Search Documents

Crocidolite deposits in the Hamersley Ranges, NW. of Western Australia, occur over a length of 180 miles and a width of 20' to 30 miles. Their stratigraphic environment and mineralogy is comparable to that of similar deposits of the Cape Belt, South Africa. It is probable that the known exposures' represent only a small portion of the total extent.Current production is wholly by Australian Blue Asbestos Pty. Ltd. at Wittenoom Gorge and has been in the order of 1,2,000 to 14,000 long t.p.a over the past six years.INTRODUCTIONThe Hamersley Ranges are located in the NW. Division of Western Australia and extend, approximately, from latitudes 21° 30' to 23°S and longitudes 117° to 1200 E. Their mean height above sea level is 2,000 ft, and they rise from 600 to 800 ft above the general level of the tableland which extends SE. from the coastal town of Roebourne.Mt. Bruce, the highest peak, is 4,024 ft above sea level. The ranges are intersected by numerous north-flowing streams, which are dry during the greater part of the year. These streams have carved deep gorges, and it is in these that the principal deposits of crocidolite outcrop.The presence of the mineral was first recorded in 1917, but the deposits remained untouched until 1937 when strong market demand for crocidolite resulted in considerable prospecting and mining activity, particularly in Yampire, Wittenoom and Dale's Gorges. It was established also that the blue asbestos belt extended from Willi Wolli Springs NW. to Millstream station, Le., over a length of 180 miles and a width of 20 to 30 miles. A number of attempts were made to develop and treat the Yampire and Wittenoom...

Jan 1, 1964

By Hookings H. J

UNDER a contract relating to the sale of a Broken Hill concentrate, the differentiation between granular and slime concentrate is determined by the proportion of the material which will pass a 200-mesh (I.M.M. standard) screen, and this has led to considerable attention being devoted to the question of laboratory sizing tests with screens of this order.It was found that many of the screens turned out by the makers during the war, and also since its termination, did not conform with the I.M.M. specifications as closely as some supplied in pre-war days. A perfect screen is hardly to be expected, but when the above contract was framed the parties anticipated that, by special care being taken during manufacture, a screen at least as good as the best pre-war screens would be available. This, however, has not proved to be the case, and the large irregularities in screens recently supplied render them useless for sizing determinations under the contract. The makers were approached through the Institution of Mining and Metallurgy, London, with the view of obtaining a few screens conforming as closely as possible to the 200-mesh I.M.M. standard, and in response to a request twelve pieces of screen were...

Jan 1, 1922

THE object of this paper is to review certain features in connection with the mining of narrow lodes, say up to 20 ft. or so wide. The types of ore-body to which it is intended to refer are those which occur. chiefly as fissure or shear-Iodes-that is, those lodes which are to be found in belts of country which have been subjected to dynamic stresses, resulting in the formation of cracks and fissures, into some of which has been concentrated sufficient metal-bearing material to form ores. Very frequently one of the walls of such a lode is found to be a fault, or plane of differential movement.The first point which comes up for consideration is the shaft and its position. From the information afforded by the prospecting which has been done on a lode relative to the dip, nature of country, &c., the position of the main hauling shaft can be determined. For purposes of general utility the hangingwall is generally chosen, if a vertical shaft, though, on account of freedom from creeps, the foot-wall would be safer. Vertical shafts are preferable to underlie shafts in many ways; but wherethe lode maintains a flat dip the cost of cross-cutting at the various levels becomes very heavy'. This difficulty may to some extent be modified· by sinking a vertical shaft in the hanging-wall...

Jan 1, 1912

Stripping of Fe (III) from D2EHPA Using Different Reagents The common way to extract Fe(III) from an organic solvent is by using concentrated acidic solutions. The stripping of Fe(III) from organic solvent Di-2-ethylhexyl phosphoric acid (D2EHPA) by hydrochloric acid (HCl) solutions has been found to increase with increasing the acid concentration. However, the use of a concentrated acidic solution such as 6 M HCl can degrade the organic molecules. In this research, to increase the efficiency of Fe(III) stripping from D2EHPA, effect of some acids, salts and buffer solutions was studied. Influence of Tri-butyl phosphate (TBP) as modifier on the Fe(III) stripping operation was also investigated. According to the results, the best Fe stripping recovery was achieved in the presence of low acid concentration and the salts which was 72.4 per cent oxalic acid, 70 per cent ammonium oxalate and 75 per cent buffer of oxalic acid and ammonium oxalate. The results also showed a better recovery in the presence of the buffer rather than the salt. Finally, increasing the concentration of TBP, HCl and H2SO4 resulted in a higher stripping efficiency of Fe(III). However, in the presence of oxalic acid and its salts increasing the reagent concentration did not increase the stripping efficiency and at this condition, the recovery of iron remained constant.

