Search Documents

By Charles H. Thurman

THE data given herein were first included in a paper read before San Francisco Section, A.I.M.E., in October 1940, and are applicable to conditions existing until the gold-dredging industry was temporarily suspended by Order L-208 of the War Production Board in the fall of 1942. There is no doubt that gold dredging will be resumed at some future time, and on a scale equivalent to that of the recent past, but the cost data given herein will be affected to some extent by conditions existing at that time, and by labor rates and prices for materials then prevailing. DRAGLINE VS. BUCKET-LINE Dragline dredges should not be considered for mining large areas of low-grade placer gravel. In such deposits a dragline operator with a 5-cu. yd. dragline would be doing well to maintain an operating cost of 6¢ per cu. yd., while a bucket-line dredge with buckets no smaller than 7 cu. ft. each could be operated for less than 4¢ per cu. yd. By operating costs, I mean only field charges such as direct operating and overhead, which includes pay roll, power or fuel, repairs and maintenance, insurance, land clearing and general expenses, but not including such items as prospecting, depletion, depreciation of equipment, State Franchise Tax, or Federal Income Tax. It is not to be inferred that a dragline dredge cannot make a profit in small low-grade deposits, where the extent of a given property is too small to justify the use of the more costly bucket-line dredge. Consider small deposits of 10¢ gravel. It is obvious that a deposit of 5,000,000 cu. yd. of such gravel could not be mined profitably with a new, 7-cu. ft. bucket-line dredge, costing upward of $250,000, and with operation costs at 4¢ per cu. yd., paying for land or royalties out of earnings; nor could a new combination 5-cu. yd. dragline and washing plant, worth upward of $125,000 and working at 6¢ per cu. yd., make a profit. These comparisons are made because the hourly capacity of both types of dredges is nearly the same. The bucket-line dredge averages 93 per cent operating time in 24 hr., as against about 80 per cent or less for the dragline dredge. These percentages of operating time are important factors in making a comparison of this kind. The bucket-line dredge has greater efficiency in cleaning soft bedrock, usually characteristic of dredging deposits, and a 7-cu. ft. bucket-line dredge can be efficient to a total digging depth of 80 ft. (65 ft. below water, 15 ft. above). A 5-cu. yd. dragline dredge is limited to about 30 ft. of efficient digging depth, 5 ft. of which could be above water. In small areas of gravel not over 30 ft. deep, a 5-cu. yd. dragline dredge could make a profit where a bucket-line dredge could not do so. As an example: compare the dredging of 3,000,000 cu. yd. of 10¢ gravel 28 ft. deep with bucket line, costing 4¢ per cu. yd., and with a 5-cu. yd. dragline dredge operating at 6¢ per cu. yd. Because of small yardage, new equipment is not warranted, therefore we can assume that the dredges of both types are used equipment, fully depreciated. Dismantling, mov-

Jan 1, 1945

By H. C. Chang, N. J. Grant

Creep of very coarse grained, high purity aluminum was studied at 400° to 1100°F with an initial stress range of 50 to 1200 psi. The process of boundary sliding and migration was studied. The driving force of boundary migration under creep conditions is shown to be a combination of strain energy migrationand surface energy. A theory is presented regarding the strainenergyrole the grain boundaries play under creep conditions. From this thetheory intercrystalline failure of commercial alloys can be explained. Also from this theory an optimum grain size should exist for good high temperature properties of high purity materials. IN the investigation of the creep of very coarse grained, high purity aluminum previously reported,' the cyclic nature of the process of grain boundary sliding and migration has been established by microscopic observation of the actual creep process as well as metallographically. It was also substantiated by measuring localized strains across the grain boundaries. In addition, it was shown how extensive subgrain and fold formation may result from boundary sliding and how the slid grain boundary may become sharply wavy as a result of subgrain formation. Since the publication of those results, additional information on the process of grain boundary sliding and migration has been obtained. It is the purpose of this paper to report on the direction and driving force of boundary sliding and migration, the effect of grain size, and the effect of temperature. Finally the effect of decreasing purity (alloys 2s and 3s) on the process of boundary sliding and migration is noted. From these results, an explanation is presented for the intercrystalline failure of alloys under creep conditions. The effects of grain size on the creep properties of impure and high purity materials are discussed in the same light. The experimental procedures and technique have been presented elsewhere.' It is only necessary to state how the 2s and 3s aluminum specimens are prepared. Machined specimens were first annealed at 600°F for about 12 hr. In order to produce a large grain size the specimens were then stretched 3 to 8 pct. The specimens were marked with reference marks, electropolished, annealed at 900°F for 24 hr and at 1150°F for 12 hr, and repolished. The grain size of 2s aluminum produced by this treatment is comparable to that of high purity aluminum in the direction of its width of the specimen, i.e., there are 2 to 4 grains across the width of the specimen. However, the grains of 2s aluminum are 3 to 10 times longer in the direction of the specimen axis. On the other hand, the grain size of coarse grained 3s aluminum ranges from 10 to 20 grains across the width of the specimen due to the treatment just outlined and therefore is much smaller than that of both high purity and 2s aluminum. As in 2s aluminum, the grains are about 3 to 10 times longer in the direction of the specimen axis than in the direction of the width of the specimen. The arrangements of the grains in 2s and 3s aluminum were generally irregular; therefore it was difficult to follow the course of the grain boundaries. Results Method of Presentation: In order to show the arrangement of the grains, especially the direction and positions of the grain boundaries, traces of the grain boundaries on the four surfaces of the specimens were unfolded and mapped out after macroetching. Figs. 1 and 2 show the structural development drawings of specimens P-3 and P-8 respectively. The two flat surfaces (of which the front one faces the microscope) and the round-edged surfaces will be called the "front surface" and "back surface" and

