Search Documents

By James Ruddy

THE medical program of the Climax Molybdenum Co. is under the supervision of the department of industrial medicine of the University of Colorado, of which James J. Waring, professor of medicine at the University Medical School, is director. Dr. Waring is consultant and direct supervisor of both the hospital and industrial medical department at Climax. At Climax the program is in charge of the medical director and the associate physician, Dr. Galen M. Hover. The hospital at Climax is completely equipped with all that is necessary for the practice of scientific medicine and surgery. Only graduate registered nurses with experience in industrial medicine are employed. Being only a few hundred yards from the portal of the mine. acci-

Jan 1, 1946

By F. M. Waring

produced when zinc is substituted for a certain amount of tin are decidedly unsatisfactory. The substitution of aluminum for tin is entirely impractical, and such castings are worthless. This does not, however, exhaust all the possibilities of substituting other metals for tin in the copper-tin-lead alloys, but it is my opinion that the substitution of any other metals, in those alloys, can be made only by sacrificing the quality of the alloy. The possibility of substituting alloys of an entirely different type presents an attractive field for research. The copper-tin-lead alloy has attained its position as the most desirable bronze bearing alloy, but this does not mean that some other alloy may not be found which may give equally good or better results. In the search for such a substitute alloy it should be borne in mind that a bearing metal should possess the following properties: (1) It should be sufficiently rigid to support the load or resist the impact, but yet not so brittle that it will easily crack. (2) It should have as great a yielding or plastic nature as is consistent with its ability to support the load or resist the impact without deformation of the bearing as a whole. (3) The ideal structure combines a hard matrix to support the load and a softer metal or alloy contained within such matrix, to permit the bearing surface to adjust itself to irregularities of service. (4) It should be easy to handle in the foundry and machine shop. (5) It should be capable of being remelted without deterioration. (6) For use in babbitt-lined bearings, it should be capable of being tinned, so that the babbitt can be applied thereto. (7) It should have good heat conductivity in order to dissipate the heat generated by friction. Pennsylvania Railroad Anti-friction and Bell Metals F. M. Waring," Altoona, Pa.—Thc necessity for conserving tin has recently been very forcibly brought to the attention of all consumers, and efforts are now being made to reduce the tin content in certain alloys or to substitute other alloys not containing tin. The approximate composition of the non-ferrous alloys in general use on the Pennsylvania Railroad are given in the accompanying table. Phosphor bronze is used principally for rod bushings, main-rod brasses, and crosshead shoes. Ex. B bronze is used to a small extent for backs of car and coach bearings, but the majority of these are now made of the car-journal bronze, which contains, on the average, about 5 per cent. tin.

Jan 1, 1919

By C. R. Dodson, W. T. Cardwell

This paper presents the results of a theoretical and experimental study of the effect of preperforated liners on well productivity. The analysis concerns the rectangular type of slot, either machine or torch cut, which is common in California. Muskatla treated this problem recently in a mathematical analysis of the flow of oil or gas from natural reservoirs into both gun-perforated and slotted liners. This paper presents additional and simplified analytical considerations and conclusions for the slotted liner, the solutions being applicable in the laboratory as well as in the field. An application of the analytical methods to permeability measurements on mounted core samples is given, to show the effects of sealing wax or other obstructions on the end faces of the cores. Results Fig. I 'Ompares the results of some theoretical calculations with the results of electrical analogy experiments performed in the Standard Oil Company of California's Production Technology Laboratory at La Habra, California. Fig. I indicates that the flux into short, "three-dimensional slots" of the relative dimensions encountered in practice is approximately equal to that into full-length, "two-dimensional slots" having the same open fraction of pipe. (The same numbers of slot rows, and the same radius ratio are also implied.) It can be seen from physical considerations that the closeness of this approximation must improve as the ratio of the external radius to the internal radius increases. Therefore, it is possible to calculate the flow into a slotted liner using a simple modification of the Darcy equation: where N is .the number of slot rows and O is the open fraction of the pipe. Fig. 2 shows the results of calculations . using Eq. 28. The most remarkable features of Fig. 2 are the high flux values for very small open fractions of pipe. For instance, with six slot rows and a radius ratio of 500, 74 per cent of the open-hole flux may be obtained with only o.I per cent of pipe Open. Fig. 2 shows that for a given open frac tion of pipe, the flux is greater, the greater

Jan 1, 1945

Discovery of a hitherto unsuspected extension of the Vermilion range iron formation in Northern St. Louis County, Minn., has been announced by the director of the State's geological survey, Dr. George M. Schwartz. USGS aeromagnetic maps show that the Vermilion range curves southeast from the Tower-Soudan area into the wilderness between Embarrass and Bear Head Lake. Dr. Schwartz believes that this new information justifies considerable exploration and drilling for iron ore in an area of about 20 sq miles southeast of Soudan. The aerial maps were a result of a three year USGS-Minnesota Geological Survey aerial search for iron formations in a 30,000 sq mile area in northern Minnesota.

