Search Documents

By M. Ahlers, Horace Pops

Slip features and formation of stress-induced mm-tensite have been studied in single crystals of fl phase Cu-Zn alloys in the composition range between 43 and 48 at. pct Zn. A phenomenological analysis is presented in which the glide planes and directions that me associated with the inhomogeneous shear in the martensite phase are predicted from the experimentally determined habit planes and macroscopic shear directions. It is shozun that the resolved shew component of the applied stress on the secondary shew system is a very important factor governing the formation of stress-induced martensite. A comparison is made between martensitic phases that form spontaneously upon cooling and those phases that arise from deformation. THE ß phase in Cu-Zn alloys is unstable and may transform spontaneously by a martensitic transformation1-3 during cooling. Thermoelastic and burst-type spontaneous martensitic phases have been observed3 in the composition range between 38 and 42 at. pct Zn. Martensite forms in alloys containing more than 42 at. pct Zn only by cold work below a temperature denoted as Md.4 Thus, alloys near the equiatomic composition can undergo a stress-induced transformation upon cold work at room temperature. Although data have been obtained concerning the effect of temperature5 and composition4 on the deformation of polycrystalline Cu-Zn alloys, it is rather surprising that few detailed studies6-8 on 6 brass have been conducted for single crystals where the stresses acting on crystallographic planes can be determined. A thorough understanding of transformation mechanisms requires knowledge of the role of stress and plastic strain. With this objective in mind we have made an investigation of the stress-induced rnartensite transformation in single crystals of 0 brass in the composition range between 43 and 48 at. pct Zn. Particular emphasis is given to the morphology and crystallographic features and a comparison is made between stress-induced and spontaneous martensite. I) EXPERIMENTAL PROCEDURE Master alloys having nominal zinc contents of 43, 45, and 48 at. pct were prepared from spectroscop-ically pure metals (>99.999 pct) in sealed quartz tubes under a partial pressure of helium. These alloys were cut into several pieces and converted into small rods by melting in quartz tubes. Subsequently, single crystals were grown from the rods by the Bridgman technique and homogenized for 3 hr at 820°C. Lattice parameter measurements were made from stress- relieved filings. Compositions, as determined from the reported variation of lattice parameter with atomic percent zinc,' indicated a zinc loss of less than approximately 0.25 at. pct. The single crystals were electroturned using a phosphoric acid electrolyte into tensile specimens each with a center section of 1 mm diam and 1 cm gage length. Cylindrical specimens approximately 3 mm in diam and 10 mm long and spark-machined rectangular blocks approximately 3 by 3 by 10 mm were prepared for compression studies. These blocks were stress-relieved and electropolished to eliminate any stresses introduced by spark machining. Crystal orientations were determined to an accuracy of ±2 deg primarily from back-reflection Laue photographs, and sometimes by the rotating single-crystal method. Figs. 1 to 3 show the location of the tension and compression axes within unit stereographic triangles. All specimens were deformed plastically at room temperature using an Instron machine, the crosshead speed being 0.02 or 0.05 cm per min. A hard steel hemisphere was placed at the upper end of the compression samples to achieve uniaxial loading. Trace normals of slip markings and habit planes of strain-induced martensite were determined to an accuracy of ±4 deg from the rectangular blocks by a two-surface analysis and from cylindrical specimens by measuring the angle between the tensile (or compression) axis and the tangent to the surface trace for different rotations about the deformation axis. Slip

Jan 1, 1969

By E. S. Greiner

THE hot working of chromium was first reported by Hunter and Jones; who used small pellets of the material obtained by the reduction of chromium chloride with sodium. Later, the working of chromium at 600° to 1100°C was reported by Marden and Rich,2 and at 1250°C by Kroll3 The hot rolled material3 had a Brinell hardness of about 150 (62.5 kg, 2.5 mm ball, 1 min) and was brittle at room temperature. Except for that associated with hardness indentations, no plastic flow in chromium at room temperature has been reported to the author's knowledge. Studies described here have shown slip markings in chromium after deformation at room temperature.

Jan 1, 1951

Launching Platform - Drift Indicator- Stratascope-are components of Carbide and Carbon Chemicals new Mining Machine No. 3.

