Search Documents

By Kenneth C. Vincent, A. M. Gaudin

IN a study1of the action of amyl xanthate on chalcocite in water suspension, it was found that if the xanthate is added in relatively large quantity the xanthate group can be accounted for in three forms: (1) as xanthate ion remaining in water, (2) as benzene-soluble cuprous xanthate on the chalcocite, (3) as a benzene-insoluble coating on the chalcocite. Reduction in the amount of xanthate added leads to disappearance of form 1 then of form 2. With minute quantities of added xanthate, substantially all the reagent is of the "unleachable" kind. Yet this unleachable xanthate can be dissolved by pyridine to form a soluble cuprous xanthate complex, and it is sufficient in effectiveness to make chalcocite flotable even if insufficient in quantity to form a complete monomolecular film on the mineral. In that study it was also found that chalcocite abstracts cuprous xanthate from benzene solution, in what may (or may not) be a case of molecular adsorption. It seemed desirable, therefore, to study further the "unleachable" xanthate on the chalcocite, and particularly to ascertain whether it is formed as a result of the benzene leach or is actually formed during the conditioning of chalcocite in aqueous xanthate solution. A splendid tool to make such studies has recently been perfected; that is, the use of radioactive spies or tracer atoms. With this tool, it was thought possible to answer the problem stated above, but, unfortunately, this did not prove to be true. Answer to the flotation question was clouded by the existence of rapid and selective diffusion of copper atoms in the solid mineral-a phenomenon that was totally unexpected yet remains interesting and perhaps important. METHOD OF RADIOACTIVE SPIES The method of radioactive spies is discussed in many places. Two convenient references are the article by Evans2 and the book by Pollard and Davidson.3 The method was first developed by Von Hevesy and Paneth in 1913, when only natural radioactive isotopes were available. These isotopes are few in number, and so the method remained limited in scope. Recently the synthesis of over 350 active isotopes of all the known stable chemical elements4 has opened widely expanded possibilities for the method. A fundamental tenet of the method is that a radioactive atom and a nonradioactive atom are exactly alike until disintegration of the radioactive atom. Then, by its sudden death, the spy reveals its location. The relative abundance of spies at various locations makes it possible to ascertain the relative abundance of the corresponding nonradioactive atoms at the same times and locations. A second fundamental tenet of the method of radioactive tracers is that the radioactivity lies in the nucleus of the atom: transfer of radioactivity from one

Jan 1, 1944

By Roy Lindgren

SINCE the year 1643, when the first blast furnace in America for treating iron ore was built at Saugus, Mass., out of mica schist quarried in the neighboring district, the procurement of a suitable refractory for furnace lining has been a problem of concern to the operators of furnaces. The stacks built of mica schist continued to smelt iron ore until about 1836, when, according to F. H. Norton, the first firebrick were produced1, at Queens Run, Pa. Other writers speak of brick having been molded and burned in Massachusetts about the year 1834. In 1841, Andrew Russell began to produce medium refractory plastic clay brick near East Liverpool, Ohio, that were used for lining blast furnaces1. The well-known Kentucky clay-producing district was not opened up until the year 1871, but since then it has produced a large percentage of the linings for iron blast furnaces. While some strides have been made by the refractories industry during the 100 years that have passed since the first firebrick were produced, it has been only during the last two decades that any real progress has been made towards bettering the product, even though the method of production had improved. Perhaps the fault lies with the user of the brick rather than with the producer, for not sooner demanding a supe-rior product. During the past 15 years the tonnage produced per lining has increased from 500,000 gross tons to 1,000,000 gross tons, and now some furnaces are producing 1,600,000 gross tons and better on a single lining. It is true that enlarged capacity of furnaces and improved practice have accounted for some of this increase in tonnage, nevertheless better quality in firebrick must be given credit for its share. However, we are not yet ready to say that we have reached a maximum life of furnace lining. We believe that a better product can be produced and that the refractories industries of America will, through their extensive research depart-

Jan 1, 1937

By H. C. Stumpf, L. A. Willey, V. L. Fink

Very few studies of the aluminum-sodium system have been reported. Heycock and Neville1 were unable to detect any solubility of sodium in liquid aluminum. Mathewson2 prepared an equilibrium diagram consisting of two horizontal lines at the melting points of the two metals. He was unable to detect solubility at either end of the system. Scheuer3 first developed a method for the chemical determination of sodium in aluminum and then studied the solubility of sodium in liquid aluminum. His method involved heating aluminum with excess sodium under hydrogen until the two liquids were at equilibrium, chilling the melt, and analyzing the aluminum-rich layer. He reported the solubility to be 0.10 pct sodium at 700°C, 0.115 pct at 750°C, and 0.128 pct at 800°C. This paper on the aluminum-sodium system is the twenty-first in a series from the Aluminum Research Laboratories describing equilibrium relations in aluminum alloy systems. Materials The alloys for this investigation were prepared from electrolytically refined aluminum (99.99 pct) and sodium of reagent quality conforming to specifications of the American Chemical Society. Chemical analysis of the aluminum showed the fol- lowing impurities: 0.002 pct Si, 0.002 pct Fe, 0.002 pct Cu, <0.001 pct Mn, 0.002 pct Mg and 0.001 pct Na. The sodium content of all alloys was determined by either chemical or spectro-graphic standard procedures5 No. IIA and No. SI I respectively. Determination of Miscibilitv The boundary of the miscibility gap was determined by a modification of the method of Scheuer3 and of that used by Henry and Cordiano. As finally developed the method was as follows: A fused alumina crucible 25 mm id with 75 mm depth and 1.5 mm wall thickness was placed on the bottom of a container made from a 4-in. length of 1 1/2-in. iron pipe and pipe caps. ?&apos;he space around the sides of the crucible was filled with 40 mesh crystalline alun-dum. A charge of 60 g of aluminum and 10 to 15 g of sodium was placed in the crucible, the sodium first being trimmed and rinsed with iso-pentane to remove kerosene. The container was tightly capped, filled with argon (99.6 pct pure), and heated to the desired temperature (between 670 and 800°C). A positive pressure of argon (about 8 mm of mercury) was maintained through a small pipe to the upper cap. After soaking for from 2 to 5 hr, the container was quenched by directing a stream of water onto the base, so that solidification of the aluminum-rich layer was rapid and essentially unidirectional. Analyses were made on drillings taken from the bottom of the ingots after machining off the surface layers. Pre-

