Search Documents

By D. H. Desy, L. C. Fincher

The magnesium-rich end of the Mg-Ti phase diagram was investigated. The liquidus, solidus, and solvus boundaries to 1 pct Ti were established. All alloys were prepared by saturating molten magnesium with titanium in a consumable titanium crucible under inert gas maintained at 230 psig. The liquidus of the Mg- Ti system was determined by analysis of dip samples taken from 700° to 1300°C under equilibrium conditions in a pressurized inert atmosphere furnace and by analysis of small ingots rapidly poured and quenched from 1400° to 1500°C. The solubility of titanium in magnesium ranged from 0.018 wt pet Ti at 700°C (0.012 wt pet at 650°C by extrapolation) to 1.035 wt pet Ti at 1500°C. The solidus for compositions ranging from 0.03 to 1.00 wt pet Ti was determined to be 650° ± 1°C by thermal analysis. The titanium solid solubility values ranged from 0.08 wt pet at 350°C to 0.19 wt pet by extrapolation to 650°C. The freezing reaction is peritectic. No intermetallic compounds were found in the system; the phase in equilibrium with molten magnesium saturated with titanium was found to be titanium with magnesium in solid solution. Solid titanium will dissolve at least 1.32 wt pct Mg. PREVIOUS investigations of the Mg-Ti system have shown considerable disagreement on the solubility of titanium in liquid magnesium. Furthermore, the solid solubility of titanium in magnesium has not been well established. Liquidus curves for previous work and for the present investigation are shown in Fig. 1. Aust and Pidgeon1 used a dip-sampling method on molten magnesium held in equilibrium with solid titanium under a protective atmosphere to determine the solubility and found that it ranged from 0.0025 wt pet Ti at 651°C to 0.015 wt pet Ti at 850°C. Eisenreich2 introduced titanium into molten magnesium by means of TiCL4 adsorbed on BaCl2. Ingots were then cast at various temperatures. Making the assumption that only the titanium dissolved in magnesium at the time of casting was soluble in H2SO4, Eisenreich determined the solubility of titanium in molten magnesium to range from 0.003 wt pet at 655°C to 0.115 wt pet at 800°C. Eisenreich also determined the solid solubility of titanium in magnesium to be 0.015 wt pet at room temperature and 0.045 wt pet at 500°C. Since the solid solubility just below the freezing temperature for the bulk of the alloy was much larger than the liquid solubility just above the freezing temperature, Eisenreich concluded that the freezing reaction was peritectic. Obinata et al.3 equilibrated molten magnesium with titanium in hermetically sealed titanium containers which were then furnace-cooled. The titanium content of the magnesium was then determined and found to range from 0.170 wt pet at 700°C to 0.85 wt pet at 1200°C. No intermetallic compound was found in the system. The Armour Research Foundation4 determined two points on the solvus by electrical resistivity methods: 0.00057 wt pet at 200°C and 0.0008 wt pet at 300°C. At higher temperatures, data were meaningless with no trends observable. The authors of this report believed that the lack of significant data at the higher temperatures was due to variations in specimen geometry, although there was no positive evidence to verify this supposition. The present investigation was undertaken to clarify the uncertainty in both the liquidus and solvus of the magnesium-rich end of the Mg-Ti system. EQUIPMENT AND MATERIALS The equipment used in this investigation, with some modifications, was essentially that used by Crosby and Fowler5 in their determination of part of the Mg-Zr phase diagram. The equipment, as modified for this work, is shown in Fig. 2. It consists of a sealed furnace chamber which can be pressurized with inert gas so that melts can be made above the boiling point of magnesium at atmospheric pressure. Melts are made by induction heating in a titanium crucible which, after diffusion of sufficient magnesium into the walls of the crucible to saturate the titanium at the sampling temperature, comprises the solid phase in equilibrium with the molten magnesium. Dip samples may be taken with the sampling tube, or the entire furnace may be tilted so that ingots may be poured into a mold in the side chamber. The principal difference from the earlier apparatus is in the thermocouple, which in the present equipment is enclosed in a protection tube and immersed directly in the melt. The tips of both the thermocouple protection tube and the sampling tube, which dip into the melt, are made of high-purity titanium. The 4 1/2-in.-long titanium tip of the sampling tube is threaded into a steel tube, O in Fig. 2, which extends through the top of the furnace. To determine whether the temperature at the tip of

Jan 1, 1969

By J. A. Bailey, J. H. Tundermann

The dihedral angles of the solid-liquid interfaces were measured at various temperatures above the solidus and the interfacial energies calculated when small additions of copper, indium, lithium, magnesium, antimony, and silicon were made to an aluminum alloy containing 3 pct Sn. When the results were compared with those of the Al-Sn alloy some differences were found which could be interpreted in terms of the ability of the added element to enter into solution or form intermetallic compounds with the aluminum and tin. It was shown that in some cases considerable changes in the shape of intergvanular liquid films can be brought about by comparatively small compositional changes in the alloy. DURING the melting or solidification of an alloy a temperature range is usually found where the presence of a liquid phase may be detected at the grain boundaries of a solid. It is believed that the presence of this liquid phase is responsible for hot tearing in castings and welds and hot shortness in the working of some alloys at elevated temperatures. Rosenberg, Flemings, and Taylor1 in a study of the solidification of aluminum castings have indicated the importance of intergranular liquid films and shown that their shape and distribution at the end of solidification effect the hot tearing characteristics of the material. The shape of such intergranular liquid films are determined largely by the ratio between the solid-liquid interfacial energy (yLS) and the grain boundary energy (ySS). A measure of this ratio (yLS/ySS , relative interfacial energy) is the dihedral angle 8. The dihedral angle 0 is related to the relative interfacial energy by the following expression: Rogerson and Borland 2 have also suggested that the shape of the intergranular liquid is an important factor in determining the susceptibility of a material to hot shortness. They showed that on a comparative basis materials having the lowest dihedral angles at a given temperature gave the greatest severity of cracking. They stated that liquid in the form of globules should be less harmful than liquid in the form of extensive films as more intergranular cohesion should be possible. Rogerson and Borlland 2 also showed that the susceptibility of an A1-Sn alloy to hot cracking can be reduced by small additions of cad- mium. It was found that the cadmium gave an increase in the dihedral angle at all temperatures. Ikeuye and smith3 investigated changes in the dihedral angle and relative interfacial energy with temperature for a number of ternary alloys formed when small additions of bismuth, cadmium, copper, lead, and zinc were made to an A1-Sn alloy. They found that in most instances changes in the dihedral angle were caused by compositional changes in the liquid phase; as the composition of the liquid approached that of the solid the dihedral angle decreased. They noted that the addition of a third element which was soluble in both the liquid and solid phases at a given temperature may decrease the dihedral angle (e.g., the addition of copper or zinc) but otherwise the ternary alloys formed exhibited dihedral angles between those of the A1-Sn binary alloy and those of the binary alloy of aluminum with the added element. Dwarakadasa and Krishnan4 investigated the changes in dihedral angle and relative interfacial energy with temperature when small additions of magnesium, iron, silicon, manganese, sulfur, cobalt, and silver were made to a copper alloy containing 3 pct Bi. They found that in all cases the added elements gave an increase in the dihedral angle and relative interfacial energy when compared with the values obtained for the simple binary alloy at the same temperature. It was noted that an increase in temperature gave a decrease in dihedral angle and relative interfacial energy in each of the ternary alloys studied. Similar results have been obtained by Ramachandran and Krishnan5 for the addition of small quantities of lead. This paper describes the application of dihedral angle measurement to the determination of the shapes of liquid phases at various temperatures above the solidus when small additions of copper, indium, magnesium, lithium, antimony, and silicon are made to an aluminum alloy containing nominally 3 pct Sn. An attempt is made to correlate the measurements with the relative solubility of the added elements in tin and aluminum. The work was undertaken to provide more data concerning the effects of temperature and composition on the shape of liquid films above the solidus. EXPERIMENTAL PROCEDURE In the present work ternary aluminum alloys containing nominally 3 pct Sn and small additions of high-purity copper, indium, lithium, magnesium, antimony, and silicon were made. The alloys were melted in a graphite crucible under an inert atmosphere of argon and cast into ingots 6 in. long by 0.5 in. diam. The ingots were then cut into rods 1.5 in. long, given a 50 pct cold reduction, and machined into test pieces 0.5 in. long by 0.5 in, diam for heat treatment. The alloy samples were annealed at the various test temperatures between the liquidus and solidus for approxi-