Jan 12, 1950

By L. C. Chang, T. A. Read

Diffusionless transformation in Au-Cd single crystals containing about 50 atomic pet Cd was investigated by means of X-ray analysis of the orientation relationships, electrical resistivity measurements, and motion picture studies of the movement of boundaries between the new and old phases during transformation. The nucleation of diffusionless transformation by imperfections and the generation of imperfections by diffusionless transformation were discussed. THAT connections exist between plastic deformation and diffusionless phase changes has long been recognized. Thus it is often possible to produce a diffusionless phase change in a temperature range, above that in which the change occurs spontaneously, by cold-working the initial phase. Certain aspects of the dislocation theory of the plastic deformation of crystalline solids also provide for a rather direct connection between the processes involved in plastic deformation and in diffusionless phase changes. Heidenreich and Shockleyl have pointed out that simple edge dislocations in f.c.c. metals are probably unstable, and that the more probable lattice imperfections, called extended edge dislocations, consist of two half dislocations separated by a distance of the order of magnitude of 100A. The region about two atomic planes thick between the half dislocations because of this stacking fault may be described as having the hexagonal close-packed structure. Presumably the stacking faults observed by Barrett" fter cold-working f.c.c. Cu-Si alloys resulted from the passage of such half dislocations through the lattice of the initial phase. It is now becoming clear that the development of a detailed theory of the atomic movements involved in diffusionless phase changes will require a consideration of the role played by lattice imperfections, just as such considerations are necessary to the understanding of plastic deformation mechanisms. This point of view has been recently set forth, for example, by Cohen, Machlin, and Paranjpe3 who pointed out the role which might be played by screw dislocations in nucleating diffusionless phase changes. The present paper reports on some aspects of the diffusionless phase change in single crystals of the beta phase alloy Au-Cd which serve to emphasize further the importance of lattice imperfections in diffusionless phase changes. The diffusionless phase change of Au-Cd possesses several remarkable features. One of these is that the interface between the high-temperature beta phase and the low-temperature orthorhombic phase typically moves with a low velocity, in contrast to the behavior observed in the transformation of austenite to martensite. Motion pictures of this slow interface motion have been prepared in the course of the work reported here. Another important feature of the Au-Cd transformation is the small amount of undercooling observed. The reverse transformation occurs on reheating to a temperature only 20" higher than the transformation temperature observed on cooling, and under some circumstances the hysteresis observed is substantially less than this. This narrow temperature range between transformation on heating and cooling is presumably in part a consequence of the fact that the transformation requires a lattice shear of only about 3". Finally, the orthorhombic product phase possesses unusual mechanical properties, as was first pointed out by olander' and Benedicks." After completion of the transformation on cooling the specimen can be severely deformed, yet on the release of load it springs back to its original shape in a rubber-like manner. Explanation of this phenomenon will require an understanding of the lattice imperfections in the orthorhombic structure and, correspondingly, of those in the initial body-centered cubic structure. Single crystals of Au-Cd alloy containing 47.5 and 49.0 atomic pct Cd were prepared from fine gold (99.95 pct purity) and chemically pure cadmium (99.99 pct purity) by melting the alloy in an evacuated and sealed fused quartz tubing and growing into single-crystal form by the Bridgman method. The Au-Cd alloy containing 47.5 atomic pct Cd undergoes a diffusionless transformation from an ordered body-centered cubic structure to an orthorhombic structure when it is cooled to about 60°C, while the reverse transformation takes place when the alloy is heated to about 80°C, according to electrical resistivity studies. The structures of these two phases have been studied by Blander,4 reinvestigated by Bystrom and Almin.e he lines of Debye photo-gram of powdered samples of Au-Cd alloy containing 47.5 atomic pct Cd prepared in this laboratory were identified and agreed fairly well with those of

