Search Documents

By J. Washburn, R. Drouard, E. R. Parker

Temperature dependence of the rate of recovery in zinc single crystals after a simple shear deformation at low temperature was investigated. Some tentative suggestions regarding the annealed and strain-hardened states of a crystal are discussed. RECOVERY may be defined as the gradual return of the mechanical and physical properties of strain-hardened metal to those characteristic of the annealed material; an increase in temperature increases the rate of recovery. The annealing process in strain-hardened polycrystalline metals is complicated by the inhomogeneity of strain which always exists in aggregates. Polygonization in bent regions of the crystals and growth of new almost strain-free grains starting at points of severe local distortion1-:' make it almost impossible to isolate and study the recovery process. Homogeneously strained single crystals, however, do not polygonize or re-crystallize and hence they can be used advantageously to study recovery. In such crystals strain hardening is completely removed by recovery alone. Since recovery is a process whereby certain lattice disturbances introduced by plastic flow are gradually reduced, a knowledge of the rate and temperature dependence of this process for various conditions of prestrain might be helpful in formulating a model of the strain-hardened state. For simplicity it seemed desirable to limit the type of prestrain to the simplest obtainable, i.e., simple shear strain. In the experiments to be described, recovery was studied by observing changes in the stress-strain curve of prestrained zinc single crystals held for various times at temperatures above that employed for straining. Single crystals were grown from the melt by a modified Bridgeman technique from Horse Head Special zinc 99.99 pct pure, and from spectrographically pure zinc 99.999 pct pure. They were grown as 1 in. diameter spheres and acid-machined' to the final specimen contour. The test section was a cylinder about 1/8 in. high and 3/4 in. in diameter. The conical sections adjacent to the test section were cemented into the grips so the load could be transmitted to the crystal as uniformly as possible. The specimens were oriented so that in testing the maximum shear stress was applied along one of the slip directions, [2110], in the (0001) plane. Details of the production and testing of such specimens have been presented.' Each test was carried out according to the following schedule: 1—The crystal was strained at — 50°C until it reached a maximum shear stress, ,,,. The strain rate was approximately 5 pct per min in all cases. 2—After straining, the crystal was unloaded before the temperature was changed. Unloading required about 3 min. 3—The temperature of the specimen was then increased from — 50°C to the temperature, T, of recovery. This change in temperature was completed in a time of less than 2 min. The specimen remained at temperature, T, for a time, t, which differed for the various specimens. 4—Thereafter the temperature was again reduced to — 50 °C in approximately 3 min. 5—While at —50°C, the stress-strain curve after recovery was obtained. 6—The specimen was then unloaded and annealed for 1 hr at 375 °C in a helium atmosphere to bring about complete recovery. Cooling to room temperature after anneal required 90 min. 7—The same crystal could be re-used for another test because the plastic properties after annealing closely duplicated those of the original crystal. The specimen was immersed during the test in a bath of methyl alcohol which, through a system of tubes, could be pumped through either of two heat exchangers to regulate the temperature; this was accomplished by circulating the liquid through coils immersed in a bath of acetone and dry ice for cooling or in a bath of warm water for heating. Test temperatures were thus maintained constant within ±1°C. The — 50°C temperature was low enough so that no measurable recovery occurred during unloading and reloading. The stress-strain curve continued after recovery along a path below, but approximately parallel to, the path of a curve obtained in an uninterrupted test. Fig. 1 shows some of the results from a specimen of 99.999 pct Zn. The amount of downward displacement of the curve due to recovery was a

Jan 1, 1954

Discussion of the paper of F. M. Simonds and E. Z. Burns, presented at the New York Meeting, February, 1913, and printed in Bulletin No. 75, March, 1913, pp. 369 to 402. W. L. SAUNDERS, New York,. N. Y.:-Mr. Burns in his native Colorado modesty has said that he apologizes for things left out of this paper. I am much impressed by what he has put into the paper, as of all the papers that I have read on the subject, describing, as it does, a specific piece of work that has been accomplished, I do not recall one that gives so much information in such a practical way. Mr. Burns has also said that it is very hard to get men to put things down while the work is being driven. My experience is that it is very much harder to get the men in charge of work of this kind to bring them in in the form of a report before a body of engineers after the work is done. We have a great many cases where records are kept in much detail, but they are usually kept under cover, with the mistaken idea that the information gained is private information for the benefit of those who have done the work. Messrs. Simonds and Burns have opened up this case so that we can get the benefit of that experience which they have had, and so that we can learn something for the future. The description contained in this paper, as I have said, is a very practical one. You will notice in going through it. that the authors have given in detail a record of their work from the beginning to the end, and they even go so far as to publish an exact copy of the Rawley Mining Co.'s daily report. That daily report is something which those of us who are engaged in similar work might copy to great advantage, and having it before us we can check up our men while doing work and exact from them equal conditions, if it is possible to do so.

