Search Documents

By Shiou-Chuan Sun

THE presence of an excessive amount of tough froth in the flotation of minerals, particularly coals, may create trouble in dewatering, filtering, and handling. Froth is also a nuisance in many chemical industries.' This paper presents a study on the destruction of extremely tough froths with intense high-frequency sound. The data indicate that sound waves can be employed for continuous atandsoundwavescan instantaneous defrothing. A powerful high-frequency siren was used in obtaining the data. Also tested was an ultrasonorator of the crystal type with a frequency range of 400, 700, 1000, and 1500 kc per sec and a maximum power output from its amplifier of 198 w. The results, not presented, indicate that as now designed this machine is not suitable for defrothing. Although the sound generators of the magnetostriction type2,3 and of the electromagnetic type'.' were not available, it is beelectromagneticlieved they are capable of producing the required sound intensity for defrothing. The use of ultrasonics for defrothing was suggested by Ross and McBain1 in 1944. Ramsey8 reported in 1948 that E. H. Rose mentioned a supersonic device that broke down flotation froth but with low capacity. The writer has not been able to find any published literature containing practical experiments. Theoretical Considerations The mechanism of defrothing by sound is attributed to the periodically collapsing force of the propagated sound waves and the induced resonant vibration of the bubbles. The collapse of froth is further facilitated by the sonic wind and the heat of the siren. Sound waves can exert a radiation pressure'," against any obstacle upon which they impinge. When a froth surface is subjected to the periodic puncturing of sound waves, the bubbles are broken. According to Rayleigh9 and Bergmann,12 the radiation pressure of sound, P, in dynes per sq cm is given as: P = 1/2 (r+1)i/v where r is the ratio of the specific heats of the medium through which sound is traveling and is equal to 1 on the basis of Boyle's law; i is the sound intensity in ergs per sec per sq cm, and v is the sound velocity in cm per sec. In this case, the accuracy of the formula is only approximate, because a perfect reflection can hardly result from a column of froth. In addition to the radiation pressure, the propagated sound waves cause the bubbles of the froth to have a resonant vibration.'" he vibratory motion of the bubbles causes collision and coalescence, thereby weakening if not breaking the bubble walls. Sonic wind and heat were also generated." The sonic wind can exert pressure on the froth surface, and the heat can evaporate the moisture content of the bubble walls as well as expand the enclosed air. Apparatus The defrothing apparatus, shown in Figs. 1 and 2, consists of a powerful high-frequency siren, a glass or stainless steel beaker of 2-liter capacity with 12.4 cm diam and 17.1 cm height, and a metal reflector. The beaker was placed 2 in. above the top point of the siren. The metal reflector was adjusted to reflect and focus the generated sound waves into the central part of the beaker. Fig. 2 shows the crystal probe microphone used to measure the acoustic intensity and the mandler bacteriological filter employed to introduce compressed air into the beaker for frothing. The apparatus was enclosed in a soundproof cabinet equipped with a glass window. The siren, shown in Fig. 3, consists of a rotor that interrupts the flow of air through the orifices in a stator. The rotor, a 6-in. diam disk with 100 equally spaced slots, is driven by a 2/3 hp, Dumore W2 motor at 133 rps. The frequency of the siren can be varied from 3 to 34 kc. The maximum chamber pressure is about 2 atm, yielding acoustic outputs of approximately 2 kw at an efficiency of about 20 pct. The siren itself is relatively small and can be operated in any orientation. A detailed description of the siren has been given by Allen and Rudnick.11 Collapse of Froth To study the sequence of the collapse of froth, the glass beaker was partially filled with 920 cc water, 100 g of —150 mesh bituminous coal, 0.3 cc petroleum light oil, 0.2 cc pine oil and 1.54 cc Pyrene foam compound. This mineral pulp was agitated for 5 min and then aerated through a mandler filter until the empty space of the beaker, approximately 9 cm high, was filled completely with min-

Jan 1, 1952

By Ulick R. Evans, Maurice Cook

The structural changes in metals brought about by annealing follow-ing a deformation at a low temperature has been the subject of many investigations. No less than eleven metals and alloys have been studied in some detail; namely, aluminum, tungsten,2 iron,3 copperI4 gold, zinc,6 cadmium, tin: lead: brass,1° and cupronickel. As a result, it is possible to frame a qualitative statement of the effect of the degree of deformation and the temperature of annealing on the structure finally attained.

