Search Documents

By Matthew SP, Hayes PC

The product morphologies formed on the reduction of dense wustite crystals are classified into three types,A) porous iron, B) porous wustite covered with dense iron and C) dense wustite covered with dense iron. The mechanisms of formation of these structures and the effects of impurity elements on the product morphologies are discussed

Jan 1, 1984

Queensland hosts vast deposits of brown and black coal, significant accumulations ranging in age from Permian to early Tertiary. The great diversity of coal resources in the State to some extent reflects the proximity of Queensland to plate-marginal tectonic processes through much of the Phanerozoic eon. Coal is contained within sedimentary basin fills of four fundamental types; 1. extensional, 2. foreland, 3. strike-slip, and 4. intracratonic. Thick (10 m+) though laterally restricted coal bodies are characteristic of extensional and strike-slip basins, whereas coals of more modest thickness but much greater lateral extent are typical of foreland and intracratonic basins.

Jan 1, 1991

The physical phenomena which influence gas flow in the bosh and hearth of a blast furnace are discussed including the hold-up of slag as a mechanism which can result in a flooding condition. An equation is defined which describes the limitation to wind volume arising from the flooding condition. Implications of the various factors influencing bosh and hearth gas flow on furnace operation are discussed. Coke quality is shown to be the most important factor in the aerodynamics of these zones and coke requirements are defined for the Port Kembla No. 5 BF which has an inner volume of 2670 m3.

Jan 1, 1975

The thick coal seams of the South Maitland field are the only ones in New South Wales which have been worked extensively to heights beyond 3.8 m (nominal "thin" seam height). Under shallow cover only minor difficulties were experienced in developing first workings but later the widespread occurrence of incidents of spontaneous combustion and the growth of "creeps" extending over large areas gave the field its own peculiar problems. As the mines have driven under deeper cover extreme difficulties in forming development roadways have been experi- enced. Various methods have been adopted in an attempt to overcome the problems of the field.

Jan 1, 1976

By Freeman NV

The concept of an in stream analysis probe was developed at The Zinc Corporation (now Z.C. Mines) in the late 1960's and commercialised quite rapidly, by Phillips and then AMDEL, as an alternative to the established centralised systems (Courier, etc.). The developments which have taken place since that time are reviewed and current procedures and performance are described. An audit of the system, recently undertaken by AMDEL, has highlighted areas where improvements can be made. In 1988 the ISA system will become an integral part of a substantially upgraded process control system.

Jan 1, 1988

The Barra Mine was the most significant mine of Australia's earliest mining era, which took place in South Australia between 1841 and 1851, the decade prior to discovery of gold in eastern Australia. Between 1845 and 1860, Barra was the largest metalliferous mine in Australia and employed up to 1000 men and boys, most of them Cornish.""Today the site is also important in a physical and archaeological sense as it contains extensive remains of mining and processing operations of the period 1850 - 70. Most significant are three cnginchouses which housed Cornish beam engines.

Jan 1, 1993

By G MacDonald, B Forsyth, D Corkery, T

An investigation was carried out at Diavik Diamond Mines Inc (DDMI) to identify and quantify the mechanisms through which ammonium nitrate (AN) was entering the mine discharge water. The goal was to develop and complete an investigation of the potential AN loss mechanisms in order to assess their contribution to ammonia in the mine water system. The initial phase of the project involved the collection and analysis of blasting and water quality data that were used to determine the mechanisms by which the ammonia enters the mine water system and to establish a baseline data set for comparison with results from future trials designed to reduce AN loss. Three potential options for reducing AN loss were identified through the first phase of the project. The second phase of the project involved conducting a series of monitored trials with changes made to the drilling and blasting process. The results of these trials were compared to the baseline data set to determine if the changes introduced for the trials had reduced AN losses while producing satisfactory blast results. This paper describes the process for the collection of the baseline data, provides an analysis of the resulting data, discusses the changes made to blasting operations in order to minimise AN loss and describes the results observed subsequent to these changes.