Jan 1, 1952

ALABAMA. Aldrich, Aldrich, W. F. Anniston, Noble, A. E. Auburn,' Brown, R. L. Bessemer Abbott, C. E., Ferguson, V., Williams, E. P. Birmingham, Aldrich, T. H., Aldrich, T. H., Jr., Allen, A. W., Bowron, J., Burbidge, T. A., Crawford, G. G, Crockard, F. H., Dimmick, F. D., Ellis, E.,E., Hiller, E., Johnson, G. R., Ludwig, C. P., McCormack, G B., McCrery, Moffett, C. A., Morris, B.H, Peters, R., Jr., Pill, J. R., Ramsay, E. Gadsden, Hudson, J. B. Helena, Squire, J. Holt, Shook, J. W. Huntsville, Moss. Lehigh, Toulmin. Rock Run, Garvin, J. M. Thomas, Kluttz, W. L., Johnson, J. E., Jr. University, Litchman, H. B., Smith, E. A. Woodward, Woodward, A. H.

Jan 1, 1910

By F. M., Waring

F. M. WARING,* Altoona, Pa.-The necessity for conserving tin has recently been very forcibly brought to the attention of all consumers, and efforts are now being made to reduce the tin content in certain alloys or to substitute other alloys not containing tin. The approximate composition of the non-ferrous alloys in general use on the Pennsylvania Railroad are given in the accompanying table. Phosphor bronze is used principally for rod bushings, main-rod brasses, and crosshead shoes. Ex. B bronze is used to a small extent for backs of car and coach bearings, but the majority of these are now made of the car-journal bronze, which contains, on the average, about 5 per cent. tin.

Jan 12, 1918

By B. W. Vallat

(San Francisco Meeting, October, 1911.) THE Newport mine, located at Ironwood, Gogebic county, Mich., on the Gogebic iron-range, is owned and operated by the Newport Mining Co., for the mining of iron-ore. I. GEOLOGY. The general geology of the Gogebic range has been determined and recorded at different times by well-known geologists,) and their work will be referred to briefly in connection with the local conditions in the mine. The strike of the formation across this property is about 15° north of east. The, general dip is 68° to the north. At the base of the formation on the south lies the granite. Looking north, at right angles to the strike of the formation, we have the foot-wall of quartz-slates and quartzite about 400 ft. wide; the iron-formation about 800 ft. wide, and the hanging-wall of black slates. The iron-formation is composed of banded jasper and quartzite together with iron oxide and concentrations of iron-ore. In character the ore is a soft red hematite, with occasional masses of hard blue "steel ore." The formation is crossed in many places by diorite dikes, which cut through at various angles, the larger or main dikes dipping into the foot-wall in a SE. direction at angles varying from 15° to 30°, while numerous small dikes occur which strike through the formation in a vertical plane and at approximately right angles to the main dikes. There are various theories concerning these dikes, especially as to the time of their origin with relation to the ore-deposition. The commonly-accepted theory is that the dikes were there first, but there are some who contend that they were formed

Nov 1, 1911

By K. O. Stamm, B. A. Rogers

Because it is the basis of the economically important operation of hardening steel by quenching, the A3 transformation in iron has been the subject of numerous investigations. Although the contributions to this subject are interesting, no general review will be given here. Readers who care to follow the matter further are referred to the comprehensive summary by Cleaves and Thompson,l which covers the literature to about 1935. Their references to 53 papers on the subject suggest that further investigation is hardly justifiable. However, considerable interest has devel oped recently concerning the reversibility of the transformation. From thermo-dynamic considerations, the transition ought to occur at the same point on heating or cooling, if the change of temperature is sufficiently slow. Yet all of the earlier investigators found a difference of several degrees. Burgess and Crowe,2 who used thermal methods, obtained average temperatures of 912" for Ac3 and 900°C. for Ar3 on electrolytic iron. Their data indicate a considerable range of temperature over which the change occurs, both on heating and on cooling. Terry3 measured the susceptibility in the critical range and estimated from the steepest parts of his curves that Ac3 came at 9I8° and Ar3 at 903°C. Ishiwara4 was one of the first investigators to report a shorter interval between the temperature of the change in the two directions. He measured the change of susceptibility of kaolin-coated samples of steel, in a hydrogen atmosphere, at rater of heating and cooling so low that about 3 or 4 hr. were required for the transformation to complete itself. His results show some variability between samples, but indicate that the difference between Ac3 and Ar3 is in the vicinity of 6°C. Roberts and Davey5 measured the space lattice in pure iron in the vicinity of 900°C. and concluded that a change occurs reversibly between 907' 3" and 910" 3°C., probably between 907" and 910°C. Wells, Ackley, and Meh16 made dilatometric determinations of the Ac3 and Ar3 points in samples of hydrogen-treated carbonyl iron maintained under a vacuum. They used three rates of heating and cooling: 2°, ½°, and .?°C. per min. and found the spread between the two points decreased with low rates. At the slowest rate, the Ac3 transition occurred at 909° to 909. 5°C. and the Ar3 change at 907°C. in three of the samples believed to contain the lowest percentages of alien elements. They concluded that if the rate of temperature change and the content of alien eiements were low enough, the A3 transformation would be completely reversible at 909.50 + 1°C. The question of reversibility is an interesting one and when some iron with especially small percentages of alien elements became available the opportunity to conduct an investigation was welcomed. This iron was prepared by the Division of

