRae Shale and Mount Sylvia Formation also present. Deep, localised depressions appear at the base of the CID sequence towards the north edge of the upstream section of the valley, while downstream the basal CID contact is relatively flat and shallow. In both cases the profile of the CID surface closely mirrors that of the basal contact. The localised depressions seen in the upstream basal CID contact produce significant variations in CID thickness of up to 100 m over short strike distances. This uneven palaeotopography is most likely due to eddying and waterfalls forming within the riverbed prior to CID deposition during a time when the water table was much lower than at present. It may also be associated with possible karsting in an underlying dolomite unit and subsequent syn- or post-depositional collapse of the overlying CID. The irregular basal contact of the Bungaroo CID sequence has implications for mining in terms of pit design and resource accessibility.

Jan 1, 2007

By Das S. C

A detailed study was undertaken on the effect of Fe+3 in combination with LIX64N during copper electrowinning from sulphate electrolytes. The results show that the presence of Fe+3 not only affects the current efficiency during copper electrowinning but also affects the cathode quality. The effect is enhanced by electrolysis parameters like temperature, circulation rate, current density, etc. No significant effect was found from the presence of Fe+2. The presence of Fe+3 along with LIX64N causes a synergistic effect and results in a drastic fall in current efficiency. Moreover, cathode quality is also affected. A pyramidal structure is favoured in the presence of Fe+3 but the presence of LIX64N along with Fe+3 promotes a ridge structure. Addition of thiourea not only causes modification of cathode deposits, but also a rise in current Efficiency.

Jan 1, 1992

By Savidis GM

This report outlines the experience of Australian mining operators in dealing with large falls of roof in advance of longwall supports. Previous and present techniques used for face stabilisation have been described, together with an analysis of [actors which contributed to the roof falls, in each case. Attention has been focused on the stabilisation technique used at Angus Place Colliery, where the face coal was successfully reinforced by injecting chemical foam into Lite fractured areas. Although considered to be one of the worst roof falls in the history of Australian longwalls (60 m in length and up to 10 in in height), it was subsequently possible to resume cutting in Longwall 9 two weeks after the foam injection. A preliminary schedule of work involving the 'strata replacement' method, is also discussed. It has been based substantially on experience gained with cementitious supports, principally by ACIRL and Monier Resources.

Jan 1, 1986

By M McGeough

Following the success of calcrete sampling at Challenger, calcrete sampling has been widely adopted as the primary exploration technique for gold exploration, in the Gawler Craton. Calcrete is uniformly distributed over large areas and produces discrete gold anomalies. This allows drilling to focus on specific gold anomalous targets. However, despite widespread use of calcrete sampling, very little is known of the origin of calcrete in the Gawler Craton, and the link between calcrete gold anomalies and primary mineralisation. In an attempt to understand this association Lisa Gibbons recently completed an honours project at the Old Well Prospect approximately 45 km SSE of Tarcoola. Her work is part of a collaboration between CRCLEME, MESA and MIM Exploration. At Old Well, a calcrete anomaly (>10 ppb Au)covers an area approximately 7 km x 2 km with a peak value of 97 ppb Au. The study looked at the regolith as a whole, processes of its formation and nature of mineralisation within it. She was able to combine previous calcrete and drilling results with her own observations. The results from this study highlighted problems in relating surface calcrete anomalies to in situ gold mineralisation.

Jan 1, 1998

Gold at Renco occurs in association with pyrite, pyrrhotite, chalcopyrite and quartz and is confined to a series of brittle fractures and fault breccias (reefs) preferentially developed within an anastomosing ductile shear zone. During late Archaean crustal movements both the orebody and the enclosing host rocks were deformed within a series of east-north-east striking, southerly dipping, shear zones. The reefs within these shear zones are now texturally different to those away from the shear zones, and this difference is reflected by differences in the way the gold is distributed in the two reef types. These differences are not taken irto account by the software package currently being used to generate kriged plans of gold grade and reef thickness and this may explain some of the inaccuracies found in these plans.