Jan 1, 1967

By G. H. Miller

With the recent advances which have been made in science and technology and the increased use of mathematics in this area, the question of the best mathematics courses for a mining engineer to take is of major importance. The question becomes even more difficult to answer due to the recent increase in the number of different mathematics courses in the last two decades offered by the mathematics departments. Therefore, the National Study of Mathematics Requirements for Scientists and Engineers (NSMRSE) was designed to provide some answers to these questions. Approximately 10,000 scientists and engineers were selected for the Study, These individuals were placed in two categories: (1) The Awards Group, recipients of national honors or awards and those recommended by the members of the Board of Advisors as having national and international reputations in their areas of specialization and (2) The Abstracts Group, persons exceptionally productive in their research, based on the number of journal articles listed in the last five years in the Engineering Index, Scientific and Technological Aerospace Reports, Chemical Abstracts, Biological Abstracts, and the Physics Abstracts. The NSMRSE Course Recommendation Form and the Instruction and Course Content Sheet were constructed with the aid of the Board of Advisors and other consultants. For the Study, 40 courses were selected by the mathematical consultants. In order to make sure that the basic content of the mathematics courses was the same for all respondents, a brief resume of each of the 40 courses was given. The NSMRSE Course Recommendation Form consisted of seven sections. These sections were as follows: Section 1, 38 different specializations; Section 2, orientation of work (applied through theoretical); Section 3, highest degree obtained; Section 4, place of employment (academic, nonacademic); Section 5, administrative capacity (administrative or nonadministrative); Section 6, age groups (five-year intervals). Section 7 contained the 40 courses which were to be marked according to five categories: (1) Course Length, 3 to 36 weeks; (2) Applied-Theoretical Orientation, a five-point scale; (3) Course Level, freshman through graduate; (4) Knowledge of Course; and (5) Use of Course Content in Work. The Analysis The report of the data is based on the replies received from 44 mining engineers. This group was part of the Awards and Abstracts Group for all engineers. The resume of the recommended courses is reported in quintiles (upper fifth to lower fifth), since recommendations of this kind are not precise. The results of the Study are based on recommendations of the most active research men in engineering in the U.S. today; therefore, the reader should realize that these course recommendations represent an upper bound of mathematics requirements for the Ph.D. in both undergraduate and graduate work. Conclusions and Recommendations 1) Mining engineering students who plan to be active research specialists should take all those courses which are "very highly recommended" (80-10070) and "highly recommended" (60-79.9%). Those courses in the upper two quintiles and recommended by most mining engineers are: first-year calculus, third-semester calculus, elementary differential equations, applied statistics, and machine computation. Courses of "moderate recommendation" (40-59.9%) are: vectors, intermediate ordinary differential equations, the first course in partial differential equations, elementary probability, and linear programming. 2) The great majority of mining engineers indicated that they prefer a course which is concerned primarily with applications. Only the standard courses such as first-year college mathematics, calculus, differential equations, and advanced calculus received a recommendation for 50% theory and 50% practice. Therefore, all mathematics courses given to mining engineers should contain many applications and little theory. Engineers in both the applied and the combination (ap-plied-theoretical) groups indicated a definite need for applications in all courses. 3) In general, recommendations were for mathematics courses to be given for short intervals of time such as 3, 6, or 12 weeks. Only the standard courses mentioned previously received the usual one-semester or one-year recommendation. Therefore, it is of value to combine several related courses into a one or two-semester course so that the mining engineering student could acquire important mathematical knowledge at an early date in order to prepare him for his research. 4) There was little use for the newer courses in modern mathematics such as the functional analysis sequence, the modern algebra sequence, and the group theory sequence. In addition, there were uniformly very low recommendations (0-19.9%) for multilinear algebra, complex variables, mathematical logic, special functions, integral equations, approximation theory, analytic mechanics, integral transforms, and geometric algebra. Therefore, these courses should be given a low priority. 5a) Comparisons among mining engineers with different backgrounds showed that the combination ap-plied-theoretical group recommended more mathematics than the applied group. 5b) There was little difference in recommendations between the administrative group and the nonadminis-trative group. 5c) Analysis of age groups showed that those in the lower age groups gave significantly higher recommendations to courses such as the first course in partial dif-