Jan 1, 1942

By B. A. Rogers, K. O. Stamm

Because it is the basis of the economically important operation of hardening steel by quenching, the A3 transformation in iron has been the subject of numerous investigations. Although the contributions to this subject are interesting, no general review will be given here. Readers who care to follow the matter further are referred to the comprehensive summary by Cleaves and Thompson,l which covers the literature to about 1935. Their references to 53 papers on the subject suggest that further investigation is hardly justifiable. However, considerable interest has devel oped recently concerning the reversibility of the transformation. From thermo-dynamic considerations, the transition ought to occur at the same point on heating or cooling, if the change of temperature is sufficiently slow. Yet all of the earlier investigators found a difference of several degrees. Burgess and Crowe,2 who used thermal methods, obtained average temperatures of 912" for Ac3 and 900°C. for Ar3 on electrolytic iron. Their data indicate a considerable range of temperature over which the change occurs, both on heating and on cooling. Terry3 measured the susceptibility in the critical range and estimated from the steepest parts of his curves that Ac3 came at 9I8° and Ar3 at 903°C. Ishiwara4 was one of the first investigators to report a shorter interval between the temperature of the change in the two directions. He measured the change of susceptibility of kaolin-coated samples of steel, in a hydrogen atmosphere, at rater of heating and cooling so low that about 3 or 4 hr. were required for the transformation to complete itself. His results show some variability between samples, but indicate that the difference between Ac3 and Ar3 is in the vicinity of 6°C. Roberts and Davey5 measured the space lattice in pure iron in the vicinity of 900°C. and concluded that a change occurs reversibly between 907' 3" and 910" 3°C., probably between 907" and 910°C. Wells, Ackley, and Meh16 made dilatometric determinations of the Ac3 and Ar3 points in samples of hydrogen-treated carbonyl iron maintained under a vacuum. They used three rates of heating and cooling: 2°, ½°, and .?°C. per min. and found the spread between the two points decreased with low rates. At the slowest rate, the Ac3 transition occurred at 909° to 909. 5°C. and the Ar3 change at 907°C. in three of the samples believed to contain the lowest percentages of alien elements. They concluded that if the rate of temperature change and the content of alien eiements were low enough, the A3 transformation would be completely reversible at 909.50 + 1°C. The question of reversibility is an interesting one and when some iron with especially small percentages of alien elements became available the opportunity to conduct an investigation was welcomed. This iron was prepared by the Division of

