Search Documents

By I. Cornet

INTRODUCTION WITH the greatly expanding use of magnesium during the war, it appeared necessary to the War Metallurgy Committee that the notch sensitivity of magnesium alloy extrusions be further investigated and the influence of various factors upon notch sensitivity be noted. Accordingly, the National Defense Research Committee of the Office of Scientific Research and Development placed a research contract with the University of California, supervised by the War Metallurgy Committee. The work discussed herein was done under "Restricted" Project NRC-21, reported in Dec. 1943 1; it has been released for publication by the O.S.R.D. SCOPE OF THE INVESTIGATION The notch sensitivity of various magnesium alloy extrusions was determined under axial tension, and also under several conditions of nonaxial tension. Hardness, grain size and other metallographic features were observed; stress-strain data were obtained, and the chemical compositions of the alloys were determined, in order to correlate these quantities with the notch sensitivity. Notch sensitivity under axial tensile load was determined for a few specimens which had been cold worked to various degrees by tensile prestraining. Magnesium alloy extrusions studied included Dowmetal 0, X, J, and M. For comparison, extrusions of aluminum alloy 24S-T, cast bars of aluminum alloy I22-T2, and cast bars of magnesium alloy C were also tested, The specified chemical composition of these alloys is given in Table I. All bars tested were within specification limits of composition. Investigation of the tensile notch sensitivity of various magnesium alloy extrusions, under conditions of axial and eccentric load, showed little or no correlation with stress-strain or other conventional data. Since the many uncontrolled variables present might mask significant relationships, one alloy was selected for intensive study. Magnesium 0 alloy extrusions were subjected to experimental heat treatments, and the changing hardness, tensile strength, microstructure, and notch sensitivity observed. EXPERIMENTAL TECHNIQUES AND PROCEDURES Tensile Testing Bars used for axial loading were machined with 3/8 in.- and with 1/4-in. minimum diam, and included specimens with 6o° V notches (Fig I and 2). Each V-notched specimen was roughed out carefully and then finished with a honed tool. These V-notched bars were sampled frequently, sectioned, polished, and examined at 500 X magnification to control

Jan 1, 1948

By S. F., French

IN reviewing the design of the ore haulage system for the Morenci project, the reader should bear in mind that the railroad and its equpiment cannot be considered as an independent railroad provided only for the purpose of transporting ore from one point to another, but as an integral part of the operation which begins at the electric shovels loading ore at the mine, and ends where the ore, after having been crushed in the primary crushing plant, is deposited in the bins at the secondary crushing plant. Obviously then, the problem consisted of designing a system that would function to the best possible advantage in complete co-ordination with the other units.

Jan 1, 1942

By M. C. Fuerstenau, A. M. Gaudin

A homogeneous suspension is viewed by X-rays. The radiation density seen, affords a measure of the extra absorption due to the solids contained. This radiation density, at a predetermined depth, varies with time. The chart of this relationship gives the desired determination. s it is frequently necessary to know the distribu-rt tion of particle sizes in various products used in industrial applications, a number of means have been devised for these determinations. Some of them include direct microscopic measurement, screening of product, extraction of samples from a settling slurry, air and liquid elutriation, adsorption of gases and liquids, and light absorption. The absorption of light as a means for particle size analysis has been known and employed for some time. X-ray absorption has not received the attention that light has enjoyed primarily because of the complex and costly instrumentation involved with X-rays. In 1954, Brown and Skrebowskil suggested the use of X-rays for this type of determination but did not supplement their suggestion with experiment. In 1958, the authors conducted size analysis experiments on suspensions of quartz with the Trans-viewer: an X-ray unit specifically adapted for sedimentation research, and Rossa conducted experiments in a similar manner in 1959 with a stable gamma emitter, AmZ4l, on suspensions of uranium oxide. To illustrate the applicability of X-ray absorption for analyzing particle size distributions, an essentially mono-energetic and well collimated X-ray beam was used as a source. The beam was made mono-energetic by placing a zirconium filter before the counting window together with feeding the pulses from the proportional counter into a reverter, a device capable of discriminating against pulses of various heights. The sketch in Fig. 1 shows the collimation arrangement in more detail. As shown, the X-ray beam was collimated by inserting a 3/8-in. ID pipe into one of the ports of the X-ray tube and further by two small steel plates with slits 3/32-in. wide and 1/2-in. long placed in front of the window of the Geiger-Mueller (G-M) tube. One of the plates was located 1/2 in. and the other 2 1/2 in. from the window of the counter; both plates were contained in an aluminum holder mounted on the box containing the G-M tube. This type and degree of collimation should eliminate any intensity due to scattered radiation; the transmitted intensity would then be solely a functior. of the absorption by the suspension at that level. Experimentally, homogeneous suspensions of finely ground quartz were prepared, Daxad (a sulfo-nated compound made from wood) was added as dis-persant, and the transmitted X-ray intensity measured as a function of time at a fixed depth in the suspension. In more detail, the experimental procedure involved the following: 1) measuring the transmitted X-ray intensity through the Daxad solution at a predetermined position or settling depth in the absence of solids, 2) placing a known amount of dry solids into the vessel and agitating thoroughly, 3) measuring the transmitted X-ray intensity at time zero (i.e., immediately upon cessation of stirring), and 4) measuring the transmitted X-ray intensity as a function of time (a 10-sec counting interval being chosen and counting being started 5 sec before the desired time). Since a linear relationship exists between percentage solid in a slurry and the logarithm of transmitted intensity for a homogeneous material, the cumu-

