Search Documents

By Joseph W. Leonard, T. S. Spicer

INTRODUCTION Reasons for Thermal Drying The continuing increase in the percentage of minus %-inch coal produced as a result of the increased use of mechanical mining methods has, over the years, tended to shift considerable portions of the work of producing saleable coal to the fine coal cleaning section of the preparation plant. Because a given weight of fine coal will contain substantially greater surface area than an equivalent weight of coarse coal, it follows that, when subjected to wet cleaning processes, the fines will absorb and retain consider- ably more moisture than coarser fractions. Increased moisture pickup in the finer sizes complicates fine coal cleaning since beneficiation may not be limited to the removal of ash and sulfur but often must be expanded to include the additional step of thermal drying to remove excessive moisture. Thus, water which provides the medium for cleaning fine coal is in itself detrimental and, like ash and sulfur, reduces coal quality. Removal of surface moisture by drying is done for one or more of the following 1 reasons: (1) To avoid freezing difficulties and to facilitate handling during shipment, storage and transfer to the points of use; (2) to maintain high pulverizer capacity; (3) to reduce heat loss due to evaporation of surface moisture from the coal in the burning process, thus increasing heating efficiency; (4) to improve the quality of coal used for special purposes, such as in the production of coke, briquettes, and chemicals; (5) to decrease transportation costs; and (6) to facilitate dry coal-cleaning processes. Because benefits to coal transportation and utilization are the most common reasons for thermal drying, the following sections will examine these areas in greater detail. Benefits to Transportation Initial benefits from drying are the reduction of shipping costs from the mine to the point of utilization since more coal can be concentrated into a given weight of product when worthless moisture is removed. Non- combustible~ such as water and mineral matter in railroad shipments of coal are billed the same as coal at $3.32 per ton, according to the recent average costs. Savings of 10 to 20 dollars from drying on the shipment cost of each 50 to 60 tons of coal contained in a typical railroad car is common. Savings on coal shipments from individual mines which result from coal drying can be expressed in terms of hundreds of thousands of dollars and more each year. For example, a reduction of shipping charges of only 5 percent on one million tons per year would mean a savings of 166,000

Jan 1, 1968

By D. J. McAdam

IN a recent survey of the literature, the author has found evidence incompatible with prevalent views regarding the technical cohesive strength and yield strength of metals. Some of the evidence regarding the technical cohesive strength was presented in a previous paper,21 and views were presented that are believed to be in better accord with the evidence. In that paper, it was shown that the technical cohesion limit (contrary to prevalent views) varies with the combination of principal stresses,† and that the influence of plastic deformation on the technical cohesive strength is not in accordance with prevalent views. In this paper, consideration will be given to both the technical cohesion limit and the yield stress as affected by the combination of principal stresses. Evidence will be presented that the variations of the yield stress and the technical cohesion limit with the combination of principal stresses are not in accordance with prevalent views. Consideration will also be given to ductility and work-hardening capacity, which depend on the initial difference between the technical cohesion limit and the yield stress. By the "technical cohesion limit" is meant the mean stress at actual or potential* fracture. An example of a technical cohesion limit is the "true" breaking stress of a tension-test specimen, the breaking load divided by the sectional area at fracture. The cohesion limit thus obtained for a ductile metal, however, has been greatly altered by the plastic deformation. It is important to consider the cohesion limit of the metal prior to this deformation, and the variation of the cohesive strength with plastic deformation. The relation between the cohesion limit and the corresponding flow stress† determines the ductility of a metal and the energy that it will absorb before fracture. In this paper, as in the previous paper,21 tensile stresses will be viewed as positive and compressive stresses as negative. The algebraically greatest principal stress will be designated S1, the least principal stress will be designated S3, and the intermediate principal stress will be designated S2. In the previous paper, attention was confined to stress combinations with two of the principal stresses equal (with the intermediate principal stress S2 equal either to S3 or S1). In this paper, consideration will also be given to the effect of stress combinations with all three principal stresses unequal. In the earlier sections of the paper (pp. 1 to 14), attention will be confined to stress combinations with

Jan 1, 1942

By C. G. Dunn

WITH respect to theories of recrystallization in metals plastically deformed, it has been said that the present status of this subject is far from satisfactory.1 It may also be said that before any mechanism of recrystallization for metals and alloys can be set forth in a satisfactory manner, there must be made available considerable data on orientation changes that occur during the deformation and recrystallization processes. Although extensive data have been published on recrystallization in single crystals and in polycrystalline specimens, more results of a type that can be classified according to simple orientation changes would be desirable in this complex field. It might even be said that before classifications are made according to types of orientation changes, it may be possible to classify a considerable amount of data into certain kinds of orientation states if groups of common or nearly common orientation occur. Methods for computing the probability of occurrence for various types of groups have been published2 and it has been pointed out in particular that it should be possible to analyze orientation data for high-order twin relationships between old and new grains even when agreement is not at all exact. In this connection, work on recrystallization in silicon ferrite reported in a paper concerned with complex groups of annealing twins' indicated that some data were consistent with primary nucleation occurring according to a second-order or a third-order twin transformation. However, further work in this latter direction was definitely needed. It is, therefore, the purpose of the present paper to report data and analyses for primary nucleation in silicon ferrite following small deformations that have been carried out at the Pittsfield Works' Laboratory of the General Electric Co. Analyses have been made with the aid of standard groups of twins that are reported elsewhere .4 PREPARATION OF SPECIMENS AND EXPERIMENTAL PROCEDURE The material used in the present investigation was taken' from the same heat of steel as that used in a prior report.3 The finished strip in both cases was made by the Allegheny-Ludlum Steel Corporation according to methods that produce a high degree of preferred crystal orientation. Samples with large grains had the following composition: 3.45 per cent Si, 0.003 C, 0.008 P, 0.020 S, 0.075 Mn, 0.031 Al and 0.072 Cu. Thickness of specimens was 0.012 inches. Plastic deformation was produced by cold-rolling the samples on a mill with