Jan 1, 1971

By A. F. Henderson, C. F. Cornell, A. F. Dunyon, D. A. Dahlstrom

Ossi E. Palasvirta (Development Engineer, Oliver Iron Mining Diu., U. S. Steel Gorp.)—The authors are to be congratulated for their interesting article, which thoroughly illustrates the variables inherent in filtration of taconite concentrate. The work and the conclusions based thereon largely parallel the test work done by the writer at the Pilotac plant" and the experience gained with a commercial size agitating disk filter in the same plant. At Pilotac, however, a thorough study was also made of the effect of depolarizing (demagnetizing) the filter feed, and it is the purpose of this discussion to comment on the merits of depolarization of the magnetite concentrate prior to filtering. The work at Pilotac was done in three phases: 1) preliminary laboratory testing with a circular filter leaf of 0.047 sq ft, followed by 2) plant testing using a 4-ft diam, single-disk agitating filter that was purchased on the basis of the pilot tests on the 4-ft model. In the laboratory tests depolarization was achieved by slowly withdrawing' batches of thickened concentrate from a coil producing an alternating field of about 300 oersteds. In plant tests the standard Pilotac procedure' was employed, wherein the pulp falls freely through the depolarizing coil. The preliminary tests in the laboratory at first seemed to indicate that although depolarization of the filter feed decreases the cake moisture, it also tends to decrease the thickness of the cake, thus decreasing filtering rate. The tests with the 4-ft disk filter soon showed, however, that the compactness of the cake, attained during the form period because of depolarization, permitted a considerable decrease in drying time without any sacrifice in final moisture content. Thus, the filter could be operated at a much higher speed, and the overall capacity was higher than with magnetized feed. Because of the great compactness of the cake there was little shrinkage during the drying period, which prevented cracking and subsequent loss in vacuum. This in turn permitted operation with as thick a feed pulp as the diaphragm pumps could handle, eliminating the necessity of pulp density control. On the basis of these findings, the 6-ft agitating disk filter has been operated at 2 rpm, using feed pulps varying from 65 to 73 pct solids. Initially Saran 601 was used as medium, but it was later replaced with a relatively open, tight-twist nylon cloth. Filtering rates up to 750 lb per ft- er hr can be attained with feeds averaging about 70 pct- 270 mesh, and there is no trouble because of cracking. The cake moistures vary between 8.5 and 9.5 pct. To recapitulate, the merits of depolarizing the filter feed may be summed up as follows: 1) The well dispersed pulp shows less tendency to settle in the filter tank. 2) The homogeneous filter pool results in more even cake formation. 3) Because of absence of flocs, great compactness of cake is attained during the form period. 4) The cake does not tend to crack during the drying period. 5) A drier cake is produced. 6) A shorter drying period is necessary, permitting higher operating speed, which in turn results in increased capacity. 7) Density of the feed pulp can be kept as high as the equipment can handle. This increases capacity, since it is directly proportional to the percentage of solids in the pool. A few tests were also made to study the effect of chemical flocculants on filtration efficiency. Results showed that the effects of chemical and magnetic floc-culation were quite similar. Thus the use of a floccu-lant would impair rather than improve the filtering of magnetite concentrate. A. F. Henderson, C. F. Cornell, A. F. Dunyon and D. A. Dahlstrom (authors' reply)—We want to thank O. E. Palasvirta for his comments, particularly in view of the encouraging results obtained with demagnetized taconite concentrate. In our studies an attempt was made to evaluate the effects of depolarizing the feed to the plant filters by passing the slurry through a coil, similar to the method described by Palasvirta. Unfortunately, in our experiments there were no startling improvements in performance level, neither cake rate increase nor cake moisture reduction. However, when slow filter cycle speeds were employed, the filter cake tended to crack and the vacuum level dropped, resulting in an increase in cake moisture content. When demagnetized feed was used during slow speeds, no cake cracking was evidenced and the vacuum level remained constant. Thus the depolarizing coil was found necessary only in cases of cracking. It should be noted that most of our test work concerned a feed of 85 to 90 pct —335 mesh and about 60 pct by weight solids concentration. This contrasts with 70 pct —270 mesh and 65 to 73 pct by weight solids as noted by Palasvirta. Reviewing both sets of results, it might be concluded that depolarizing may be successfully employed to alleviate cake cracking tendencies and may markedly improve cake rates and moistures on the coarser taconite concentrates. Further investigations may disclose the exact relationship of grind and pulp density to the depolarizing action.

Jan 1, 1959

By J. W. Spretnak, J. N. Cordea

The gain boundary relaxation in high-purity aluminum, nickel, copper, and silver was studied by means of a low-frequency torsion pendulum. Both internal friction and creep at constant stress tests were conducted. A lognormal distribution in relaxation times was found to account for the relatively wide experimental internal friction peaks and the gradual relaxation behavior during the creep tests. This distribution was separated further into a lognormal distribution of relaxation time constants and a normal distribution in activation energies. A spread of up to ±6 kcal per mole in the activation energies accounted for the major part of the distribution. A "double-peak" internal friction phenomenon was observed in silver. The activation energies in kcal per mole derived from the grain boundary relaxation phenomena are 34.5 for aluminum, 73.5 for nickel, 31.5 for copper, and 41.5 for silver. It was found that the rain boundary relaxation strength in these metals increases with the reported stacking-fault energy. GRAIN boundary relaxation phenomena have been observed in a large number of polycrystalline metals and alloys. Numerous investigations have been conducted to study the structure of the grain boundary through this relaxation process. One of the first investigators was Ke1-4 who observed that the activation energy for grain boundary relaxation in aluminum, a brass, and a iron was about the same as that for volume diffusion. He concluded that the grain boundary behaved as if it were a thin liquid layer with neighboring grains sliding over one another. Leak5 conducted experiments on iron of a higher purity and observed that the grain boundary activation energy is comparable with that of grain boundary diffusion. He suggested that, in metals where this relationship holds, the damping may be caused by a reversible migration of grain boundaries into adjoining grains. Nowick6 has presented an interesting view of inter-facial relaxation with his "sphere of relaxation" model. A relaxed interface is represented as one where the shear stress is greater than the normal value along the edges and zero in the interior of the interface. The region of the stress relaxation is pictured as a sphere surrounding the interface. From his calculations Nowick concluded that the slip along an interface is directly proportional to its length. Therefore, the time of relaxation, T, depends on the size of the relaxation interface. This means that in the Arrhenius relationship, t = TO exp[H/RT], valid for atom movements, the relaxation time T is predicted to be proportional to the grain diameter through the pre-exponential term, TO. Since the internal friction can be given as Q-1 = ?j wt/(1 + w2r2), where ?J is the relaxation strength and w is the angular frequency, an increase in grain size at a constant frequency will shift the peak to a higher temperature. A great deal of work has been done to determine the exact relationship between the internal friction and grain size.1,5,7,8 In metals, the grain boundary peaks are found to be lower and broader than predicted theoretically.' The above model can explain this by a distribution in the size of the interface areas, represented by a distribution in the parameter tO, and an overlap of spheres of relaxation, represented by a distribution in activation energies. Both these phenomena result in an over-all distribution in the relaxation time, which could affect the internal friction peak height, breadth, and also position. This relationship between the experimental data and theoretical calculations appears very promising in the study of interfacial relaxation mechanisms. THEORY A lognormal distribution in t can sometimes be used to adequately describe the spectrum of relaxation times governing an anelastic relaxation. wiechert9 originally suggested such a distribution to explain the elastic after-effect in solids. This choice is particularly applicable to grain boundary relaxation when considering Saltykov's work.'' He found a lognormal distribution in the grain sizes within a metal. Recently Nowick and Berry11 have introduced a log-normal distribution in T into the theoretical internal friction equations. The form of the distribution function is where z = In(r/rm), and Tm is the mean value of t. The parameter ß is a measure of the distribution and is the half-width of the distribution when is l/e of its maximum, IC/(O). Nowick and Berry have described the methods to obtain the parameters Tm, ß, and ?,J from experimental internal friction and creep test data. In the idealized case, where only one relaxation event occurs with one relaxation time, only ?J and T are necessary to completely describe the event, and 0 = 0. For the broader internal friction curves 6 is some positive number greater than zero. The larger the 6, the greater is the half-width of the distribution in In t.