Jan 1, 1949

By C. Gatlin, M. E. Chenevert

The effects of bedding plane orientation on the elastic constants and the yield strengths of three laminated rocks (one sandstone and two shales) and one isotropic rock (a limestone) were studied. The directional dependence of the elastic properties of these rocks was experimentally evaluated using a triaxial compression cell and auxiliary stress-strain measuring equipment. Symmetry of Poisson&apos;s ratios within the bedding plane suggested that horizontal isotropy exists, but the bedding planes do give rise to an appreciable difference between properties in the horizontal and vertical directions. For the three bedded rocks studied, Young&apos;s modulus was lower normal to bedding than along bedding. Yield strengths were determined at confining pressures from 0 to 12,000 psi in a triaxial compression cell. The rocks studied showed strength reductions as high as 40 per cent when the test specimen was oriented at 20°-30° to the bedding planes. The mechanical behavior of these rocks suggested that the rock properties of shear strength and/or coefficient of internal friction can vary with direction, depending on the particular rock tested. Tensile strengths were also measured and found to be lowest when failure occurred along bedding. This work shows that bedded formations exhibit sizable directional variations in both their elastic constants and yield strengths. It is suggested that these variations may be accounted for by using the "elastic laminate" model and the "variable coefficients" failure model. INTRODUCTION The nature of rock deformation at elevated pressures has been studied by many workers; papers by Handin,l,2 and Robinson3 illustrate the present state of knowledge. Most investigators have either chosen rocks which were as isotropic as possible (in order to avoid complications of data interpretation and analysis) or they have oriented their samples so that the effects of anisotropies (such as bedding planes) have been avoided. Of the studies performed, few were concerned specifically with mechanical anisotrop-ies. Griggs4 has presented limited data for specimens cut parallel, normal, and 45° to the bedding plane; he relates the strength anisotropy observed to the fabric (bedding) anisotropy. His tests were primarily concerned with large deformations (20 per cent strain); thus, no directional values of the elastic constants were reported. Handin has reported the results of similar experiments. Bott5has discussed rock strength anisotropies due to faults, cleavage, or bedding. He was concerned primari ly with determining the shear stress on such planes and did not mention the effect of friction. Jaeger6 later generalized Bott&apos;s work by taking friction into account and presented a limited theory for the failure of rocks having a "single plane of weakness", and also for rocks having a constant coefficient of friction, and a shear strength which varies with bedding plane orientation. Donath and Cohen,7 and Donathg have evaluated rock strengths from shale and slate specimens cut normal and parallel to bedding. A dependence of cohesive strength (7,) on the specimen orientation was also shown. Adler9 has also studied this problem and lists similar results. He assumes that all bedded rocks behave according to Jaeger&apos;s single-plane-of-weakness theory. Kalinin and Belorussov10 list results for strength tests parallel and perpendicular to bedding and use this information as a basis for hole deviation analysis. From the literature it is apparent that sedimentary rocks have been tested under widely varying conditions of stress; however, the assumption of isotropy is generally, but not always, made. Since geologic sedimentation often deposits sediments in very definite lavers.,. it seems that more svstema tic attention should be given to the possible effects of this natural bedding. Bedding, as used here, refers to visible regularities of grain size or orientation resulting from depositional processes. The mechanical strength anisotropies, which bedding may present, is not the only anisotronic property to be considered, since the elastic