Jan 1, 1942

By B. A. Rogers, K. O. Stamm

BECAUSE it is the basis of the economically important operation of hardening steel by quenching, the A3 transformation in iron has been the subject of numerous investigations. Although the contributions to this subject are interesting, no general review will be given here. Readers who care to follow the matter further are referred to the comprehensive summary by Cleaves and Thompson,1 which covers the literature to about 1935. Their references to 53 papers on the subject suggest that further investigation is hardly justifiable. However, considerable interest has developed recently concerning the reversibility of the transformation. From thermodynamic considerations, the transition ought to occur at the same point on heating or cooling, if the change of temperature is sufficiently slow. Yet all of the earlier investigators found a difference of several degrees. Burgess and Crowe,2 who used thermal methods, obtained average temperatures of 912° for Ac3 and 900°C. for Ar3 on electrolytic iron. Their data indicate a considerable range of temperature over which the change occurs, both on heating and on cooling. Terry3 measured the susceptibility in the critical range and estimated from the steepest parts of his curves that Ac3 came at 9180 and Ar3 at 903°C. Ishiwara4 was one of the first investigators to report a shorter interval between the temperature of the change in the two directions. He measured the change of susceptibility of kaolin-coated samples of steel, in a hydrogen atmosphere, at rates of heating and cooling so low that about 3 or 4 hr. were required for the transformation to complete itself. His results show some variability between samples, but indicate that the difference between Ac3 and Ar3 is in the vicinity of 6°C. Roberts and Davey5 measured the space lattice in pure iron in the vicinity of 900°°C. and concluded that a change occurs reversibly between 907° ± 3° and 9100 ± 3°C., probably between 907° and 910°C. Wells, Ackley, and Mehl6 made dilatometric determinations of the Ac3 and Ar3 points in samples of hydrogen-treated carbonyl iron maintained under a vacuum. They used three rates of heating and cooling: 2°, '1/2°, and 1/8°C. per min. and found the spread between the two points decreased with low rates. At the slowest rate, the Ac3 transition occurred at 909° to 909.5°C. and the Ar3 change at 907°C. in three of the samples believed to contain the lowest percentages of alien elements. They concluded that if the rate of temperature change and the content of alien elements were low enough, the A3 transformation would be completely reversible at 909.5° ± I°C. The question of reversibility is an interesting one and when some iron with especially small percentages of alien elements became available the opportunity to conduct an investigation was welcomed. This iron was prepared by the Division of

Jan 1, 1941

By Roswell Johnson

THE prevailing system of wells on a rectangular basis, as shown in Fig. 1-A, has developed because of the exigencies of offsetting at boundary lines. When, however, a very large tract is, being drilled, it is often possible to abandon this inferior method for the superior arrangement C- PROPER STAGGERING FIG. 1.-THREE SYSTEMS OF SPACING WELLS. known as "staggering," which is illustrated in Fig. 1, B and C. The advantages of the triangular over the rectangular method are evident from Fig. 2, computed on the basis of one well to 10 acres (4 ha.). With the triangular system, no land is more than 409.4 ft. (124.8 m.) from a

Jan 8, 1918

By Adrian C. Dorenfeld

Concentradora "Doña Aida" (100 t /d capacity) was built in 1971-72 to treat dumps and ores containing mixed oxide-sulfide copper-gold-silver minerals derived from two veins. The veins, Don Felipe and Maria, are about 150 m apart, but are distinctly different mineralogically. The deposits are near Sun Juan de Guadalupe, Durango, Mexico. All new process equipment was manufactured locally, in or near Torreon, Coahuilu. Sampling, ore testing, flowsheet design, plant design, drawings, purchasing, financing, and construction, etc., were planned and directed by two engineers. Construction was executed by local miners and common labor (largely agricultural). The paper presents detailed costs for equipment and construction. The subsequent breaking-in operation is discussed.

