Search Documents

By Joseph L. Gillson

Bentonite, designating a distinct type of clay, is a young name in mineral nomenclature in the light of the age-old names of most other useful nonmetallics. The earliest references in literature are to "soap clay" (1873) "taylorite" (1888) and finally "bentonite" in 1897, from its occurrence in the Fort Benton series of rocks near Rock Creek, Albany County, Wyoming. Bentonite is a rock term and consists largely of montmorillonite clay. The latter name was proposed in 1847 for a plastic clay found at Montmorillon, France. A clay of apparently identical properties was described by Cronstedt of Sweden in 1788 and a number of other similar clays found in France were given other names in publications from 1853 to 1856. The mineral name montmorillonite was recognized by Dana in 1892. The recognition of "clay mineral" distinctions which led to the present-day classifications of clays by their chief mineral content, dawned in the early part of the twentieth century. Grim6 has aptly said: About 1924, Ross10 and some colleagues of the U. S. Geological Survey began a study of the mineral composition of clays that led to a series of monumental papers on the subject. By the early 1930's what has come to be known as the clay-mineral concept became firmly established in the minds of a great many people actively studying clay materials. The clay mineral concept designates the major clays as kaolins, montmorillonites and illites and by this concept bentonites are now defined as "fine-grained clays containing not less than 85 pct montmorillonite" and a wide variety of clays found all over the world are included in that classification. They could all properly be called "montmorillonite clays" but the common commercial name is bentonite. For a period of over forty years from the time of the earlier discoveries, bentonite was thought to be only the sodium type highswelling clay produced principally in Wyoming. By the clay mineral concept, non-swelling montmorillonite clays also became known as bentonite. In the trade there are two broad divisions-sodium bentonite, often called Wyoming or "western," which expands in water and carries sodium as its predominant exchangeable ion, and calcium bentonite often called "southern," which has negligible swelling and carries calcium as its principal exchangeable ion. There are many intermediate gradations. Properties The mineralogy and chemistry of the clays are so complex that the subject cannot be summarized briefly. The reader is referred to Chapter 12 of this volume in which the subject is treated at some length. Grim6 gave the formula for montmorillonite as (OH)4Si8AL4020.nH2O. He wrote: Montmorillonite is composed of units made up of two silica tetrahedral sheets with a central alumina octahedral sheet. . . . Exchangeable rations occur between the silicate layers. . . . The words "tetrahedral" and "octahedral" refer to the coordination number of the cations in the unit cell in the crystallographic lattice. Carroll5a stated: That the montmorillonite structure is the same as that of mica, but the layers are not held together by K+ ions; and water and other polar molecules, such as organic molecules, can enter between the unit layers and cause expansion. Ex-

Jan 1, 1960

By T. C. Boberg, R. B. Lantz

This paper presents a method for calculating the producing rate of a well as a function of time following steam stimulation. The calculations have proved valuable in both selecting wells for stimulation and in determining optimum treatment sizes. The heat transfer model accounts for cooling of the oil sand by both vertical and radial conduction. Heat losses for any number of productive sands separated by unproductive rock are calculated for the injection. shut-in and production phases of the cycle. The oil rate increase caused by viscosity reduction due to heating is calculated by steady-state radial flow equations. The response of successive cycles of steam injection can also be calculated with this method. Excellent agreement is shown between calculated and actual field results. Also included are the results of several reservoir and process variable studies. The method is best suited for wells producing from a multiplicity of thin sands where the bulk of the stimulated production comes from the unheated reservoir. The flow equations used neglect gravity drainage and saturation changes within the heated region. INTRODUCTION This paper presents a calculation method which can be used to predict the field performance of the cyclic steam stimulation process. The calculation method enables the engineer to select reservoirs that have favorable characteristics for steam stimulation and permits him to determine how much steam must be injected to achieve favorable stimulation. While the calculation represents a considerable simplification of physical reality and the results are subject to numerous assumptions which must be made about the reservoir, it has been found that realistic calculations can be made of individual well performance following steam injection. The duration of the stimulation effect will depend primarily on the rate at which the heated oil sand cools which, in turn, is determined by the rate at which energy is removed from the formation with the produced fluids and conducted from the heated oil sand to unproductive rock. A complete mathematical solution to this problem is a formidable task, and finite difference techniques would undoubtedly have to be used. The calculation method pre- sented here utilizes analytic solutions of simple related heat transfer and fluid flow problems. The method is sufficiently simplified that it can be used as a hand calculation, although the calculations are somewhat lengthy and laborious. For that reason, the analysis was programmed for an IBM 7044 digital computer. Well responses observed at the Quiriquire field in eastern Venezuela&apos; have been matched using this program after making suitable approximations for reservoir and wellbore conditions. One of the most valuable uses of this calculation method is to assess the effect of reservoir and proc-cess variables on the stimulation response. This paper contains results of several studies made of key reservoir and process parameters. Among the most important of these is the influence of prior wellbore permeability damage. If a well is severely damaged prior to stimulation, a higher stimulation response will be observed than if it is undamaged. If a portion of this damage is removed, a permanent rate improvement will occur. THEORY I)ES(:KJJ&apos;TION OF CALCULATION METHOD The process of cyclic steam stimulation is essentially one of reducing oil viscosity around the wellbore by heating for a limited distance out into the formation through the injection of steam. Suitable modifications of the calculation technique presented here can be made so that stimulation of wells by hot gas injection or in situ combustion can also be calculated. A schematic drawing of the heat transfer and fluid flow considerations included in the calculation method is shown in Fig. 1. In brief, the calculation assumes that the oil sand is uniformly and radially invaded by injected steam. For wells producing from several sands, each sand is assumed to be invaded to the same distance radially. In calculating the radius heated rn energy losses from the wellbore and conduction to impermeable rock adjacent to the producing sands are taken into account. After steam injection is stopped, heat conduction continues and oil sands with r < ra cool as previously unheated shale and oil sand at r > r, begin to warm. The effect of warming of oil sand out beyond r, has little effect on the oil production rate compared to the effect of cooling of the oil sand nearer the wellbore than ra. Thus, in computing the oil production rate, an idealized step function temperature distribution in the reservoir is assumed where the original temperature exists for r > rn and where an average elevated temperature exists for r < rn. The average temperature in the oil sand for the region r < rn is computed as a function of