Jan 1, 1966

By C. W. Macgregor

The observation of the flow layers, or Luders&apos; lines, produced in mild steel when it is stressed into the plastic range often provides considerable useful information for the study of the fundamental mechanism of the plastic flow of metals. It is a commonly observed fact that as soon as the upper yield point in a mild-st&apos;eel tensile-test bar is passed, an unstable condition develops in the equilibrium, the load on the testing machine drops and if the surface of the bar contains a thin mill scale, the latter begins to flake off rapidly along certain "lines." These "lines" are ill reality traces of wedge-shaped flow layers and are formed by the inter-section of the surface of slip and the surface of the bar. The average plane of the flow layer itself has been found by various experimenters to be inclined at an angle of approximately 45" to the axis of the test bar. In a body of more complicated shape stressed in possibly a different man-ncr, the tangent planes to the flow layers at each point seem in many cases to be inclined at an angle of about 45" to the principal stress direct-tions at the point. As examples of the latter may be mentionecl the logarithmic spirals obtained when a rivet hole is punched in a thin plate, or when a tube is subject,ed to internal pressure only, etc. IIencc if the flow layers are observed from an experiment, the shear-st&apos;ress trajectories —the curves indicating the direct,ions of the maximum shearing stresses in the body—may then be approximately determined. Since the latter curves form an orthogonal family inclined at 45" to the principal stress directions, the family of principal stress trajectories, or the curves irldicating the directions of the principal stresses, may be thus obtained Although the discontinuous type of stress-strain curve at the yield point is commonly observed with test bars of mild steel, more recent experiments have shown that this is by no means the only material exhibiting this interesting phenomenon. A similar effect has been observed in zinc and cadmium crystals, by Becker and Orowai~; in duralumin and other aluminum alloys, by Dawidenkow,~Elam,~ Fell4 an(l others; in copper and copper-alloy crystals, by Elam;~ in brass by Elam;3 in brass wires by deForest;" in higher carbon steels, tungsten steel, and

Jan 1, 1939

By C. W. MacGregor

The observation of the flow layers, or Luders&apos; lines, produced in mild steel when it is stressed into the plastic range often provides considerable useful information for the study of the fundamental mechanism of the plastic flow of metals. It is a commonly observed fact that as soon as the upper yield point in a mild-st&apos;eel tensile-test bar is passed, an unstable condition develops in the equilibrium, the load on the testing machine drops and if the surface of the bar contains a thin mill scale, the latter begins to flake off rapidly along certain "lines." These "lines" are ill reality traces of wedge-shaped flow layers and are formed by the inter-section of the surface of slip and the surface of the bar. The average plane of the flow layer itself has been found by various experimenters to be inclined at an angle of approximately 45" to the axis of the test bar. In a body of more complicated shape stressed in possibly a different man-ncr, the tangent planes to the flow layers at each point seem in many cases to be inclined at an angle of about 45" to the principal stress direct-tions at the point. As examples of the latter may be mentionecl the logarithmic spirals obtained when a rivet hole is punched in a thin plate, or when a tube is subject,ed to internal pressure only, etc. IIencc if the flow layers are observed from an experiment, the shear-st&apos;ress trajectories —the curves indicating the direct,ions of the maximum shearing stresses in the body—may then be approximately determined. Since the latter curves form an orthogonal family inclined at 45" to the principal stress directions, the family of principal stress trajectories, or the curves irldicating the directions of the principal stresses, may be thus obtained Although the discontinuous type of stress-strain curve at the yield point is commonly observed with test bars of mild steel, more recent experiments have shown that this is by no means the only material exhibiting this interesting phenomenon. A similar effect has been observed in zinc and cadmium crystals, by Becker and Orowai~; in duralumin and other aluminum alloys, by Dawidenkow,~Elam,~ Fell4 an(l others; in copper and copper-alloy crystals, by Elam;~ in brass by Elam;3 in brass wires by deForest;" in higher carbon steels, tungsten steel, and

Jan 1, 1939

By G. D. Monk, W. C. Krumbein

The relation between permeability and the size parameters of unconsolidated sand is approached by considering sands as logarithmic frequency distributions having the basic parameters mean size and standard deviation. Sieve separates were mixed in accordance with the normal logarithmic probability law, so that the mean and standard deviation could be varied at will. Experiments were conducted in which one parameter was kept fixed and the other varied; in this manner the dependence of permeability on the individual parameters was evaluated. It was found that permeability can he expressed as the product of a power function of the mean size and an exponential function of the standard deviation. Earlier studies of the effect of size of particles on the permeability of uncon-solidated sand have shown that the permeability varies with the square of some average diameter. This was first pointed out by Hazenl in 1892 and verified by Slichter2 in 1898. Hazen&apos;s mean size was defined as the 10 percentile of the cumulative curve (i.e., size that is smaller than 90 pel cent of the distribution and larger than 10 per cent). Slichter&apos;s effective size, on the other hand, was found by Wilsey3,4 to agree with the 31 percentile. Fair and Hatch6 found that the geometric mean size of sieve separates yielded the same power function; Hulbert and Feben6 found that the permeability of sieve separates varied as the 1.89 power of the median diameter (i.e., the size associated with the 50 percentile of the cumulative curve). Relatively few studies included the effect of the "sorting" of the sediment on the permeability. It was recognized that the nature of the size distribution, in terms of the spread of the particles about the mean, affects the permeability, but no systematic investigations of this effect are known to the writers. Cloud7 demonstrated that the effect of the grain-size distribution on permeability is definitely measurable. In the present paper the authors investigate this relation analytically, and show that the effects of the size parameters on permeability may be predicted for at least a restricted set of conditions. Properties OF Sediments Recent investigations have shown that essentially all the geologically important characteristics of sediments may be expressed in terms of six measurable quanti-tities possessed by each clastic sedimentary particle. These attributes are: (I) size, (2) shape (sphericity), (3) roundness (angularity) , (4) mineralogical composition (density), (5) surface texture, (6) orientation. Each of these characteristics may be defined in several manners. Size may be expressed in terms of sieve mesh, settling velocity, volume, etc. Sphericity is a shape concept introduced by Wadell;8 it is essentially a measure of the ratio of the surface area of an equivalent sphere to the surface area of the particle. The same

