Search Documents

By Edgar Dunn

PART I.-DETERMINATION OF GASES IN SMELTER FLUES. IN 1907, upon arriving in Anaconda to take up work in the testing department of the Washoe Reduction Works, the. following problem was met at the car step, so to speak: complete and. exact analysis of gases, not only at the stack, but also in all departmental flues. Taken up to employ time not otherwise needed for regular testing department work, instructions were extremely liberal for a commercial plant, to the effect that accuracy should not be sacrificed to speed. In December, 1907, the work was temporarily transferred to the Great Falls Smelter, and some of the methods here given were there worked out. Differences in smelting operations at Great Falls and Anaconda, however, necessitated further investigations and the development of a new method for S03 determinations at the latter plant, where work was resumed in July, 1908, and completed about a year later. At the time of inception of the work, data (not only on percentages, but even on methods) were found to be meager in the extreme, for one or the other of two reasons: either entire lack of experiment at a large proportion of smelters, or disinclination on the part of the managements to divulge data of any description pertaining to either results or methods. In making determinations of gaseous constituents of flues, two methods are open to consideration: 1, the drawing out of a sample, and collection of the same as a whole, to be removed to the laboratory for later analysis; and 2, the absorption in situ on the flue of one certain constituent, disregarding others for the time being, or perhaps combining two or three in one determination. The first is generally the more rapid, but it is also the more inaccurate, method of analysis, even with special type absorption apparatus, being the more largely subject to error, both of reading, and also because of leakage during complicated manipulation in the laboratory. The amount used for analysis must also, because of limit of container, be small for the first method, and an average gas is very seldom obtained, necessitating for a fair average result a large number of determinations. Consequently, when we balance the time spent in a dozen determinations of short-time samples as against the time employed in making two or three long-time determinations of various constituents in situ, we are not so certain in our statement as to the relative speed of the two methods. Moreover, the method of analysis in the laboratory of 100 cc. of flue gas is satisfactory only when constituents thus determined are present in considerable quantity, results being simply approximate when determining such compounds as sulphur dioxide, sulphur trioxide, carbon monoxide and dioxide, and arsenic trioxide and water vapor, none of which are carried in all smelter flues in amounts in excess of (or even approaching) 1 per cent by volume. Special condi-

Jan 8, 1913

By Walter Remmers

THE fact that gray iron increases in volume, cracks and distorts upon repeated heating and cooling is rather common knowledge. In ingot molds, Diesel engine pistons, carburizing boxes, continuous furnace parts, grate bars, stoker parts, and all castings that are subjected repeatedly to high and low temperatures, the phenomenon of growth presents a vital problem. Ingot molds distort and produce cracks which result in seams or laps and later appear as defects in the finished product. The heads of Diesel pistons frequently fail by cracking in a stellar shape. This is attributed usually to the result of permanent growth. Distortion and change of dimension of furnace parts frequently renders them entirely unusuable. In chain grate stokers, mechanical difficulties frequently are caused by the growth of the links. In proper operation these links should never attain a temperature sufficiently high to start growth; nevertheless, some have grown 1/8 in. on an 8-in. length when improperly operated. Even though the phenomenon is generally known there still exists a deficiency in the explanation of the mechanism of this growth. The field of investigators of this subject has a decided variation in opinion concerning the causes. The problem is of sufficient importance therefore to warrant further consideration.

Jan 1, 1930

By P. H. Turnock, R. D. Pehlke

The effects of mutual interactions between elements on the solubility of nitrogen in liquid iron alloys containing chrormium, columbium, molybdenurn, nickel, or silicon have been determined. The equilibrium nitrogen solubilities in the liquid iron alloys were measured by the Sieverts method. The second-order effects caused by the presence of chrormium, columbium , or silicon in the melt were found to be significant. The solubility of nitrogen in liquid iron alloys containing several alloying elements has also been measured as a function of melt temperature and nitrogen pressure. The heat of solution of nitrogen in microcomponent iron alloys has been found to be a function of the logarithnz of the activity coefficient of nitrogen, irrvespectilje of the composition of the melt. The heat of solution of nitrogen in pure liquid iron was determined to be 1265 ± 450 cal per g-atom of N over the temperatxue range 1600° to 1800°. Sieverts ' law was obeyed for all melt compositions studied in the pressure interval 0.4 to 1.0 atm. The solubility of nitrogen in liquid pure iron and in many dilute binary liquid-iron alloys has been the subject of many investigations. Pehlke and Elliott' made a comprehensive investigation on this subject in which they summarized and compared previous researches. However, the practical application of these solubility studies requires prediction of the nitrogen solubility in the multicomponent alloys encountered in operating practice. The interaction parameter as defined by wagner2 has been used to predict the behavior of a solute in a complex alloy, and a modification of this approach has met with reasonable success in several instances.'1"5 The necessity for extending the nitrogen solubility data on binary alloys is caused by the lack of direct measurements of the solubility of nitrogen in molten alloy steels. A direct comparison between measured solubilities and those predicted for multicomponent alloys based on data in binary systems has been made in only a few instances, and most of these were reviewed by Langenberg,6 who developed a graphical technique for predicting nitrogen solubilities in multicomponent iron alloys. The solubility of nitrogen has also been studied over the entire Fe-Cr-Ni ternary system by Humbert and Elliott.? Both studies compared the solubilities computed from binary iron alloy data with those measured in ternary alloys in the liquid state at 1600°C. Most of the nitrogen solubility measurements referred to above were for iron alloys at 1600°C; thus, the ability to predict nitrogen solubilities in molten iron alloys has been restricted primarily to alloys at 1600°C. Recently, Nelsson8 devised an approximate method for calculating the change in nitrogen solubility in molten iron alloys as a function of temperature, but an assumption of regular solution behavior limits the applicability of the method. Chipman and Corrigan9,10 have developed an empirical correlation. based on the activity coefficient of nitrogen in the iron alloy at 1600°C, which facilitates the estimation of nitrogen solubilities at higher temperatures. This method also has limitations, due to the necessity of calculating the activity coefficient for nitrogen in a multicomponent iron alloy at 1600°C from the nitrogen solubility data for binary iron alloys. The shortcoming of such a straightforward approach to the problem of predicting nitrogen solubilities is the disregard of mutual interactions between elements in a complex iron melt. This investigation was conducted in an attempt to provide a more reliable method of predicting nitrogen solubilities in multicomponent iron alloys. The effects of the mutual interactions between chromium, nickel, silicon, molybdenum, or columbium in iron were studied, using the Sieverts' technique1,7 to measure the effects of alloy composition, temperature, and pressure on the solubility of nitrogen in ternary liquid iron alloys.

