Search Documents

By H. Biloni, R. Morando

The surface structure and substructure of Al-Cu alloys solidified as conventional ingots and under particular conditions such as those used by Bower and Flemings are studied. The influence of lampblack coating on the mold walls is especially considered and the results compared with those obtained in copper and graphite molds where no coatings exist. When high heat extraction conditions exist the observations show that mechanism of copious nucleation is responsible for most of the chill zone. When the heat extraction through the mold walls is low, a coarse grain structure with dendritic morphology arises, with a size that depends on the degree of convection present, analogous to that analyzed by Bower and Flemings. In both cases the effect of the convection on the macroscopic and microscopic appearance is discussed. The ingot macrostructure consists of one or more of three zones: "chill zone", "columnar zone", and central "equiaxed zone". The mechanism of the columnar-equiaxed transition has been subject of considerable interest and at present at least three theories exist about the formation of the equiaxed region: 1) the constitutional supercooling theory1 maintains that the equiaxed crystals nucleate after the columnar zone has formed, as a result of the constitutional supercooling of the remaining liquid; 2) chalmers2 pointed out, however, that there were several objections to this proposal, and that consideration should be given to the possibility that all the crystals, equiaxed as well as columnar, originated during the initial chilling of the liquid layer in contact with the mold; 3) Jackson et aL3 and O'Hara and ~iller~ suggested that a remelting mechanism of the dendrite arms is responsible for the formation of the equiaxed region. After the work of Cole and Bolling and other authors6 it became evident that convection (natural, reduced, or forced) plays a very important role in the transition from columnar to equiaxed and on the size of the resultant equiaxed structure. Until recently the accepted explanation of the chill zone was that it occurs as a result of copious nucleation in the liquid layer in contact with the mold walls.798 The columnar region is a subsequent result of the growth of favorably oriented grains and, as a result of a selection mechanism studied by Walton and Chalmers,9 elongated grains with marked texture are formed. Recently, however, Bower and Flemings" using an ingenious laboratory experiment introduced the idea that the "copious nucleation" mechanism is not responsible for the formation of the chill zone and that the presence of convection, introducing some form of "crystal multiplication", plays a decisive role in the formation of the chill zone. Unfortunately, it is important to consider that for their conclusions Bower and Flemings extrapolated the results obtained in their special experiments to the case of conventional ingots, and that these authors only analyzed the macrostructures of the specimens. Let us consider the work by Biloni and chalmers" concerning predendritic solidification. These authors were able to show that a study of the segregation substructure of A1-Cu gives information about the nucleation and growth of crystals formed in contact with a cold surface. A spherical predendritic region characterizes the first part of every grain nucleated in contact with the surface as a result of the chill effect. The aim of this paper is to elucidate through the observation of the segregation substructure the conditions under which (in the Bower and Flemings type of experiments and in conventional ingots) either the nucleation or the multiplication mechanism gives rise to the structure in contact with the mold walls. I) EXPERIMENTAL TECHNIQUES The experiments were performed on two alloys: Al-1 wt pct Cu and A1-5 wt pct Cu. The purity of the aluminum was 99.99 pct and the copper 99.999 pct. The results obtained with both alloys were similar. In the Bower and Flemings type of experiments the apparatus employed to obtain rapid solidification against a surface was similar to that used by those authors. The liquid was drawn by partial vacuum into the thin section mold cavity. Plate casts were 5 cm wide and usually 7.5 cm high. The thicknesses of the cast were 0.1 and 0.3 cm. Two different materials were used for the mold, copper and nuclear-grade graphite. The internal mold surfaces were polished and left uncoated for some experiments. In other experiments, the copper or graphite surface was coated with a thin film of lampblack material. In some of these particular experiments one of the mold walls was left with an uncoated region (usually in the form of a cross). The conventional ingots were cast in graphite or copper molds. In different experiments the mold walls were sometimes uncoated or coated with lampblack material. The results obtained in conventional and Bower and Flemings copper molds were compared with those obtained with copper molds coated with a very thin film of graphite; the results obtained were essentially similar. The size of the conventional ingots was 5 cm diam and 7 cm high in all cases. The cast surfaces produced by the Bower and Flemings type of experiments and conventional methods were observed macroscopically and microscopically without any metallographic preparation. As Biloni and Chalmers showed," the observation of the chill surface can give considerable information about the structure and segregation substructure.