Jan 1, 1945

By W. Crafts, J. L. Lamont

Selection of an alloy steel for a heat-treated article has been facilitated by methods for the calculation of harden-ability,' as-quenched hardness and tempered tensile strength.2 Ductility and toughness may also be estimated if the steel is completely hardened on quenching, 5,6 and the present study was carried out in order to develop a basis for estimating the Izod impact strength of partially hardened steel. The investigation was directed toward the prediction of Izod impact strength in steels of normal commercial quality without consideration of special compositions or heat-treatments that might produce abnormal brittleness. It was found that Izod impact strength of alloy steel is controlled by hardness, degree of hardening on quenching, and grain size. In finegrained steels the impact strength for any given degree of hardening is inversely proportional to the tempered Rockwell C hardness, and the relation of impact strength to hardness is lowered by incomplete hardening. Calculation of the tensile strength and impact strength of heat-treating steels has shown that, except at very high strengths, tensile strength is raised by alloys without loss of impact strength whereas the tensile strength gained by higher carbon contents tends to be accom- panied by a disproportionate loss of toughness. Plain carbon steels give relatively low and unpredictable impact strength. The calculation is sufficiently accurate to be helpful in the selection of alloy steel, and common grades of alloy steel have been evaluated with respect to combinations of tensile strength and impact strength attainable after heat-treatment in sections from I to. 4 in. in diameter. Procedure The study of the relation of hardness to impact strength was based on test data derived from 24 heats from four producers. The steels included the following SAE and AISI compositions: 1020, 1030, 1040, 1340, 3310, 33167 4320, 43.30, 4340, 8620, 8630, 8640, 8720, 8730, 8740, 931°, 9317, 9440, 9917 and three high-alloy chromium-nickel-molybdenum steels. As far as is known, the steels tested were of normal commercial quality. They were supplied in 4-in. sections, which were forged to smaller sizes, prenormalized, and machined to final dimensions. Heat-treatment was carried out by heating to the usual austenitizing temperature for the grade of steel, holding for one hour per inch of thickness and quenching in still oil at room temperature. Previous work had indicated that this quenching treatment approximates a severity of H = 0.3; The bars were tempered as follows: 34 in., I in., and 1% in., 2 hr; 235 in., 3 hr; 4 in., ; hr. All bars were air-cooled from the tempering tem-

Jan 1, 1948

By J. L. Lamont, W. Crafts

Selection of an alloy steel for a heat-treated article has been facilitated by methods for the calculation of harden-ability,' as-quenched hardness and tempered tensile strength.2 Ductility and toughness may also be estimated if the steel is completely hardened on quenching, 5,6 and the present study was carried out in order to develop a basis for estimating the Izod impact strength of partially hardened steel. The investigation was directed toward the prediction of Izod impact strength in steels of normal commercial quality without consideration of special compositions or heat-treatments that might produce abnormal brittleness. It was found that Izod impact strength of alloy steel is controlled by hardness, degree of hardening on quenching, and grain size. In finegrained steels the impact strength for any given degree of hardening is inversely proportional to the tempered Rockwell C hardness, and the relation of impact strength to hardness is lowered by incomplete hardening. Calculation of the tensile strength and impact strength of heat-treating steels has shown that, except at very high strengths, tensile strength is raised by alloys without loss of impact strength whereas the tensile strength gained by higher carbon contents tends to be accom- panied by a disproportionate loss of toughness. Plain carbon steels give relatively low and unpredictable impact strength. The calculation is sufficiently accurate to be helpful in the selection of alloy steel, and common grades of alloy steel have been evaluated with respect to combinations of tensile strength and impact strength attainable after heat-treatment in sections from I to. 4 in. in diameter. Procedure The study of the relation of hardness to impact strength was based on test data derived from 24 heats from four producers. The steels included the following SAE and AISI compositions: 1020, 1030, 1040, 1340, 3310, 33167 4320, 43.30, 4340, 8620, 8630, 8640, 8720, 8730, 8740, 931°, 9317, 9440, 9917 and three high-alloy chromium-nickel-molybdenum steels. As far as is known, the steels tested were of normal commercial quality. They were supplied in 4-in. sections, which were forged to smaller sizes, prenormalized, and machined to final dimensions. Heat-treatment was carried out by heating to the usual austenitizing temperature for the grade of steel, holding for one hour per inch of thickness and quenching in still oil at room temperature. Previous work had indicated that this quenching treatment approximates a severity of H = 0.3; The bars were tempered as follows: 34 in., I in., and 1% in., 2 hr; 235 in., 3 hr; 4 in., ; hr. All bars were air-cooled from the tempering tem-

