Search Documents

By K Nakashima, K Aya, T Sumita, N Saito

Electro slag remelting (ESR) is one of the methods used to produce high-cleanliness steel. In the ESR method, the product steel electrode is immersed in flux, and the electrode is melted by the Joule heat of the flux generated by high current. CaF2-based melts are mainly used as fluxes, but the electrical conductivity of CaF2-based melts varies widely among researchers and measurement methods. Therefore, this experiment aims to measure the electrical conductivity of CaF2-based melts based on the van der Pauw-Ohta method, which does not require the cell constant that is a fundamental error factor in electrical conductivity measurement at high temperatures. The measurement temperature was set at 1450–1600°C, and dehydrated Ar flowed through the furnace at 200 mL/min. Electrodes were fabricated by Pt-30mass per cent Rh alloy, and the electrodes were connected to an impedance analyser using a four-terminal probe. The electrodes were immersed in the melt, and the impedance and phase angle were measured by AC frequency sweep (50 Hz to 200 kHz). The electrical conductivity was then calculated by utilising the impedance’s real part values when the impedance’s imaginary component was zero. The electrical conductivity showed a positive temperature dependence. The electrical conductivity of 60(CaO⋅Al2O3)-40CaF2 melt increased with increasing temperature but was found to be roughly one-third of those of the previous studies. In the conductivity measurement of 60(CaO⋅Al2O3)-40CaF2 melt, the AC frequency with a phase angle of 0° was found to be different depending on the temperature and immersion depth. By sweeping the frequency, the impedance at the phase angle of 0° can be obtained, which enables us to measure the electrical conductivity more accurately.

Jun 19, 2024

The Pacific Rim countries ofAustralia, New Zealand, Papua New Guinea, Indonesia, Fiji, Philippines and Solomon Islands will be reviewed from an equity investors perspective.   The following areas will be covered: Country risks Exploration spending and activity Project development Taxation Relative cost of doing business Environmental considerations Political/bureaucratic situations Capital raising Equity markets as a source of funds Developing market funds The aim of the paper will be to outline the most attractive areas for investment by equity and private funds plus documenting the changes needed in the less favourable countries if they are to attract investors.

Jan 1, 1995

By M J. Newton

As part of the AMIRA P843 project Keeney and Walters (2008) describe how the principal components analysis (PCA) method can be used to identify classes of samples with similar metallurgical characteristics. However PCA does not take account of the location of each sample in 3D space. This paper describes a study to analyse the spatial distributions of the classes and determine appropriate modelling methods to control the estimation of the comminution parameters and mill performance indices into a 3D block model. This includes but is not restricted to geostatistical techniques that are used for grade modelling. The starting point for the study is the class definitions and the regression models for estimating the comminution parameters and performance indices. Each sample is assigned a class and the spatial distribution of each class has been analysed using different techniques including the calculation of variograms. This establishes whether the classes can be used as domain control for estimation into the block model – a procedure similar to using geological rock type domains for controlling the estimation of grades for a resource model. However, standard geostatistical estimation methods such as ordinary kriging assume that the variable being estimated is additive or linear. This assumption is valid for variables such as grade but this is not necessarily the case for the comminution parameters or the performance indices. Therefore the estimation procedure must either use variables that are definitely additive or the effect of potential non-additivity must be tested and accounted for where possible.The results of the study show how performance indices such as recovery, throughput and specific power can be estimated into the block model. This model is then combined with the geological model to provide a multi-parametric model that is used to optimise the mine planning and scheduling activities which can lead to significant improvements in NPV.