Jan 1, 1961

By Nestor Torres-Acuña, Fathi Habashi

Metallic copper of purity equal to commercial electrolytic copper is deposited during the anodic dissolution of technically available white metal, Cu2S, in m acidic solution of' copper(II) sulfate as electrolyte and copper sheets as cathodes. The process may be applied on commercial scale since it has the advantage of by passing the converting and poling steps, decreasing pollution problems due to SO, and recovering the sulfur of the white metal in the elemental form. The anodic dissolution is believed to take place in three steps: The working conditions that lead to 98 pct cathodic current efficiency are: 30 gpl Cu2+ and 100 gpl H2SO4 in electrolyte, current density 1.0 amp per sq dm, and tetnperature of bath 40°C'. DURING the smelting of copper, nickel, lead, and zinc sulfide ores, large amounts of sulfur dioxide are produced. Because the release of this gas in the atmosphere causes pollution problems, many attempts were made in the past for its recovery either in liquified form or processed to sulfuric acid. Although these two forms of sulfur are the usual forms that are consumed by the chemical and metallurgical industries, their storage and transport usually raise economic problems. It was realized, long ago, that a process by which sulfur can be recovered directly in the elemental form would be most attractive. Elemental sulfur is easily stored and transported, and is readily converted to SO2, H2S, or H2SO4 when needed. Processes aimed to recover the metals from their sulfide ores, and at the same time by-product sulfur in the elemental form, were recently reviewed.' As early as 1882, Marchese2 patented a process in which a matte having the composition: Cu 15, Pb 14, Fe 41, and S 25 pct was electrolyzed. According to cohen3 the process was applied on a pilot scale by the Aktiengesellschaft fur Bergbau-, Blei-, und Zinkhiitten-betriebe at Stolberg, Rheinland, Germany. The process was unsuccessful, however, owing to the contamination of the electrolyte during electrolysis. Studies in this field were reported by Bernfeld4 and Egli.5 Borchers et a1.6-8 developed the process further by using white metal (Cu 78.2 pct, S 19.6 pct) instead of the matte, and a pilot plant was operated by the Mansfeldschen Kupferschiefer Co. at Eisleben, German~.~ It appears, however, that the process never went into commercial operation. Further studies in this direction were carried out by Russian workers.10-23 The International Nickel Co. of Canada erected a pilot plant at Port Colborne in 1951 to apply the process to nickel matte which is essentially pure nickel sulfide."'- 26 Full-scale plant went into operation at the Thompson Refinery in Manitoba in 1964.27 In this method nickel sulfide matte is melted and cast into anodes analyzing 76 pct Ni and 20 pct S with small amounts of copper, cobalt, and iron. These anodes are then electrolyzed in an aqueous solution of NiS04 at pH 4. Further work on this method was reported in the literature.28-31 In this paper, experiments on the anodic dissolution of white metal in aqueous copper sulfate solution are reported. EXPERIMENTAL White metal, Table I, obtained from The Anaconda Co., was cast in form of anodes 10 by 7.5 by 1 cm, Fig. 1. The anodes are mechanically strong and do not break easily; when polished they gave a shiny gray metallic appearance. From the chemical composition shown in Table I, it can be seen that the atomic ratio Cu:S corresponds approximately to the formula CU2.06S. The copper in excess to the formula Cu2S is most probably present as a separate phase since metallic copper could be seen under the microscope, Fig. 2. Fig. 3 shows the X-ray diffraction pattern of white metal which matches fairly well with that of reagent-grade Cu2S.

Jan 1, 1969

This discussion was prepared by members of the Phelps Dodge Corpn. staff who were designated to review the minutes. It is confidential but permission has been granted to distribute copies among those who attended the Conference. The minutes of the above conference contain numerous references to the plants and practices of Phelps Dodge Corporation. As many of these references are inaccurate, the following notes are made covering such points: Construction Magnesite Brick in Reverb. Arch (1) An.18" arch, 20 feet long, was built on one furnace with 5 feet on each side of magnesite brick, the center portion .being of silica brick. The furnace was put in operation February 13, 1930 and on April 23rd after 68.8 days' operation it was replaced due to failure of the silica brick forming the center of the arch. At this time, while the silica brick had completely gone, there was 14" of magnesite left. Bridgewall Tapping (2) Tapping matte through the burner wall was first tried at the Copper Queen Smelter in April, 1925. At that time, a copper casting with 1 ½ extra heavy pipes for water cooling cast in it, and having one taphole block was used. Later, on the other (old) furnaces, similar castings, but equipped with two tapholes, were used. We found with these furnaces that we could tap through the burner wall at the beginning of a campaign, but would subsequently have to go back to side wall tapping. This was the case until sometime in 1926. The new furnaces, that went in operation at the beginning of 1927, each had water. cooled castings with two tapholes. These have been used entirely and have been quite successful. Sometime after the furnaces were put into operation sidewall tapholes were put in, simply for the removal of any accumulation of matte that might be temporarily retained at the front end by bridges or dams in the furnace formed by overcharging locally.