Jan 1, 1948

By Carl A. Zapffe, M. Eleanor Haslem

The present investigation has three principal purposes: 1. To develop a method for measuring hydrogen embrittlement that avoids cer, tain errors complicating previously used methods. 2. To explore in a preliminary way some of the fundamental factors controlling embrittlement. 3. To apply the measurements specifically to stainless grades of steel, whose sensitivity or insensitivity to hydrogen embrittlement has never been clearly defined. Selecting a Test Method Hydrogen embrittlement is a condition of low ductility resulting from excessive absorption of hydrogen by the steel at some period in its history, and may be revealed by almost any test involving cold deformation. Tensile tests, impact tests, and bend tests are commonly used for detecting hydrogen embrittlement; although numerous other tests, such as cold-upsetting or extrusion, could be used. The simplicity of using a wire specimen for cathodic and acid pickling tests, and the especial adaptability of the bend test to wire specimens, led to selection of the bend test for the present research. Bend tests usually have been of three general types: (I) fatigue, (2) reversed bend, and (3) single bend. The first two types, though widely used, are inaccurate because their measurements are counteracted by an aging effect; and the third type has not been developed to its fullest utility. The effect of cold-working in removing hydrogen is well known. During a bend test hydrogen can be observed escaping from the convex side simply by coating the specimen with oil; and any technique employing flexing or reverse bending may therefore have its measurements masked because the mechanical action reduces the embrittlement during the test. This factor is so important that even elastic flexing of a hydrogen-charged wire specimen should be avoided before testing if accurate measurements are desired. Developing a Machine for Measuring Hydrogen Embrittlement As for the single-bend test, its theory is good, and recovery caused by mechanical work is kept to a minimum. With a given degree of hydrogen embrittlement, a specimen will break at a given angle if the bending is applied unidirectionally and uniformly. The radius of the bend must be kept constant; and the rate of bending should be a constant, slow enough to allow reading of the breaking angle, and yet rapid enough to prevent significant recovery from the escape of hydrogen during bending. A simple apparatus (Fig. I) was constructed using a type H Foxboro drive unit A, which is a synchronous motor with a gear-reduction ratio of 600 to I. A cord, fixed at one end to a wooden pulley B on the drive shaft of the motor, follows the pe-

Jan 1, 1947

By Carl A. Zapffe, M. Eleanor Haslem

The present investigation has three principal purposes: 1. To develop a method for measuring hydrogen embrittlement that avoids cer, tain errors complicating previously used methods. 2. To explore in a preliminary way some of the fundamental factors controlling embrittlement. 3. To apply the measurements specifically to stainless grades of steel, whose sensitivity or insensitivity to hydrogen embrittlement has never been clearly defined. Selecting a Test Method Hydrogen embrittlement is a condition of low ductility resulting from excessive absorption of hydrogen by the steel at some period in its history, and may be revealed by almost any test involving cold deformation. Tensile tests, impact tests, and bend tests are commonly used for detecting hydrogen embrittlement; although numerous other tests, such as cold-upsetting or extrusion, could be used. The simplicity of using a wire specimen for cathodic and acid pickling tests, and the especial adaptability of the bend test to wire specimens, led to selection of the bend test for the present research. Bend tests usually have been of three general types: (I) fatigue, (2) reversed bend, and (3) single bend. The first two types, though widely used, are inaccurate because their measurements are counteracted by an aging effect; and the third type has not been developed to its fullest utility. The effect of cold-working in removing hydrogen is well known. During a bend test hydrogen can be observed escaping from the convex side simply by coating the specimen with oil; and any technique employing flexing or reverse bending may therefore have its measurements masked because the mechanical action reduces the embrittlement during the test. This factor is so important that even elastic flexing of a hydrogen-charged wire specimen should be avoided before testing if accurate measurements are desired. Developing a Machine for Measuring Hydrogen Embrittlement As for the single-bend test, its theory is good, and recovery caused by mechanical work is kept to a minimum. With a given degree of hydrogen embrittlement, a specimen will break at a given angle if the bending is applied unidirectionally and uniformly. The radius of the bend must be kept constant; and the rate of bending should be a constant, slow enough to allow reading of the breaking angle, and yet rapid enough to prevent significant recovery from the escape of hydrogen during bending. A simple apparatus (Fig. I) was constructed using a type H Foxboro drive unit A, which is a synchronous motor with a gear-reduction ratio of 600 to I. A cord, fixed at one end to a wooden pulley B on the drive shaft of the motor, follows the pe-