Jan 1, 1969

By R. E. Wagner

MISSOURI's famous lead area, in what is known as Southeast Missouri, is locally termed the "Lead Belt." These deposits are in the Bonne Terre dolomite of late Cambrian age which has a thickness of nearly 400 ft. Underlying this is the La Motte sandstone which varies in thickness from 0 to 400 ft. The La Motte beds are deposited directly on the ancient erosion surface of Pre-Cambrian porphyries and granites of probably Algonkian age. The buried igneous peaks extend up into the Bonne Terre in several areas within the Lead Belt. Overlying the Bonne Terre are shales and siliceous dolomites of late Cambrian and early Ordovician age. Within the Lead Belt these have a thickness of from 0 to 500 ft. The district is bounded in general on the southwest by the Sims Mountain fault, on the northwest and north by the Big River fault, and on the

Jan 1, 1947

By C. E. Westley, R. R. Beebe

Recent works by Plaksh et al.,1,2 Glembotsky,3 and others have renewed interest in the effects of oxidation on the surface activity of the sulfides. Since considerable supporting data are available on galena-potassium ethyl xanthate, this system is being studied at South Dakota School of Mines and Technology by contact angle measurement, using the technique of McGlashan and McLeod.4 The contact-angle method is well adapted to investigation of the influence of small amounts of oxygen on the establishment of a stable contact angle on galena in potassium ethyl xanthate solution. Samples of massive galena containing less than 0.001 pct Cu, 0.001 pct Ag, and 0.01 pct Zn are mounted in castable plastic and ground and polished manually in a glove box containing the desired proportions of oxygen and purified nitrogen. Oxygen and nitrogen contents of the test atmosphere are determined with an Orsatt analyzer. In this way a reproducible surface is created in contact with whatever oxygen concentration is desired. Water and all reagents are prepared and stored in the test atmosphere. An absorbent is used to control carbon dioxide that might be present. Final polishing is done with levigated alumina on a glass plate. The prepared sample is placed in the test solution and transferred to the contact angle apparatus in a sealed box, and the test is conducted while both sample and solution are maintained under a slight positive pressure of the test atmosphere. Table I gives the results of contact angle measurements made at various 02-Nz concentrations.5 Each value of contact angle is the average of at least six individual measurements made with different bubbles at different locations on the sample surface. A period of 20 to 25 min has been found by preliminary tests to be sufficient to permit develop- ment of maximum angle, and all measurements are made after at least this much time has elapsed. Exposure of prepared samples to pure water under the test atmosphere before exposure to the xanthate results in a small but measureable and consistent reduction in contact angle. This is particularly true in the oxygen-deficient atmospheres; for example, at 2.2 pct O2 such water contact reduces the average angle about 8" from that obtained by immediate testing in xanthate. The general trend of increasing contact angle with increasing oxygen concentration corresponds to the results of Plaksin et a12 The absence of diminish-ment of contact angle at very high oxygen concentration has been attributed to the high concentration of xanthate per unit of galena surface: At oxygen concentrations below 1 pct (the limit of accuracy of the Orsatt analyzer), no contact angle is obtained. Furthermore, no contact angle is obtained at any oxygen concentration in the absence of xanthate. This result seems to be in disagreement with those cited by Plaksin.1 Further work on the interaction of galena and potassium ethyl xanthate or a similar collector as influenced by oxygen is contemplated. The true nature of the interrelation is as yet unknown. For example, it is not known whether the governing oxygen reaction is with the mineral, with the reagent, or with both.