Jan 5, 1913

By A. Spilners, M. Simnad

The rates of formation of the different oxides on molybdenum in pure oxygen at 1 atm pressure have been determined in the temperature range 500° to 770°C. The rate of vaporization of MOO, is linear with time, and the energy of activation for its vaporization is 53,000 cal per mol below 650°C and 89,600 cal per mol at temperatures above 650°C. The ratio Mo03(vapor.lzing)/MoOS3(suriace) increases in a complicated manner with time and temperature. There is a maximum in the total rate of oxidation at 6W°C. At temperatures below 600°C, an activation energy of 48,900 cal per mol for the formation of total MOO, on molybdenum has been evaluated. The suboxide Moo2 does not increase beyond a very small critical thickness. At temperatures above 725°C, catastrophic oxidation of an autocatalytic nature was encountered. Pronounced pitting of the metal was found to occur in the temperature range 550° to 650°C. Marker movement experiments indicate that the oxides on molybdenum grow almost entirely by diffusion of oxygen anions. USEFUL life of molybdenum in air at elevated temperatures is limited by the unprotective nature of its oxide which begins to volatilize at moderate temperatures. Although the oxide/metal volume ratio is greater than one, the protective nature of the oxide film is very limited. Gulbransen and Hickman' have shown, by means of electron diffraction studies, that the oxides formed during the oxidation of molybdenum are MOO, and MOO,. The dioxide is the one present next to the metal surface and the trioxide is formed by the oxidation of the dioxide. Molybdenum dioxide is a brownish-black oxide which can be reduced by hydrogen at about 500°C. Molybdenum trioxide has a colorless transparent rhombic crystal structure when sublimed, but on the metal surface it has a yellowish-white fibrous structure. It is reported to be volatile at temperatures above 500" and melts at 795°C. It is soluble in ammonia, which does not affect the dioxide or the metal. In his extensive and classic investigations of the oxidation of metals, Gulbransen2 has studied the formation of thin oxide films on molybdenum in the temperature range 250" to 523°C. These experiments were carried out in a vacuum microbalance, and the effect of pressure (in the range 10-6 yo 76 mm Hg), surface preparation, concentration of inert gas in the lattice, cycling procedures in temperature, and vacuum effect were studied. The oxidation was found to follow the parabolic law from 250" to 450°C and deviations started to occur at 450 °C. The rates of evaporation of a thick oxide film were also studied at temperatures of 474" to 523°C. In vacua of the order of 10- km Hg and at elevated temperatures, an oxidation process was observed, since the oxide that formed at these low pressures consisted of MOO, which has a protective action to further reaction in vacua at temperatures up to 1000°C. Electron diffraction studies showed that, as the film thickened in the low temperature range, MOO8 became predominant on the surface. Above 400°C MOO, was no longer observed, MOO, being the only oxide detected. The failure to detect MOO, on the surface of the film formed at the higher temperatures does not militate against the formation of this oxide, since according to free energy data MOO3, is stable up to much higher temperatures. At the low pressures employed, this oxide would volatilize off as soon as it was formed. Its vapor pressure is relatively high and is given by the equations" log p(mm iig) = -16,140 T-1 -5.53 log T + 30.69 (25°C—melting point) log p(mm He) = -14,560 T-1 -7.04 log T+1 + 34.07 (melting-boiling point). Lustman4 has reported some results on the scaling of molybdenum in air which indicate a discontinuity at the melting point of MOO, (795°C). Above the melting point of MOO,, oxidation is accompanied by loss of weight, since the oxide formed flows off the surface as soon as it is formed.5,6 Qathenau and Meijering7 point out that the eutectic MOO2-MOO3 melts at 778C, and they ascribe the catastrophic oxidation of alloys of high molybdenum content to the formation of low melting point eutectics of MOO3 with the oxides of the melts present. Fontana and Leslie -explain the same phenomenon in terms of the volatility of MOO,, which leads to the formation of a porous scale. Recent unpublished work by Speiser9 n the oxidation of molybdenum in air at temperatures between 480" and 960°C shows that the rate of weight change of molybdenum is controlled by the relationship between the rates of formation and evaporation of MOO,. They have measured the rates of evaporation of Moo3 in air at different temperatures and estimated an activation energy of 46,900 cal. This compares with the value of 50,800 cal per mol obtained by Gulbransen for the rate of sublimation of MOO, into a vacuum.

Jan 1, 1956

By K. C. Gilbart, E. Stansfield

This test was described in a privately circulated First Progress Report on Slacking Characteristics of Coal, by A. C. Fieldner and W. A. Selvig, May 1, 1928. The test was described in detail in U. S. Bureau of Mines Report of Investigation 3055, in November, 1930,1 The test, in brief, is conducted as follows: A sample of freshly mined coal consisting of 18 to 25 pieces approximating 1 1/4 cubes, and weighing 500 to 600 grams, is taken for the test. The sample is subjected to a "blank sieving" of carefully regulated degree, on an 8-in. circular sieve with 0.263-in. square openings, and the undersize and oversize weighed. The oversize is placed on a sheet-iron pan and dried for about 24 hr. in an A.S.T.M. air-drying oven maintained at 30" to 35" C. through which a current of warm air is drawn. The sample is then cooled to room temperature and immersed for one hour in water at the same temperature. The water is then drained off, the sample dried for 24 hr. as before, cooled, sieved as before, and the oversize and undersize weighed. The percentage weight of the undersize is calculated and reported as the first cycle loss. This loss, corrected by subtracting the percentage loss in the blank sieving, is termed the slacking index. The sample may be subjected to further cycles of wetting, draining, air-drying, sieving and weighing. In a letter (August, 1932) W. A. Selvig approved making the blank sieving on a duplicate sample, rather than on the sample used for the test, where sufficient coal was available. This method is now employed in these laboratories. The accelerated weathering test has been employed in the laboratories of the Research Council of Alberta, at Edmonton, since 1928, but not found entirely satisfactory as repeat determinations with samples taken from the same or adjacent mines frequently showed serious differences. Differences must be expected as the coal may vary in the seam, and the selection of a typical set of lumps approximating 1 1/4-in. cubes