Jan 1, 1943

By G. D. Monk, W. C. Krumbein

The relation between permeability and the size parameters of unconsolidated sand is approached by considering sands as logarithmic frequency distributions having the basic parameters mean size and standard deviation. Sieve separates were mixed in accordance with the normal logarithmic probability law, so that the mean and standard deviation could be varied at will. Experiments were conducted in which one parameter was kept fixed and the other varied; in this manner the dependence of permeability on the individual parameters was evaluated. It was found that permeability can he expressed as the product of a power function of the mean size and an exponential function of the standard deviation. Earlier studies of the effect of size of particles on the permeability of uncon-solidated sand have shown that the permeability varies with the square of some average diameter. This was first pointed out by Hazenl in 1892 and verified by Slichter2 in 1898. Hazen&apos;s mean size was defined as the 10 percentile of the cumulative curve (i.e., size that is smaller than 90 pel cent of the distribution and larger than 10 per cent). Slichter&apos;s effective size, on the other hand, was found by Wilsey3,4 to agree with the 31 percentile. Fair and Hatch6 found that the geometric mean size of sieve separates yielded the same power function; Hulbert and Feben6 found that the permeability of sieve separates varied as the 1.89 power of the median diameter (i.e., the size associated with the 50 percentile of the cumulative curve). Relatively few studies included the effect of the "sorting" of the sediment on the permeability. It was recognized that the nature of the size distribution, in terms of the spread of the particles about the mean, affects the permeability, but no systematic investigations of this effect are known to the writers. Cloud7 demonstrated that the effect of the grain-size distribution on permeability is definitely measurable. In the present paper the authors investigate this relation analytically, and show that the effects of the size parameters on permeability may be predicted for at least a restricted set of conditions. Properties OF Sediments Recent investigations have shown that essentially all the geologically important characteristics of sediments may be expressed in terms of six measurable quanti-tities possessed by each clastic sedimentary particle. These attributes are: (I) size, (2) shape (sphericity), (3) roundness (angularity) , (4) mineralogical composition (density), (5) surface texture, (6) orientation. Each of these characteristics may be defined in several manners. Size may be expressed in terms of sieve mesh, settling velocity, volume, etc. Sphericity is a shape concept introduced by Wadell;8 it is essentially a measure of the ratio of the surface area of an equivalent sphere to the surface area of the particle. The same

Jan 1, 1943

By P. D. Hunt, I. Johnson, M. G. Chasanov, H. M. Feder

The solubilities of the transition metals from scundium to nickel, inclusive, in liquid cadmium were determined by sampling saturated solutions. At 400°C these solubilities (ppm) are:Sc, Co, 22; Ni, 12000. Relative partial molal enthalpies and excess partial molal entropies at infinite dilution for the solutes Cr, Mn, Fe, and Co are compared zoitlz similar data for the post-transition metals. Three new intermetallic phases, ScCd,, TiCd, and Ti,Cd, encozaztered in the course of this work, are reported. Measurements of the solubility of the 3-d transition metals in liquid cadmium have been reported&apos; only for iron. The present measurements for the entire series were made as an aid to the study of the systematics of alloy formation. EXPERIMENTAL The apparatus and sampling techniques used for the solubility determinations were similar to those described by Martin etal.&apos; Temperatures were measured with a Pt/Pt-10 pct Rh thermocouple sheathed in recrystallized alumina and immersed in the solution. The thermocouple was recalibrated periodically during the course of the investigation. Thermocouple voltages were measured to the neares 0.01 mv with a Rubicon model 2732 potentiometer. A scaled-down version of the apparratus, in which the total metal charge was about 90 g, was employed to measure the solubility of scandium. Two-mm ID Vycor filter pipets were used to sample the scandium-cadmiurn solutions; the samples weighed about 2g- Cadmium with a minimum purity of 99.95 pct was used; the only impurities detected spectrochem-ically were C&apos;u and Mg, both less than 10 ppm. The purities of the other metals were: scandium, 99.9 pct; titanium. 99.92 pct; vanadium, 99.9 pct; chromium, 99).99 pct; manganese, 99.9+ pct; iron, 99.90 pct; cobalt, 99.95 pct; and nickel, 99.96 pct. Solidified melts were routinely analyzed spectro-graphically. No significant contamination by the crucible, sampling pipets, or other materials of construction was observed. The entire specimen obtained by sampling was dissolved to preclude analytical errors due to segregation on cooling. Colorimetric methods3 were used for the analyses of cobalt (2-nitroso-l-naphthol), manganese (permanganate), nickel (dimethylglyoxime), titanium (peroxide), and vanadium (thiocyanate).4 Chromium, iron, and scandium were neutron-irradiated to produce The dissolved samples were gamma-counted to determine solute concentration.For the separation of intermediate phases from cadmium-rich alloys selective leaching by saturated ammonium nitrate solutions was employed. The concentration of cadmium in the successive leaches was followed polarographically and the process was terminated when the rate of cadmium dissolution decreased markedly. For the further investigation of intermediate phases 1/4- in. diam powder compacts were pressed at 80,000 psi and annealed in argon at 315" to 330°C for 10 days. Larger quantities of alloys were prepared in sealed tantalum capsules heated in a rocking furnace.