Jan 1, 1947

By J. D. Mote, A. Rosen, J. E. Dorn

The effect of strain rate and temperature on the critical resolved shear stress for (1100) [1120] prismatic slip was determined for the intermediate hexagonal phase containing about 67 at. pct Ag and 33 at. pct Al. Whereas the flow stress increased only slightly as the test temperature was first decreased below room temperature, a rapid increase inflow stress was obtained with yet greater decreases in temperature from about 240" to 4°K. The effect of both temperature and strain rate on the flow stress over the low-temperature range could be completely rationalized in terms of the Peierls mechanism when the deformation is controlled by the rate of nucleation of pairs of kinks. A few years ago Mote, Tanaka, and Dorn1 observed that the critical resolved shear stress for prismatic slip of a 67 at. pct Ag plus 33 at. pct A1 hexagonal intermediate phase by the (1100)[1120] mode decreased precipitously as the test temperature was increased from 4" to about 160°K. Their results for both basal and prismatic slip are given in Fig. 1. It is obvious that only the flow stress for prismatic slip is strongly temperature-dependent, whereas the flow stress for basal slip is independent of temperature. If the temperature dependence of the flow stress were primarily due to interstitial impurities, it might be expected that they would influence the flow stress for basal slip as well. Since the activation volume at 115°K for prismatic slip was determined to be about 15b3, where b is the Burgers' vector, this thermally activated deformation process was tentatively ascribed as being due to the Peierls mechanism. But the various analyses of the Peierls mechanism then available as formulated by Seeger2 and also by Lothe and Hirth3 did not agree well with the experimental data. Since that time a more realistic theory for the operation of the Peierls mechanism under conditions where the strain rate is determined by the rate of nucleation of pairs of kinks has been presented by Dorn and Rajnak.4 The present investigation was, therefore, undertaken in order to provide the essential data for a careful check on the agreement between this theory and the low-temperature deformation by prismatid slip of the above-mentioned Ag2A1 intermediate phase. EXPERIMENTAL TECHNIQUE Single-crystal specimens so oriented that the [1120] direction and the normal to the (1100) plane were at 45 * 2 deg to the tensile axis were grown from the congruent melting composition of about Ag2Al for the intermediate hexagonal phase by the

Jan 1, 1964

By J. W. Craig, H. L. Walker

Industry has for many years recognized the dependence of certain mechanical and physical properties. as well as workability, upon grain size variations in brass. Although the dependence of properties upon grain size has been recognized there are not many instances where a planned program of testing has been conducted and where the only intentional variable has been grain size. In particular the literature is limited with respect to the effect of grain size on the endurance limit, though there are many industrial applications where the brasses are subjected to cycles of repetitive stresses. Literature A number of the physical and mechanical properties of a given brass sheet, in the annealed condition, will depend upon: (I) The ready-to-finish grain size before final rolling, (2) the percentage deformation by cold working, and (3) the time and temperature of annealing. The first and second variables affect the recrystallized grain size, and the third variable affects the coalesced grain size. Gibbsl has shown the effect of two different ready-to-finish grain sizes upon the tensile strength and hardness of deep drawing brass strip after a definite amount of cold rolling. The smaller the ready-to-finish grain size, the higher the tensile strength and hardness, but with lowered ductility, Gibbs also demonstrated, for a given time and temperature of anneal, that the tensile strength, hardness, and elastic limit are higher for the smaller ready-to-finish grain size, but the elongation is lowered. Townsend and Greena112 have reported data which show that cold working increases the tensile strength, hardness, and load carrying ability of deep drawing brass sheet under reversed stress. Greenall and Gohn3 have reported data which show that the smaller grain sizes have higher tensile strength and hardness properties, and the data also show that increased cold working increases the tensile strength and hardness properties of deep drawing brass sheet. Kommers4 has reported data for tests of brass of known ready-to-finish grain size, a specific amount of cold reduction, and annealed at different temperatures above and below the recrystallization temperature. Kommers' results indicate that annealing below the recrystallization temperature does not change the tensile strength and hardness properties, but the endurance limit may be increased from 22,000 to 28,000 psi. The increased endurance limit is explained as resulting from the reduction of internal stresses by a stress-relief anneal. Burghoff5 and associates have reported data on creep tests, over

Jan 1, 1949

By R. C. Ku, R. G. Davies

The stress-strain behavior of Fe-C and Fe-Ni solid-solution alloys has been investigated at 25°C. It is found that the rate of solid-solution strengthening is dependent upon the strain at which the yield stress is measured, the macroyield stress being much more concentration-dependent than the microyield stress. In fact the addition of nickel does not lead to any increase in the microyield stress of iron. The primary effect of increasing the carbon or nickel content is to increase the slope of the stress-strain curve in the microyield region; this effect has been correlated, by means of transmission electron microscopy, with a decreased ability of the dislocations to cross-slip. It is concluded that the Mott-Nabarro theory is a good description of true solid-solution hardening in these and other iron-base alloys. A.LL theories of the solid-solution strengthening1-4 indicate that the flow stress of an alloy increases both with solute concentration and "misfit" between the solvent and solute atoms. The functional relationship between strength, solute concentration, C, and misfit depends upon the particular theory. Mott and Nabarro1,2 and Schoeck and Seeger3 both predict a linear increase in strength with concentration, while Fleischer4 indicates that the strength should be proportional to C1/2; there are in the literature experimental observations to support both these compositional dependencies.1'8 The experimental evidence used to support the theories is the change in macroscopic yield stress (strain, e, = 10-3) with composition. However, recent investigations have revealed that solid-solution strengthening in a Cu-Al single crystals7 and in Fe-V polycrystal-line" alloys depends upon the strain at which the flow stress is measured; a flow stress in the microplastic range (e = 10-6 to 10-5) is much less concentration-dependent than the macroyield stress. Since the theories of solid-solution strengthening are concerned in particular with the stress to move a dislocation in a dislocation-free matrix, they should only be compared with microyield-stress data; it will be shown that in a material deforming homogeneously the microyield stress (e = 10-6) is approximately the stress to move through the matrix those dislocations which have been nucleated by stress concentrations such as particles or grain boundary ledges.9-11 In contrast, the macro-yield stress is more complex in that it is affected by several phenomena: dislocation multiplication, dislocation interactions, and the ease of propagating slip across grain boundaries. For example, it is experimentally observed that when long-range order12'13 or solute effects10 restrict cross alip the grain boundary