Jan 1, 1967

By Samuel Daniels

The Al-Cu-Ni-Mg alloy is much benefited by heat treatment and, in such condition, is preferable to the Al-Cu-Fe-Mg alloy either as cast or as heat-treated, when both are reheated to temperatures of from 400" to 600" F. and compared, cold, with respect to strength and to hardness. The main differences between the alloys do not arise until the reheating temperature exceeds 400" F., above which they gradually soften. This softening is characterized metallographically by the appearance of intragranular precipitate. The Al-Cu-Ni-Mg alloy is weakest and least hard after being reheated at 600" F., the Al-Cu-Fe-Mg alloy at about 700" F. The former starts to reharden at 700" F., the latter at 800&apos; F. There is a tendency for both alloys to lose strength and hardness with prolongation of time at the reheating temperatures of 500" and of 700" F. The Al-Cu-Ni-Mg alloy is considerably stronger and harder than the Al-Cu-Fe-Mg alloy when both are heat-treated and reheated for long periods of time at 500" and 700" F. Although the latter can be made harder initially than the Al-Cu-Ni-Mg alloy by suitable quenching and aging, heat treatment, in general, favors the retention of this initial (strength and) hardness after reheating to a much greater degree in the Al-Cu-Ni-Mg alloy. The percentage of elongation of the two materials in any condition is very small. Certain aluminum alloys have been used for pistons and other parts operating at temperatures up to 650" F. because of their lightness, high thermal conductivity and specific heat, fair strength and hardness at elevated temperatures, excellent machineability, and moderate resistance to corrosion. In the piston, the inertia forces and the bearing loading, and with this the vibration, are decreased. The piston head functions at a lower temperature (about 200" F. below one of cast iron), so that, because of the lessened tendency toward carbonization and detonation, higher compression ratios may be used. On the other hand, the aluminum alloys do not have the wearing and bearing qualities of cast iron; also they have a large coefficient of expansion, allowance for which must be made in the design. The range in analyses of aluminum alloys, used for pistons in domestic and in foreign internal-combustion engines is shown in Table 1. There seem to be three general types of composition; one containing about 10

Jan 1, 1926

By Frank C. Roberts

Progress in the facilities for handling mining products has been largely superinduced by the necessities of commercial economy ren dered requisite in order to meet the demand of competition. So rapid has been the depreciation in the value of mineral products, primarily due to the disproportionate increase of output over con sumption, that it may be justly claimed that mining, when considered as a commercial success, depends largely upon the ease and cheap ness by which the products are brought to the surface of the ground. In all methods of performing this operation, wire rope enters as an important factor; and the object of the present sketch will be to explain, as fully as is consistent with the space allotted, the various • adaptations of wire rope employed in placing coal and ores within the reach of our overground systems of transportation. These adaptations will be considered in the following order: I. Hoists. II. Inclined planes. a. Engine planes. b. Gravity planes. c. Aerial planes. III. Haulage. a. Tail-rope system. b. Counter-rope system. c. Endless-rope system. IV. Hoists. The term " hoist" is applied to the system whereby the mine product is elevated from the mine-level to the surface through ver-

Jan 1, 1888

By D. W. G. White

The surface tension of zinc has been determined by the sessile-drop method in a progvam emphaszzing detailed experimental care. The surface tension oj. the pure metal was measured over a range of ternperature from the melting point (419.6"C) to 540°C. At the melting point, the suvface tension of zinc was found to be: 1) 99.99+ pct Zn - 757.0 5 dynes per cm 2) 99.999+ pct Zn - 761.0 5 dynes per CI 3) 99.9999 pct Zn - 76&apos;7.5 5 dynes pev cna From experiments carried out in a closed, isothermal cell, the temperatuve coejyicient of the surface tension (6y/6T)p, , of zinc xas found not to be negative but to be postiue. A positive tenzperatre coefficient indicates a greater depee of order in the surface than in the body of the lquid. Houlezer, by delibevately inducing continuous zaporization, a temperature coefficient of su)face tension with a negative slope can be produced. The work reported herein was undertaken as part of a larger program of fundamental research on the properties of molten zinc and zinc alloys. This program grew out of a continuing interest at the Mines Branch in the behavior of liquid metals in the foundry and of a desire on the part of the zinc industry for reliable basic data. The work was originally begun in cooperation with the Consolidated Mining and Smelting Co. Ltd., Trail, B.C., and was subsequently continued from 1960 to date in association with the Canadian Zinc and Lead Research Committee and the International Lead and Zinc Research Organization. Although the surface tension of liquid zinc has of course, been measured before, as Table I and Fig. 1 demonstrate, there is not good agreement among the existing values. Such disparities arise because sources of experimental error are insufficiently controlled. This situation places the reader in doubt. One result may be correct within narrow limits—even fortuitously—yet, because there is not agreement between several values, none can be accepted with conviction and all become suspect. It seemed, therefore, in the circumstances, that there was room for further work embodying considerable emphasis on experimental care in order that, within a small margin of error, an accurate value might be obtained. It was in this spirit that the work was undertaken. METHOD The sessile-drop method -as adopted for this work. In this method, when applied to liquid metals at elevated temperatures, the outline of the meridional section through a drop resting freely on a horizontal surface is recorded photographically. Certain parameters

Jan 1, 1967

By Gary E. Melickian

Last year&apos;s review was characterized as a year of politics and began an era of legislation. The 1972 review can be similarly characterized, with even more rigid health and safety regulations and environmental legislation. The mining industry should be aware of what&apos;s happening in the nuclear power and other fields as a result of the National Environmental Policy Act (NEPA) of 1969, where the environmental impact of most major construction activities are already under close scrutiny. Section 102 of NEPA requires that all federal agencies include a detailed statement on specified environmental conditions as part of every report on proposed actions significantly affecting the quality of the human environment. All such environmental reports must consider the same general conditions: • The environmental impact of the proposed action. • Any adverse environmental effects which cannot be avoided should the proposal be implemented. • Alternatives to the proposed action. • The relationship between local short-term uses of man&apos;s environment and the maintenance and enhancement of long-term productivity. • Any irreversible and irretrievable commitments of resources which would be involved in the proposed action should it be implemented.