Jan 1, 1990

Controlled Source Audio Magnetotelluric (CSAMT) surveys were carried out by Glass Earth (New Zealand) Limited (Glass Earth) in 2006 - 2007 to investigate epithermal gold targets in the central North Island of New Zealand. The surveys were conducted using a Zonge GDP 32 8-channels receiver and a Zonge XMT 32 transmitter powered by a 16 KW generator. The electric field dipole was maintained at 20 m length (five dipoles per 100 m spread) and the frequency ranged from 4 KHz to 4 Hz. Only scalar (TM mode) signals were recorded, using one magnetic coil per spread. The transmitter bipoles were 1 - 4 km in length and located about 5 to 10 km from each survey area.   Sixteen individual target areas were surveyed by June 2007. The CSAMT survey lines (100 - 400 m spacing) were determined mainly on results from previous ultra-detailed airborne magnetic and gravity surveys conducted by Glass Earth in 2005. The data from each CSAMT line was carefully examined to remove any spurious signals and processed using Zonge SCS2D software, which can produce smooth 2D resistivity inversions of the field data. The results were presented as resistivity sections and maps to help the identification of exploratory drilling targets, mainly from the existence of subsurface high resistivity zones (resistors) that can be interpreted as caused by silicification associated with epithermal mineralization.   An example of processing and interpretation of the CSAMT data is presented in this paper on results from Glass EarthÆs Tahunaatara target, where CSAMT surveys have identified zones of epithermal mineralization confirmed by exploratory drilling.

Jan 1, 2007

DURING the four years, 1922, 1923, 1924, and 1925, China produced the following quantities of non-ferrous metals and ores: Antimony Products - 67,869 (long) tons. The production for 1925 was 20,869 tons, of which 80% was regulus, 14% crude,and 6% oxide.Arsenic (White) - 4200 tons. The production for 1925 was 1200 tons, but only 90 tons were exported, some 25% of which to Hong-Kong, France, and U.S.A. each, and the rest in small lots to other countries. Domestic consumption was 1110 tons, and thelocal price for "cake" was around £47 per ton on 1925 exchange.Arsenic Ore (Realgar) - 1400 tons.Lead Ore (Galena) - 44,853 tons. The production for 1925 was 10,853 tons, of which 16%, produced in Korea, went to Japan, and 84% produced in Hunan, went to Europe.Manganese Ore (Pyrolusite) - 142,567 tons. The production for 1925 was 42,567 tons, of which 94.3% went to Japan.Tin Ingot - 33,480 tons. In 1925 the exports to Hong-Kong were 8880 tons of usual rough tin of 94% to 96%. Most of this was refined to No. I Chinese quality of 99.3% and exported to U.S.A. and Europe, owing to the good price ruling.Sulphur - 12,000 tons. Sulphur is included in this list in order to explain how its production led to the discovery of some other ores.Wolfram - 19,668 tons. The production in 1925 was 5868 tons, most of which came from the Quee Mee mountain district in South Kiangsi, from the detrital deposits. Civil disturbances prevented the usual output from Hunan border.Zinc Ore (Blende) - 134,190 tons. Exports for 1925 were 34,190 tons of low-grade ore, averaging 30% zinc, 14% lead, and 7% silver...

Jan 1, 1927

Gold is actively precipitating at grades up to 80 g/tonne at and near the surface of the Waiotapu geothermal system, located in the Taupo Volcanic Zone of New Zealand. Many characteristics of this active system makes it analogous to the environment deduced for epithermal precious metal mineralisation in the circum Pacific region.The near surface area of the geothermal system is approximately 17 km2, caused to an extent by the upflow of deep, neutral pH fluids being deflected into a lateral flow of several km. This fluid has pervasively altered the rhyolite pyroclastic and ash deposits to an assemblage generally characterised by the term propylitic; major vein mineralisation is not observed. The temperatures at the 1100 m limit of drilling are 300¦C, and decrease to the surface along a boiling point curve.Condensation of steam and H S (subsequently oxidised) at the surface (derived 2from deep boiling) results in the formation of heated acid sulphate waters. These have caused a shallow (50 m) cap of advanced argillic alteration. Mixing of this oxidised condensate with the deep neutral pH fluid appears to be the principle cause of gold deposition from thiosulphide complexes. The major focus of gold mineralisation is in Champagne Pool, a hot spring which fills one of several 900 year old hydrothermal eruption craters.