Jan 1, 1961

By J. Blodget Britton

To the question, " Do the Pennsylvania anthracites contain phosphorus?" asked at the last meeting of the Institute during the discussion on the metallurgical value of Western lignites, I can now give a definite answer. Through the kindness of a gentleman connected with the Philadelphia and Reading Railroad, and another connected with one of the principal ironworks on the Lehigh, there was sent to the Ironmasters' Laboratory a number of samples of the coals now largely shipped from the Schuylkill and Lehigh regions. Seventeen of these I examined for their contents of ash and phosphorus, and obtained results as follows : Ash. Phosphorus. No. 1, . 4.10 .0063 2, . . . . 7.97 .0209 113, . 5.53 .0049 114, . . . . . . . 6.55 .0056 . 5, . 5.39 .0761 . . . . . . . 11 6, 14.15 .0593 7, . 10 43 ,0049 rl 8, . . . . . . . 5.29 .0354 9, . . . . . . . 3.01 .0042 6L10, . . . . . . 3.03 .0042 1 1 . 275 .0014 12, . 2.82 ,0111 l'13, . .3.69 trace L1 14, . . .2.35 trace 15, . . . . . . . 7.22 .0014 16, . . . . . . . 3.49 .0167 17, . 4.63 trace

Jan 1, 1920

By E. V. Murphree

CREATION of atomic energy, aside from its influence on war or peace, has posed these basic questions for the world: How soon can energy from atoms be harnessed to do man's daily work? How much of this power will there be, to what degree will it supplant present fuels, and what does it imply for the future of civilization? Answers to these questions may be found in part in analysis of just what atomic energy is and how far its development has come. The answers are encouraging. One of the first questions encountered in considering the application of atomic reactions is whether such reactions can be controlled. Fortunately, this has been adequately demonstrated by the operation of the Government plutonium plants at Hanford, Wash. Here nuclear reactions are carried out on a large scale involving liberation of about a billion B.t.u. per hour. This hourly heat liberation is equivalent to that obtained from about 7100 gallons of fuel oil. It has been possible to operate these plants day in and day out with the reaction controlled at the intensity desired. There should therefore be no question that, under proper conditions, reactions involving nuclear fission can be controlled.

Jan 1, 1946

By J. C. Bayles

Jan 1, 1886

By W. R. Shimer

In his valuable report on Finishing Temperatures and Properties of Rails,l Dr. G. X. Burgess, Chief of the Division of Metallurgy, U. S. Bureau of Standards, has begun a line of investigation which should be continued by those interested in the subject, and who have proper facilities for carrying out the work. For the past year or more the Bethlehem Steel Co. has been conducting experiments to learn the effect of rail finishing temperatures on their physical properties and microstructure and the results are here given for the consideration of those interested in the rail situation. Considerable differences of opinion have been expressed by various authorities, in the past, as to the effect of large or small grain size and high or low finishing temperatures of steel rails on their physical properties and wearing qualities. Low finishing temperatures and, therefore, low shrinkage, have been advocated on the theory that the wearing qualities would be improved. Others have recommended high finishing temperatures. The generally accepted cause for rail failures, due to the development of transverse fissures, is excessive wheel pressure on hard rails. One of the causes advanced for hard rails has been that they contain too high percentages of carbon and manganese; another that the rails were finished at too low a temperature, i.e., at or near the critical point. In the experiments herein described the rails were rolled from reheated blooms. All the rail blooms were charged hot in a reheating furnace and brought up to about the original ingot-rolling temperature before rolling into rails. These rails gave better results in deflection, withstood a greater number of drops before breaking, and showed greater ductility than rails of identically the same composition and section which were rolled direct from the ingot. Rails rolled from reheated blooms, finished at somewhat higher temperatures than when rolled direct from the ingot, have a different microstructure, which the writer does not believe is due so much to the difference in finishing temperatures, as to the difference in