Jan 2, 1973

By P. L. Hendricks, J. W. Spretnak

The interstitial atom principally responsible for the yield point and strain aging in electron-beam-melted tantalum is identified by analysis of the kinetics of the return of the yield point after an increment of plastic deformation. Two sets of specimens contained two levels of oxygen with very low hydrogen contents and the third set had comparable oxygen and hydrogen contents. The activation energy for the return of the yield point agrees well with that for diffusion of oxygen for the first two sets of specimens. For the third set of specimens, the activation-energy value lies between those for diffusion of hydrogen and for diffusion of oxygen. The advent of the dislocation model of plastic deformation in metals has revitalized interest in the yield point and strain aging in bcc metals containing a certain minimum content of interstitial solute elements. Much theoretical and experimental work has been performed in recent years to elucidate the detailed mechanism of these phenomena. The purpose of this investigation is to attempt to identify the principal interstitial element responsible for the yield-point phenomenon in electron-beam-melted tantalum by analysis of the kinetics of the return of the yield point after an increment of plastic deformation. Some of the earlier theories of the yield-point phenomenon proposed a grain boundary film of iron carbide. Such models could not satisfactorily explain all features of strain aging and the yield-point phenomena. The most widely accepted explanation is that of Cottrell,1 later extended by Cottrell and Bilby.2 Strain aging is ascribed to "locking" of dislocations by interstitial solute "atmospheres". The yield-point phenomenon results when the dislocations are torn away from their atmospheres. The strain-aged condition is re-established after sufficient time to allow the interstitial atoms to diffuse to the dislocation lines and re-establish the locking atmospheres. Clearly, the Cottrell-Bilby model is concerned with the bulk of the grain and does not specifically involve the grain boundary. The recent modification of the Cottrell-Bilby model is a redirection of attention to the role of the grain boundary and the possibility of multiplication of a limited number of free dislocations rather than unlocking all of the dislocations. Theories have been advanced by Hahn3 and conrad4 which are modifications of the Cottrell-Bilby theory. The model proposed by Hahn indicates that, although the possibility of un- locking anchored dislocations is not excluded, it implies that unlocking is not necessarily required to explain yield drop. Locking of dislocations during the aging treatment is a necessary part of the theory; however, it assumes that dislocations once locked remain locked. It is suggested that the yield drop observed is a result of the following factors: 1) the presence of a small number of mobile dislocations initially, 2) rapid dislocation multiplication, 3) the stress dependence of dislocation velocity. In the case of bcc metals, locking is considered to be the means by which dislocations are immobilized. Cold working of the metal results in the generation of larger numbers of new dislocations and the stress dependence of the dislocation velocity accounts for yield drop observed. Conrad&apos; has proposed a model similar to the one just described which applies to strain aging of iron and steel and which logically could be extended to other bcc metals. This model also does not require large-scale unlocking of dislocations. It is proposed that, during initial loading of a specimen below the upper yield stress, a few dislocations are torn free of their Cottrell atmospheres at regions of stress concentrations. With an increasing stress, some multiplication of dislocations occurs by a double cross slip mechanism, thus giving a preyield microstrain. At some critical stress represented by the upper yield stress, sudden profuse multiplication of dislocations occurs, enabling plastic flow to proceed at a lower stress. In this model, microstrain, preyielding, and flow represent the movement of free dislocations. It should be noted that this model also requires the locking of dislocations by interstitial solute atoms for the occurrence of a yield point; however, unlocking of large numbers of dislocations is not required. If it is assumed that the yield point will return when some fraction of free dislocations produced during pre-straining are pinned, the number of solute atoms required to pin unit length of a dislocation line can be calculated when prestrain and reloading are done at the same temperature and strain rate. Since the migration of solute atoms back to the stress fields of dislocation lines is controlled by the diffusion rate of interstitial solute atoms, it is to be expected that the activation energy for strain aging would be identical to the activation energy for diffusion. It would also be expected that the strain aging observed will be controlled by the fastest diffusing species capable of producing locking over the temperature range investigated. The rate of yield-point return has been found to be adequately expressed by an empirical rate equation of the form: rate=Ae-Q/RT [1] where A = constant, Q = activation energy, R = gas constant, and T = absolute temperature. Cottrell and Bilby2 have expressed the number of atoms per unit length of dislocation line which arrive