Jan 1, 1982

Some Things We Don't Know about the Creep of Metals. By H. W. Gillett (T.P. 1087) Reduction of Iron Ores under Pressure by Hydrogen. By Michael Tenenbaum and T. L. Joseph (T.P. loll, with discussion) Induction Furnaces for Rotating Liquid Crucibles. By E. P. Barrett, W. F. Hol- bRook and C. E. Wood (T.P. 986, with discussion) Mechanism of Solidification and Segregation in a Low-carbon Rimming-steel Ingot,. By Anson Hayes and John Chipman (T.P. 988, with discussion) Solidification of Rimming-steel Ingots. By A. HultGRen and G. PhRagmen. (Contribution 112) Dendritic Structure of Some Alloy Steels. By Daniel .I. Martin and James L. Martin (T.P. 1066, with discussion) Occlusion and Evolution of Hydrogen by Pure Iron. By George A. Moore and Donald P. Smith (T.P. 1065, with discussion) Structure of Iron after Con~pression. Hy Charles S. Barrett (T.P. 977, with discussion) Structure of Iron after Drawing, Swaging, and Elongating in Tension. Ry Charles S. Barrett and L. H. LevensoN (T.P. 1038, with discussion) Magnetic Torque Studies of the Texture of Cold-rolled and of Recrystallized Iron-silicon Alloys. By Leo P. TaraSovJ(T.P. 1012, with discussion) Influence of Atmosphere and Pressure on Structure of Iron-carbon-silicon Alloys. By Alfred Boyles (T.P. 1046) Kinetics of the Decomposition of Austenite at Constant Temperature. By J. H. Austin and R. L. Rickett (T.P. 964, with discussion) Reaction Kinctics in Processes of Nucleation and Growth. By William A. Johnson and Robert F. Mehl (T.P. 1089, with discussion) Phase Changes in 3.5 Per Cent Nickel Steel in the Acl Region. By I. N. Bavarine (T.P. 1031, with discussion) Chromium in Structural Steel. By Walter Crafts (T.P. 1055) Surface Allotropic Transformation in Stainless Steel Induced by Polishing. By J. T. BuHwell and J. WUlff (T.P. 1032, with discussion) Nature of :Passivity in Stainless Steels and Other Alloys, I and 11. Ry H. H. Uhlig and John WUlff (T.P. 1050, with discussion) Thermal Expansion of Nickel-iron Alloys (Nickel from 30 to 70 Per Cent). Ry J. M. Lohr and Charles H. Hopkins (T.P. 987, with discussion) Low-temperature Transformation in Iron-nickel-cobalt Alloys. By L. L. Wy~Ian (T.P. 1013, with discussion) Fracture of Steels at Elevated Temperatures after Prolonged Loading. By R. H. Thielemann and E. R. Parker (T.P. 1034, with discussion)

Jan 1, 1939

Some Things We Don't Know about the Creep of Metals. By H. W. Gillett (T.P. 1087) Reduction of Iron Ores under Pressure by Hydrogen. By Michael Tenenbaum and T. L. Joseph (T.P. loll, with discussion) Induction Furnaces for Rotating Liquid Crucibles. By E. P. Barrett, W. F. Hol- bRook and C. E. Wood (T.P. 986, with discussion) Mechanism of Solidification and Segregation in a Low-carbon Rimming-steel Ingot,. By Anson Hayes and John Chipman (T.P. 988, with discussion) Solidification of Rimming-steel Ingots. By A. HultGRen and G. PhRagmen. (Contribution 112) Dendritic Structure of Some Alloy Steels. By Daniel .I. Martin and James L. Martin (T.P. 1066, with discussion) Occlusion and Evolution of Hydrogen by Pure Iron. By George A. Moore and Donald P. Smith (T.P. 1065, with discussion) Structure of Iron after Con~pression. Hy Charles S. Barrett (T.P. 977, with discussion) Structure of Iron after Drawing, Swaging, and Elongating in Tension. Ry Charles S. Barrett and L. H. LevensoN (T.P. 1038, with discussion) Magnetic Torque Studies of the Texture of Cold-rolled and of Recrystallized Iron-silicon Alloys. By Leo P. TaraSovJ(T.P. 1012, with discussion) Influence of Atmosphere and Pressure on Structure of Iron-carbon-silicon Alloys. By Alfred Boyles (T.P. 1046) Kinetics of the Decomposition of Austenite at Constant Temperature. By J. H. Austin and R. L. Rickett (T.P. 964, with discussion) Reaction Kinctics in Processes of Nucleation and Growth. By William A. Johnson and Robert F. Mehl (T.P. 1089, with discussion) Phase Changes in 3.5 Per Cent Nickel Steel in the Acl Region. By I. N. Bavarine (T.P. 1031, with discussion) Chromium in Structural Steel. By Walter Crafts (T.P. 1055) Surface Allotropic Transformation in Stainless Steel Induced by Polishing. By J. T. BuHwell and J. WUlff (T.P. 1032, with discussion) Nature of :Passivity in Stainless Steels and Other Alloys, I and 11. Ry H. H. Uhlig and John WUlff (T.P. 1050, with discussion) Thermal Expansion of Nickel-iron Alloys (Nickel from 30 to 70 Per Cent). Ry J. M. Lohr and Charles H. Hopkins (T.P. 987, with discussion) Low-temperature Transformation in Iron-nickel-cobalt Alloys. By L. L. Wy~Ian (T.P. 1013, with discussion) Fracture of Steels at Elevated Temperatures after Prolonged Loading. By R. H. Thielemann and E. R. Parker (T.P. 1034, with discussion)