Jan 1, 1984

By R R. Anand

Recent research by CRC LEME from an Australian mineral exploration perspective, has focussed on regolith architecture and mechanisms of geochemical anomaly formation, within transported regolith. Methods have been developed for the rapid production of regolith-landform maps which is the starting point for understanding regolith architecture in the third dimension. Methods for development of 3D regolith models are less well advanced, and require integration of all available geological and geophysical datasets, but still with a heavy reliance on drill-hole information. The base of the transported regolith û the unconformity û remains the most important regolith boundary for geochemical sampling in transported regolith terrains. A new generation portable spectral logger, employing a broader spectrum can interpret important features from drill chips within the regolith. This allows internal architecture, redox fronts and the all-important interface to be objectively identified. Transported lateritic components can provide vectors to mineralisation in depositional regimes. Palaeomagnetic and new radiometric methods which date individual phases of the regolith provide evidence of different episodes, each characterised by different geochemical dispersion patterns in transported regolith. Along with lateritic residuum, calcrete is prime sampling medium. Calcrete is probably enriched in gold through physical and biological processes, rather than straight chemical processes. In South Australia, the lowermost calcrete layer buried within the depositional regime, especially where it lies directly over the silcrete layer at the buried interface, is the desired sampling medium. Certain gum trees, with deep roots in transported regolith have been shown to record anomalous values of gold and basemetals in leaves, twigs and bark. Anomalous metals in acid-sulfate soil seeps can also provide a window through sedimentary cover in respect of mineralisation in the basement. A number of Yilgarn occurrences of gold anomalies in transported cover, strongly infer hydromorphic and biological mobilisation of gold. This inference is supported by micro-analyses of regolith mineral hosts in hardpans and mottled sediments, which show gold and pathfinder elements prefer to reside in goethite and specific types of clay minerals. This creates anomalies in specific mineral phases. However the inference that that these are sites of mobile or labile metal ions remains enigmatic. Similarly there is inconclusive evidence that selective extractions will provide an anomaly not otherwise detected by conventional total dissolution methods. Hydrogeochemistry is a promising exploration tool for basemetal exploration. The importance of microbes in both the dissolution and precipitation of gold in the Australian regolith is demonstrated. We are on the verge of identifying the functional gene sequence of individual active microbes. A consideration of possible mechanisms for creating anomalies in soils above transported regolith, presents difficulties in facilitating upward movement of ions from the watertable to the surface. Perhaps the best avenues of research lies with surrogate soil gases, and biotic transfers.

Jan 1, 2004

The continued exploration of the major brown coal deposits of the Latrobe Valley has resulted not only in the discovery of huge additional reserves, but also in new concepts of the stratigraphy and structure of the coal seams in that area. The author sets out his interpretation of the new information which has become available over the last six years.A section of the paper is devoted to the quality of the coal. As the chemical composition of these brown coals has been discussed in some detail by previous authors, only the major constituents and the heat value of the coal are dealt with in this paper. Some of the variations in quality are related to the geological structure.The occurrence of underground water and its relation to open cuts is dealt with briefly.INTRODUCTIONThe Latrobe Valley Tertiary Basin is almost entirely covered by a layer of Post Tertiary sediments which mask the underlying rocks and their structures. As a result, the geological understanding of this area has had to await the comprehensive drilling campaign in search of brown coal, initiated by the Victorian Mines Department in 1917, and subsequently carried on by the State Electricity Commission of Victoria. The first detailed geology was published by Herman (1922), and this was followed some 25 years later by papers by Edwards, and later Thomas and Baragwanath, to which reference will be made later in this paper. Herman included a section on the geology of the Latrobe Valley in his book Brown Coal, which was published in 1952.Since that time a considerable amount of new information has become available from the continued drilling carried out by the Commission. In addition, geophysical work carried out by the Commonwealth Bureau of Mineral Resources has assisted in the defining of geological structures in the area.

Jan 1, 1960

By Wilson R. G

The Bulli and Wongawilli Seams, the two principal sources of coking coal for the Port KKembla steelworks of Australian Iron and Steel Pty. Ltd., vary in rank and in type over the Southern and -South Western Coalfields. The Bulli Seam, ranging widely in type, produces coke varying from weak to strong. The Wongawilli Seam, more consistent in type, produces coke of more consistent strength, but considerably less strong than that from the best Bulli Seam coal. Plans of seam variation show the regional trends in rank and type for each sear. The strongest coke is derived from coal containing between 45 and 55 per cent vitrinite, m.m.f. This is obtainable from the Bulli Sean in a zone embracing Bulli and Appin Colleries.

