Search Documents

By AIME AIME

Maurer's review summarizes quite thoroughly the various theoretical developments and experimental findings that contribute to the knowledge of rock mechanics in drilling. This discussion supplements Maurer's paper by including generalities that either have been incompletely treated in his review, or formulated from new considerations by the discussant and from hitherto unpublished experimental data. These generalities are associated with the observation that all mechanical methods of rock drilling essentially comprise a sequence of indexed, concentrated loadings on the bottom of the hole being drilled.

Jan 1, 1967

By George W. Riter

Discussion of the paper of H. 0. Hofman and C. R. Hayward, presented at the New Haven Meeting, February, 1909, and printed in Bulletin No. 30, June, 1909, pp. 513 to 529. GEORGE W. RITER, Salt Lake City, Utah (communication to the Secretary*).-In their paper, Messrs. Hofman and Hayward deal with a branch of silver metallurgy that is on very uncertain ground, both as a commercial process and as a metallurgical science; moreover, its field is limited to few localities and to peculiar conditions. The literature on the subject is incomplete and full of conflicts. The paper under discussion clears u p no disputed points; on the contrary, because of hasty generalization, its tendency is towards further confusion. In Table I., the authors assume that each test-lot of 1,800 g. of ore contained exactly 5.499 g. of silver, that any variation in the quantity of silver recovered, however slight, should be ascribed to variation in the time of grinding. It is barely possible that the ore was mixed so uniformly as to justify this assumption; but those of us who know how difficult it is to get uniform samples of any ore in which silver mineral is present in rich particles will have a doubt on this point. The unlikelihood of getting absolutely uniform test-lots of ore also reflects on the data in Table II., on the effect of varying the amount of salt in a pan-charge. The authors say " The salt series was the last one that was investigated." This again raises a question as to whether the ore was split into test-lots at the time of sampling, or whether it was kept in bulk in such a way as to permit mechanical concentration of values before the end of the experiments. The conclusion following Table II.: " There is no reason, therefore, for going beyond six per cent. of salt," is hardly to the point. If we assume that salt is of benefit only when in solution, it follows that the relation between the quantity of salt

Mar 1, 1910

By E. W. Davis

DURING late years, the proportion of beileficiated iron ore shipped from the Lake Superior District has increased very rapidly. By benefication is meant washing, screening, drying, sintering or any process by which the grade or structure of the crude ore is improved before shipment. In 1915, only 3,000,- 000 tons, or 9 per cent, of t6e total Minnesota shipment was beneficiated ore, compared with 13,500,000 tons, or 35 per cent, of the total Minnesota shipment in 1925. This increase is, of course, due to the fact that iron and steel can be made more cheaply after beneficiating these ores than they could have been had these ores not been so treated. Fundamentally, however, several causes contribute to the necessity for beneficiating iron ores, such as depletion of the reserves of high-grade ores, the iron ore leasing systems and taxation methods and, at the smelting plants, a better understanding of blast-furnace operations, increased operating costs and increased sulfur content of blast-furnace coke. As economic conditions change, it is by no means certain that the proportion of beneficiated ore shipped each year is going to continue to increase. Undoubtedly some of the beneficiation operations are not economically sound at the present time and what the future has in store for the iron ore industry is problematical. Generally speaking, the cost of fuel for blast-furnace operations will increase as time goes on and in order to continue to produce cheap iron and steel, some of the other costs must be lowered. Freight and labor rates probably can- not be reduced. The cost of producing iron ore cannot be reduced much below the present price. It therefore appears that the best opportunity for maintaining iron and steel prices at their present level in spite of in- creased costs of labor and raw materials is to use. less or cheaper raw materials. This, of course, contemplates an improvement in metallurgical processes all along the line and, as a matter of fact, we can confidently expect these improvements because scientific investigations will undoubtedly be even more productive in the future than they have been in the past.