Jan 1, 1934

By P. A. Laxen, H. R. Spedden, A. M. Gaudin

WHEN a mineral particle is fractured, bonds between the atoms are broken. The unsatisfied forces that appear at the newly formed surface1 are considered to be responsible for the adsorption of ions at the mineral surface. A knowledge of the mechanism and extent of ion sorption from solution onto a mineral surface is of interest in the development of the theory of flotation.2,3 Study of the adsorption of sodium from an aqueous solution on quartz offers a simple approach to this complicated problem. The availability of a radioisotope as a tracer element meant that accurate data could be obtained.4,5 Three main factors which appeared likely to affect the adsorption of sodium are: 1-concentration of sodium in the solution, 2-concentration of other cations in the solution, and 3-anions present in the solution. Hydrogen and hydroxyl ions are always present in an aqueous solution. By controlling the pH, the concentration of these two ions was kept constant. The variation in the amount of sodium adsorbed with variation in sodium concentration was then determined under conditions standardized in regard to hydrogen ion. The effect of concentration of hydrogen ions and of other cations was also measured. A few experiments were made to get a preliminary idea on the effect of anions. The active isotope of sodium was available as sodium nitrate. Standard sodium nitrate solutions were used throughout these experiments except when the effects of other anions were studied. It was found that sodium adsorption increased with sodium-ion concentration, but less rapidly than in proportion to it. Increasing hydrogen-ion concentration, or conversely decreasing hydroxylion, brings about a comparatively slight decrease in sodium-ion adsorption. Increasing the concentration of cations other than hydrogen or sodium decreases somewhat the adsorption of sodium ion. It would appear as if the kind of anion is a secondary factor in guiding the amount of sodium ion that is adsorbed. Materials and Methods Quartz The quartz was prepared as in previous work in the Robert H. Richards Mineral Engineering Laboratory4 except for the refinement of using de-ionized distilled water for the final washing of the sized quartz, prior to drying5 To minimize the laborious preparation of quartz, experiments were made to determine whether the sodium-covered quartz could be washed free of sodium and re-used. The experiments were successful as indicated by lack of Na' activity on the repurified material and by its characteristic sodium adsorption. Table I gives the spectrographic analyses of the quartz used. The quartz ranged from 16 to 40 microns in size, averaging about 23 microns (microscope measurement), and had a surface of 1850 sq cm per g (lot I), 2210 (lot II) and 2000 (lot III) as determined by the Bloecher method.6 Radioactive Sodium Method of Beta Counting for Adsorbed Sodium: Na22, the radioisotope of sodium, possesses convenient properties.7 It has a half-life of 3 years, thus requiring no allowance for decay during an experiment. On decay it emits a 0.575 mev ß radiation and a 1.30 mev ? radiation. The decay scheme is illustrated in the following equation: [Y Nam S. - 'Net 3 years] The ß radiation is sufficiently strong to penetrate an end-window type of Geiger-Mueller counting tube. This, in turn, makes it possible to use external counting, a great advantage in technique. Furthermore, it permits the assaying of solids arranged in infinite thickness, while assaying evaporated liquors on standardized planchets. The equipment used was standard and similar to that employed by Chang8 The original active material was 1 ml of solution containing 1 millicurie of Na22 as nitrate. This active solution was diluted to 1000 ml. Five milliliters of this diluted active solution was found to give a quartz sample a sufficiently high activity for accurate evaluation of the sodium partition in the adsorption measurements. Also, 1 ml of final solution gave a sufficiently high count for precision on the liquor analyses. The sodium concentration of the diluted active solution was 1.2 mg per liter, so that 6 mg of sodium for 60 ml of test solution and 12 g of quartz was the minimum amount used. The active solution was stored in a Saftepak bottle. Procedure for Adsorption Tests: The method consisted of agitating 12 g of quartz with 60 ml of solution of known sodium concentration for enough time to establish equilibrium between the solution and the quartz surface. The quartz was separated as completely as possible from the solution by filtering and centrifuging. The activity on the quartz and in the equilibrium solution was measured and the partition of the sodium was calculated from the resulting data. The detailed procedure for the adsorption test is set forth in a thesis by Laxen5 In brief, it included the following steps: 1-Ascertainment of linearity between concentration of Na22 and activity measured. 2-Evaluation of factor to translate activity on solid of infinite thickness in terms of activity on an evaporated active film of minute thickness, on the various shelves of the counter shield. 3-Taking precautions to avoid evaporation of water during centrifuging.

Jan 1, 1952

MINING AND METALLURGICAL SOCIETY OF AMERICA San Francisco Section The San Francisco Section of the Mining and Metallurgical Society of America held a joint meeting with the local section of the American Institute of Mining Engineers at the Engineers' Club, San Francisco, on Tuesday, Apr. 16, 1918. The meeting was preceded by a dinner. Letters from the parent body in NewYork asking for the consideration of the proposed bill before Congress, and an expression of opinion relative to the appointment of a Federal Administrator of Mines justified the joint meeting of the local sections of the two mining societies, in that a more representative opinion of the engineers of California could he obtained. The meeting was called to order at 7:15 P.M. by Mr. Frank H. Probert acting as Chairman. About thirty engineers were present. Mr. Probert read a letter of March 14, from Secretary Huntoon, asking that the meeting be called. He read excerpts from Bulletin 117 of February 28, 1918, of the Mining and Metallurgical Society containing a copy of the proposed bill, so that all present might be advised of its essential contents. He briefly commented on the urgent need of such legislation and invited discussion of the subject. After long and thorough discussion on the part of the members present, Professor Lawson made the following motion: I move that a resolution expressing the sense of the joint meeting of the local sections of the American Institute of Mining Engineers and Mining and Metallurgical Society of America be forwarded to the secretaries of the two societies to the effect that we heartily approve of the purpose and intention of the bill designed to promote and stimulate the production of minerals necessary for the successful prosecution of the war; and that we suggest prices should be fixed for the period of the war and two years thereafter, and that these prices, guaranteed by the Government, should apply at the nearest shipping point to place of production of the minerals. This motion was carried. The meeting then adjourned, and a telegram was sent by Mr. Probert, the Chairman, to Mr. Huntoon, notifying him of the motion that had been carried at the meeting.

Jan 7, 1918

By Charles E. Lundin

The character of the Er-D system was established by determining pressure-temperature-composition relationships. A Sieuerts&apos; apparatus was employed to make measurements in the temperature range, 473" to 1223"K, the composition range of erbium to ErD3, and the pressure range of 10~s to 760 Torr. The system is characterized by three homogeneous phase regions: the nzetal-rich, the dideuteride, and the trideuteride phases. These phases and their solubility boundaries were deduced from the family of isotherms of the system zchich relate the pressure-temperature-composition variables. The equilibrium plateau decomposition relationships in the two-phase regions were determined from can&apos;t Hoff plots to be: The differential heats of reaction in these two regions are AH = - 53.0 * 0.2 and -20.0 *0.1 kcal per mole of D2, respecticely. The differential entropies of reaction are AS = - 36.3 * 0.2 and - 31.0 * 0.2 cal per mole D2. deg, respectively. Relative partial molal and intepal thermodynamic quantities were calculated from the pure metal to the dideuteride phase. The study of the Er-D system was undertaken as a logical complement to an earlier study of the Er-H system.&apos; The primary interest was to compare the characteristics of the two systems and relate the difference to the isotopic effect. Studies of rare earth-deuterium systems by other investigators have been very limited in number and scope. Furthermore, there is even less information available wherein an investigator has systematically compared a binary rare earth-hydrogen system with the corresponding rare earth-deuterium system. The available information consists primarily of dissociation pressure measurements in the plateau pressure region of a few rare earths. Warf and Korst&apos; determined dissociation pressure relationships for the La- and Ce-D systems in the plateau region and several isotherms for each system in the dideuteride region. They compared these data with those of the corresponding hydrided systems. The study of these systems as a whole was very cursory and did not give sufficient data for a thorough comparison of the effect of the hydrogen vs the deuterium in the respective rare earths. The heat capacities and related thermodynamic functions of the intermediate phases, YH, and YD2, were determined by Flotow, Osborne, and Otto,~ and the investigation was again repeated for YH3 and YD3 by Flotow, Osborne, Otto, and Abraham.4 This investigation studied only these specific phases. Jones, Southall, and Goodhead5 surveyed the hydrides and deu-terides of a series of rare earths for thermal stability including erbium. They experimentally determined isotherms of selected hydrides and plateau dissociation pressures for deuterides. These data allowed comparison of the enthalpy and entropies of formation of the dihydrides and dideuterides. To date, no one rare earth has been selected to thoroughly establish the complete pressure-temperature-composition (PTC) relationships of binary solute additions of hydrogen and deuterium, respectively. The objective in this investigation was to provide the first comparison of a complete family of isotherms of a rare earth-deuterium system with those of a rare earth-hydrogen system. This would allow one to determine what differences exist, if any, in the various phase boundaries and the thermodynamic relationships in various regions of the systems. I) EXPERIMENTAL PROCEDURE A Sieverts&apos; apparatus was employed to conduct the experimental measurements. Briefly, it consisted of a source of pure deuterium, a precision gas-measuring buret, a heated reaction chamber, a mercury manometer, and two McLeod gages (a CVC, GMl00A and a CVC, GM110). Pure deuterium was obtained by passing deuterium through a heated Pd-Ag thimble. A 100-ml precision gas buret graduated to 0.1-ml divisions was used to measure and admit deuterium to the reaction chamber. The reaction unit consisted of a quartz tube surrounded by a nichrome-wound furnace. The furnace temperature was controlled by a recorder-controller to . An independent measurement of the sample temperature in the quartz tube was made by means of a chromel-alumel thermocouple situated outside, but adjacent to, the quartz tube near the specimen. Pressure in the manometer range was measured to k0.5 Torr and in the McLeod range (10~4 to 10 Torr) to *3 pct. The deuterium compositions in erbium were calculated in terms of deuterium-to-erbium atomic ratio. These compositions were estimated to be *0.01 D/Er ratio. The erbium metal was obtained from the Lunex Co. in the form of sponge. The metal was nuclear grade with a purity of 99.9+ pct. The oxygen content was reported to be 340 ppm and the nitrogen not detectable. Metallographically the structure was almost free of second phase (<i vol pct). A quantity of sponge was arc-melted for use as charge material. The solid material was compared with the sponge in the PTC relationships. They were found to be identical. Therefore, sponge material was used henceforth, so that equilibrium could be attained more rapidly. The specimen size was about 0.2 gr for each loading of the reaction chamber. The procedure employed to obtain the PTC data was to develop experimentally a family of isothermal curves of composition vs pressure. First, a specimen