Jan 1, 1967

By G. L. Hassler, E. Bruner

An apparatus and method is described whereby the relation between saturation and capillary pressure under decreasing saturation can be quickly determined for small core samples. The initially saturated core is cen-trifuged at increasing rates and the average saturation is measured at each rate with the aid of a stroboscope device. A theory and calculation procedure is given whereby the accelerations and saturation values can be converted into a true curve of capillary pressure versus saturation. The present work differs from previously described use of the centrifuge to obtain capillary-pressure curves of core samples3 in that the core is centrifuged alone, so that the whole range of saturations required by the properties of the sample and the radially varying centrifugal force occurs within the sample. The calculation procedure nevertheless secures correct results from simply obtained values of the average saturation. The apparatus described was developed in connection with studies of capillary pressure and wetting of oil-field rocks, and the paper provides the apparatus background for a previous publication' dealing more fully with the uses and implications of the data in petroleum engineering. The method is applicable, however, to general combinations of immiscible fluids and porous or comminuted solids, and may be useful in other fields. Introduction The importance of capillary phenomena in determining the behavior of liquids in porous media has long been recognized. The concept of capillary Pressure was early formulated, and in recent Years discussions of the application of the laws of capillarity to oil field problems have appeared.l-3 One reason why progress in the application of capillary phenomena to the solution of problems of reservoir mechanics has not been more rapid has been the lack of a, satisfactory technique for measuring the capillary pressures in reservoir rocks. It is the principal purpose of this paper to describe a method by which the relation between capillary pressure and saturation can be determined for small consolidated core samples which have been extracted and resaturated, Capillary Diaphragm Perhaps the most direct way to measure the capillary pressure in a rock is to make piezometric contact with the wetting liquid through a diaphragm of porous material with high displacement pressure saturated with the liquid in question.3-6 The liquid in the diaphragm assumes the pressure of the liquid in the core, which can then be measured with a manometer, while the atmospheric air is prevented by capillarity from entering the diaphragm and affecting the pressure measurements as long as the displacement pressure of the diaphragm is not exceeded. With an apparatus of the type illustrated schematically in Fig. I, the relation between capillary pressure and saturation can be measured for a small core sample by starting with the core saturated 100 per cent, applyillg successively greater suctions

Jan 1, 1945

By R. W. Cahn, C. D. Graham

Two predictions of the oriented growth theory of recrystallization textures have been tested by measuring the orientation dependence of the rate of growth of a single grain into a strained single crystal of aluminum, and determining the orientations of artificially and spontaneously nucleated grains growing preferentially into strained aluminum single crystals. Growth rates are found to be insensitive to orientation, except that new grains with orientations similar to the matrix or to a twin of the matrix have very low mobilities. Similarly, new grains growing preferentially into a strained crystal have random orientations, except that orientations near that of the matrix or its twins are avoided. The predictions of oriented growth theory are thus not confirmed. BASICALLY, the oriented growth theory of re-crystallization textures1 rests on the assumption that the rate of growth of a recrystallizing grain depends strongly on the orientation of the growing grain relative to the strained matrix into which it grows. In particular, the theory holds that in face-centered-cubic metals the orientation which corresponds to maximum growth rate is one in which the growing grain and the matrix are related by a rotation about a common <111> direction. The amount of rotation, as derived from several kinds of experiments,2-1 has been assigned various values, generally in the range between 20" and 40". (A <111> rotation of 60" is a twin relationship.) The conclusion that boundary migration rates depend strongly on orientation is based almost entirely on indirect evidence; there have been very few direct measurements of boundary migration rates as a function of orientation.* " The present investigation was undertaken to provide such measurements, to help make possible a decision between the oriented growth and oriented nilcleation theories of recrystal-lization textures. The basic experimental program consisted of measuring the rate of growth of a single recrystal-lizing grain consuming a strained single crystal, with the orientations of both grains preselected so that the effect of orientation on growth rate could be determined. A prerequisite for such an experiment is a strained single crystal which will support the growth of a new grain but which will not spontaneously nucleate new grains on heating. That is, the crystal must support the growth of a grain nucleated artificially, but contain no recrystalliza-tion nuclei which will become active at the testing temperature. Beck was apparently the first to note that such a condition could exist," and to make use of the condition for am experiment of the type described here.&apos; The present work was actually suggested, however, by a report of Tiedema". " that an aluminum single crystal strip, oriented with a (111) plane in the plane of the strip and a < 112> direction parallel to the tensile axis, would not recrystallize after 20 pet extension even when heated almost to the melting point, provided that the strip was heavily etched before being heated. This result could not be duplicated in the present work. In fact, it was found that any crystal which deformed in multiple slip (<100>, <112> and <111> orientations) underwent spontaneous nucleation after 15 pet extension, even if etched. However, crystals which deformed in single slip, and which did not develop heavy deformation bands, could be extended 15 pet without showing spontaneous nucleation at temperatures up to 600°C. Crystals oriented within about 10o of <110> which developed heavy deformation bands could be extended 10 pet without showing spontaneous nucleation. In all cases a heavy etch was required to prevent nucleation. Etching was necessary because of the presence of an oxide layer on the crystal surface at the time of straining, which leads to preferential nucleation at the surface.&apos;&apos; Grain Growth Rates Experimental Procedure and Results—Aluminum strips of 99.6 pet purity (principal impurities 0.19 pet Fe and 0.12 pet Si), 1 mm by 1 cm in cross section, were grown into single crystals of controlled orientation by the strain-anneal method of Fuji-wara.&apos;"&apos; " A sharp temperature gradient was maintained in the strips during growth by lowering them into a salt bath controlled at 650°C. Crystal orientations were determined by the etch-pit method of Barrett and Levenson" to an accuracy of ±2O. The crystals were extended by 10 or 15 pet in a simple hand operated tensile machine. Crystal orientations were rechecked after extension, and were found to be in agreement with the orientations predicted by the formula of Schmid and Boas." After extension, the grip ends of the single crystal specimen were cut off with a jeweller&apos;s saw, and the crystal heavily etched (at least 20 pet wt loss) in hot 10 pet Na or KOH solution. A region of severe local deformation was then introduced at one corner of the strip, usually by cutting off the corner with shears. Heating this end of the strip caused a large number of new grains to nucleate at the sheared edge. One of these grains grew to occupy the full width of the strip. The appearance of the strip at

