Search Documents

By H. B. Hunter, F. G. Stone, F. J. Dunkerley

Introduction and Literature Survey This is the second in a series of papers coming from this laboratory on the correlation of the low temperature tensile properties of tin-binary alloys with microstructure. These engineering data and those of the previous paper1 were obtained as the initial part of a long-range program to determine the changes in the fundamental mechanical properties accompanying the beta to alpha phase change in tin and its binary alloys below 13.2°C. Since it appears now that the more fundamental studies will be delayed,* and since no summary of the low temperature properties of these tin-base white bearing alloys was found in the literature, it was decided to publish all the engineering data thus far obtained. Accordingly, the tensile properties of thirteen binary alloys containing from 0.1 to 60 pet cadmium and 0.1 to 10.43 pet antimony measured at six temperatures from —196 to +23°C are presented here and their variations rationalized in terms of microstructure. A literature search showed that these systems had not been investigated at low temperatures, although both the tin-cadmium and tin-antimony2,3,4,5 and the tin-rich corner of the ternary system67 have been studied at room temperature. Hanson and Pell-Wal-pole5 and Homer and Plummer4 determined the tensile properties of alloys containing from 0 to 10 pet cadmium. The same authors3 determined the tensile strength and elongation in the tin-antimony system from 2 to 18 pet antimony at room temperature while Pell-Walpole et al.6,7 studied the properties of high tin and tin-antimony-cadmium alloys. Since there were many variables besides composition in these tests, it was difficult to make a valid comparison with the room temperature data of the present study, but in general the tensile strength and ductility values are in reasonable agreement. Pell-Walpole2 also determined the effect of grain size on the tensile strength of pure tin and 1 pet alloys of both antimony and cadmium. The true maximum stress was found to decrease exponentially as the number of grains in the cross-section increased. This effect of grain size was strikingly revealed in the present work, as indicated in a later section. Hanson and Pell-Walpole8 placed the solid solubility limit of antimony in tin at 3.5 pet at 20°C, increasing to 4 pet at 190°C, and then sharply increasing to 10.3 pet at 246°C (the latter being a peritectic point). Their results are in disagreement with those of previous investigators,9 and the discrepancy seems to lie in the micro-graphic observation of the second phase

Jan 1, 1950

By Henry Louis

The object of the present paper is to describe a primitive method of gold-extraction, practiced by a small colony of Chinese in the district of Tomoh, one of the Siamese-Malayan States. This district has been worked for gold about 150 years, but has been only twice or thrice visited by Europeans, who are looked upon with a good deal of jealousy by the miners. The gold-district, covering not more than 10 square miles, is situated about Lat. 5' 47l N. and Long. -101' 39 E., on the headwaters of the river Teluban. It is a very mountainous region, lying on the northern flanks of the great range that forms the watershed between the rivers Patani, Kelantan, Teluban, etc., on the north and Perak on the south. The gold occurs in narrow veins and leaders of quartz, intersect- ' ing and intercalated among irregularly upheaved and contorted, highly metamorphosed, micaceous and chloritic schists. These veins vary between 3 inches and 3 feet in thickness, and are sometimes very rich. The geology of this region is thus very similar to that characterizing gold-regions all over the world; if must, however, be.

Jan 1, 1892

Dr. Oldshue has provided a useful summary of a voluminous subject and my task will be to select and direct attention to those areas of mixing theory and practice which are germane to mineral processing in general, and to fine particle treatment in particular. Pulp mixing in impeller actuated reactors occurs in mineral processing in several different applications: (1) emulsification of reagents; (2) mixing pulp with 'reagents as in conditioning for subsequent operations (such as flotation, flocculation or agglomeration) ; (3) high intensity agitation, as in (a) disintegrating and dispersing aggregates, and (b) aggregating particles as in shear flocculation or in selective agglomeration; (4) hydrometallurgy; (5) hydrometallurgy with gas phase (e.g., Arbiter process); . (6) flotation in sub-aeration machines. Attention is invited to 3 above in which two opposite effects can be induced by proper choice of chemical treatment and hydrodynamic conditions. Successful processes for treating mineral fines require excellent aggregate dispersion in order to fully accomplish the liberation stage. Some processes depend further upon selective aggregation following dispersion. The term “dispersion” is often used in different senses which for present purposes will be clarified at the bottom of the next page.