Jan 1, 1915

By J. L. Gregg, C. W. Kuttner

ReceNtly there has been considerable interest in the production and use of extra hard alloys composed primarily of tungsten and carbon. Dr. Hoyt's recent paper1 gives a good description of these alloys and describes their performance when used as tools. There are a number of these alloys on the market sold under various trade names, and it is the purpose of this paper to describe the results of an investigation of the structure of five of these alloys by means of microscopic and X-ray methods. The samples studied were in the form of small tools or wiredrawing dies, which were either purchased or supplied as samples. They were in some cases not supplied by the original makers but were furnished by the agents in this country, and we wish to call attention to the fact that they may not be truly representative of the materials supplied under the various trade names No performance data are given and no inference as to the inferiority of one alloy as against any other is made. K. Schröter2 recently described methods for polishing alloys of this type for microscopic examination and has presented photomicrographs of several alloys. However, he did not identify their constituents or describe methods for their identification. Constituents and Their Identification As far back as 1915 attempts were made to utilize tungsten carbides commercially, but the great brittleness of these carbides made these first attempts unsuccessful. Later, successful dies were made by sintering the powdered carbides with small amounts of iron, nickel, or cobalt. Due to the high melting points of the tungsten carbides (2600" to 2800" C.), it is difficult to melt the carbides without volatilizing almost quantitatively the added element of the iron group. Inasmuch as the added metal does not exceed 20 per cent. and is usually present in much smaller amounts, some understanding of the tungsten-carbon equilibrium dia-

Jan 1, 1929

By C. W. Kuttner, J. L. Gregg

ReceNtly there has been considerable interest in the production and use of extra hard alloys composed primarily of tungsten and carbon. Dr. Hoyt's recent paper1 gives a good description of these alloys and describes their performance when used as tools. There are a number of these alloys on the market sold under various trade names, and it is the purpose of this paper to describe the results of an investigation of the structure of five of these alloys by means of microscopic and X-ray methods. The samples studied were in the form of small tools or wiredrawing dies, which were either purchased or supplied as samples. They were in some cases not supplied by the original makers but were furnished by the agents in this country, and we wish to call attention to the fact that they may not be truly representative of the materials supplied under the various trade names No performance data are given and no inference as to the inferiority of one alloy as against any other is made. K. Schröter2 recently described methods for polishing alloys of this type for microscopic examination and has presented photomicrographs of several alloys. However, he did not identify their constituents or describe methods for their identification. Constituents and Their Identification As far back as 1915 attempts were made to utilize tungsten carbides commercially, but the great brittleness of these carbides made these first attempts unsuccessful. Later, successful dies were made by sintering the powdered carbides with small amounts of iron, nickel, or cobalt. Due to the high melting points of the tungsten carbides (2600" to 2800" C.), it is difficult to melt the carbides without volatilizing almost quantitatively the added element of the iron group. Inasmuch as the added metal does not exceed 20 per cent. and is usually present in much smaller amounts, some understanding of the tungsten-carbon equilibrium dia-

Jan 1, 1929

By C. H. Mathewson, P.W. Bakararian

The greatcr part of the literature on the plastic behavior of magnesium dates back to that active period of research in crystal mechanics immediately following the widespread preparation of isolated metallic crystals large enough for the application of conventional methods of mechanical testing. These investigations, performed on single crystals, revealed an analogy between zinc and magnesium with respect to their fundamental mode of deformation. in the operation of glide and twinning, respectively, on crystallographically similar planes. Mathewson and Phillips (1928)' by geometrical analysis identified the plane in magnesium as the twinning plane. Schiebold and Siebel (1931) confirmed this twinning planc, established the basal plane as the plane of slip, and a digonal axis I as the slip direction. They also rcported twin formation in a secondary role on the {IOI} plane. Schmid (1931)³ summarized and discussed the earlier evidence and presented the results of his own experiments on the effect of temperature and small amounts of soluble elements. From X-ray studies on extended wire single crystals, he concluded that slip along the basal plane in the direction of the digonal axis I closest to the stress direction was the sole slip system operating at atmospheric temperature. This conclusion was based on experiments with crystals of many different orientations relative to the stress axis. Special attention was directed to the basal plane and the digonal axis I, as the plane and direction of greatest atomic density. Determinations of resolved shear stress at the onset of plastic yielding-—i.e., the critical resolved shear stress—were also made; the average of these calculations showing 82.9 grams per sq. mm. This value varied only slightly up to 300°C. at which temperature it was found to decrease to 70.5 grams per sq. mm. The extension of his crystals at temperatures above 225°C. further disclosed the presence of new slip systems. After the origince specimens of circular section had been