Jan 1, 1939

By P. F. Gnirk, J. B. Cheatham

Single bit-tooth penetration experiments under static load were conducted on six rocks at confining pressures of O to 5,000 psi using sharp wedge-shaped teeth with included angles ranging from 30 to 120° In general, the force-displacement curves for all rocks exhibit an increasingly nonlinear and discontinuous behavior with decreasing confining pressure. The confining pressure at which a rock exhibits a macroscopic transition from predominantly ductile to predominantly brittle behavior during penetration vmies from about 500 to 1,000 psi for the limestones to greater than 5,000 psi for dolomite. The correlation between calculated values of force per unit penetration based on plasticity theory and experimental values is quite encouraging, even at confining pressures as low as 1,000 psi A qualitative correlation between volume of fragmented rock per unit energy input for a single bit-tooth and drilling rate for microbits appears to exist over a confining pressure range of 0 to 5,000 psi. INTRODUCTION Laboratory experiments utilizing a small-scale drilling apparatus have demonstrated that penetration rates are reduced considerably as a result of increasing the confining pressure from atmospheric to a few thousand psi?-3 This undesirable situation can, in general, be attributed to a combination of decreased efficiency of chip removal at the bottom of the borehole, increased rock-failure strength, and a possible change in the mechanism of chip generation and rock fragmentation with increasing confining pressure. To more fully understand the principles underlying the last circumstance, it is the purpose of this investigation to experimentally study the mechanism of single bit-tooth penetration into dry rock at low confining pressures and, in particular, to establish the confining pressure at which the penetration mechanism may undergo a brittle to ductile transition for various rock types commonly encountered in drilling. Confining pressure as used here refers to the differential pressure between the borehole fluid pressure and the formation-pore fluid pressure. EXPERIMENTAL PROCEDURE Using an experimental apparatus previously described: a single, sharp wedge-shaped tool was forced under a "statically" applied load into an effectively semi-in finite dry rock sample subjected to a prescribed confining pressure. To prevent the invasion of the con fining-pressure fluid into the pores of the rock sample during penetration, the exposed surface of the rock was jacketed with a layer of silicon putty.* Electrical instrumentation incorporated into the apparatus yielded a graphical plot of force on the tool as a function of penetration or displacement of the tool into the rock during an experiment. During the course of the experimentation the following conditions were maintained constant: (1) pore pressure — atmospheric (i.e., the rock was dry); (2) temperature — 75F; (3) rate of loading — essentially static (approximately 0.002 in./sec); (4) bit tooth — a sharp wedge-shaped tool loaded normal to the rock surface; (5) rock surface — smooth and flat; (6) drilling fluid — hydraulic oil; and (7) maximum depth of penetration — approximateiy 0.1 in. In addition, each experiment was performed on a different rock sample so the rock surface is free of a layer of cuttings and of any previous indentation craters. The influence of the corners of a borehole was neglected, since each rock sample was cemented inta a section of aLuminum tubing to simulate a semi-infinite body. Indentation experiments were made on a sandstone, two limestones, a marble, a dolomite and a schist with a 60' bit-tooth over a range of confining pressures from atmospheric to 5,000 psi and at a constant confining pressure of 1,000 psi for a variety of bit-teeth with angles ranging from 30 to

Jan 1, 1966

New York Meets first Wednesday after first Tuesday of each month. J. E. JOHNSON, Jr., Chairman EDGAR RICKARD; Vice-Chairman D. M LIDDELL, Secretary, 7 Wall St., New York, N. Y. C. A. BORN, Treasurer JOHN V. N. DORR - LEWIS W. FRANCIS Boston Meets first Monday of each winter month. R. L. AGASSIZ, Chairman JAMES G. CARLETON, Vice-Chairman E. E. BUGBEE Secretary-Treasurer, -Mass. Inst. of Technology. Cambridge, Mass. W. E. C. EUSTIS G. A. PACKARD Columbia Holds four sessions during year. Annual meeting in September or October. W. H. LINNEY, Chairman OSCAR LACHMUND. Vice-Chairman LYNDON K. ARMSTRONG, Secretary-Treasurer, P. 0. Drawer 2154, Spokane, Wash. STANLY A. EASTON S. SHEDD