Jan 1, 1979

By S. E. Hasko

It is the purpose of this note to report the crystal-lographic data for nine new B5A compounds* having the Cu5Ca structure, with A a rare earth and B a transition element, Co, Ni or Cu. In previous papers, some magnetic data1 and preparation and crystallo-graphic data2 for other B5A compounds having the same structure have been reported. Crystallographic data for these compounds are shown in Tables I and 11. These results are in agreement with others of this series reported previously by Wernick and ~eller.' The abnormally large atomic volume of Yb metal3 is not manifested in Ni,Yb, when one compares it with the compounds reported here and the data of reference 2. This is not true for the compound YbAl,, having the cubic Laves structure (MgCuz), to be discussed in other papers.4'5 Thus, it appears that Yb has a valence of 3; i.e., the 2 s and Id electrons are lost to the conduction band.4'5 Lattice constants for four of these compounds prepared by levitation melting have been reported by Nassau, Cherry, and wallace.' The lattice constants

Jan 1, 1961

By William Ide Pierce

It is often desirable to work an old mine that has not been in operation for some time arid that is filled with water. This is especially true in Nova Scotia, where no great depth has yet been reached in any of the mines. The following is a description of a self-dumping water-tank which was used by me at Tangier, for draining a mine, and which did the work of a large pump, while the original cost is merely nominal, in comparison with the price of a pump. The tank, A, Pig. 1, is 1 1/3 by 3 feet and 4 feet high, inside measurement, made of 2-inch stuff and securely bound with iron. There are two clacks in the bottom which open as the tank is lowered into the water, and which close and hold the water as the tank is raised. B is an iron rod running through the tank, below and back of the center, and projecting beyond the sides of the tank. C is one of two guides, and D, a movable iron rod in each guide. This rod, attached to an upright, E, is moved forward and close up

Jan 1, 1886

By L. D. Jaffe

IT is now well established that quenched and tempered titanium alloys have much better ductility when the quenching is from a two phase a-B structure, rather than from an all B structure. The corresponding microstructural differences, however, have not been shown in previous publications. Accordingly, specimens were cut from a % in. rod of commercial RC-130A, containing 7.9 pct Mn and 0.12 pct C, which had been previously hot rolled, heated 1 hr at 1100°F, and air cooled. (The same heat has been studied by others." 7 Samples about 1/4 in. cube were heated in helium 1/2 hr at 1450' or 1700°F, quenched in brine, tempered in helium 1 hr at various temperatures up to 1250°F, and quenched in brine. They were then sectioned and metallo-graphically examined, using an etchant of HF-HNO, in glycerine. As quenched from 1700°F, the microstructure observed was clear /3. (Probably also present was U, as the hardness was 400 Vhn, but w is not yet reliably revealed by any metallographic technique.) When the /3 quenched alloy was tempered at a high temperature, a precipitated as a grain boundary film

Jan 1, 1957

By E. Buehler, E. Berry

HE magnetic properties of dilute palladium alloys are of fundamental interest.''' Neutron diffraction studies3 have indicated that a better understanding of the behavior of these alloys could be realized with the availability of high-purity single crystals of palladium. Crucible melts of 99.999 pct pure palladium were found inadequate for such research. In a successful effort to fill this need, floating zone refining of palladium was undertaken. In this note the results of the initial experiments are reported. Zoning was accomplished in an argon atmosphere using 450 kc rf generator for an energy source. Samples 5 to 6 mm in diam were suspended in a gastight quartz envelope which could be moved vertically through the rf coil. A nominal upward traverse rate of 1.5 mm per min was maintained during a pass. Close coupling was found to be essential for stable retention of the liquid in the zone. Single crystals averaging 3.5 cm in length were obtained. Laue photography showed them to be continuous single crystals without gross imperfections. Several criteria were used for evaluation of the purity of the zoned material: magnetic behavior, low-temperature specific heat and residual resistivity ratios. Table I shows the residual resistance ratios obtained for two samples, one subjected to a single pass, the other zoned four times. It is appilrent that palladium can be zone refined with the electrically active impurities being transported toward the tail end. A decrease in susceptibility for zone-melted specimens over any previously measured material from 1.5" to 80'~ has been obserted by H. J. Williams and R. C. Sherwood4 substantiating the residual resistance data. The specific heat measurements are currently being made3 and will be published at some later date. Discussions with J. H. Wernick and S. C. Abrahams are acknowledged. We also wish to thank G. F. Brennert for the residual resistance measure ments.