Jan 1, 1969

By Jean-Jacques Prompsy, J. S. Rinehart

Some time ago a study was initiated at the Colorado School of Mines in an effort to arrive at a better understanding of the stress fields developed within drill bits under dynamic loading and the influence that these stress fields could have on the failure of the bits. Particular emphasis has been given to the influence that bit shape has on the establishment of highly localized, potentially destructive stress inhomogeneities within the bit. The study has been divided into three phases involving three velocity regimes: impacts at very low velocities, 0 to 20 ft/sec, a velocity range in which dynamic effects are just beginning to be found; impacts at velocities ranging from 20 to several hundred ft/sec, a range commonly encountered in practical drilling operations; and impulsive loading through the detonation of explosives, a region in which the dynamic effects are greatly exaggerated and made more identifiable. The ultimate objective is to provide basic data which will enable the mitigation through judicious design of the frequency and severity of these transient concentrations of intense stress, thereby prolonging and increasing drill efficiency. This paper presents results of the third phase of this study — the development of a better understanding of the dynamics and mechanics of failures caused by transient stress-wave interactions. The impulsive loading or transient waves in these experiments were generated by detonating small explosive charges placed on the ends of Plexiglas cylindrical rods terminating in truncated cones. Under such intense loading, dynamic effects are greatly exaggerated and, hence, made more identifiable. The explosion generates a high-intensity transient stress disturbance which moves through the rod, reflects from surfaces which lie in its path, and establishes momentarily narrow regions of high concentrations of stress where failure of fracture may occur. The peregrinations of these waves, their interactions and their effects have already been described in the literature (see, for example, Refs. 1 and 2). The locations and extent of the regions quite apparently are strongly dependent on specimen shape, making it possible through judicious shaping of specimens to relocate the highly stressed regions, minimize their extent, or eliminate them entirely. These experiments were designed, first, to identify more clearly the vulnerable regions in geometries relevant to drill-bit design and, then, to modify these regions in a predictable way by changing specimen shape. Through this latter process, it is anticipated that better bit design might evolve. The specimens used in the experiments were cylindrical rods, 1 1/2 and 1 1/8 in. in diameter, ended by a truncated cone, with the cone angles ranging from 45° to 130°. Upper cone face diameters were 1/2, 3/4, or 1 in. A small plastic-covered electric blasting cap detonated on the axis of the specimen produced the spherical shock wave. The detonators used were Olin Mathieson No. 6, which induced into the rod a transient saw-toothed stress disturbance of about 3-microseconds duration, corresponding to a wave length of 0.3 in. in the Plexiglas. Five distinct systems of fracture were observed: (1) along the axis of the rod, a lower system of fractures, the cracks focusing around one point for specimens having cone angles of 80° and 90° and, as the cone angle was increased, spreading downward; (2) just above these fractures, an upper system of fractures composed of horizontal cracks observable in some specimens but not of any appreciable extent; (3) a third system of axial cracks still above the latter, observable in the small cone-angle specimens; (4) in the upper part of the specimen, a system of radial fractures extending from the blasting point; and (5) circular spalling due to reflection of the wave on the boundary of the cylinder. Only the first three systems, the axial fractures, are examined here. LOWER TENSILE FRACTURE SYSTEM The first, lower system of tensile fractures, shown in the photograph of Fig. 1, was observed in almost all of the specimens. It was due to the reflected tensile wave coming in from the boundary of the cylinder as shown in Fig. 2. The reflected wave was cylindrically convergent and focused

