Search Documents

By John W. Wagner, Robert K. Willardson

Single crystals of Pbl-xSnxTe have been grown from nonstoichiometric, cation-rich melts with the objective of producing as-grown, bulk material containing carrier concentrations ranging from 1016 per cu cm to 1018 per cu cm. Three specific crystal composi-tions were investigated in detail; x = 0.00, 0.10, and 0.17. Pull rates of from I to 3 mm per hr were used. Single crystals were successfully pulled from melts containing as little as 30 at. pct Te. Hall coefficients, resistivities, and carrier mobilities of these materials were determined. The relationship between the composition of the melt and the carrier concentration in the as-grown crystal has been studied for the three crystal compositions of interest. BULK single crystals of Pb,-,Sn,Te have previously been grown from stoichiometric melts.1,2 Such crystals are p-type and have relatively high carrier concentrations ranging from -9 x 1018 per cu cm for PbTe to -8 x l020 per cu cm for SnTe at 77°K. These carrier concentrations result from deviations from stoichiometry (lead vacancies) in the as-grown crystals. Since lower carrier concentrations are desirable for electrooptic device applications, these crystals are usually subjected to long-term, isothermal anneals.' This paper reports on the growth of Pbl-xSnxTe single crystals from nonstoichiometric melts with the primary objective of producing as-grown material containing relatively low (1016 to 1018 per cu cm) carrier concentrations and also reports on the general characteristics of these crystals. The phase relationships in the Pbl-xSnxTe systems are such that materials solidifying from nonstoichiometric, cation-rich melts will have smaller deviations from stoichiometry than materials grown from stoichiometric melts. Fig. 1 is the T-x phase diagram for PbTe in the vicinity of the stoichiometric composition.3 A crystal grown from a stoichiometric melt will solidify at a melting point maximum at which the solid will contain -0.5002 atom fraction of tellurium. PbTe single crystals grown in our laboratories from stoichiometric melts have carrier concentrations of 9 x 10" per cu cm, indicating that the excess tellurium in the crystals is as expected from this phase diagram. However, growth of PbTe from a lead-rich melt will result in material having a more nearly stoichiometric composition. Although the addition of Sn to the melt shifts the solidus curve further toward the tellurium-rich side,4 the general discussion given for PbTe applies to the Pbl-xSnxTe systems as well. EXPERIMENTAL Single crystals of Pb1-xSnxTe have been grown in our laboratories from nonstoichiometric, cation-rich melts using the Czochralski technique and boric oxide liquid encapsulation. The details of the growth apparatus and growth technique have been reported in a previous paper on growth of these alloys from stoichiometric melts.2 In the present study, three specific crystal compositions were investigated in detail; x = 0.00, 0.10, and 0.17. Growth of alloy crystals from nonstoichiometric melts requires considerable care, and good quality single crystals were obtained in this study only by optimizing the mechanical and thermal stability of the growth system and by using pull rates of from 1 to 3 mm per hr (Pbl-xSnxTe crystals are easily pulled from stoichiometric melts at rates of from 5 to 10 mm per hr). The liquid encapsulation technique was found to yield near-ideal conditions, since the B2O3 layer increased the thermal stability at the growth interface, permitted easy attainment of near-ideal thermal gradients, and dampened vibrations at the melt surface. The hygroscopic character of the B2O3 was a slight problem and vacuum heat treating was necessary to completely remove the water from the boric oxide. During initial growth, the seed diameter was reduced and a narrow neck (1 to 2 mm diam) of several millimeters length was grown. The latter steps were found to be necessary for the growth of single crystals, i.e., if either of these two requirements were

Jan 1, 1970

ENGINEERS AVAILABLE (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members.) Technical graduate, aged-31, with experience as surveyor, chemist with a sulphur company, practical miner, and as chief engineer of an iron mining company, desires a position as mining engineer or superintendent. Speaks French and German. No. 165. Member, aged 31, married, graduate Yale and Massachusetts Institute of Technology, six years' experience in coal and iron mining, from engineer to general superintendent, desires position with large coal or iron company. Will go anywhere. References. . No. 167. Member, technical graduate, with experience as machinist, chemist, construction engineer, and manager-of mines in the United States and Mexico, desires position .as mine superintendent or manager. Speaks Spanish. No. 168. Member, technical graduate, aged 26, with experience as engineer, mine foreman, assistant superintendent for a pyrite mining company. Experience includes diamond drilling, shaft sinking, underground work, milling of pyrites, and mine accounting. No. 169.