Jan 1, 1953

By R. A. Burmeister, P. E. Greene

Two methods for the synthesis and growth of single crystals of B6 P are described: a solution-growth process employing nickel as the solvent, and a vapor-growth process employing BBr3 and pH3 as the reac-tants. Relevant portions of the Ni-B-P phase diagram have been examined and liquidus data are presented for an isobaric section at an equivalent P2 pressure of 3.8 Torr, and an isothertnal section at 1300°C. Solution-growth techniques are described and the purity and crystalline perfection of the resulting material is discussed. Epitaxial growth of BeP on &P substrates has been obtained using the vapor-phase system. Evidence is presented which supports the assignment of the stoichioknetry B6P to boron sub-plwsphide. THE B-P system differs from other III-V systems in that it contains two distinct compounds. The existence of the monophosphide (BP) has been known for some time,' whereas the subphosphide (B6P) was reported only recently.' Both of these compounds are large bandgap semiconductors (Eg = 2.0 ev for BP~ and 3.3 ev for B6P4), and are therefore of interest for optoelectronic applications. The crystal structure of B6P is quite different from those of most semiconductors, being derived from that of a-rhombohedral boron by the incorporation of the two phosphorus atoms in the intericosahedral sites of the a-boron unit cell?76 B6P also exhibits a number of unusual characteristics, including a high degree of chemical inertness, hardness, and high-temperature stability. No information concerning other physical properties is available in the literature. The present study is part of a broader investigation of the preparation and properties of B6P. This paper considers methods of growing single crystals of B6P of suitable size and quality for physical-property measurements. A detailed discussion of the electrical and optical properties of B6P will be given elsewhere.' GENERAL CONSIDERATIONS The method first used to synthesize B6P was the disproportionation of BP' according to the reaction The equilibrium P2 pressures corresponding to this reaction were also determined .'" It is therefore possible, in principle, to apply several of the reactions reported for the synthesis of BP to the synthesis of B6P merely by selecting lower phosphorus pressures or higher temperatures, in accordance with the equilibrium data. Other techniques for the direct synthesis of microcry stalline B8P have also been reported.1°

Jan 1, 1968

By C. C. McDermond, Others, B. N. Zavoico

Production of crude oil in Venezuela for the year 1937 was 186,653,-916 bbl., as compared with 155,228,982 bbl. produced in 1936, an increase of almost 31,500,000 bbl. The oil-field strike, which started on Dec. 14, 1936, lasted until Jan. 25, 1937, when a total of 10,000,000 bbl. of production was estimated to have been lost (5,750,000 bbl. in 1936 and the remainder in 1937). Of the total of 186,653,916 bbl. produced in 1937, the Lagunillas field contributed 45.6 per cent, a drop of approximately 10 per cent under 1936 figures; Tia Juana, 14.3 per cent; Quiriquire field, 14.0 per cent; La Rosa area, 13.3 per cent and the Mene Grande field, 7.6 per cent, these being the five leading contributors of the year's production. Detailed production figures by fields and by companies are shown on Table 1. Of the total production of Venezuela the following four major companies accounted for the greater proportion: Standard of Venezuela and Lago Petroleum Corporation together, 48.3 per cent; Shell, 37.4 per cent and Venezuela Gulf, 14.0 per cent. At the end of the year, 2491 wells were producing, of which number 1291 wells were pumpers, or about 52 per cent. Production The accompanying statistics of production record of Venezuela oil fields from its inception to Dec. 31, 1937, shown on Table 2, indicates that the cumulative production reached 1,503,283,228 bbl. In order of importance, Lagunillas leads all the fields, having accounted for about 50 per cent of Venezuelan production, followed by La Rosa area, which produced about 21 per cent; Mene Grande, which produced about 13 per cent, and Quiriquire, which produced 6.5 per cent. Table 3 shows the age of each field. Mene Grande is the oldest, having produced for 24 years; Tarra is next, 21 1/2 years old, and El Mene third, 171/2 years. The gravity of the crude from the various fields, also shown on Table 3, remained unchanged, the only addition being the new Tia Juana field, which averages 15.6' A.P.I. Table 4 shows the method of production by fields as of Jan. 1, 1938; at the end of the year 2491 wells were producing, compared with 2005 wells producing at the beginning of 1937, or an increase of 486 wells. The completions for the year reached 512. Of the 2491 wells producing crude oil, 1291 wells, or approximately 52 per cent, were pumping, 925 (approximately 37 per cent) were flowing naturally and 275 (11 per cent) were on