Jan 1, 2007

By Yambu J, Titus K

Geotechnical investictations and monitoring have been integral to development of the Porgera Gold Mine. The steep, unstable terrain has required a program for monitoring of slopes and foundations which includes survey stations, borehole inclinometers and piezometers. Case studies of the Maip Pass landslide, Yakatabari land-slide, Anawe Plant Site CIP pond excavation and batter, and a load test study for mine waste dumps are presented.Monitoring is needed to ensure that geotechnical risk is kept to a minimum. A vigilant program will be required for the life of the mine.

Jan 1, 1994

By M Behrens, A McPhee, B D. Hegan

This paper describes the design and construction of twin 400 m long road tunnels as part of the Northern Motorway Extension Project in Auckland, New Zealand. Construction of the tunnel civil works is now completed and installation of mechanical and electrical systems is well underway. The tunnels are expected to be open for traffic at the end of 2008. The paper will address the design aspects of the project including: tunnel alignment and cross-section, geotechnical conditions and rock support, waterproofing and concrete lining and fire and life safety. The paper will cover the bored tunnel section, the cut-and-cover tunnel section, cross passages and portal structures. The design brief included a requirement for the tunnels to be a gateway to Auckland and this required particular attention to be given to the visual appearance of the finished tunnel structure. The final arrangement of the portal structures and a requirement for recesses in the concrete lining for emergency cabinets, deluge pipework and cable runs, reflects these requirements. The tunnels were excavated by a roadheader and road planer using a heading and bench. Initial support was provided by a combination of lattice girders, cement grouted rock bolts and steel fibre reinforced shotcrete. The permanent lining consisted of installation of a drainage geotextile and waterproof membrane, followed by cast in situ unreinforced concrete. Each portal consists of a cut-and-cover section. This paper describes the tunnel construction methods, including the particular requirements for safety, the environment and community relations. The tunnel is fitted with a compartmentalised deluge system for fire fighting purposes. The tunnel control centre is incorporated into the control centre for Auckland Harbour Bridge, some 30 km from the tunnel location.

Jan 1, 2008

Depletion of shallow ore reserves is forcing the South African gold mining industry to exploit reefs at ever-increasing depths. By 2010 around 30 per cent of South African gold production probably will come from depths greater than 3 km (Johnson and Schweitzer, 1996). At such depths, virgin stresses will rise significantly, producing complex rock engineering problems (Malan and Basson, 1998). Concern over structural instability at depth has led planners to seek a technology capable of ædetection of geological structures with a displacement of 2 m or greater (or as appropriate to the mining technique) 200 m ahead of mining at an acceptable costÆ. Borehole radar probably is such a technology. Cover holes are drilled routinely ahead of development. The evaluation of its candidacy for a tactical role in ultra-deep gold mining dependsùamong other thingsùupon establishing the electromagnetic characteristics of the environment hosting significant gold reefs. The Ventersdorp Contact Reef (VCR) is one such reef. Recent borehole radar field trials, presented here, suggest that the VCRÆs overburden is a remarkably translucent, clutter-free dielectric with a Q of ~35 and that the VCR itself is the dominant radar reflector.

Jan 1, 2002

At Hilton Mine, 18 kilometres north of Mount Isa, the silver-lead-zinc sulphide bodies have undergone strong deformation in the form of folding and later faulting and brecciation in the hangingwall region of the mine. Variation in grades and widths over compara- tively short distances causes problems regarding accurate sampling of orebody exposures in underground development, and in defining confidence limits for the extrapolation of ore intersections in ore reserve calculations. The paper gives a preliminary insight into the problem of obtaining representative samples for exposed orebodies and discusses the sampling techniques employed. Results gained from these sampling methods could not be verified due to lack of individual bulk samples for comparison but strong evidence for precision was provided. INTRODUCTION In a developing mine like Hilton, accurate grade information is of extreme importance. Original grade information for a potentially viable ore deposit is gained from surface drilling, and initial ore estimates are calculated from the resultant ore widths and grades. After underground development has proceeded, the opportunity arises for detailed examination of orebody exposures, and the resultant assay grades and widths from sampling of these exposures may, in the long term,