Jan 1, 1962

By N. A. Ziegler

IN every research it is desirable to eliminate as many variables as possible and to leave only a few to be investigated one at a time. Metallurgical problems are no exception. Some of the variables that are difficult to control are the size, the distribution, and the orientation of the grains in a metallic test piece. It is therefore very desirable to obtain isolated metallic grains (single crystals, as they are commonly called) large enough to enable one to study their mechanical and physical properties. The present investigation is a part of magnetic research work on iron and iron alloys, undertaken to obtain, if possible, the magnetic properties of pure iron (Fe). This paper will deal primarily with the preparation of single crystals of iron and their mechanical properties, while another paper, by T. D. Yensen, now in preparation, will deal specifically with their magnetic properties. The work with "single crystals" is attracting more attention every year among the investigators in metallurgy. Van Liempt1 gives an interesting summary of the work done and the different methods used in the preparation of metallic single crystals. Briefly stated, the four principal methods used are the following: 1. The cooling of a liquid metal in such a way that the crystallization would start at one point only, causing the entire liquid to solidify as one crystalline unit. This method can be successfully applied to the majority of the metals that do not have any allotropic transformations in the solid state. It has been used and described by a number of investigators,2 but it has never been successfully applied to iron on account of allotropic transformations.

Jan 1, 1930

By R. W. Gurry

IN the course of a series of measurements of the rate of diffusion of carbon in austenite at about 960°C. (1760°F.) and 1110°C. (2030°F.), it became necessary to determine carbon concentration when austenite is saturated with graphite, because of indications that the hitherto accepted value of the solubility of graphite in this temperature range is too low. Specimens of carbonyl iron were saturated at temperature in a hydrogen-toluene atmosphere which was in equilibrium with graphite. The carbon content of the steel was measured either by combustion or by the loss of weight after substantially complete decarburization in an atmosphere of hydrogen saturated at room temperature with water vapor. The absence of carbide or graphite as a phase at temperature was demonstrated by microscopic examination of saturated specimens that had been drastically quenched. The mean result of concordant measurements is that gamma iron saturated with respect to graphite contains 1.39 per cent carbon at 957°C. (1755°F.) and 1.89 per cent at 1110°C. (2030°°F.). These two values, plotted along with what appears from the literature to be the best value (0.69 per cent) at the iron-graphite eutectoid temperature (738°C. or 1360°F.), yield a curve that is almost linear, and which, continued upward through a short interval, leads to a limiting solubility of 1.98 per cent at the iron-graphite eutectic temperature1135°C. (2095°F.) instead of the commonly accepted value of about 1.7 per cent. EXPERIMENTAL PROCEDURE The samples of carbonyl iron, with the exception of those for microscopic examination, were cylinders 3.8 cm. long, 0.475 cm. in diameter. They were placed in a graphite holder and suspended in a vertical furnace, the temperature of which was controlled precisely by means of the resistance of the platinum winding.1 In the empty furnace the range of temperature over a distance of 4 cm, at the heat center was 9°C. (16°F.) but at a given location the temperature remained within ±0.5°C. (0.9°F.); it was measured by inserting a platinum-rhodium couple calibrated at the melting point of palladium, 1555°C. Since the presence of the sample probably improved the uniformity of temperature, it was decided to consider the average temperature of the sample to be 3°C. lower than the maximum measured in the empty furnace with the same setting of the controller. Data were obtained in the vicinity of two temperatures, 960°C. (1760°F.) and 1110°C. (2030°F.). The samples for microscopic examination, 2.2 cm. long, 0.475 cm. in diameter, were suspended individually on pure iron wire; for these no temperature correction was applied. The carburizing gas passed into the furnace was dry, oxygen-free hydrogen saturated at room temperature with

Jan 1, 1942

By Herbert Haas

1. INTRODUCTION COPPER matte is now converted into blister copper at a cost of only $5 per ton of copper, or, based on a 40 per cent. matte, $2 per ton of matte, which is the record of at least one large smelting Works; and it seems hardly likely that a further reduction, large enough to warrant, a change in existing practice, could be made in bessemerizing costs. But the new type of converter here described and the new practice proposed are intended, not so much for the treatment of mattes, as for the extension of, the process to the direct reduction in the copper-converter of pyrite ores

Jan 6, 1914

[NORTH AMERICA UNITED STATES Alabama BIRMINGHAM BURROWS, WILLIAM C. CORD, RICHARD H. COSTON, OTIS D. JR. FAIRHOPE RUFFLES, WILLIAM R. HUNTSVILLE WAGGONER, JERRY B. MOBILE PETROUTSON, PETER C. SELMA JONES, JAMES J. JR. UNIVERSITY CUDWORTH, JAMES R. JONES, WALTER B. RICHARDS, EDWARD F.]