Jan 1, 1938

RECEIPTS [Magazine Advertising $ 62,564.83 Magazine Sales 3,591.44 Totalm 66,156.27 Dues, Arrears7,032.88 Dues. Current96,839.74 Dues, New Members6,525.00 Dues, in advance 1,907.02 Initiation Fees7,584.00. Sale of Transactions3,909.03 Sale of Binding7,845.05 Sale of Special Editions 338.20 Sale of Year Book76.20 Sale of Pamphlets1,189.06 Sale of Authors' Reprints867.54 Miscellaneous Receipts62.93 Interest on Bank Balances1,712.89 Interest on General Reserve Fund337.50 Interest on Life Membership Fund557.84 Interest on James Douglas Library Fund....5,491.89 Total Receipts$208,433.04] [ ]

Jan 1, 1925

Estimated Receipts Dues Arrears $ 3,500 00 Current 108,115 00 New Members - 11,937 00 In Advance 1,763 00 $125,315 00 Initiation Fees - 7,250 00 Initiation Fees-Additional if increased to $20 00 7,250 00 Sale of Transactions 3,000 00 Sale of Binding 7,092 00 Sale of Magazine 2,913 00 Sale of Pamphlets 370 00 Sale of Indexes and Emmons Vols 313 00 Sale of Pyrometry 900 00 Sale of Raymond Vol 100 00 Interest received on Bank Balance . 500 00 Interest received on Life Memberships 500 00 Advertising-Gross 27,000 00 Voluntary Subscriptions-Estimated 16,000 00 Income from James Douglas Fund 5,000 00 Total $203,503 00

Jan 1, 1923

Sept. 3-6, AIMS, Fall Meeting, Industrial Minerals, Minerals Beneficiation, Mining, Geology, & Geophysics, Iron and Steel, and Coal Div., Palmer House, Chicago. Sept. 3-13, AIMS, Chicago Section, Centennial of Engineering, Chicago. Sept. 5-6, Engineers' Connell for Professional Development, annual meeting, Hotel Sheraton, Chicago. Sept. 8-15, International Geologic Congress, Algiers. Sept. 11-13, American Institute of Chemical Engineers, Palmer House, Chicago, Ill. Sept. 18, RIME, Utah Section, Newhouse Hotel, Salt Lake City. Sept. 22-25, American Mining Congress, Metal and Nonmetallic Mining Convention and Exposition, public auditorium, Denver. Sept. 23-25, Institution of Mining and Metallurgy, symposium on mineral dressing, Royal School of Mines, London. Sept. 30, AIME, Morenci Sub-section, Longfellow Inn, Morenci, Ariz.

Jan 1, 1952

By Howard I. Smith

THE mineral trona was discovered on Government land in 1938, about 18 miles west of the town of Green River, Wyo., in the core of the John Hay, Jr., well, a test well drilled for oil by the Mountain Fuel Supply Co. in sec. 2, T. 18 N., R. 110 W., sixth principal meridian. Although no oil or gas was reported, the drilling led to a discovery of great potential economic importance and exceptional scientific interest. Trona is a relatively rare mineral found at various places in playa deposits but not previously found at any great depth. It is composed of hydrous sodium carbonate and sodium bicarbonate (Na2CO3.NaHCO3.2H20). Pure trona contains the equivalent of 70.35 per cent of sodium carbonate. Total sodium computed to carbonate times 1.42 equals the percentage of trona in the absence of other sodium carbonate minerals in the sample. ANALYSES Two short pieces of core sent to the author a few days after the completion of the Hay well were analyzed by R. C. Wells[t] and found to be exceptionally pure trona. A brief article on this discovery has already been published.1 Arrangements were then made through W. T. Nightengale[$] for the author to inspect and sample the core. The company log of the well included notations of sodium salt crystals from a depth of 1190 to 1820 ft. Not being able to identify all the minerals present, the author selected several specimens of the core for petrographic examinations and sampled the sections of trona for analysis. J. J. Fahey, of the Geological Survey, examined the specimens and reported most of the crystals to be a new anhydrous sodium carbonate and calcium carbonate mineral (Na2CO3.2CaCO3), which he named shortite,2 after Maxwell N. Short.* He analyzed the samples of trona, with the results shown in Table I. [ ] In addition to the 10 ft. I in. of trona in the first section, it is reasonable to assume that the 9 ft. 8 in. for which no core was available for sampling is either mostly trona or some other soluble salt, but it should not be included in calculating reserves. In the part of the core between 1590 ft. 3 in. and I600 ft. 4 in. the material insoluble in cold water, amounting to about 5 per cent, was estimated petrographically to contain 70 per cent clay, 25 per cent shortite, and 5 per cent pyrite. ACCOMPANYING MINERALS Fahey later secured about 600 ft. of the core for a detailed examination and study