Jan 1, 1967

By Alexander Squire

A brief study of the effects of material and processing variations upon the tensile properties of steel formed from mixtures of iron and carbon was made in order to provide information regarding the properties obtainable in iron-carbon compacts as influenced by forming pressure, sintering temperature, and graphite particle size. Sintered steels formed from mixtures of iron and graphite have been studied by Stern,' who investigated the effect of various percentages of graphite on compacts formed from electrolytic iron that were repressed and heat-treated after sintering. A further study, by Stern and Greenberg,l is concerned with the heat-treatment of steels formed by the car-burization of iron compacts, and Margolies3 has reported work on the simultaneous sintering and carburization of iron-powder parts. Glauch4 investigated the effect of various types of graphite on the properties of iron-carbon powder alloys but did not determine the effect of different particle sizes of the same graphite alloyed with different types of powder. In the investigation reported in this paper, powders typical of those produced by electrolytic deposition and the decar-burization of shotted steel scrap were used. The powders were mixed by tumbling in a jar mill with graphite powder ground to an average particle diameter of 2, 4, 6, and 16 microns (as determined by microscopic measurement). The properties of the iron and graphite powders are presented in tabular form as Table I. In order to obtain the maximum information from a minimum number of test specimens, the study was divided into two sections with one set of specimens treated identically in each section as a basis for comparison. In the first section, iron powder produced by the shotting and subsequent decarburization of scrap steel was mixed with 2-micron graphite powder, pressed at 50,000, 100,-000, and 200,000 psi, and sintered in hydrogen at 1200°C for the periods of time ranging from 15 to 120 minutes. In the second section of the investigation, electrolytic iron powder was mixed with graphite of an average particle diameter of 2, 4, 6, and 16 microns, pressed at 100,000 psi, and sintered at temperatures ranging from 1000° to r200°C'. for periods of time of 30 to 180 minutes. By following this procedure an indication of the effect of the following variables upon the density and tensile properties of iron-carbon powder compacts was obtained: (I) forming pressure, (2) sintering time, (3) particle size of graphite powder, (4) sintering temperature, (4) type of iron powder.

Jan 1, 1947

By Alexander Squire

A brief study of the effects of material and processing variations upon the tensile properties of steel formed from mixtures of iron and carbon was made in order to provide information regarding the properties obtainable in iron-carbon compacts as influenced by forming pressure, sintering temperature, and graphite particle size. Sintered steels formed from mixtures of iron and graphite have been studied by Stern,' who investigated the effect of various percentages of graphite on compacts formed from electrolytic iron that were repressed and heat-treated after sintering. A further study, by Stern and Greenberg,l is concerned with the heat-treatment of steels formed by the car-burization of iron compacts, and Margolies3 has reported work on the simultaneous sintering and carburization of iron-powder parts. Glauch4 investigated the effect of various types of graphite on the properties of iron-carbon powder alloys but did not determine the effect of different particle sizes of the same graphite alloyed with different types of powder. In the investigation reported in this paper, powders typical of those produced by electrolytic deposition and the decar-burization of shotted steel scrap were used. The powders were mixed by tumbling in a jar mill with graphite powder ground to an average particle diameter of 2, 4, 6, and 16 microns (as determined by microscopic measurement). The properties of the iron and graphite powders are presented in tabular form as Table I. In order to obtain the maximum information from a minimum number of test specimens, the study was divided into two sections with one set of specimens treated identically in each section as a basis for comparison. In the first section, iron powder produced by the shotting and subsequent decarburization of scrap steel was mixed with 2-micron graphite powder, pressed at 50,000, 100,-000, and 200,000 psi, and sintered in hydrogen at 1200°C for the periods of time ranging from 15 to 120 minutes. In the second section of the investigation, electrolytic iron powder was mixed with graphite of an average particle diameter of 2, 4, 6, and 16 microns, pressed at 100,000 psi, and sintered at temperatures ranging from 1000° to r200°C'. for periods of time of 30 to 180 minutes. By following this procedure an indication of the effect of the following variables upon the density and tensile properties of iron-carbon powder compacts was obtained: (I) forming pressure, (2) sintering time, (3) particle size of graphite powder, (4) sintering temperature, (4) type of iron powder.