Jan 1, 1926

NEW MEMBERS The following list comprises the names of those persons who became members during the period Apr. 10, 1919, to May 10, 1919. BEAVER, JAMES J., Supt., Mech. Ore Loaders, Tennessee Coal, Iron & R.R. Co., Box 62, Bessemer, Ala. BLACKWELDER, ELIOT Geol. & Prof. of Geol., Univ. of Ill., Urbana, Ill. BRAECKE, GUSTAVE E., -Min. Engr., Mgr., Societe Curas et Soldado, La Carolina, Spain. BRINK, CYRIL GORDON, Reduction Officer, Charge of Reduction Works. Fairview Devonian Montrose Gold Mines, Ltd., P. O. Sheba, Transvaal, So. Africa. COMERFORD, JOSEPH S., Chief Chem. & Met., American Manganese Steel Co., New Castle, Delaware. DROSDOWSKI, N. C. V., Asst. Supt.,, The Spassky Copper Mine, Ltd., Karagandy, Akmolinsk, Oblast, Siberia. DUNGLINSON, GEORGE, JR., Asst. to Gen'l Mgr., Norfolk & Western Railroad, Bluefield, W. Va. FARAGHER, PAUL VANCE, Research Fellow on Light Metals, Mellon Institute, Pittsburgh, Pa.

Jan 6, 1919

By Hans Lundberg, Basil T. Wilson, H. Steuart Scott

FOR the benefit of those readers who may not be in close touch with present practices in the geophysical prospecting for ore, brief reference will fiat be made to the advantages and shortcomings of the methods to be discussed. Magnetic and electric methods are generally accepted as the most useful for ore prospecting. By magnetic methods, magnetic intensities that are not normal may be recorded and outlined. From these can he located concentrations of such highly magnetic minerals as magnetite or pyrrhotite, which sometimes occur in such large masses that they are of economic value in themselves. More often. however, these magnetic min¬erals are associated with others, such as copper, zinc, lead, gold, and silver, which, if existing in sufficient concentration and quantity, may constitute valuable ore bodies. It is therefore only when pyrrhotite and magnetite are present in these bodies that the magnetic method can be used to indicate their presence.

Jan 1, 1945

"The Washoe Smelter is situated about two miles east of the City of Anaconda. The smelter site includes about 240 acres and peculiarly adapts itself in topography to the efficient handling of material. By reason of its being on a hill side it is possible to make the level of delivery of the product of one building the level of the charge floor of the next succeeding one.THE ORES: The ore treated comes principally from the Butte district and is hauled by the Butte, Anaconda & Pacific railway, a distance of twenty-eight miles, in trains of fifty 50-ton bottom-dump cars to the railroad yards at East Anaconda. At this point these trains are• split up according to their destination,—that is, as to whether they go to the concentrator and sampling mill ore bins, or to the storage bins. In each case they are made up into trains of eight or sixteen cars, according to the size of engine to be used, and are carefully weighed before delivery to their respective bills.Some idea of the magnitude of the works may be obtained from the following figures:Amount of ore that can be treated in 24 hours…12,000 tonsLime rock from adjacent quarries…2,300 tonsCoke used…500 tonsCoal for reverberatory use…500 tonsCoal for power use…50 tonsWater, per minute, 35,000 gallons.Men employed in and around Anaconda, 3,000. Monthly payroll for above, $300,000.00."

Jan 1, 1913

New York Meets first Wednesday after first Tuesday of each month. Chairman. PERCY E. BARBOUR, Vice-Chairman. A. D. BEERS, Secretary, 55 Wall St., New York, N. Y. C. A. BOHN,.Treasurer. JOHN V. N. DORR, LEWIS W. FRANCIS. Boston Meets first Monday of each winter month. W.. E. C. EUSTIS. Chairman. R. L. AGASSIZ. Vice-Chairman. E. E. BUGBEE, Secretary-Treasurer, Mass. Inst. of Technology, Cambridge, Mass. ALBERT SAUVEUR, H. L. SMYTH. Columbia Holds four sessions during year. Annual meeting n September or October. W. H. LINNEY, Chairman. OSCAR LACHMUND, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash. STANLY A. EASTON. S. SHEDD. Puget Sound Meets second Saturday of each month SIMON H. ASH, Chairman. I. F. LAUCKS, Vice-Chairman. CHARLES SIMENSTAD, Secretary-Treasurer, 425 Lyon Bldg., Seattle, Wash. GLENVILLE A. COLLINS, JOHN N. POTT