Jan 1, 1942

By F. L. Wolf

THE tests here described were made to obtain information regarding costs, efficiency, etc. of baking cores in an oil-fired oven, and two electric ovens, which were installed, early in 1920, in the core room of The Ohio Brass Co. and were used almost continuously during the rest of that year. Operating costs were rather high so a complete test was undertaken early in 1921. The ovens will be referred to as Nos. 1, 2, and 3. Nos. 1 and 2 are electric ovens of different makes while No. 3 is an oil-fired oven made by the firm that made No. 2. The three are equipped with similar ventilating devices. They have full-height doors at front and rear. The cores are placed on iron racks, which are lifted by Cowan trucks and rolled into the ovens through the front doors. When baked, they are removed through the rear doors. Fig. 1 shows the general plan of the electric ovens while Fig. 2 shows the plan of the oil-fired oven. Oven No. 1 is 91 in. (231 cm.) wide, 83 in. (210 cm.) high, and 79 in. (200 cm.) deep, inside measurements. The walls are constructed in, panels about 18 in. (46 cm.) wide and 4 3/16 in. (10.6 cm.) thick, packed with blocks of insulating material and covered with sheet iron. The concrete floor on which the ovens set is 13 in. (33 cm:) thick. A recess about 5 in. (13 cm.) deep was cut in the floor to provide room for the heating units. Channels and plates supported. on I beams serve as' supports for the trucks and racks. The ventilating system consists of a Sirroco No. 1 ½ fan, connected so as to draw air from the top of the-oven or from the room, through damper C, and to deliver it either to the bottom of the oven or to the floor; the delivery is controlled by the vane A. The fan and pipes are covered with ¼ n. (6.3 mm.) asbestos cement lagging.

Jan 4, 1922

By I. N. Knapp

Introduction.-The special object of these notes is to describe the mixing, testing, and use of mud-ladened water for rotary drilling in such a way as to make them helpful to the driller, the operator, or the engineer in solving his own special drilling problems. The structures, apparatus and tools used are indicated in a general way. No attempt is made to describe the art of rotary drilling; only such description as are necessary to make plain the use of mud are given. The information is the result of actual experience in drilling in Coastal Plain formations. The materials encountered in the wells drilled were unconsolidated sands, gravels, and clays, in which thin layers of sandstones, shell conglomerates, and shales began to appear at about 1,200 ft. in depth, although one well was drilled to 3,018 ft. without encountering any cemented or indurated materials. Unusual Conditions.-The general surface of the ground where the drilling was done being hardly a foot above mean tide, and the daily tidal variation being about 15 in., it was found necessary to plank over the sod surface with 3-in. plank to work from. A 30 by 30 ft. planked area was sufficient to carry the derrick with equipment and 2,500 ft. of 4-in. drill pipe stacked in it. The derrick was set up 3 ft. on cribbed blocking arranged to spread the load over the planking. The engine, boilers, and pipe yard were also carried on 3-in. planking. Drilling Outfit.-This consisted of a derrick, 20 by 20 ft. and 84 ft. high, two 35 h.p., "oil country" boilers, one double 8 ¼ by 10 in. reversible engine, two 10 by 6 by 12 in. duplex mud pumps, one 15-in. rotary, "hoisting works" with chain drive, hoisting block with line, crown block with pulleys, rotary' jetting swivels, hose, complement of tools, pipes and connections, and. a mud mixer, with engine.

