Search Documents

By E R. Ramanaidou, M A. Wells

Reflectance spectroscopy is now an established technique for mineral exploration and ore characterisation. The efficacy of the technique as a tool to characterise the main iron ore and gangue mineralogy at African Minerals Ltd’s Simbili iron ore deposit in north-central Sierra Leone was tested through reflectance spectroscopic analysis of 13 000 pulped drill reserve samples using CSIRO’s HyLogger-1™ system. Specifically, integration of reflectance spectral data with more traditional methods of analysis, such as geochemical analysis and Satmagan measurements, characterised the mineralogy (ie hematite versus goethite) of the oxidised ore at Simbili, quantified the Al associated with goethite and hematite and evaluated the distribution of the main gangue minerals – kaolinite and gibbsite. Relative changes in the Fe2+/Fe3+-bearing oxide and silicate mineralogy, based on mineral indices derived from reflectance spectroscopic measurements, appeared well-related to changes in the ore profile mineralogy consistent with the main ore types identified at Simbili, as representative of an oxidised banded iron formation sequence. Spectral calibration models, developed from a well-characterised training set of mineral mixtures, representative of the oxidised ore zone mineralogy were used to quantify the distribution of Al associated with kaolinite and gibbsite and the iron oxides, goethite and hematite. Combining these mineral spectral parameters with compositional data enabled the differentiation of Al-substituted goethite and hematite and resulted in the identification of low Al-bearing, or ‘clean’, goethite and hematite from high Al-bearing, or ‘dirty’, goethite and hematite. Spectral quantification of the iron oxide Al composition provides a far more rapid means of quantifying the Al substitution in iron oxides at the deposit scale compared to traditional techniques such as X-ray diffraction analysis. It also enables a level of volumetric characterisation and the potential for large-scale (ie three-dimensional) mapping, which was not previously possible with other techniques. The potential of the technique was also highlighted when mapping the distribution of the main Al-bearing contaminants (gibbsite and kaolinite) identified in the oxidised ore zone at Simbili. Delineation of such zones provides a guide to managing the most appropriate processing options (ie upgrade potential) within a mineralogical framework. Three-dimensional modelling of the gangue phase distribution may also allow the mapping of lithological and/or structural controls that may be prevalent at Simbili. This work highlights the value in the application of HyLogging™ technology for rapid resource characterisation, particularly for volumetric identification and mapping the distribution of both the economic and gangue phases, which otherwise would be difficult to achieve. As such, the technique can provide a fast and inexpensive means to evaluate ore and gangue mineralogy at the deposit scale and provide a first-pass assessment of the mineralogy and compositional attributes, with the potential to better predict ore metallurgical properties.CITATION:Wells, M A and Ramanaidou, E R, 2015. Waste not, want not – delving deeper into the Simbili iron ore deposit using HyLogging™ scanning technology, in Proceedings Iron Ore 2015, pp 337–346 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By G Cavanough, A Olsson, J Rock, A C. Torrance

There are various methods currently in use to determine detonation performance of bulk explosive products including velocity of detonation (VOD), high speed photographic analysis, fragmentation analysis and unconfined detonation of samples. For assessment prior to detonation the current practice is limited to a measurement of cup density. This paper presents additional techniques that have been developed to provide measurement and assessment of bulk explosive products. Techniques applicable prior to detonation include a mobile laboratory to allow on-site chemical and physical analysis of sensitised products and ‘in-hole density’ measurement to monitor the in-hole density during sleep time. Assessment of detonation performance is achieved using detonation pressure sensors. These sensors allow measurement of detonation pressure, average VOD, propagation time and magnitude of the pressure induced in the explosive column by detonation of adjacent blastholes.CITATION:Cavanough, G, Torrance, A C, Rock, J and Olsson, A, 2015. Measurement and assessment of bulk explosive products, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 477–484 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By C Samuelsson, Q Shu, A Lennartsson, F Gyakwaa, A Andersson, J Isaksson