Jan 1, 1925

By Geoffrey Gilbert

The Montana Phosphate Products Co., subsidiary of the Consolidated Mining and Smelting Company of Canada, operates three phosphate properties north and northeast of Garrison, Powell County, Mont. Production of all three is from the same phosphate bed, a 3 to 4-ft. member of the Phosphoria formation, whose outcrop is traceable across the mountains of the Garnet Range in a series of southeasterly pitching folds. Because of topographical differences and of variations in the attitude of the bed, each property has its own mining methods and problems. Most of the phosphate rock produced since 1930 has been shipped to the plant of the Consolidated Mining and Smelting Co. at Trail, B.C., where it is treated with sulphuric acid for conversion to phosphoric acid, which in turn is used to produce various fertilizers. History The occurrence of rock phosphate in Montana has been known since 1910, and the Garrison area was mapped by the United States Geological Survey in 1913. In the nineteen twenties William Anderson, owner of a ranch 8 miles north of Garrison, discovered phosphate on his land, and the Montana Phosphate Co., which later became the Montana Phosphate Products Co., was formed to work the deposit. Montana Phosphate Products Co. later obtained United States leases on two adjoining parcels of ground, and this combined property, known as the Anderson mine, has been the main source of Con-solidated's phosphate rock. The mine now includes an adjoining parcel leased from Anaconda and mined from the Anderson workings. In 1940, the Graveley mine, a small privately owned property 6 miles east of the Anderson, was leased from the owner by Montana Phosphate Products Co., and a U. S. lease held by Graveley on some adjoining ground was subleased. In 1943 the Luke mine, on the Mineral Hill property, 1 3/4 miles south-southwest of the Graveley, a U. S. lease, which previously had produced a few thousand tons, was optioned from the lessees by Montana Phosphate Products Co., and is now being developed. At both these mines the rock is appreciably higher grade than at the Anderson mine. Geology The Phosphoria formation is the Permian member of an extensive sequence of Paleozoic and Mesozoic rocks. It is underlain by Pennsylvanian (Quadrant) quartzite and Mississippian limestone, and overlain without any marked unconformity by Jurassic (Ellis) shale and Cretaceous shale and sandstone. In the Garrison area, the Phosphoria itself consists mainly of about 50 ft. of gray to yellow chert. Immediately below the chert is the phosphate, usually 3 to 4 ft. thick. Below the phosphate occur a few

Jan 1, 1948

By Geoffrey Gilbert

The Montana Phosphate Products Co., subsidiary of the Consolidated Mining and Smelting Company of Canada, operates three phosphate properties north and northeast of Garrison, Powell County, Mont. Production of all three is from the same phosphate bed, a 3 to 4-ft. member of the Phosphoria formation, whose outcrop is traceable across the mountains of the Garnet Range in a series of southeasterly pitching folds. Because of topographical differences and of variations in the attitude of the bed, each property has its own mining methods and problems. Most of the phosphate rock produced since 1930 has been shipped to the plant of the Consolidated Mining and Smelting Co. at Trail, B.C., where it is treated with sulphuric acid for conversion to phosphoric acid, which in turn is used to produce various fertilizers. History The occurrence of rock phosphate in Montana has been known since 1910, and the Garrison area was mapped by the United States Geological Survey in 1913. In the nineteen twenties William Anderson, owner of a ranch 8 miles north of Garrison, discovered phosphate on his land, and the Montana Phosphate Co., which later became the Montana Phosphate Products Co., was formed to work the deposit. Montana Phosphate Products Co. later obtained United States leases on two adjoining parcels of ground, and this combined property, known as the Anderson mine, has been the main source of Con-solidated's phosphate rock. The mine now includes an adjoining parcel leased from Anaconda and mined from the Anderson workings. In 1940, the Graveley mine, a small privately owned property 6 miles east of the Anderson, was leased from the owner by Montana Phosphate Products Co., and a U. S. lease held by Graveley on some adjoining ground was subleased. In 1943 the Luke mine, on the Mineral Hill property, 1 3/4 miles south-southwest of the Graveley, a U. S. lease, which previously had produced a few thousand tons, was optioned from the lessees by Montana Phosphate Products Co., and is now being developed. At both these mines the rock is appreciably higher grade than at the Anderson mine. Geology The Phosphoria formation is the Permian member of an extensive sequence of Paleozoic and Mesozoic rocks. It is underlain by Pennsylvanian (Quadrant) quartzite and Mississippian limestone, and overlain without any marked unconformity by Jurassic (Ellis) shale and Cretaceous shale and sandstone. In the Garrison area, the Phosphoria itself consists mainly of about 50 ft. of gray to yellow chert. Immediately below the chert is the phosphate, usually 3 to 4 ft. thick. Below the phosphate occur a few