By B. B. Cox

Iraq, formerly called Mesopotamia in Asiatic Turkey, became a kingdom under British Mandate after the world war and is expected to gain its independence in 1932 when it enters the League of Nations. The kingdom is shown on Fig. 1 in its relations to neighboring countries, to the Mediterranean Sea and to the Persian Gulf. It is slightly smaller than the State of Texas with its capitol, Baghdad, inland about as far from the Persian Gulf as Breckinridge, Tex., is from the Houston Shipping Channel. The oil fields lie 180 to 225 miles north of Baghdad, or about as far as from Breckinridge to Oklahoma City, and about as far from the Mediterranean as Fort Worth is from Hobbs, N. M. A narrow-gage railway runs from Basra, the Persian Gulf port, to Baghdad. From there another narrow-gage runs into the Kurdish hills east of the Tigris to Kirkuk. A standard-gage, part of the old Berlin-Baghdad system, follows the west bank of the Tigris northward from Baghdad to Baiji, a village about 100 miles south of Mosul. No railway exists between Iraq and the Mediterranean, though the Anatolian Railways in southern Turkey come to within 50 miles of the Iraq frontier and 120 miles of Mosul. Surveys have been completed for a railway through British Mandates from Haifa to Baghdad as well as for a railway through French Mandated Syria from Tripoli to Abu Kemal near the Iraq border. Wagon roads, excepting those constructed by the oil companies, are few and indifferent in Iraq and no road exists across the desert to the Mediterranean, but contrary to prevalent beliefs the surface is firm and free from sand dunes so that motor cars can go almost anywhere in dry weather, with ease. Frequent motor car and airplane service exists between Baghdad and the Mediterranean ports and motor car service may be had between Kirkuk and Nisibin, Turkey, where on two days each week through Wagons Lits service is available to Paris. Baghdad is about 21 days distant from New York City with present transport facilities. The climate is semiarid, similar to Imperial Valley, California, the average rainfall outside the mountainous parts amounting generally to

Jan 1, 1932

By Charles Baker

THE district of Catorce, San Luis Potosi, ranks among the first half-dozen silver-producing camps f Mexico. Mining has been more or less continuous there for 150 years. The large producing mines, Mapum, Mazapil, Palomas, Musquiz, Minas Virjas, now for the most part idle or abandoned, are grouped around the head of two valleys: one, which drains to the west, falls 2000 ft. (609.6 m.) in 4 1/2 mi. (7.2 km.) between the main Catorce and the western foot of the range and is characterized by steep canon walls; the other, east of the main town of Catorce from which it is separated by a high divide, heads in a number of steep tributaries above the basin in which lies the town of Potrero and flows nearly north for 10 mi. (16 km.) to the northern base of the range; below Potrero, it has for the most part gently sloping valley walls and a broad valley floor. The Sierra Catorce is the highest range of the region, the summits reaching altitudes of over 11,000 ft. With the exception of a few cliffs of the erosion escarpment of the lower limestone and the canon walls below the main town of Catorce, which is the highest town in Mexico, the gently rounded slopes are characteristic of a maturely eroded mountain range composed of folded sedimentary rocks. As is usual in desert regions, the heavy-bedded limestones are the most resistant to erosive forces. Folded into anticlines, they form the mountain ranges; and the intermontane valleys and basins, originally carved out of less resistant shales, clays, marls and sandstones, are covered by debris forming a mantle with surface gradually rising upwards toward the hills. In time, the debris buries, in deposits formed from their own ruins, all but the highest summits of the original mountains; some f this region has already nearly reached this stage. Most of the debris is firmly cemented by calcium carbonate (caliche). Solution f the limestone by meteoric waters afforded the supply of lime carbonate, which has been redeposited upon evaporation of the waters as a cement binding the boulders, pebbles, and finer detritus.

Jan 9, 1921

By John Jan

Iodine is a soft, lustrous, grayish-black non- metallic element with a density of 4.9. It is the least active of the four members of the halogen family. The other members are, in order of increasing activity, bromine, chlorine, and fluorine. Iodine is a solid at ordinary temperatures, while bromine is a liquid and chlorine and fluorine are gases. Iodine melts at 113°C and volatilizes at 184.4°C to a blue- violet gas with an irritating odor. It occurs in nature only as iodates and iodides or other combined forms. It was discovered by Bernard Courtois in France in 1811, who noticed its presence as an unknown substance in crude soda ash obtained from burning seaweed. Gay-Lussac recognized it as a new element and named it iode, from the Greek word "ioeides or iodes" for violet color (MacMillan, 1970). The world production is not known with any great certainty, but it is probably between 20 and 25 million lb per year, of which about 25% is consumed in the United States. Geology and Mineralogy Iodine compounds occur as a minor constituent as a mineral in the Chilean nitrate deposits and in solution in brines and sea- water. According to the U.S. Geological Survey, it is the 47th most abundant element in the earth&apos;s crust. The minerals lautarite, Ca (10,) (calcium iodate), and dietzeite, Ca, (10,) , (CrO,) , (calcium iodate-chromate) are found in Chilean nitrate deposits which are located in Antofagasta and Tarapach provinces on the eastern slope of the coast range in a desert area. Various brines contain iodine compounds. Seawater contains about 0.05 ppm of iodine and some seaweeds will extract and accumulate it up to 0.45% on a dry basis. Some coals in West Germany also contain iodine compounds. The known and potential sources of iodine reported in 1968 are given in [Table 1]. Iodine has been recovered from brines in Java, Indonesia, France, England, and the USSR. Iodine has also been recovered from seaweed in Ireland, Scotland, France, Japan, Norway, and the USSR. The indicated re- serves and future resources of iodine are large but have never been adequately measured. Analysis Iodine as the free element can be detected by the characteristic blue color it gives to a starch solution. Quantitatively it is determined as the free element by titration with standard thiosulfate solutions using starch as an indicator. Colorimetric methods are also applicable.

Jan 1, 1975

On. Tuesday, Apr. 8, the Rocky Mountain Club held its 12th annual dinner at the Waldorf-Astoria, New York. In reporting the dinner the Evening Telegram says: "General Coleman du Pont was sort of master of ceremonies, and he conducted the affair at the end of a Colt .45. It was the General&apos;s `forty-five&apos; which filled the banquet hall of the Waldorf-Astoria with the brand of smoke which Uncle Sam showered so generously upon Germany&apos;s hordes. It was General du Pont&apos;s `forty-five&apos; which bellowed and thundered and echoed through Fifth avenue, scaring horses and shell shocking pedestrians: But no one was hurt or badly shocked except those who could not discern the artistry of Miss Doraldino&apos;s dance. "There were Western men around the table who have just come hack from over there. For instance, there were Brigadier General G. H. McManus, General Shanks and a score of others. And there were Thomas H. Watkins, who is said to own half the State of Pennsylvania and is known as the `Coal Baron&apos;-of Pennsylvania,, and Alba B. Johnson, president of the Baldwin Locomotive Works, each one a Westerner, with personality and type suggestive of some of the wonderful men Bret Harte wrote so much about. "It seemed as though General du Pont, who was chairman of the Reception Committee, tried to eclipse all former meetings, and he succeeded if congratulations are a criterion. " General du Pont startled the management of the Waldorf and surprised the diners by staging a three-round bout between Frankie Fay and Phil Wagner. The clash between these two featherweights made Waldorf history, because it was the first boxing contest ever held in the hotel. Tex Rickard, who is going to chaperone Jess Willard and Jack Dempsey in a fight in the near future,-was scheduled to referee the contest, but at the last moment, for some obvious reason, M. E. Schermerhorn was sent in as third man. The bout was a slashing one. Miss Amparito Farrar, lately returned from France, where-she sang for the &apos;dough-boys;&apos; Eleanore Wetmore, the Rath Brothers and Phil Baker were among the others who entertained.