Sep 5, 2011

By J OÆDriscoll, R Butler, L Winter

The iron ore mining district of Labrador West and adjacent Quebec is Canada's largest iron ore producer with almost 50 years of production. The area is currently experiencing a period of renewed activity not seen in decades that includes new mine development, mine expansion and exploration for new iron ore resources. All of the past and present production and exploration programs in the district are centred on the Lower Proterozoic Superior-type iron formations of the Knob Lake Group, located within the Grenville tectonic province of the Canadian Shield. The Knob Lake Group is a continental margin sedimentary sequence which was deformed and subjected to greenschist to upper amphibolite facies metamorphism during the Grenville orogeny. Regional deformation and metamorphism plays a key role in making the iron formation of the Knob Lake Group economic. The distribution of orebodies in the district is controlled by superimposed F1/F2 synclines which causes thickening of the iron formation through repetition. Ore mineralogy consists of specular haematite, magnetite and locally martite with quartz as the major gangue mineral. Regional metamorphism has caused an increase in grain size of the ore minerals making it more amenable to concentrating and pelletising. Altius has been active in Labrador West since 2003 and is now the second largest licence holder in the district with several iron ore exploration projects. The Kamistiatusset project is located in the heart of the region's transportation, power and mining infrastructure. The property has seen limited previous exploration, but covers several significant iron ore prospects. Work by Altius includes a helicopter-borne magnetic survey, ground magnetic and gravity surveys, geological mapping, sampling and 6000 m of diamond core drilling all of which confirm both a favourable geologic setting and ore mineralogy.

Jan 1, 2009

By W Patton, I Minniakhmetov, H Talebi, U Mueller

The sustainability of mining projects is linked to informed investment decisions based on public reporting of exploration and mineral resource estimation results. In Australia, public reporting guidelines are established by the Joint Ore Reserves Committee reporting code through the JORC Code (2012). Although the assessment of uncertainty in the results reported is a requirement, this is often communicated qualitatively and evaluated subjectively. This can become a liability particularly in the early stages of mining projects when spatial domains of geological interpretation and mineralisation envelopes inform resource estimations’ reliability. A recent review of JORC reports found no reports used quantitative assessments of the geological interpretation or mineral resource estimation envelopes, and 27 per cent of reports did not address the question of quality of geological interpretation. Reports that did address the quality used 19 different terms to communicate quality. This work presents methodologies for quantitative uncertainty assessment and communication and explores how they could be applied in public reporting practice. Quantitative uncertainty reporting would benefit mine planning and financial modelling as they normally assume the geology is 100 per cent right (since no error is reported or only a single deterministic model is provided). The complexity, cost, and additional work of doing a quantitative assessment could hinder a straightforward implementation. This could be overcome if mining companies budget for quantitative uncertainty assessment and associated professional development. A compulsory requirement for the inclusion of uncertainty assessments in public reporting or adopting standardised subjective language would improve industry practice.

Mar 22, 2022

By E N. Sparg, O D. A Deuchar, F Needham

Decline shafts are an attractive option to both new and existing mining operations where there is a need to access an inclined orebody deposit via on-reef development so as to generate a return in the shortest possible time. There are many different technologies that are available to transport men, material and rock in incline shafts. This paper focuses on the applicability of two hoisting technologies for decline shafts, namely endless and direct rope systems. The pros and cons of each system are reviewed. A common concern with direct rope haulage systems is the possibility of generating slack rope during deceleration. This paper illustrates the issues involved in designing a system so as to avoid the possibility of slack rope. In conclusion, the key factors relevant to the selection of endless or direct rope haulages for a particular decline application are reviewed. The paper is a joint submission by FFE Minerals-Vecor and Qualter Hall UK.