Jan 1, 1954

By H. A. Shaw, H. G. G. Whitton

This paper describes the use of the electric-arc furnace for the production of tough-pitch, horizontal cast copper shapes and the production of copper anodes from tank house anode scrap. This installation is the only one of its kind in the United States. SINCE the initial use of electric-arc furnaces for refined copper melting on a commercial scale at Copper Cliff in 1936, this type of melting has been of extreme interest to everyone in any way connected with copper casting and fabricating. Early in 1948, Kennecott Copper Corp. decided to build an electrolytic copper refinery at Garfield, Utah. One of the major decisions to be made at that time was the type of furnace to be used for melting cathodes for casting into refined copper shapes and for melting anode scrap for the production of anodes. Based on the results obtained from arc furnaces by the Tnternational Nickel Co. of Canada, at Copper Cliff, and by the American Smelting and Refining Co., at Baltimore, coupled with certain important economic factors such as having an adequate amount of relatively cheap power available at the Magna Central Power Plant, high cost of poles and oil in the Salt Lake District, and the lack of natural gas at that time, the final decision was to install electric-arc furnaces rather than the standard type of rever-beratory furnaces. Experience has shown certain parts of the original installation to have been inadequate or in need of modification. Although the present status of arc-furnace melting at the Utah Refinery is far from perfect, nevertheless substantial progress has been made. At the Utah refinery, copper is melted in three 15-ft diam, size "M" Lectromelt furnaces, two of which are used for melting cathodes and one for remelting anode scrap. Each furnace is energized from a 13,800-225 v, 3-phase, 60-cycle, 6000-kva (at 40°C rise) oil-immersed water-cooled transformer. Auxiliary equipment for each refined copper furnace includes a charging machine, launders, ladle, 40 ft diam Walker-type casting wheel, bosh, and inspection conveyor. The anode furnace differs in that it is charged by hand from an elevated platform and the anodes are picked off the 24-ft diam casting wheel by a takeoff hoist and loaded directly into specially designed trailers, Figs. 1 and 2. Electrical Equipment Electric power to operate the arc furnaces is generated at the Kennecott-owned Magna Central Power Station two miles distant and transmitted to the Refinery outdoor substation at 44,000 v. At this point it is stepped down to 13,800 v and carried through concrete-lined underground tunnels to the switchgear and then to the primary side of the furnace transformers. The power is conducted from the Y-connected secondary bus bars of the transformer to the electrode arms by means of 22 flexible copper cable conductors per phase. Each cable has a cross-sectional area of 1,750,000 circular mils, giving a total area of 38,500,000 circular mils per phase. The power is carried from these cables to the three individual electrode holders by means of water-cooled copper bus tubing. The electrode clamps are incorporated in the electrode holders and are released by air pressure working against a spring in the clamp control cylinder. The movement of the electrode arms is either automatic or manual. The automatic control is used during melting and is regulated by three Westing-

Jan 1, 1954

Engineering Experiment Station, University of Arkansas, Fayetteville, Ark. W N Gladson, Dean and Director The Engineering Experiment Station has published a number of bulletins, only a few of which are of particular interest in this directory: Bulletin 3, Arkansas coal or oil for domestic heating; 4, Road materials of Arkansas, 5, A study of Arkansas coals, 6, Portland cement materials in Arkansas; 11, Natural gas versus Arkansas coal for house heating. Circular 3, Short cuts to combustion efficiency with natural gas Address the Engineering Experiment Station for any of these publications.