Jan 1, 1967

By Robert E. Green

Formulae are given for calculating the modes of wave propagation in a single-crystdl specimen possessing a given crystallographic orientation. Such calculations lead to determination of the orientation factor appearing in the Granato-Lucke theory for the attenuation of these waves due to dislocation damping. A detailed treatment is given for the case of an aluminum crystal possessing the orientation having a maximum Schmid fac -tor of 0.5. FOR a number of years the attenuation of ultrasonic waves propagating in metals has been used to investigate various phenomena causing internal friction.Most of the experiments were performed on polycrystalline test specimens and the waves were assumed to be propagating in an isotopic medium. However Alers 6 in 1955 and more recently Hikata et at. Chiao and Gordon,8 and Swanson and Green 10 have used measurements of attenuation of ultrasonic waves to study internal-friction changes in single crystals. These authors were concerned with the energy losses experienced by the ultrasonic waves due to dislocation motion induced by plastic deformation of the crystals. Alers measured the attenuation of 7 mc per sec ultrasonic pulses propagating in zinc single crystals before, during, and after plastic deformation. Simultaneously he measured the time-dependent plastic strain at constant stress in order to study the correlation between this strain and attenuation. The crystals were oriented in such a way that the applied stress provided a direct shear on the slip plane, thus causing the deformation to proceed by slip on this plane. At the same time the high-frequency sound pulses were sent through the crystal perpendicular to the slip plane. He found that the attenuation of transverse waves, the stress vectors of which lie in the slip plane, was very sensitive to the deformation. The polarization of the particle displacements, associated with these waves, relative to the applied static shear stress, and hence the direction of slip, had no obvious effect on the results. The attenuation of longitudinal waves was affected by the deformation only when the slip plane was not perpendicular to the propagation direction. This indicated that the attenuation was caused by dislocations introduced by the deformation and moving only in the slip plane. Hikata et al. made simultaneous measurements of attenuation, velocity changes, and stress-strain relations on aluminum single crystals deformed in tension. Both longitudinal and shear waves were used, at frequencies of 10 and 13 mc per sec. They placed emphasis on the choice of propagation modes and polarization of the ultrasonic waves, such that interactions between these waves and dislocations on selected slip systems could be investigated. They also selected specimens possessing specific crys-tallographic orientations, which allowed investigation as a function of the number of equally favored slip systems under the applied stress. They found that, for symmetrical orientations, the change of attenuation decreases with the increasing number of equally favored slip systems, i.e., in the order

Jan 1, 1964

By E. E. Donath

THE coal hydrogenation process is well known as a means for the production of liquid fuels -from coal. In this paper the possibilities of the coal hydrogenation process as a source of chemical raw materials will be discussed. The recovery of chemicals from coal hydrogenation products necessitates some modifications and additions to the equipment used for the production of fuels. The conversion of coal into liquid fuels such as gasoline requires two steps: liquid phase and vapor phase hydrogenation. Intermediate oils obtained in the liquid phase contain oxygen and nitrogen compounds, especially aromatic compounds, since the coal itself is composed mainly of cyclic compounds. These oils are the raw material for the separation of high molecular weight aromatics and of tar acids and tar bases. The relative amounts of heavy and middle oil-boiling above and below, e.g., 325°C-can be influenced by temperature, residence time, and catalyst of the liquid phase hydrogenation. In the vapor phase hydrogenation a solid bed catalyst is used to convert the intermediate oil from the liquid phase operation into hydrocarbons of the gasoline boiling range. Essentially pure hydrocarbons with a low content of sulphur, oxygen, nitrogen, and olefines are obtained. Depending mainly on the catalyst, the high ring compound content of the liquid phase oil can be preserved and gasoline rich in aromatics obtained. However, with other catalysts, these ring compounds can be split into gasoline with a high content of isoparaffins.1 Again, depending on the operating conditions, products of varying boiling range can be obtained. Selection of catalyst and operating conditions therefore makes possible the production of different grades of motor fuel and also variations in the relative amounts of benzene, toluene, and xylene when aromatic hydrocarbons are produced. The schematic flowsheet, Fig. 1, shows the main steps of the coal hydrogenation process, and the product streams used for the recovery of chemicals are indicated. In the liquid phase hydrogenation stage, coal is made into a paste with recycle heavy oil. The coal paste is mixed with hydrogen and preheated at a pressure of 300 to 700 atm in heat exchangers and preheaters. The coal paste and hydro¬gen enter high pressure converters where the liquefaction of coal, conversion of the high boiling liquid materials initially obtained, into intermediate oils is performed at a temperature around 470°C. The reaction products enter the hot catchpot in which lower boiling oil vapors are separated from the residue containing unreacted coal, ash, and heavy oil. This residue, usually called H.O.L.D. (heavy oil let down), is processed to separate solid and liquid material. By thermal treatment of the residue, e.g., a coking process, distillate oil is obtained, which can be recycled as part of the pasting oil. This stream is rich in polynuclear aromatics and can be, and has been, used for the recovery of such material. The oil vapors and hydrogen from the hot catch-pot are cooled in heat exchangers and a cooler, and the condensed oil is separated from the recycle hy-

Jan 1, 1952

By C. E. Jackson, E. C. Nelson, A. L. Christenson

Much information regarding the transfornlatio~lal characteristics of a steel as it cools in a known manner from the austenitic state can be obtained from dilatometric studies. This method has received more arid more attention because of its great flexibility, accuracy, and ease of interpretation. &apos;The method is entirely applicable to any rate of heating and cooling although the experumental procrdures for high rates of cooling have offered some difficulties. This paper presents a description of equipment employing cooling rates up to 500 °C. per secorld and the results of dilatometric observations on six commercial steels are included. French and Klopsch1 studied the cooling transformations of a serirs OF carbon steel, using the thermal arrest method. This was followed by the systematic investigatiol1 of Esser and co-workers on the effect of carhon2 and other alloying additions. in which the transforlnation temperature\ were determined by magnetic induction measurements indicated by a string galranoineter. Emphasis was placed on determining Ar&apos; trailsformations and the critical cooling rates for these steels. The maglietic measurements wrere used in an effort to obtain more accurate data at higher cooling rates. Measurements of thermal arrest were made also to check the validity of the magnetic indications, and good correlation was found between the two, although Esser&apos;s,Ar&apos; temperature measurements on iron-carbon alloys were about 200°F. lower than the measurements made by Fresnch and Klopsch. A notable contril~ution by Esser was the introduction gas quenching. wever and Rose4 used a moving-coil galranometcr in the study of the .Ar and Ar" of iron-carbon alloys by the thermal arrest method and obtained somewhat lover Ar" temperatures than those observed by Esser below I per cent carbon and considerably higher ahove. They concluded that the cooling rate had little influcncc on the Ar" temperatures above 0.4 per cent carbon, although Esser had observed a decrease in the -4r" temperature with increasing cooling rate with similar steels. Digges determined the .Ar" temperature4 for a scries of high-purity iron-carbon alloys, and close agreement with his results was obtained by Greninger. The thermal arrest method. together with metallographic observation used in both these studies, represents the latest investigations of this type. Any investigation by thermal analyses is dependent on the heat of reaction and the specific heat of the