Jan 5, 1919

Discussion of the paper of O. P. Hood, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 94, October, 1914, pp. 2607 to 2611. R. V. Norris, Wilkes-Barre, Pa.-I have had a little experience with gasoline locomotives and I want to indorse very strongly Mr. Hood&apos;s point with regard to the danger of carbon monoxide poisoning. I think .the terrible danger is not fully realized. I was foolish enough some time ago, in investigating a gasoline locomotive, to attempt to walk out of the mine entry behind it, and for several days I felt very seriously the carbon monoxide effects. The use of gasoline locomotives ought to be confined to mine entries where there is a very large amount of air. One of the grave dangers is their great convenience and the temptation to run them into chambers for just a few moments to get a car or two. GEORGE S. RICE, Pittsburgh, Pa.-Apparently one of the great dangers is in the style of the gasoline engine. When my attention was. first directed to the type of gasoline locomotives which I saw in the foreign mines-France, Belgium, and Germany, I was most favorably impressed with them, and they have given no trouble on account of fumes, so far as I could learn. Large numbers of them were being used, but all were of small capacity, and of a kind in which the speed control is by a governor of the hit-or-miss type, the engine running continuously. Their power capacity was very low, if I remember correctly it was not over 4 or 5 h.p., but they were used under favorable conditions where the grades in the mines were slight, since the entries or tunnels bad a slight grade in favor of-the load, making about the same pull for the empties against the grade as for the load with the grade. I understand the hit-or-miss valve arrangement enables a setting that will give more perfect combustion than can be insured with the valve controlled by the operating man, as in the automobile type of valve and engine used in this country. Apparently the European type of locomotive does not have the capacity to permit use under the conditions existing in this country, where most of our entries or tunnels have variable grades and long heavy trips of mine cars are used.

Jan 4, 1915

By V. Koump, T. F. Perzak, R. G. Olsson

The rate of dissolution of recrystallized alumina in molten iron oxide in equilibrium with iron at 1450°C was studied by rotating alumina disks in the melt. The samples were rotated from 1 to 12 min at speeds from 54 to 3270 rpm. It is concluded from the experimental results that the process is limited by diffusion in the liquid boundary layer. The interdiffusion coefficient for the dissolution of alumina disks in pure molten iron oxide was estimated to be about 3 xl0-5= sq cm per sec. THE erosion of refractory materials is of considerable importance in iron- and steelmaking processes. Since many refractories contain alumina, this investigation was undertaken to develop a further understanding of the erosion mechanism. Shurygin et al.1-3 have investigated the rate of dissolution of alumina in molten silicates and molten fluorides by rotating alumina disks in various melts. The rates were reported to be limited by diffusion in the liquid boundary layer. In the present investigation the rate of dissolution of alumina in molten iron oxide in equilibrium with iron was studied in a similar manner; alumina disks were rotated at different speeds in molten iron oxide at 1450°C. The relationship between the rate of dissolution of the flat surface of the disk and the speed of rotation was used to determine whether the process is limited by diffusion in the liquid boundary layer or by some chemical reaction mechanism. APPARATUS AND EXPERIMENTAL PROCEDURE A schematic diagram of the experimental apparatus is shown in Fig. 1. The iron oxide melts were contained in 2-in.-diam high-purity iron crucibles that were centered in a cylindrical graphite susceptor. Prior to each sequence of experiments, sufficient reagent-grade ferric oxide was added to a crucible to form approximately 350 g of molten iron oxide; the depth of the melt was about 11/2 in. To prevent excessive erosion of the crucible, about 70 pct of the required iron was added to the crucible in the form of iron powder. The mixture was melted in an atmosphere of purified argon by induction heating with a 250-kc generator. After the oxide was molten, a Pt/Pt-10 pct Rh thermocouple at the exterior of the crucible was calibrated against an iron-sheathed thermocouple immersed in the melt and was thereafter used to regulate the melt temperature. All experiments were conducted at 1450°C with a probable error of 10°C. The alumina disks were constructed from pure re-crystallized alumina having a density of 3.7 g per cu cm (porosity approximately 6 pct). For each disk sample a 1-cm-diam alumina cylinder of known length (0.9 to 1.0 cm) was cemented into a ground seat at the end of a 1.27-cm-OD centerless ground alumina tube. The ends of the tube and cylinder were flush and served as the disk surface. When mounted in the apparatus the alumina tube was guided by tungsten carbide bearings and rotated by a variable-speed motor. The bearing and drive assembly could be raised and lowered in order to allow the sample to be quickly moved in and out of the melt. At the start of an experiment, a sample was preheated for several minutes directly above the melt, and then immersed in the middle of the melt to a depth of a in. and rotated for 1 to 12 min at speeds of 64 to 3270 rpm. The speed of rotation was measured by a hand tachometer. At the start and completion of each experiment, a melt sample was withdrawn with a cold copper rod and the alumina content was determined by chemical analysis. During individual experiments the alumina concentration of the melt changed by the order of 0.25 wt pct. Average melt compositions for individual experiments were used in the subsequent computations and were in the range between 0.12 and 4.3 wt pct alumina. The extent of dissolution was determined by sectioning the end of the sample and measuring the final length of the alumina cylinder with a microscope. Since the exposed end of the cylinder, i.e., the disk surface, was etched in a manner characteristic of this geometry, a number of measurements were made on