Jan 1, 1962

By Kenneth K. Humphreys, J. W. Leonard, T. S. Spicer

INTRODUCTION Reasons for Thermal Drying The continuing increase in the percentage of - '/4 in. ( -6.3 mm) coal produced as a result of the increased use of mechanical mining methods has, over the years, tended to shift considerable portions of the work of producing salable coal to the fine coal cleaning section of the preparation

Jan 1, 1979

By Albert Sauveur

My first paper dealing with the theories of the hardening of steel by rapid cooling was published in the Transactions of this Institute in 1896— 30 years ago-under the title "The Microstructure of Steel and the Current Theories of Hardening," hence, also, the title of the present paper. It was extensively discussed and was, I believe, one of the starting points of many subsequent papers and discussions of the same subject, dis-cusssions which at times became almost violent and which led to the formation of different schools such as the "Carbonists" and the "Allo-tropists." Some of the older members of the Institute, who took part in the debate or who were interested observers, will, I am sure, have kept a vivid remembrance of it. The controversy gradually quieted down, apparently for lack of ammunition, without any side acknowledging defeat. Recently, however, interest in it ha been revived through the claims of some that these vexed questions had at last been solved. In an effort to ascertain if possible the prevailing view of those best qualified to express an opinion a questionnaire was submitted to the following gentlemen: J. 0. Arnold Sir Robert Hadfield Edgar C. Bain W. H. Hatfield Carl Benedicks Samuel L. Hoyt N. Belaiew Kotaro Honda H. M. Boylston Zay Jeffries Harry Brearley H. Le Chatelier G. K. Burgess H. H. Lester William Campbell Francis F. Lucas H. C. H. Carpenter John A. Mathews Pierre Chevenard A. McCance P. Dejean Albert Portevin C. A. Edwards Walter Rosenhain F. Giolliti Bradley Stoughton G. Grenet F. C. Thompson Leon Guillet

Jan 1, 1926

By V. R. Garfias

Although the work on which this paper is based was carried on by the writer as Special Commissioner of the Petroleum Department of the Mexican Government, the opinions expressed are only his personal views for which the Mexican Government can in no way be held responsible. Notwithstanding that the appointment covers all phases of the so-called petroleum question, as the one question of immediate importance was that relating to taxation, it was decided to devote all the time to this phase of the work. The present report has been divided into two closely related parts, the first dealing with the production and marine transportation of Mcxican petroleum, and the second, with the Mexican taxation on petroleum and its products. The writer wishes to acknowledge the loyal cooperation rendered by Mr. M. C. Ehlen, who had charge of the statistical work, and by Miss S. Stern and Messrs. E. P. Heiles and J. E. Morrissey. The aim throughout the work has been to pave the way for a thorough understanding between the Mexican Government and the oil operators and to present a true and clear statement of facts relating to the questions at issue. Mexican Oil Fields Development The salient features in the development of the Mexican oil fields may be summarized as follows: 1901. First commercially productive well in Ebano field. 1902. Tehuantepee field came in; Diaz Government granted concession to Pearson & Son on practically all Federal lands along the Gulf of Mexico. 1907. First producing well in the Furbero field. 1908. Dos Bocas well caught fire, advertising tremendous productivity of Southern oil fields of Mexico.