Jan 1, 1957

By Richard Hodgson

FMC Corporation, at their mine and soda ash refinery near Green River, Wyoming, currently mines in excess of 3 million tons per year of trona. Upon completion of the current expansion, the mine will be producing in excess of 4.0 million tons per year. The single level mine, approximately 1,500 feet in depth, is currently serviced by five (5) concrete lined circular shafts varying in diameter from 12 ft. to 24 ft. A sixth shaft is complete, but not yet operational and the seventh is currently being sunk. Two of the shafts are equipped with single drum hoists. The original production shaft is equipped with a double drum hoist. The newest production shaft and the main service shaft are both equipped with ground mounted friction hoists. These friction hoists have given excellent service and another will soon be installed as a man and material hoist at No. 7 Shaft. There are a number of advantages that the ground mounted hoist has over a tower mounted hoist. There are also operating problems common to both. FMC&apos;s original experience with ground mounted friction hoists began in 1962 with the conversion of a single drum hoist to a friction hoist. The converted hoist was an Ottumwa with a 5 ft. diameter drum and a 4 ft. face. This hoist had been installed at the No. 3 Shaft for some years prior to its conversion to a friction hoist. At the time the conversion of this hoist was made, there were no friction hoists in service in Wyoming. Wyoming mining laws required that all conveyances carrying men be equipped with safety dogs. Since it was desired that wire rope guides be used, safety dogs were impractical. Agreement was reached with the State Mine Inspectors that safety dogs would not be necessary provided that recommended rope safety factors for hoisting men would still be maintained if one hoisting rope was broken. Since-the shaft is approximately 1,500 ft. deep, the recommended safety factor is 6.0 so that this installation has a safety factor in excess of 8.0 for hoisting men when new ropes have been installed. The hoist conversion was engineered by Lake Shore, Incorporated. The friction ring was made in halves and bolted over the original drum face which had been machined to remove the grooves. The ring provided for four 3/4 in. diameter ropes on 8 inch center to center spacing. The pitch diameter of the modified drum was 72 inches. The grove liners are hald in place by hard-wood wedges bolted to the drum. The other modification required by the conversion was an increase in size of bearing caps and the hold-down bolts because of the increased force tending to lift the drum.

Jan 1, 1975

By Che-Yu Li, J. L. Gregg, W. F. Brehm

Oriented, oxygen-doped niobium bicrystals were tested in liquid lithium. The grain boundaries were attacked preferentially. The depth of the penetrated zone varies as (time)2. The penetration was aniso-tropic, had a high activation energy, and increased with the increased oxygen doping level. A possible model was proposed to account for the experimental observations. 1 HE grain boundary penetration of a metallic system by liquid metal has been studied by several investigators. Their results are summarized by Bishop.&apos; Most of these works show that the penetration by liquid metal corresponds to the phenomenon of liquid metal wetting. In the case of a grain boundary, wetting will occur when twice the solid-liquid interfacial tension is smaller than the grain boundary tension resulting in the replacement of the grain boundary by two new solid-liquid interfaces. Other possibilities exist; for example, the atoms of the liquid metal may diffuse into the grain boundary region due to chemical potential gradient. The gradient can be produced by impurity segregation or simply be due to the increase in solubility in the grain boundary region. The penetrated grain boundary in these cases may remain solid at the test temperature. The Nb-Li system has been of considerable interest because of its possible technological applications. For fundamental interest it provides a possibility of studying the grain boundary penetration process which is not controlled by the wetting mechanism. The pure niobium is not attacked by the liquid lithium, but if niobium containing more than 300 to 500 ppm oxygen by weight is exposed to liquid lithium, corrosion occurs at the solid-liquid interface and preferentially at grain boundaries. Previous investigators2-&apos; have proposed that this preferential corrosion at grain boundaries is caused by oxygen segregation there, with subsequent inward diffusion of lithium to form a Li-Nb-0 compound. These investigators also found that the corrosion could be retarded by adding 1 pct Zr to the niobium to precipitate the oxygen as ZrO2 upon proper heat treatment. However, there are no quantitative data on the kinetics of the grain boundary penetration process to test the validity of the proposed corrosion mechanism. In this work an investigation of this penetration process in oriented bicrystals was made as a function of the oxygen doping level in the bulk niobium and the grain boundary orientation. A possible model for the penetration process based on the experimental results was proposed. EXPERIMENTS Oriented niobium bicrystals were grown by arc-zone melting oriented single-crystal seeds.7 These bicrystals contained simple tilt boundary. The [001] directions in the two grains were tilted about a common [110]. The bicrystals were 31/2 in. long and 5 by 4 in. in cross section with the straight, symmetric, planar grain boundary longitudinally bisecting the crystal rod. The bicrystals were doped with oxygen by anodically depositing a layer of Nb2O on the surface in a 70 pct HNO solution at 100 v, using a stainless-steel cathode. The specimens were homogenized by annealing in evacuated quartz tubes at 127 5°C. Oxygen content of the niobium was measured from microhardness values, after DiStefano and Litmman.&apos; Supplementary checks were made with vacuum-fusion analysis.7 Individual test specimens cut from the doped bi-crystal rods, about by by % in. in size, were tested inside double jacket sealed capsules. The inner jacket was niobium, the outer was stainless steel. The niobium inner jacket eliminated the problem of dissimilar-metal mass transfer.&apos; The lithium (99.8 pct pure, obtained from Lithium Corp. of America) was handled only in a purified argon atmosphere in a Blickman stainless-steel glove box. After introduction of lithium, the capsules were sealed by welding. Further detailed experimental procedures are given in Ref. 7. The capsules were heat-treated in vertical Marshall resistance furnaces. Temperatures were controlled to When heating above 1100°C, it was necessary to seal the furnace work tube and flow argon through to prevent failure of the stainless-steel outer jacket of the capsule. Tests were made on 6" 2", 16" 2, and 33" i2" bicrystals at oxygen levels up to 2600 ppm by weight in the 6&apos; and 16" crystals and with 1300 ppm oxygen in the 33&apos; crystals. The oxygen levels were controlled to 100 ppm. Most of the quantitative data were obtained from 16" bicrystals between 800" and 1050°C. The capsules were quenched into water after the test and cut open with a water-cooled abrasive wheel. The capsules were then submerged in water, which dissolved the lithium and freed the specimen. Measurement of the depth of the penetrated zone in the grain boundary was done either on metallographically prepared surfaces or directly on the grain boundary plane after the specimen was fractured in tension in the grain boundary plane. The depth of penetration measured by both methods agreed well. Further details describing these techniques have been reported elsewhere.&apos;p7