Jan 5, 1917

By John H. Harden

In the valuable paper of Mr. Dunbar D. Scott and its varied discussion, on the evolution of mine-surveying instruments, the tripod-head has not received the attention it merits. During the last 50 years this very necessary adjunct to the surveyor's instrument has been much improved. The legs are of better construction; and the devices for laterally moving the instrument over the station-point and for quick leveling, without the use of the screws, have given to the instrument fitted with the modern tripod-head the same facilities possessed by the oldfashioned ball-and-socket, with more perfect accuracy, not attainable in the latter, while saving from 30 to 50 per cent. of the time required for setting the instrument over a station. For the purpose of extending the discussion to this import-

Jan 1, 1902

[based on o report by HUBERT E. RISSER] There is a tendency among laymen to relegate America's coal industry to Pennsylvania and West Virginia, completely overlooking-or unaware of- the vast reserves, both those developed and those untapped, situated in the 1.4 million square miles between the Appalachians and the Rockies. At the 1965 AIME Annual Meeting, Hubert E. Risser, Principal Mineral Economist of the Illinois State Geological Survey, presented an interesting picture of the wealth of mineral fuels occurring in that area. In his talk entitled "Trends in Mineral Fuels in the Central United States", Mr. Risser underscored the fact that "more than half of the nation's known reserves of each of the three major fuels-oil, gas and coal-lie within the Central area." The highlights of his speech, with emphasis on the coal situation, are excerpted below.

Jan 6, 1965

By Thomas T., Read

IN this survey of the progressive development (of education for the mineral industries throughout the United States, the review of .the history of each school has usually been completed wherever it is first mentioned, but the history of the schools in the cities of the eastern seaboard was not carried beyond 1870. It is necessary now to cover what happened during the period of approximately the last quarter of the nineteenth century in several of the schools in the east. Philadelphia Of Philadelphia, it has been related in chapter 4 that the Polytechnic College of Pennsylvania began offering a curriculum leading to the B.S. in mining in 1853; that the school did not prosper, and finally closed about 1890. The establishment of a Department of Mining, Arts, and Manufactures at the University of Pennsylvania in 1855-56 was also mentioned, but its history was not carried beyond 1860. In 1859 J. Peter Lesley was appointed professor of mining in the University of Pennsylvania. The son of a cabinetmaker, born in Philadelphia Sept. 17, 1819, he had taken his A.B. degree at the University of Pennsylvania in 1838 and then secured a position on the Geological Survey of Pennsylvania under H. D. Rogers. When the Survey was discontinued, in 1841, he went to Princeton to study theology, was ordained a Presbyterian minister and followed that career until 1852, when the Pennsylvania, Geological Survey was again started and he rejoined its staff. He published "A Manual of Coal and its Topography" in 1856, and studied at the École des Mines, Paris, in 1856-57. He published an 800-page "Iron Manufactures Guide" the year that he was appointed to the staff at the University of Pennsylvania. In 1863-64 a College of Agriculture, Mines, Arts and the Mechanic Arts was established, but it was not a separate school

Jan 1, 1941

By Mario L. Villa

Another increase in production and the discovery of new pools arc the outstanding developments of the year 1937. Production in 1937 totaled 16,354,706 bbl., compared to 15,457,953 bbl. in the previous year, an increase of 5.8 per cent, of which 5 per cent was due to the Yacimientos Petroliferos Fiscales (Argentine Governnlent Oil Fields) and 0.8 per cent t,o private companies. Table I shows that the most important gain in output was obtained in zone B of Comodoro Rivadavia, partly offset by a 5.7 per cent decrease in the Neuqu6n district. The fields of Salta and Mendoza show an increase of 4.4 and 39.1 per cent, respectively. The determination of bottom-hole pressures was started by Yaci-mientos Petroliferos Fiscales (Y.Y.F.) in Comodoro Rivadavia and