Sep 13, 2010

In 1948, it became clear that the ventilation system of The Zinc Corporation Limited and New Broken Hill Consolidated Limited mines, would be inadequate for future operations. The,paper describes in detail the process of designing an entirely new ventilation system for a large underground mining operation. The system was based on a single new upcast airway to be located on the boundary of the two properties, which were to be ventilated in parallel as two separate ventilating districts.From calculations of resistance, and assessments of future air requirements, the duties of a new exhaust fan to be located on the collar of the upcast airway were specified as 700,000 cubic feet per minute at 2·6 in. w.g. total pressure for initial operation in 1953 increasing to a maximum of 900,000 c.f.m. at 3·6 in. w:g. total pressure ten years later. The economic size of the new airway was calculated from a consideration of the first thirty years operation of the system, and it was decided to provide a 20 ft. diameter concrete-lined shaft.The new system went into operation five years after the initial planning, and the effect of the difference between actual and predicted rates and distribution or production are discussed. The final result was entirely satisfactory.INTRODUCTIONThe first proposal for an investigation of The Zinc Corporation Limited-New Broken Hill Consolidated Limited ventilation system with a view to putting it on a proper technical basis was made in 1938. A new Main Shaft was then being sunk, and it was decided to postpone the enquiry until this had been completed to No. 14 Level, when operations would be temporarily suspended and the shaft commence to operate as a major airway. The investigation was completed early in 1940, when Z.C. Ltd. upcast fan was...

Jan 1, 1956

It is the purpose of this paper to produce some evidence on the accuracy to be expected from normal assay procedure using the usual first class equipment, and to examine the effect that many assaying inaccuracies have on reported metallurgical recoveries.Generally speaking, the evaluation of the gold content of a mineral ore sample by the fire assay method is a relatively simple process.A weighed quantity of finely ground ore is fused with suitable fiuxes including litharge and a reducing agent to give a button of lead and a quantity of slag. The shower of lead produced by the reduction of the added litharge collects the gold and silver present in the ore, concentrating the values into the lead button.The button of lead, after separation from the slag, is, on heating in an absorbent cupel in a current of air, reoxidised to litharge and absorbed into the cupel leaving a gold and silver bead in the cupel. This bead' is heated in a solution of nitric acid to dissolve the silver, leaving the gold undissolved to be dried and weighed. Knowing the original weight of the ore and the weight of the gold prill the value of the ore is easily calculated.Summarising1. Fusion Process.-Ore plus fiuxes give a slag plus lead button.2. Cupellation Process.-Lead button is re-oxidised to litharge leaving a gold and silver bead.

Jan 1, 1952

The area (330 sq. miles) shown on the map of the Brocks Creek District (Fig. 1), was mapped by the Northern Territory geological party of the Aerial, Geological and Geophysical Survey of Northern Australia. This work was done in two stages:-(i) In 1935, an area of 30 sq. miles around the Golden Dyke mine was mapped by P. S. Hossfeld, Senior Geologist, and A. H. Voisey, Assistant Geologist. The results were described in a detailed report (10).(ii) In 1939, an area of 300 sq. miles in the Brocks Creek district was mapped by C. J. Sullivan (Senior Assistant Geologist), and V. M. Cottle and S. N. Kiek (Assistant Geologists) under the general supervision of P. S. Hossfeld (Senior Geologist).An outline structural map, together with some geological notes was published (1), but that map does not show the amphibolites, and the relationship between ore occurrence and general geology is not emphasised. The publication of the detailed maps and reportwas postponed indefinitely as a result of war. The original mapping was based on air photographs with a scale of approximately 1 in. to 1,200 ft., and all detail which could be shown at that scale was mapped. Features recorded included rock types, details of structure, mineralisation, and surface workings, creeks and soil boundaries. Underground mapping was also carried out. The present map is much simplified from the original, but it is hoped that it shows sufficient information to reveal close relationship between structure, granite, sills of amphibolite and gold occurrence. About 50 per cent. of the area is covered by deep soil or alluvium, and in these portions the geology of the underlying rocks was not determined with accuracy, though in many places strike trends could be deduced from air photographs.Because the A.G. & G.S.N.A. had published the geological notes and map referred to above, and because the publication of the detailed report and maps is still postponed indefinitely, approval has been given by the Bureau of Mineral Resources, Geology and Geophysics (which took over the affairs of the A.G. & G.S.N.A. at the termination of its operations) to the preparation of the present paper so that information would be available to the public.The views expressed in this report are those of author. The results of the investigation suggest that in areas where granites are predominantly concordant with bedding, ore deposits may be found at approximately the same stratigraphic horizon. It is thus important to correlate beds even though their relationship may have been obscured by faulting and folding.