The physico-chemical property, viscosity, is essential for pyrometallurgical processes and influences the settling rate of valuable metal droplets in slag, affecting the metal recovery. The copper slag from smelting furnaces typically contains between 1 and 2 wt per cent Cu, which equals to or is higher than in most sulfidic copper ores mined today, meaning the slag is a valuable resource for copper extraction. A low viscosity is desirable for slag-cleaning through a settling furnace where entrained droplets settle under gravity. One approach to control the viscosity is through the slag composition. The literature has limited data on the correlation between viscosity, slag structure, and optical basicity of iron silicate slag with FeO/SiO2, CaO, and Al2O3 as factors. Therefore, the present study evaluated the influence of these factors on viscosity and correlations with slag structure and optical basicity. The FeO/SiO2 ratio (at%/at%) and the CaO and Al2O3 content were altered in two levels, resulting in a two-level full factorial design with three factors. The study was done by synthesising FeO–SiO2–Al2O3–CaO–MgO–Cr2O3 melts, followed by water granulation. The melt structure of the samples was analysed with the help of Raman Spectroscopy. The viscosity was then estimated with a high-temperature rheometer using a Mo spindle and crucible. The results showed a correlation between the optical basicity, FeO/SiO2 ratio, and viscosity, where a high optical basicity and FeO/SiO2 ratio were beneficial for achieving a low melt viscosity.

Jun 19, 2024

By K P. Tully

In August 1996 a Microseismic Monitoring System developed by ISS International Limited was installed at the Pasminco Broken Hill Mine -Southern Cross area. The project aims were to:Assist in daily safety management in a mine environment which exhibits one of the highest occurrences of microseismic activity recorded in the Australian mining industry. Be used as a proactive tool in design of future development and stoping. The project to-date has been an unqualified success in achieving both goals. Consequently the system is being expanded from 6 to 14 monitoring sites.

Jan 1, 1998

By B Wu, B W. Lei, B J. Duan

When a coalmine fire occurs, it is crucial to judge the developing trends inside the fire area by analysing the changes of gas concentration in order to formulate the proper rescue measures. At present, few researchers have focused on the relationship between the changing trend of gas product and basic characteristics of fire in the coal fire extinguishing process. To study the relationship of basic characteristics of coalmine fire during the extinguishing process, an experimental platform for coal combustion in a confined space was built, and gas production, flame image and coal temperature during the extinguishing process were monitored and analysed by an online continuous gas analysis instrument, camera and thermocouple. Research shows that during the burning phase of the coal sample in the confined space, the flame zone decreases gradually due to insufficient gas supply. The size of the flame zone fluctuates and shares a positive correlation with CO concentration, while sharing a negative correlation with O2 and CO2 concentrations. Then, in the extinguishing phase, the increasing rate of CO2 concentration and the decreasing rate of O2 concentration both decrease gradually, but CO concentration would rise for a period before it eventually decreases. Coal temperature continues to rise in the open flame stage and does not go down until the flame is extinguished.CITATION:Lei, B W, Wu, B and Duan, B J, 2015. Experimental study on extinguishing characteristics of coal fire in confined space, in Proceedings The Australian Mine Ventilation Conference, pp 279–284 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

The JORC Code contains a mandatory classification system for Mineral Resource and Ore Reserve estimates for public reporting. The classification is a statement of the Competent PersonÆs confidence in the estimate and an attempt to convey that confidence to the various users of the resource estimate. In general the classification process is either largely subjective, relying on the Competent PersonÆs experience, or relies on statistical measures derived from the estimation process, or is derived from an estimated level of confidence in the outcome. However, the statistical measures may not necessarily relate to the overall confidence in the resource or reserve which must take account of the confidence in the geological inputs to the estimation.In addition to the traditional deterministic interpretation and estimations adopted by geologists, semi-quantitative techniques are now available to improve the estimation of confidence while continuing to involve the Competent PersonÆs experience in the process. Methods for quantifying confidence in mineral resource estimates for advanced projects and operating mines have also been developed.Classification is undertaken primarily as a communication tool between the estimators and the other stakeholders in the process. A brief examination of the stakeholdersÆ requirements is included.