Jan 1, 1918

By L. V. Pirela, S. M. Farouq Ali

Some interest has been expressed recently in the application of solvents in conjunction with a thermal drive, such as a steamflood. At least one field project of this type has been reported. This paper makes the first attempt to provide some of the basic information necessary for choosing a solvent for such an application. Results of displacements conducted at elevated temperatures are also discussed. This paper shows that, in the case of alcohol-hydrocarbon-water or brine ternary systems, the system miscibility may increase, decrease, or both increase and decrease within the same system when the temperature increases. The distribution coefficient was consistently found to increase in favor of the oleic phase with an increase in temperature, which is advantageous from the standpoint of oil recovery. Results of solvent displacements in a sandstone core showed that even a relatively small temperature effect in the favorable direction (increase in miscibility and distribution coefficient) can lead to a 50 percent increase in oil recovery. On the other hand, if the system miscibility decreases with the temperature, even though the distribution coefficient increases, the oil recovery at the higher temperature may not increase. INTRODUCTION Miscible displacement has been the subject of many investigations. Miscible-phase solvent flooding, employing solvents such as alcohols that are miscible with both oil and water, has received considerable attention. Investigations conducted by Gatlin and Slobod,l Taber, Kamath and Reed,2 Holm and Csaszar,3 and Farouq Ali and Stah14 have helped in understanding the mechanism of solvent flooding. While the use of alcohols and similar solvents as oil recovery agents is economically unattractive, these solvents nevertheless provide a means of understanding the mechanistic aspects of important miscible-phase oil recovery processes such as the Maraflood process (discussed by Gogarty5). As shown by Taber et a1.,2 the phase behavior of a solvent-oil-water system is of .utmost importance in determining the efficiency of the oil displacement. This paper makes the first attempt to obtain the ternary phase behavior data for nine alcohol-hydrocarbon-water/brine systems at elevated temperatures. Results of core tests at elevated temperatures are also presented which corroborate the effect of temperature on oil recovery, as judged on the basis of phase-behavior data. The use of solvents at elevated temperatures has been suggested earlier by Farouq Ali.6 At least one field test of this type has been reportedO7 With the widespread use of thermal recovery techniques, it is possible in some situations (especially in steamflooding) that the use of a suitable solvent in conjunction with the heat carrier may be economically feasible. This paper attempts to provide some of the basic information needed for judging such feasibility. LOCATION OF THE PLAIT POINT The phase behavior of a typical ternary system consisting of a solvent, hydrocarbon and brine (or water) can be represented by a triangular diagram such as the one shown in Fig. 1 (for temperature TI). Point Pon the binodal curve represents the plait point, being the limit of tie lines such as Y1 Y2 The compositions of the coexisting oleic and aqueous phases are given by points Y2 and Y1, respectively, for any mixture composition along Y1Y2. The characteristics of ternary diagrams have been discussed by Findlay8 and others. Taber et aL3 have shown that the position of the plait point in a particular ternary system plays the decisive role in determining whether or not theoleic phase would be displaced in a continuous manner during an alcohol displacement. The area above the binodal curve also is important, since it represents

Jan 1, 1969

By A. C. Rubel

WHAT does management expect of W and from an engineer? First and foremost, it expects that he should become, and therefore should fit himself in every way to be, a part of management so that he may assume as much and as many of the responsibilities of management as his ability and the opportunities of the job permit. Let me make clear at the start that the profession of pure, technical engineering offers but limited opportunities at the top levels because of the inherent organization of engineering work. The line of succession to top jobs may be likened to a cone with a broad base and an extremely sharp point. Consider any oil company, large or small, or any operating function of that company, and you will find few top engineering jobs in the organization. This is true by the nature of the work handled. There will be a few district engineers depending on the spread of operations, a chief petroleum and production engineer, perhaps a few research engineers, possibly some technical executive assistants, and that is usually all. The road to these jobs is a long one and the competition is tough. The larger the organization the greater the opportunity, but always the ratio of engineers to top engineering jobs is only a small one.

Jan 1, 1947

W. M. CORSE, Mansfield, .Ohio.-We have sometimes seen in indi-vidual tests ultimate tensile strengths ass high as 55,000 lb. per. sq. in. being attained under electric furnace practice. These results, of course, average much lower than that, but with better methods of melting, can we hope to get the strength up to somewhere near the figure attained by these individual tests? C. P. KARR.--Yes, because with the electric furnace you can lessen the oxidation by means of the impurities always found in the melting. But one of the most important things in making 88-10-2 bronze of this class is to use a core-sand mold with a very open grain, so that the

Jan 12, 1919