Jan 1, 1950

By A Hanna

Quarries around Auckland have reached or are reaching the ends of their lives, which raises issues about rehabilitation. Significant volumes of 'cleanfill' are generated by the City, particularly during phases of urban renewal and development. Emplacement of the fill in quarries removes the problem of fill disposal and provides an opportunity for restoration of the quarry site.There is a compatibility between quarrying and cleanfilling because at quarries:Truck routes are already established Neighbours are accustomed to the effects and appropriate buffer distances have been established Bringing fill into a site attracts aggregate sales and is very efficient. Fill originates from construction sites and ad-hoc excavations and therefore it is not surprising that sampling has shown the quality to be variable. Both Winstone and the Auckland Regional Council have surveyed undisturbed soils in the region to attempt to determine natural background levels of common contaminant substances. Comparison of these levels with delivered fill shows that a high proportion of delivered materials can be regarded as mildly contaminated. Therefore the term 'cleanfill' is, in the Auckland region at least, a misnomer and the term 'managed fill' has been adopted.Historically and presently the only control on quality of 'cleanfill' has been some visual inspection. This leaves the fill operator open to potential liability for creating a contaminated site. Implementation of controls at WinstoneÆs operations has progressed slowly, over some ten years. This is mainly due to the perception that mobility of contaminants within and out of the landfill will be very limited because of the near-neutral pH and abundance of clay minerals in the fill. The methods of control and results of environmental risk assessments at WinstoneÆs Puketutu Island Quarry will be briefly described.

Jan 1, 2002

The importance of timbering, not only from a financial point of view but from an actual mining point of view, is so often overlooked or slightly glossed over by the average expert and investor, that I have thought it would prove interesting to go into the matter and to invite discussion upon the subject. We will first take small veins, or reefs as they are termed in some mining countries; and by small veins it is intended to denote fissures from a few inches to three feet. The ore body is supposed to be confined within well defined walls free from gangue matter, unless the casing can be defined as such. Now, if the walls are smooth and moderately hard, no timbering is required other than the stulls, which are braced from wall to wall in order to form platforms or stages to stope from. Should the reef from wall to wall prove payable, or should the vein be of a character to prohibit cleaning or sorting; and it be determined to send the whole of the stone to the, reduction works, the stuUs should be left in place until the section or block of ground is worked out, in order that if a weak spot in the walls (especially the hanging) occur, it would be possible, without any particularly extra expense or difficulty often times accompanied by danger to brace and secure the slabs. After the block became entirely stoped, it would pay where labour was cheap to remove the majority of timbers to stull another section.

Jan 1, 1901

Willyamite from the type locality, Consols mine, Broken Hill, N.S.W., has been re-examined, and found to consist of zones with widely different Co:Ni ratios. The name willyamite is redefined to include the portion of the (Co, Ni)SbS series with cobalt in excess of nickel. Willyamite is pseudo-cubic, with the three axes equal to within 0·001 A.

Jan 1, 1970

Particle Size Measurement of TiO2 Nanoparticles in Non-Aqueous Solvent by Interactive Force Apparatus Under an Electric Field

Sep 13, 2010

Very little has been written about the discovery and early history of prospecting of ironstone deposits in the Iron Knob-Middleback Range area of South Australia, the main source of supply of ironstone (hematite) for the Australian steel industry, and scanty though the record is, much of it is wrong or misleading.With the help of several people, to whom acknowledgement is made at the end of the paper, the writer has unravelled some of the story, but not the whole story. It is hoped that publication of this paper will stimulate interest in others, who may be able to supplement this account from family records, from the files of newspapers, or from archives.