Jan 1, 2005

By J M. Shekiro

In the chloride process to manufacture TiO2 pigment, feedstocks containing higher TiO2 contents (high-grade ores or HGOs) are favoured in order to minimise production of undesirable by-products. Most of today’s HGOs are produced through the smelting or reduction and leaching of ilmenite, processes which consume significant energy and/or produce large volumes of non-titanium materials that may have to be landfilled. In order to improve the economic and environmental sustainability of its TiO2 business, the DuPont Company, working with Kobe Steel Ltd, has developed an innovative process called TiRON for making HGO. Using a rotary hearth furnace, the process reduces ilmenite to a high TiO2 slag and metallic iron granules. The TiO2 slag is suitable for TiO2 pigment manufacture, and the iron is suitable for steel making. TiRON can process sand or rock ilmenite of varying compositions and particle sizes. Fossil fuel instead of electricity supplies the energy for the reduction. Dusts and off-spec materials are recycled. These process attributes, together with capital requirements estimated to be significantly lower, give TiRON substantial economic, environmental, and process flexibility advantages over conventional ilmenite upgrading processes. TiRON has been demonstrated at the semi-works scale, and preparations are being made to bring it to the pilot scale.

Oct 5, 2011

By A Esfahanipour, M Osanloo

Determination of cut-off grade?strategy is one of the most important stages of open pit mine planning and design. It is the parameter directly influencing the financial, technical, economic, legal, environmental, social and political issues in relation to mining operation. Choosing the optimum cut-off grade strategy that maximises the economic outcome has been a major topic of research workers for nearly one century. Many researchers have contributed in devising methods and algorithms, such as dynamic programming, linear programming, optimal control and so on for various aspects of its determination. In this paper, a non-linear mathematical programming for cut-off grade strategy optimisation is presented, considering the three main stages of mining operation introduced by K F Lane. In this model maximisation of net present value of mining operation, under the three constraints of mining stagesÆ capacities, considered as the optimisation criteria. Due to the discrete representation of the mining resource, the proposed non-linear formulation is approximated by a non-linear signomial geometric programming. According to non-convexity and the complexity of the proposed model, an augmented Lagrangian genetic algorithm was used to find the optimum cut-off grade strategy under varying and fixed price circumstances. To validate the proposed non-linear model efficiency, the results were compared with the results obtained by the K F Lane methodology. It was found that the proposed non-linear model works efficiently in the determination of cut-off grade strategy. According to the simplicity of the structure of non-linear programming modelling in comparison with dynamic programming it is hoped that, further development of this model would certainly provide the ability of considering managerial and technical flexibilities as well as incorporating more real mining conditions in the determination of cut-off grade strategy optimisation.

Sep 26, 2011

By S Hapugoda, J R. Manuel, M P. Ma, L Lu

Iron ore sinter quality depends heavily on the mineralogy, textures and physical structure of the sinter, which is formed upon solidification of the primary sinter melt. The interactions of the initial sinter melt with its surrounding materials will impact on the properties of the primary sinter melt and consequently the solidified structure of the sinter. By using a high-temperature visualisation system, in situ studies have been conducted on the effects of melt compositions (Al2O3, SiO2 and MgO) on the interfacial phenomena of the sinter melt on a natural iron ore substrate. It was found that the melt composition significantly influenced the wettability between the sinter melt and the iron ore substrate. The interactions between the sinter melt and the natural iron ore substrate were also examined. Such interactions can lead to further changes of sinter melt composition and hence the sinter melt properties that, in turn, further affect the wetting behaviour of the sinter melt.CITATION:Ma, M P, Lu, L, Hapugoda, S and Manuel, J R, 2013. Effects of melt composition on the interactions of sinter melt on a natural iron ore substrate, in Proceedings Iron Ore 2013 , pp 431-440 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By T Isaksson, J Anderson