Jan 1, 1976

By Pinczewski WV, Nowak LP, Tanzil WBU, Jenkins DR, McCarthy MJ

An experimental and theoretical study has been made of the drainage behaviour of two-dimensional packed beds drained from an outlet in the sidewall of the bed in order to identify the fundamental me- chanisms involved. Under these conditions a grad- ient develops in the air-liquid interface in the direction of flow with the interface tilting towards the outlet. This results in a significant volume of liquid being retained in the packing on completion of draining when the interface first reaches the bed outlet. Residual liquid volume and the shape of the air-liquid interface as a function of time were det- ermined experimentally in a two-dimensional packed bed where the packing consisted of glass spheres ranging in size from 0.6 to 10 mm dia. and the bed was drained at superficial liquid velocities rang- ing from 0.007 to 0.32cm/s. The test liquids used were water, glycerine/water solutions and kerosene resulting in a viscosity range of 1 to 10 mPa.s and a surface tension range of 0.0243 to 0.072 N/m. Assuming laminar flow within the bed, a compu- tational model was developed to predict both the liquid residual ratio and the temporal evolution of the drainage profile within the bed. The computed results were in good agreement with the experimental data over the entire range of conditions invest- igated. the computational model was used to estimate the relative importance of the effects of changes in hearth conditions on residual slag volume for typ- ical blast furnace operating conditions. On the basis of the computed results it is concluded that coke quality is a major parameter affecting hearth drainage performance.

Jan 1, 1981

By M A. Mular, T Akroyd

A fundamental model, which considers the subprocesses of particle collection by bubbles in flotation, is applied to two comprehensive flotation surveys in the rougher stages of C3 concentrator, PT Freeport Indonesia. The flotation surveys focused on the collection of: cell-by-cell and size-by-size metallurgical, cell hydrodynamic, and pulp and surface chemistry information.The two surveys were conducted at significantly different feed tonnages, giving rise to significantly different feed particle size distributions, pulp densities and mean pulp residence times. A series of model simulations are performed with the aim of quantifying changes in copper recovery, on both a size-by-size and unsized basis, with changes in values of the hydrodynamic parameters and hydrophobicity of the copper sulfide mineral. This was carried out in an effort to identify the most promising route to increase overall copper recovery in roughing. It was found that by increasing the hydrophobicity of the copper sulfide mineral surfaces it became possible to optimise cell hydrodynamics, which targeted increased fine (-12 ¦m) copper sulfide mineral recovery but without adversely affecting coarse (+150 ¦m) copper sulfide mineral recovery.

Jan 1, 2007

By Hayward N, Sutherland D, Wilkie G

A pilot plant study has been made of the liberation characteristics of a nickel ore under different milling conditions. A series of runs were made ranging from fully autogenous grinding to semi-autogenous grinding with a ball load of 8%. The mill products were sized and assayed then analysed by QEM4SEM. This enabled a full liberation analysis to be carried out to see whether the autogenous grinding leads to improved liberation by promoting selective breakage. Though it is frequently claimed that fully autogenous grinding yields superior liberation this could not be detected in the present study.

Jan 1, 1991

By M Fishwick Tapia

This paper was prepared and translated from the final report of the investigation into the Codelco Chile Salvador DivisionÆs air blast which occurred in the Inca-West area. In this section of the block cave mine, a stable arch formed covering an area of approximately 15 000 m2 . This zone subsequently collapsed producing a massive air blast. The collapse followed a series of planned extraction activities and occurred on 5 December 1999. This paper discusses the cave back arching event and the measures that were taken in order to induce the controlled collapse. This was to minimise risk to personnel, equipment and installations. The results obtained to date are presented.

Jan 1, 2000

By Carr SD

The Omineca Belt of the Canadian Cordillera straddles the western boundary of the North American paleocontinental margin and accreted oceanic and island arc terranes. Crustal thickening of the orogenic belt was initiated in the Jurassic and culminated in latest Cretaceous and Paleocene times.Thin-skinned shortening of the Rocky Mountain Foreland Thrust and Fold Belt was balanced by basement-involved crustal imbrication within the Omineca (hinterland) Belt. Middle and upper crustal rocks of the hinterland (Selkirk allochthon) were thrust eastward and ramped onto basement of the North American continental margin. By latest Paleocene the southern Omineca Belt formed an elevated crustal welt that was at least 60 km thick.Within less than 3 Ma of the culmination of crustal thickening the belt was rapidly uplifted and tectonically denuded. The southern Omineca Belt was extended by as much as 80% as upper crustal rocks were displaced on moderate to low angle normal sense shear zones and brittle normal faults. This oro-genic collapse is interpreted to be a gravitational response to crustal thickening and thermal soft-ening, facilitated by reduction in plate-boundary-induced far field stresses.