Jan 1, 1933

By William H. Spice

For the year 1943, exploratory drilling in South Central Texas continued on the sharp decline that started during 1942. Of the 3 counties comprising this district, as now revised to include the same area as is covered by District No. I, Oil and Gas Division, Railroad Commission of Texas, I5 counties are producing oil or gas. Only 29 exploratory wells were drilled during 1943, as compared with 51 exploratory wells in 1942, or a decrease of over 40 per cent. One new oil field and one new gas field were discovered during the year and a new horizon was discovered in an existing oil field. This cornpares with two new oil fields and an extension to an existing gas field in 1942. The one new oil field, South Washburn, in southeastern La Salle County, was discovered by Quintana Petroleum Corporation's No. I-D South Texas indicate in April 1943, flowing 4 bbl. per day, 48" A.P.I. gravity oil with an estimated 4 million cubic feet of gas from Wilcox sand at 6030 ft. This well i's the result of an extensive seismograph survey of the area. It is about 434 miles southwest of the same company's Green Branch field and by the end of the year one dry hole had been drilled to the southwest of this discovery. The one new gas field, which was not named, was located in eastern McMullen County by Edwin M. Jones' No. 102 Ezzell, in November 1943, for an estimated 8 million cubic feet of gas from shallow Jackson sand at 1222 ft. NO addi- tional wells have been drilled in this area, which may also be considered as an extension to the South Calliham field. The one new producing horizon was discovered in the South Campana field in southeastern McMullen County, by Argo Oil Corporation's No. 2-G Edrington, in January 1943, flowing 55 bbl. per day, 21' A.P.I. gravity oil with 40 per cent water from Government wells sand at 2609 feet. None of these discoveries were of major importance and subsequent development in these new areas has proved to be disappointing. Produc'tion for the district during 1943 totaled approximately 6,985,000 bbl. from about 3430 producing wells. This is an increase in production of about 5 per cent over 1942, but a decrease in producing wells of about 10 per cent under the number of wells producing in 1942 for the same district. Average production per well was 5.4 bbl. during 1943 as against 4.8 bbl. during 1942. Approximately 5,320,000 hhl. of this total production, or 76 per cent, was produced by the four Edwards lime fields, Luling, Branyon, Salt Flat, and Darst Creek, which are from 22 to 14 years old. The remaining production came from the 43 other active oil fields in the district. Drilling in the proven fields maintained approximately the same level as for 1942, with a total of 36 wells drilled. Of these operations, 21 were oil wells, one was a gas well and 14 were dry holes. This is a slightly better proportion of producers than for 1942. Washburn field had the greatest number of new producing wells drilled during the year, with a total of 10.

Jan 1, 1944

By William H. Spice

For the year 1943, exploratory drilling in South Central Texas continued on the sharp decline that started during 1942. Of the 3 counties comprising this district, as now revised to include the same area as is covered by District No. I, Oil and Gas Division, Railroad Commission of Texas, I5 counties are producing oil or gas. Only 29 exploratory wells were drilled during 1943, as compared with 51 exploratory wells in 1942, or a decrease of over 40 per cent. One new oil field and one new gas field were discovered during the year and a new horizon was discovered in an existing oil field. This cornpares with two new oil fields and an extension to an existing gas field in 1942. The one new oil field, South Washburn, in southeastern La Salle County, was discovered by Quintana Petroleum Corporation's No. I-D South Texas indicate in April 1943, flowing 4 bbl. per day, 48" A.P.I. gravity oil with an estimated 4 million cubic feet of gas from Wilcox sand at 6030 ft. This well i's the result of an extensive seismograph survey of the area. It is about 434 miles southwest of the same company's Green Branch field and by the end of the year one dry hole had been drilled to the southwest of this discovery. The one new gas field, which was not named, was located in eastern McMullen County by Edwin M. Jones' No. 102 Ezzell, in November 1943, for an estimated 8 million cubic feet of gas from shallow Jackson sand at 1222 ft. NO addi- tional wells have been drilled in this area, which may also be considered as an extension to the South Calliham field. The one new producing horizon was discovered in the South Campana field in southeastern McMullen County, by Argo Oil Corporation's No. 2-G Edrington, in January 1943, flowing 55 bbl. per day, 21' A.P.I. gravity oil with 40 per cent water from Government wells sand at 2609 feet. None of these discoveries were of major importance and subsequent development in these new areas has proved to be disappointing. Produc'tion for the district during 1943 totaled approximately 6,985,000 bbl. from about 3430 producing wells. This is an increase in production of about 5 per cent over 1942, but a decrease in producing wells of about 10 per cent under the number of wells producing in 1942 for the same district. Average production per well was 5.4 bbl. during 1943 as against 4.8 bbl. during 1942. Approximately 5,320,000 hhl. of this total production, or 76 per cent, was produced by the four Edwards lime fields, Luling, Branyon, Salt Flat, and Darst Creek, which are from 22 to 14 years old. The remaining production came from the 43 other active oil fields in the district. Drilling in the proven fields maintained approximately the same level as for 1942, with a total of 36 wells drilled. Of these operations, 21 were oil wells, one was a gas well and 14 were dry holes. This is a slightly better proportion of producers than for 1942. Washburn field had the greatest number of new producing wells drilled during the year, with a total of 10.