The procurement process for underground construction contracts, in particular those contacts involving tunnel boring machines (TBMs), is subject to many complex and inter-related variables, including national and local politics, public policy, community involvement and media attention û as well as strict environmental and legal requirements. Other restrictions include the time available to adequately investigate geotechnical conditions and viable technical options to determine the best construction methodologies û including selection of tunnel boring machine characteristics and, those construction means and methods suitable for the specific geotechnical and environmental conditions. The latter are, most often, quite imperfectly understood. æGetting it rightÆ implies that an optimal configuration û of machine type, characteristics and associated methodologies û can be found and successfully implemented for a particular project. æFrom the beginningÆ implies that the lack of time issue can be successfully resolved. Within an international context this paper highlights a number of issues of concern which relate to tunnel procurement systems and the ways in which certain key processes are managed during planning, design and construction. The authors argue that there is considerable room for improvement in the way tunnelling projects are undertaken and an approach is discussed which has the potential for substantial gains in cost and schedule and reduction of risk. Savings, however, may only be fully realised if the new methods can be fully implemented by all parties involved. This, we believe, will require the rejection of ætraditionalÆ forms of management and procurement with associated changes in the roles and responsibilities of owner, engineer and contractor. Additionally, risk identification, assessment and mitigation are essential cost and schedule control process which have, to this point, been underutilised by the underground construction industry.

Jan 1, 1999

By B Flynn, P Knights

Low-loaders or 'floats' for relocating equipment in surface mines are limited to a capacity of approximately 350 t. In the iron ore industry it is desirable to be able to rapidly relocate excavators in order to maintain production rates within appropriate quality limits. In addition, the ability to rapidly relocate heavy equipment raises the possibility of improving the quality of repairs by performing maintenance in controlled shop conditions. However, many iron ore operations operate hydraulic excavators in the 600 to 800 t range, with newly released excavator models exceeding 800 t. These excavators are too large to float using conventional technology. This paper examines the potential for using multi-bogie transporters to relocate large hydraulic excavators in surface mines. Recent innovations have seen the development of modular transporters which can be coupled together to achieve larger platform areas. When separated, and with their drive bogies neutralised, these units are able to be towed behind prime movers and relocated between mines via public roads. The potential cost savings for relocating a Terex RH170 excavator in an open pit coal mine are examined. In the first six months of 2008, the analysis showed the potential for a 38 per cent reduction in total travel time with a corresponding revenue increase of approximately $350 k. The paper recommends that a feasibility study be conducted into offering a heavy equipment relocation service within the Pilbara region.

Jan 1, 2009

By S Chaudari, T Ren, T Harvey

Management of respirable dust on longwall face remains a challenging issue for mine operators, particularly for the new generation of thick seam longwalls. A fundamental understanding of the airflow behaviour around the shearer is critical for dealing with the dust control issue on longwall faces. Computational fluid dynamics (CFD) modelling techniques have been used in this study to conduct a detailed investigation of the air and respirable dust flow patterns around the longwall shearer. Three CFD models have been developed to represent different longwall cutting heights. The results of these modelling studies tallied well with field measured airflow data from different mines. The validated thick seam longwall face model was then used for detailed parametric studies to simulate the effect of various parameters and dust control concepts. The dust control options investigated include various spray configurations, shearer clearer, modified cutting sequences and shearer scrubbers of various capacities to minimise the respirable dust migration towards the walkway area of the longwall face. This paper presents a summary of the results of these CFD modelling investigations.

Jan 1, 2005

A process was developed based on the thermal hydrolysis and precipitation of iron from solutions resulting from the leaching of zinc plant residue. A study was made of the hydrolysis of iron, at temperatures in the range 140-220°C, in both pure solutions of ferrie sulphate and in leach solutions derived from plant spent electrolyte.At 200°C hydrolysis of pure ferric sulphate solutions results in the precipitation of ferric oxide, Fe2O3, at low acid. concentrations, and a basic salt, Fe2O3.2S03.H20, at hIgher acid concentrations. At 180°C ferric oxide is precipitated at low acid concentrations, but at higher acidities. carphosiderite, 3Fe203.4SO.3.9H20, is the stable phase. Frequently a mIxture of ferric oxide and carphosldente IS produced at 180°C, the ratio of phases being dependent on the non-equilibrium experimental conditions.With solutions derived from plant spent electrolyte hydrolysIS at elevated temperatures results in the precipitation of jarosite compounds of the type NaFe3(S04)2(OH)6 The precipitation of natrojarosite jarosite, and ammonio-jarosite was studied in detail. Temperature, free acidity, and the concentration of sodium potassium, and ammonium ions are critical factors which affect the extent of precipitation.A process based on ammonio-jarosite precipitation was tested in a pilot plant.An alternative method of iron removal based on the addition of zinc oxide calcine, to neutralize excess acidity, and the precipitation of ferric oxide was also tested in the pilot plant. Both processes appear economically favourable...