Jan 1, 1947

By Holbrook G. Botset

It is possible by means of the electrolytic model to simulate water-flooding or gas recycling systems involving input and output wells, and also the encroachment of a natural water drive. The results are obtained pic-torially, and by simple measurements and calculations the percentage of recovery is obtained qualitatively as a function of the total input. Introduction The increased demand for petroleum products, together with the decline in discovery rate and the higher cost of recovery as deeper formations are brought into production, has stimulated interest in methods for studying and predicting efficiencies of various production programs. Among methods Of recovery that have become of increased significance recently are gas recycling in condensate fields and secondary recovery by water-flooding. The electrolytic model is a useful device for studying such methods in the laboratory, at least in a qualitative way. The original experiments with electrolytic models and the development of their application to the study of secondary reCoverY problems were published in 1933. 1,2,3 Subsequently other investigators continued the development and modification of the bait method, with resultant improvements and extension of its applications.4-7 The method and equipment to be described here are thought to represent still further improvement in the results obtainable, with increased validity in their application to field problems. Sand OF Principles of Operation The underlying theory of the operation of the model is given in references I, 2 and 3. However, a brief statement of principles involved is given herewith. The applicability of the model is based on the fact that Ohm's law and d'Arcy's law are exactly analogous; whence, electrical flow through a conducting medium may be used to simulate homogeneous fluid flow through a permeable medium. If two electrodes are placed in a conducting (ionized) solution and connected to the positive and negative terminals of a source of direct current, the positive ions of the solution will move toward the negative terminal, Since the velocity of an ion in an electrolytic medium is proportional to the electrical gradient, just as the velocity of a fluid particle in a porous medium is proportional to the pressure gradient, the motion of the ions in the potential field will be the same as the motion of fluid particles in a porous medium if the positive and negative terminals (input and output wells) and boundary conditions are made equivalent in shape and distribution. In order for the analogy to hold exactly, the sand must be assumed to have uniform porosity and permeability and the input

Jan 1, 1946

By Holbrook G. Botset

It is possible by means of the electrolytic model to simulate water-flooding or gas recycling systems involving input and output wells, and also the encroachment of a natural water drive. The results are obtained pic-torially, and by simple measurements and calculations the percentage of recovery is obtained qualitatively as a function of the total input. Introduction The increased demand for petroleum products, together with the decline in discovery rate and the higher cost of recovery as deeper formations are brought into production, has stimulated interest in methods for studying and predicting efficiencies of various production programs. Among methods Of recovery that have become of increased significance recently are gas recycling in condensate fields and secondary recovery by water-flooding. The electrolytic model is a useful device for studying such methods in the laboratory, at least in a qualitative way. The original experiments with electrolytic models and the development of their application to the study of secondary reCoverY problems were published in 1933. 1,2,3 Subsequently other investigators continued the development and modification of the bait method, with resultant improvements and extension of its applications.4-7 The method and equipment to be described here are thought to represent still further improvement in the results obtainable, with increased validity in their application to field problems. Sand OF Principles of Operation The underlying theory of the operation of the model is given in references I, 2 and 3. However, a brief statement of principles involved is given herewith. The applicability of the model is based on the fact that Ohm's law and d'Arcy's law are exactly analogous; whence, electrical flow through a conducting medium may be used to simulate homogeneous fluid flow through a permeable medium. If two electrodes are placed in a conducting (ionized) solution and connected to the positive and negative terminals of a source of direct current, the positive ions of the solution will move toward the negative terminal, Since the velocity of an ion in an electrolytic medium is proportional to the electrical gradient, just as the velocity of a fluid particle in a porous medium is proportional to the pressure gradient, the motion of the ions in the potential field will be the same as the motion of fluid particles in a porous medium if the positive and negative terminals (input and output wells) and boundary conditions are made equivalent in shape and distribution. In order for the analogy to hold exactly, the sand must be assumed to have uniform porosity and permeability and the input

Jan 1, 1946

By William J. Craig, Harold L. Walker

INDUSTRY has for many years recognized the dependence of certain mechanical and physical properties, as well as workability, upon grain size variations in brass. Although the dependence of properties upon grain size has been recognized there are not many instances where a planned program of testing has been conducted and where the only intentional variable has been grain size. In particular the literature is limited with respect to the effect of grain- size on the endurance limit, though there are many industrial applications where the brasses are subjected to cycles of repetitive stresses. LITERATURE A number of the physical and mechanical properties of a given brass sheet, in the annealed condition, will depend upon: (I) The ready-to-finish grain size before final rolling, (2) the percentage deformation by cold working, and (3) the time and temperature of annealing, The first and second variables affect the recrystallized grain size, and the third variable affects the coalesced grain size. Gibbs1 has shown the effect of two different ready-to-finish grain sizes upon the tensile strength and hardness of deep drawing brass strip after a definite amount of cold rolling. The smaller the ready-to-finish grain size, the higher the tensile strength and hardness, but with lowered ductility, Gibbs also demonstrated, for a given time and temperature of anneal, that the tensile strength, hardness, and elastic limit are higher for the smaller ready-to-finish grain size, but the elongation is lowered, Townsend and Greenall2 have reported data which show that cold working increases the tensile strength, hardness, and load carrying ability of deep drawing brass sheet under reversed stress. Greenall and Gohn3 have reported data which show that the smaller grain sizes have higher tensile strength and hardness properties, and the data also show that increased cold working increases the tensile strength and hardness properties of deep drawing brass sheet. Kommers4 has reported data for tests of brass of known ready-to-finish grain size, a specific amount of cold reduction, and annealed at different temperatures above and below the recrystallization temperature. Kommers' results indicate that annealing below the recrystallization temperature does not change the tensile strength and hardness properties, but the endurance limit may be increased from 22,000 to 28,000 psi. The increased endurance limit is explained as resulting from the reduction of internal stresses by a stress-relief anneal. Burghoff5 and associates have reported data on creep tests, over