Jan 1, 1945

By P. N. Richards, M. K. Ormay

Commercially hot-rolled low-carbon steel strip may have one of two basic types of orientation texture, depending upon the amount of a iron which was present during the finishing passes. The changes in these textures with varying amounts of cold reduction up to 95 pct have been determined for the sheet surface plane and for parallel planes down to the mid-plane. The development of cold reduction textures has been reassessed on the basis of (200), (222). and (110) stereographic pole figures and pole density or inverse pole figure values. In agreement with the literature, it is shown that the textures can be described in terms of partial fiber textures but alternative descriptions are given for one of the fiber textures, in order to more closely correlate with experimental data. One partial fiber texture consists of orientations of the type (hkk)[011] extending from (100)[011] to {322}(011) in agreement with the literature. At moderate amounts of cold reduction, a second partial fiber texture forms with a <331> fiber axis inclined 20 deg to the sheet normal and a range of orientations centered on one close to (1 11)[112] and reaching to (232)[101] or (322)[011]. An alternative description involves a (111) fiber axis parallel to the sheet normal but capable of rotation about the rolling direction with rotation about the fiber axis. ORIENTATIONS developed in low-carbon steel strip after cold reduction are of commercial importance because they control, in part, the final preferred orientations after subsequent annealing. The method of control however is not understood completely. Some preliminary work indicated that the cold-reduced orientations and the subsequent annealing textures of commercial low-carbon steel were dependent on the orientations present in the material before cold reduction, that is, those present in the hot-rolled strip but, to date, the effects of initial orientations have not been extensively investigated. For this reason, much of the information given in the literature on development of preferred orientation is difficult to assess as details of initial texture and processing conditions are often inadequate or are altered by a subsequent heat treatment such as normalizing.&apos; It is known2 that anomalous results for near surface orientations may be obtained if lubrication during cold rolling is not adequate but whether lubricant was used during the experiments has not always been given, nor has the exact depth below the surface at which determinations have been made. A comprehensive review of cold rolling textures has been made recently by Dillamore and Roberts&apos; and more restricted recent reviews are due to stickels4 and Abe.5 Based largely on the experimental work of Bennewitz,1 reviewers have accepted that the preferred orientations produced on cold reducing low-carbon steel can be described in terms of two partial fiber textures as follows: Partial Fiber Texture A which has a (011) direction in the rolling direction and includes orientations within the spread from (211)[011] through (100)[Oll] to (211)[011.]; there is some controversy as to whether it extends as far as the orientation (111)[011]. As Dillamore6 has observed, the extent of this partial fiber texture depends on the intensity levels selected. Partial Fiber -texture B which has a (011) direction located 60 den from the rolling direction in the plane containing the rolling direction and the sheet normal. There are two directions which satisfy these conditions and orientations in this partial fiber texture extend from (21l)[0ll] through (554)[225] to (121)[101]. The orientations {211}(011) are members of both partial fiber textures A and B and it can be noted that a variant of {554)<225> is within 6 deg of a variant of {111}(112). Barrett7 had postulated earlier that, in addition to orientations which would fall into partial fiber texture A, a true fiber texture with a (111) direction in the sheet normal was present after heavy cold reduction. This fiber texture would include orientations such as {111}(011) and {111}(112). Later investigators, notably Bennewitz,&apos; have discounted this, mostly on the ground that the partial fiber textures A and B, as described above, contain all the strong orientations that have been observed. However in other work it has been reported2 that (222) pole density or inverse pole figure values show a continuing increase with increasing reduction by cold rolling and give values considerably greater than for any other low indices plane. Thus it could be inferred that a (111) fiber texture as described by Barrett would be one which becomes more dominant with increasing cold reduction, whereas Bennewitz&apos; concluded that components such as {554)(225) in partial fiber texture B began to decrease in intensity at high reductions. Following Bennewitz, one would expect a decreasing (222) pole density value (parallel to the sheet normal) with increasing cold reduction. Because fiber textures consist of grains with a range of orientations that have one axis in common, it has been inferred that during deformation the crystal orientations rotate about the fiber axis&apos;74 and that the orientations of crystals that at one stage belong to one fiber texture can rotate on further cold reduction into the other fiber texture through an orientation in which the two fiber textures intersect.&apos; For example,