Jan 1, 1967

By R. K. Hopkins

Fox a great many years fusion welding has been used in and around petroleum refineries, but it is only within six or seven years that the more important pressure vessels have been constructed by this process, because before that time the properties of fusion welds would not withstand such rigorous service. Since the adoption of fusion welding for the construction of this equipment, the refiner has required pressure vessels suitable for operation over a very wide range of conditions. On the one hand, vessels must operate at extremely high temperatures, in the range of 950° to 1000° F., and on the other vessels must be suitable for operation at sub-zero temperatures down as low as -75° F. Also, vessels are required suitable for operation at pressures upwards of 1000 lb. per sq. in., and as low as a 29-in. vacuum. In addition, vessels are required to withstand the attack of very corrosive mediums. It has been a rather difficult task for the fabricator to meet all of these requirements, but as a result of the extensive research carried on by steel manufacturers and several fabricators of class I vessels, practically all of these demands have been met. In order to meet the refiners' requirements for this wide range of conditions, the fabricator has worked closely with the metallurgist. This has enabled him to choose the proper base metal for each service condition, but it has been the fabricator's problem to develop a welding rod and welding technique, as well as a heat-treatment, that would produce in the welded vessel characteristics in and around the weld comparable to those in the base metal. Where corrosion is not a serious problem, and where the operating temperatures are not too high, ordinary carbon steel has served very well. But when corrosion is serious, and/or when the temperatures are either very high or very low, it is necessary to use some form of alloy steel to give satisfactory service.

Jan 1, 1935

By R. J. Reynik

A semiempirial small flunctation theory of diff- sion in liquids is presented, which employs a fluctuation energy assumed quadratic for a small atomic or molecular displacement and Einstein's random-iralh model. The resulting diffusion equation is given by In these equations. D is the diffusivity, is the average liquid shite coordination number (at interatomic distance d. cm. T is the absolute temperature, xu. em, is (the diffusive displacement. K, is the quadratic fluctuation energy force constant, and rg, cm, are the radii oj diffusing atoms A and B, respectively. The quantities Xn and K are calculated from the computer-filled values of the slope and intercept. respectively. The radius of self-diffusing atom or radii and of diffusing atoms A and B are eta United and compared with values reported in the literature.. The predicted linear variation of diffusivity with. It tempera lure htm been observed in approximately thirty-iire metallic liquid systems, and in over seventy-fiee other liquid systems, including the organic .alcohols, liquified inert gases, and the molten salts, ALTHOUGH the average density within a macroscopic volume element of liquid is constant for fixed total number of atoms. pressure. and temperature, there exist microscopic: density fluctuations within the respective volume element. As such the microscopic volume available to an atom and its Z first nearest neighbors at any instant of time fluctuates above and below the average volume available to these atoms. If one assumes that liquid state atoms vibrate as in a solid. and further postulates that the mean position of any atom in the liquid state is not stationary. but shifts during every .vibration a distance 0 5 j 5 xo. then every atom in the liquid state continuously undergoes diffusive displacements which vary in the range 0 5 j 5 ro. Mathematically. for a binary liquid system consisting of atcrms A and B. the maximum diffusive displacement. .YO, is defined by the equation: where d is the average liquid state interatomic distance at specified liquid state coordination number Z. and v~ \ and vg are the effective radii of diffusing atoms A and B: respectively. For self-diffusion. r^ equals rg , and Eq. [I.] reduces to: It is interesting to note that Eq. [l] or [2] can be used to compute the radii of the diffusing atoms, provided one had an experimental evaluation of xo. As such. the computed radii could be compared with metallic or crystallographic ionic radii to ascerlain the electronic character of the diffusing atoms. Thus it is proposed that in the liquid state the n~otion of an atom relative to its original equilibrium position of oscillation represents the thermal vibration of any atom and its Z first nearest neighbors. while the small and variable displacements. 0 5 1 5 xc,. of the centers of oscillation represent the complex diffusive motions of the atoms at constant temperature and pressure. This is consistent with data obtained from slow neutron scattering by liquids1 ' and resembles an itinerant oscillator model of the liquid state.'" It is further postulated that the atomic displacements characterizing the liquid state diffusion process are essentially a random-walk process. As such. it nlay be described by Einstein's equation:' where D is the diffusivity. sq cm sec-'. j2 is the mean square value of the diffusive displacement. and i> is the frequency of density fluctuations giving rise to diffusion. FORMULATION OF DIFFUSION EQUATION The effective spherical volume occupied by an atom, as a consequence of a microscopic density fluctuation which enlarges the volume available to any atom, exceeds its average liquid state atomic volume by an amount: where AV is the enlarged spherical volume, v is the radius of the diffusing atom. and j is the elementary displacement distance from the original center of oscillation of the vibrating atom to a new center of oscillation position. For small atomic displacements. where c is a constant whose value depends upon the assumed geometry of the enlarged volume. For a spherical increase in volume, c equals 4nr2. Following the treatment of Furthl' and ~walin." assuming the enlarged volu~nes AL7 for the diffusing atoms are distributed in a continuunl. the probability of finding a fluctuation in the size range 0 5 j 5 xo defined by Where c includes the geometric constant cl and Eij) is the fluctuation energy causing the volume change. But the proposed model assumes all the Z first nearest-neighbor atoms are centers of oscillation. and hence the probability that any of these atoms is adjacent to a fluctuation of magnitude 05j5xo is unity. Thus:

Jan 1, 1970

By Albert F. J. Bordeaux

Alluvial gold was first discovered in Guiana in 1852, in the sands of the Arataye river, by Paulino, a Braziliaii convict. During the following years, gold was found also in the rivers Orapu, CirubQ, etc. In 1873 the famous placers of the Sinnamary system were opened: Saint-Elie, Dieu-Merci, Adieu-Vat, and Couriege. This group of mines has produced nearly $10,000,000, according to official records, not including the gold that escaped the taxes. The discoverer was a mulatto named Vitalo. Except in a few rich spots, the gold was rather evenly distributed along the creeks. In one instance, gold was found in the red dirt from the slope of a hill, which, after transport to the creek, gave an amount of 150 kilograms. The placers of the Mana system, Enfin, Elysee, Pas-Trop-Tot, date from 1878, and their production has been about %g5,000,000. In 1888, the Awa placers, along the boundary bet.ween the French and Dutch Guianas, on the Maroni and its tributaries, were discovered. They have yielded $12,000,000. The only industrial company, the Dutch Guiana Freiich Minillg Co., produced in 15 years about 2,500 kg. of gold, worth $1,500,000. From 1893 dates the famous Carsewene discovery, in territory then in dispute between France and Brazil. A settlement was made recently in favor of Brazil, by arbitration of the Switzerland State Council. Carsewene is said to have produced about $18,000,000 in six years (1894-1900), but not even one-fourth of tho production went through French Quiana and

Jan 1, 1911

By S. B. Twiss, P. R. Basford

The relationship between areas of iron powders, briquettes, and sintered compacts and tensile strength has been determined. It has been found necessary to distinguish between two types of areas which exist in such powders—a macroscopic area due to the shape and size of particles and a microscopic area due to pores and cracks in the surface. Only the macroscopic area, specifically the area due to particle irregularity, contributes to tensile strength; the microscopic area cannot be forced into contact with adjacent particles ond does not participate in bond formation. Of the two methods of area measurement employed in this study—permeability to liquids and gas-phase adsorption—only the former is useful for determining the roughness factor. A measure of this roughness, (area measured by permeability to liquid) -f- (orea of powder with the same size distribution, but made up of spherical particles), is shown to be uniquely related to tensile strength at constant density. The other important factors in determining the strength of sintered-metal compacts are the density and presence or absence of surface oxide. THE manufacture of metal parts by the process of powder metallurgy is an important and rapidly growing industry. Progress has been rapid and continuous, largely because of the excellent research in the field. Nevertheless, the process remains inherently complex and empirical. Several investigators have shown that the properties of the final compact must depend on many variables; namely, shape,' size distribution,"-" nd compositiona of the original particles, the pressure necessary to compress to the desired density, the density of the compact, the time and temperature of sintering, and so on. Through the application of some new techniques to the study of powders and compacts, and the correlation of a number of observations of known variables, the present paper attempts to clarify and simplify the underlying theory of the powder-metallurgy process. Any theory must start with the obvious fact that the strength of a compact, its most useful property, is due to the formation of welded areas between adjacent particles, and attempt to deduce what effect other variables will have on (a) the area and (b) the intrinsic strength of these welds. Such welded areas can be demonstrated by electron micrographs, as in Fig. 1. It was believed that (a) could be most directly studied by means of surface-area measurements on the original powders and on the compacts made from them; the area decrease should be related closely to the welded area. A representative group of eleven iron powders from commercial sources, and made by a variety of processes, was chosen for this study. In addition to the surface-area measurements, correlations were established between the tensile strength and all the known variables which might possibly affect it. The results are quite unexpected. They indicate that the situation is much simpler than the authors had anticipated. The strength of the sintered compact is determined, indeed, by no more than three variables; viz., the irregularity of the original particles, the density of the compact and, in exceptional cases, the amount of surface oxide. All three had been recognized previously as having some effect on the tensile strength, but in the absence of the special techniques and interpretations to be developed here, there could be no suspicion that they were the only relevant variables. Materials and Methods Material—All the iron powders were commercial products obtained from the Amplex Division of Chrysler Corporation. Powders A, B, C, and J were very pure electrolytic iron. Powder D was made from oxidized scrap reduced by heating with an excess of cast iron. Powder E was a high-grade iron ore reduced by hydrogen. Powder I was prepared by atomizing molten cast iron in an air blast, quenching the droplets in cold water, and crushing the coarse powder. Mill scale (oxide) is added and the mixture heated to reduce the high carbon content. The other powders were all prepared by reduction of iron oxides, such as mill scale. They