Jan 1, 1921

K. T. Aust and J. W. Rutter (General Electric Research Laboratory)—We find it difficult to reconcile the activation energies determined by Gifkins with his general conclusion that "migration during both creep and grain growth can thus be treated on the basis of the same model" (that of Lucke and Detert). Gifkins finds the activation energy for grain boundary migration during creep to be 24.5 kcal per rnol and that for grain boundary migration during grain growth to be 7.5 kcal per mol. The calculation carried out by Gifkins of the activation energy for grain boundary migration during grain growth, using the Lucke and Detert model, gives a value of 20 to 24.5 kcal per mol, rather than his experimental value of 7.5 kcal per mol. The theory of Lucke and Detert was developed to account for the rates of migration of grain boundaries in the presence of impurities during grain growth. The theory does not take into account the effect on the boundary migration of another, simultaneous process such as creep deformation and would be expected, therefore, to be applicable only to migration during grain growth. The fact that Gifkins measured a different activation energy for boundary migration during grain growth (7.5 kcal per mol) from that during creep (24.5 kcal per mol), although the specimens were of the same composition, shows clearly that such an effect exists under his experimental conditions; the presence of a simultaneous creep deformation markedly affects the boundary migration process in comparison with what would be observed under the same conditions but without the creep deformation. The failure of McLean's equation (Eq. [4] of Gifkins' paper) to give a satisfactory dislocation density difference for boundary migration during creep is not surprising, since the activation energy which must be used in this equation refers only to the elementary atom transfer process of grain boundary migration. This activation energy value is approximately 6 kcal per mol for zone-refined lead, as determined in both the grain boundary migration experiments of Aust and Rutter31, 32 and the grain growth experiments of Bolling and Winegard.33 Using this activation energy value, McLean's equation gives reasonable agreement with observed migration rates for grain boundaries moving free of the influence of impurities.31, 32 The value of 24.5 kcal per mol is probably associated with the presence of impurity atoms, as Gifkins suggests. It should be noted, however, that this value was obtained using lead of only one composition and measurements at only two temperatures. The work of Aust and Rutter3"' on the effects of tin, silver, and gold on grain boundary migration in zone-refined lead in the temperature range from 320" to 200°C, as well as the work of Bolling and Winegard34 on the effect of silver and gold on grain growth in zone-refined lead, shows that the measured activation energy is markedly dependent upon the kind and amount of solute present. Gifkins' work does not permit evaluation of the effect of the 8 ppm of impurities other than oxygen present in his specimens. One incidental point: the symbols used to designate the experimental points of Fig. 6 appear to be in incorrect order in the figure caption. As the caption is printed, it would indicate that larger grain sizes were obtained after annealing at 47°C than at 100°C, which does not agree with the text (point M, p. 1019). Finally, it seems clear from Gifkins' results that any serious attempt to determine whether grain boundary migration and grain boundary sliding during creep occur with the same activation energy, as Gifkins suggests and McLean rejects, must take into account the effects of impurities on these two processes, Although the work of Weinberg35 indicated that adding small amounts of copper, iron and silicon to aluminum did not affect the grain boundary shear behavior, it should be noted that his starting material contained approximately 60 ppm of impurities. Gifkins' results indicate impurity effects at an impurity level of 8 ppm, suggesting strongly that the most significant impurity range to be investigated lies substantially below that value. R. C. Gifkins (author's reply) — As Drs. Aust and Rutter suggest, the results under discussion may have to be reinterpreted in the light of their own work on grain boundary migration, which was not available to me when the paper was written. Because of their work, Aust and Rutter attach more importance than I did to the activation energy for grain boundary migration during annealing (7.5 kcal per mol) obtained from a "direct" plot of log-rate against the reciprocal of absolute temperature. At the time it was obtained, this value seemed rather low, although it was similar to the value obtained by Bolling and Winegard.36 It was then, and still is, difficult to accept this value because of the low value of the index in the power law for grain growth, which seemed to indicate the influence of impurities. It was also concluded that the low value of the activation energy might have arisen from the manner of selecting rates of grain growth which were truly comparable at the two temperatures. There were many other indications in these experiments and those on recrystallization during creep3? that an impurity, probably oxygen, was of importance. The model for grain-boundary migration which Lucke and Detert had proposed was an obvious possibility and its use yielded an activation energy for boundary migration during annealing of 20 to 25 kcal per mol.