Jan 1, 1969

OWING to the gradual depletion of the hitherto plentiful supply of firewood in the immediate vieinity of Queenstown and Gormanston, which caused a steady increase in the cost of fuel for domestic purposes, the Mount Lyell Company took steps several years ago to make available as a substitute electric current from its Lake Margaret hydro-electric supply. In order to make this practicable it was necessary that the cost of electric power for heating purposes should compare favourably with the cost, of fuel, and the installation of domestic appliances brought within reach of the average householder, and efforts have been continuously directed towards this end since the year 1928.WATER HEATERSThe installation of electrical apparatus in local dwellings began with hot-water services, the heating elements being the types then procurable on the market and adapted to meet requirements.These, however, did not prove satisfactory, but the study of their bilure resulted in a type being developed locally which has overcome all difficulties. The first type of water heater evolved was an outside circulation one the element of which consisted of an iron pipe through which the water passed, insulated with micanite and wound with nichrome wire, the latter being covered with alundun cement to keep it in position and prevent oxidation. This was insulated on its outside surface with a layer of asbestos flour, and connected to the hot-water container as shown in Fig. 1. It was found, however, that the iron pipe had a short life, due to a certain amount of acidity in the water, and a copper pipe was substituted which proved very durable. Some heaters with this improved type of element are still operating after six years of use. The resistance wire is run at a very low current density, which ensures durability.

Jan 1, 1927

Perhaps one of the most important conferences or symposia which our Institute has conducted, was the joint Aus. LM.M./AJ.M.E. meeting held in Canberra in May 1978, with the theme International Resource Management (Woodcock, 1978).We were privileged to witness active participation in the meeting by outstanding personalities from the mining and metallurgical industries of Australia and New Zealand, the United States of America, Canada and the United Kingdom and to hear addresses on subjects of international significance to the mining and metallurgical industries.Our Institute is one concerned with professionalism.The principal objects of The Institute as described by our founders include, "promoting the arts and sciences connected with the economical production of the useful minerals and metals, and the welfare of those in the industries, by meetings for social intercourse, and the reading and discussion of professional papers, and to circulate by means of publications amongst its members and associates, the information thus obtained".Sir Maurice Mawby (1968) said in his Presidential Address to the Institite, "the most important aspect of these objects was the promotion of the arts and sciences of the mining industry".Why is it then, that a large proportion of the papers given at the meeting in Canberra dealt with world wide social aspects of the mining and metallurgical industries, rather than the technology, the arts and sciences of mining and metallurgy as principal factors in international resource management?The answer is quite simple of course, and that is that the social and political factors are the principal factors which create the demand for basic raw materials and in the long term determine the costs and prices of the commodities which our professional abilities are drawn upon to produce.

Jan 1, 1979

By Jones S. C

A specific arc can be cut in hard rock formations using a specially designed multistep piloI bit, variable sized drift joint and long heavy control rod as a stabilizer rather than the Vaughan Thompson "Lifting" arc cuttingequipment. The rate of deflection can be controlled after an initial determination of behaviour in any particular rock type.

Jan 1, 1966

The use of black and white and colour infrared film in remote sensing of natural resources is reviewed. In heavlly-forested areas such as New Zealand, the main value of the method is in surveying the vegetation cover to detect the existence of plant communities characteristic of specific geological formations. By contrast in arid areas of Australia where the vegetation cover is sparse and where rocks and soils are well exposed, the method can be used in detecting different rock types or other geological differences.