Jan 1, 1948

By W. C. Winegard, C. Feng, C. Elbaum

SEVERAL investigations have been made concerning the effect of oxygen on the mechanical properties of titanium 1-6= In particular, the yield strength has received considerable attention. Finlay and snyder2 report a 0.2 pet strain offset yield strength if 49 kg per sq mm in titanium containing 0.1 pct 0 and 61 kg per sq mm in titanium with 0.2 Pct 0. These results are in good agreement with those of Jaffee, Odgen, and Maykuth3 who report values of yield strength

Jan 1, 1960

By John B. Pearse

The works heretofore used in carrying out the Bessemer process have been constructed substantially as follows: The whole works or plant has been divided into three parts. 1. The division in which the metals for conversion are melted. 2. The division in which the metals are converted into steel and cast into ingots, or the converting department. 3. The engine and boiler department which supplies the hydraulic power required to move the machinery, and which furnishes the blast used for converting the crude metal into steel.

By Charles Austin

IN a recent paper the authors1 discussed the reactions to tempering of hypereutectoid steels quenched from 1000° C., as revealed by studies on changes in hardness, electrical resistivity, coercive force and metallo-graphic characteristics. The data, which related specifically to temper-ing temperatures of 550°, 650° and 710° C., for varying periods up to 125 hr., permitted the following important conclusions: 1. The rate of softening of the steels at the temperatures examined differed markedly although the steels were of "similar" general chemi-cal composition. 2. The temperature of maximum softening spread over a range from about 650° C. to the eutectoid inversion. 3. The divergence in behavior was ascribed, at least in part, to a profound difference in tendency to graphitization on annealing at sub-eutectoid temperatures. 4. The mode of spheroidization of the cementite, as revealed by metallographic studies, also varied considerably in the different steels. The purpose of the present investigation is to pursue further the study of the difference in behavior of the steels on tempering over a wider range of temperature. To this end the following features have received particular attention: 1. Comparison of temperatures of maximum softening of the various steels when the quenched samples were tempered for 5 hr. and for 75 hr. followed by furnace cooling and by quenching in water. 2. Determination of the effect of quenching temperature, prior to tempering, on the rate of softening. Quenching temperatures of 1000° and 850° C. were used in the investigations. 3. Examination of the microstructures obtained with the various heat-treatments employed.

Jan 1, 1938

By B. S. Norris, Charles R. Austin

IN a recent paper the authors1 discussed the reactions to tempering of hypereutectoid steels quenched from 1000° C., as revealed by studies on changes in hardness, electrical resistivity, coercive force and metallographic characteristics. The data, which related specifically to tempering temperatures of 550°, 650° and 710° C., for varying periods up to 125 hr., permitted the following important conclusions: 1. The rate of softening of the steels at the temperatures examined differed markedly although the steels were of "similar" general chemical composition. 2. The temperature of maximum softening spread over a range from about 650° C. to the eutectoid inversion. 3. The divergence in behavior was ascribed, at least in part, to a profound difference in tendency to graphitization on annealing at subeutectoid temperatures. 4. The node of spheroidization of the cementite, as revealed by metallographic studies, also varied considerably in the different steels. The purpose of the present investigation is to pursue further the study of the difference in behavior of the steels on tempering over a wider range of temperature. To this end the following features have received particular attention: 1. Comparison of temperatures of maximum softening of the various steels when the quenched samples were tempered for 5 hr. and for 75 hr. followed by furnace cooling and by quenching in water. 2. Determination of the effect of quenching temperature, prior to tempering, on the rate of softening. Quenching temperatures of 1000° and 850° C. were used in the investigations. 3. Examination of the microstructures obtained with the various heat-treatments employed.