Jan 1, 1930

By D. J. Rose, W. M. Armstrong, A. C. D. Chaklader

The wetiability of single crystals of MgO by specimens of vacuum-cast iron was studied using the sessile drop technique in vacuo at 1550ºC. Formation of FeO at the liquid-vapor interface caused the contact angle (6) to decrease from 117 to 65 deg during the first minute. After cooling, all specimens possessed a peculiar annular interfacial deposit of Fe,O,. Within the annulus the interface showed no sign of chemical attack. Chemical reaction occurred where the iron was alloyed with Ti, V, Cr, Nb(Cb), Ta, cmd Zr. Vnriation of 6 with alloy concentration was studied. Although vanadium md chromium improved the wettability of MgO by iron, the effect of Zr, Ti, Nb, and Ta was indeterminable because the 8 derived from sessile drop considerations was that of the metal against a restrictive peripheral volume of liquid oxide wetting the substrate. INTEREST in the nature of metal-ceramic interactions has been stimulated by progressive development of metal-ceramic combinations. One of the more valuable methods used for bond investigation is the sessile drop technique. Recent attempts to improve wettability through solute additions to the drop have revealed that the solute may a) react with the oxide creating new compounds at the solid-liquid interface, b) adsorb at the interface in a monolayer formation, or c) distribute throughout the drop uniformly causing no wettability variation. This work, part m in a series1,2 of investigations of interface reactions between metals and ceramics, embraces a study of the Fe-MgO system. MgO possesses a large negative free energy of formation (-173 kcal per g mole 0, at 1550ºC) compared to FeO at this temperature (-73 kcal per g mole 02). Hence the electronegativity difference between the drop and substrate allows selection from an extensive group of metal solutes with intermediate electronegativity differences that would, in the absence of chemical reactions, be expected to adsorb pre- ferentially at the solid-liquid interface. However, the high oxygen pressure of MgO in vacuo creates an oxidation environment which influences the solute behavior. Recent studies of the Fe-MgO systemJ74 have been restricted by chemical reactions that obscured observations. In view of the current interest in liquid-phase sintering of metal-ceramic combinations under partial oxidizing conditions,5 a more comprehensive study of the Fe-MgO system seemed beneficial. EXPERIMENTAL PROCEDURE 1) Specimen Preparation. Optical-grade MgO single crystals and Ferrovac vacuum-cast iron were used in all experiments. A spectrographic analysis of the iron indicated 0.008 C, 0.05 V, 0.005 Mo, 0.01 Ti, 0.002 S, 0.01 Cr, 0.001 Mg, 0.01 Si, 0.003 A1 (wt pct). The MgO crystals were cleaved along (100) planes into plates approximately 20 by 20 by 1 mm. Following annealing in vactto at 1100°C for 3 hr, surface irregularities were removed by a chemical etch in phosphoric acid at 100°C. The iron rod was machined into small cylinders approximately 0.250 in. in diam and length and these were carefully cleaned in organic and acidic solutions to remove surface impurities. All specimens were weighed to the nearest 0.1 mg. 2) Apparatus. The apparatus described in detail by previous authors1,2 was modified for this work. A Polaroid Land Camera was incorporated into the optical system so that drop measurements at ten-second intervals after melting were possible with ultra-high-speed self-develop ing film. 3) Procedure. The iron cylinders were placed upright on the MgO plates and positioned in the molybdenum susceptor. After furnace assembly the system was pumped down to a vacuum of 1 µ and flushed with H2 at 800°C. The system was again evacuated to 5 x 10-5 mm of mercury and the temperature raised to 1550°C within 2 min. The molten drops were photographed at appropriate time intervals. TWO min after melting the iron vapor pressure caused gas discharge, or corona, within the tube. The specimens were then slowly cooled to room temperature, sectioned and examined metallographi-cally. X-ray identification of interfacial reaction products was attempted by the powder diffraction technique. Alloying elements (Ti, V, Cr, Zr, Ta, Nb) were added to the iron in various concentrations up

Jan 1, 1963

By K. R. Price, M. Gauna

A high seam geologic condition exists at Jim Walter Resources No. 4 mine that requires immediate rib support after a continuous miner cuts a place. High seam mining heights are typically 2.4 to 2.6 m (8 to 9 ft) and a thick rock layer is present in the upper portion of the coal rib side. The 610-m (2000 ft) mining depth at No. 4 mine induces horizontal rib line movement after excavating an entry. Horizontal rib movement greater than 305 mm (12 in.) have been noted. When lateral movement occurs in the high seam areas, the thick rock layer, and the coal above the rock layer, become fractured and tend to roll into the entry. If not adequately supported, large rib rolls develop in the place being bolted as well as in previously mined areas that endanger men and equipment. To control this, rib support must be installed in the roof bolting operation as the bolting crew works toward the face. A rib control system has been developed for this high seam mining condition using a mechanical anchor bolt placed at an angle in the rib and installed with a modified Fletcher DDM-15 bolting machine. More than 120 km (75 miles) of entry have been supported with angle rib bolts. These angle bolts constitute 43% to 60% of the total roof and rib bolt footage in the high seam portions of No. 4 mine. The angle rib bolting system has proven safer, more effective, and more efficient than the earlier support method using bolts installed horizontally into the rib. No rib roll accidents have occurred since the angle drill bolting machines were placed in service in 1981. By securing the broken rib material with an angle bolt anchored above the coal pillar, a more effective means of rib control is achieved. Angle rib bolting does not interfere with continuous miner productivity. In addition, bolting crews are now reduced from three to two people. Total drilling supply costs are about 60% the previous cost, when compared to the previous support method using horizontal rib bolts:

Jan 1, 1985

By J. P. Hirth, A. H. Clauer

A simple graphical method is presented for the determination of climb forces on dislocations exerted by uniaxial stresses. In conjunction with standard stereographic projections, the technique is applicable for any crystal system. Climb forces on glide dislocations in bcc crystals are determined as an application. In connection with a study1 of elevated temperature creep of molybdenum single crystals, a detailed analysis of the climb force on a dislocation was necessary. In general, such forces can be calculated for an arbitrary dislocation segment from the Peach-Koehler equation2 (or one of its variants3"6) where Fk are the components of the force per unit length of dislocation line, ?i of the unit sense vector tangent to the line, ojl of the stress tensor, bl of the dislocation Burgers vector, and is the Einstein permutation operator with components ?123 = ?231 = ?321 = —?132 = — ?321 = —?—213 = unity, and all other components zero. It is understood in the suffix notation of Eq. [I.] that repeated indices are to be summed over 1, 2, and 3. For the most general coordinate system, the matrix manipulations required to solve Eq. [I] are fairly complex. However, a simplification can be achieved by specifying a coordinate system based on the dislocation in question. The pertinent system involves cartesian coordinates xi, x;, xi, with attendant unit vectors e'i; ei being parallel to the Burgers vector b, and e'3; being parallel to the climb directions (b x ?), i.e., normal to the slip plane. In this coordnate system b = (bi, 0, 0) and ? = (?'1,?'2, 0). Hence, Eq. [I] yields for the climb force per unit length F3 = ?'2s'11b'1—?'1s'12b'1 [2] The first term on the right side of Eq. [2] is the climb force on the edge component of the dislocation, while the second is the (cross-slip) force normal to the glide plane acting on the screw component. Thus, the problem of determining the climb force reduces to that of resolving the stress components —il and s'12 in the xi coordinate system. Several authors7- l0 have shown, for the glide case, that such stress resolution can be performed most readily by graphical methods. Therefore, we present a similar method for the climb case. Of the suggested methods, we follow that of Hartley and Hirth,9 which can be performed directly with a standard stereographic projection for the crystal system in question. We treat the case of simple tension, or compression, this being the most common creep test in which climb is important. A set of cartesian coordinates (x1, x2, x3) is fixed with x3 parallel to the specimen axis. This set is connected to the x'i set by the factors defined in Table I. A perspective view of the coordinate systems relating them to the glide ellipse, is given in Fig. 1, while a stereographic projection of the coordinate systems is presented in Fig. 2. The transformation matrix connecting the xi and xi coordinates is x'i =aijXj [3] where an a11 a13 aij = a21 a22 a23 a31 a23 [4] s The corresponding transformation for the stresses is i [5] The only nonzero component of okl for the simple tension case is s33,. Hence, using Eqs. [4] and 151, we find that Eq. [2] becomes F3 = b'1s33 sin2 cos ?[cos ? sin a - sin ? cos a] [6] = m1b'1s033 sin a- rn2b's33 cos a where sin a = 5: and cos a = ?i, with a the angle measured from b to ?, i.e., a polar angle in the x1, x2 plane. The same equation with a sign change applies for compression. A graphical plot of the "Schmid" factor m1, relating to the climb force on the edge component, is presented in the stereographic projection of Fig. 3. In this projection the glide plane normal points toward the top of the page and the glide direction points normal to the plane of the page. To use the graph, one

Jan 1, 1970

By Owen F. Devereux

Two discrete types of microstructure me seen in cermets formed by the reaction: 4Al (liquid) + 3SiO2 (glass) — 2A12O3(a) + 3Si (solid) Relatively coarse-grained macroscopically isotropic specimens resulted from reaction with aluminum containing appreciable silicon, while macroscopically anisotropic fine-grained specimens were formed by reaction with aluminum low in silicon. Optical microscopy, electron microscopy, and X-ray diffraction suggest that the anisotropic material contains gross areas in which submicroscopic grains of a A12O3 are oriented along radial lines drawn from the specimen surface. These lines are presumed to originate at defects in an otherwise protecting surface layer. A unique cermet is formed by the reduction of high-silica glass by molten aluminum according to the reaction: 4A1 (liquid) + 3SiO2 (glass) — 2A12O3 (a) + 3Si (solid) The free-energy change accompanying this reaction is -150 kcal at 800°C; the volume change (volume of A12O3 and silicon minus volume of SiO2) is +6 pct. The reaction product, however, contains aluminum metal as well as Al2O3 and silicon because some of the product silicon is dissolved in the aluminum bath and is replaced by aluminum in the structure. The product is a hard gray solid that retains the external dimensions of the original silica article. The system has been studied in the past, the investigations culminating in patents to George1, 2 and Saw-chuk., The former emphasize that this reaction is but one of a relatively broad class of such systems, while the latter demonstrates that a marked improvement in the gross physical properties of the cermet can be obtained by dissolving appreciable quantities of silicon in the aluminum reactant. The system has also been studied by workers at Rolls Royce Ltd.,4-6 who have patented the addition of small quantities of arsenic, antimony, bismuth, or phosphorus to the reactant bath to SO impede the reaction that glass fibers may be metal-coated by immersion in molten aluminum.

Jan 1, 1969

By P. J. Potter

Practically all tin-base babbitt metals used in engine bearings are made to customers' specifications, which are many and varied. The copper ranges from 3 to 8 per cent. and the antimony from 4 to 13 per cent.; generally, the babbitt with lower copper content will contain from 4 to 8 per cent. antimony and that with higher copper will have from 7 to 13 per cent. antimony. The allowable lead content varies from 0.20 to 2.00 per cent. If a solder is used as a bonding material instead of tin, the resulting material in the finished bearing will have a higher lead content, but it would not be enough to bring the lead above specifica-tional limits. Impurities such as iron, arsenic and bismuth should be determined in the tin before using to insure a uniform and high-grade product. These points must be considered when segregating and grading the waste that comes from the finishing operations on lined bearings. Classification of SCRAP Because of the extremely rigid nature of most of the specifications for bearing linings it is necessary to use the purest of materials as a base for all compositions. The problem of handling secondary metals is confined almost entirely to the recovery of drosses, spills and turnings incident to the manufacturing operations. As a matter of convenience the waste or scrap may be divided into 10 grades, as follows: 1. Tin from pots where tinning operation is carried out. 2. Tin and babbitt spatters from babbitting operation. - 3. Tin skimmings combined with burned zinc chloride. 4. Borings and reamings. 5. Gates from die-cast bushings and bearings. 6. Drosses from die-cast pots, babbitt foundry pots, and pots in babbittiug room. 7. Babbitt with small amount of bronze from machining operations. 8. Babbitt and bronze borings. 9. Scrap bronze-back babbitt-lined bearings. I 10. Scrap die-cast bearings and bushings. A few of these grades of salvaged material have compositions that make it possible to determine beforehand where they may be used to