Jan 1, 1961

By S. Floreen

Seven iron alloys ranging from 5 to 12 pct Ni and 5 to 14 pct Cr were studied. All alloys transformed to bcc massive martensites. Tempering increased the strengths , probably because of relief of residual stresses generated by the martensite transformation. The major strengthening mechanism appeared to be solid-solution hardening by nickel and chromium. Studies of the work-hardening behaviw, of the effects of prior austenite grain size, and of the effects of changing strain rate and test temperature gaue results very similar to iron or low-alloy steels. Increasing nickel contents markedly improved the toughness at subzero temperatures. Studies of the flow properties did not, however, indicate the reason for the beneficial effect of nickel on toughness. The marine atmosphere corrosion resistance of the alloys was improved primarily by chromium additions, but increasing nickel contents were also beneficial at low levels of chromium. J\ number of maraging and PH stainless steels are strengthened by precipitation hardening in a low-carbon Fe-Ni-Cr martensite matrix. To some extent the resultant properties of these steels must depend upon the properties of this matrix. The present study therefore was conducted to evaluate the transformation characteristics and mechanical properties of a series of Fe-Ni-Cr martensitic ternary alloys. A limited evaluation of the corrosion resistance of the alloys in marine atmosphere was also made. ALLOY PREPARATION Seven 100-lb air induction melts were prepared using electrolytic iron, nickel, and chromium metal additions. The initial Fe-Ni charge also contained 0.05 wt pct graphite to produce a carbon boil during melt down. After melting of the base charge, the heats were refined with 0.1 wt pct additions of manganese, silicon, aluminum and titanium and poured into cast-iron molds. The ingots were homogenized at 1250°C and uni-directionally hot-rolled to 2-in. plate. They were then homogenized another hour at 1250°C, and unidirection-ally hot-rolled to %-in. plate at a finishing temperature of approximately 1050°C. The compositions of the heats are given in Table I. Two additional heats were prepared as 40-lb vacuum-induction melts using electrolytic iron, nickel, and chromium metals, and commercially pure molybdenum chips. A carbon boil, and 0.1 wt pct additions of aluminum and titanium were again employed, but manganese and silicon were not added. The heats were converted to %-in. plate using the procedure described above. The compositions of these heats are included in Table I.

Jan 1, 1967

By Herbert J. French

Herbert 1. French (Member 1934), vice president of the International Nickel Co. Inc., assistant vice president of the International Nickel Co. of Canada Ltd., and AIME Howe Memorial Lecturer for 1956, died in Rochester, Minn. on Aug. 17, 1955, after a long illness. Before his death, Mr. French had laid the foundation of research on which the Howe Memorial Lecture (p. 770) was based. His associates at Inco, 0. 0. Miller and J. W. Sands, were able to complete the project, present the lecture, and prepare it for publication, following Mr. French&apos;s general outline. Born in New York on May 27, 1893, he graduated from the School of Mines, Columbia University, with a degree in metallurgical engineering in 1915. Mr. French gained his early engineering experience with the American Smelting and Refining Co., serving as a chemist and as-sayer at the company&apos;s Murray, Utah, installations. He later returned east and became a metallurgical engineer for the General Vehicle Co., Long Island City, IT. Y., a subsidiary of the General Electric Co. In 1917 Mr. French was appointed civilian inspector of materials for the U.S. Army Signal Corps, and continued this work when it was later absorbed into the Bureau of Aircraft Production. Subsequently he was appointed district inspector in Philadelphia for the Pittsburgh (Ordnance Metallurgical) office, later transferring to Pittsburgh. After World War I Mr. French became an assistant physicist on the metallurgical staff, U. S. Bureau of Standards, Washington, D. C. During his years with the Bureau, he was successively associate physicist, metallurgist, senior metallurgist, and assistant chief, division of metallurgy. In 1929 Mr. French joined International Nickel as a metallurgist at the company&apos;s Bay-onne, N. J., research laboratory. Transferring to the development and research division, New York, in 1931, he took charge of alloy steel and iron development, becoming assistant manager of this division in 1943. Mr. French&apos;s appointment as an Inco vice president came in March 1947. Previously, he was appointed assistant vice president of the International Nickel Co. of Canada Ltd. in January 1947. Mr. French served the War Production Board during World War II as senior technical consultant in charge of the metallurgical and specifications section of the iron and steel branch. When this section of the WPB was organized into the steel division, he was appointed chief of the metallurgical branch. From March 1944 to September 1945 Mr. French served as assistant director. Herbert French was well known not only for his prolific contribution to the metallurgical literature, for which he received numerous awards, but also for his prolonged service to the profession through its technical societies. He was a past president of ASM, and was the Campbell Memorial Lecturer for that group in 1933. Mr. French was honored by the American Society for Steel Treating in 1931 when he was awarded the Henry Marion Howe Medal. A series of lectures he gave in 1941 before the Fourth Western Metal Congress in Los Angeles was later published in book form under the title Alloy Constructional Steels.

Jan 1, 1957

By J. E. Johnson

Charcoal-iron is quantitively so unimportant compared with coke-iron, that its qualitative importance for many industrial purposes is entirely unkriown to many coke-furnace-men, and to the great majority of the inembers of this Institute. To explain this qualitative importance, and explain some of the fact,ors that affect the quality, are the objects of this paper. A brief review of&apos; the commercial conditions governing the charcoal-iron industry is a necessary preliminary to any adequate treatment of the subject. The advent of coke-iron, which transformed the whole iron industry commercially, left intact a limited production of charcoal-iron in the East and South, which has been conducted almays on the basis of high cost and high quality, with correspondingly high selling-price. In the Northwest, particularly in the Lake Superior district, the development has been along totally different lines, for which the close proximity of the great iron-ore deposits and the great forests of that region mere responsible. When the great white-pine forests were removed there were left behind large areas of hardwood and hemlock, to which little attention was paid in the prosperous years of the white-pine industry. But when the latter declined, the demand for lumber, and the presence of lumber-men, probably more skilled than any others in the world, caused the gradual introduction of these woods into commercial use. It was a matter of ancient knowledge that hardwood made an excellent charcoal, and to utilize the cordwood left after the saw-logs were removed, by converting it into charcoal and using it to smelt ore from the adjacent mines, mas an obvious step. In some cases the establishment of the furnace occurred in-