Sep 26, 2011

By W N. Qin, B Zhang, W Z. Huang, X S Mo

Mengzi Mining and Metallurgy Co, Ltd (MMMC) polymetallic ore contains recoverable amounts of tin, lead, zinc, pyrite and other valuable minerals. With the change in orebody, the run-of-mine (ROM) ore changed from lead zinc rich ore to tin rich ore, where the current ROM ore contains 0.45–1.25 per cent tin, 20–25 per cent sulfur, and 0.20–0.35 per cent copper. The previous processing flow sheet was designed to recover lead zinc rich ore and it is clearly not suitable for recovery of the current tin rich ore, where the tin was already overground and tin recovery was only 50.19 per cent. The Mengzi Mining Company has recently modified the concentrator circuit by incorporating rod mill and high efficient Derrick fine screen. As a result of the improved classification efficiency, the overgrinding of the tin ore was minimised and the recovery of tin was improved by 20.71 per cent, ie from 50.19–70.90 per cent. An additional $10 M revenue per annum can be achieved as a result of the modification.CITATION:Qin, W N, Huang, W Z, Mo, X S, Zhang, B and Wheeler, J, 2014. Application of high efficient fine screen to improve the recovery of tin concentrate, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 487–492 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By R J. Longbottom

In this study the bonding within reduced titanomagnetite-coal compacts was investigated. The aim of the study was to better understand the binding mechanisms in the reduced compacts and, based on this understanding, to improve on their strength.Titanomagnetite ore was combined with sub-bituminous coal to form compacts. The compacts were then reduced by heating in a thermogravimetric furnace (TGA) to temperatures between 1000 - 1300°C under argon. The reaction progress was monitored by measuring the weight loss with time. The reduced compacts were found to have low strength in compression testing. The main form of bonding between the reduced titanomagnetite particles in the compact was by the formation of a slag-like material. Increasing the fi nal reduction temperature was found to have a profound effect on the strength of the compacts by promoting the formation of this slag-like material.Attempts to improve the strength of the compacts were made by changing two variables, the type of coal and the addition of rice husks. The addition of coking coal gave reacted samples that had little strength, while the addition of rice husks may have enhanced the strength of the reduced compacts.

Jul 11, 2011

By P Thompson, B W. Atkinson

Water treatment is not æcore businessÆ for mining companies.Just as mineral ores and coals are unique, each requiring detailed characterisation and pilot-testing to determine their optimum beneficiation route, so too are mine waters, each requiring careful assessment to determine the most appropriate treatment. There are many cases of æregret capitalÆ expenditure, whereby mines have installed off-the-shelf equipment only to find it inadequate for their purposes or grossly expensive and labour intensive to operate.Water may be required for potable purposes, ore processing, dust control and/or irrigation. A major driver will frequently be environmental constraints for off-site discharge. Mine water projects can become very complex, and detailed models need to be prepared and optimised to properly consider the raw water sources, the on-site storages, the on-site uses and the off-site discharges, as well as handling the residuals (by-products) of water treatment. By-products may be in the form of concentrated backwash streams or streams of elevated salt content. Careful management of the by-products is required to avoid recontamination of the source water.Regulators often drive mine owners toward reverse osmosis (RO) so that their discharges can be considered as æzero dischargeÆ in terms of potential pollutants. Such decisions need to be based on site-specific information rather than any form of æblanketÆ requirement. An analogy is that many humans like to consume mineral water rather than ænormalÆ tap water. Receiving environments also accommodate or even prefer their æmineralsÆ and so RO is neither warranted nor sustainable in many cases.This paper presents two case studies for operating mine sites, both of which have a significant excess of water requiring environmental discharge. The examples demonstrate a sensible balance between treatment type, environmental constraints, process implementation and residuals management. LIMN« æthe flow sheet processorÆ was used to model one of the case studies due to the complexity of the water system on that site.CITATION:Atkinson, B W and Thompson, P, 2013. Mine water - optimising for site and environment, in Proceedings Water in Mining 2013 , pp 9-14 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By A Dal-Corobbo, R Zick

The coal mining industry is now faced with new regulatory requirements that limit the discharge of chlorides into receiving streams. To meet these new regulatory standards for treated mine water, a zero liquid waste approach was developed using advanced treatment technologies. The approach described in this paper will generate clean water for reuse in various energy endeavours or discharge to the environment, with no substantial liquid or solid waste from the treatment process leaving the site.CITATION:Dal-Corobbo, A and Zick, R, 2013. Zero liquid discharge in coal mining operations, in Proceedings Water in Mining 2013 , pp 221-226 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By R Redden