Jan 1, 1959

By R. D. West

Miscible displacenzent recovers all oil in the area contacted by the injected .fluid, whereas water or immiscible gas drives usually leave substantial amounts of oil as residual. However, the Door mobility ratios associated with a gas-driven miscible displacement cause the sweep pattern efficiency to be much lower than that obtained with water flooding. One way in which the sweep eficiency in a miscible displacement process can be increased is by decreasing the mobility behind the flooding front. This can be achieved by injecting water along with the gas which drives the miscible slug. This water reduces the relative permeability to gas in this area and thus lowers the total mobility. The main operating conditions for the simultaneous injection -vrocess are that a zone of gas exists between the miscible slug and the leading edge of the water and that a su,@cient amount of gas be injected with the water to form the pas volume which is being left in the water zone. Laboratory model studies have shown that the ultimate sweep pattern efficiency can be as high as 90 per cent for a five-spot flooding system. If gar alone is used as the driving medium an ultimate sweep-out efficiency of about 60 per cent would be obtained in the same system. I INTRODUCTION The miscible displacement processes are a step towards total oil recovery. Conventional gas or water drives usually leave 25 to 5.0 per cent of the oil as residual in the swept portion of the reservoir. This residual can be eliminated if the oil is driven by a fluid with which it is miscible. At some reservoir conditions natural gas will become miscible with the oil. This is the "high pressure gas process".' More often, the oil does not contain enough light hydrocarbons to cause the gas to become miscible with the oil at reasonable pressures. In these cases a small band of fluid which is miscible both with the oil and gas must be kept between them2. Less than 2 per cent of the reservoir volume of the slug material is needed to keep the displacement miscible. Both processes work in the same manner, recovering all of the oil in the portion of the reservoir contacted by the injected fluids. The only difference is the manner in which the miscibility between the oil and the injected gas is obtained. Previous publications have contained detailed descriptions of these processes.1,2,3,4 However, total displacement of the oil in the swept region does not guarantee an efficient recovery process. The amount of oil to be recovered is also determined by the fraction of the reservoir contacted by the flood. This fraction is largely determined by the mobilities of the fluids. (The fluid mobility is the permeability of the rock to that fluid divided by the fluid's viscosity, k/p). This. dependence of the fraction swept on the mobility ratio has been shown in previous studies. Fig. 1 shows the ultimate fraction swept in a five-spot system as a function of the mobility ratio. The small drawings show the location of the areas left unswept for two different mobility ratios. The ultimate fraction of the reservoir swept is here considered to be attained when the producing stream contains less than 5 per cent oil at reservoir conditions. THE GAS-DRIVEN MISCIBLE DISPLACEMENT Since there is no oil left in the swept region after miscible displacement the mobility in this region is very high. It is often 50 times the mobility in the unswept regions. This means that the fraction of the reservoir contacted by the injected fluid will be less for a gas-driven miscible displacement than for a conventional water or gas drive. For a five-spot injection system, water would contact the entire reservoir volume, and the low pressure gas would contact about 90 per cent of this volume, while a gas-driven miscible displacement would only contact about 65 per cent of the reservoir. This poor sweep efficiency often offsets the benefits obtained through miscible displacement. Fig. 2 shows what the recovery curves for the three processes might look like for a five-spot system. The curves show the fraction of the in-place oil recovered as a function of reser-

By Dwight Farnham

Description of Quarry THE shale used at the Renton plant of the Denny-Renton Clay Coal Co., for the manufacture of vitrified paving brick occurs in a hill rising from 200 to 300 ft. above the level of the valley in which the plant is situated. The shale deposit, which is of unknown thickness pitches about 10° to the southeast. The 150-ft. face worked extends approximately east and west, so that the clip, as shown by the photograph, is to the left and into the hill. The shale is overlain with about 50 ft. of gravel, 70 ft. of clay, and 30 ft. of mixed loam and gravel, making altogether from 125 to 150 ft. of overburden. Disposal of Overburden The overburden is removed by sluicing. For this purpose a No. 2 Joshua Hendy giant is used, throwing a 12-in. stream', and having 60 lb. pressure at the nozzle. The water is drawn through an 8-in. pipe from Cedar river, about 1,000 ft. distant, by means of a Worthington four-stage centrifugal pump, direct connected with a 100-h.p. motor placed just south of the factory, and 1,500 ft. from the nozzle This plant handles the material satisfactorily to a height of about 75 ft. above the level of the top of the shale. When the higher levels are worked, an auxiliary plant consisting of a four-stage Byron Jackson centrifugal pump with a 100-h.p., belt-connected motor, is thrown into the system. This plant is situated on top of the shale and can be discerned at the extreme right of the trestle work in Fig. 1.