Jan 1, 1944

By Tilden Cummings

The extractive mineral industries share a number of common characteristics and basic problems which are completely different from those associated with manufacturing and mercantile operations. These industries now supply about 95% of the inanimate energy consumed in this country, and share with agriculture in providing virtually all of our basic raw materials. Mineral producers, like farmers, are subject to the economic hazards of fluctuating markets and prices. Unlike farmers, however, they cannot renew the productivity of the earth, but must seek continually for new sources of supply. The necessity for exploration and development of new reserves, to replace those used up by production, introduces additional factors of economic risk. These operations require the expenditure of large amounts of capital, often well in advance of any assurance of profitability. Commercial banks that understand these special problems can provide a variety of constructive financial services to the mineral industries. The history of cooperation between banks and mining enterprises has yet to be written, but there is every indication that it would encompass a period of hundreds of years. Records refer to depository and lending services by the early European private bankers involving precious metals and jewels. Many of the exploratory voyages to the Far East and the New World were organized with the financial backing of wealthy syndicates, some of which also provided banking services, in the hope of finding new sources of gold and other precious minerals. In the United States many large banks are closely identified with the development of some of the larger mineral deposits such as the Mesabi Range and the gold fields of California.

Jan 5, 1965

By C. W. Robinson

Transportation is the minerals business. Once upon a time the geologist, the engineer and later the metallurgist reigned supreme, but the leading role in mineral development today is the economist-especially the transportation economist. Obviously this trend is more important for large volume, low value mine-to-market movements of such commodities as iron ore, phosphate, potash, coal and petroleum. But, transportation is of sufficient importance to all mining activities to be included in forward planning. Civilization has been influenced by transportation developments to an extent little understood or appreciated. Although industrialists are capable of intelligent historical analysis of this phenomenon, too frequently they have failed to project, or anticipate those changes in transportation techniques which will influence the pattern of industrial growth.

Jan 1, 1971

By R. P. Thomas

Secondary fertilizer minerals are the mineral materials used to supply directly and indirectly the secondary and trace plant food nutrient needs of a fertilizer. Since few soils contain sufficient availability of all plant nutrients for their proper growth, man has prepared mixtures of plant food materials to correct these nutrient deficiencies. These mixtures or fertilizers, when added correctly to a soil, make it possible for abundant and economic crop growth. Many kinds of materials are used as sources of these needed nutrients. They come from natural and synthetic materials and minerals including many beneficiated byproduct compounds. A fertilizer consists largely of carriers of one or more of the three major plant foods, namely nitrogen (N), phosphorus-phosphorus pentoxide (P2O5) and potassium-potash (K2O). Many other nutrients are just as essential for plant growth as the three major plant foods. In fact, the efficient use of fertilizers today depends upon an adequate supply of all these other nutrients. Since these additional materials are usually removed from the soil by plants and supplied in fertilizer in less quantities than the major nutrients, they are called secondary and minor nutrients. In the early days these special nutrients were contained as impurities in the primary nutrient carriers. Today, fertilizers are made primarily from concentrated and synthetic materials which carry very few of these other essential nutrients. Consequently, many secondary and trace nutrient carriers, as salts, byproduct compounds and even minerals have to be added to fertilizers. Secondary Nutrient Carriers The secondary plant foods in fertilizer are next to the major nutrients in abundance. They are calcium, magnesium, sulfur, chlorine, silicon and sodium. Although many of these elements are added to a fertilizer as part of the major nutrient carriers, they are also added in special carriers. The large tonnage of these secondary nutrient carriers used in fertilizers represents only a small percentage of the total production of these materials. A fertilizer producer thinks in terms of materials which supply nutrients instead of minerals. Therefore, these materials will be discussed by elements. CALCIUM Soils need calcium to supply the nutrient needs of plants and maintain the desired physical and biological conditions in the soil. The available calcium is usually 40 to 80 pct of the exchangeable bases. (These bases are ones which can be displaced by other cations and determined quantitatively. They are then expressed as milliequivalents per hundred grams of soil-me.) Direct applications of lime materials such as burnt, ground or hydrated limes are the important sources of calcium for the soil. Most crops, especially legumes, have a high requirement for calcium. The average farmer does not use enough lime to maintain the proper level of available calcium. Hence, it is necessary for many fertilizers to contain soluble calcium materials for efficient use of the major nutrients. The following major nutrient carriers supply some calcium: calcium nitrate, ammonium nitrate mixtures and cyanamid, and many of the phosphates. Both synthetic and natural gypsum are used in fertilizer production. Some crops such as peanuts require a large amount of soluble calcium. Gypsum is the important supplier of this soluble calcium. It is not applied with the fertilizer