Jan 1, 1943

By C. H. Mathewson, P. W. Bakararian

The greatcr part of the literature on the plastic behavior of magnesium dates back to that active period of research in crystal mechanics immediately following the widespread preparation of isolated metallic crystals large enough for the application of conventional methods of mechanical testing. These investigations, performed on single crystals, revealed an analogy between zinc and magnesium with respect to their fundamental mode of deformation. in the operation of glide and twinning, respectively, on crystallographically similar planes. Mathewson and Phillips (1928)' by geometrical analysis identified the plane in magnesium as the twinning plane. Schiebold and Siebel (1931) confirmed this twinning planc, established the basal plane as the plane of slip, and a digonal axis I as the slip direction. They also rcported twin formation in a secondary role on the {IOI} plane. Schmid (1931)³ summarized and discussed the earlier evidence and presented the results of his own experiments on the effect of temperature and small amounts of soluble elements. From X-ray studies on extended wire single crystals, he concluded that slip along the basal plane in the direction of the digonal axis I closest to the stress direction was the sole slip system operating at atmospheric temperature. This conclusion was based on experiments with crystals of many different orientations relative to the stress axis. Special attention was directed to the basal plane and the digonal axis I, as the plane and direction of greatest atomic density. Determinations of resolved shear stress at the onset of plastic yielding-—i.e., the critical resolved shear stress—were also made; the average of these calculations showing 82.9 grams per sq. mm. This value varied only slightly up to 300°C. at which temperature it was found to decrease to 70.5 grams per sq. mm. The extension of his crystals at temperatures above 225°C. further disclosed the presence of new slip systems. After the origince specimens of circular section had been

Jan 1, 1943

By John T. Norton, Robert J. Anderson

The purpose of this paper is to report evidence, regarding metal structures, that is contradictory to the amorphous-metal hypothesis of Beilby, and particularly evidence that is opposed to the proposition that a vitreous amorphous layer is produced by polishing a piece of metal. According to the theory of Beilby, which has been developed by Rosenhain and others, polishing a piece of metal greatly affects the condition of the metal at or near the surface polished, making that surface entirely different in character from the metal beneath. A vitreous amorphous surface film is said to be formed. The polishing process, on the basis of Beilby's explanation, is well known and does not require discussion here, but it is advisable to seek the precise meaning of the term "amorphous." According to Beilby, "amorphous means non-crystalline in the most intimate sense of the word; the molecules arc not marshalled in crystalline order and orientation." According to Rosenhain, the amorphous condition is that assumed by a metal when the crystalline arrangement is completely broken up so that the atoms exist in a state of disorderly arrangement similar to that which exists in the liquid state. Thus, from the point of view of the phase rule, the "amorphous phase" is regarded as being identical with the liquid phase. Amorphous metal is often likened to an undercooled liquid. A crystalline substance is one in which the atoms are arranged in space according to some definite repeating geometrical pattern. The existence of amorphous metal has not been definitely proved. The evidence offered here that amorphous metal probably does not exist is of a direct nature and is afforded by x-ray diffraction effects given by a number of metals and alloys when polished, cold-worked, and annealed. Considerable of the experimental work was carried out with substantially pure aluminum and the aluminum alloy duralumin, but many of the observations made on these materials were checked by similar observations on copper, iron, tin, zinc, lead, mild steels, and