Jan 1, 1913

By W. F. Domis, F. von Gemmingen, R. W. Whitmore, F. Garofalo

Constant-load creep-rupture tests at 1100°, 1300° and 1500°F were made on a Type-316, 18 Cr-8 Ni-ZMo, austenitic stainless steel to determine the relationship between ruptzire life and other aspects of creep behavior, The test program was designed on a statistical basis to check the variability of various creep properties and to determine emprically the dependence of minimutn creep rate and ruptzire life on initial stress, The dependence of the rupture life, tn, on the initial stress, a,, is found to be related to the stress dependence of the wrinimum creep rate, i,, and secondary creep strain, The instabilities or breaks found in the conventionual log - logt, plots can be traced to either a change in the linear dependence of log i, on log a, or to a change in secondary creep strain. In the alloy tested, rupture is found to be predowmanantly of the inter crystalline type, For this material, the secondary creep strain is -found to depend on the nature of the grain boundary precipitate, which affects grain boundary migration. It has been shown for a variety of metals and al tested at elevated temperatures under creep conditions that the empirical relationship exists between rupture life, tr, and minimum creep rate, i,. This relationship, in which C and a are in some cases independent of stress or temperature, shows in a general way that creep rupture depends on creep behavior prior to tertiary creep stage. To determine more fully the factors which control creep rupture requires, therefore, more knowledge of the relationship between rupture and creep behavior. To obtain such information, constant-load creep-rupture tests have been made on a Type-316, 18 Cr-8 Ni-2 Mo, austenitic stainless steel at 11000, 1300°, and 1500°F. These tests were designed on a statistical basis to determine the variability of the various creep properties measured and to determine empirically the stress dependence of minimum creep rate and rupture life. As a result of this work, various empirical relations have been established defining more closely the factor, C, in the relation between rupture life and minimum creep rate. This factor is found to be proportional to the amount of strain during secondary creep. The variation of secondary creep strain with rupture life and temperature is determined and its effect on rupture behavior discussed. The variability in minimum creep rate and rupture life is also dis- cussed and the dependence of these quantities on initial stress is interpreted. TEST MATERIAL AND TEST PROCEDURES The material tested is an austenitic stainless steel, AISI Type 316, of the following composition: C, 0.07 pct; Mn, 1.94 pct; P, 0.01 pct; S, 0.021 pct; Si, 0.38 pct; Cr, 18 pct; Ni, 11.4 pct; Mo, 2.15 pct; All 0.003 pct and N, 0.043 pct. The material was received as a hot-rolled 0.5-in. diam bar which was sectioned into 3.25 in. long blanks. Each blank was heat treated by holding 1/2 hr at 2000° F followed by water quenching. A 3/8-in. coupon was removed from each heat-treated blank and the microstructure was examined, the grain size determined, and the hardness measured. The microstructure was found to be uniform from blank to blank and the grain size was found to range from 4 to 6 ASTM numbers. Hardness, measured using a 20-kg load, varied between 127 and 148 Vpn. Tensile creep-rupture specimens having a 0.25 in. diam within a 1.5-in. reduced section were machined from the heat-treated blanks. Constant-load tests were made on these specimens at 1100°, 1300°, and 1500 F. Six specimens were tested at each stress level. Three creep-rupture machines were employed for tests at each temperature, two specimens being tested in each machine for each stress level. To minimize any effect due to local inhomogeneities along the length of the as-received bar the specimens were randomized before test. Each specimen was tested to rupture and in most cases an autographic extension-time curve was obtained. For very low stress levels at 1500°F no auto-

Jan 1, 1962

By William F. Harris, Joseph Easha

FOR many years basic control of refinery operations depended on visual observation of small chill specimens poured at various intervals during processing. The oseto of these samples was related to the physical and chemical properties of the metal. Since the =setn is dependent on many factors other than oxygen content, this method, while giving a general indication of the condition of the copper, does not accurately measure the oxygen content. For the last 3 years a modified vacuum fusion procedure which enables the operator to determine the oxygen content of the copper within 1 5 min of sampling has been in use at the Westinghouse Copper Mill. For use with this apparatus a sampling technique has been developed which gives oxygen values representative of the oxygen content of the wire bar. The sampling technique is based on a statistical study, which compared the oxygen content of the laboratory sample of copper poured at the same time a wire bar was being poured, with the oxygen content of the wire bar. The apparatus used for the determination of oxygen in copper is shown in Fig. 1 and is essentially the same as previously described but with one important modification. A very porous fritted glass disc has been inserted in the tubing between the manom- eter and 40/50 ground glass joint. The fritted disc retains the copper vapor and copper particles in the furnace section and prevents contamination of the mercury in the manometer. Without the disc the manometer became difficult to read after a few weeks of operation. In earlier work1 it had been established that the simplified vacuum fusion apparatus used at the Copper Mill gave essentially the same results as a con-vential vacuum fusion apparatus. However, for this study it was necessary to determine the difference, if any, between the oxygen content of the wire bar and the oxygen content of the small chill sample used for the oxygen analysis. This correlation was established by taking a chill sample at the same time wire bars were being poured. The wire bar being poured at the time the chill sample was taken was marked and removed for further analysis. The copper is sampled at various times during refining and cast into laboratory size samples with the mold shown in Fig. 2. The mold is made of cold rolled steel and is 2 in. high and 2 1/2 in. in diam. The large upper portion of the cast sample is used for measurement of the conductivity of the copper, The lower portion which is a rod about 1/4 in. diam by 3/4 in. long is used for determination of the oxygen content. This portion of the sample weighs about 5 g which is approximately the size sample used for the analysis. The only preparation neces-