Jan 1, 1938

By M. L. Samuels

In a recent paper the authors1 discussed the reactions to tempering of hypereutectoid steels quenched from 1000' C., as revealed by studies on changes in hardness, electrical resistivity, coercive force and metallo-graphic charaeteristics. The data, which related specifically to tempering temperatures of 550°, 650" and 710" C., for varying periods up to 125 hr., permitted the following important conclusions: 1. The rate of softening of the steels at the temperatures examined differed markedly although the steels were of "similar" general chemical composition. 2. The temperature of maximum softening spread over a range from about 650" C, to the eutectoid inversion. 3. The divergence in behavior was ascribed, at least in part, to a profound difference in tendency to graphitization on annealing at sub-eutectoid temperatures. 4. The mode of spheroidization of the cementite, as revealed by metallographic studies, also varied considerably in the different steels. The purpose of the present investigation is to pursue further the study of the difference in behavior of the steels on tempering over a wider range of temperature. To this end the following features have received particular attention: 1. Comparison of temperatures of maximum softening of the various steels when the quenched samples were tempered for 5 hi. and for 75 hr. followed by furnace cooling and by quenching in water. 2. Deterrnirlation of the effect of quenching temperature, prior to tempering, on the rate of softening. Quenching temperatures of 1000" and 850" C. were used in the investigations. 3. Examination of the microstructures obtained with the various heat-treatments employed.

Jan 1, 1938

By M. L. Samuels

In a recent paper the authors1 discussed the reactions to tempering of hypereutectoid steels quenched from 1000' C., as revealed by studies on changes in hardness, electrical resistivity, coercive force and metallo-graphic charaeteristics. The data, which related specifically to tempering temperatures of 550°, 650" and 710" C., for varying periods up to 125 hr., permitted the following important conclusions: 1. The rate of softening of the steels at the temperatures examined differed markedly although the steels were of "similar" general chemical composition. 2. The temperature of maximum softening spread over a range from about 650" C, to the eutectoid inversion. 3. The divergence in behavior was ascribed, at least in part, to a profound difference in tendency to graphitization on annealing at sub-eutectoid temperatures. 4. The mode of spheroidization of the cementite, as revealed by metallographic studies, also varied considerably in the different steels. The purpose of the present investigation is to pursue further the study of the difference in behavior of the steels on tempering over a wider range of temperature. To this end the following features have received particular attention: 1. Comparison of temperatures of maximum softening of the various steels when the quenched samples were tempered for 5 hi. and for 75 hr. followed by furnace cooling and by quenching in water. 2. Deterrnirlation of the effect of quenching temperature, prior to tempering, on the rate of softening. Quenching temperatures of 1000" and 850" C. were used in the investigations. 3. Examination of the microstructures obtained with the various heat-treatments employed.

Jan 1, 1938

By G. Cartaud, F. Osmond

We have already devoted two previous memoirs to this question. In the firstL we collated and discussed the existing literature on the subject; in the second: we described the crystalline forms obtained by the reduction, at different temperatures, of ferrous chloride by hydrogen or by zinc-vapor. The conclusion from these researches was that the three allo-tropic states of iron—a, stable below A2; , stable between A2 and A3; and , stable above A3—all crystallize in the cubic system. The differences observed were such as are customarily encountered in the crystallographic records of many minerals of which allotropic varieties or isomerides are not known, and did not conform to the ordinary definition of polymorphism. It is, however, improbable that allotropic transformations, which are placed beyond doubt by a series of positive facts, do not involve some changes in the intimate structure. As a matter of fact, the crystals we did obtain were too small to allow of a precise examination, and this might introduce an element of uncertainty in the firm establishment of our conclusions. Professor H. Le Chatelier mas even led to think from some of our results that r-iron could very well be a rhom-bohedron simulating a cube, and not a true cube, and it will be remembered that the crystalline form of bismuth was for a long time incorrectly regarded as cubic. Allotropy does not, however, necessarily involve such a deduction. Without departing from the cubic system at all, a whole