Jan 9, 1914

By G. R. Rubly, H. J. Steele

The San Manuel property is in town&ips 8S and 9S, range 16E, Gila and salt River Base and Meridan, State of Arizona. This area is in the Old Hat mining district, southern pinal county, and is about 31/25 miles southwest of the town of Mammoth on the San Pedro River And one mile south of the Mammoth mine at Tiger, Arizona, The property consists of over 150 contiguous lode claims. The old Hat district was prospected prior to the civil war, but there was little or no production until 1881.1 The chief producers have been the Mammoth and Mohawk mines, now consolidated and operating as the st. Anthony Mining and Development Co., Ltd. Production to 1936 was $5,200,000, of which 83 pet was gold.2 Since 1940 the production has been chiefly lead and zinc, and some molybdenum and vanadium. There are a few small properties in the vicinity that have produced very minor tonnages of copper ore. In the San Manuel group there are claims which have been held continuously from 1906 to the present time, and at least two churn-drill holes were put down on or near the outcrop in 1917. No logs for these holes are available, but it is assumed that the grade of copper encountered was not sufficient to encourage further exploration. A small amount of ore has been shipped from open cuts on the San Manuel outcrop area, but there is no record of the tonnage Or grade. It is estimated that not more than 50 tons were mined. These cuts, plus a few shallow shafts and some short adits indicate limited and unenthusiastic prospecting at San Manuel. In 1942, through the efforts of James M. Douglas, R. B. Giffin, Victor Erickson, and Henry W. Nichols, owners of the Sari Manuel group, the Reconstruction Finance Corporation and War Production Board authorized the United States Geological Survey to investigate the property, and by their recommendation, the United States Bureau of Mines was authorized to put down a limited number of churn-drill holes. The Bureau of Mines carried On drilling from November 1943 to February 1945 Seventeen holes were drilled, varying from 305 to 1990 ft in depth. The property was brought to the attention of Magma Copper Co. in June 1944, and an option agreement was made with the Owners. Subsequently, a group of claims lying north of the original group and held by the Apex Lead Vanadium Mining Corp, and a group to the east held by the Quarelli family, were optioned. A drilling program was laid out to conform to the Bureau of Mines pattern, and drilling started in December 1944 Sari Manue1 Copper Corp. was incorporated September 1945, and has carried on the exploration program to the present time. Geology General The mineralized outcrop, chief copper mineral of which is chrysocolla, is a tri-

Jan 1, 1949

By G. R. Rubly, H. J. Steele

The San Manuel property is in town&ips 8S and 9S, range 16E, Gila and salt River Base and Meridan, State of Arizona. This area is in the Old Hat mining district, southern pinal county, and is about 31/25 miles southwest of the town of Mammoth on the San Pedro River And one mile south of the Mammoth mine at Tiger, Arizona, The property consists of over 150 contiguous lode claims. The old Hat district was prospected prior to the civil war, but there was little or no production until 1881.1 The chief producers have been the Mammoth and Mohawk mines, now consolidated and operating as the st. Anthony Mining and Development Co., Ltd. Production to 1936 was $5,200,000, of which 83 pet was gold.2 Since 1940 the production has been chiefly lead and zinc, and some molybdenum and vanadium. There are a few small properties in the vicinity that have produced very minor tonnages of copper ore. In the San Manuel group there are claims which have been held continuously from 1906 to the present time, and at least two churn-drill holes were put down on or near the outcrop in 1917. No logs for these holes are available, but it is assumed that the grade of copper encountered was not sufficient to encourage further exploration. A small amount of ore has been shipped from open cuts on the San Manuel outcrop area, but there is no record of the tonnage Or grade. It is estimated that not more than 50 tons were mined. These cuts, plus a few shallow shafts and some short adits indicate limited and unenthusiastic prospecting at San Manuel. In 1942, through the efforts of James M. Douglas, R. B. Giffin, Victor Erickson, and Henry W. Nichols, owners of the Sari Manuel group, the Reconstruction Finance Corporation and War Production Board authorized the United States Geological Survey to investigate the property, and by their recommendation, the United States Bureau of Mines was authorized to put down a limited number of churn-drill holes. The Bureau of Mines carried On drilling from November 1943 to February 1945 Seventeen holes were drilled, varying from 305 to 1990 ft in depth. The property was brought to the attention of Magma Copper Co. in June 1944, and an option agreement was made with the Owners. Subsequently, a group of claims lying north of the original group and held by the Apex Lead Vanadium Mining Corp, and a group to the east held by the Quarelli family, were optioned. A drilling program was laid out to conform to the Bureau of Mines pattern, and drilling started in December 1944 Sari Manue1 Copper Corp. was incorporated September 1945, and has carried on the exploration program to the present time. Geology General The mineralized outcrop, chief copper mineral of which is chrysocolla, is a tri-