Jan 1, 1962

By Arthur F. Taggart, Nathaniel Arbiter

The fact that the floatability of minerals with fatty-acid collectors changes as the pH of a pulp varies was utilized in the early days of flotation, when sulphuric acid was used with oleic acid to float sphalerite and galena. from gangues which themselves float with fatty acids in alkaline pulps. Gaudin1 showed that this difference in floatability is a regular function of the extent of the change in pH. The present paper offers an explanation of the phenomenon, and on the basis thereof sets up recommendations for control of soap-flotation operations. Experimental Parallelism between floatability of a mineral in a given environment and its contact angle in that environment is so well established,2 and the contact angle is so readily and rapidly measurable, that contact angles have been used throughout the experimental work to indicate relative floatability. Experiments comprised contact-angle measurements on a number of representative minerals and metals, and a variety of subsidiary tests designed to check and to amplify the contact-angle indications. Contact-angle measurements were made by the method described in detail by del Giudice.3 Sequence of procedure for determination of the points of Fig. I was: I. Polish specimen. Most specimens yielded zero contact angle after polishing; a few showed a slight "cling." Cling is characteristic of specimens that pit on polishing; it is due to a residue of organic contamination, originally on the particle surface, which persists in the pits. The cling did not change total contact angle after conditioning, and is not, therefore, additive in the upper part of the curves of Fig. I. It may have broadened the bases of the curves for the affected minerals slightly. 2. The specimen was next conditioned in soap solution for 5 minutes. 3. The conditioned particle was transferred, under conditions that precluded surface drying, to an aqueous solution of the pH desired and contact angle determined. 4. The particle was thereupon transferred, again without surface drying, to water. The confirmatory tests will be described at the places pertinent in the argument. Discussion of Results Gaudin and Vincent4 have shown that contact angles with heptoic acid as a collector decrease for a given specimen when the concentration of collector present falls below a certain value. A similar reduction in angle occurs with collector-conditioned particles that are visibly slime-coated, and varies roughly with the extent of coating. Since in the last case the reduction in angle is certainly due to reduction in the proportion of total conditioned mineral surface presented to the bubble, the authors believe that the same condition prevails in the first case cited, and that similar reduction in angle and floatability will occur whenever starvation quantities of collector are present, whether by design or by reason of excessive consumption.

Jan 1, 1943

By Nathaniel Arbiter, Arthur F. Taggart

The fact that the floatability of minerals with fatty-acid collectors changes as the pH of a pulp varies was utilized in the early days of flotation, when sulphuric acid was used with oleic acid to float sphalerite and galena. from gangues which themselves float with fatty acids in alkaline pulps. Gaudin1 showed that this difference in floatability is a regular function of the extent of the change in pH. The present paper offers an explanation of the phenomenon, and on the basis thereof sets up recommendations for control of soap-flotation operations. Experimental Parallelism between floatability of a mineral in a given environment and its contact angle in that environment is so well established,2 and the contact angle is so readily and rapidly measurable, that contact angles have been used throughout the experimental work to indicate relative floatability. Experiments comprised contact-angle measurements on a number of representative minerals and metals, and a variety of subsidiary tests designed to check and to amplify the contact-angle indications. Contact-angle measurements were made by the method described in detail by del Giudice.3 Sequence of procedure for determination of the points of Fig. I was: I. Polish specimen. Most specimens yielded zero contact angle after polishing; a few showed a slight "cling." Cling is characteristic of specimens that pit on polishing; it is due to a residue of organic contamination, originally on the particle surface, which persists in the pits. The cling did not change total contact angle after conditioning, and is not, therefore, additive in the upper part of the curves of Fig. I. It may have broadened the bases of the curves for the affected minerals slightly. 2. The specimen was next conditioned in soap solution for 5 minutes. 3. The conditioned particle was transferred, under conditions that precluded surface drying, to an aqueous solution of the pH desired and contact angle determined. 4. The particle was thereupon transferred, again without surface drying, to water. The confirmatory tests will be described at the places pertinent in the argument. Discussion of Results Gaudin and Vincent4 have shown that contact angles with heptoic acid as a collector decrease for a given specimen when the concentration of collector present falls below a certain value. A similar reduction in angle occurs with collector-conditioned particles that are visibly slime-coated, and varies roughly with the extent of coating. Since in the last case the reduction in angle is certainly due to reduction in the proportion of total conditioned mineral surface presented to the bubble, the authors believe that the same condition prevails in the first case cited, and that similar reduction in angle and floatability will occur whenever starvation quantities of collector are present, whether by design or by reason of excessive consumption.

Jan 1, 1943