Jan 1, 1970

Jan 1, 1938

By F. H. Vitovec, D. W. Hoeppner

Pusk-pull fatigue tests were conducted on copper tricrystals of 99.988 pct purity to ascertain the role of grain boundaries in the initiation and propagation of fatigue cracks. Significant differences in behavior were found for specimens which possessed different transverse-boundary misorientation. In speciwens with low boundary angles cracks initiated within the transverse boundary, while higher angles led to transcrystalline fatigue failure. It is suggested that at low angular misorientation moving dislocations may interact with dislocations of the boundary or dislocations present in adjacent pains on favorably oriented glide planes, thus initiating a fatigue crack. MANY fatigue studies have been concerned with fatigue-crack initiation within grains and the mechanism causing initiation and propagation1-3 Although the initiation of fatigue cracks in or near grain boundaries of pure metals has been observed and reported in the literature, the mechanism of this phenomenon has received little attention.4"11 EXPERIMENTAL PROGRAM Testing Procedure. To investigate the role of grain boundaries regarding initiation and propagation of fatigue cracks, copper tricrystals were tested in push-pull. Axial-stress tests were used to avoid the stress gradients introduced by stressing of some other nature. Copper was selected as the most suitable test material since extensive work has been done on the formation of fatigue-induced slip in copper. Tricrystal specimens were used to provide a grain boundary geometry with one boundary transverse to the principal stress axis and one or more boundaries nearly coincident with the direction of maximum resolved shear stress. The boundary energy and the slip characteristics in the vicinity of the transverse boundary depend on the relative orientations of grains across the boundary. Testing was done at room temperature, at a frequency of 700 cpm, in an atmosphere of either air or argon. It is known that the incidence of grain boundary cracking increases with increasing temperature and decreasing frequency.4 The fatigue machine applied a uniaxial tension-compression load to the specimen by a flat spring which was actuated by an adjustable eccentric. Use was made of an adjustable head and a load cell which had strain gages mounted at 120-deg intervals around its periphery, thus providing a means for eliminating any detectable superimposed bending moment. A clip gage was mounted between the gripping heads to record the cyclic strain amplitude applied to the specimen. Each specimen&apos;s hysteresis characteristics were recorded by supplying the load and strain signals to an oscilloscope. Microstructural changes were observed and recorded with an optical microscope which was mounted on the fatigue machine. Immediately prior to insertion in the machine, each specimen was chemically polished. Extreme care was exercised while inserting the specimen in the test machine to avoid either bending the specimen or introducing a mean load. Each specimen was stressed in the tensile direction first and subsequently the load was reversed. Specimen Preparation. Tricrystal fatigue specimens of 99.988 pct Cu were grown from the melt using a modified Bridgman technique. Ingots about 1 in. high were grown to the configuration shown in Fig. 1. Upon sectioning the resultant ingot, several specimens were provided with an identical shape and grain boundary orientation. Except for plane sectioning and final polishing, this method eliminated machining the specimens. The apparatus used for growing the tricrystals is shown in Fig. 2. A spectrographically pure graphite mold, Fig. 3, was inserted in a vycor tube which was mounted on a vertical zone-refining table. Prior to insertion in the tube the mold was assembled as follows. The insert and graphite rods were fixed in position in the mold. The copper was then placed in the mold and the entire mold assembly was positioned in the vycor tube, Fig. 2. At this point the tube was sealed, evacuated, purged with helium gas, and finally placed under a slightly positive helium pressure. The heating coil was then adjusted to melt the copper charge, after which it was raised at a speed of 4 in. per hr. It is also possible to use

Jan 1, 1964

By Arthur Gibson

Synopsis.-A new feature in coal mining, where the coal is to be conveyed from a high to a lower elevation and the topography of the country is such as to preclude surface haulage. The distance from the mine to the tipple inn this instance is about 3,000 ft. and the difference in elevation between the terminals 321 ft., of which 225 ft. occurs in the first 1,300 ft. from the loading terminal. A mine car was designed especially for this plant consisting of two tramway buckets on one pair of trucks, the buckets being lifted from the truck, attached to the train line automatically, and conveyed to the tipple. THROUGHOUT eastern Utah, in the Book Cliff range and the Wasatch plateau, the coal-bearing measures are admirably exposed, in the bold and for the most part bare escarpments. The geology is simple, the rocks being almost flat, or at the most dipping not more than 10 per cent. The coal beds occur in a formation, or group of strata, consisting of sandstone and shale, 600 to 800 ft. thick, which has been correlated with the Mesaverde formation of the Cretaceous. Above this occurs about 2,000 ft. of alternate layers of buff-colored sandstone and shale. Below the coal lie the Colorado shales, which are estimated to be about 1,500 ft. thick, below which are the red rocks of the Jura-Trias. As a rule the coal beds all clip in a northerly direction and under the high mountain. The canyons opening out into what is known as Castle valley all cut the coal beds, and the beds rising in the direction of the valley are found frequently high up on the escarpment, often as much as 1,000 ft. above the valley. The surface features of the region have an economic bearing on the availability of the coal. The valleys and gulches in the Colorado shale extend out from the coal areas across the edge of the plain, so that it is impracticable to build transportation lines parallel with the boundaries of the field within several miles of the coal land. It will be necessary, therefore, to build branch lines up to the coal lands from points on the Denver & Rio Grande Railroad traversing Castle valley.

Jan 10, 1914

By Edward W. Parker

At the Seventy-sixth meeting of the Institute, held in New York, N. Y., February, 1899,I presented a paper on this subject entitled, Coal-Cutting Machinery,&apos; which has become somewhat out of date, in view of the decade&apos;s development in this feature of the coal-mining industry. It should be explained that the present paper is limited to the use of mining-machines in bituminous mines. Practically all of the anthracite mined is "shot from the solid," no undercutting being done. Anthracite-mining is therefore not considered in the statistics or other references. The statistical record as compiled by the U. S. Geological Survey shows that in 1898, the year preceding the presentation of my former paper, there were 32,413,144 short tons of coal undercut by the use of machines. In 1907 the machine-mined coal-product amounted to 138,547,823 short tons. In sympathy with the general decrease in coal-production during 1908, the output of machine-mined coal decreased to 123,183,334 short tons, but the proportion of machine-mined coal to the total output, nevertheless, showed an increase, from 35.1 per cent. in 1907 to 37 per cent. in 1908. In 1898 only 19.5 per cent. of the total product was unclercut.by the use of machines. The number of in use in the bituminous mines of the United States has increased from 2,622 in 1898 to 11,144 in 1907, and to 11,569 in 1908. The total production of bituminous coal in the United States in 1908 mas almost exactly double that of 1898, while the machine-