Jan 12, 1914

By K. H. Heino

Two 200 T/da Lurgi Turbulent Layer fluid-bed roasters have been in operation at Canadian Electrolytic Zinc Limited since 1966. Zinc concentrate containing 52-54% Zn, 9-11% Fe,31-33% S is treated to produce calcine containing 60-62% Zn,10-12% Fe, .l-.3% S as sulphide and .8-1.2% S as sulphate. Each roaster train comprises a waste heat boiler, two cyclones in parallel and a two-field electrostatic precipitator. Distribution of calcine collected is 10-15 percent from bed overflow, 55-65 percent from boilers, 20-25 percent from cyclones and 2-6 percent from precipitators. A Monsanto designed contact plant produces acid at a rated capacity of 365 T/da (100% H2304 basis) from roaster gases diluted to 7.0-7.5% S02. The process steps are gas cleaning and cooling by weak acid scrubbing, acid mist removal in electrostatic precipitators, gas drying in 93.5-96.5% H2304, conversion of sulphur dioxide to sulphur trioxide in a four-pass converter containing vanadium pentoxide catalyst, and absorption of the sulphur trioxide in 98.1-98.3% H2S04. Product acid is 93.2% H2S04. Conversion efficiency is 97-98 percent and overall sulphur recovery from concentrate is 87-90 percent. The adjacent fertilizer plant has a capacity of 135 T/da of P205. The products are 54 percent phosphoric acid, run-of-pile triple superphosphate, and diammonium phosphate. The plant is of Ugine-Kuhlman design and consists of an air-cooled multiple tank reactor, a tilting pan filter, and a forced circultation vacuum evaporator. Triple superphosphate is made on a continuous belt and partially cured in a rotary dryer. Diammonium phosphate is produced by ammoniating phosphoric acid in a single stage reactor. The slurry of ammonium phosphate is granulated in a blunger and dried.

Jan 1, 1970

By H. H. Richardson, E. H. Dix

Of all the alloying elements used in commercial aluminum alloys, copper stands out as by far the most important, and it is perhaps for this reason that the constitution of the aluminum-copper system has received the attention of a number of experimenters covering a period of approximately 20 years. It would be expected that during this time the equilibrium relations would have been thoroughly and exactly worked out. In a general way this is true, but there is a surprising lack of agreement in the details of the high aluminum end of the diagram, particularly in regard to the solid solubility of copper in aluminum, which has been given variously as 2 per cent. to 5 per cent. at the eutectic temperature. The importance of this is much greater than might at first appear to one unfamiliar with modern commercial aluminum alloys. This is true because, with one exception, the susceptibility of the strong alloys to heat treatment depends, in part at least, upon the solid solubility relations of copper in aluminum. In 1919, Merica, Waltenberg, and Freeman1 published the first detailed information on these solubility relations. They found that the solubility of copper decreases with falling temperature from about 4 per cent. at 525" C. to about 1 per cent. at 300" C. and is apparently still diminishing at lower temperatures. In 1921 there was published a brief account of the results obtained in the National Physical Laboratory, Teddington, England.2 This laboratory, however, reported that 5 per cent. of copper is soluble in aluminum at 540" C., and that this amount decreases to about 3 per cent. at 20" C. In the same year Ohtani and Hemmi3 reported a solubility of 4.8 per cent. copper at 520" C., 2.6 per cent. at 460" C. and 1.5 per cent. at 420" C.

Jan 1, 1926

By A. A. Steel

(Spokane Meeting, September, 1909.) DURING. the summer of 1905 I was employed by the U. S. Geological Survey to investigate the geology, Mining, and preparation of barite in most. of the fields of the United States. The Eastern districts have been more or less completely described ; the Virginia field in detail by Thomas L. Watson, in his paper, Geology of the Virginia Barite-Deposits,' and other fields in abstract., including statistics of production and references to current literature, by various authors .2 There have also been published a few details of the occurrence of barite in the lead-mines of Washington county, Mo.3 The other accounts of this district are erroneous and meager, and since this field is the most important one in the United States at the present time, a detailed description of the local geology seems doubly desirable. Barite-deposits are scattered over nearly the whole of Washington and adjoining counties, but. the product, is all mined from the areas indicated upon the sketch-map, Fig. 1, and is shipped from the stations of the St. Louis, Iron Mountain &. Southern railway, between Blackwell and Potosi, from 45 to 60 miles SW. of St.. Louis. The topography is for the most part gently rolling, with slightly graded streams, usually less than 200 ft. below the higher hill-tops. Along Mineral fork and Indian creek are :some steep bluffs and cliffs, affording good exposures of the

Feb 1, 1910

Extractive Metallurgy Division Institute of Metals Division Iron and Steel Division Council R R McNaughton, Chairman (EMD), Ernest O Kirkendall, Secretary, J H Scaff, (IMD), Morris Cohen, (IMD), T J McLoughlin, (ISD), J S Marsh, (ISD), P T Stroup, (EMD), R D Parks, (MED), D S Eppelsheimer, (MIED) Journal of Metals Editorial Advisory Committee J S Smart, Jr, Chairman, W A Dean, T D Jones, Evan Just, J C Kinnear, Jr, J S Marsh, M Tenenbaum Pacific Northwest Regional Meeting F X Cappa, General Chairman, W W Wiltschko, Chairman (Metals Branch), Program Chairmen H E Lee (EMD), S E Maddigan (IMD), G R Heffernan (ISD), L C Richards (Ind Min Div), James Bell (Finance Committee), Ed Vestica (Registration), Donald Johnson (Special Events)