Jan 1, 1925

By F. Osmond

When a metal (whether a simple substance, an alloy, or a compound) presents, in each of the smallest parts to which it can be redueed by mechanical division, a constant chemical composition, it is defined as chemically homogeneous. But chemical hombgeneity by no means necessitates mechanical homogeneity. There are no perfectly amorphous metals. Crystalline forces, on the one hand, and tensions or compressions, on the other band, determined by icequalities of temperature in the mass during heating or cooling, give rise in every metal to the formation of geometric elements of structure. These elements may, moreover, assume perfect crystalline forms, with their planes of cleavage; or embryonic crystalline forms, segregated in the midst of. a paste of confused organization; or pseudo-crystalline forms of expansion and contraction, like those produced in the drying of gelatinous precipitates or (most frequently) these different forms associated. 111 either case the adhesions between two adjoining structural elements, respectively homogeneous, may be very different from the interior cohesion of each of these elements. The mechanical properties of this complex aggregate cannot be simple, and, when it is submitted to strains sufficient to produce deformation, the results may be very different according to the type of structure or the manner in which it is affected by the strains. It may be fairly said that a metal does not present a single resistance to tension, or a single resistance to compression, etc., but in fact, at least theoretically, as many resistances to tension, compression, etc., as it may possess coexistent features of structure; only, in any single test, it is the weakest of the resistances involved which makes itself evident. For further explanation, let us imagine a cylinder A B (Fig. I), formed of two similar halves A and B, placed together upon their common base x y. Such a system evidently presents no resistance to axial tension, while it would resist axial compression like a single

Jan 1, 1894

By R. M. Brick

The etched mierostructures of cold-worked alpha brasses, after reductions in excess of about 20 per cent, exhibit dark lines or markings, which have been termed "deformation bands," "etch bands," and "strain markings." The terms will be used synonymously in this report. The markings are similar in their general appearance to etch figures found in cold-worked iron, aluminum and other cubic metals but in certain respects may differ noticeably. At reductions of from about 20 to 50 per cent in brass, they appear as straight dark lines of irregular spacing and at random directions in different grains, but apparently intimately associated with definite crystallographic planes, usually {ill), in each crystal. At higher reductions, the markings on the rolling plane tend to appear in a direction transverse to the rolling direction in all crystals but may bend away at considerable angles, particularly near grain boundaries. Samans,1 on the basis of X-ray and micrographic studies of two single crystals of brass, rolled to a 50 per cent reduction, showed that the lines of deformation were the edges of thin mechanical twins parallel to octahedral planes. Barrett and Levenson2-4 have made comprehensive studies of the deformation of iron and of aluminum. They show that in these two metals the deformation markings originate by division of the original homogeneous crystal into banded areas differing in orientation by an amount that increases with the degree of deformation. The markings thus cannot be twin bands, and Barrett, in a review of this subject,2 attributed Samans' results on brass to an accidental choice of deformation that left the bands in approximately a twinned relationship. On the other hand, Mathewson6 has suggested that in some cases mechanical twinning offers a better rationalization of the coverage of some (111) pole figures of worked brass than the assumption of band rotation into symmetry positions. Considering next a deformed and annealed alpha brass, the most striking aspect of its microstructure is the multiplicity of twin bands.