Jan 1, 1967

By J Geronimo, P Kumar, Z Yussupova, M Yahyaei, M Powell

This work goes beyond the general perception of how the well-known mine to mill process can be applied, by applying deeper knowledge along the mining chain. Grade deportment and dilution are considered at the mining stage, and modelled with the new SMI blast movement simulator, linking with the block model data. Assessing the shift to a considerably more competent section of the orebody is quantified via substantial milling trials at standard and higher-intensity blasts. These were stockpiled for batch processing through the mill to ensure feed integrity. The trial work included operating the mill at widely different fillings to develop Grindcurve milling responses. Additionally, model informed process control is initiated via a mill prediction tool.It has been found that accounting for blast movement for the higher intensity blasts could generate additional value of around $1.5M per blast. With the high-intensity blast and changing mill control, the plant was easily able to exceed projected mill throughputs with the far more competent Pipeline ore. Strategies to shift the workload and debottleneck the milling circuit were proposed and proven during the milling trials, demonstrating an increase in throughput of 7 per cent despite running at a lower SAG mill speed, and potential of 16 per cent for increasing the SAG mill to standard operating speed. A number of process improvement opportunities have been identified to enhance current productivity and ensure long term capability to process the considerably more competent future ores. All of this is being linked in with the major digitisation program at the Barrick Cortez site, with an objective of linking all the data into a mine-wide process optimisation system, that can embed the processes by providing process-wide data access and production support via the future dynamic models linking ore body knowledge to productivity along the full process chain.CITATION:Powell, M, Yahyaei, M, Geronimo, J, Yussupova, Z and Kumar, P, 2018. The designed approach to mill liner optimisation – experience at Pustynnoye mine, Kazakhstan, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 595–612 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By X Feng, X Zhang, W Sun, Y Zhe, K Hou, B Zhao, H Liu

Pulang Copper Mine, being China's largest newly built mine using block caving, boasts an annual production capacity of 12.5 million tons. Production level and roadway stability hold the key to the successful application of block caving. However, with Tong Kuangyu being the only mine in China which has applied such a method, we currently lack relevant experience in the successful application of the method. This paper has studied the influence of different rock mass zonings, fault thickness, fault dip angles, on-site construction quality on the production level, roadway stability of block caving through numerical simulation and analysed the roadway stability in different kinds of support solutions so as to ensure the successful application of block caving in Pulang Copper Mine. The results have shown that the existing support method in Pulang Copper Mine can meet the requirement of roadway support in zone II and III, but could not satisfy the demand in terms of support strength in the relatively fragmented zone I area. When roadway passes through the fault, the deformation of surrounding rock and plastic zone of roadway will gradually decrease with the increase of fault dip angle; the deformation of surrounding rock and plastic zone of roadway will gradually increase with the increase of fault thickness. An ideal support effect can be achieved through the joint support of grouting and bolting when roadway passes through the fault. In the measured model of on-site construction, there is stress concentration in the intersection between the access and transverse drift of ore removal. Therefore, the stability of the roadway can be improved by improving the construction quality. CITATION:Sun, W, Hou, K, Zhang, X, Feng, X, Liu, H, Zhe, Y and Zhao, B, 2018. Research on supporting technology for production level roadways of block caving in Pulang Copper Mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 95–106 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By K Ehrig, V Liebezeit, Y Li, B Pewkliang, M Smith, E Macmillan