Jan 1, 1954

By Tasuku Fuwa, John Chipman

Equilibrium data on the reactions of gases with carbon and oxygen dissolved in liquid iron are reviewed and correlated. A source of error in oxygen analysis of graphitic samples is exposed. New experimental data on the oxygen content of high -carbon iron in equilibrium with carbon monoxide indicate that the activity coefficient of oxygen is decreased by additions of carbon. The carbon-oxygen product decreases slightly with increasing carbon content. In recent years a number of investigations have been reported dealing with the equilibria between carbon and oxygen in liquid iron and gases containing carbon oxides. The laboratory study of these reactions dates back to 1931 with the publication of a paper by Vacher and Hamilton' on "The Carbon-Oxygen Equilibrium in Liquid Iron". The principal object of this study was to obtain data on the reaction shown by Eq. [3] below; their data and others by vacherZ permit evaluation of the other equilibrium constants as well. Subsequent studies have been reported by Matoba, Phragmen and Kalling and by Marshall and Chipman.5 The equilibria may be expressed by the following three equations: C + CO,= 2CO;Kl = Pc° [1] 0-+CO = CO,;K2=-P co, "0.PCO c + O = CO; K3 = In the equilibrium constants, ac and a0 are taken as equal to [% C] and [% 0] respectively in the infinitely dilute solution. At finite concentrations an activity coefficient is introduced such that ac =fc [%C], and so forth. It is to be noted that these equations represent only two independent relations, the third being derivable from any two. Richardson and Dennis have determined the conditions of equilibrium in reaction [I] at temperatures of 1560" to 1760°C. Their results have been confirmed by Rist and chipman7 who have shown how the data may be extended to cover the entire range of liquid compositions at temperatures from the eutectic up to 1760°C. An approximate confirmation has been reported by Fuwa and chipman.' These investigations also established the activity coefficient of carbon which was shown to increase rather rapidly with increasing concentration. For the very dilute solutions the value of Kl is expressed in the equation: log^i = - 7280/T+ 6.65 This equation leads to a value of Kl = 430 at 1540° C in excellent agreement with the average value of Marshall and Chipman.5 It is shown as line 1 in Fig. 1 together with the experimental observations. In the case of reaction [2] the direct experimental results can be supplemented by observations on the corresponding reaction with hydrogen, namely reaction [4]:

Jan 1, 1961

By W. C. Ellis, E. S. Greiner, M. E. Fine

C. H. Samans and W. R. Ham (Chicago, Ill., and Dix-field, Maine, respectively)-—For several years we have been studying transitions of this basic type in metals, alloys, glasses, etc. Usually, however, they are not so clearly marked as those which the authors have found, and hence are much more difficult to determine accurately. Since our studies indicate that most of them occur virtually unchanged (as far as temperature is concerned) regardless of the form in which the element appears, we believe that they are a characteristic of the atom. Specifically, we believe that there is an additional rotational degree of freedom possessed by the nucleus which has not been considered heretofore. This nuclear rotation is made up of several components, each related to the several quantum shells of electrons. In chromium there are four of these shells and hence four separate series of characteristic transition temperatures. The lowest temperature at which any transition occurs, based on the present state of our computations, is 125°K, 4° higher than the authors' value of 121°K. A convergence of this series, we believe, shows up at the higher temperature of 2085 °K, surprisingly close to the transformation temperature of 2103°K recently announced by N. J. Grant of M.I.T. for a body-centered to face-centered transformation in chromium. Likewise, our computations indicate a temperature of 311°K for the second transition temperature, reported by the authors as 310 °K. A convergence of this series, we believe, shows up at a higher temperature as the melting point at 2163°K. Although our work on these series must, in a sense, still be regarded as empirical, since we do not understand fully as yet just what the series mean, it is based on a reasonably firm picture. The individual constants, from which the various series are computed for each element, comes directly from the X-ray K absorption limit. Furthermore, the same basic method has accounted for transformation and melting temperatures in about 50 of the chemical elements, which is all we have tried thus far. In many cases the only known transformation is the melting point, but in others the occurrence of transformations or other transitions, equally as well marked as those of the authors, has been pointed out by others. These observations have assisted us greatly. Consequently we were very pleased to see the authors' excellent work in finding these two transitions in chromium. With these confirming data, our picture of this element is clarified considerably, so we expect that at least some of our work can be published in the near future. R. C. Ruder (E. I. du Pont de Nemours & Cu., Wilmington, Del.)—The authors' interpretation of these transitions in terms of 3d to 4s electronic structure transitions is most interesting. It would be interesting to have additional experimental evidence of such transitions from the temperature dependence of the Hall coefficient in the neighborhood of the property changes discussed in this paper. Simple theory15 suggests the Hall coefficient as a measure of the free electron (or s electron) concentration per unit volume. It has been shown that for paramagnetic'" and ferromagnetic1? metals the simple theory is in fact too simple. However, the existence of a discontinuity in the Hall coefficient would provide information which should aid both in our understanding of these transitions and the significance of the Hall coefficient in these metals. It was rather surprising that no significant paramagnetic effects were observed. In this connection the recent work of McGuire and Kriessman18 is cited. They measured the magnetic susceptibility of chromium from 20" to 1460 °C. They also observed no large change in the susceptibility although there might be a change in slope in the vicinity of the 40 °C transition. The existence of these 3d to 4s electronic transitions has been discussed in connection with the paramagnetic susceptibility behavior of nickel and nickel alloys.'"-" Assuming a correspondence principle between classical and quantum mechanical paramagnetic theory and using classical theory to calculate the effective Bohr magneton number from the Curie constant for substances obeying the Curie-Weiss law," it is found that the effective magneton number is a function of temperature. The process of calculation involves the inverse of the differential of the 1/x4 vs. temperature curve so that good and numerous data are necessary to obtain significant results. The data of Fallot23 show a discontinuous increase of about 12 pct in the effective magneton number between 850" and 900 oC, followed by a continuous increase up to the melting point. The data of Sucksmith and Pearce24 show a possible 8 pct increase. The older data of Terry25 and Weiss and Foex26 show a continuous increase. It is possible that small amounts of impurity atoms change these electronic transitions significantly. Fallot's23 data on a nickel alloy with 4.5 atomic pct Fe indicate that the discontinuity occurs around 1300 °C. Systematic investigation of the transition metals for transitions of this nature should provide information which would be very valuable for our understanding of these metals. The absence of antiferromagnetic structures in chromium has been shown by Shull27 using neutron diffraction techniques. M. E. Fine, E. S. Greiner, and W. C. Ellis (authors' reply)—The remarks by Drs. Samans and Ham are certainly very interesting, in particular those pertaining to the close agreement between the theoretically calculated values for transition temperatures in chromium and the experimental values reported by a number of investigators. This is a remarkable achievement and we shall look forward to a more detailed presentation of the method followed in their calculations. We do not believe that the transition in pure chromium near 40 °C remains temperature invariant with alloying, as was reported by Samans and Ham for a number of the substances that they studied. We have not done any work with alloys but base our belief on the results of earlier studies in which less pure chromium was included and considerably lower transition temperatures were observed. The transition tempera-