Jan 1, 1969

By W. A. Mudge

This discussion will be limited to malleable, commercially pure nickel and some high-nickel alloys, containing more than 50 per cent of nickel, which are produced by The International Nickel Company, Inc. at its Huntington works, West Virginia, from electrolytic nickel or from a nickel-copper sulphide matte. The principal sources of nickel are sulphides of nickel, copper and iron, which are found in the large deposit of pyrrhotite-pentlandite-chalcopyrite ores in the Sudbury area of Ontario, Canada. Pentlandite, a complex nickel-iron sulphide, is the nickel carrier. These ores are concentrated, roasted, and smelted to remove considerable iron and sulphur and to produce a nickel-copper sulphide matte. Separation of the component sulphides of this matte, followed by electrolytic refining, results in the production of electrolytic nickel and electrolytic copper; direct refining of a selected portion of the matte gives the nickel-copper alloy, Monel. FUNDAMENTAL OPERATIONS Melting of the metallic materials is done in natural gas-fired, acid furnaces of the open-hearth, or reverberatory, type, having capacities of 6 to 20 tons; in three-phase, basic, electric-arc furnaces, having capacities of 7 to 20 tons; and in basic, high-frequency induction furnaces having capacities of ½ to 3 tons. Malleable, commercially pure nickel is melted in the acid open-hearth furnace. The charge is sulphur-free, electrolytic nickel, containing 99.9 per cent nickel* and clean mill scrap. Monel, containing approximately two thirds nickel and one third copper, is produced by roasting the nickel-copper sulphide matte to an oxide, smelting the oxide with charcoal in a 20-ton, acid open-hearth furnace, adding clean mill scrap, duplexing to a 20-ton, basic, electric-arc furnace, and refining in this furnace with a lime-fluorspar, carbide slag. Inconel, containing nickel, 80 per cent; chromium, 14 and iron, 6, is melted in the 7-ton electric-arc furnace or the 3-ton induction furnace. The charge is electrolytic nickel, ferrochromium and clean mill scrap. These are the fundamental operations. High-nickel alloys are produced from one of these three materials by additions of suitable amounts of manganese, aluminum, silicon or copper. For example, the age-hardenable alloy, K Monel, is produced from Monel by the addition of approximately 3 per cent of aluminum, and D nickel is produced from nickel by the addition of approximately 4.5 per cent of metallic manganese. For conversion to rods, bars, sheet, strip, tubing and wire forms, by hot-working and cold-working operations, the molten materials are teemed into ingots ranging in size from 14 by 14 by 60 in., 3300 lb., to 36 by 36 by 48 in., 18,000 lb. All ingots are overhauled mechanically before hot working.

Jan 1, 1946

By J. W. Taylor, E. G. Zukas

THE results of shock-loading studies on copper were reported several years ago by smith. In his experiments, Smith found that there was a correlation between the shock direction and the orientation of twins which the shock produced. By using free-surface-type shots in which the free surface of the specimen was not normal to the shock direction, he showed conclusively that twinning of copper in impulsive loading was caused by the rarefaction wave. Similar tests with iron, however, showed that it twinned during compression. More recent studies of iron2 and on Fe-Si single crystals3 have shown that twinning can be suppressed in these materials by shock loading at pressures high enough so that the velocity of the shock wave exceeds the elastic-wave velocity. From these observations, it appeared that twinning was caused by the shear stresses present in the zone undergoing adjustment from one-dimensional to three-dimensional loading. At high pressures, such a zone becomes so thin that there is insufficient time for the relatively ordered motion of atoms involved in twinning to occur. Twinning in copper, therefore, cannot be produced by a single compressive shock wave because resolved shear stress large enough to create twins exists only for a very short time (0.01 psec or less) before the pressure increases suddenly and loading becomes essentially hydrostatic. (A typical pressure vs time record for a copper shot, illustrating the short rise time of the compression wave, is shown in Fig. 1.) If, on the other hand, a second shock wave can be created in a precompressed sample, then the new elastic limit is several kilobars,4 and a resolved shear stress sufficient to cause twinning should be maintained for an adequate time period (0.1 psec or more). This experimental situation can, in fact, be realized. The experimental arrangement used to do so is shown in Fig. 2. By utilizing the pressure transformation in Fe-V alloys, it was possible to shock-load the copper in compression while the copper was already precompressed. In the first test, an 8 wt pct V-Fe sample was used as a driver for loading the copper, and the copper was exposed to the following series of compressive shocks: 1) an elastic wave of about 8 kbars, which is usually ignored in shock studies; 2) the pressure transformation wave for the driver of 200 kbars; and 3) the driving shock wave of 270 kbars pressure. Metallurgical determination of the angular twin distribution, shown in Fig. 3, with respect to the shock direction and the shock rarefaction direction (which was 23 deg from the shock direction) showed that twinning took place

Jan 1, 1965

By Fred B. Brost

In 1976, a decision was made to install a conveying system to transport ore 10.3 km (6.4 miles) from the new Eisenhower mine to Twin Buttes. The system, supplied and installed by Cable Belt Ltd., of England, represents a radical departure from conventional conveyor systems. The driving tension is applied through two endless wire ropes while the belt acts only as the carrying medium. Features of the system are a single 2240-kW (3000-hp) drive and a 60° angle bend. Construction was completed in two years and full production was attained alter several mouths operation.