Jan 1, 1990

Knowledge of coalfield geology has evolved rapidly over the past few years. Recent advances ranging between exploration, mining geology and seam variation studies have enabled application of geological techniques commensurate with technological changes in the coal industry.

Jan 1, 1969

By G M. Hoffmann

Utilisation of lower grade (Jigging technology has progressed to a point where SishenÆs 50 to 60 per cent Fe run of mine (ROM) material, once considered as waste, can be beneficiated to produce a saleable 64 per cent Fe product. This has been confirmed through appropriate beneficiation testwork. Consequently, Sishen can now produce saleable product from material not currently included in the resource definition, significantly increasing the resource base of the mine and ensuring higher resource utilisation. Mine planning utilised the geological models to produce detailed planning schedules, reflecting the current and SEP plants separately, optimised to comply with product specifications of both the current and SEP plants and to confirm the viability of the low-grade resources identified as SEP feed material. The SEP product specifications have been derived by optimally matching iron ore market requirements with the revised resource base. A 64.0 per cent Fe lump product and a 63.5 per cent Fe fine product are the optimal SEP products. The SEP plant will be able to produce 10 Mtpa at an average yield of 60 per cent and a lump to fine ratio of 62:38. The plant consists of five major sections: namely crushing, material preparation, beneficiation, final product handling and quality control services. Maximum integration with the current Sishen plant was considered. Kumba currently has an agreement with Transnet to rail up to 23.5 Mtpa through the Sishen Saldanha iron ore export channel (IOEC). Transnet and Sishen Iron Ore Company have signed a Definitive Agreement that deals with the expansion of IOECÆs capacity, which increases KumbaÆs entitlement from 23.5 Mtpa to 35.0 Mtpa. The detailed enviro-legal impact assessments for the SEP indicated that the project has low enviro-legal risk as a result of it being a brownfields project incorporated into the current Sishen operations.

Jan 1, 2005

The grade (or value) to volume relationship which constitutes a target orebody is used to show that the concentration of diamonds in an economic deposit may be as low as O.Olg/t. Diamond valuations from an Indonesian deposit demonstrate that the largest 5% of the diamonds in the deposit contributed 25% of the mass of diamonds recovered and 70% of the value from the ore. The need to consider the large stone content and the probability of recovery is used to estimate that the sampling density is required to be as high as 4-10,000ppm for a VLC deposit. This is compared with an acceptable sampling density for a bauxite deposit of 700ppb. A case history of the discovery of a diamond bearing paleo-channel in the Ellendale field in Western Australia illustrates that the sampling task becomes impractical. It requires an excavation in excess of 300,000 bcm of material to prove a 5M hem ore reserve. The conclusion is reached that setting up a small scale mining operation is an appropriate method of proving such an ore reserve and that the Code of Reporting should allow a category of "Mineable Resource" to cover such a situation.

Jan 1, 1990

By P W. Cleary, G K. Robinson, M D. Sinnott

Discrete element modelling (DEM) is a research tool that involves numerically solving the equations of motion of large numbers of particles. It can be very useful for investigating mechanisms that can lead to bias when extracting samples from material as it is carried on a conveyor belt or as it falls from the end of a conveyor belt. DEM is more realistic than conceptual models and mathematical models; but it is not as realistic as physical experimentation. Its primary advantages over physical experimentation are that it is cheaper and that it allows many factors to be varied while keeping other factors unchanged.This paper reviews our investigations of the performance of sampling systems by using DEM. The sampling systems investigated include falling-stream cutters, cross-belt cutters, Vezins and a device called a ætrue-beltÆ cutter, which is being developed. The purpose of the review is to explain what DEM has contributed to the theory and practice of sampling, and to indicate what it is likely to be able to contribute in the future.CITATION:Robinson, G K, Cleary, P W and Sinnott, M D, 2012. How discrete element modelling is influencing the theory and practice of sampling, in Proceedings Sampling 2012 , pp 15-20 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012