Jan 1, 1952

By C. K. Gupta, P. K. Jena

Niobium (columbium) metal in the form of a button has been produced by calciothermic reduction of niobium pentoxide using sulfur as the heat booster. In these experiments with 50 g of niobium pentoxide per batch, the influence of percentage of calcium in excess of the stoichiometric, the percentage of sulfur by weight of the niobium oxide, and the outer-wall temperature of the bomb on the quality and yield of the metal has been studied. The maximum yield on this scale was 78 pct using 50 pct excess Ca and 20 pct of S and at a bomb-wall temperature of 600°C. In experiments conducted on 500 g of niobium pentoxide, reduction with 40 pct excess Ca and 20 pct of S, and at a bomb-wall temperature of 500°C, the.yield of the metal improved to 82 to 84 pct. Some of the reduced-metal samples have been electron-beam melted and the button melts thus obtained have been observed to be extremely ductile and capable of cold reduction to 98 pct without intermediate annealing. NIOBIUM, because of its high melting point (2468oC), its ductility, its resistance to corrosion especially in liquid metals, its high-temperature mechanical properties, and its relatively low capture cross section (1.1 barns) for thermal neutrons, has potentialities as a structural material in the field of nuclear engineering. Niobium and its alloys are also gaining importance in high-temperature technology as components in aircrafts, jet engines, and missiles, electronics, chemical engineering, and surgery. In 1904 Weiss and Aichel 1 produced niobium by reduction of its pentoxide by misch-metal. Since then a large number of investigations have been carried out for the extraction of niobium from its compounds. The various routes through which the metal niobium has been extracted from its compounds can broadely be classified into the following groups: a) reduction of its halides, oxides, and fluo-salts with metals like calcium, magnesium, sodium, and aluminum;2-10 b) reduction of its halides with hydrogen and oxides with carbon or carbides;11-18 c) electrolytic winning from its halides and fluo salts;19-25 and d) thermal decomposition and disproportion ion of its halides26-30 Among the processes in commercial use at present are sodium reduction or fused-salt electrolysis of potassium niobium fluoride, carbide or carbon reduction of the oxide, and hydrogen or metallothermic reduction of the chlorides. In 1907 Von Bolton2 prepared niobium by reducing niobium pentoxide with aluminum. Dennis and Adam-sona attempted reducing the oxide with magnesium powder in argon atmosphere and the resulting metal contained as much as 5 pct O. Mondolfo8 claimed a method for the reduction of the oxides with aluminum. In the case of both magnesium and aluminum reduction, it has been stated31 that by-product oxides such as MgO or A12O3 would involve a major separation problem. Further, in the case of alumino-thermic reduction, the solubility of aluminum in niobium and intermetallic formation have to be reckoned with. In 1922 Bridge3 produced niobium by calcium reduction of niobium pentoxide. Dennis and pdamson' obtained the metal by a similar method with an oxygen content of 0.2 pct. In most of the cases of metallothermic reduction of niobium oxides mentioned above, the metal niobium is obtained in the form of powder. In an attempt to produce massive niobium metal, lock' used iodine as the thermal booster in the bomb reduction of niobium pentoxide by calcium. Massive niobium metal was obtained with a maximum yield of 75 pct containing 0.1 pct 0. Joly32 carried out experiments on calcium reduction of niobium pentoxide on a 2-kg scale using sulfur as the heat booster in a sealed bomb filled with argon. In his experiments, the reaction was initiated by passing a current through niobium spiral wire embedded in the charge. In a typical run consisting of 2000 g of niobium pentoxide, 3100 g of calcium, and 800 g of sulfur (S/Nb2O5 = 3.3), he obtained massive metal in the form of a very uneven mass with a yield of -57 pct. With lower amounts of sulfur and calcium, powder niobium mixed with small metal globules was obtained and the yield was also poor. From these experiments he concluded that this method is not a suitable one for industrial development considering the quality and yield of metal obtainable and the possible hazards with higher ratios of sulfur to niobium pentoxide in the -~charere. In the present work, a detailed investigation on the calciothermic reduction of niobium pentoxide in a stainless-steel bomb in presence of sulfur as the heat booster was undertaken on a laboratory scale.