Jan 1, 1960

By Eric Sinkinson

MANY of the magnesite ores of the western part of the United States contain such large amounts of silica and hydrous silicate minerals that the value of the ores is either low or nominal. Expensive and carefully controlled mining methods are necessary to prevent excessive dilution of the higher grade ores by introduction in mining' of small pieces of the hanging walls or footwalls of the deposit. This difficulty is further complicated by the various states of decomposition of the country rock of the deposits in which many of the ores occur. The problem the authors attempted to solve arose from a request to float an impure magnesite containing varying proportions of siliceous gangue with calcium carbonate. The ore is normally. enclosed in serpen-tine masses, somewhat decomposed, and in mining it wall rock is inci-dentally added, so that variable amounts of siliceous material occur in the samples. The silica, alumina, and iron oxide are so closely associated with the magnesium carbonate in the magnesite that ordinary mechanical separation at coarse mesh sizes is of no avail. It is well known that calcium carbonate can be floated by suitable reagents, therefore it seemed reasonable to suppose that magnesium carbonate minerals would behave in a similar manner, but experimental trial proved that this supposition was unfounded. Therefore the first step in the problem was to find out what differences of behavior there were between magnesium and calcium carbonates under flotation conditions, or when suspended in water. In water at 18° C. magnesium carbonate is slightly more soluble than calcium carbonate; in fact, MgCO3 is soluble to the extent of 0.0106 grams in 100 c.c. of water at 18° C. and CaCO3 to the extent of 0.0013 grams. However, magnesium carbonate in water gradually changes to the basic carbonates of a composition (3MgCO3.Mg(OH)23H20) or (4MgCO3.Mg(OH)25H20), depending upon conditions, and calcium carbonate to calcium hydroxide, Ca(OH)2, The relative solubilities of these hydroxides in water are the reverse of the solubilities of magnesium and calcium carbonates.. The range in published figures for solubility

Jan 1, 1936

A discussion of the paper by Mr. Campbell, which was read by title at the Lake Superior meeting, but first presented at the New York meeting of the Iron and Steel Institute, October, 1904 (see p. 772). These papers are here published onder a mutual agreement between the Councils of the two Institutes, and will also be found in the Journal of the Iron and Steel Institute for the year 1901, vol. ii. Mr. William R. Webster, Philadelphia, Pa., said: We are under great obligation to Mr. Campbell for his exhaustive investigation, and the results he has put before us to-day. They are the most conlplete series of tests that have ever been made, where all the conditions of rolling, etc., were kept uniform. In discussing Mr. Campbell's first investigations, I claimed first, that the method of least squares, then used, would of necessity only gire the average value of any element, and that if the effect of any element was greater in the presence of high carbon than with low carbon this would not be shown by the method of least squares. Secondly, that the effect of manga nese should be considered on acid steel as well as on basic steel, instead of ignoring all the eff'ect of that element when it was below 0.60 per cent., as was then recommended by Mr. Campbell. I am pleased to note that the results of his present investigation confirm my views on these points. In presenting the results of his first investigation, Mr. Campbell referred to my investigation of 1893-94, and took exception to the value of phosphorus varying (depending on the amount of carbon present) from 800 to 1,500 lb. for each 0.01 per cent. He claimed that one might just as well consider the effect of phosphorus as being constant, and of carbon varying. I refer to this, as he now has introduced very similar conditions in his present tables, in that he gives variable values for manganese (depending on the amount of carbon present) for both acid and basic' steels. Can we now say, with more certainty than formerly, which element should be considered as haviup a constant effect ? There is one other point that I took up in my former discus-