Jan 1, 1907

By B. W. Gonser, C. M. Heath

The importance of grain size and its control in wrought brass needs no lengthy discussion, since specifications so often make exact control imperative. Aids to this control are therefore of interest. The effect of a number of different elements on the grain growth of brass under various conditions of annealing has been reported in the technical literature. In particular, a paper by Cook and Miller1 a few years ago, with the discussion that followed, gave valuable information on the effects of iron, phosphorus, manganese, aluminum, aluminum plus nickel, and aluminum plus silicon. Price12 in his discussion of that paper, added a description of some commercial brasses that exhibited a grain-refining effect owing to the presence of 2 per cent A1 and 1 per cent Ni. Gibson and Doss3 have recently given data on the effect of iron on annealing high brass. No comprehensive study, however, has been given to the effect of additions of chromium. It has been the purpose of this investigation to determine the effect of adding various amounts of chromium to a plain cartridge brass, particularly in regard to the effect on grain growth in various annealing treatments after cold-working. Prepakation of Alloys Alloys of high-purity brass of 68.5 Cu, 31.5 Zn composition were made containing from 0 to 0.17 per cent Cr. These were produced in induction furnaces, using unlined graphite crucibles to hold the charge. The melts were cast into rectangular chill molds giving ingots about % by 3 by 10 in. in size.

Jan 1, 1938

By C. M. Heath, B. W. Gonser

The importance of grain size and its control in wrought brass needs no lengthy discussion, since specifications so often make exact control imperative. Aids to this control are therefore of interest. The effect of a number of different elements on the grain growth of brass under various conditions of annealing has been reported in the technical literature. In particular, a paper by Cook and Miller1 a few years ago, with the discussion that followed, gave valuable information on the effects of iron, phosphorus, manganese, aluminum, aluminum plus nickel, and aluminum plus silicon. Price12 in his discussion of that paper, added a description of some commercial brasses that exhibited a grain-refining effect owing to the presence of 2 per cent A1 and 1 per cent Ni. Gibson and Doss3 have recently given data on the effect of iron on annealing high brass. No comprehensive study, however, has been given to the effect of additions of chromium. It has been the purpose of this investigation to determine the effect of adding various amounts of chromium to a plain cartridge brass, particularly in regard to the effect on grain growth in various annealing treatments after cold-working. Prepakation of Alloys Alloys of high-purity brass of 68.5 Cu, 31.5 Zn composition were made containing from 0 to 0.17 per cent Cr. These were produced in induction furnaces, using unlined graphite crucibles to hold the charge. The melts were cast into rectangular chill molds giving ingots about % by 3 by 10 in. in size.

Jan 1, 1938

By W. L. Dennen, V. H. Wilson

This paper is a description of the opera-tion and results of a Humphreys Spiral Silt Cleaning Plant at the Powderly Colliery 01 The Hudson Coal Co. during the first nine months of operation and follows a preliminary description given at the .Institute cite Institute in May, 1947, in a paper titled "Preparation of Anthracite Silt for Boiler Fuel in a Humphreys Spiral Test Plant" by H. H. Otto, V. H. Wilson and W. L. Dennen. This plant is considered a full size op-erating test plant and, like all new plants, numerous minor changes in the methods of operation have been made from time to time to secure the results desired. Views of the silt preparation plant and of the screening house are given in Fig I and 2. This plant consists of 48 spirals in 8 batteries of 6 spirals each, 36 of which were to be operated as primary spirals and the remaining 12 as secondary spirals. A brief description of the plant and its operation follows. The only material cleaned at the plant during 1947 was that carried in the underflow from the Thickener which han-dles the Breaker waste water. This under-flow, amounting to approximately 2000 gpm of water and containing 12.6 pct of solids, is pumped to vibrating screens where the plus 3/16-in. material is removed. (Fig 3). This oversize material drops into a pocket from which it is trucked to the run-of-mine tipple for re-preparation.