Jan 1, 1938

Few people in the industry today are competent to comment on the O.G. system for vessel covers, but with papers as well prepared as Mr. Bradley's we will soon be well informed. I would like to direct these comments to Mr. Klaes of Ford Motor Company. Mr. Klaes' description of their steaming hood agrees with our experience at Weirton. We have been able to stay within design limits and, as a result, have had few problems with our auxiliary equipment. Our main problem, as with Ford, has been thinning of our vessel cover tubes. At Weirton, controlled circulation, high pressure boilers are in use as heat recovery units above the BOP vessels. The boilers are provided with "off cycle' oil firing equipment. A Venturi type wet gas scrubber follows the boiler to complete the vessel draft system.

Jan 1, 1972

By AIME AIME

N OW THAT the war is over it is possible to release data and correct some erroneous statements and impressions relative to the use of manganese-steel armor and helmets, which heretofore have been carefully guarded. The material of the helmets furnished to the English, American, and Belgian armies was invented by Sir Robert Hadfield, Bart., F.R.S., and was described in a paper read by him at the International Engineering Congress in August, 1893. The French helmet was 2 oz. lighter than the English but had a greatly inferior resistance. Tests showed that it was perforable at as low a velocity as 350 ft.- sec. impact of the standard shrapnel bullets. Helmets made of the Hadfield "Era" manganese steel kept out standard shrapnel bullets of the same quality at no less than from 750 to 950 ft.-sec. impact velocity. The respective energies were, in the case of the French helmet, only 0.021 ft.-tons, 46 ft.-lb., and in the British 0.095 ft.-tons, 213 ft.-lb. The German helmet was made of nickel-chromium steel and, although 12 oz. heavier and 12 per cent. thicker than the Hadfield, was not only perforate

Jan 1, 1920

New York Meets first Wednesday after first Tuesday of each month. Chairman. PERCY E. BARBOUR, Vice-Chairman. A. D. BEERS, Secretary, 55 Wall St., New York, N. Y. C. A. BOHN, Treasurer. JOHN V. N. DORR, LEWIS W. FRANCIS. Boston Meets first Monday of each winter month. R. L. AGASSIZ, Chairman. JAMES G. CARLETON, Vice-Chairman. E. E. BUGBEE, Secretary-Treasurer, Mass. Inst. of Technology. Cambridge, Mass. W. E. C. EUSTIS, G. A. PACKARD. Columbia Holds four sessions during year. Annual meeting in September or October. W. H. LINNEY, Chairman. OSCAR LACHMUND, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash. STANLY A. EASTON, S. SHEDD. Puget Sound Meets second Saturday of each month SIMON H. ASH, Chairman. I. F. LAUCKS, Vice-Chairman. CHARLES SIMENSTAD, Secretary-Treasurer, 425 Lyon Bldg., Seattle, Wash. GLENVILLE A. COLLINS, JOHN N. POTT

Jan 6, 1917

By Donald Barton

THE theory of gravitation is based on Newton's law that any two bodies exert a mutual attraction which is proportional to the product of their masses and inversely proportional to the square of the distance between them; i. e., A = K MM/R2 (1) where K is a constant, M and m are the respective masses of the two bodies, and R the distance between them. In the earth's gravitational system, the earth is one of the bodies; the other may be any body within or without the earth. In theoretical discussions and calculations in regard to gravity, that other body usually is taken as a unit of mass: in the C. G. S. system, a body of one gram in mass. GRAVITY AND LEVEL SURFACES Gravity is defined in geophysics as the force of attraction exerted by the earth, towards itself, on a body of unit mass. The intensity of gravity is usually expressed in dynes of force or in centimeters of acceleration. In geophysical work in America; most commonly it is expressed in dynes (per gram) with the "per gram" understood and not directly expressed. In geophysical work in Europe, most commonly it is expressed in centimeters per second per second (cm./sec.2) and less commonly merely as centimeter-gram-second units (C. G. S.). At sea level, the intensity of gravity amounts very nearly to 980 dynes. The vertical is the direction along which the attraction of gravity is exerted at any point. In most cases, it is very nearly, but not quite, perpendicular to the earth's surface. The path that would be taken by a body falling freely through space toward the earth is vertical at each point and may be spoken of also as "the vertical," or as the line of the vertical, or as a line of force of gravity. At the earth's surface it commonly is very nearly, but not quite, a straight line.