Jan 1, 1969

Iron Ores and Blast Furnace Practice Concentration of Iron Ores in the United States. By T. R. Counselman. (Metals Technolog), December 1943) Selection of Blast-furnace Refractories. By Hobart M. KrANer and E. B. Snyder. (Metals Technology, April 1944) The Washing of Pittsburgh Coking Coals and Results Obtained on Blast Furnaces. By C. 1). King. (Metals Technology, September 1943) Steelmaking The Role of Basic Slags in the Elimination of Phosphorus from Steel. By Richard L. BArrett and William J. McCaughey. (Metals Technology, April 1944) The Relative Deoxidizing Power of Boron In Liquid Steel and the Elimination of Boron in the Open-hearth Process. By B. W. Gurry. (Metals &apos;Technology, December 1943) Manufacture and Properties of Killed Bessemer Steel. By C. C. Wright. (Metals Technology, June 1944) Hardenability Effect of Sixteen Alloying Elements on Hardenability of Steel. By Irvin R. Kramer, Robert Hafner and Stewart L. Toleman. (Metals Technology, September 1943) Effect of Quenching Temperature on the Results of the End-quench Hardenability Test. By Clarence E. Jackson and Arthur L. Chrjstenson. (Metals Technology, December 1943) Effect of Some Elements on Hardenability. By Walter Crafts and John L. Lamont. (Metals Technology, January 1944) Effect of Several Variables on the Hardenability of High-carbon Steels. By I?. S. Rowland, J. Welchner and R. IS. Marshall. (Metals Technology, January 1944) Mechanical Properties Influence of Hydrogen on Mechanical Properties of Some Low-carbon Manganese-iron Alloys and on Hadfield Manganese Steel. By Herbert H. Uhlig. (Metals Technology, June 1944) Aging and the Yield Point in Steel. By J. R. LOW, Jr., and 14. Gensamer. (Metals Technology, December 1943) Tensile Properties of Medium-carbon Low-alloy Cast Steels. By H. A. Schwartz and W. Kenneth Bock. (Metals Technology, August 1944) Variables Affecting the Results of Notched-bar 1mpct Tests on Steels. By CLarence 15. Jackson, MYRon A. Pugancz and Frank S. McKenna. (Metals Technology, August 1944) The Notched-bar Lmpact Test. By John H. Hollomon. (Meta1s Technology, April 1944) Hardness Measurement as a Rapid Means for Determining Carbon Content of Carhon and Low- alloy Steels. By K. L. Clark and NIcHols Kowall. (Metals Technology, January 1944)

Jan 1, 1944

Iron Ores and Blast Furnace Practice Concentration of Iron Ores in the United States. By T. R. Counselman. (Metals Technolog), December 1943) Selection of Blast-furnace Refractories. By Hobart M. KrANer and E. B. Snyder. (Metals Technology, April 1944) The Washing of Pittsburgh Coking Coals and Results Obtained on Blast Furnaces. By C. 1). King. (Metals Technology, September 1943) Steelmaking The Role of Basic Slags in the Elimination of Phosphorus from Steel. By Richard L. BArrett and William J. McCaughey. (Metals Technology, April 1944) The Relative Deoxidizing Power of Boron In Liquid Steel and the Elimination of Boron in the Open-hearth Process. By B. W. Gurry. (Metals &apos;Technology, December 1943) Manufacture and Properties of Killed Bessemer Steel. By C. C. Wright. (Metals Technology, June 1944) Hardenability Effect of Sixteen Alloying Elements on Hardenability of Steel. By Irvin R. Kramer, Robert Hafner and Stewart L. Toleman. (Metals Technology, September 1943) Effect of Quenching Temperature on the Results of the End-quench Hardenability Test. By Clarence E. Jackson and Arthur L. Chrjstenson. (Metals Technology, December 1943) Effect of Some Elements on Hardenability. By Walter Crafts and John L. Lamont. (Metals Technology, January 1944) Effect of Several Variables on the Hardenability of High-carbon Steels. By I?. S. Rowland, J. Welchner and R. IS. Marshall. (Metals Technology, January 1944) Mechanical Properties Influence of Hydrogen on Mechanical Properties of Some Low-carbon Manganese-iron Alloys and on Hadfield Manganese Steel. By Herbert H. Uhlig. (Metals Technology, June 1944) Aging and the Yield Point in Steel. By J. R. LOW, Jr., and 14. Gensamer. (Metals Technology, December 1943) Tensile Properties of Medium-carbon Low-alloy Cast Steels. By H. A. Schwartz and W. Kenneth Bock. (Metals Technology, August 1944) Variables Affecting the Results of Notched-bar 1mpct Tests on Steels. By CLarence 15. Jackson, MYRon A. Pugancz and Frank S. McKenna. (Metals Technology, August 1944) The Notched-bar Lmpact Test. By John H. Hollomon. (Meta1s Technology, April 1944) Hardness Measurement as a Rapid Means for Determining Carbon Content of Carhon and Low- alloy Steels. By K. L. Clark and NIcHols Kowall. (Metals Technology, January 1944)

Jan 1, 1944

By A. Lee Barrett

THE Maintenance Committee of the Coal Division of the American Institute of Mining and Metallurgical Engineers is presenting as a part of this report the second of a series of maintenance cost comparisons. The committee&apos;s purpose is to assemble maintenance costs on all equipment connected with mechanical operations at the face of coal mining and to arrange these costs by districts so that comparisons can be made between districts and within districts. The committee, this year, sent 35 questionnaires to representative coal companies who either reported last year or had advised specifically of the inability to report to last year&apos;s questionnaire primarily because of limited time. The response to the questionnaire this year was not as good as last year, only 20 of the 35 selected companies returning a completed questionnaire. This year&apos;s data has been .compiled and combined with last year&apos;s data to present a comparison of the 1945 and 1946 costs of loading machines, shortwall cutting machines, universal cutting machines, service locomotives, shuttle cars, and mine cars. The same tabulation by districts is used as was used for 1945. As was indicated by last year&apos;s report there is considerable variation in the maintenance cost of mining machinery in the various coal mining districts and due to this high variability it was not felt practical to attempt to Arrive at weighted averages. Consequently, all average figures used in this report are straight averages. An analysis was made of companies reporting both this year and last year in an attempt to determine the trend in maintenance costs for different classes of equipment. Ten representative companies are used in this computation. Table I shows the average cost for 1945 and 1946. It is felt that the negative trend in the maintenance cost of universal cutting machines probably represents the effect of the purchase of a relatively large number o new machines in 1946 with little maintenance cost appearing during the first yeas of operation. The grand total figure indicates an upward trend amounting to plus 18.7 pct. However, this figure is viewer with some suspicion because of the effect of the universal cutters decreasing maintenance cost and it is concluded that direct application of percentage increase should be made to types of equipment. In Table 2 covering maintenance costs of various types of mining equipment for 1945 and 1946 the results, obtained in Table I indicating trends were applied to those