Jan 1, 1930

By N. O. Gray, John Henderson

Hydrogen-reduction data for naturally occurring single crystals and Prepared polycrystals of dense hematite have been presented. Results cover the temperature range 400o to 1000oC, for particles from ten sources, ranging in size from 0.07 to 10 mm and in shape from spheres to cylinders, cubes, and thin slabs. A consistent pattern of behavior has been demonstrated for single crystals and the reduction mechanism shown to be temperature-dependent. Below 579oC reduction is a simple topochemical process but at higher temperatuves it is complex and occurs in two distinct stages. Prepared particles from these laboratories behave in a similar manner to the single crystals. Data from two investigators showing topochernical reduction of Prepared particles above 575°C are inconsistent with that for other dense hematites. It is concluded that topochenzical reaction should not be used as a model for generalized rate expressions for dense hematites. SINCE 1958, McKewan1-6 has brought to prominence a simple concept of dense hematite reduction. This model is that oxygen is lost from a hematite particle undergoing reduction only from an oxide-iron interface that recedes in such a way that the oxide remaining retains the original shape of the particle, i.e., reduction occurs topochemically. An adjunct to this concept is that any intermediate oxides in the transition from hematite to iron only form thin layers so that oxygen cannot be lost from the particle without movement of the oxide-iron interface. Further, the rate of oxygen loss from the particle is said to be proportional to the area of the receding interface so that the iron layer grows linearly with time and the over-all reduction process can be described by the equation where ro and do are the initial particle radius and density, respectively, R is the fraction of the original oxygen lost, i.e., the fractional reduction, at time t, and K is the rate constant. The idea of an underlying simplicity in hematite reduction is attractive because it gives a tractable basis from which general theories of hematite reduction can be developed and it has received wide support,7-14 based mainly on the large amount of data13 that can be fitted to Eq. [I]. However, despite the fact that this equation has been derived for dense materials, the bulk of the data that have been used to test it13 have been for materials of only about 90 pct of theoretical density (5.26 g cm-3) or less, so that its generality for dense hematites has not been demonstrated. In any case, as will be seen, adherence of reduction data to Eq. [1] does not necessarily imply that reaction occurs topochemically. In this work only data for hematites approaching theoretical density are considered and it will be shown that in only one study besides McKewan's is topochemical behavior observed over the whole range of temperature investigated. For the majority of materials a linear rate of interface advance is observed to complete reduction only when wustite is not a stable intermediate phase in the transition of hematite to iron, i.e., at temperatures below about 575°C. Above this temperature, reduction is an exceedingly complex series of reactions that takes place in two distinct stages and it is only in the first stage that reaction in any way resembles a topochemical process. This means then that, far from representing general behavior as has commonly been supposed, topochemical reaction for dense hematites is only a particular behavior that may be observed under some circumstances. EXPERIMENTAL Hydrogen-reduction data have been collected and cross-checked in these laboratories by three techniques, weight loss, collection of water evolved in the reduction reactions, and direct metallographic examination. Details of these techniques are discussed elsewhere," where it is shown that results obtained by the three methods are in close agreement. The weight-loss method, by which most of the results were obtained, consisted of hanging the sample in a platinum mesh basket from an Ainsworth Model AV-AU-1 vacuum recording balance inside a vertical l 1/4-in.-ID alumina tube furnace. Dry deoxidized hydrogen was flowed downwards through the tube at 2 to 4 liters min-1 (stp). Single crystals from two sources and artificial oxides from three sources have been examined. The single crystals were from hematite deposits at Yampi Sound, Western Australia, and Brazil, the latter being obtained from Gregory, Bottley and Co., London, U.K. The "Yampi Blue" crystals were hand-picked from washed, magnetically concentrated, sized fractions, -200 mesh BSS (mean diameter ca 0.07 mm) and —36 + 44 mesh BSS (mean diameter ca 0.4 mm) while 10-mm cubes were cut from the Brazilian crystals with a diamond saw. The starting materials for the prepared particles were hematites designated, respectively, "Specpure Iron Oxide", Laboratory No. S639 from Johnson Matthey & Co. Ltd., London, U.K., "Calcined Ferric Oxide" from B.D.H. Laboratory Chemicals Division, Poole, U.K., and "Pigment Grade Oxide", EPR-50, from C. K. Williams & Co., Easton, Pa., U.S.A. Approximately spherical particles were prepared from the artificial oxides by rolling the material, moistened if necessary, in a glass jar, and cylindrical compacts approximately 10 mm in diam and of approximately equal height were pressed in a steel die at 200 psi. These spheres and cylinders were subsequently fired in oxygen for 20 to 100 hr at 1370°C. The

Jan 1, 1967

By C. K. Leith

GENERAL GEOLOGY OF THE LAKE SUPERIOR IRON-BEARING AND COPPER-BEARING SERIES. THE geology of the Lake Superior region is of general interest, both from an economic and a scientific standpoint. The presence of large and rich iron- and copper-deposits has made a knowledge of the geology of the region necessary for purposes of exploitation and exploration. The ores of the region are contained in rocks of pre-Cambrian age, 'pith for most of the country up to recent years have usually been referred to as « crystalline schists " or " crystalline complex;" and regarded principally as metamorphosed basement-unit upon which the sedimentary rocks, beginning with the Paleozoic, were laid down. In the Lake Superior re¬gion this pre-Cambrian complex presents an unusual variety of rocks with determinable relations. It has been possible, with the large expenditures which-the magnitude of the iron-mining industry warrants, to work out their stratigraphy to a larger extent than has been possible in almost any other area of pre-Cambrian rocks. The real complexity of Lake Superior geology, the confusion of names and the multiplicity of reports covering small parts of the region, are such that interested persons, other than. geologists directly engaged in the work, may well hesitate to attempt to comprehend the geology of the region as a whole. The following paper is a somewhat elementary outline of the geology of the Lake Superior region with special reference to new developments not yet covered in published reports. Geological information concerning the region has been gath¬ered by mining companies, and by the geological surveys of Michigan, Wisconsin, Minnesota, Ontario, Canada, and the United States.. Perhaps in no other part of the country have the mining men themselves spent such large sums in purely geological work. This has made possible the publication of ,reports and maps by the State and Government surveys in much less time and at far less cost than would have been otherwise possible. The. U. S. Geological Survey is the only organization which has covered all of the region on the United 'States side of the boundary, and as its reports include the in¬formation gathered by the mining companies and State organi