Jan 1, 1972

By Baker G

The exposures resulting from development work, following on the discovery of a new shoot of hIgh grade ore at the north end of the Sardine tin mine, during 1952, have provided an unusual opportunity to study the oxidation of a stannite-rich ore. Through the kindness of C. C. Morton, Chief Government Geologist of Queensland, an exactly located suite of specimens representative of the exposures was supplied by J. and W. Reddie. This was later supplemented by a number of specimens culled from a parcel ofrepresentative ore submitted to the Melbourne Ore Dressing Laboratory for testing.The Sardine tin mine, near Ewan, Queensland, has been the outstanding producer of the Kangaroo Hills Mineral Field. Since its discovery in 1918, up to 1952 it has yielded about 1,500 tons of cassiterite concentrates, and about 85 tons of stannite concentrates. The outcrop ore averaged 35% tin oxide, but the grade declined with increasing depth, and by 1930 had fallen to 7% tin oxide. In the northern section of the mine the ore shoots show a downward passage to complex primary s.ulphide ore, containing cassiterite and abundant stannite.The orebodies occur in a series of fissures in a crushed zone about 50 ft. wide in slates and quartzites that have been intruded by granite (Connah, 1952). A quartz porphyry dyke forms the footwall of the original main lode in its southern part, being traced' from the surface to' the No. 4 level (173 ft. vertical depth), and two narrow dolerite dykes were encountered in the workings north of the main...

Jan 1, 1954

Using a cylindrical hydrocyclone with a long vortex finder as the separator, a batch sizer was developed for the fast comparative sizing of the coarse solids normally encountered in mineral pulps.Operating times as short as 2 or 3 min gave separations ranging from 16 mesh down to the subsieve sizes.Reproducibility was good and sensitivity was adequate for most applications.

Jan 1, 1968

At an early stage of the examination of most prospects, samples are taken; and the sample values obtained play an important part in determining the subsequent history of the prospect. It is, therefore, important that. eveJJy effort should be made to interpret asfully as possible the meaning of the observed results. In this connection, it is suggested that examination of the assay values of mine samples by simple statistical methods may bring to light information of considerable value, which might otherwise be missed.Although expert statisticians may derive more information from the available data, those who are, like the writer, less proficient mathematically, may also benefit by applying quite simple statistical methods. At least they will develop a useful habit of thought bywhich they become aware at all times that sampling results only provide estimates of the truth, but that an assessment of the precision of such results may be possible. The object of this paper is to provide some evidence of. the truth of these statements, by theuse of a few very elementary statistical calculations.General.The idea that any mine sample is subject to error from a variety of causes is a very familiar one. Doubt always exists with regard to the representativeness of a perfectly cut sample, and other errors may arise through imperfections of sample cutting, crushing, splitting and assaying. Some causes of error may give rise to "constant" errors, others may cause variable but one-sided "systematic" errors, and others again may bring about variable results without any tendency toward bias on the average. In statistical language, mine sample values are subject to errors which may have either assignable causes or chance causes. The former are those which can be isolated, or should be capable of isolation, while the latter are those remaining when all assignable causes have been removed. A single constant assignable cause brings about bias in all results, and one or more than one variable assignable cause brings about variation between individual results and perhaps an overall bias. The system of chance causes that would remain if all assignable causes were removed would cause variation between individual results but no overall bias. There is no sharp practical line of distinction between the two types of cause) of error; nor is it ever possible by any method of statistical analysis to be certain that there are no assign...

Jan 1, 1950

THOUGH the literature on the chamber process is considerable, it mostly refers to European conditions. Owing to the demand for acid for flotation and leaching at the mine, it may be necessary to work the process under other conditions. Consequently, some results obtained during the chlorination days at Mount Morgan, within the Tropic of Capricorn, may be useful for reference when working in a similar climate. Though the chambers must be protected against tropical storms, thorough ventilation should be provided, with plenty of space between the chambers, which are almost invariably crowded together. Not only does the space assist in the cooling of the chambers, but it is very desirable during repairs, when lead andtimber have to be hoisted up. The connecting flues between the chambers, which are fairly efficient mixers and condensers, should be round, supported from above, and with the least possible timber about them. Their position and arrangement deserve careful attention. Lattice work will be sufficient protection for the sides of the chambers, and the roof should be high and well ventilated. The Mount Morgan plant, crowded and not well situated, consisted of seven chambers (four over 50 ft. in length), one Glover tower 7 ft. 2 in sq. x 20 ft. high, one Gay Lussac 9 ft. sq. x 30 ft. higb, also one 5 ft. diam. x 25 ft. high. There was one pipe column 4: ft. sq. x 14 ft. 6 in. high. The chambers were run as one unit, and were much lower than those usually constructed in Europe-less than 15 ft. high. Provided that suitable timber can be obtained, 20 ft. is quite low enough. It should be quite satisfactory to use round poles for the studs, and so admit more air space between studs andlead.

Jan 1, 1920