Jan 1, 1911

By Paul Billingsley, Augustus Locke

Certain adequately developed mining districts give complete three-dimensional patterns of ore bodies as clusters rising from roots in basement rocks with details controlled by structure of cover rocks. Examples are Goodsprings, Tintic, Bisbee, Leadville, Hedley, Eureka, Ely and Goldfield. In these and others the controlling structures in both basement and cover rock are elements of the neighboring regional structure and have been produced by rock movements in harmony with continental adjustments, which are usually steep tear faults in basement and thrust crumples in cover. Invariably the structures and movements in the districts have long geologic history and result from intersecting or superimposed deformations of different ages. Salt Lake districts show intersecting Uinta and Cordilleran elements; Colorado districts show intersecting pre-Cambrian and Tertiary elements, and Bisbee shows Tertiary superimposed on fina1 Paleozoic folding. Thus the position of districts has been determined by the patterns of North American orogenic belts, which make crossroads in Rocky Mountains and blocks of superimposed deformation in Sierra Nevada, northwest Coastand Canadian Coast Ranges. Essential function of repeated deformation is to strengthen rock, as from shale to slate to schist to gneiss, and thus make it competent to carry channels to depth with or without addition of intrusives. The essence of a mining district is the presence of such competent rocks with long-lived, deep, penetrating breaks reopened to permit passage of heat and associated products from depths to surface. It is suggested that melts such as magmas; metamorphism up to and including granitization; alteration, such as orthoclase-quartz or quartz-sericite or garnet, and also mineralization, may all be by-products of such heat escape along channels made by tectonic forces at specific foci. Magnitudes of Districts (Fig. 1) Any synthesis of ore deposits must deal with comparable units. Ore deposits are innumerable, but great ore deposits, commercially important for a generation or more, are few. The bulk of metals has come from districts of the first and second magnitudes (over $1,000,000,000 and over $250,000,000, respectively), and of these the United States and adjacent provinces of Canada and Mexico contain only 28, of which 9 are first magnitude: Butte, Coeur d&apos;Alene, Bingham, Bisbee, Sierra Gold, in the West; Tri-State, Southeast Missouri, Michigan copper, Sud-bury, in the East. Another 28 or 30 districts are of third magnitude (over $50,000,000).

Jan 1, 1941

By Augustus Locke, Paul Billingsley

Certain adequately developed mining districts give complete three-dimensional patterns of ore bodies as clusters rising from roots in basement rocks with details controlled by structure of cover rocks. Examples are Goodsprings, Tintic, Bisbee, Leadville, Hedley, Eureka, Ely and Goldfield. In these and others the controlling structures in both basement and cover rock are elements of the neighboring regional structure and have been produced by rock movements in harmony with continental adjustments, which are usually steep tear faults in basement and thrust crumples in cover. Invariably the structures and movements in the districts have long geologic history and result from intersecting or superimposed deformations of different ages. Salt Lake districts show intersecting Uinta and Cordilleran elements; Colorado districts show intersecting pre-Cambrian and Tertiary elements, and Bisbee shows Tertiary superimposed on fina1 Paleozoic folding. Thus the position of districts has been determined by the patterns of North American orogenic belts, which make crossroads in Rocky Mountains and blocks of superimposed deformation in Sierra Nevada, northwest Coastand Canadian Coast Ranges. Essential function of repeated deformation is to strengthen rock, as from shale to slate to schist to gneiss, and thus make it competent to carry channels to depth with or without addition of intrusives. The essence of a mining district is the presence of such competent rocks with long-lived, deep, penetrating breaks reopened to permit passage of heat and associated products from depths to surface. It is suggested that melts such as magmas; metamorphism up to and including granitization; alteration, such as orthoclase-quartz or quartz-sericite or garnet, and also mineralization, may all be by-products of such heat escape along channels made by tectonic forces at specific foci. Magnitudes of Districts (Fig. 1) Any synthesis of ore deposits must deal with comparable units. Ore deposits are innumerable, but great ore deposits, commercially important for a generation or more, are few. The bulk of metals has come from districts of the first and second magnitudes (over $1,000,000,000 and over $250,000,000, respectively), and of these the United States and adjacent provinces of Canada and Mexico contain only 28, of which 9 are first magnitude: Butte, Coeur d&apos;Alene, Bingham, Bisbee, Sierra Gold, in the West; Tri-State, Southeast Missouri, Michigan copper, Sud-bury, in the East. Another 28 or 30 districts are of third magnitude (over $50,000,000).

Jan 1, 1941

By William E. Ford, Edward Salisbury Dana

Examination in the Wet Way Examination by Means of the Blowpipe 479. The complete investigation of the chemical composition of a .mineral includes, first, the identification of the elements present by qualitative analysis, and, second, the determination of the relative amounts of each by quantitative analysis, from which last the formula can be calculated. Both processes carried out in full call for the equipment of a chemical laboratory. An approximate qualitative analysis, however, can, in many cases, be made quickly and simply with .few conveniences. The methods employed involve either (a) the use of acids or other reagents " in the wet way," or (b) the use

Jan 1, 1922

By Giovanni Barla, Stefan H. Boshkov

This paper examines the application of gelatin mixture models to the study of factors such as gravity effects, tectonic and residual stresses, anisotropy, physical nonlinearity, time-dependent behavior of the rock mass and connectedness of the geologic space. The technique of calibrating gelatin mixtures proposed by Richards and Mark in 1966 is applied to the particular problem considered. Similitude relationships between model and prototype are discussed with reference to the constitutive equations describing the physical behavior of the rock mass. The interaction between two openings in a linearly elastic medium, under conditions of plane strain, is used as an illustrative example with the view to describing the history of stress and deformation changes on the rock medium and lining around a slusher drift while undercuts are made in block caving. The prediction of the displacement, stress field and mode of fracture associated with a given rock structure, its initial stress field, and its physical properties is essential to rock mechanics and ground control. The basic approach is to assume the rock mass to behave as a continuous, homogeneous, and isotropic medium. The classical theory of elasticity is the simplest theory based on such a concept. Specification of the elastic constants, the initial state of stress in the ground, and the boundary conditions on stress and displacement allows one to predict stress and displacement within the body. Subsequently, provided that a criterion which governs rock fracture under various stress conditions has been established, a stability analysis of the rock structure can be performed. A natural extension of the present knowledge consists of removing some of the simplifying assumptions which characterize the analytical solutions based on the classical theory of elasticity. Complex geometry, the significance of tectonic and residual stresses, anisotropy, physical nonlinearity, time-dependent behavior of the rock mass and connectedness of the geologic space are some of the important factors which are neglected in the classical approach. A better insight into the real problem can be attained with either the finite element method of stress analysis or an experimental technique. The former has already been applied with success on several occasion 1-4 and is destined to render great service in the field of rock mechanics and ground control. The latter, which will be considered in this paper, has been used extensively in applications too numerous to be enumerated. Experimental technique involves either prototype testing, if the area to be studied is accessible, or model testing. Two- and three-dimensional photo-elastic analyses are very convenient means of obtaining the stress distribution in models of complex geometry. In general, such analyses are confined to studies of stress fields around openings which are sufficiently far removed from the surface boundary so that the stresses in their neighborhood are practically equal to those produced by an initial uniform stress field; i.e., so that gravitational effects are negligible. There are, however, many rock structures where these effects must be taken into account to attain a more realistic representation of the problem. Surface and near surface rock structures, systems of openings interacting with one another, and structural components loaded only by their own weight are some of the obvious examples. This paper was written to show how factors neglected in the usual analysis based on the classical theory of elasticity, can be taken into account when gelatin mixture models are used inconjunction with photoelastic methods. The interaction between two openings in a linearly elastic medium, under conditions of plane strain, is used as an illustrative example, with a view to describing the history of stress and deformation changes on the rock medium and lining around a slusher drift while undercuts are made in block caving. The birefringence of gelatin mixtures has been known for some time. A series of experiments were carried out by Rossi in 1910,5 but after that very