Jan 1, 1964

By G. W. Healy, L. F. Sander

was investigated by reacting thin discs of calcium oxide with gas mixtures of CO2, CO, and Son. Its value was 19,300 * 300 cal independent of temperature in this range. No solid solubility of sulfur in calcium oxide was detected within the limits of the experimental method and it is estimated to be below 0.025 pct by weight. The importance of lime in desulfurization is well-established but complete information on the pure phase equilibrium: CaO + 1/2 s2 = CaS + +02 [11 is not yet available. The goal of this work was to evaluate solid solubility of CaS in CaO and to determine the free-energy change associated with Reaction [I] at temperatures of 1400" to 1650°C. The equilibrium constant for Reaction [1] can be written: It is convenient to rewrite Eq. [2] in the form: where A = {Ps /PqJ1'2 has been referred to' as the "sulfurizing power' of a gas mixture. In this work, thin discs of CaO were suspended in a vertical tube furnace and exposed to CO + CO2 + SOz gas mixtures having known values of A. The samples were then analyzed for sulfur. As expected, X-ray diffraction confirmed that CaS was the only sulfur-bearing phase formed at the relatively low oxygen pressures used. EXPERIMENTAL PROCEDURE Reagent-grade CaCO3 was pressed in a 3/8-in.-diam pill die and prefired in air to produce CaO discs weighing between 0.004 and 0.01 g. Several discs were used to provide a suitable weight for chemical analysis while maintaining a large surface area to react with gas mixtures. These were placed in a platinum mesh basket and suspended in the gas stream in the hot zone of a vertical tube furnace. Desired gas mixtures were prepared from cp grade CO and CO2 and anhydrous grade SO2. The method of soap bubble displacement was used to calibrate capillary flow meters. While this gave excellent results with CO and Con, some problems with bubble insta- bility and soap film "drag" arose with the use of SO2 at low flow rates. Hence, frequent sampling and analysis of gas mixtures was carried out to insure proper control of the ingoing SOZ. The furnace used for gas:solid equilibration was a vertical mullite tube externally wound with 60 pct Pt-40 pct Rh wire having a diameter of 0.028 in. An inner tube of $ in. ID served as the reaction chamber having Pyrex ground joints sealed to the mullite to provide gas-tight connections at top and bottom. A Pt-Pt 10 pct Rh thermocouple was inserted into a protection tube adjacent to the sample basket to measure sample temperature during a run. Constant-temperature control to 2C was observed at any desired set point within the range of this investigation. This was accomplished by a control thermocouple imbedded in the furnace windings which served to actuate an electronic controller wired for high-low operation. The sulfur analyses of the solid samples were carried out using a stoichiometric combustion technique based on the method of Fincham and Richardson. Some analyses were done using a modified evolution method3 but these were used primarily to check the results of the combustion method. The results were in good agreement but the combustion technique of-ferred an advantage in economy of time and material. CALCULATION OF GAS EQUILIBRIA Heating a given mixture of CO + CO + SO2 to high temperatures gives rise to a large number of product species. The details of calculating the partial pressures of these products of interaction and dissociation can be found in several references4,5 and need not be repeated here. The thermodynamic data selected for the major species in the gas mixtures are shown in Table I. Equilibrium constants from these reactions were combined with oxygen, carbon, and sulfur balances and a computer program written to facilitate the calculations. Some early difficulties in reproducing experimental results were finally traced to the effect of atmospheric pressure changes. No reference to consideration of this question had been found in the

Jan 1, 1969

By Samuel L. Hoyt

THIS paper gives a short account of plastic deformation as observed in single crystals of zinc, zinc having been selected for the experiments described herein because the phenomena are comparatively so simple and can be studied throughout such a wide range. It is hoped that the paper will serve to show the type of information which studies of single crystals afford and will contribute toward the solution of the general problem of metallic behavior. PRODUCTION OF ZINC SINGLE CRYSTALS The method of Czochralski,1 as modified by von Gomperz,2 was used to produce the crystals studied. The equipment is shown in Fig. 1. Molten zinc is held in a crucible at a temperature which is not far above its melting point, as measured by a pyrometer. A lava disk floats on ,the melt, and is provided with a central hole about 1 mm. in diameter. A glass tube, drawn into a capillary at the lower end, is suspended from a string which is wound up by an electric drive at the speed desired. At the start, the glass capillary is let down into the melt and the hoist is started.. The capillary brings up a small quantity of molten metal with it to a point just above the lava disk. At this point, a jet of hydrogen cools it and causes it to crystallize, with the result that a small crystal forms. As the hoisting is continued, more molten metal is drawn up, in turn to be solidified by the jet of hydrogen. This additional metal continues the growth of the crystal already formed, and a long, cylindrical crystal results. The speed of hoisting used was generally between 0.1 and 0.5 mm. per sec., and the crystals were from 4 to 6 in. long and about 1 mm. in diameter. By varying the conditions, crystals of quite different orientations were obtained and were used in the study of the phenomena to be described.