Jan 1, 1969

By A B. Richards

Effective control of blast vibration and flyrock requires that significant factors be identified and quantified, that the blast be designed to ensure both blasting efficiency and compliance with applicable limits, and that the blast design be effectively implemented by field personnel. Significant factors contributing to ground vibration and airblast are: charge mass; distance and direction relative to the blast; drilling design: burden, spacing; stemming height and material type; hole diameter and depth; and initiation sequence and direction.In addition, airblast may be strongly influenced by shielding and meteorological conditions. Ground vibration is also influenced by the transmission characteristics of the ground and soil. Flyrock throw is determined by charge mass, burden, stemming height, blasthole diameter and depth. The contribution of each of the factors has been quantified and models developed to enable the environmental outcomes of blast design to be predicted. Environmental blast design is necessary to ensure compliance with regulatory limits and the implementation of æsafeÆ exclusion zones for flyrock clearance. This paper discusses the models used for environmental blast design and demonstrates the often significant effects that lapse during implementation of the design can have on predicted outcomes. In practice, drillers and shotfirers are sometimes confronted with situations that require modifications to the blast design to cope with the real site situation. Methods are presented that may be used by drillers and shotfirers to evaluate the effect of these modifications, the tolerances that must be reached during their work practice and checking procedures, and the consequences of their actions.

Jan 1, 2004

By Liu Q, Siefken T. C, Misra V. N

Investigation of the differential flotation characteristics between arsenopyrite and pyrite in a ore concentrate have been carried out on a laboratory Leeds flotation cell. Experimental results indicate that some limited separation between arsenopyrite and pyrite is possible by differential flotation under the conditions of high pH and low pulp redox potential. The best performance in this testwork was achieved by using an oxidizing agent at pH 10.7. Of the oxidizing agents tested, NaOCI gave better oxidizing effect than KMnO4. It has also been observed that the pulp redox potential depends on the pulp pH value. At high pH values a hydroxide layer is formed on the arsenopyrite surface, which has the effect of a depressant on the arsenopyrite.

Jan 1, 1992

This paper introduces a new, safer bulk emulsion loading system for underground mining operations. The features and benefits of the equipment, along with the use of Dyno Nobel Inc patented gassed emulsion technology, is summarised in the application of a stope blast with very difficult and complex ground conditions. The paper describes methods used to optimise the amount of energy required to break the ore while protecting the integrity of the surrounding backfilled pillar.

Jan 1, 2004

Roof bolting with resin bonded bolts has been developed extensively in French coal mines. There are three aspects of this development: 1. The reason for and the care used in the development of roof bolting from use as a reinforcement in a classical arched roadway to use as the only support in roadways in ad- vance of the working face (the roadway being reinforced behind the face); 2. The problems encountered and studied, such as choice of boltable roadways and determination of the technical data in designing a roof bolting pattern; 3. Only because roof bolting has been controlled by safety rules, and especially by accurate measurement of strata behaviour, has this system of support been expanded aapidly in France since 1967.

Jan 1, 1971

By F J. van Zyl, C A. S Thomson

"Anglo American Thermal Coal conducted a high level study of all of its underground collieriesto determine if there were electrical power saving opportunities at the main fan stations.A systems approach to electrical power savings was used to identify potential savings in the various components of a primary ventilation system. Furthermore, only technological interventions were considered to obtain electrical power savings. From generic technological driven electrical power saving strategies four energy savings strategies were identifi ed, namely potential overall reduction in ventilation volume, improved underground air utilisation, optimisation of fan-set effi ciency and potential fan drift design optimisation. The study indicated the colliery (say Colliery D, Shaft A) that showed most potential in the four technology driven energy savings strategies. A detail study was undertaken at Colliery D, Shaft A to increase the confi dence level and the study confi rmed that up to 45 per cent of the main fan absorbed power can be saved (475 kW) with an estimated capital payback period of 18 months. The study clearly showed that an integrated approach to optimise the entire mine ventilation system has great potential for power saving, and that a clear, well -defi ned methodology will be applicable to similar underground collieries. This paper discusses the background to the study and the process followed to implement the energy savings initiative at Colliery D, Shaft A."