Jan 1, 1948

By Howard C. Dunkle

Various factors can affect the quality of BIII2 and BIII3 steel as produced in a bessemer plant; among them: vessel-charging practice, blowing practice, ingot-pouring practice, ingot delivery-time practice, pit-heating practices, and ingot-rolling practice. Evaluation of the influence of ingot delivery time on quality has been chosen as the subject for this paper because this time is completely within the control of the operator, and on this particular factor there is a tremendous amount of information in the dusty archives of the average steel plant. In order to know how much improvement can be made and when attention should be directed to other factors that influence quality, in the continual struggle for improvement, the effect of ingot delivery time must be accurately evaluated. Once this is done, the importance of other variables can be accurately obtained, thus eliminating the necessity of resorting to opinions that are of doubtful value at best. In the study described herein, extensive use was made of the statistical card system as a method of determining the effect of ingot delivery time as a quality factor in bessemer screw-stock grades by simple direct correlation. The value of this statistical method as a means of accurately determining the influence of various factors has been amply demonstrated by Work1 for the bessemer process and by Hand and Gould2 and Fetters and Chipman3 for the open-hearth process. The quality records of 300,000 tons of bessemer screw-stock billets were used in this study of the effect of ingot delivery time on the rejections for breaks, pipe, check and seams. The reduction in the number of rejections for poor quality reduces the costs and increases the productivity per man-hour. The operator today, more than ever before, must know how to keep costs down, how to do it most quickly and in the best way, and how to obtain the highest quality in line with the ever increasing demands of the customer. It is necessary for him to know the individual relations and interrelations between various factors affecting the quality of the manufactured product if he is to produce material that will meet competitively the cost, performance, and quality demands of the trade. Significance of Steel Manganese, Mixer Silicon and Steel Sulphur as Quality Factors In order to obtain the highest grade of material it is necessary to control many factors—not just one or two, as operators

Jan 1, 1945

By Eleanor Haslem, Carl A. Zapffe

THE present investigation has three principal purposes: I. To develop a method for measuring hydrogen embrittlement that avoids certain errors complicating previously used methods. 2. To explore in a preliminary way some of the fundamental factors controlling embrittlement. 3. To apply the measurements specifically to stainless grades of steel, whose sensitivity or insensitivity to hydrogen embrittlement has never been clearly defined. SELECTING A TEST METHOD Hydrogen embrittlement is a condition of low ductility resulting from excessive absorption of hydrogen by the steel at some period in its history, and may be revealed by almost any test involving cold deformation. Tensile tests, impact tests, and bend tests are commonly used for detecting hydrogen embrittlement; although numerous other tests, such as cold-upsetting or extrusion, could be used. The simplicity of using a wire specimen for cathodic and acid pickling tests, and the especial adaptability of the bend test to wire specimens, led to selection of the bend test for the present research. Bend tests usually have been of three general types: (I) fatigue, (2) reversed bend, and (3) single bend. The first two types, though widely used, are inaccurate because their measurements are counteracted by an aging effect; and the third type has not been developed to its fullest utility. The effect of cold-working in removing hydrogen is well known. During a bend test hydrogen can be observed escaping from the convex side simply by coating the specimen with oil; and any technique employing flexing or reverse bending may therefore have its measurements masked because the mechanical action reduces the embrittlement during the test. This factor is so important that even elastic flexing of a hydrogen-charged wire specimen should be avoided before testing if accurate measurements are desired. DEVELOPING A MACHINE FOR MEASURING HYDROGEN EMBRITTLEMENT As for the single-bend test, its theory is good, and recovery caused by mechanical work is kept to a minimum. With a given degree of hydrogen embrittlement, a specimen will break at a given angle if the bending is applied unidirectionally and uniformly. The radius of the bend must be kept constant; and the rate of bending should be a constant, slow enough to allow reading of the breaking angle, and yet rapid enough to prevent significant recovery from the escape of hydrogen during bending. A simple apparatus (Fig. I) was constructed using a type H Foxboro drive unit A, which is a synchronous motor with a gear-reduction ratio of 600 to I. A cord, fixed at one end to a wooden pulley B on the drive shaft of the motor, follows the pe-

Jan 1, 1946

By L. D. Wooddy, Robert Moscrip

The simultaneous solution of the volumerric balance and the unsteady-state equation has been used for several years to make performance calculations for combination drive reservoirs. This method makes possible the calculation of volumetric changes of fluids in the gas cap, oil zone, and aquifer which occur as a result of withdrawals and reservoir pressure changes. It does not provide a means for the determination of reservoir fluid distribution changes corresponding to these vollrmetric changes. A knowledge of the fluid saturation distribution in the reservoir at various stages of depletion is important for the determination of the efficiency of gas and water as oil-displacement media and, therefore, for the reliable predicrion of ultimate oil recovery. To provide this knowledge, the displacement equations are solved simultaneously with the volumetric balance and unsteady-state equations. The described calculation procedure has been used satisfactorily to analyze the past performance and to predict the future behavior of combination drive reservoirs under both primary and pressure-maintenance operations. INTRODUCTION The three basic mechanisms by which oil is displaced from a reservoir are: (1) dissolved gas drive—the displacement of oil by the expansion of liberated solution gas, (2) water drive—the displacement of oil by water which enters the oil zone from the aquifer, and (3) gas cap drive—the displacement of oil by gas which ex- pands into the oil zone from the gas cap. The action of gravitational forces may be effective in increasing the efficiency of the basic drive mechanisms. Gravitational forces favor the segregation both of gas and oil and of oil and water, thus tending to shorten the transition zone between oil and displacing fluids. Most reservoirs produce under the influence of a combination of these drives and are designated "combination drive reservoirs". Fig. 1 is a cross section of a typical combination drive reservoir. A calculation procedure for analyzing the performance of combination drive reservoirs has been developed by combining the displacement equations' with the volumetric balance equation' and the unsteady-state equations. The pressure-production performance and the positions of the gas-oil and oil-water contacts are calculated for several stages of reservoir depletion by solving these equations simultaneously, thus affording a basis for: 1. Determining instantaneous and ultimate oil, gas, and water production under various operating conditions. 2. 'Establishing a maximum efficient rate of production, 3. Determining the advantages of pressure maintenance and unitization, and 4. Designing surface installations necessary for primarv and pressure-maintenance operations. DEFINITIONS The calculation procedure for combination drive res-