Jan 1, 1927

By T. Suganuma

Mitsubishi-Cominco Smelting Co. is a joint venture of Mitsubishi Metal Mining Co. Ltd. (M.M.M.) of Japan and Cominco Ltd. of Canada. The smelter, which is located alongside M.M.M.'s Naoshima copper smelter, was completed in May, 1966 and has a capacity of 36 000 metric tons per year of refined lead. The concentrate feed for the smelter from Pine Point Mines Ltd. is high grade with low impurities; particularly silver, bismuth, antimony, and arsenic, which facilitated a simple plant layout and operation. Concentrate, fluxes, recycle granulated slag and return sinter are drawn from bins by automatic control over weigh belt feeders, sintering is carried out on a 20 m2 Lurgi updraught sintering machine, furnacing in a 3.0 m x 1 ½ m water jacketed blast furnace equipped with an Asarco continuous tapper, refining in four 120 metric ton kettles and casting on a 25 metric ton/hour automatic casting machine. The S@ gas from sintering is cleaned in a high temperature baghouse utilizing glass bags and is then delivered to the M.M.M. copper smelter acid plants. The furnace gases after cleaning in a low temperature baghouse are vented to atmosphere.

Jan 1, 1970

By J. Bruce Wagner, Roger L. Levin

Integrated forms of two solutions of Fick's second law for the movement of a plane interface through a sample of wustite, and for diffusion into a semi-infinite slab of wustite, are shown to yield nearly identical values of the chemical diffusion coeffcients of cation vacancies in wustite, over the temperature range 900° to 1100°C. The chemical diffusion coefficients, the values of D obtained for the propagation of a concentration gradient through samples of undoped and doped wustite, are obtained from the equations It is becoming increasingly important in metallurgical practices to understand the role of the chemical diffusion coefficient, i.e., the diffusion coefficient of a species across a concentration gradient. During the first stages of sintering, one of the mechanisms by which the bonds between neighboring particles develop is by volume or bulk diffusion. This diffusion coefficient as deter- where ?m is the weight change at any time t, ?W is the total weight change at t =8, A is the area of the specimen, and AC is the total change in the cation concentration after the establishment of equilibrium, as determined by reduction experiments in different carbon monoxide -carbon dioxide mixtures within the limits of existence of the single-phase field. mined from the standard equations for volume diffusion during sintering is actually a chemical diffusion coefficient, and it has been observed to be many times larger than the self-diffusion coefficient as determined on the same materials by experiments using radioactive tracer techniques. Kuczyn-ski1 has noted that, if the controlling mechanism of sintering of A12O3 in an oxidizing atmosphere is the diffusion of oxygen, then this diffusion coefficient as measured from sintering rates is about 2.2 x 104 higher than the self-diffusion measurements obtained by tracer techniques. He has also reported the diffusion coefficient obtained from the rate of sintering of Fe2O3 powder to be about 10 6 times faster than the self-diffusion coefficient of

Jan 1, 1965

By Ervin E. Underwood

IT has been recognized for many years that dis-persed particles have great value in raising the creep resistance of metallic alloys. In fact, some of the most successful high-temperature alloys owe their superiority to this factor above all others. A recent observation by Glen1," indicates that even better high-temperature resistance to deformation results in alloys capable of two successive precipitation reactions. The ramifications of this finding are of great interest. Unfortunately, our understanding of the reasons for such notable improvements has not kept pace with technical developments. In an effort to uncover some of the basic facts governing strengthening by particles, a program was initiated at the Battelle Memorial Institute with the primary goal of comparing creep strengths in single-phase and two-phase (precipitating) alloys. The effects of precipitation from solid solution on the creep properties of alloys are generally such that the resistance to creep is increased. However, if alloys are heat treated to different degrees of hardness before creep testing, it is often found that those possessing the maximum hardness initially do not necessarily have the maximum creep resistance. Depending on the stresses and temperatures involved other structures may prove more desirable. Considerations of the above nature indicate the importance of defining the initial state of the alloy. Here, it was decided to start with quenched single- phase alloys in which precipitation and creep deformation proceed concurrently. Equipment and Experimental Procedures Preparation of the Specimens—Four 25 lb ingots were prepared from 99.999 pct Cu and 99.996 pct Al to compositions of 1, 2, 3, and 4 wt pct Cu. Spec-trographic and chemical analyses are listed in Table I. After heat treatments and intermediate reductions, the alloys were cold rolled to 1/8 in. thick sheet. The final cold reductions amounted to 50, 40, 20, and 10 pct for the 1, 2, 3, and 4 pct Cu alloys, respectively. The specimens for creep testing were machined into tensile flats 7 in. long, 3/4 in. wide (at the shoulders), and 1/8 in. thick. The reduced sections were 1/4 in. wide and 21/2 in. long. After heat treatments at 540°C to an ASTM grain size of 1 1, the specimens were quenched into water at room temperature, then electropolished in a glacial acetic acid and perchloric acid solution. The gage marks were Knoop impressions placed 2 in. apart on the reduced sections. Blanks of 1 x 1 in, were cut from the same sheets for the age hardening runs and were given the same grain size heat treatments. The specimens and blanks were stored in a refrigerator at —40°C until needed for testing. Creep Measurements—Creep tests were conducted in a constant temperature room which was maintained at 26° ±1°C. A split-type, hinged, vertical-tube furnace was mounted on a horizontal track so that the specimen could be enclosed suddenly. Thus, it took about 15 min for the specimen to come within 5°C of the test temperature. The temperature variation along the specimen was controlled to about