Mar 1, 1905

By C. S. Barrett, C. T. Haller

Twinning in magnesium is known to occur profusely under certain conditions, and when it occurs in polycrystalline materials it brings about a partial or even a complete change in the preferred orientation. The amount of research on this subject, however, has not been in proportion to its importance as a mechanism of deformation and reorientation. Much of the research has been limited to twinning in single crystals. The present study1 concerns polycrystalline sheet, and is an investigation of the twinning produced by plastic deformation as a function of the following variables: 1. Direction and type of deformation. 2. Amount of deformation. 3. Speed of deformation. 4. Temperature of deformation 5. Composition and temper of the sheet. 6. Twins previously produced. 7. Twins previously produced, then annealed. By proper control of these variables it is shown that, on a laboratory scale, samples can be produced that are free from preferred orientations. The materials used were samples of commercial magnesium-alloy sheets with nominal compositions given in Table I. X-ray diffraction was used in most of this work to detect the twins and to estimate the amount of twinning. Since twinning on (102) planes causes a re-orientation of the crystal lattice by 86", it is very easy to study with X-ray diffraction patterns, particularly if one notices the diffraction ring from the basal plane— the 002 reflection. By properly directing the X-ray beam, it is possible to produce 002 reflections from twinned material at, say, the 6 and 12 o'clock positions on the 002 ring, with the untwinned material reflecting to 3 and 9 o'clock positions; and by judging the relative intensity of the arcs on the diffraction ring at these positions, it is possible to judge the amount of twinned material relative to the untwinned. This X-ray method of estimating the amount of twinning is generally superior to metallo-graphic observation, for it was found

Jan 1, 1947

By C. S. Barrett, C. T. Haller

Twinning in magnesium is known to occur profusely under certain conditions, and when it occurs in polycrystalline materials it brings about a partial or even a complete change in the preferred orientation. The amount of research on this subject, however, has not been in proportion to its importance as a mechanism of deformation and reorientation. Much of the research has been limited to twinning in single crystals. The present study1 concerns polycrystalline sheet, and is an investigation of the twinning produced by plastic deformation as a function of the following variables: 1. Direction and type of deformation. 2. Amount of deformation. 3. Speed of deformation. 4. Temperature of deformation 5. Composition and temper of the sheet. 6. Twins previously produced. 7. Twins previously produced, then annealed. By proper control of these variables it is shown that, on a laboratory scale, samples can be produced that are free from preferred orientations. The materials used were samples of commercial magnesium-alloy sheets with nominal compositions given in Table I. X-ray diffraction was used in most of this work to detect the twins and to estimate the amount of twinning. Since twinning on (102) planes causes a re-orientation of the crystal lattice by 86", it is very easy to study with X-ray diffraction patterns, particularly if one notices the diffraction ring from the basal plane— the 002 reflection. By properly directing the X-ray beam, it is possible to produce 002 reflections from twinned material at, say, the 6 and 12 o'clock positions on the 002 ring, with the untwinned material reflecting to 3 and 9 o'clock positions; and by judging the relative intensity of the arcs on the diffraction ring at these positions, it is possible to judge the amount of twinned material relative to the untwinned. This X-ray method of estimating the amount of twinning is generally superior to metallo-graphic observation, for it was found

Jan 1, 1947

By C. S. Barrett, C. T. Haller

TWINNING in magnesium is known to occur profusely under certain conditions, and when it occurs in polycrystalline materials it brings about a partial or even a complete change in the preferred orientation. The amount of research on this subject, however, has not been in proportion to its importance as a mechanism of deformation and reorientation. Much of the research has been limited to twinning in single crystals. The present study' concerns polycrystalline sheet, and is an investigation of the twinning produced by plastic deformation as a function of the following variables: I. Direction and type of deformation. 2. Amount of deformation. 3. Speed of deformation. 4. Temperature of deformation. 5. Composition and temper of the sheet. 6. Twins previously produced. 7. Twins previously produced, then annealed. By proper control of these variables it is shown that, on a laboratory scale, samples can be produced that are free from preferred orientations. MATERIALS AND METHODS The materials used were samples of commercial magnesium-alloy sheets with nominal compositions given in Table I. [ ] X-ray diffraction was used in most of this work to detect the twins and to estimate the amount of twinning. Since twinning on {102} planes causes a reorientation of the crystal lattice by 86°, it is very easy to study with X-ray diffraction patterns, particularly if one notices the diffraction ring from the basal plane the 002 reflection. By properly directing the X-ray beam, it is possible to produce 002 reflections from twinned material at, say, the 6 and 12 o'clock positions on the 002 ring, with the untwinned material reflecting to 3 and 9 o'clock positions; and by judging the relative intensity of the arcs on the diffraction ring at these positions, it is possible to judge the amount of twinned material relative to the untwinned. This X-ray method of estimating the amount of twinning is generally superior to metallographic observation, for it was found

Jan 1, 1946

By Morris Steinberg, John Wulff, Robert Kamm

IN powder metallurgy it has often been observed that shrinkage may occur in one direction and growth in another during sintering. Even in long-time sintering experiments the rate of shrinkage may be different in different parts of the compact. In the fabrication of some parts requiring a constant permeability it is even questionable in some cases whether pressing from one direction should be attempted. These observations require for their interpretation a more detailed study of green or pressed density than has heretofore been available. Usually average density measurements of the whole compact are made and in some cases carefully cut sections are measured. A different approach to the problem was first mentioned by Rakowski1 and also used by Balshin.2 Balshin's diagram is reproduced in Fig r and schematically shows the result of pressing three layers of metal powder with fine intervening layers of graphite. The retarding effect of the die walls and a qualitative example of the density distribution is evident. More quantitative information about the distribution of density within a cold-pressed powder compact would be useful in showing the variation in density in compacts as influenced by the type of powder, shape of die, lubrication during the process, and other variables. Furthermore, information about the cracking of cold-pressed compacts may be obtained from an analysis of the stress distribution within a powder compact, and some information about the stress distribution can be obtained in turn from the density and strain distributions. A more detailed report on some of the present experiments appears in reference 3. PRESENT INVESTIGATION In order to ascertain the density gradients in cold-pressed metal powders, a deformable lead grid within the powder was employed. After pressing in cylindrical dies the ejected compact was radiographed, giving a pattern of the deformed grid. From the radiograph density and deformation from point to point is readily measured. From the radiograph strain distribution and stress trajectories were also determined. The latter also permits the determination of the coefficient of friction at the die wall. This technique indicates that the densest part of a compact pressed from one side is at the top outer circumference and the least dense region at the bottom circumference near the stationary plunger. For some heights of compacts the density at the axis is such that the lower density is at the top rather than at the bottom. So irregular a density distribution is due primarily to die-wall friction. As the ratio of diameter to height of compact is increased the die walls play a correspond¬ingly smaller role. More uniform density