Jan 1, 1961

By Robert Henry Bradford

This investigation was undertaken at the suggestion of Prof. Henry M. Howe, of the Department of Metallurgy, Columbia University, who, in a letter to the author, dated October 23, 1900, wrote as follows, suggesting the subject of this dissertation : "The extraction of silver from copper mattes by either the Ziervogel or the Augustin process depends upon converting the silver into silver sulphate by means of the sulphuric anhydride evolved from the decomposition of ferrous sulphate and cupric sulphate, which are formed during the roasting operation itself from the iron and copper sulphides present. "It occurred to me, some time prior to the autumn of 1897, that these processes might be made much easier by adding to them, at the proper stage, ferrous or cupric sulphate, or both, in the form of green or blue vitriol. That is, instead of having to rely solely on our ability to generate these sulphates in this very delicate roasting operation, my idea was that we could add a small quantity of already-prepared sulphate at the proper state of roasting, viz., at or before the period when the solphatizing of the silver occurs. The comprehensive audit of the accounts of a mining company is extremely important in its relations to the legal situation and obligations of the corporation, the personal liability of the directors, and the interests of the investing public. A consideration of the subject as affecting the professional duties and fixing the responsibility of a mining engineer engaged in the expert examination of a mine or in charge of mining operations, is equally important, though this phase of the question is not often presented systematically.

Jan 1, 1903

By W. P. Haynes

The 1938 production for all of Rumania amounted to 48.984.200 bbl., as compared with 53.239.500 bbl. in 1937. which represents a drop of 4.255.300 bbl., or 8 per cent. Of the various fields. there are only two major increases in production—Baicoi-Tintea with 3.092.400 bbl. And

Jan 1, 1939

By W. P. Haynes

The 1938 production for all of Rumania amounted to 48.984.200 bbl., as compared with 53.239.500 bbl. in 1937. which represents a drop of 4.255.300 bbl., or 8 per cent. Of the various fields. there are only two major increases in production—Baicoi-Tintea with 3.092.400 bbl. And

Jan 1, 1939

By Walter A. English

CONTENTS PAGE Introduction. By WALTER A. ENGLISH 1 Theory of Seismic Reflection Prospecting. By WILLARD H. TRACY 2 Instruments for Reflection Seismograph Prospecting. By ARTHUR NOMANN 9 Seismograph Field Operations. By FRANK ITTNER 15 Determining Geologic Structure from Seismograph Records. By P. C. KELLY 22 INTRODUCTION BY WALTER A. ENGLISH,* MEMBER A.I.M.E. THE four papers making up this symposum have been prepared espe-cially for those who have no knowledge of seismograph prospecting. To many people mathematics is a formidable subject, and many are discouraged from studying seismograph prospecting under the mistaken assumption that the mathematical requirements are severe. In the papers presented here there is not a single mathematical equation. We believe that considerable competence in dealing with some of the most important problems of this work can be attained without any mathe-matical training whatever. At the present time, there is a real need for interpretation of results by persons thoroughly competent to bring geologic experience and imagination to bear on data that are subject to multiple interpretation from a strictly physical viewpoint. Likewise, those charged with the responsibility of planning seismo-graph exploration campaigns would do well to become familiar with as . much as possible of the technical aspects of the work. They would then be in better position to judge of its success in individual cases. It has often been said that the seismograph is a new structure-finding tool for the geologists to use. Using a tool and using its product are two different things. One does not use an automatic screw-threading machine when he buys a box of screws at the hardware store. Neither does the geologist

Jan 1, 1939

By Martin Mayers

IT has long been recognized that it would be highly desirable to be able to predict the temperatures at various points in a burning fuel bed and their variations with changes of the properties of the fuel and the rate of air supply. Experimental investigations of fuel-bed tempera-tures1-4 have not been lacking, but the absence of any theoretical back-ground has made it impossible to use the results of these tests as a basis for prediction, except in a very general way. A mathematical analysis5, based on a somewhat simplified theory of the distribution of heat in a, fuel bed, has recently been completed by the author. Even though numerical values of some of the coefficients are not. known, the calcula-tions result in some conclusions of general significance. Thus, for example, it appears that when the temperatures throughout the fuel bed can be calculated, the rate at which ignition of the fuel by underfeed action can be maintained can also be calculated. The uncertainty concerning the values of the coefficients referred to above is a serious limitation on the use of that method. The following paper presents a discussion of these coefficients and includes estimates of their values based on the data now available. A brief description of the theory on which the analysis is based, and some results of the calculations showing their degree of agreement with experimental results, are presented by way of introduction to the discussion of, the coefficients. For a more extended discussion of the theory, see the A.S.M.E. paper5.