Jan 1, 1905

By P. D. Merica

The remarkable phenomena exhibited by the aluminum alloy known as duralumin were discovered during the years 1903-1911 by A. Wilm1,2 and have been described by him and by others. 3 4 5 6 The unusual feature of this alloy is the fact, as was shown by Wilm, that it can be hardened quite appreciably by quenching from temperatures below its melting point followed by aging at ordinary temperatures, which consists merely f allowing the material to stand at these temperatures. The hardness is not produced by the quenching alone but increases during the period of aging, which may be from one to three days. Cohn3, 5 gives data showing the increase of hardness of duralumin during aging, after quenching in water from about 450° C. Upon annealing, the alloy so hardened by aging is softened exactly as is hardened steel. The composition of this alloy usually varies within the following limits: Copper, 3 to 4.5 per cent.; magnesium, 0.4 to 1.0 per cent.; manganese, 0 to 0.7 per cent.; aluminum, balance; iron (as impurities), 0.4 to 1 per cent.; silicon, 0.3 to 0.6 per cent. Its density is about 2.85. It is used only in the forged or rolled condition. This alloy has been produced for some years commercially and is in demand for the fabrication of parts for which both lightness and strength are required, such as for aircraft. Its tensile strength will average 50,000 to 60,000 lb. per. sq. in. (3515 to 4218, kg. per sq. cm.) after appropriate heat treatment, such as that described by Wilm.

Jan 6, 1919

By W. P. Lass

The purpose of this article is not only to describe the plant and method of cyaniding the Treadwell concentrates, but to present some of the results of the experimental work obtained in the past three years for the Alaska-Treadwell Qold Mining Co., at Douglas Island, Alaska, under the direction of F. W. Bradley, Consulting Engineer, and Robert A. Kinzie, General Superintendent, of the affiliated companies. At the time the experimental work was undertaken the concentrates were being shipped to the smeltery at Tacoma, Wash., and the cost for treatment of 3-oz. (gold) concentrates was $11.95 per ton, divided as follows : Smelting-charges,......... $4.00 Loading, freight, insurance, etc., . 2.89 Interest due to time loat in transit and in settlement,... 0.05 Loss due to settlement for 95 per cent. of the gold at $20 per ounce, 6.01 Total,...$11.95 From the experimental work described later, it was estimated that 96 per cent. extraction could be made by treatment on the ground, and that the cost, when treating 80 tons per day, would be $3.25 per ton, divided as follows : Per Day. Per Ton. Labor,. $86.16 $@.827 Chemicals,.76.60 0.960 Power and steam-heat,... 67.60 0.845 Marketing-, refining- and other charges, . 49.36 0.617 Totals,.. $2.59.72 $3.250 Adding to this total the 4 per cent. treatment-loss, which on 3-02. concentrates amounts to $2.48, gives a total cost of $5.13 per ton. Comparing this with $11.95, the cost when shipping to the smelter, leaves a net gain of $6.22 per ton by the local

Jan 1, 1912

By J. F. Poland

B. C. Burgess-—Prior to hearing this paper presented at the San Francisco meeting, I travelled by car from Yuma, Ariz., across south-central California and up through the San Joaquin Valley. After hearing the paper I returned by the coast route to San Diego then along the Mexican border to Yuma. The striking feature of these trips, related to this paper, was the dry river and creek beds at a time of year not the dry season. Contrasted with this was the wasteful use of water in irrigation canals and laterals. Poland says "at least 90 pct of the ground water pumped is used for irrigation." That being the case, it would appear that first consideration should be given to conservation of this use. Probably a small part of this is actually reaching the plants. Some measure of this loss between pump and crops would be revealing. Methods that might be employed to reduce this loss are pipe lines and spraying of some crops such as the banana planters are using in Central America. Another idea which might be investigated is to line canals and ditches with some water-repelling mineral like pyro-phyllite. Perhaps a comparatively thin sprayed-on

Jan 1, 1951

By J. F. Poland

B. C. Burgess-—Prior to hearing this paper presented at the San Francisco meeting, I travelled by car from Yuma, Ariz., across south-central California and up through the San Joaquin Valley. After hearing the paper I returned by the coast route to San Diego then along the Mexican border to Yuma. The striking feature of these trips, related to this paper, was the dry river and creek beds at a time of year not the dry season. Contrasted with this was the wasteful use of water in irrigation canals and laterals. Poland says "at least 90 pct of the ground water pumped is used for irrigation." That being the case, it would appear that first consideration should be given to conservation of this use. Probably a small part of this is actually reaching the plants. Some measure of this loss between pump and crops would be revealing. Methods that might be employed to reduce this loss are pipe lines and spraying of some crops such as the banana planters are using in Central America. Another idea which might be investigated is to line canals and ditches with some water-repelling mineral like pyro-phyllite. Perhaps a comparatively thin sprayed-on

