Search Documents

By M Ogle

"Booster fans are relatively rare in Australian coal mines. However, as mines become progressivelydeeper it is likely that such fans will be increasingly adopted as a method to sustain or improve the ventilation of underground workings. The reasons why booster fans may be an att ractive alternative include: increased cost of sinking additional ventilation shafts with greater seam depths; environmental objections to shaft sinking projects; and increasing urbanisation and surface constraints limiting availability of potential ventilation shaft sites. As Tahmoor Colliery movedinto its northern lease the ventilation constraints became the limiting factor on production. Thelimitations of the old workings meant that the existing ventilation system would be inadequateto sustain the required production. Extensive ventilation modelling was carried out to evaluatevarious potential solutions and the recommended option was the installation of a booster fanor fans, to gain underground access to an already approved shaft site in the northern lease.Proposals were sought from recognised fan manufacturers and various alternative arrangements were tendered. Ultimately the choice was between one large centrifugal fan and a set (three or four) of smaller æauxiliary-likeÆ fans in parallel. The successful tender was for a single centrifugal, an arrangement very similar to the booster fans that have been operating eff ectively at Westcliff Colliery for a number of years. This paper describes the current ventilation network, evaluation of the ventilation options, the fan selection process, and the project status to date."

Jun 1, 2012

By J A. Sanchidrián

The general ranges of validity of some distribution functions are assessed from their behaviour with 119 sets of fragmentation data from bench blasting obtained by sieving. The emphasis is on determining the lower size/passing limit that the size-scaled Rosin-Rammler, Grady and Swebrec functions, and their bi-component versions, can represent with reasonable precision. By fitting these functions to the data using different weights, the accuracy of the fit varies in the different size/passing zones, so that an overall knowledge of the capacity of the function is obtained across the whole size range, from the coarse zone to the fines. Reasonable ranges of use of bimodal Rosin-Rammler and extended Swebrec (all of them five-parameter, bi-component distributions) are, in terms of percentage passing p, 99 > p > 2 per cent (up to 100 per cent for the extended Swebrec), or 90 > p > 0.5 per cent, in which the expected error of the calculated size is below 15 per cent in the extremes of the range, and less than five per cent in most of the central range; maximum errors (ie errors that will only rarely be exceeded) are typically less than 50 per cent in the central range, and up to about 100 per cent in the extremes. Ranges of use for the Swebrec and the size-scaled Rosin-Rammler (three-parameter distributions), with only slightly larger errors than the bi-components, are 100 > p > 5 per cent or 80 > p > 2 per cent. The classical two-parameter Rosin-Rammler can be used in the range 95 > p > 20 per cent or 90 > p > 10 per cent, with expected and maximum errors less than about 15 per cent and 100 per cent respectively.CITATION:Sanchidrián, J A, 2015. Ranges of validity of some distribution functions for blast-fragmented rock, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 741–748 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

DCF Valuations are very important to individuals and companies involved in the mining industry. Such valuations are critical to investment decisions in relation to new and existing projects. In particular they provide fundamental information to shareholders in the event of a capital raising or takeover and to financiers supporting mining companies and projects. Also, DCF Valuations are often used to support asset carrying values in the financial statements of mining companies. This paper presents a Chartered Accountant's (CA's) perspective on the main issues to be considered in preparing, analysing and relying upon DCF methods in mineral valuations and provides some practical examples relating to key issues. The paper makes the important point that DCF methods involve making assumptions about future events and circumstances that inherently contain uncertainty which results in a valuation prepared on a DCF basis providing a range of values that are not perfect or accurate. In order that DCF valuations provide meaningful information the underlying methodology used and assumptions made must be consistent, sound and well supported. Credibility of those involved in preparing mineral valuations is vital and this paper supports the adoption of sound practices by all concerned.