Jan 1, 1949

By J. J. Kanter

There has been much research and commercial development in recent years in the use of chromium and nickel in steels of various types, including those intended for high-temperature service. By "high-temperature steels" are meant those specifically designed for service at elevated temperatures in steam plants, oil refineries and other industries where high-temperature operations are conducted. This paper is devoted to some preliminary data on the effect of silicon on certain of the most popular chromium-molybdenum steels now being used in quantity by the refining industry and includes a short statement on the influence of copper in steels intended for high-temperature service. Uses of Silicon Next to oxygen, silicon is the most widely distributed and abundant of the earth's substances. Although classed as a nonmetal, it is highly important in the metallurgy of all steels, having been used for years as an efficient and economical degasifier and deoxidizer. Silicon is added to various steels in the form of ferrosilicon, generally at the end of the heat so as to avoid oxidation losses. With acid steels it is added in the furnace (also in the ladle) and generally with basic steels is added in the ladle, so as to avoid reaction with the basic lining through high-temperature acidic reaction with silica, which may be formed by oxidation of the silicon alloy. Several grades of ferrosilicon are available, containing, respectively, 15, 50, 75 and 90 per cent Si. By far the largest tonnage produced is the 50 per cent grade although the 75 and 90 per cent ferro-silicons are used as ladle and furnace additions in the manufacture of steels of high silicon content. The introduction of silicon into steel as an alloying element is well known in connection with high-yield-strength constructional steel for bridges, ships, car construction, etc., and it is also well known as an alloy-

Jan 1, 1938

By J. J. Kanter

There has been much research and commercial development in recent years in the use of chromium and nickel in steels of various types, including those intended for high-temperature service. By "high-temperature steels" are meant those specifically designed for service at elevated temperatures in steam plants, oil refineries and other industries where high-temperature operations are conducted. This paper is devoted to some preliminary data on the effect of silicon on certain of the most popular chromium-molybdenum steels now being used in quantity by the refining industry and includes a short statement on the influence of copper in steels intended for high-temperature service. Uses of Silicon Next to oxygen, silicon is the most widely distributed and abundant of the earth's substances. Although classed as a nonmetal, it is highly important in the metallurgy of all steels, having been used for years as an efficient and economical degasifier and deoxidizer. Silicon is added to various steels in the form of ferrosilicon, generally at the end of the heat so as to avoid oxidation losses. With acid steels it is added in the furnace (also in the ladle) and generally with basic steels is added in the ladle, so as to avoid reaction with the basic lining through high-temperature acidic reaction with silica, which may be formed by oxidation of the silicon alloy. Several grades of ferrosilicon are available, containing, respectively, 15, 50, 75 and 90 per cent Si. By far the largest tonnage produced is the 50 per cent grade although the 75 and 90 per cent ferro-silicons are used as ladle and furnace additions in the manufacture of steels of high silicon content. The introduction of silicon into steel as an alloying element is well known in connection with high-yield-strength constructional steel for bridges, ships, car construction, etc., and it is also well known as an alloy-

Jan 1, 1938

By Ralph C. Holmer

IN the field of mineral exploration, 1956 can be looked upon as the International Geochemical Year. This is not because of unusual developments in geochemical prospecting but rather because of the world-wide effort in geochemistry and the realization that geochemistry is now an established exploration method. Use of mining geophysics has continued to increase. Those extensively employing exploration techniques indicate that developments of the past few years have permitted better programming of methods, from reconnaissance to location of drill- holes. There is greater diversification of methods- reliance is not placed on results of one. However, it is realized that often it is more economical to drill an anomaly than to conduct additional expensive geophysical surveys

Jan 2, 1957

Jan 1, 1902

By P. H. Wendland

Calculations are presented for the design of a silicon photodiode in which the incident light beam makes multiple passes between the detector surfaces. Total internal reflection is used for this "light-trapping" effect. By this means, the optical path length can be extended to several millimeters, while the electrode separation remains less than 102 cm, as required for nanosecond response time. Data are presented for a Schottky barrier photodiode constructed on a multiply reflecting silicon base wafer. It is shown that the long-wavelength response is considerably extended in such structures without a corresponding sacrifice in high-speed response. The development of efficient and powerful lasers at 1.06 p has stimulated interest in detectors which operate at this wavelength. In typical silicon photodiodes, for detecting 1.06 p radiation, the requirements for high speed and high sensitivity are mutually exclusive. Since the absorption coefficient is only 25 cm-', a lo-'-cm path length is required to absorb 92 pct of the incident 1.06 p radiation. If the electrode separation is greater than 10 cm, however, the carrier transit time will be greater than 1 nsec. This problem can be solved by allowing the incident light beam to make multiple passes between the electrodes. The optical path length can then be extended to several millimeters, as required for complete absorption, while the electrode separation remains less than 10' cm, as required for nanosecond response time. In a typical photodiode geometry, one ohmic contact and one rectifying contact are formed on the two opposite surfaces of a base wafer, and the wafer thickness determines the electrode separation. The objective of the multiple reflection design is to allow all 1.06 p radiation to enter the detector front surface and to form the back detector surface so that no 1.06 radiation can exit. Total internal reflection at the back detector surface is well-suited for light trapping of 1.06 p radiation because the relatively large dielectric constant of silicon leads to a critical angle of 16.5 deg for total internal reflection. LIGHT TRAPPING It is well-known that, as light passes from one medium such as air into another medium such as glass or silicon, the angle of refraction is always less than the angle of incidence. In the limiting case, where the incident rays approach an angle of 90 deg with the normal, the refracted rays approach a fixed angle +, beyond which no refraction is possible: this is called the critical angle. It follows from Snell's law that where = critical angle, n - index of refraction of air, n' - index of refraction of the medium. Applying the principle of reversibility of light rays, all internal angles of incidence greater than +, will produce total internal reflection and "light trapping". The index of refraction of silicon at 1.06 p is 3.5,' and the critical angle is thus 16.5 deg. Fig. 1 shows these relationships for silicon. This very small critical angle in silicon is significant because all incident angles between 16.5 and 90 deg will produce total internal reflection and "light trapping". This effect can be implemented with a "prismlike" geometry, so that incident light can be introduced into the sample without loss and "trapped". PHOTOSIGNALS A precise knowledge of the absorption coefficient at 1.06 in silicon is of critical importance to the design of fast and efficient silicon photodiodes for 1.06 radiation. Dash and newman2 show a value of 25 cm-l, and our measurements have corroborated this value. Assuming that the collection of photoinduced minority carriers is perfect, the quantum efficiency of a photodiode is dependent only on the absorption coefficient. It then follows from Lambert's law that where QE is the quantum efficiency in pct, a is the absorption coefficient, d is the optical path length, and the reflectivity at the surface is assumed to be completely suppressed by an optical interference layer. Fig. 2 gives the maximum quantum efficiency for 1.06p radiation of a silicon photodiode with optical path length d, using Eq. [2]. The ultimate response time of a fully depleted photodiode to an incident light pulse can be considered to be the arrival times of all photoinduced carriers at the contacts, i.e., the minority carriers at the junction interface and the majority carriers at the oppo-