Jan 1, 1957

By N. A. D. Parlee

THE gas-liquid metal diffusion cell technique1-3 has been used to study the diffusion of nitrogen in Fe-C alloys. The actual apparatus and technique were the same as employed by the authors to study the diffusion of hydrogen in liquid iron.' The diffusion cell' was formed by immersing an alumina tube in a stagnant melt contained in an alumina crucible. The tube (hereafter called absorption tube) contained nitrogen gas at 1 atm and was connected to a sensitive gas-measuring system. The change in the average concentration of nitrogen in the melt in the absorption tube was determined by measuring the rate of absorption of nitrogen in the diffusion cell. Eq. [I], 1-3 derived from the appropriate solution of Fick's second law, was used to examine the data and to calculate chemical diffusion coefficients (D) in situations where the absorption appeared to be controlled by diffusion in the liquid: where V is the stp volume in cu cm, d is the diffusion cell diameter in cm, p, is the density of the melt in g per cu cm, pg is the stp density of nitrogen in g per cu cm, C, is expressed in wt pct, D is in sq cm per sec, and t is in min. According to Eq. [I], a plot of v vs vt should yield a straight line passing through the origin if absorption is controlled by diffusion in the liquid. The slope of this line could be used to determine the value of D under appropriate conditions. As discussed in earlier reports,1,2 the initial thermal expansion of the gas upon immersing the absorption tube distorts the line in the initial stages of a diffusion experiment. However, this is not a serious problem since the slope of V vs 6 plots can be determined from the data points obtained after the initial expansion ceases. The volumes reported on the data plot presented here represent absorption after this thermal expansion ceased. Several preliminary diffusion experiments were attempted with melts of pure iron and with Fe-C alloys containing up to 0.6 pct C. In these cases, no or very little absorption was observed. The only data obtained were for an Fe-C melt which was in addition thoroughly deoxidized by successive hydrogen and vacuum-degassing treatments. These treatments introduced an appreciable amount of aluminum into the melt and reduced its omgen content. The original charge material for this melt contained 0.23 pct s and approximately 0.001 pct &. After repeated hydrogen and vacuum-degassing treatments two diffusion experiments were performed. The analysis of the melt

Jan 1, 1968

By John R. Lewis

DURING the past few years there has been considerable interest in the sizing and the preparation of the iron ore fed into blast furnaces. Furnacemen know that proper sizing of ore tends to increase the efficiency of the furnace. It has been shown by Joseph1 and his associates that there is a direct relationship between the porosity of an ore particle and the time required for its reduction in the blast furnace. This relationship may be stated as follows: All other factors remaining constant, the time for reduction of a given sample of ore is inversely proportional to its porosity. As a consequence, large pieces of very porous ore, say 3 or 4 in. in cross section, will be completely reduced by the time they reach the hot zone just above the tuyeres, while large pieces of dense, nonporous ore may reach the hot zone with their centers unreduced. This means that for the latter complete reduction will be accomplished by the so-called "direct method;" i.e., where carbon reacts directly with the ore. Some recent work by Philbrook2 seems to contradict this rule. He found that of two unlike ores he studied, the one with the lower porosity reduced more readily. He explained his results as "possibly due to an apparently greater tendency of the `A' ore (lower porosity) to crack during preliminary dehydration and during reduction." This brings his results in line with the rule stated above. It is not the author's intention to enter into a discussion of the merits of "direct" versus "indirect" reduction. It is enough to say that, in general, indirect reduction is desirable. For the greatest efficiency, Gruner's theorem3 requires that all reduction in the blast furnace be indirect. Joseph seems to believe this also, because in his recent article on Some Comparisons between Iron Ore, Sinter and Nodules as Blast Furnace Feed' he concludes that: "In general, the carbon in blast-furnace coke is used most efficiently when the largest amount of the carbon charged reaches the tuyeres." However, P. V. Martin,' in an excellent paper, has shown that some direct reduction may actually increase the efficiency of the furnace; that is, increase its rate of production while maintaining maximum fuel economy. For nonporous ores there is more opportunity to have an excess of direct reduction unless the factors that make for indirect reduction are favored; for instance; the proper sizing of the ore particles. Another factor that has an important bearing on the reduction rate, as it is affected by particle size, is the flow of heat into the particle. The ore particle

Jan 1, 1947