Jan 1, 1947

By John Wulff, Robert Kamm, Steinberg Morris

In powder metallurgy it has often been observed that shrinkage may occur in one direction and growth in another during sintering. Even in long-time sintering experiments the rate of shrinkage may be different in different parts of the compact. In the fabrication of some parts requiring a constant permeability it is even questionable in some cases whether pressing from one direction should be attempted. These observations require for their interpretation a more detailed study of green or pressed density than has heretofore been available. Usually average density measurements of the whole compact are made and in some cases carefully cut sections are measured. A different approach to the problem was first mentioned by Rakowskil and also used by Balshin.2 Balshin's diagram is reproduced in Fig I and schematically shows the result of pressing three layers of metal powder with fine intervening layers of graphite. The retarding effect of the die walls and a qualitative example of the density distribution is evident. More quantitative information about the distribution of density within a cold-pressed powder compact would be useful in showing the variation in density in as as influenced by the type of poKder, shape of die, lubricatioll during the process, and other variables. Furthermore, information about the cracking of cold-pressed compacts may be obtained from an analysis of the stress distribution within a, powder compact, and some information about the stress distribution can be obtained in turn from the derlsity and strain distributions. A more detailed report on some of the present experiments appears in reference 3. Present Investigation In order to ascertain the density gradients in cold-pressed metal powders, a deformable lead grid within the powder was employed. After pressing in cylindrical di" the ejected compact was radiographed, giving a pattern of the deformed grid. From the radiograph density and deformation from point to point is readily measured. From the radiograph strain distribution and stress trajectories were also determined. The latter also permits the determination of the coefficient of friction at the die wall. This technique indicates that the densest Part of a compact pressed from one side is at the top outer circumference and the least dense region at the bottom circumfercnce near the stationary plunger. For Some heights of compacts the density at the axis is such that the lower density is at the top rather than at the bottom. SO irregular a density distribution is due primarily to die-wall friction. As the ratio - diameter to height of compact is increased the die walls play a correspondingly smaller role. More uniform density

Jan 1, 1947

By John Wulff, Steinberg Morris, Robert Kamm

In powder metallurgy it has often been observed that shrinkage may occur in one direction and growth in another during sintering. Even in long-time sintering experiments the rate of shrinkage may be different in different parts of the compact. In the fabrication of some parts requiring a constant permeability it is even questionable in some cases whether pressing from one direction should be attempted. These observations require for their interpretation a more detailed study of green or pressed density than has heretofore been available. Usually average density measurements of the whole compact are made and in some cases carefully cut sections are measured. A different approach to the problem was first mentioned by Rakowskil and also used by Balshin.2 Balshin's diagram is reproduced in Fig I and schematically shows the result of pressing three layers of metal powder with fine intervening layers of graphite. The retarding effect of the die walls and a qualitative example of the density distribution is evident. More quantitative information about the distribution of density within a cold-pressed powder compact would be useful in showing the variation in density in as as influenced by the type of poKder, shape of die, lubricatioll during the process, and other variables. Furthermore, information about the cracking of cold-pressed compacts may be obtained from an analysis of the stress distribution within a, powder compact, and some information about the stress distribution can be obtained in turn from the derlsity and strain distributions. A more detailed report on some of the present experiments appears in reference 3. Present Investigation In order to ascertain the density gradients in cold-pressed metal powders, a deformable lead grid within the powder was employed. After pressing in cylindrical di" the ejected compact was radiographed, giving a pattern of the deformed grid. From the radiograph density and deformation from point to point is readily measured. From the radiograph strain distribution and stress trajectories were also determined. The latter also permits the determination of the coefficient of friction at the die wall. This technique indicates that the densest Part of a compact pressed from one side is at the top outer circumference and the least dense region at the bottom circumfercnce near the stationary plunger. For Some heights of compacts the density at the axis is such that the lower density is at the top rather than at the bottom. SO irregular a density distribution is due primarily to die-wall friction. As the ratio - diameter to height of compact is increased the die walls play a correspondingly smaller role. More uniform density