Pre-concentration of low grade ores via the rejection of low/no value materials based on fragment size is the subject of many published papers and studies over the past decade. However, the possibility of upgrading should not limited to low grade ores given the high cost of capital, energy, water, reagents, and ultimately tailings storage across the mining industry. Mining and processing facilities at Olympic Dam consist of an: 1) underground mine where ore is extracted via sublevel open stoping and 2) integrated processing plant located on the surface which produces Cu-cathode, Au-Ag bullion and uranium oxide concentrate. Blasted ore is trucked/trained to underground crushers which produce an ore feed with a product size P80 = -145 mm. Crushed ore is then hoisted to the surface and delivered to the ROM pads via an overland conveyor. The typical copper grade of mill feed is approximately 2 wt%. A rapid assessment of the potential to upgrade Olympic Dam mill feed prior to the ROM pads via rejection of low value materials based on fragment size was completed using existing data. Three separate datasets were utilised to assess the deportment of Cu, U, Au across size ranges of 200 mm down to sub-8 m. Cumulative grade vs cumulative mass distribution graphs for each element were produced. This data clearly demonstrates that Cu, U, Au grades remain constant down to ~212 m, which happens to be the liberation size of the sulfides. Hence, no potential to upgrade the ore stream via rejection of +200 mm - to ~212 m sized materials prior to milling. Mineralisation within the Olympic Dam Fe-oxide Cu-U-Au-Ag deposit (IOCG) occurs as disseminated sulfide grains within granite- to hematite-rich breccias. The typical sulfide grain size is sub-200 m that supports the outcomes of the grade deportment by fragment size study.

Nov 10, 2020

By G T. Jemwa, F Rousseau, F J. Wolfaardt, J A. M Rademan, P W. Smit

Mining companies are increasingly faced with the challenge of reducing operating costs while maximising throughput and profitability. At the same time, the grade and quality of treated ores are becoming poorer and more variable, resulting in suboptimal process performance.It is now widely accepted that strategies to drive operational goals must revolve around improving plant availability, reliability and process efficiency. In particular, progress in plant automation and control systems has seen a trend towards unified frameworks for control and optimisation of mineral processing plants. These frameworks seek to seamlessly integrate different roles and tasks involved in process operations - IT, automation, plant maintenance and operations. An integrated solution framework for reducing process variability, increasing process efficiencies and maximising plant availability and reliability is discussed within the context of a typical milling circuit. The framework exploits a real-time analysis ægapÆ evident in production operations that prevents timeous identification of equipment and process failures. This is achieved by leveraging predictive analytics for equipment health monitoring, control loop monitoring and advanced regulatory control solutions towards enhanced process performance, improved asset management and regulatory compliance. The framework provides for early and actionable warnings on equipment and process degradation using real-time operational data.Resolving these problems can potentially avoid unplanned downtimes, process instabilities and other operational surprises, thus ensuring optimal plant throughput and optimal process behaviour for improved recoveries. Integrating control systems and plant automation with advanced analytics to analyse and optimise processes enables operations to achieve reductions in the variability of key process parameters. In addition, early detection of equipment malfunction or suboptimal process conditions leads to improved equipment availability and reliability. Ultimately, these operational gains reflect in profitability because of plant throughput and recovery gains. These benefits are demonstrated using data from a South African gold mining operation, where such an integrated asset and process health monitoring framework for process optimisation has been implemented.CITATION:Jemwa, G T, Wolfaardt, F J, Smit, P W, Rademan, J A M and Rousseau, F, 2013. Towards an integrated framework for asset and process health monitoring and optimisation on a milling circuit, in Proceedings World Gold 2013, pp 137-148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

A very wide range of technologies are utilised in the mining and processing of ores and a great deal of effort is expended in the development of ænew technologiesÆ to improve mining performance and economics. Traditionally, technology and people have been treated as separate aspects of an operation, when in fact they are inextricably linked. The successful implementation of new technologies is entirely dependent upon the actions, enthusiasm and skills of people, both as individuals and working in groups. This paper discusses the role of technology in mining and how new technologies are implemented by the industry. The paper argues that existing technologies have not been fully or adequately utilised and that effort should be re-focussed on the implementation of technologies that have been taken for granted for many years. The need for greater emphasis to be placed on the management of the human-technology interface is discussed.