Jan 1, 1958

By Bruce W. Gonser, A. U. Seybolt

A few copper-zinc-hasp alloys mppt die-casting requirements reasonably well, although improvements are desired. Aluminum bronzes, high-tin bronzes and some copper-nickel-zinc alloys can be die-cast, according to Herb,' but seldom are because of such factors as higher melting ranges and greater cost than certain of the brasses. Fox2 has summarized the copper-base die-casting alloys that were in commercial use in 1937 and has given the effects of different alloying constituents. Table 1 gives some of the properties of these alloys as reported by Fox. a Properties reported by Fox.2 b Trade name of Brastil, Doehler Die Casting Co., similar to Webert Alloy,34 American Brass Co., and Tombasil Alloy,5 Ajax Metal Co. e Trade name Tinicosil, Titan Metal Manufacturing Co. Melting point (liquidus) of the yellow brass is given by Herb1 as 1650" F., of the high-silicon Brastil (with 4.5 to 5 per cent Si) as 1600" F., and of the nickel silver as 1675" F. d Criterion not stated.

Jan 1, 1940

By A. U. Seybolt, Bruce W. Gonser

A few copper-zinc-hasp alloys mppt die-casting requirements reasonably well, although improvements are desired. Aluminum bronzes, high-tin bronzes and some copper-nickel-zinc alloys can be die-cast, according to Herb,' but seldom are because of such factors as higher melting ranges and greater cost than certain of the brasses. Fox2 has summarized the copper-base die-casting alloys that were in commercial use in 1937 and has given the effects of different alloying constituents. Table 1 gives some of the properties of these alloys as reported by Fox. a Properties reported by Fox.2 b Trade name of Brastil, Doehler Die Casting Co., similar to Webert Alloy,34 American Brass Co., and Tombasil Alloy,5 Ajax Metal Co. e Trade name Tinicosil, Titan Metal Manufacturing Co. Melting point (liquidus) of the yellow brass is given by Herb1 as 1650" F., of the high-silicon Brastil (with 4.5 to 5 per cent Si) as 1600" F., and of the nickel silver as 1675" F. d Criterion not stated.

Jan 1, 1940

By E. S. Machlin

THE function of this paper is to present certain results based on the fact that the strain energy arising from the solution of out-of-size solute atoms into the solid matrix is free energy and not internal energy, and that this strain energy is almost wholly shear strain energy as Zener1 pointed out. One natural consequence of this fact is an expression for the excess entropy of mixing due to the strain energy. Also, a derivation of the integral molar free energy of mixing partitioned to strain energy will be made using the model of Lawson2 and thermodynamics. This derivation has the advantage of showing in a simple way the assumptions involved in Lawson's treatment. The excess entropy of mixing partitioned to strain energy can be derived in two ways. The first way makes use of the fact that the strain energy is almost wholly in the form of shear strain energy. In this case, as Zener1 pointed out, the change in entropy due to the addition of shear strain energy is to a first approximation given by ?S/?? p,T = - ?lnµ/?T p,? Hence, the excess entropy of mixing partitioned to strain energy will be given by Sx ? = ?S/?? p,T Gx ? = - ?lnµ/?T p,? Gx ? where, Gx ? is the relative integral molar free en- ergy partitioned to strain energy; S is the entropy; is the shear strain energy; µ is the shear modulus; T is the absolute temperature; p is the pressure; and ? is the shear strain. Zener,1 as well as others, has pointed out that the shear strain energy stored in a compressible isotropic solid due to the insertion of an off-size incompres-sible sphere into a spherical hole in the solid, is approximately given by 2/3 µ/O (O°I - O)2 where a is the volume of spherical hole and no , is the volume of sphere. If we now consider the introduction of one mol of such spheres into an infinite volume of solid, then the relative partial molar free energy excess due to strain energy alone is GM ? = 2/3 µ/v (v ° 1 - v)2 where v is the molar volume of solvent and v°1, is the molar volume of pure solute type 1. Let us consider that these spheres are the two types of atoms in a binary solution, then there will be a similar relation for solute 2. The total relative integral molar free energy excess due to strain is then, to the approximations stated above GM ? = GM ? x1 + GM2 ? x2 = 2/3 µ/v [(v ° 1 - v)2 x1 + (v ° 1 - v)2 x2]. Lawson's relation for the strain energy can be de-

Jan 1, 1955

By George M. Fowler, J. P. LYDEN

T HE relationship of geological structure to orebodies and to the great masses of chert in the Tri-State mining district is of such significance that it prompts a brief recital of the existing information regarding the various periods of structural deformation. We began to note a relationship between structure and orebodies early in our studies of the field, and further work revealed a like relationship of structure to the great masses of chert so commonly associated with the ore-