Jan 1, 1994

By G W. Wilson

Net solar radiation is one of the key factors affecting evaporation from soil covers on waste rock dumps. While net solar radiation is normally taken as a uniform parameter over a site for modelling purposes, there can be significant variation in the radiation actually received on various portions of the dump. These variations are a function of the difference in the cover slope and direction of exposure. A predictive model has been developed to calculate the actual radiation received on the dump surfaces, based on the net radiation data measured at a weather station on a horizontal surface. The model has been designed for application at any mine site in the world, and can be used in conjunction with evaporative flux models to help estimate the effect of three-dimensional variations in the cover surface exposure. The waste rock dump at Equity Silver site (located in British Columbia, Canada) has a barrier-type soil cover system to limit oxygen entry and water infiltration. This cover has been monitored for the past nine years. The new net solar radiation model has been applied to this site and the predicted net radiation was compared to the values of actual net radiation measured on the site. The predicted variations in net radiation over the three-dimensional surface of the waste rock dump have been applied to calculate spatial variations in potential and actual evaporation (or evapotranspiration) from the site. Preliminary analyses indicate actual evaporation from a site at this latitude could vary by a factor of two for exposed versus shaded slopes. The implications of these variations for the site are considered.

Jan 1, 2003

By M J. Pascoe

The performance of 460 stope surfaces at WMC ResourcesÆ Olympic Dam Operation (ODO) has been used to investigate the confidence that can be placed in the Stability Graph Method for design of stope dimensions. A detailed database of stope performance and ground condition information was established for each stope. The database contains all the required stability graph information as well as other factors thought to influence stability, such as discrete major structures, poor shape and exposure time. The performance of each stope surface was quantified by calculating Equivalent Linear Overbreak/Slough (ELOS). The performance of stope walls and crowns was plotted on the supported and unsupported case history stability graphs. Based on this information an ODO design limit of HR = 3.3 x NÆ0.33 has been suggested for stope walls. Walls that plotted above this line were 80 per cent stable, 20 per cent unstable and zero per cent failed. Below the line 60 per cent were stable, 30 per cent unstable and ten per cent failed. Supported crowns that are flat or arched in shape and are not within the influence of major structures can be designed in the stability graphÆs æstable zoneÆ with a strong likelihood of stability. The Stability Graph Method did not reliably predict the performance of unsupported crowns at ODO.

Jan 1, 2005

By J R. Kyle

The Deep Mill Level Zone (DMLZ) skarn Cu-Au deposit is the deepest explored part of the Ertsberg East Skarn System extending from the surface at 4200 m elevation to the DMLZ at 2900 to 2600 m. The DMLZ is hosted in an upper Cretaceous to lower Tertiary siliciclastic and carbonate succession adjacent to the 3 Ma Ertsberg pluton. Much of the DMLZ ore is hosted by mixed assemblages of siliciclastic and dolomitised carbonate strata that have been altered to Mg-rich skarn assemblages. Unaltered equivalent strata from a 300 m cored interval in the Yellow Valley Syncline were characterised petrographically and representative samples were analysed for major element compositions. These stratigraphic and chemical units are interpreted to be responsible for the varying skarn lithologies within the DMLZ. The dominant prograde skarn assemblages are controlled by protolith composition, notably the relative abundance of quartz, dolomite, and calcite within the protolith. Models based on isochemical metamorphism of mixed assemblages of quartz and dolomite suggest that the formation of the forsterite-diopside dominant skarn assemblages resulted in the greatest amount of pore space increase. DMLZ Cu-Au concentrations were locally controlled by host lithology, with structural features providing fluid pathways that focused the mineralising fluids. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By A Hall, D Kratochvil, P Littlejohn

Economic recovery of gold from complex gold ores, including poly-metallic deposits, is impacted by the presence of cyanide-soluble base metals. These base metals can create both a metallurgical challenge plus waste handling and disposal challenges. Base metals such as Cu and Zn compete for the cyanide reagent and often increase the total cyanide consumption to the point of making precious metals recovery uneconomic. In addition, the accumulation of base metals in cyanide solutions represent a challenge for cyanide detoxification and waste water treatment as these metals report to waste sludge. Such sludge requires safe handling and disposal, with possible long-term liabilities.Base metal interference can be removed with sulfidisation-acidification-recycling-thickening (SART) process technology. SART liberates the base metal from the cyanide complex and precipitates the metal as an insoluble sulfide product that can be recovered as a commercial grade concentrate. With the base metal precipitated, the cyanide can be regenerated as free cyanide and recycled to the gold extraction circuit.BioteQ completed laboratory testing for two projects, one employing cyanide leaching of copper-gold sulfide flotation concentrate and one employing a Merrill Crowe process, to determine the effectiveness of SART to remove and recover Cu and Zn in high-grade sulfide concentrates and to reduce the impact of cyanide-soluble metals on gold recovery and cyanide consumption. This paper will provide an overview of the testing methodology and results along with a review of the potential for SART to be applied to complex gold ores with poly-metallic deposits to improve project economics, operability and waste management.CITATION:Littlejohn, P, Kratochvil, D and Hall, A, 2013. Sulfidisation-acidification-recycling-thickening (SART) for complex gold ores, in Proceedings World Gold 2013 , pp 149-156 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By L L. Kuhar