Jan 1, 1951

By C. M. White

CITIZENSHIP is a rather abstract subject on which a great deal could be said-a subject on which a great deal is said -and still one which too many of us seldom think about and seldom work at. Too many of us engineers and business men have but a vague idea of citizenship. We think that if we go to the polls on election day and obey the laws scrupulously, with the exception of an occasional traffic violation, we are pretty good citizens and are doing our duty by our city, state, and nation. But when you think it over, that's a very passive observance of the important right of counting oneself a citizen of a country. There is nothing very positive in that attitude. There is nothing that indicates that we have sufficient interest to really go out and do a job for the -welfare of our country, forgetting any personal advantages or inconveniences that might arise. In other words, this type of voting-on-election- day, law-abiding citizenship does not keep us awake a single minute; it does not take any particular thought or require the expenditure of any time or energy.

Jan 1, 1939

By Y. Nakada, E. J. Fasiska, A. S. Keh, L. Zwell

DURING an investigation of solid-solution hardening of nickel by carbon,' we found that there were no reliable data on the dilating effect of dissolved carbon on the unit cell of nickel. Bernier2 reported an increase in lattice parameter of nickel (3.523A) when an unknown amount of carbon was introduced into solid solution (3.536A). Similarly KG, Tsien, and Misek3 found an increase from 3.523 to 3.531A when nickel was carburized. strong4 studied the variation of nickel lattice constant as a function of dissolved carbon. However, in his case carbon was introduced into nickel by solidifying the melt at 65 kbar. Therefore, his carbon concentrations were much above the highest equilibrium solubility limit5 (2.7 at. pct C at 1 atm). Knowledge of the lattice mismatch between solute and solvent is essential in understanding the mechanism of solid-solution hardening. Therefore, we decided to determine the dilation of the nickel lattice by carbon under the more usual conditions of atmospheric pressure. The material used was Inco Electrolytic Nickel of 99.95 pct purity, as specified by the supplier. The impurity contents in wt pct were: Fe, 0.01; Cu, 0.01; Co, 0.03; 0, 0.005; C, Si, S, N, trace. To this base material various amounts of AUC-grade high-purity carbon were added during vacuum induction casting. Ingots, 2 in. in diam, were heated in a muffle furnace at 1000°C for i hr., hot-rolled to 1/2-in. thickness, and quenched into brine. All ingots with carbon concentration greater than 0.98 at. pct were enclosed in a cast iron box during the heating to minimize decar-burization. Small pieces were then either swaged down to 0.028-in.-diam wire or cold-rolled to 0.010-in.-thick sheets. After the final cold reduction in area of 50 pct, the specimens were recrystallized by heating in evacuated capsules at 1100°C for 60 to 80 sec and then quenched into brine. The final grain size was 50 to 100 µ. The carbon contents of the alloys, Table I, were determined by a combustion method

Jan 1, 1969

By Ovid W. Eshbach

ENGINEERING education has been powerfully affected by the impact of war, just how powerfully can be better understood after considering the postwar problems regarding students, staff, and plant. In time of war no one will question the necessity of expediency of military training. With the cessation of hostilities, expediency gives way to the evolutionary process of strengthening engineering education as need is exemplified by experience. During the war, except for the Navy V-12 program, engineering education was at its lowest ebb of the century. Freshman enrollments were largely limited to those graduating from high school at the age of seventeen; and the upperclass, to those disqualified for active service. In most schools the experienced staff was either in service or government and industrial research. Many may never return to their former occupations. The most immediate problem is that of maintaining and building a staff to meet the enrollment of returning veterans. It is estimated that out of the eleven

Jan 1, 1945

By J. C. Williams, M. J. Blackburn

MANY aspects of the formation of the metastable w phase in titanium-transition metal alloys have been described in several recent papers.1-4 These papers have reviewed earlier work on the w phase and have further defined most of the important features related to the formation of this phase, e.g-., its crystal structure, composition, and morphology. There are, however, several important points regarding formation of the w phase in titanium alloys which have been described in less detail. Two of these are the relationship between lattice misfit and w phase morphology and the influence of lattice misfit on the mode of formation of the equilibrium a phase. In this communi- cation we will present transmission electron microscopy results relevant to these two points. The alloys used in this study were prepared by non-consumable electrode arc melting, each 30-g button being remelted a minimum of twelve times. The alloy compositions we have studied are listed in Table I. Thin foils were prepared using standard techniques described elsewhere. Two distinct c' phase morphologies have been reported in earlier papers. The phase is ellipsoidal in the Ti-Mo3 and Ti-Nbl system and cubical in the Ti-V3 system. Results of the present study show that the w phase is also cubical in Ti-Mn, Ti-Fe, and Ti-Cr alloys as illustrated in Fig. l(b) to (d). Fig. l(a) shows the ellipsoidal morphology in Ti-MO3 for comparison purposes. It was suggested in an earlier paper3 that the w phase morphology may be controlled by the lat-