"The Didipio Gold-Copper project in the Philippines has been a well-defined reasonably high gold grade porphyry for almost two decades. OceanaGold are now bringing the project into production in late 2012 and have recently reoptimised the project with the goal of combining the inherent high grades with higher through-put than previously proposed that will see strong initial metal production. The project was discovered and well defined by 1995, but has seen some obstacles to development, namely sovereign risk, capital cost and project funding. The project strengths over this time that have kept the flames alive are: strong grades large orebody with low stripping ratios a simple beneficiation process and a clean high-grade concentrate strong support from the Philippines government.The initial study in 1998 used Gold and Copper price assumptions of $325/oz and $0.95 lb respectively. Today reserves are based on $950 and $2.85. So, being a porphyry with a large reducing grade halo, the deposit now lends itself to extraction on a much larger scale than before, without any significant capital expenditure as a larger open pit now dominates the project.Didipio is a game changer for OceanaGold, so it has been important to learn from history and to capitalise on a strong initial metal production profile. The project sits in a reasonably remote mountainous area of Luzon which sees annual typhoons and numerous short duration high intensity rainfall events and two rivers flowing through the project area, so it has not been without some innovative technical solutions.CITATION:Redden, R, 2012. Didipio - Learning the lessons, adapting and getting ready for production, in Proceedings Project Evaluation 2012, pp 67-76 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

May 24, 2012

By K Jupp, T J. Howard

Cliffs Natural Resources Pty Ltd (CNR) operates iron ore mines in the Koolyanobbing region of Western Australia. Ore is mined from three locations, separated by many kilometres. The ore is stockpiled at these locations, according to an in-house ore classification system (based on grade and source) and then trucked to the crushing and screening plant at Koolyanobbing. Lump and fines products are railed to Esperance for ship loading and export to Asian customers. CNR prides itself on the relatively low inter-shipment grade variability of the products. The Koolyanobbing crusher is fed using a daily blend plan, generated to maintain lump and fines product grades within acceptable tolerance ranges around targets. Achieving low variability requires predicting lump and fines grades as accurately as practical from the estimated head grades of the ROM ores potentially going into the blend. The grade prediction model may be either a direct prediction of crushed lump and fines grades and lump percentage, or be split into two stages: the bias between blasthole estimated head grade and crusher head grade and then the lump-fines algorithm for splitting the head grade between lump and fines products. The lump-fines algorithm comprises the percentage of lump and the difference between the lump and fines grades. We describe a weighted least squares (WLS) regression model for predicting crusher grades and lump proportion from the estimated head grade for Fe, P, SiO2, Al2O3, Mn and S. The method is applied to CNR production data, where the regression model explains approximately 60 per cent of the variance in the crushed ore grade, for both lump and fines. A further small but significant improvement in prediction can be achieved by including the ore classification data in the model. The regression errors exhibit strong positive serial correlation, indicating trends in grade error across multiple blend records. To compensate for the longer-term error, an exponentially smoothed model was developed and applied to the daily grade blend errors. This gave an increase in the longer-term variance explained and therefore an improvement in grade prediction.

Jan 1, 2009

By Golubkov OL, Fedotov PB, Shkylar FR

One of the fundamental parameters of the race- way is its extent (a{ o), which has a significant effect on the distribution of gas and material flows in the lower region of the furnace. pp The known relationships for determination of aC o in most cases link the length of the raceway with the parameters of the blast, while the para- meters of the coke layer, in which the raceway is formed, are either ignored or else expressed in terms which are difficult to determine experimen- tally. Furthermore, the coke combustion propert- ies are not always taken into account in current blast furnace operating practice with combined blast. A complex dimensionless parameter, which re- flects the properties of the interacting media, is the ratio of the kinetic energy of the hot, com- bined gas stream to the potential energy of the coke flow, burning at the tuyere in a gas of known composition. Statistical processing of experimental data on the extent of the raceway zone, obtained from literature and our own work on operational furnac- es, has led to a working formula of the following Form:

Jan 1, 1981

By A Van den Bulck, K Verbeken, O Vergote, I Bellemans

Viscosity is one of the most important physicochemical properties during pyrometallurgical operations. In the sub-liquidus regime, an important factor is the presence of suspended solid particles, yet its influence is not well-described in earlier literature, despite the significance of this factor. This project aims to determine the influence of spinel particles (Zn(Al,Fe)2O4) on the rheology of a multiphase synthetic PbO-SiO2-ZnO-Fe2O3-CaO-Al2O3 slag system. Three data sets with a wellcontrolled methodology and three different spinel sizes (small (13 μm), medium (34 μm) and large particles (76 μm)) were published previously, using a custom-built high-temperature rheometer. This study presents an additional data set of slag viscosity measurements, performed using a different apparatus, the Anton Paar FRS 1800, to verify the consistency of the earlier determined viscosity behaviour. Within this data set, no consistent trend could be found between the predicted wt per cent spinel and the relative viscosity. Therefore, additional quenching experiments were conducted to identify the morphology and experimentally determined volume fraction of the spinel particles in the slag. These measurements revealed a difference in spinel size across the samples and corresponding viscosity behaviour, emphasizing the importance of spinel particle size on slag viscosity. Once the spinel size was taken into account, consistent viscosity results (relative apparent viscosity and flow index) were observed across the two devices. This study confirms that, once all parameters affecting slag viscosity are considered, the viscosity behaviour of a heterogeneous slag can be uniquely determined. The resulting optimised slag viscosity models can be used to predict viscosity before processing, addressing relevant phenomena such as slag tapping, slag foaming and copper droplet settlement.

Aug 21, 2024

By G M. Zhomin, A S. Arkhipin, A Kondratiev

Viscosity of multicomponent slags is one of the crucial physicochemical properties for many industrial processes and technologies. While the viscosity-temperature relationship of completely molten slags can well be described by an Arrhenian-type law, the compositional dependence of viscosity is still not fully understood, especially in compositional regions with the lack of experimental data (eg at the glass-former concentration of 90 molar per cent or higher). In the present work major compositional relationships of the activation energy of viscous flow have been revised for numerous binary and ternary slag systems on the basis of experimental data collected and stored in the viscosity database OxiVis. For example, it has been found that the activation energy relevant to the polymerisation effect in binary systems of the MO-GFO type, where MO is the modifier oxide (ie monovalent K2O, Na2O, Li2O and bivalent CaO, MgO, BaO, MnO, PbO etc) and GFO is the glass-forming oxide (SiO2 or B2O3) is not always proportional to the third power of XGFO (contrary to the Urbain formalism) and can vary significantly dependent on the slag system. Also, the activation energy of the charge compensation effect has been revised for ternary systems of the AO-MO-GFO and AO-MO type, where AO is the amphoteric oxide (Al2O3, Fe2O3 or other). A simple polynomial model has been proposed on the basis of the carried-out analysis for estimation of viscosities of multicomponent slag systems. The model has been optimised against the experimental viscosities in the selected binary, ternary, and higher-order oxide systems and has been shown reasonable agreement with the experimental data.

Aug 21, 2024

By S Maritsa, E K. Chiwandika, S M. Masuka

The iron and steel industry is experiencing an increase in the use of iron and steel commodities within societies, decarbonisation pressures, depletion of high iron ore grades and high energy consumption. This necessitates scrap metal recycling, low-grade ore utilisation using the induction or electric arc furnace to achieve the global target of net zero CO2 emission. The available highquality scrap metal cannot sustain the steel industry but the world has unused hematite-goethite ores. It is the aim of this research that this resource be utilised using the induction furnace to sustain the steel industry in an environmentally friendly manner. Indurated pellets prepared from the hematite-goethite ore, 5 wt per cent limestone and 5 wt per cent coal addition were smelted in the induction furnace at 1350 ± 50°C with 25 mins holding time. The effects of basicity and carbon content were also investigated to optimise the smelting parameters. The results showed that the careful control of the basicity, and iron-to-carbon ratio maximised total metal recovery. The optimal basicity ratio was determined to be 1.3 and a carbon to iron ratio of 1.4 achieved a total metal recovery of 73 per cent. The metal recovery was closely related to the estimated slag melting temperature. The basicity ratio of 1.3 achieved the lowest slag melting temperature estimated to be around 1380°C based on the CaO-SiO2-Al2O3 phase diagram. The recovered metal had a comparable chemical composition and microstructure to that products from an ITmk3 furnace.

Jun 19, 2024

By X Dahe

SLon vertical ring and pulsating high gradient magnetic separators possess excellent mineral processing ability and have been widely applied to process oxidised iron ores. SLon centrifugal separators are applied to clean the SLon magnetic concentrate and remove quartz and other gangue minerals associated with a small portion of magnetite.This paper introduces the application of this technology in Hai Nan, Da Hong Shan and An Shan for processing oxidised iron ores.