Jan 1, 1928

By Donald Barton

THE theory of gravitation is based on Newton's law that any two bodies exert a mutual attraction which is proportional to the product of their masses and inversely proportional to the square of the distance between them; i. e., A = K MM/R2 (1) where K is a constant, M and m are the respective masses of the two bodies, and R the distance between them. In the earth's gravitational system, the earth is one of the bodies; the other may be any body within or without the earth. In theoretical discussions and calculations in regard to gravity, that other body usually is taken as a unit of mass: in the C. G. S. system, a body of one gram in mass. GRAVITY AND LEVEL SURFACES Gravity is defined in geophysics as the force of attraction exerted by the earth, towards itself, on a body of unit mass. The intensity of gravity is usually expressed in dynes of force or in centimeters of acceleration. In geophysical work in America, most commonly it is expressed in dynes (per gram) with the "per gram" understood and not directly expressed. In geophysical work in Europe, most commonly it is expressed in centimeters per second per second (cm./sec 2) and less commonly merely as centimeter-gram-second units (C. G. S.). At sea level, the intensity of gravity amounts very nearly to 980 dynes. The vertical is the direction along which the attraction of gravity is exerted at any point. In most cases, it is very nearly, but not quite, perpendicular to the earth's surface. The path that would be taken by a body falling freely through space toward the earth is vertical at each point and may be spoken of also as "the vertical," or as the line of the vertical, or as a line of force of gravity. At the earth's surface it commonly is very nearly, but not quite, a straight line.

Jan 1, 1928

By G. S. Rice, J. A. Davis

The Péchelbronn oil field is located in the province of Alsace, in the Rhine Valley, about 30 miles north of Strasbourg. It is approximately 4 miles wide and 12 miles long, extending from the villages of Lobsann on the north to Wintershausen and Ohlungen near Haguenau on the south. (See Fig. 1.) The productive area includes about 44,000 hectares (107,680 acres). The name Péchelbronn signifies "pitch-spring" or "pitch-fountain." The first exploratory galleries were driven in from the hillside in 1735; and in 1745 the first official concession was granted by the French government and the first pit sunk to a depth of about 30 ft. Extraction by drilled wells was begun in 1879, supplementing the mining operations, and during the next 10 years 200 wells were drilled to an average depth of 172 m. (568 ft.). The bringing in of two "gusher" wells, in 1882 and 1888, respectively, was followed by the abandonment of all underground work. Underground mining, with a view to increasing the production of petroleum by recovering the oil left in the sands after drilling wells, was resumed in 1916. This mining operation started by sinking shaft No. 1 to a depth of 150 m. (495 ft.). The underground developments were pushed during 1917 and 1918 and the annual production of the Péchel-bronn field was increased to about 50,000 metric tons or 350,000 bbl. On the signing of the Versailles Treaty the province of Alsace, which had been taken by Germany as the result of the war of 1870, was returned to France, and the proprietary rights were taken over by the French Government. Concessions or leases, which embraced all the known oil-bearing territory of the field, were granted to the present operating company, Mines de Péchelbronn. This company followed both the drilling and the mining methods of the previous company.