Jun 1, 2012

Before presentIng my address I wish to acknowledge the honour which has been conferred on me by my appointment to the position of President of the Australasian Institute of Mining and Metallurgy.It is a matter of great concern to us all to find our Empire at war. I am confident that, as was the case in the war of 1914-1918, members of this Institute and of kindred Institutes and Associations will contribute in full to the Empire's needs and that in the end our cause shall triumph.I think it appropriate that I should take as the subject of my address that of the Broken Hill Lead-Silver-Zinc Industry. The subject matter of this address has been confined to the operations of Mining, Ore Dressing, Lead Smelting and Refining and production of Electrolytic Zinc in Australasia. The review of the Broken Hill Lead-SilverZinc Industry would not, of course, be complete without reference to those Australian industries which trace their origin to the Broken Hill field, but· it is thought that an outline of these industries would make thIs review too extensive.HISTORICALMany efforts have been made to translate the early history of Broken Hill and its subsequent growth throughout the years into one of the wor~d's most famous mining fields in the form of a simple story.

Jan 1, 1940

By Schiller J. C, Both R. A

Base metal mineralisation occurs at several locations within the regionally metamorphosed Kanmantoo Group on the southeastern flank of the Mount Lofty Ranges between Kanmantoo and Strathalbyn, 50 km southeast of Adelaide. Sulphide mineralisation is of three main types (Seccombe et al, 1985):1. copper deposits, at the Kanmantoo and Bremer mines, South Hill prospect and several minor occurrences,2. lead-zinc deposits at Aclare, Wheal Ellen, Strathalbyn, St. Ives, Scott's Creek, and Glenalbyn mines,3. pyrite-pyrrhotite mineralisation of the Nairne pyrite deposit and many other pyritic schist units within the Kanmantoo Group.Syntheses of folding, metamorphism and stratigraphy of the Kanmantoo Group were given by Kleeman and Skinner (1958), Offler (1960, 1963), Offler and Fleming (1968), Marlow (1975), Mancktelow (1979) and Parker (1986). Studies of the general relationships of mineralisation to structure in the Kanmantoo area were given by Grasso and McManus (1954), Mirams (1962), Poole (1969), and Lindqvist (1969).Several conflicting views on the origin of mineralisation in the Kanmantoo Group have been proposed. Thomson (1975) considered much of the mineralisation as a late-stage product of regional metamorphism and he, like Parker (1986) and Lambert et al (1987), stressed the importance of major lineaments as an ore control. However, Lindqvist (1969) and Verwoerd and Cleghorn (1975) tentatively suggested a syn-sedimentary origin to the Kanmantoo copper deposit and Jensen and Whittle (1969) and Seccombe et al. (1985) on the basis of sulphur isotope data proposed a bacteriogenic sulphur source and a sedimentary origin for sulphides in the Nairne pyrite deposit. The latter suggested that most copper deposits represent stockwork, vein or disseminated zones within subsurface vents whereas massive mineralisation at Wheal Ellen and Aclare mines probably accumulated on the ocean floor.This paper presents new geological information on the structural and metamorphic setting of the base metal deposits and attemptsto relate this information to previous regional studies of the Kanmantoo Group. Estimates of pressure and temperatureof peak metamorphic conditions based on silicate mineral stabilities are considered in relation to various silicate and sulphidegeothermometers which have not previously been applied to rocks in the Kanmantoo Group.

Jan 1, 1988

By J Ortiz

In almost all copper mining companies, mine planning is done considering different time frames, leading to long-term (life-of-mine) (LOM), medium-term (first three years) and short-term (first year, monthly, weekly, and up to daily plans). Shorter term plans are usually associated with more abundant information, hence models with lower uncertainty. However, they capture more of the variability found on the geological attributes. In long-term models, usually estimation methods tend to hide this variability, providing smoothed interpretations.Medium and long-term plans consider average values for the parameters and optimisation techniques are applied aimed at maximising the economic profit. Short-term plans, on the other hand, are made to comply with the medium-term promises, maximising the use of the available resources (equipment and processing capacities) and dealing with the variability not characterised in the previous planning stages. This generates an important gap between the short-term and the medium and long-term plans. A case study was made using an important oxide copper mine, where the variability found in the short-term plan has a large impact in the productive process, thus reducing the daily ore grade variability is an important goal. In this paper, this planning issue is addressed by creating medium-term mine plans using mixed integer programming which are compared using the output of a simulation of the daily extraction that is aimed at satisfying the daily constraints of the processing plant, the availability of mining equipment and the variability of ore grade. The result shows the expected gap between these mine planning processes, which suggests correcting some of the parameters used in future medium and long-term plans.

Sep 26, 2011