Jan 1, 1948

Discussion of the paper of F. C. LANGENBERG and R. G. WEBBER, presented at the New York meeting, February, 1915, and printed in Bulletin No. 98, February, 1915, pp. 291 to 300. HENRY M. HOWE, Bedford Hills, N. Y.-The results here given are of great interest and are welcome as forming another rivet to increase the stability of our present theories of the constitution and properties of steel. The important discovery is that the hysteresis increases with the fineness of the structure, that is to say with the extent of contact between the particles of ferrite and cementite. All of the specimens except No. 4 consist of ferrite and cementite of different degrees of intimacy of admixture. If hysteresis represents something akin to surface friction, which retards the rotation of the ferrite on the application and release of the magnetizing force, then it is only natural that it should increase as it does with the intimacy of admixture, because it is at the surface of contact of a given particle of ferrite with the neighboring particles of cementite that this friction is to be expected, and of course the extent of surface must in¬crease with the intimacy of admixture. The somewhat greater hardness of specimen 4 than of the others may perhaps he referred to the principle discussed in my paper, Why Does Lag Increase with the Temperature from Which Cooling Starts?&apos; The furnace-cooled specimens were cooled so slowly that the influence of the initial temperature of heating is effaced. But in the air-cooled specimens we have the suggestion that the high temperature, 1,000°, from which the cooling of No. 4 started has prevented the completion of the transformation, with the result that the metal is slightly harder than any of the others. The difference is not to be explained by difference in the fineness of structure, because the whole range of fineness from No. 1 to No. 6 is accompanied by no change in hardness, the only change being an appreciable increase of hardness following the air cooling from 1,000°.

Jan 5, 1915

A. M. CANDY,* Pittsburgh, Pa.-I think more stress should be laid upon the question of welding with the carbon electrode, which we ordinarily call graphite arc welding. Mr. Miller&apos;s photograph indicated that the original parent metal had been decarburized to a marked degree. It would be interesting to know the carbon content of the parent metal, and whether or not Mr. Miller has made any investigations to determine if the metal is always decarburized or whether in some instances we actually have carbon injected into the weld, which has been the understanding that has been quite prevalent. There were one or two other points that Mr. Miller brought out concerning which I desire to ask one or two questions: The illustrations that he presented were obtained with what, I suppose, would be termed a real low-carbon steel welding wire, which gives in the deposited metal grains that are more or less symmetrical, whereas the Roebling electrode, which is a mild steel of higher carbon content, apparently gives a columnar structure. I do not know which-of these I structures is more desirable, but assuming that the structure produced by the really low-carbon steel wire is the more desirable, would it not be true that the very low carbon content would, probably owing to high temperatures that prevail in the arc, result in a greater amount of oxidation and probably result in either carrying into the weld more oxide or producing more oxide on the surface as the operator progresses? The short arc is an advantage in all cases. Whether Mr. Miller&apos;s trouble is oxide or nitride, the short arc helps him out, because the closer the end of the electrode is to the work the less chance there is for either oxygen or nitrogen to get in. And whichever is the cause of the trouble, the short arc keeps it out by lessening the time in which the steel is molten and the amount of air that gets in. It also makes sure that the molten metal will not fall into the crater. Everything is in favor of the short arc.

Jan 4, 1919

By P. R. Hines

Diphenyl guanidine is used as an accelerator in vulcanizing rubber. Other rubber accelerators are also flotation collectors, e.g., dithiocarbamate, thiazole, and the xanthates. Urea and its derivatives are good flotation collectors,&apos; and guanidine is the nitrogen analog of urea. These two characteristics suggested testing diphenyl guanidine as a flotation collector. Diphenyl guanidine has been tried in flotation work previously, but references give no details.&apos;.&apos; Bunker Hill Co. of Kellogg, Idaho, supplied the ore sample used in these tests. The sample was typical of the ore milled in 1949 and contained 4.52 pct Pb and 1.08 pct Zn. A flotation test made by the author with potassium ethyl xanthate as a collector, the same flotation reagents, and the same grind employed in regular Bunker Hill mill practice was the standard for comparing results with the compounds and derivatives of guanidine. The compounds and derivatives of guanidine are only fair collectors of galena. However, if potassium ethyl xanthate were used in the galena float, its presence later in the sphalerite float would make it impossible to introduce another type of collector and be certain which collector contributed the result, so the compound or derivative of guanidine under test was used in both the galena and sphalerite floats in Table I. On both the galena and the sphalerite in the Bunker Hill ore, the depressing action of sodium cyanide and zinc sulfate is much greater with collectors of the guanidine type than with the xanthates. If the depressing agents are left out when a guanidine type of collector is used, but a pH of 8.6 is maintained with either lime or sodium carbonate, the depressing action is approximately the same as in the standard xanthate test. Consequently the depressing agents, sodium cyanide and zinc, were not used in the galena floats of tests 1226, 1228, and 1286, Table I, so the galena floats would be on a comparable basis with the standard xanthate test. As shown by the tests in Table I, the loss in the tail when diphenyl guanidine is used is 8.3 to 9.3 pct, as compared to 17.6 pct with potassium ethyl xanthate, or a recovery of 2.3 to 2.0 lb more zinc. Concentrate grade is 13.7 pct with potassium ethyl xanthate and increases to 22.9 and 31.8 pct with diphenyl guanidine, showing a much higher selectivity. Unless the Barrett&apos;s No. 4 coal tar creosote is considered to be a collector, no collector other than diphenyl guanidine is present in the tests, Nos. 1226, 1228, and 1286. Tests 1218, 1253, and 1263 in Table I1 were run to check the effect of the depressing agents used in flotation of the galena (sodium cyanide and zinc sulfate) upon subsequent flotation of sphalerite by diphenyl guanidine. Urea was substituted for potassium ethyl xanthate in tests 1253 and 1263 because it is a good collector for galena and a poor one for sphalerite, and the effect of the depressing agents is more marked with urea than with potassium ethyl xanthate. Test 1205 checks the effect of urea alone without any depressing agents when used for the flotation of galena. Table I1 shows that diphenyl guanidine as a collector for sphalerite is compatible with other flotation reagents used in floating galena. When the depressing agents sodium cyanide and zinc sulfate are used in the galena flotation step, the amount of lime in the sphalerite flotation must be increased (compare 1253 and 1263). Table I11 gives some of the compounds of guanidine which were tested and compared. Some of the compounds and derivatives of guanidine* are solu- * Diphenyl guanidine is in commercial production and is available on the market. ble in water and others are not. Those tested were fed dry. When an organic collector is promising, its compounds and derivatives should be tested and their comparative collecting power recorded. Eventually, in this way, it may be possible to discover some of the essential chemical characteristics of a good collector. For example, it is interesting to compare the diphenyl and dibutyl derivatives in Table IV with those of urea in Table 111, Example 3, U. S. Patent 2,664,198. All are good collectors. Table I shows some of the effects of lime on recovery of sphalerite by diphenyl guanidine. Table V

Jan 1, 1960