Jan 12, 1979

By William E. Ford, Edward Salisbury Dana

1. Normal Class (28) Gypsum Type 2. Hemimorphic Class (29) Tartaric Acid Type 3. Clinohedral Class (30) Clinohedrite Type Mathematical Relations of the Monoclinic System Crystallographic Axes. - The monoetinic system includes all the forms which are referred to three unequal axes, having one of their axial inclinations oblique. The axes are designated as follows : the inclined or clino-axis is a; the ortho-axis is b, the vertical axis is c. The acute angle between the axes a and c is represented by the letter 0; the angles between a and b and b and c are right angles. See Fig. 331.

Jan 1, 1922

By Louis Stott

IT is well known that the oxide of beryllium was identified as a new "earth" in 17971 and the metal first isolated in 18272. The history of the many difficulties encountered by early investigators, the laboratory achievements of Lebeau3, Fichter4 and Oesterheld5, and the eventual development of methods for commercial production are well covered in the literature, particularly in the authoritative published work of Siemens and Halske6 reviewing their comprehensive investigation of the element. Accordingly it has seemed desirable to restrict this paper to the properties and uses of beryllium and its alloys.

Jan 1, 1936

By M. A. Bryant, J. C. Goodwin, T. B. Faddies, L. D. Kornze

The Mercur Gold Mine is located 56 km (35 air miles) southwest of Salt Lake City in north central Utah; In July 1981 Getty Mining Company made the decision to put Mercur into production. The first gold bar was poured in April 1983. This paper provides details on: 1) the history of the camp, 2) past production, 3) geology of the deposit, 4) the exploration and development program, 5) ore reserve estimates, 6) detailed geologic pit mapping, 7) production blasthole sampling techniques and 8) the use of geostatistics (kriging) in handling assays and gold extractions to produce the required mill feed.

Jan 1, 1985

By R. P. Carreker, R. L. Fullman, J. C. Fisher

THE existence of the phase TiAg has not been reported previously. Other investigators have denied the existence of compounds in the Ti-Ag system.13&apos; However, phases of equi-atomic proportion have been reported by Raub, et al.&apos; in the (similar) systems of titanium with gold and copper and zir- conium with silver. Raub&apos;s work indicated that titanium and silver are immiscible in the liquid state. No evidence of this was found although a very wide melting range exists which makes the preparation of homogeneous alloys difficult. TiAg is apparently formed by a peritectic reaction between /3

Jan 1, 1954

By R. J. De Angelis, J. B. Cohen, A. Nelson

In this note several recent results on twinning in copper shock-loaded with planar shock waves will be presented and the role of the twins in recrystalliza-tion will be discussed. The twinlike markings first observed in shock-loaded copper by smith1 were identified as twins by De Angelis and Cohen.2 This identification has been confirmed by others.3 In Ref. 2 it was also shown that there is an orientation dependence for twinning at low shock pressures, such that twins in a crystal loaded in [lll] form in the rarefaction or tensile wave but in

Jan 1, 1967

By P. A. Laxen, H. R. Spedden

WHEN a mineral particle is fractured, bonds between the atoms are broken. The unsatisfied forces that appear at the newly formed surface are considered to be responsible for the adsorption of ions at the mineral surface. A knowledge of the mechanism and extent of ion sorption from solution onto a mineral surface is of interest in the development of the theory of flotation.&apos;*&apos; Study of the adsorption of sodium from an aqueous solution oftheon quartz offers a simple approach to this complicated problem. The availability of a radioisotope as a tracer element meant that accurate data could be obtained."." Three main factors which appeared likely to affect the adsorption of sodium are: l—concentration of sodium in the solution, 2—concentration of onotherof cations in the solution, and 3—anions present in the solution. Hydrogen and hydroxyl ions are always present in an aqueous solution. By controlling the pH, the concentration of these two ions was kept constant. The variation in thesethe amount of sodium adsorbed with variation in sodium concentration was then determined under conditions standardized in regard to hydrogen ion. The effect of concentration of hydrogen ions and of other cations was also measured. A few experiments were made to get a preliminary idea on the effect of anions. The active isotope of sodium was available as sodium nitrate. Standard sodium nitrate solutions were used throughout these experiments except when the effects of other anions were studied. It was found that sodium adsorption increased with sodium-ion concentration, but less rapidly than in proportion to it. Increasing hydrogen-ion concentration, or conversely decreasing hydroxyl-ion, brings about a comparatively slight decrease in sodium-ion adsorption. Increasing the concentration of cations other than hydrogen or sodium decreases somewhat the adsorption of sodium ion. It would appear as if the kind of anion is a secondary factor in guiding the amount of sodium ion that is adsorbed. Materials and Methods Quartz The quartz was prepared as in previous work in the Robert H. Richards Mineral Engineering Laboratory&apos; except for the refinement of using de-ionized distilled water for the final washing of the sized quartz, prior to drying." To minimize the laborious preparation of quartz, experiments were made to determine .whether the sodium-covered quartz could be washed free of sodium and re-used. The experiments were successful as indicated by lack of Na" activity on the repurified material and by its characteristic sodium adsorption. Table I gives the spectrographic analyses of the quartz used. The quartz ranged from 16 to 40 microns in size, averaging about 23 microns (microscope measurement), and had a surface of 1850 sq cm per g (lot I), 2210 (lot 11) and 2000 (lot 111) as determined by the Bloecher method." Radioactive Sodium Method of Beta Counting for Adsorbed Sodium: Na22, the radioisotope of sodium, possesses convenient properties.&apos; It has a half-life of 3 years, thus requiring no allowance for decay during an experiment. On decay it emits a 0.575 mev ß+ radiation and a 1.30 mev r radiation. The decay scheme is illustrated in the following equation: ß+ NaR-------&apos;8&apos;77NeZ2 3 years The /3 radiation is sufficiently strong to penetrate an end-window type of Geiger-Mueller counting tube. This, in turn, makes it possible to use external counting, a great advantage in technique. Furthermore, it permits the assaying of solids arranged in infinite thickness, while assaying evaporated liquors on standardized planchets. The equipment used was standard and similar to that employed by Chang.R The original active material was 1 ml of solution containing 1 millicurie of Na" as nitrate. This active solution was diluted to 1000 ml. Five milliliters of this diluted active solution was found to give a quartz sample a sufficiently high activity for accurate evaluation of the sodium partition in the adsorption measurements. Also, 1 ml of final solution gave a sufficiently high count for precision on the liquor analyses. The sodium concentration of the diluted active solution was 1.2 mg per liter, so that 6 mg of sodium for 60 ml of test solution and 12 g of quartz was the minimum amount used. The active solution was stored in a Saftepak bottle. Procedure for Adsorption Tests: The method consisted of agitating 12 g of quartz with 60 ml of solution of known sodium concentration for enough time to establish equilibrium between the solution and the quartz surface. The quartz was separated as completely as possible from the solution by filtering and centrifuging. The activity on the quartz and in the equilibrium solution was measured and the partition of the sodium was calculated from the resulting data. The detailed procedure for the adsorption test is set forth in a thesis by Laxen." In brief, it included the following steps: 1—Ascertainment of linearity between concentration of Na" and activity measured. 2—Evaluation of factor to translate activity on solid of infinite thickness in terms of activity on an evaporated active film of minute thickness, on the various shelves of the counter shield. 3—Taking precautions to avoid evaporation of water during centrifuging