Jan 1, 1968

THE primary interest in the subject of this chapter lies in the fact that various heats of steel made to the same chemical specification do not always-have the same properties. The properties considered here, of course, are those inherent in the ingot immediately after solidification and not qualities imparted by variations in subsequent mechanical or thermal treatment. The expression "made to the same chemical specification" is used because some of the variations in properties are due to variations in chemical analysis within the specified ranges of those elements commonly specified and determined. Other variations in properties are due to variations in those constituents of steel (elements or compounds) that are not ordinarily included among the elements specified, thus not a part of the specified "composition." The term "constitution" is used to include not only the specified composition but also the nature and distribution of every element or compound contained in the steel entering the ingot mold; also included are items such as aluminum oxides and nitrides, presence of soluble gases, and dispersion of nonmetallic particles. When it is considered that the constitution of steel is determined by the addition or absorption into the bath of all such constituents from whatever source, it follows that constitution is of necessity the final result of steelmaking practice. It is the agency through which steelmaking practice operates to control the properties of the steel. The term steelmaking practice is here used in the broad sense, meaning the control of all the materials entering the steel and of the conditions under which the process is carried out. Steelmaking practice, thus defined, establishes the chemical system within which the reactions between components must proceed in obedience to the laws of chemistry. Thus the chemical constitution of the steel is established and, through constitution, the properties of the metal are established. In the preceding chapters it has been shown how the constitu-

Jan 1, 1951

By John Sasadi, Karl Heinz Zepter, Leonard Sugin, Roger L. Hulette

Mt. Newman Mining Co. is now completing an expansion program, begun even before initial construction was complete, which will result in the ability to ship up to 35 million tpy of iron ore by early 1973. Located in the Pilbara region of Western Australia, the mine at Mt. Whaleback is about 700 road miles north of Perth and 265 railroad miles south of the port facilities at Port Hedland. Development of the tertiary crushing and screening facilities best illustrates the orderly, but rapid, sequence through which the capacity of the port loading terminal has been expanded. When the present program is completed, crushing and shiploading capability will reach - - 35 million tpy. Operations commenced in 1969 with 3 crusher lines in service; and despite the 5-million annual ton rating, 6.46 million tons of ore were shipped during the first full year of operation. With continuing increase in ore sales, expansion to an annual capacity of 12 million tons was authorized, and installation of two more crusher lines was begun. As a part of this program, provision for installation of a sixth crusher at some future date was included in the planning; but before construction was completed, new ore sales contracts demanded further expansion to an annual rate of 20 million tons, and the sixth crusher line was authorized. The distributing and collecting conveyors had been designed for extension in length and increase in capacity, therefore, conveyor service was provided for the additional crushers with additional belting and hardware only.