Jan 12, 1914

By A. S. Joy

Vacuum flotation tests carried out according to the method of Schuhmann and Prakash1 have shown that the acid limiting edge of the flotation area for a Brazilian hematite, in the presence of dodecylamine, is a straight line of slope approximately unity. The flotation tests and the structure, surface ionization, and electrokinetic properties of this hematite have been fully discussed elsewhere. 2 The numbers of adsorbed H+, and OH- ions and collector molecules have been determined in the range of critical conditions defining the acid limit of the flotation area. The total amine adsorption is shown in Fig. 1 as a set of contours superimposed on the straight part of the flotation area. These were determined by spectro-photometric estimation of the complex formed between residual amine and the anionic dye Orange II.3 The ionic strength of the solutions was kept constant and at a value in sufficient excess of the amine concentration to ensure that the diffuse part of the double layer was populated predominantly by indifferent ions. Adsorption of H+ and OH- in the absence of amine was found by potentiometric acid-base titration in the presence of hematite.4 The form of the adsorption-titration curves suggested that the hematite surface behaves in an amphoteric manner, and that positively charged sites arise through loss of a hydroxyl ion, and negatively charged sites by loss of a hydrogen ion. On this basis, curves 8 and 9, shown in Fig. 2, were calculated from the titration curves. These show the variation of the numbers of positive (s +) and negative (s—) sites with pH. To distinguish between ionic and other modes of adsorption, zeta-potential determinations have also been made using the streaming potential technique. The influence of amine on the zeta-potential of the mineral over a wide pH range is shown in Fig. 3. The change in charge ?s, due to adsorption of amine ions in the Stern layer, was calculated by applying the Gouy-Chapman theory, as modified by Stem, to the results shown in Fig. 3. The validity of this treatment has been shown by Ottewill and Jaycock.5 The three full lines, Nos. (1) through (3), included in Fig. 2 show the relationship between ?s and pH at three amine concentrations. The general conclusion from the zeta-potential curves is that adsorption of amine causes a reduction in the negative charge on the surface. Comparison of the values shown in curves (1) through (3) of Fig. 2 with the - curve shows that the magnitude of the reduction is comparable with that of s - at any given

Jan 1, 1964

By David Segura

THE Huitzuco mercury deposits have been described by C. W. Vaupell,1 therefore the general information such as location, history, production, etc. will not be repeated here. The present owners acquired the property when the deep levels of the Cruz mine were flooded, and it was believed that a relatively large tonnage of low-grade ore and fills would be encountered in the flooded section, because of the early mining methods used in the Cruz mine. The mine was partly unwatered and about 187,000 tons of fills was pit-sampled in the San Cayetano stope. These fills average 2.4 kg. Hg per ton. During the period of maximum production at Huitzuco, the ores were sorted in the mine and cobbed into 3-in. pieces, which were treated in Scott furnaces. Large pieces of raw ore are found in the sinter, and it is indicated that both recovery and costs were not very satisfactory. Recent practice has been to treat the ores in closed retorts made of 10-in. pipes. Because of the presence of combined antimony in the mineral livingstonite (HgS.2Sb2S3) and considerable native sulphur, little or no metallic mercury is recovered in the condensers and a second retorting of the condenser muds is necessary. This makes the treatment of the ores expensive and tends to low recoveries of mercury. The principal costs of retorting are, in their relative order: (1) fuel, (2) low recovery of mercury, (3) replacement of retort pipes, (4) labor. METHODS TESTED Three series of experiments have been made, with the object of reducing the costs of recovering mercury and antimony from the ores, by: (1) wet metallurgical methods, (2) bulk roasting in large mechanical furnaces, (3) concentration to reduce the bulk to be followed by roasting in some mechanical furnace. The wet metallurgical methods did not appear feasible because of the high cost of the alkaline solvents used, and investigations of these were not carried beyond the preliminary stage.