Jan 1, 1949

By Murray F. Hawkins

Horner1 and van Everdingen8 ave shown that the pressure drop within the wellbore, as a result of having produced the well at a constant rate q for time t, where t is sufficiently large, is: van Everdingen observed that better agreement between theory and well performance can be obtained if, instead of assuming the permeability is kc everywhere about the well, it is assumed the permeability near the well-bore is substantially reduced as a result of drilling, completion and/or production practices. In order to account for the additional pressure drop he introduced the dimensionless quantity S, the skin effect factor, so that Eq. 1 becomes: Eq. 2 might have also been obtained as follows. Assume a zone of altered permeability k, exists about the well out to a radius r and beyond that the unaltered, external permeability k. The additional pressure drop required to overcome this skin of reduced permeability may be calculated with sufficient accuracy using the incompressible flow equation; for Browns-combe and Collins1 have shown almost no difference between compressible and incompressible steady-state flow, in the vicinity of the wellbore, and the small volume of fluid in the vicinity of the wellbore makes unsteady-state mechanics unnecessary. Then. The sign of this skin pressure drop will be positive or negative depending upon whether the altered permeability k, is smaller or larger, respectively, than the external permeability k... Adding the pressure drop of Eq. 3 to Eq. 1 to find the total pressure drop: Comparing Eq. 4 with Eq. 3 it is seen that the skin effect may be defined by: be determined from pressure build-up tests1,3,4,5,6,7,8 The average permeability kavg including the altered and external permeabilities, can be determined from PI tests, and may be defined approximately on the basis of steady-state flow, as was done by Thomas' in defining the damage factor, by: The productivity ratio is the ratio of the average to the external permeability, kavg/ke or This equation shows that the productivity ratio and the skin effect are not uniquely related, because of the uncertainty in the drainage radius, and also, in many instances, the wellbore radius. Fortunately, they enter in the logarithm. The curves of Fig. I are plots of Eq. 8 for values from 100 to 50,000. The points represent the skin effects and corresponding productivity ratios from a large number of well tests, taken from Fig. 15 of Ref. 5 or Fig. 13 of Ref. 9. While some of the data

Jan 1, 1957

By Wm. Reuben Webster

BRASS is an alloy of copper and zinc. The brasses (using this term to denote all useful proportions of the two constituents) are the most valuable and widely employed of all [ ] nonferrous alloys, because of their high resistance to ordinary corrosive agencies and the very wide range of properties that may be imparted to them by variations in the proportions of the constituents and by variations in mechanical treatment and heat-treatment. Fig. I shows the normal physical properties, as determined by standard tensile tests, of the series when in the annealed condition. Fig. 2 shows the effect of varying amounts of cold-working on an almost pure brass containing 70 per cent copper and 30 per cent zinc. Fig. 3 shows the effect of annealing at various temperatures on the same alloy. This effect is somewhat modi- [ ] fied by the degree of cold-working to which a brass has been subjected, as shown by Fig. 4. A fourth test, which is empirical, has been found useful because of its simplicity the hot hammer test. Samples 1/2 in. in diameter and 3/4 in. long are placed in a suitable furnace. These are withdrawn one at a time at successively higher temperatures and are subjected to the blow of a drop hammer weighing 50 lb. with a drop of 4 ft. The percentages of reduction in length of the cylinders are plotted against temperatures and give a comparative measure of plasticity at different temperatures. The results of this test on several

Jan 1, 1942

By Robert J. Evans

An in-seam tester, which is a hydraulically activated single-pick instrument to measure and record pick cutting forces, was designed and fabricated to establish criteria necessary for the design and development of a water-jet-assisted rotary drum cutting system using moderate-pressure jets (3,000 to 10,000 psi). Data are presented for cutting trials in a simulated coal block and underground in the Pittsburgh coal seam for water-jet assist and dry cutting. Data analysis indicates that water-jet assist significantly reduces pick forces.