Jan 1, 1927

By Donald H. McLaughlin

MINERAL industry activities have not been seriously hampered by a lack of men with higher training. The balance between opportunities for employment and advancement and available personnel has been a happy one, with enough competition to stimulate effort but not the unfortunate conditions arising from an overabundance. of employment seekers. Nearly all mineral industry educational institutions have been concerned about the falling enrollment in mining and metallurgical courses of study during the past decade. But industry has drawn upon a supply of many types of technically trained men apart from those who prepared their careers specifically in the mineral industry. Some schools have made this possible by uniting geologists, mineralogists, and others with students in mining and engineering. On the other hand, some schools have combined their department of mining engineering with an over-all engineering department and continue to send their graduates into the mineral industry by another route. On the whole, this seems to be a good trend and is likely to result in men better trained for current problems than would have been possible under the older rigid curricula.

Jan 1, 1947

By H. M. Ziesemer, George Mieyr

Prior to 1909 that mountain of porphyry known as Sacramento Hill had hardly been touched though it had always been thought to contain ore. During that year, exploratory work was started by underground methods; drifting and raising continued until 1913. It was proved that a mineralized zone existed, the limits of which had not been determined ; so, because of the lower costs of exploratory work and the greater desirability of vertical sections, it was decided to prove the extent of the ore zone by churn drills. Drilling continued until 1917, when it seemed almost certain that the horizontal limits of the orebodies had been determined. Ore continued in depth in one direction beyond a point where it was economical to explore by churn drilling; this extension is still being developed by underground methods. The irregularities of the boundaries of the ore zones, together with the variable grades of ore encountered, made it necessary to drill on the corners of 100-ft. squares. Two ore zones were proved, known as the East and West Orebodies. The Sacramento Hill porphyry stock intruded into the Dividend fault. The fault ran roughly east and west with a dip to the south, having pre-Cambrian schists on the north against Paleozoic limestone on the south. This intrusion was accompanied by a silica breccia on the south periphery, along the limestone contact side. The ore lay in the silica breccia and in the porphyry, some distance from the breccia. NO ore was found in the heart of the porphyry mass on the north side, along the schist contact. The West Orebody is elliptic in shape, having a major axis of 1200 ft. (366 m.) and a minor axis of 800 ft. (244 m.); these diminish with depth until, at 300 ft., the axes are 500 ft. and 300 ft., respectively. The ore consists of chalcocite, some bornite, chalcopyrite, and considerable pyrite in a siliceous gangue. About 30 per cent. of the copper is caused by

Jan 1, 1923

By George Mieyr, H. M. Ziesemer

Prior to 1909 that mountain of porphyry known as Sacramento Hill had hardly been touched though it had always been thought to contain ore. During that year, exploratory work was started by underground methods; drifting and raising continued until 1913. It was proved that a mineralized zone existed, the limits of which had not been determined ; so, because of the lower costs of exploratory work and the greater desirability of vertical sections, it was decided to prove the extent of the ore zone by churn drills. Drilling continued until 1917, when it seemed almost certain that the horizontal limits of the orebodies had been determined. Ore continued in depth in one direction beyond a point where it was economical to explore by churn drilling; this extension is still being developed by underground methods. The irregularities of the boundaries of the ore zones, together with the variable grades of ore encountered, made it necessary to drill on the corners of 100-ft. squares. Two ore zones were proved, known as the East and West Orebodies. The Sacramento Hill porphyry stock intruded into the Dividend fault. The fault ran roughly east and west with a dip to the south, having pre-Cambrian schists on the north against Paleozoic limestone on the south. This intrusion was accompanied by a silica breccia on the south periphery, along the limestone contact side. The ore lay in the silica breccia and in the porphyry, some distance from the breccia. NO ore was found in the heart of the porphyry mass on the north side, along the schist contact. The West Orebody is elliptic in shape, having a major axis of 1200 ft. (366 m.) and a minor axis of 800 ft. (244 m.); these diminish with depth until, at 300 ft., the axes are 500 ft. and 300 ft., respectively. The ore consists of chalcocite, some bornite, chalcopyrite, and considerable pyrite in a siliceous gangue. About 30 per cent. of the copper is caused by

Jan 1, 1923