Jan 1, 1940

By R. M. Brick

The etched mierostructures of cold-worked alpha brasses, after reductions in excess of about 20 per cent, exhibit dark lines or markings, which have been termed "deformation bands," "etch bands," and "strain markings." The terms will be used synonymously in this report. The markings are similar in their general appearance to etch figures found in cold-worked iron, aluminum and other cubic metals but in certain respects may differ noticeably. At reductions of from about 20 to 50 per cent in brass, they appear as straight dark lines of irregular spacing and at random directions in different grains, but apparently intimately associated with definite crystallographic planes, usually {ill), in each crystal. At higher reductions, the markings on the rolling plane tend to appear in a direction transverse to the rolling direction in all crystals but may bend away at considerable angles, particularly near grain boundaries. Samans,1 on the basis of X-ray and micrographic studies of two single crystals of brass, rolled to a 50 per cent reduction, showed that the lines of deformation were the edges of thin mechanical twins parallel to octahedral planes. Barrett and Levenson2-4 have made comprehensive studies of the deformation of iron and of aluminum. They show that in these two metals the deformation markings originate by division of the original homogeneous crystal into banded areas differing in orientation by an amount that increases with the degree of deformation. The markings thus cannot be twin bands, and Barrett, in a review of this subject,2 attributed Samans' results on brass to an accidental choice of deformation that left the bands in approximately a twinned relationship. On the other hand, Mathewson6 has suggested that in some cases mechanical twinning offers a better rationalization of the coverage of some (111) pole figures of worked brass than the assumption of band rotation into symmetry positions. Considering next a deformed and annealed alpha brass, the most striking aspect of its microstructure is the multiplicity of twin bands.

Jan 1, 1940

By Brahm Prakash, R. Schuhmann

Chemical conditions for flotation and nonflotation of cassiterite and fluorite with oleic acid as collector and with alizarin dyes as modifying agents were studied by means of small-scale, vacuum-flotation tests. Artificial cassiterite was prepared fot these tests by high-temperature methods, especially by crystallization from borax melts. FLOTATION test work on Bolivian tin ores some years ago led to the development of several workable schemes of selective soap flotation, but left unanswered many questions of soap-flotation chemistry.' Accordingly, the study of the activation and soap flotation of quartz just reported? was undertaken as a start toward the elucidation of some of the unanswered questions. The experimental work on quartz flotation consisted primarily of small-scale, vacuum-flotation tests in which activator and collector additions and pH were varied between wide limits. In the work to be described in this paper, the soap flotation of cassiterite and fluorite was studied by the vacuum-flotation technique developed in the previous study of quartz. Using oleic acid as collector, conditions for floating cassiterite and fluorite in the absence of modifying agents were first determined. Then the effects of barium, calcium, and alizarin dyes on the flotation of cassiterite, fluorite, and quartz were studied. Alizarin dyes were chosen for study because of the promise they have shown as selective modifying agents in the flotation of non-sulphide minerals.12,1 Also, they form a family of reagents in which there should be a systematic correlation of chemical properties with composition. As a preliminary to the study of cassiterite flotation, an investigation of the preparation of synthetic cassiterite and X ray studies of natural and synthetic cassiterite were undertaken. Experimental Methods The flotation technique and most of the reagent preparations were described fully in the previous paper.' In addition, for the present work it was necessary to prepare satisfactory stocks of clean cassiterite and fluorite and to obtain samples of alizarin dyes. Cassiterite: High-grade cassiterite from the Netherlands East Indies was crushed, sized, and cleaned

Jan 1, 1951

By Brahm Prakash, R. Schuhmann

Chemical conditions for flotation and nonflotation of cassiterite and fluorite with oleic acid as collector and with alizarin dyes as modifying agents were studied by means of small-scale, vacuum-flotation tests. Artificial cassiterite was prepared fot these tests by high-temperature methods, especially by crystallization from borax melts. FLOTATION test work on Bolivian tin ores some years ago led to the development of several workable schemes of selective soap flotation, but left unanswered many questions of soap-flotation chemistry.' Accordingly, the study of the activation and soap flotation of quartz just reported? was undertaken as a start toward the elucidation of some of the unanswered questions. The experimental work on quartz flotation consisted primarily of small-scale, vacuum-flotation tests in which activator and collector additions and pH were varied between wide limits. In the work to be described in this paper, the soap flotation of cassiterite and fluorite was studied by the vacuum-flotation technique developed in the previous study of quartz. Using oleic acid as collector, conditions for floating cassiterite and fluorite in the absence of modifying agents were first determined. Then the effects of barium, calcium, and alizarin dyes on the flotation of cassiterite, fluorite, and quartz were studied. Alizarin dyes were chosen for study because of the promise they have shown as selective modifying agents in the flotation of non-sulphide minerals.12,1 Also, they form a family of reagents in which there should be a systematic correlation of chemical properties with composition. As a preliminary to the study of cassiterite flotation, an investigation of the preparation of synthetic cassiterite and X ray studies of natural and synthetic cassiterite were undertaken. Experimental Methods The flotation technique and most of the reagent preparations were described fully in the previous paper.' In addition, for the present work it was necessary to prepare satisfactory stocks of clean cassiterite and fluorite and to obtain samples of alizarin dyes. Cassiterite: High-grade cassiterite from the Netherlands East Indies was crushed, sized, and cleaned