Jul 11, 2011

By O Arafat, R E. McIvor, K M. Bartholomew

It is well known in the industry that good classification system performance is vital to efficient ball mill circuit performance. But what is meant by good classification system performance, and how is it achieved? Unfortunately, the perceived complexity of classification systems, and the day-to-day time demands placed on the practicing metallurgist, all too often put the low-hanging fruit of classification system optimisation in the ‘I’ll do it later’ basket. Additionally, lingering confusion about basics such as the relationship between circulating load ratio and ball mill circuit performance makes the optimisation objective seem nebulous to both plant metallurgist and designer.Some of this confusion can be eliminated by taking a step back from the overwhelming detail of sharpness of separation curves, circulating load ratios, cyclone feed pressures, vortex and apex sizes etc, and focusing on the purpose or function of the classification system – to apply mill power to particles that need further size reduction! The classification system efficiency (CSE) metric captures how well the classification system is performing its function with two quick and easy size distribution analyses.Once CSE is understood and implemented as the optimisation criteria, well-tested methods for improving CSE can be implemented and quickly measured at plant scale to give confidence that the right change was made.This paper will describe CSE and how it is measured in practice. Next, a guide for improving CSE through manipulation of design and operating variables in the classification system will be provided. Examples and case studies will illustrate the gains in ball mill circuit efficiency that can be achieved by maximising CSE.CITATION:Bartholomew, K M, McIvor, R E and Arafat, O, 2018. A guide to maximising ball mill circuit classification system efficiency (CSE), for operators and equipment designers, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 553–558 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By D Bertoldi, C Haines

"The Waihi Gold Mine (WGM) operated by OceanaGold New Zealand Limited is a wholly owned subsidiary of the OceanaGold Corporation of Australia. Traditionally WGM has stockpiled and processed separate campaigns of open pit and underground ore. The ore is processed via a conventional semi-autonomous grinding (SAG) / ball circuit (SABC). The low aspect SAG mill operates in a closed circuit with two 20" cyclones, whilst the ball mill is also a closed circuit with a 10" cyclone cluster. A major wall movement in April 2015 ceased open pit operations indefinitely, 18 months ahead of the mining plan. This immediately reduced the forecast mill tonnage leaving two options: begin campaign milling or change the operating strategy and target lower throughput. Additional cost pressures necessitated improved milling cost efficiency. The immediate ore restriction limited processing alternatives to within the existing major infrastructure. Available comminution circuit survey data laid the foundation for developing a comminution model using the JKSimMet™ software package (version 6, created by KJTech). A number of flow sheet variants were then evaluated based on predicted throughput and efficiency. The comminution models suggested opportunities for improved efficiency lay in reducing throughput and increasing utilisation rather than on/off campaign milling under the existing operating philosophy. A series of process alterations followed, delivering new cost efficiencies that maintained the current $/t processing cost. This paper aims to review the change in circuit performance and examine the decisions and challenges faced following the transition from a high tonnage SABC circuit to lower tonnage SABC circuit.Citation:Haines, C and Bertoldi, D, 2016. The Transition from Semi-autogenous to Autogenous Milling at Waihi Gold, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 303–312 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

A field trial of the prompt neutron-gamma SIROLOG technique was undertaken by the CSIRO - Division of Geomechanics at Callide Coalfields during July 1989. The trial investigated whether the sonde could reliably be used for the determination of Ash and Iron Oxide (Fe2O3) in coal seams, which had a highly variable iron content. Ten boreholes were logged, being water filled of a nominal diameter of 120 mm. The logging probe employed a 1.6 ¦g 252Cf neutron source and a 51 x 51 mm BGO detector. The source to detector distance was 15 cm. The results from one exploration borehole at the Dunn Creek Mine are discussed in the paper. The rms deviations for ash and iron determination between the neutron-capture predictions of the geophysical logs and the laboratory - chemical assays were 1.9 per cent Ash and 0.88 per cent Fe respectively. Using existing empirical equations which relate iron oxide concentration in coal ash to Initial Deformation Temperature (reducing conditions) at Callide, it may be possible to indirectly determine ash fusion properties as least as accurately, on a more detailed ply-by-ply basis, and more cost competitively than current laboratory techniques allow.

Jan 1, 1991