Jan 1, 1937

By Duane E. Eubanks, David B. McDonald

The anticipated growth of western coal production over the next decade is expected to add approximately 274.3 million t/y (302.4 million stpy) to US capacity. The increased output, coming from both new mines and expansion of existing facilities, promises to bring with it a new set of problems for mine planners.

Jan 8, 1976

By C. E. Shoenfelt

There was very little oil activity in Utah in 1938. A few wildcat tests were drilled and the well at Cane Creek, started in 1937, was in active operation, but failed to reach its objective by the close of the year. The Clay Basin field in Daggett County, northeastern Utah, was extended about a mile east by the Mountain Fuel Supply Co. with the completion early in June of No. 3-D Murphy, NW. NW. SW. of sec. 23-3N-24 E. This well had an initial production of 16,000,000 Cu. ft. of gas a day under 2160 Ib. pressure, from Dakota sand at 5918 to 5925 ft. after plugging back from a total depth of 6035 feet. The Clay Basin field, in the few years it has been in operation, has developed into a gas field of major importance. Approximately 1300 acres has now been proved by development. Six wells are on production, five of which were completed in Dakota sand and the sixth in a sand in the Frontier formation. The field was connected to the Salt Lake line

Jan 1, 1939

By C. E. Shoenfelt

There was very little oil activity in Utah in 1938. A few wildcat tests were drilled and the well at Cane Creek, started in 1937, was in active operation, but failed to reach its objective by the close of the year. The Clay Basin field in Daggett County, northeastern Utah, was extended about a mile east by the Mountain Fuel Supply Co. with the completion early in June of No. 3-D Murphy, NW. NW. SW. of sec. 23-3N-24 E. This well had an initial production of 16,000,000 Cu. ft. of gas a day under 2160 Ib. pressure, from Dakota sand at 5918 to 5925 ft. after plugging back from a total depth of 6035 feet. The Clay Basin field, in the few years it has been in operation, has developed into a gas field of major importance. Approximately 1300 acres has now been proved by development. Six wells are on production, five of which were completed in Dakota sand and the sixth in a sand in the Frontier formation. The field was connected to the Salt Lake line

Jan 1, 1939

By Charles H. Eldridge, Robert J. Anderson

When a metal or alloy is poured into a mold, internal stresses are set up by the cont,raction in volume on passing from the liquid state at the temperature of pouring to the solid state at the ordinary temperature. It is assumed by the writers that all castings are internally stressed. That any casting is internally stressed is shown by its warping or distortion on maturing at the ordinary temperature, by warping or cracking on heating, or by cracking or distortion on machining. In the investigation made by the writers, the internal stresses in cast non-ferrous alloys were studied with a view to examining the effects of heat treatment (i.e., simple anneal) on the release of such stresses. Data have been obtained that show quantitatively that internal stresses can be removed by appropriate heat treatment. The investigation was limited to a study of the effect of heat treatment on stress release in cast rings of the 87:7:5:1 copper-tin-zinc-lead alloy. The writers are indebted to E. G. Fahlman for the method used for inducing stress in cast rings; to M. E. Boyd for microscopic examination and for other aid; and to G. B. Dalrymple for the chemical analyses. General Information While casting stresses have been discussed considerably, they have usually been treated in a general way, and so far as the writers know no measurements of the magnitude of internal stresses in castings have been reported. It has been suggested by many investigators, particularly in the case of steel castings, that castings are internally stressed, and that these stresses can be removed by annealing. In a casting, the internal

Jan 1, 1923