Jan 1, 1998

By G Bubner, C Gaughan

Magnetite mineralisation within the South Middleback Range has been known since the early 1930s; however, it was not until 1989 that BHP (then owners of the Middleback Ranges mining leases) drilled 10 700 m of diamond core into what was then known as the Iron Duchess low-grade deposit. In 2002 a review of Iron Resources left in the Middleback Ranges and the identification of downstream processing benefits using magnetite as a primary feed source led to the commencement of an 18 000 m resource drilling program of the high-grade core of the Iron Duchess low-grade orebody (renamed the Iron Magnet deposit). This paper describes the geology, processes and procedures used since drilling recommenced in early 2003. The Iron Magnet deposit is located 53 km southwest of Whyalla in the South Middleback Range, South Australia. It is a Paleoproterozoic stratabound magnetite deposit that lies down-dip and lateral to the Iron Duke hematite deposit, hosted within the Lower Middleback Iron Formation of the Hutchison Group meta-sediments within the Cleve subdomain of the Gawler Craton. Magnetite bearing host units within the Lower Middleback Iron Formation can be divided into a æmixedÆ basal sequence, a lower iron carbonate unit, a middle iron talc unit and an upper iron silica unit, all units grading up sequence and laterally into one another. The magnetite mineralisation is hydrothermal in origin. The strongest consistent mineralisation coincides with the iron carbonate unit, and the hematite orebodies of the Iron Duke are interpreted to represent up-dip supergene enrichment of the same unit. The Iron Magnet occurs within a large-scale parasitic syncline-anticline pair on the west limb of a larger syncline. Major bounding north-south shear zones occur on the east and west sides of the deposit. Cross-cutting west-northwest, northwest, northeast and east-northeast trending faults displace mineralisation. The commencement of drilling in 2003 lead to the migration of geological and geochemical databases, re-logging and re-assaying of all old cores that intersected the deposit, updating of logging codes and procedures, and strict Qa/Qc procedures to ensure the study satisfied JORC standards. External consultants were used for auditing and bench marking. The strong geophysical responses of magnetite and the wealth of close spaced ground magnetic and gravity data already completed over the Middleback Ranges allowed for refining of drill hole targets for the drilling program. It also provided an indirect method for ascertaining magnetite grade and tonnage volumes.

Jan 1, 2005

By M Ben, P de Donato, M Kongolo

The extensive literature on sulfide flotation indicates that pyrite poorly floats under alkaline condition. Xanthate concentration has a positive effect on pyrite flotation, but above a pH of 11, pyrite seems to be strongly depressed, independently of the concentration in xanthate. In this investigation, aeration and xanthate concentration effects were studied for pyrite flotation conditioned at pH 11 with lime. Results presented in this paper include surface infrared analyses and pulp chemistry measurements which have showed that aeration had a dual effect on pyrite flotation. It induced pyrite surface activation by oxygen, and oxidation of ferrous iron to ferric hydroxides or oxyhydroxides species. It also favoured dissolution of CO2, leading to calcium carbonate precipitation and adsorption onto pyrite surface. Both CO2 dissolution and ferrous oxidation generated protons and decreased pulp pH. Pyrite flotation was observed to be effective with a statistical monolayer of xanthate that could be adsorbed as mixture of dixanthogen and metal-xanthate complex. Non-floated fractions showed high amounts of carbonate, and presence of hydroxyl iron sulfate (Fen(OH)m(SO4)p, xH2O) which have inhibited the hydrophobicity effect of adsorbed xanthate. Environmental desulfurisation could be improved by aeration control causing pyrite oxidation and pH decrease to reach optimal flotation condition with a relatively low xanthate concentration.

Jan 1, 2005