The AMIRA International P843A Geometallurgical Mapping and Mine Modelling (GeMIII) project is an interdisciplinary research collaboration between 17 global mineral companies and four research organisations aimed at providing support for the emerging industry trend of geometallurgy. The main aim of the project is to develop predictive geometallurgical indices which can be incorporated into a resource block model to maximise the commercial value of an orebody and to minimise the social and environmental impact of mining operations.Researchers at the Parker Centre/CSIRO have been focusing on the development of predictive hydrometallurgical indices for the GeMIII project via rapid, small-scale, cost-effective tests and protocols for comparative ranking of attributes relevant to leach performance. The focus of the small-scale leach tests has been to determine the leach index (relative indication of leach performance), recovery, impurity deportment, reagent consumption, effect of size/degree of liberation and mineralogy of samples for their relative ranking. Predictive tests for heap leach hydrology (related to agglomerate characteristics) and slurry rheological behaviour are also being developed.

Sep 5, 2011

By Koeng R, Richardson M, Hoare R

A discrete event computer simulation model was developed for two of the stoping methods currently used at the Z.C. Mines Broken Hill oper- ations. The objective in undertaking this project was to provide an effective tool for mine planning and design to allow comparisons of alternative extraction strategies and attempt to optimise the allocation of capital equipment and human resources. The Slam II simulation program was used in conjunction with ,a com- monly used data editor, text editor and graphics package to allow the simulation to be done on a personal computer with minimum training requirements. The computer hardware used was a portable computer cur- rently available using 80386/20MHz electronics. Specific logic techniques were developed to allow the Slam II language to simulate mining opera- tions because it was originally developed for manufacturing and com- mercial simulations. The design of the model was based on observations and a data collec- tion campaign. The model was designed with flexibility which allows simple editing of the input data which includes: - Insitu volumes - Development statistics -Loadout efficiencies -Loader speeds, availabilities and capacities -Chute numbers, volumes, distances and blockage statistics -Trucking statistics -Work schedules -Utility statistics

Jan 1, 1988

By James JV, Petho SZ

The South Deep surface shaft system is being sunk to a final depth of 2750 in below surface and on completion will be the deepest single drop haft in the world. The shafts will intersect the target reef horizon at 2650 to below surface. In order to negate the requirement for a shaft pillar, which would he extremely large at this depth, the reef horizon in the vicinity of the intersection is currently being mined. A high quality crushed waste/classified tailings backfill is being placed in the longwall stoping panels around the shaft intersection area. This kill limit closure and ride which following shaft reef intersection could have a detrimental effect on the long term shaft stability. This paper discusses underground instrumentation results and numerical modelling exercises carried out to confirm that the shaft system will he stable throughout the life of the mine. Instrumentation projects include closure and ride measured between backfill paddocks and haulage leveling exercises carried out to determine the far field rockmass response to mining with stiff backfill.

Jan 1, 1998

The results from three quick methods for the determination of W03 in scheelite ore samples, mill products and concentrates were compared with gravimetric results and tested with standard samples to establish which was the most reliable. Summaries of the methods, two X-Ray fluorescence and one colorimetric, are given. The best method was X-Ray fluorescence, with samples cast as glass discs.