Jan 1, 1970

By J. C. Williams, M. J. Blackburn

Several of the decomposition processes that can occur in supersaturated phases in a Ti:11.6 wt pct Mo and a Ti:20 wt pct V alloy have been studied by transmission electron microscopy. The deformation induced "marternsitic phase" in the Ti:Mo alloy has been found to have a bcc or bct structure rather than the previously reported hexagonal structure. The morphology of&apos; the transformed region is a rather complex asserrlblage of twins, twinning occurring in one or more systems; this internal twinning has been found to occur on (112). The w phase is formed in both alloys on aging and is present in the Ti:Mo alloy after quenching. The structure of this phase has been confirmed as hexagonal in both systems, however, differences in morphology and stability are found between the two alloys. Thus in the Ti-Mo alloy the w phase has an ellipsoidal morphology with the major axis lying parallel to <111>ß or [0001]w while in the Ti-V alloy the phase forms as cubes, the cube faces lying parallel to {100}ß or {2021}w Some observations on the particle sizes, volume fraction, and composition of the w phase in the Ti-Mo alloy are listed. The mode of formation of The a phase from the (ß + w) structures is also different in the two alloys. In the Ti-Mo alloy the a phase is formed by either a cellular reaction or by the growth of isolated needles, whereas in the Ti-V alloy the a phase is nucleated at an w:ß interface and grow to consume the w phase. Some of the difjerences in behavior of the w phase are attributed to the mismatch between it and the solute enriched ß matrix in which it forms. MaNY transition elements tend to stabilize the bcc or ß-phase when added to titanium. In general two types of phase diagrams are produced, either a ß-stabilized (ß-isomorphous) system, e.g., Ti:Mo, -Ti:V, Ti:Nb, or a ß-eutectoid system, e.g., Ti:Cr, Ti:Fe, Ti:Mn. In previous papers&apos;-4 the phase transformations in the a-phase and (a + ß)-phase alloys have been described and this work has been extended to ß-stabilized systems. Specifically, transformations in the alloys Ti:20 wt pct V and Ti:11.6 wt pct Mo have been studied; in both of these alloys the ß phase is retained at room temperature when quenched from the ß-phase field. A number of phase transformations can occur in such metastable ß phases and the two alloys were chosen to include most of the transformations reported for ß-stabilized systems. We list these possible phase transformations below. Ti:11.6 Mo quenched from >780°C to retain the ß phase: a) The w phase can form on quenching.5 b) Martensite can be produced by subzero cooling or deformation. Two martensite habit planes have been reported in Ti:Mo alloys; (334)ß and (344)ß=6 c) On aging at temperatures <-550° C the w phase is formed before the a-phase.5,7 d) On aging at temperatures >550°C the a phase is formed.7 e) The martensite can be tempered. It has been reported that the a phase rather than the ß phase is precipitated during tempering.&apos; Ti:20V quenched from >660°C to retain the ß phase:9 a) At aging temperatures <260°C separation into two bcc phases occurs. b) The w-phase is produced prior to the a phase on aging at temperatures <-400°C. c) At temperatures 2400°C the a phase is formed directly. T-T-T diagrams describing the temperature and time regimes for the formation of these phases have been published7,9 for a Ti:12 pct Mo and a Ti:20 pct V alloy. We have attempted to investigate these transformations using transmission electron microscopy, however thin foils undergo a spontaneous transformation in all conditions except the equilibrium (a + ß) structure. This transformation has been reported previ0usly10,11 and we will comment on its morphology and nature in the various sections of experimental results. EXPERIMENTAL The compositions in wt pct of the two alloys investigated were: Ti:11.6 Mo, 0.100 02, 0.006 N2, 0.0015 H2 Ti:20V, 0.0574 O2, 0.0111 N2, 0.005 H2 These alloys were cold-rolled to 0.020 in. thick sheet. Specimens were heat treated in vacuum or in inert gas at temperatures >500°C and in a circulating air furnace at temperatures <500°C. Thin foils were prepared using standard techniques, described in detail previously." Dark field micrographs were obtained using high resolution technique. RESULTS Martensitic Transformation in Ti:11.6 pct Mo. Detailed study of the deformation induced martensite is not possible due to a spontaneous transformation which occurs near the edge of thin foils as shown in Fig. 1. Similar transformations have been observed in iron-" and copper-base13 alloys as well as other titanium alloys, but some observations specific to the Ti:1l.6 Mo alloy are listed below. a) The boundaries of these transformed regions are glissile and move under the influence of the electron beam during examination. b) Selected area diffraction indicates the transformed regions have the same structure as the matrix, being separated by tilt boundaries. The misori-

Jan 1, 1969