Jan 1, 1984

By Clifford S. Wilson

ScReened pipe is designed with the view of restraining the fine, free-running sands of the production zone from entering oil wells. Its successful use is dependent on a number of factors. The nature and effects of some of these factors can be determined through experiment and observation, but some of the elements that have a distinct bearing on the use of screened pipe can be evaluated only by estimate. The important subsurface conditions which affect the use of screened pipe are: 1. Depth of production zone. 2. Extent of production zone. 3. Reservoir pressure. 4. Character and relative quantity of oil and gas. 5. Character of sediments: a. Cossolidation of beds. b. Variation in beds. c. Grain-size gradation of sands. d. Free-running characteristics of sand from different levels. Aside from the use of mechanical equipment and tools, the measures to be taken in the installation of screened pipe involve: 1. Size of liner. 2. Length of liner. 3. Design and mesh of screen. 4. Portion of liner to be screened. 5. Manner of setting liner. 6. Preparation of or washing of the well before or during the setting of the screen. 7. Manner of bringing in the well. 8. Manner of flowing the well. Values applicable to the actual subsurface conditions that exist at any well can only be approximated. The accuracy of the estimate will be measured by the amount and quality of the evidence at hand and the personal factor of ability to interpret the evidence fairly, whether

Jan 1, 1933

By Michael Tenebaum

IN a previous investigation1 the authors studied the effect of pressure on the reduction of iron ores by hydrogen. With hydrogen as a reducing agent, the rate of reduction was increased substantially by increasing the pressure from 1 to 2 atmospheres. The results with hydrogen prompted the present study of the effect of pressure on reduction with carbon monox-ide and with mixtures of carbon monoxide and nitrogen. FEATURES OF REDUCTION PROCESS The gas stream in the lower part of the blast furnace always contains sufficient concentrations of reducing gases to complete reduction provided sufficient time is allowed for the reaction to proceed. Reducing gases react immediately with the iron oxide on the surface of lumps of ore. However, as the unreduced surface recedes from the easily accessible exterior of the lump, the reaction proceeds by virtue of the diffusion of the gases into and out of individual pieces. The rate of diffusion of gases, which undoubtedly plays an important role in the reduction of iron ores, depends on several factors, most impor-tant of which are: (1) molecular weight or density, (2) pressure, (3) tem-perature, (4) concentration gradient. Thus, the rate of reduction of a lump of iron ore at any temperature will depend not only on the specific reaction rate but also upon: (1) available surface of unreduced iron oxide, (2) rate of diffusion of the reducing gas to the reacting surface, (3) rate of effusion of the gaseous products of the reaction from the reacting surface, (4) adsorption of the gases on the reacting surface.

Jan 1, 1939

By F. F. Frick, Frederick Laist

In a leaching process, having obtained the copper in solution, the choice of the precipitation method is influenced by the following factors: 1. Availability of precipitant. 2. Adaptability to the leaching process. 3. Final product desired. 4. Regeneration of leaching solutions. 5. Fouling of solutions. There are three general classes of precipitation methods: 1. The use of iron, scrap or sponge. 2. Electrolytic deposition. 3. The use of some gas or reagent by which the copper is obtained, usually in the form of an intermediate precipitate which requires further treatment. For example, the precipitation of, the copper as Cu2Cl2 from chloride solutions; with SO2 gas. The use of iron is adapted to almost any process. It has the great advantage of extreme simplicity, and the recovery of the copper and any values present in a highly concentrated, easily treatable form. The disadvantages are the cost in isolated places, the uncertainty of the scrap-iron market, and the fouling of the leaching solutions. The latter is a serious factor, when a reagent such as salt is used in them, which makes necessary their re-use. Where applicable, electrolytic deposition is very attractive. The copper is obtained in a form directly marketable, there is a regeneration of acid and no fouling of solutions. Unfortunately, chloride solutions do not lend themselves to electrolysis. An entirely satisfactory anode material has not yet been discovered, although magnetite, apart from being rather brittle, seems to answer the requirements fairly well. The use of a method of the. third class is involved in many special

Jan 1, 1915