Jan 1, 1988

By Jaques A. L, Heinrich C. A

Mt Todd lies towards the south end of the Pine Creek Geosyncline, sandwiched between the Cullen Batholith and the Edith Falls Basin, in an area of regionally metamorphosed sandstones, siltstones and shales. The Batman deposit, some 3 km west of Mt Todd is a sheeted quartz vein system hosted within greywackes of the Palaeoproterozoic Burrell Creek Formation (Finniss River Group). The gold-bearing quartz veins, trending 010¦-020¦ and dipping 60¦-70¦E, are commonly 0.5 to 5 cm wide and occur at intervals which are from 10 cm to 1 m apart. Gold tends to be restricted to the quartz veinlets and immediately adjacent country rock. Grade Control utilises two 4 m 'collar' samples which are collected from each 8 m production blasthole. The irregular distribution of the quartz veins and erratic gold mineralisation has resulted in a disseminated 'salt and pepper' type of gold occurrence, with only a poorly defined footwall. Delineation of ore and waste blocks for mining uses an approach which combines the smoothing effect of kriging with a pragmatic view of the raw data. Large ore blocks with simple geometry help to minimise mining dilution, reduce block variance and give good reconciliations to interpreted ore tonnes and grade. Daily mine face advance is reported against truck counts and provides continual comparison with budgeted production. All data processing uses Gemcom software, together with Lotus spreadsheets.

Jan 1, 1994

By S Jahanshahi

In an earlier LCA study, the authors showed that the electricity consumption of the electric furnaces used in the production of the ferronickel and ferrochrome feedstocks made significant contributions towards the Gross Energy Requirement (GER) of stainless steel production, on a æcradle-to-gateÆ basis. Given the relatively low efficiencies associated with electrical power generation, substantial reductions in the GER for stainless steel production could be anticipated if more direct use of thermal energy was made in the ferronickel and ferrochromium smelting stages.In view of these findings, a follow-up study was undertaken to investigate the likely environmental benefits of using bath smelting processes for the production of ferronickel and ferrochromium compared to the traditional rotary kiln-electric furnace processes, but still utilising the electric furnace process for stainless steel production. The METSIM process simulation software package was used to set up models of the two bath smelting processes and provide process energy requirements that were incorporated into the LCA. The environmental impacts considered in the LCA were greenhouse (Global Warming Potential, GWP) and acid rain gas (Acidification Potential, AP) emissions and solid waste emissions.The results of the study showed that the bath smelting route reduced the GER for ferronickel production by about 37 per cent over the traditional route, which translated to about a 21 per cent reduction in the GER for stainless steel. The corresponding reduction for ferrochromium was about half that for ferronickel, and when combined with the ferronickel result gave a 25 per cent reduction in the GER for stainless steel production. Similar reductions were also observed for the GWP and to a lesser extent the AP for both feedstocks, as all primary energy inputs were essentially fossil fuel based. Substantial reductions in solid waste emissions were also indicated for the direct use of ores in smelting. By utilising bath smelting processes for the production of the ferronickel and ferrochromium feedstocks, stainless steelÆs suitability for meeting many of the goals necessary for sustainable development, already recognised because of its particular properties, would be even further enhanced.

Jan 1, 2004

By X Li, M-F Zhou

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Yinachang deposit in south-west China contains large amounts of Fe, Cu and rare earth elements (REEs). Apatite in this deposit records complex REE mineralisation and remobilisation processes.Fe-Cu-(REE) mineralisation at Yinachang occurred at ~1700 Ma, and three stages of alteration and mineralisation are identified: Na-(Fe) alteration, Fe-(REE) mineralisation and Cu-(REE) mineralisation. In the Fe-(REE) mineralisation stage, REE-rich apatite formed together with magnetite. In the Cu-(REE) mineralisation stage, fluids undersaturated with REEs interacted with early-formed REE-rich apatite, during which large proportions of REEs, especially light REEs (LREEs), were leached from apatite.At ~840 Ma, apatite experienced a second interaction with fluid. In that process, REEs were removed from the apatite structure but immediately reprecipitated into new phases within the apatite. Thus, numerous REE mineral inclusions including bastnaesite, monazite and minor Y-phosphate occur in the apatite. There are also a very small portion of LREEs that were transported out of the apatite, resulting in the growth of bastnaesite and monazite grains outside the apatite.This study demonstrates that REEs can be mobilised in multistage hydrothermal activities and highlights the significance of fluid compositions for REE transportation and deposition behaviours in hydrothermal systems.CITATION:Li, X and Zhou, M-F, 2015. Hydrothermal rare earth element mobilisation processes in the Yinachang Fe-Cu-(REE) deposit, south-west China, in Proceedings PACRIM 2015 Congress, pp 265–270 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Revy T