Jan 1, 1934

By H. C. Chao, L. H. Van Vlack

Small MnS inclusions with known crystallographic orientations were placed inside powder compacts of low-carbon steel. After the metal was axially campressed with negligible end friction, the deformstions for the metal and the inclusions were compared. The MnS inclusions deformed more when the [100] direction was aligned with the compression axis than when the [111] direction was parallel to this axis. The deformations of the inclusions in the two principal radial directions were equal for each of the above orientations. Inclusions with [110] compression alignments did not deform with radial symmetry. The relative deformation of the inclusion and metal was closely dependent upon the relatiue hardness of the two phases. The relative deformation of the two phases was not sensitive to the rate of deformation. RECENT studies by the authors1.&apos; suggested that the plastic deformation of MnS in steel would probably be highly sensitive to the orientation of the inclusions and to the temperature of the metal. This paper reports an investigation of these factors upon MnS behavior within steel. Manganese sulfide (MnS) possesses an NaCl-type structure and typically has extensive (l10) {110} slip as a separate (noninclusion) crystal.&apos; A secondary slip system, ( l 10) { l l l}, has also been observed where the major slip system is restricted. In general, MnS inclusions must be rated as a highly deformable second phase.3 The amount of sulfide deformation varies, however, with several composition and processing factors. Some of these have been only partially assigned. For example, it is known that minor amounts (<0.01 pct) of silicon within free-machining steels will increase the amount of MnS deformation,4 but the mechanism of the added deformation can only be surmised at the present. Manganese sulfide and steel have sufficiently comparable deformation characteristics so that slip which is started in steel may be continued through the sulfide inclusions and back into the steel if the crystal orientations are favorable.5 A more detailed discussion of previous work on the plastic deformation of NaC1-type crystals and on the plastic deformation of inclusions within a metal is given in Chao&apos;s work.6 EXPERIMENTAL PROCEDURE The manganese sulfide which was used in this study was prepared by previously described methods.&apos; Single crystals of MnS, both as cleavage cubes and as spheres, were oriented within steel powder compacts so that the desired crystal directions were parallel to the direction of axial compression. A four-stage hydrostatic compaction procedure was used and involved the following steps. In the first stage part of the powder was placed in a metal die 1 in. in diameter with a thick (1 in. OD, 5/8 in. ID) rubber liner which had one end plugged. The steel powder was hand-rammed, making it as dense as possible before placing a carefully sized MnS crystal (either as a sphere or as a cube) near the center. The crystal was oriented with the chosen direction vertical; viz., [001], [011], or [111], with the aid of a X10 microscope. A pair of tungsten wire threads 0.020 in. in diameter was inserted along the side of this (&apos;core compact" to locate the desired plane after the compression tests. After the crystal was positioned in the center of the die, more powder was added and carefully rammed by hand. The die was then capped with a rubber plug of the same hardness and thickness as that of the liner. The whole assembly as shown in Fig. 1 was compacted by a ram load of 54,000 lb (about 70,000 psi). In the second stage a smaller, 3/4-in, rubber-lined die was used to give a stress of approximately 120,000 psi. The above process was repeated with the initial compact serving as a core for a larger compact. The final product after sintering was a cylinder 1 cm long and 1 cm in diameter, having a density of 7.54 g per cu cm. This was close to the theoretical density since the metal contained a non-metallic phase. There was no evidence of MnS deformation during the hydrostatic compaction or subsequent sintering. Elevated-temperature hardness data were obtained by procedures previously described.2 Compression tests for inclusion deformation utilized the cylinders which were described above. The critical problem in these tests was the lubri-

Jan 1, 1965

By J. A. Botin, K. H. Singh

INTRODUCTION The Alfredo underground mine is one of the three mining operations of Rio Tinto Minera, S.A., all near the community of Rio Tinto in Huelva province of southwest Spain. The other two operations are Corta Atalaya open pit (Pyrite ore) and Cerro Colorado open pit (Copper ore 1. Underground mining of Alfredo Mine for pyrites started in the nineteenth century and continued without interruption until 1979 when it was discontinued due to economical reasons. In 1972, a new project was started for the mining of copper bearing ores on the footwall of the pyrite deposit. This copper ore is locally named “Cloritas” and it forms a nearly vertical and tabular shaped orebody which forms an envelope at the footwall of the San Dionisio pyrite orebody. Mining of the Cloritas commenced in 1975 using cut and fill stoping. In 1977, the original project was completely revised which led to the introduction of a bulk mining system to achieve a planned production of 3,000 tonnes of ore per day. This paper covers the economic and planning aspects of the mine and discusses the evolution of the mining method for the Cloritas orebody. A GENERAL DESCRIPTION OF THE CLORITAS OREBODY The “Masa San Dionisio” (figure 1 ) is a massive sulphide orebody located in the town of Rio Tinto, about 90 kilometres west of Sevilla, Spain. Extensive vein-type sulphide mineralization exists in the volcanic host rocks of the Masa San Dionisio. Within this area of stockwork veins, there is a higher concentration of copper in the form of chalcopyrite in a zone adjacent to and paralleling the contact with the massive sulphides. This copper envelope is locally referred to as the "Cloritas Orebody” and the ore within it is called "Cloritas”. The main zone of the Cloritas orebody, (figure 11, is tabular and nearly vertical having a length of 375-400 m east-west, a thickness of 20-50 m north-south, and a vertical extension of 500 m from the surface. In addition to this area, there is a second less important low grade area called zone 2A located to the north of the main zone below 26 Level which, in some sections, is not fully separated from the main zone. MINING METHODS Mining in Rio Tinto area can be traced back to the Phoenecians and the Romans. Modern day mining started with the demand for sulphuric acid during the last half of the nineteenth century. By 1971, more than 33 million tonnes of pyrite had been mined out of Alfredo Mine, (San Dionisio Orebody), using labor intensive drift and fill methods and also by open pit method. During the last decade, underground mining of the pyrite had become uneconomic due to lower prices and a slackening demand for pyrite, and the underground mining operations for pyrite were finally stopped in 1979. In 1971, a major change in the long range mining plans for Masa San Dionisio was established. Between 1971 and 1975, underground mining of pyrites was progressively reduced while open pit extraction was increased in

Jan 1, 1981