Jan 1, 1953

By P. A. Laxen, H. R. Spedden

WHEN a mineral particle is fractured, bonds between the atoms are broken. The unsatisfied forces that appear at the newly formed surface are considered to be responsible for the adsorption of ions at the mineral surface. A knowledge of the mechanism and extent of ion sorption from solution onto a mineral surface is of interest in the development of the theory of flotation.&apos;*&apos; Study of the adsorption of sodium from an aqueous solution oftheon quartz offers a simple approach to this complicated problem. The availability of a radioisotope as a tracer element meant that accurate data could be obtained."." Three main factors which appeared likely to affect the adsorption of sodium are: l—concentration of sodium in the solution, 2—concentration of onotherof cations in the solution, and 3—anions present in the solution. Hydrogen and hydroxyl ions are always present in an aqueous solution. By controlling the pH, the concentration of these two ions was kept constant. The variation in thesethe amount of sodium adsorbed with variation in sodium concentration was then determined under conditions standardized in regard to hydrogen ion. The effect of concentration of hydrogen ions and of other cations was also measured. A few experiments were made to get a preliminary idea on the effect of anions. The active isotope of sodium was available as sodium nitrate. Standard sodium nitrate solutions were used throughout these experiments except when the effects of other anions were studied. It was found that sodium adsorption increased with sodium-ion concentration, but less rapidly than in proportion to it. Increasing hydrogen-ion concentration, or conversely decreasing hydroxyl-ion, brings about a comparatively slight decrease in sodium-ion adsorption. Increasing the concentration of cations other than hydrogen or sodium decreases somewhat the adsorption of sodium ion. It would appear as if the kind of anion is a secondary factor in guiding the amount of sodium ion that is adsorbed. Materials and Methods Quartz The quartz was prepared as in previous work in the Robert H. Richards Mineral Engineering Laboratory&apos; except for the refinement of using de-ionized distilled water for the final washing of the sized quartz, prior to drying." To minimize the laborious preparation of quartz, experiments were made to determine .whether the sodium-covered quartz could be washed free of sodium and re-used. The experiments were successful as indicated by lack of Na" activity on the repurified material and by its characteristic sodium adsorption. Table I gives the spectrographic analyses of the quartz used. The quartz ranged from 16 to 40 microns in size, averaging about 23 microns (microscope measurement), and had a surface of 1850 sq cm per g (lot I), 2210 (lot 11) and 2000 (lot 111) as determined by the Bloecher method." Radioactive Sodium Method of Beta Counting for Adsorbed Sodium: Na22, the radioisotope of sodium, possesses convenient properties.&apos; It has a half-life of 3 years, thus requiring no allowance for decay during an experiment. On decay it emits a 0.575 mev ß+ radiation and a 1.30 mev r radiation. The decay scheme is illustrated in the following equation: ß+ NaR-------&apos;8&apos;77NeZ2 3 years The /3 radiation is sufficiently strong to penetrate an end-window type of Geiger-Mueller counting tube. This, in turn, makes it possible to use external counting, a great advantage in technique. Furthermore, it permits the assaying of solids arranged in infinite thickness, while assaying evaporated liquors on standardized planchets. The equipment used was standard and similar to that employed by Chang.R The original active material was 1 ml of solution containing 1 millicurie of Na" as nitrate. This active solution was diluted to 1000 ml. Five milliliters of this diluted active solution was found to give a quartz sample a sufficiently high activity for accurate evaluation of the sodium partition in the adsorption measurements. Also, 1 ml of final solution gave a sufficiently high count for precision on the liquor analyses. The sodium concentration of the diluted active solution was 1.2 mg per liter, so that 6 mg of sodium for 60 ml of test solution and 12 g of quartz was the minimum amount used. The active solution was stored in a Saftepak bottle. Procedure for Adsorption Tests: The method consisted of agitating 12 g of quartz with 60 ml of solution of known sodium concentration for enough time to establish equilibrium between the solution and the quartz surface. The quartz was separated as completely as possible from the solution by filtering and centrifuging. The activity on the quartz and in the equilibrium solution was measured and the partition of the sodium was calculated from the resulting data. The detailed procedure for the adsorption test is set forth in a thesis by Laxen." In brief, it included the following steps: 1—Ascertainment of linearity between concentration of Na" and activity measured. 2—Evaluation of factor to translate activity on solid of infinite thickness in terms of activity on an evaporated active film of minute thickness, on the various shelves of the counter shield. 3—Taking precautions to avoid evaporation of water during centrifuging

Jan 1, 1953

By Frank L. Nason

RECENT explorations with a diamond-drill, originated and conducted by Mr. J. A. Van Mater, Superintendent of the Lehigh Zinc and Iron Company, have revealed some very important geological facts, which, it is believed, will be of special practical interest to mining engineers. During these explorations the writer was frequently called in consultation, and hence the facts here recorded are almost entirely the results of personal observation. The franklinite-deposit upon which the explorations were conducted has a long continuous outcrop. Figs. 1, 2 and 3 give a map and sections. Beginning at the extreme southern point,

Jan 1, 1895