A testwork program aimed to improve the assaying of underground face samples established that for an Accelerated Cyanidation Extraction using the LeachWELLTM 60X catalyst, followed by an Aqua Regia finish (to quantify non-cyanide-extractable gold): ò Assay results (including the aqua regia finish) from a full set of samples from one underground face can be returned within four hours. ò The reagent dose to make the method simple and 'bullet-proof' is 8 gm LeachWELLTM 60X and 20 gm NaCN per 200 gm sample (30 per cent solids). Pulverising is to 90 per cent passing 75 micron (compared to the standard of 90 per cent passing 150 micron), and cyanidation is completed within one hour - however both might be further optimised. ò The LeachWELLTM/Aqua Regia results demonstrate that Fire Assays suffer from a significant nugget effect which makes the Fire Assay data relatively unreliable. ò Original costs, specific to Bannockburn (viz including an Aqua Regia finish), handling approximately 20 000 to 25 000 per annum is estimated to be $5.40, ie about one-third less than fire assaying. Optimising is further reducing these costs. It is estimated that the LeachWELLT"'/Aqua Regia assay procedure has reduced the probable error limits of any given assay of this ore from the range 0.74x to 1.36x for Fire Assay, to an appreciably smaller range of 0.90x to 1.11x. Thus for a cut-off grade of 1.60 g Au/t, samples with Fire Assays ranging up to 2.18 g Au/t have 25 per cent chance of being below cut-off, while samples with Fire Assays as low as 1.18 g Au/t have an equal chance of actually exceeding cut-off grade. This 1 g Au/t range in uncertainty is generally unacceptable for many practicalgrade/tonnage relationships. By contrast, using LeachWELLTM + Aqua Regia assays, the estimated corresponding limits are 1.44 g Au/t and 1.78 g Auk respectively - a far more tolerable 0.34 g Au/t range of uncertainty. Subsequent data has demonstrated that sufficient accuracy for grade control is achieved by Accelerated Cyanidation alone, further halving the cost of assays.

Jan 1, 1994

By Y Ren

The algorithms employed by the commercial tools are either heuristic algorithm or iterative optimisation of a subsystem. This often results in a suboptimal schedule. In this paper, the author presents a new scheduling algorithm that incorporates with a novel stockpile configuration system, an improved algorithm on multiple processes and a mixed-integer linear programming (MILP) global optimisation model. It can simultaneously optimise stockpiles, blending, multiple processes as well as multiple mines. In addition, it allows the user to interact with the solution to adjust the solution to be practical and desirable.CITATION:Ren, Y, 2013. A simultaneous optimisation tool for open pit mine scheduling, in Proceedings World Gold 2013 , pp 427-432 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By G Le Juge, K Waldock

The current suite of bulk mining explosives has been available to the industry for over 20 years. The flexibility and performance of ammonium nitrate based emulsion blend explosives were accepted by the mining industry in the early 1980s. These water resistant explosives rapidly displaced the water gels and slurries developed during the previous two decades. However, since the 1980s there has been no equivalent step change to the basic formulation or application of bulk explosives, although there has been a continuous process of refinement with respect to stability, handling characteristics and most significantly, cost. In the 1980s explosives supply contracts were awarded based on technical evaluations, usually accompanied by field trials. Technical personnel from both mining companies and explosives suppliers dominated the negotiations and there was a strong focus on explosive energy and blasting requirements. Today, explosives from alternative suppliers are difficult to differentiate on the basis of energy so the focus has shifted to aspects of service and price û bulk mining explosives are now largely treated as a commodity and the negotiations are dominated by commercial personnel. Commercial pressures from large mining companies have seen a substantial reduction in the real price of explosives. However, this has come at a cost. In order to reduce manufacturing costs, emulsion formulations have changed. In general they are not only cheaper, but also less energetic. Powder factors have had to increase to achieve the same blasting results, especially in hard ground. It is debatable whether the mining companies have achieved all of the economies they were seeking. This paper discusses these issues and argues that the mining industry would benefit from taking a more technically driven approach to meeting their blasting requirements. Recent trends towards more open contracts between the mining companies and their suppliers can be extended to explosives. To achieve this, mining companies will need to acquire sufficient technical knowledge to take a more pro-active approach to specify the characteristics of the explosives required to maximise the economic performance of their operations.

Jan 1, 2004

By Polthier K

A short discussion of the salient aspects of a dispersed flow model in relation to the gas flow in blast furnaces is given. The use of the theory in assessing vessel performance is mentioned. Tracer results of a blast furnace (688 m3) from three furnace levels and different radial positions are analysed and results presented as D/ud values. The significance of the shapes of experimental tracer curves are included and comparison is made with results obtained on other furnaces.