Jan 1, 1938

By Arthur Knapp

Oil-well depletion curves, to be of value, should show when a well or lease may no longer be operated at a profit. The difference, at any time, between the total expenditures and the total income of a lease or well may be called the lease status. Plotting this lease status against time will give a curve subject to more accurate and different interpretations than the barrels-time curves. According to the hypothetical barrels-time curves shown in Fig. 1, well A, at the end of 16 mo., is producing twice as much oil as well B and will continue to produce for another year whereas well B will cease producing in about 6 months. Data fob Lease Status-time or Dollars-timb Curve Time Lease Months Status Lease purchased for $3000.............................. 0 — $ 3,000 No expenses chargeable to lease for 3 mo................. 2 — 3,000 Well A is started; cost of drilling for month is $16,000..... 3 — 19,000 Well is completed at additional cost of $10,000............ 4 - 29,000 Well A is brought in and flows 10,000 bbl. first month (we Fig. 1). Necessary to invest in tanks, boilers, pipe lines, etc.; difference between expenditures and receipts gives profit for month of $5,000............................ 5 — 24,000 Investment is small, cost of operating well A is small, so profits are $15,000................................... 6 — 9,000 Well ceases to flow so there is additional investment for pumping equipment and additional operating expense; net earnings from 6,000 bbl. of oil produced is $4,000. 7 ... Lease operation nor becomes normal and curve becomes smooth........................................... 8 — 500 9 2,000 10 4,500 11 6,000 12 7,700 13 8,700 14 9,000 15 9,500 16 10,000 A hypothetical lease status-time, or dollars-time, curve of this lease is shown in Fig. 2. At zero time, the lease is purchased for $3000, which is plotted below the zero dollar line, All subsequent entries are plotted

Jan 1, 1921

By H. S. Jerabek, Charles S. Barrett, Robert F. Mehl

The precipitation of the nitride Fe4N from the solid solution of nitrogen in a Fe and of the phosphide Fe3P from the solid solution of phosphorus in a Fe both lead to the formation of structures that may be easily identified as Widmanstatten figures, within the meaning of the term as used in this series of papers. A complete solution has been obtained for the figure formed by Fe4N. The structure of Fe3P, however, is not fully known and a complete solution of this figure thus cannot be obtained; nevertheless, a study of this figure has furnished some new information. Precipitation of Fe4N from Alpha Solid Solution of N in Alpha Fe Constitution of System Iron-nitrogen A knowledge of the constitution of the whole of the Fe-N system is unnecessary for this work, though the recent studies by Eisenhut and Kauppl and by Lehrerz have clarified most of the moot points; it is sufficient for our purpose to state that a Fe of high purity dissolves 0.42 per cent of nitrogen in solid solution at the eutectoid temperature, 591' C., and that this solubility decreases at first rapidly and then more slowly until at room temperature the solid solubility amounts to approximately 0.1 per cent nitrogen.3

Jan 1, 1934

By R. C. Davis, R. F. Berry, G. W. White, B. T. O’Connell, L. A. Stacha

P,, and v, may now be solved for by trial and error between Eqs. 2 and 3, by assuming time approaching zero and equating PI, to P12. Observe that the pressure under the slug, P12 of Eq. 3, does not remain equal to the P1, at the valve in Eq. 2 as the slug proceeds up the hole. To plot the profile of pressure vs depth, it is necessary to express P12 in terms of P11. To do so, the extent to which the original submergence length S changes with respect to time must be analyzed. At the end of time t after injection, the actual value of L in Fig. 3 is The fall-back v,(t) is now distributed in the gas and exerts pressure on the bottom. This, in addition to the weight of the gas, amounts to the difference in pressures from point to point. With the average pressure profile calculable, a true numerical value for the average pressure in the tubing may be obtained. The value of v, must be obtained experimentally, and since v,, S and D are known, the basic Eq. 1 may be solved for the amount produced. Knowing P, and the actual volume of tubing occupied by gas (vat), it is possible to calculate the volume of gas at standard conditions which is present in the