Jan 1, 1947

By S. S. Lisnyak, B. D. Lichter

An important question in the study of the "hot corrosion" phenomenon (i.e., accelerated oxidation of Ni-Cr-base and Co-Cr-base "superalloys" in the presence of sulfur) is the condition of formation and physico-chemical properties of different sulfides in the system Ni-Co-Cr-S. seyboltl has observed the presence of ((chromium-rich" sulfides of compositions M3S4, and M2S3 in the scales of superalloys after hot corrosion; however, as he points out, much confusion exists as to the identity of sulfides found on Ni-Cr and Co-Cr alloys. According to the literature,&apos; ternary sulfides, e.g., NiCr2S4, (monoclinic structure) and CoCr2S4 (spinel structure) exist in these systems. Therefore, it is likely that these compounds are found in the scale of alloys undergoing hot corrosion. At present this possibility has not been discussed in the literature. Accordingly, we have begun investigation on the properties of ternary sulfides and their mutual interaction. The magnetic and electrical properties of pure NiCr2S4 and pure CoCr2S2 have been previously determined."-&apos; In the present work we have studied the interaction between these sulfides at high temperatures by means of X-ray diffraction and magnetic susceptibility. The measurements were carried out at room temperature after appropriate thermai treatment of samples at high temperatures. For alloys containing the three elements nickel, chromium, and cobalt this interaction may be of importance in the study of the hot corrosion phenomenon. The compounds NiCr2S4 and CoCr2S4 were prepared from stoichiometric amounts of the elements and CoS in the case of CoCr2S4. Samples were mixed and sealed in evacuated silica tubes, slowly heated to 900&apos; to 100O°C, and held at temperature for a total of 120 hr (NiCr2S4) or 80 hr (CoCr2S4) with intermediate re-grinding~. X-ray diffraction showed a pure spinel structure for CoCr2S4 and a monoclinic structure for NiCr2S4. Samples of mixtures of the two ternary sulfides were prepared with different compositions, see Table I. Samples were heated for a total of 80 hr at 900&apos;C in evacuated silica tubes, with one intermediate regrind-ing. The capsules were slow-cooled to room temperature in the furnace. Samples for X-ray diffraction were prepared by placing powder on a glass slide with vaseline. Dif- fractometer traces were obtained on a G.E. XRD-5 diffractometer using a chromium tube and vanadium filter (40 kv and 31 ma). The size of the spinel unit cell was determined from the eight highest angle peaks (80 deg < 2b < 160 deg). Calculated lattice parameters were plotted vs cos B . ctn 0 and extrapolated to 6 = 90 deg. Measurements of the magnetic susceptibility were carried out at room temperature using the Faraday method in a magnetic field of 3000 G and using a Cahn RG automatic microbalance. The system was calibrated from the well-established susceptibilities of platinum and palladium: (Xpt = 0.968 x 10-6 g-1 and Xpd 7 5.04 x 10~6 g-1). The weight of samples were approximately 0.200 g. X-ray diffraction patterns for unsintered mixtures showed Bragg peaks from both the spinel (CoCr2S4) and monoclinic (NiCr2S4) structures. After sintering no monoclinic peaks were observed in samples containing up to 40 mol pct NiCr2S4. However, the spinel peaks were displaced to higher angles with increasing

Jan 1, 1970

By S. H. McFarlane, K. H. Zaininger, G. W. Cullen, C. C. Wang, G. E. Gottlieb

Heteroepitaxy of silicon on stoichiometric spinel has been studied. Both boron-doped (p-type) and arsenic-doped (n-type) single-crystal silicon films have been grown by the pyrolysis of silane on sioichiometric spinel (MgAl2O4) substrates prepared by a flux technique. The spinel crystals are free from strain and subgrains, and exhibit no thermal instability at temperatures employed for silicon deposition. The growth parameters of epitaxial silicon have been studied. Effects of substrate orientation, surface preparation, and growth conditions on the silicon Properties have been determined. The silicon-spinel composite was characterized by X-ray diffraction, electron diffraction, electron microscopy, and optical techniques. Information on epitaxial orientation relationship, defect structures and film-substrate interface has been obtained. A parallel orientation relationship was found between silicon and spinel. The silicon films exhibit no subgrain structures. However, growth pyramids, microtwins, stacking faults, and dislocations are the prevalent defects. The deformation of epitaxial silicon was measured by an X-ray technique. It was found that the epitaxial silicon is strained under compres-sive stress due to the thermal expansion difference between the film and substrate. The stress was estimated using the classical plate theory and beam equation. Electrical properties of the epitaxial silicon have been measured, including resistivity, carrier concentration, and Hall mobility. MIS and vertical through diffused junction structures have been fabricated wing silicon-spinel composite. Information on MIS characteristics, minority carrier life time, and junction properties has been obtained. THE achievement of single-crystal growth of large area silicon semiconductor films on oxide insulating substrates is of technical importance to many solid state electronic devices. The semiconductor-insulator composite structure is also of scientific interest because the heteroepitaxy is determined by the spatial relationship between the atomic arrangement in the substrate and that of the atoms in the appropriate crystallographic plane of silicon. The degree of crystalline perfection of the silicon deposits depends also on the physical condition of substrate surface. Epitaxial growth of silicon on commercial flame fusion Al-rich spinel (MgO:3.3A12O3) has been reported by several investigators.&apos;-4 The lattice of spinel of this composition is distorted. The material cracks and exsolves the excess alumina in the lattice at temperatures (-1200°C) used in fabricating silicon devices. Stoichiometric MgA12O4 spinel exhibits neither lattice distortion nor thermal instability. Results are given on the epitaxial growth and characterization of silicon on stoichiometric spinel. EXPERIMENTAL Fabrication of Silicon-Spinel Composite Structures. The MgA12O4 spinel substrate wafers were prepared from bulk single crystals grown at about 1200°C by a flux technique5 using a PbF2 flux. The crystals are free from strain and subgrains, and exhibit a typical dislocation density of less than 50 lines per sq cm. The crystals are thermally stable without cracking and exsolution of alumina to at least 1500°C. The spinel crystals were oriented for cutting by the Laue X-ray back-reflection method.6 Substrate wafers (about 25 mil thick) of (Ill), (loo), and (110) orientations have been obtained bu cutting the X-ray oriented crystals using a standard type diamond wheel. An accuracy of better than 1/2 deg is maintained throughout the operation. The spinel substrate wafers were mechanically lapped and polished to produce the flat and smooth surface which is required for silicon epitaxy. Lapping was carried out with about 30-µ boron carbide abrasives to obtain a flat coplanar surface. The lapped surface was further polished using successively finer grades of alumina, ending with the 0.3-µ grade. After polishing the wafers generally have a flatness of ±0.4 µ per cm, as revealed by interferometry. Fig. 1 shows (111) oriented MgA12O4 spinel wafers of various shapes.

Jan 1, 1970