Jan 1, 1975

By S T. L Harrison, J-P Franzidis, M Becker, N Dyantyi, J L. Broadhurst

Gold mining is a major contributor to the South African economy, but is associated with several environmental issues such as acid rock drainage (ARD). ARD is due to the oxidation of sulfides in gold tailings and is characterised by low pH, high sulfate content and elevated concentrations of heavy metals that contaminates scarce water resources and subsequently limits the use of such waters without treatment. Treatment strategies can only be implemented if the acid-generating potential of mine wastes is effectively predicted using common static and kinetic acid prediction tests. The choice of test performed is usually a trade-off between the number of samples, speed of the test, cost of the analysis and level of information obtained. Often the results of these various tests are not consistent with one another. This study uses mineralogy to analyse biokinetic test results of a Witwatersrand gold sample in order to improve the understanding of behaviour of mine wastes under different ARD prediction test conditions.All ARD prediction testing methods investigated in this study showed that the gold sample is considered to be potentially acid forming with net acid generation (NAG) pH of 2.5 and net acid producing potential (NAPP) of 36 kg H2SO4/t. Results of biokinetic test showed that ANC was consumed within four days confirming acid producing potential of the sample with low neutralising potential as observed from acid base accounting (ABA) (4.7 kg H2SO4/t) and mineralogy (4.9 kg H2SO4/t). Results generated in this study demonstrated importance of mineralogy in both understanding the controlling reaction mechanisms playing key role in ARD formation and its capability as a prediction technique. Future work will focus on the application of mineralogy in interpreting the behaviour of mine waste under different static test conditions with a view to assessing their applicability and reliability in estimating potential acid generating characteristics of gold tailings.CITATION:Dyantyi, N, Becker, M, Broadhurst, J L, Harrison, S T L and Franzidis, J-P, 2013. Use of mineralogy to interpret laboratory-scale acid rock drainage prediction tests - a gold case study, in Proceedings World Gold 2013, pp 519-526 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By L Stitz, S Kinnear, L D. Fabbro

Sensitive and tolerant species of macroinvertebrates were present across a wide range of conductivity concentrations in the Isaac River catchment in Central Queensland, indicating the need for further ecological studies in the field to underpin the development of regionally-tailored guidelines for conductivity. The Isaac catchment has naturally high conductivity, but there is also increasing pressure on resource companies to ameliorate saline mine water discharge. Recently, catchment management efforts have included a revision of the water quality guidelines that are specific for the broader Fitzroy catchment. These guidelines include the use of macroinvertebrates as indicators of ecosystem health, but developing and applying such guidelines first requires a good understanding of macroinvertebrate ecology and population dynamics, ideally from field validation. To date, studies of macroinvertebrate tolerance to conductivity in southern freshwaters, as well as in laboratory-based ecotoxicological tests conducted in Queensland, have suggested that ranges exceeding 1000 ¦S/cm are likely to have negative impacts on survivorship of all taxa. However, these results may not be transferable to natural populations of macroinvertebrates from the Isaac, where the naturally high-conductivity water may allow the opportunity for adaptation. To test this, macroinvertebrate assemblages were examined at a series of sites in the upper Isaac River catchment at the end of the dry season in 2012. Patterns in the assemblages were examined together with water quality parameters, in order to gauge the ability of macroinvertebrates to survive at conductivity concentrations exceeding 1000 ¦S/cm. The specific conductance of the field sites ranged from 477 ¦S/cm to 9791 ¦S/cm and a total of 39 families from 13 orders were identified. Species richness was not significantly different between sites of differing conductivity. Macroinvertebrate populations were dominated by Dipterans as well as the traditionally more pollution-sensitive families Ephemeroptera and Trichoptera. There was an absence of any correlation between conductivity and species richness (P > 0.050), suggesting that macroinvertebrate taxa richness occurs independently of conductivity, at least in this particular cohort of mining and/or grazing influenced ephemeral systems in Central Queensland.CITATION:Stitz, L, Fabbro, L D and Kinnear, S, 2013. Macroinvertebrate tolerance across a range of conductivities in the Isaac River Catchment (Central Queensland), in Proceedings Water in Mining 2013 , pp 135-142 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013