Jan 1, 1951

By Harry Roeser

Short cuts for determining the constants of oil decline curves, with the method of least squares as a starting point, are presented and applications made to practical examples. The nature of the raw data does not justify rigid adherence to the orthodox theory but does lend justification to convenient methods of approximation within reasonable limits. If the conventional form y = kxn were changed to y = k(x + c)', methods of determining the curves would be simplified and greater uniformity in calculated results would probably follow. As A result of the publication, several years ago, of some articles on determining the constants of empirical formulas, the determining the constant's of types of curves used for estimating the production decline of oil wells was brought to the writer for study. Methods requiring a minimum of time and labor and a maximum of rigor were sought, as it appeared that the nature of the data from which such curves are computed and the relative uncertainty of occurrence of the events predicted from them did not justify close adherence to the theory on which the solution of such problems is ordinarily based. The technical deficiencies of the solutions presented in this paper, from the standpoint of the method of least squares, are readily apparent to those familiar with that method, but their presentation in detail here is irrelevant to the subject matter. However, it is the author's conviction, after a rather exhaustive study of the problem, that the value of the solutions lose little by the approximate application of the conventional theory. It must be understood by those who use these formulas that the solutions herein given, and the formulas based on them, are merely facilities to aid the valuation engineer in forecasting future events. It is assumed, also, that before application is made of them, prescient judgment based on the circumstances in each case, shows that the forecast has some probability of realization. On this basis only will these formulas be found useful.

Jan 6, 1924

By L. S. Darken, H. A. Wriedt

In a previous paper,1 an experimental study of nitrogen dissolved in a cold-rolled ad heat-treated, low-carbon steel at 300° to 450°C yielded the equilibrium solubility relations and the concentrations of the two types of deject sites involved. In this paper, the probable identities of the defects that absorb nitrogen are restricted from the available evidence to screw dislocatioms for B sites, and to either micro crack surfaces or edge In a previous paper.' we reported an experimental study of the excess nitrogen solubility in a low-carbon steel produced by a combination of plastic deformation and nonrecrystallizing heat treatment. The concentrations of the defect sites that absorb the excess nitrogen were measured in terms of their capacities for nitrogen. Also measured were the equilibria of nitrogen distribution among the sites. Several problems and questions arise from these measurements. We should like a physical identifi- dislocations for A sites. The concentrations of these defects in experimental steel specimens are estimated from the concentrations of defect sites. finally, the influence of chemical composition upon the nitrogen-trapping defects—the relative numbers generated in deformation, the relative numbers surviving as temperature is raised, the apparent numbers observed, and the distribution equilibria-is discussed. cation of the defects involved and of the two kinds of nitrogen-absorbing sites, called A and B types, upon those defects; the concentrations of the defects themselves could then be computed. We should also like to know how exclusively the findings apply to the "X steel" used in the experiments and to what extent they apply to cold-rolled steel given no subsequent treatment. By considering the data already given, together with results from a few specific tests which will be reported as they are invoked, we are able to eliminate some interpretations altogether and to secure an acceptable though limited interpretation from among the remaining possibilities.

Jan 1, 1965