By Peter J. Conroy, Julianne H. Gyarmaty

INTRODUCTION The current study is part of the U.S. Department of Energy's (DOE) on-going subsidence research program. The long-term objective of the DOE program is to develop analytical methods of subsidence prediction applicable over a broad range of geologic and mining conditions encountered in the United States. The DOE currently has several contracts in progress to develop a sound data base that can be used in the development of predictive models. Dames & Moore is currently under contract to DOE to collect and analyze detailed subsidence and hydrologic data from a coal mine employing longwall mining methods in the Eastern Coal Province. Work under Contract No. DE-AC22-80PC 30335 began in October of 1980 and will continue through September of 1984. The contract includes monitoring of two adjacent longwall panels. This paper summarizes the surface monitoring work that was performed through February of 1982. Mining of the first of the two panels (3 off 3 north) was completed on February 3, 1982. Results of the surface monitoring through completion of this panel are presented and discussed. SITE DESCRIPTION The mine being studied is located in eastern Ohio. The site is west of the Ohio River, approximately 56 km (35 miles) south of Wheeling, West Virginia. The topography of the unglaciated region

Jan 1, 1982

By Theodore Nagel

Fuel-oil, natural gas and coke oven gas, producing the higher temperatures of open-hearth current practice, have been gradually displacing producer gas the lowest cost fuel for open hearth operations. The lower temperatures of combustion products from producer gas is caused by nitrogen dilution. Practical Application of Combustion Thermochemistry One pound of carbon burned to CO produces 3,960 B.T.U. and one pound of carbon burned to C02 produces 14,140 B.T.U. The second unit of oxygen uniting-with gasified car-bon (-CO) produces (14,140 - 3,960) 10,180 B.T.U. which is;(10,180 - 3,960) 6,220 B.T.U. more heat than produced by the first, unit of oxygen forming CO by uniting with solid carbon. A review of the relative combustion heating values of commercial gaseous fuels reveals CO requires a minimum of air for combustion, and because of minimum nitrogen dilution and the high thermal release from CO higher temperature combustion products are produced from CO than from natural gas or from coke-oven gas under similar combustion conditions. Inert nitrogen diluent lowers the calorific value of fuel gas and its diluting effect is cumulative in lowering the temperature of the products of total, combustion. It is not only logical but, practical in partial combustion, converting bituminous coal to gas, to generate the gas, with reduced nitrogen dilution.

Jan 1, 1936

Meeting of Oct. 23, 1914.-It was voted to take no action concerning the proposed amendments to Article VIII, Sections 2 and 3, but that they be sent to the membership, as provided by the Constitution, together with a statement of the arguments for and against the proposed changes. It was voted that the following proposed amendment, which had been unanimously approved at the annual meeting of the Institute on Feb. 18, 1914, be sent to the membership as provided by the Constitution, together with the approval of the Board of Directors of this change: Article III, Section 1, paragraph 3, sentences 2 and 3: substitute the following: "Any Member, Junior Member or Associate in arrears for two years shall be dropped from the rolls unless the time for payment is extended by the Directors. A Member so dropped may be reinstated by the Directors on paying the arrears of clues and other indebtedness with which he was charged on the books of the Institute it the time he was dropped. A Member or Associate thus reinstated shall receive the Transactions for the back year for which he pays." It was unanimously voted to extend the sincere thanks of the institute to Samuel A. Taylor, Chairman, and to each member of the several Committees of the Pittsburgh meeting, for the enjoyable and successful meeting which they brought about.

Jan 12, 1914

By Theodore Nagel

Fuel-oil, natural gas and coke oven gas, producing the higher temperatures of open-hearth current practice, have been gradually displacing producer gas the lowest cost fuel for open hearth operations. The lower temperatures of combusts on products from producer gas is caused by nitrogen dilution. Practical Application of Combustion Thermochemistry One pound of carbon burned to CO produces 3,960 B.T.U. and one pound of carbon burned to C02 produces 14,140 B.T.U. The second unit of oxygen uniting with gasified carbon (CO) produces (14,140 - 3,960) 10,180 B.T.U. which is (10,180 - 3,960) 6,220 B.T.U. more heat than produced by the first unit of oxygen forming CO by uniting with solid carbon. A review of the relative combustion heating values of commercial gaseous fuels reveals CO requires a minimum of air for combustion and because of minimum nitrogen dilution and the high thermal release from CO higher temperature combustion products are produced from CO than from natural gas or from coke-oven gas under similar combustion conditions. Inert nitrogen diluent lowers the calorific value of fuel gas and its diluting effect is cumulative in lowering the temperature of the products of total combustion. It is not only logical but practical in partial combustion, converting bituminous coal to gas, to generate the gas with reduced nitrogen dilution.

Jan 1, 1936