Jan 6, 1972

By D. B. Robinson, C. A. Macrygeorgos, G. W. Govier

Experimental data have been obtained on the volurrletric behavior of ternary mixtures of methane, hydrogen sulfide and carbon dioxide at temperalures of 40°, 100" and 160°F up to pressures of 3,000 psia. The results indicate that the compressibility factors for this system do not agree with compressibility factors for sweet natural gases at the same pseudo-reduced conditions. The deviation increases as the temperature and methane content decrease. Discrepancies of up to 35 per cent were observed. A careful analysis has been made of the existing pUrblished data on compressibility factors for binary systems containing light hydrocnrbons and hydrogen sulfide or carbon dioxide. It has been found that the deviation of actual from predicted compressibility factors for methane-acid gas mixtures is a function of the methane content and the pseudo-critical properties,.v of the mixture. The ratio between actual compressibility factors for methane-acid gas mixtures and compressibility factors for sweet natrlral gases at the same pseudo-reduced conditions has been currelated over a range of pP,, from 0 to at least 7 arid a range of pT, from about 1.15 to at 1east 2 0 with an error not exceeding 3 per cent and over most of the range within I per cent. The validity of the correlation for mixtures containing appreciable hearvier hydrocorbons has not been fully established, but it is shown to be preferable than the use of a corretation based only on hydrocarbons. INTRODUCTION Although a relatively accurate method for predicting compressibility factors of pure materials is provided by charts based on reduced properties and the assumption that the compressibility factor is a unique function of T P and z the determination of the correct values of compressibility factors for gas mixtures is somewhat difficult. Two general methods of dealing with gaseous mixtures have been proposed. The first assumes a direct or modified additivity of certain properties of the mixture in terms of the properties of the individual components. Examples of this method are based on the familiar laws of Dalton and Amagat. The second method averages the constants of an equation of state applicable to the pure components. Both of these methods are of limited value in engineering calculations because the first usually provides reliable answers only over narrow ranges of pressure and temperature and the second is cumbersome to handle. In petroleum engineering practice accurate estimations of the volumetric behavior of natural gases arc frequently required. To fulfill this need, several generalized compressibility charts have been developed.' ' Of these, the one prepared by Standing, el al is widely used at present. In the construction of charts of this type a third method for dealing with mixtures has been followed. It is based on correlation of pseudo-critical properties as outlined by Kay and calculated from the critical properties of the individual components in a mixture. Although these charts provide relatively accurate information on the compressibility of dry or wet sweet natural gases, they are less reliable when used for gases containing high concentrations of hydrogen sulfide or carbon dioxide or both. Thus, an experimental program, although time consuming, is the best means now available for the determination of the volumetric behavior of sour or acid gas mixtures. An increased interest in the behavior of these gas mixtures, particularly in connection with some of the fields in Western Canada where the acid gas concentration of the reservoirs may be as high as 55 per cent and where hydrogen sulfide alone may be as high as 36 per cent, provided the incentive for this study. It was the purpose of the investigation to determine the volumetric behavior of selected mixtures of methane, hydrogen sulfide and carbon dioxide over a range of temperature from 40" to 160°F and at pressures up to 3,000 psi. EXPERIMENTAL METHOD The apparatus used in this investigation was basically the same as that described by Lorenzo.'" The amount of each pure component used in preparing the gas mixtures was measured over mercury in a glass-windowed pressure vessel. The pure components were then transferred individually in the desired amounts to a second glass-windowed pressure vessel where the volumetric behavior of the mixture was determined. Volume was varied by mercury injection or withdrawal. The capacity of the cell was about 125 cc. Temperatures in the cells were measured with copper-constantan thermocouples and a Leeds Northrup semi-

By Stephen Royce

[Stephen Royce.. I .......................... E. S. Moore.. 9 .......................... E. L. Bruce.. 10 ......................... J. E. Hawley.. 11 ........................ L. M. Scofield.. I 2] STEPHEN ROYCE, * Crystal Falls, Mich.Having examined and reported upon the Steep Rock Lake property and vicinity on several occasions for clients, and having kept in touch with the operation from 1938 on, the writer offers the following discussion of the valuable paper by Messrs. Roberts and Bartley, which was so kindly prepared in response to the writer's earnest request, made as a member of the Committee on Mining Geology. ORIGIN OF THE ORES The writer wishes to express complete agreement with the authors that the origin of these deposits was replacement action by hot ascending sulphide solutions of igneous origin, gaining access via the limestone and dolomite breccia channels, and acting mainly to replace the dolomite and limestone breccia with hematite and hydrated hematite. Some replacement in adjoining greenstones and tuffs by the same solutions may also have taken place, but the latter occurrences may represent replaced iron formations originally bedded in with the volcanics. Iron formation in the same relationship to volcanics is extensively developed on the western Menominee Range of Michigan, in the Middle Huronian belts; also appears in similar relations on the Vermilion Range; and is abundantly exposed in the same stratigraphic position no farther away than the southeast arm of Steep Rock Lake itself. Furthermore, the writer's classification of drill cores, made June 11, 1938, on the prop¬erty, contains the following, for hole 8, in the original strike of the A ore body: "332-342 ore; 342-350 much-leached sugary chert with thin ferruginous slate bands." This is a typical iron formation. The ore in this first group of holes (Numbers 6 to 13, incl.) is described in the writer's 1938 notes as follows: "The ore is hard, massive hematite with some limonite, and shot through with many small vugs." The breccia forms in the float ore and in the drill samples were also noted. As a field classification this does not check badly with Professor Schwartz's microscopic work. Notes supplied by Mr. Neeland, then geologist at the exploration, show: "Hole 23 has some iron formation, not logged yet." It appears therefore that there is some iron formation at the exploration, much iron formation in similar stratigraphic position in the vicinity, and iron formation similarly located as to volcanics on the Vermilion and western Menominee Ranges. Certain of the holes, notably Holes 25 and 27, showed some specular hematites resembling those known to be formed from cherty iron formation elsewhere. Hence the writer concludes that at least a small part of the Steep Rock ores results from replacement of iron formation. By far the greater part of it is, as the authors say, clearly a replaced limestone and dolomite breccia, with the breccia outlines still preserved in much of the ore, and all of the replacement is by hot ascending waters. The authors' citation of the neighboring Atikokan pyrite, pyrrhotite and magnetite

Jan 1, 1943