Jan 1, 1970

By Paul F. Kerr, Raymond F. Robinson

Uranium mineralization occurs in the footwall of the Sunshine vein from the 2900 to the 3700 level. Veinlets of uraninite associated with pyrite and jasper have been so extensively divided and recemented that units more than a few feet in length are seldom observed. The wall rock is St. Regis quartzite of the Belt series. The age of the uraninite, on the basis of isotopic analyses, is 750 * 50, which agrees with geological data suggesting that phases of the Sunshine mineralization are pre Cambrian. THE Sunshine mine in the Coeur d'Alene district, Idaho, is well known for its silver-bearing veins but prior to the summer of 1949 had not been recognized as a possible source of uranium. At that time, during a geiger counter reconnaissance by T. E. Gillingham, R. F. Robinson, and E. E. Thurlow, high radioactivity was noted and radioactive specimens were collected from the footwall of the Sunshine vein.' The detection led to the identification of uraninite-bearing veins, since explored jointly by the Atomic Energy Commission and the Sunshine Mining Co. After the occurrence was noted, the geology of the uranium deposit was studied by the Sunshine staff, and a laboratory examination of the ores was conducted at Columbia University. Several types of laboratory work were undertaken. Differential thermal curves were made of selected siderite samples and results from many more were secured through the work of Mitcham.2 X-ray diffraction and X-ray fluorescence analyses were employed on uraninite, jasper, and siderite. Chemical analyses were made through the cooperation of the Division of Raw Materials of the Atomic Energy Commission. General Geological Features Several silver-bearing veins cut the overturned north limb of the Big Creek anticline as mapped by Shenon and McConne1,³ while the Osburn fault, a long-recognized regional feature about a mile away, marks the north boundary of the Silver Belt. The Sunshine vein, Fig. 1, has a south dip more or less parallel to the 60" axial plane of the fold and cuts rocks of the Belt. Series, starting with the Wallace formation near the surface, continuing downward through the St. Regis formation, and probably extending into the Revett quartzite which lies below the bottom or 3700-ft level. The limb of the anticline is locally modified by secondary folds, one being prominently exposed in the uranian area along the Jewel1 crosscut near the Sunshine vein. Crumpling of the limb resulted from compression which formed the anticline and probably preceded the faults in which the vein deposits accumulated. Evidence of drag along these faults points to reverse movement in the uranium-bearing area and elsewhere. This is true of major faults in the mine workings, and the majority of faults which can be mapped, as pointed out by Robinson.' The St. Regis formation, as measured in the mine, appears to have an initial thickness of some 2000 ft, but the apparent thickness due to thickening during folding is some 3400 ft. Along the Sunshine vein the purple and green rocks characteristic of the Wallace formation in the nearby Military Gulch section p. 37 of ref. 5) have been completely bleached because of introduced sericite. Hydrothermal solutions acting on the wall rock have substituted for the original color a pale greenish cast, although no pronounced mineralogical change has resulted, as Mitcham has observed.' The silver and the uranium depositions appear to belong to distinct epochs resulting from several periods of emplacement. Likewise, multiple periods of deformation account for the faulting. Uraninite is generally associated with silicification, while silver . mineralization accompanies carbonate veins. Rarely, uraninite may be found in a matrix of siderite. Ordinarily uraninite formed prior to ar-gentian tetrahedrite. Where clusters of veins form a stockwork, uraninite-jasper veins often favor one trend while tetrahedrite-siderite veins favor another. During deformation, brecciation of the St. Regis quartzite provided openings between broken rock fragments for precipitation from vein-forming solutions. Fractures due to major breaks were filled during the first stages of vein formation, while later deformation displaced the first veins and provided new channels along which further mineralizing solutions proceeded. The uraninite veins, as the first formed, have suffered fracturing, displacement, and segmentation. Uranian vein segments uncut by faults and more than a few feet in length are rare or nonexistent. Siderite veins are more massive and often extend without a break for tens and even hundreds of feet. In general they show much less segmentation. While the siderite is usually later, there is an overlap in the periods of deposition, some earlier siderite veins being extensively segmented in much the same way uraninite veins have been broken. Vein silica is more extensively distributed than the uranium and iron mineralization it carries. Along the vein course concentrations of uraninite frequently fade away and barren white quartz continues, the transition often occurring within a few feet along strike or down dip. An example appears on the 3700-ft level where a uraninite vein, see Fig. 2a,

Jan 1, 1954