Search Documents

By C. W. Allen, B. D. Cullity, H. S. Choi

The torsional deformation of aluminum and magnesium crystals is investigated, with particular reference to the dependence of proportional limit on crystal orientation. The proportional limit is found to be governed by the average value of the resolved shear stress on the most highly stressed slip systems, but the proportional limit does not strictly obey a critical-resolved-shear-stress law. The behavior of a cylindrical single crystal stressed in tension is well known: plastic flow begins when the resolved shear stress on the most highly stressed slip system reaches a critical value. There is much less understanding of the effect of torsion on such a crystal and on the way in which the critical-resolved-shear-stress law should be applied to torsional deformation. In the present paper particular attention is paid to the dependence of plastic yielding on crystal orientation and lesser attention to the mechanism of flow after yielding has occurred. New work on aluminum and magnesium crystals is presented, and previous results obtained in this laboratory on magnesium1 are re-examined. STRESS DISTRIBUTION The problems involved in torsional deformation of single crystals are due entirely to the complexity of the stress distribution. In tension, if loading conditions are perfect, the shear stress on any particular slip plane is completely uniform over the entire area of that plane. In torsion, on the other hand, the stress on any selected plane in a particular direction varies not only from center to edge of the specimen but also around its perimeter. It is convenient to express the stress at any point in terms of t0, which is the shear stress acting at the surface of a cylindrical specimen on a plane normal to the axis and in a direction tangential to the cylinder. At point P of Fig. 1 this stress acts in the direction of axis 2 and is given by To = 2T/pr3 [1] where T is the applied torque and r the specimen radius. This stress can be resolved on any chosen slip system, and details are given in the Appendix. Let P be the point on the specimen surface where the stress is to be evaluated; P is defined by its angular distance A from an arbitrary reference line through 0 normal to the axis. his line is usually taken as the direction of incidence of the X-ray beam used to determine the crystal orientation.) Then the shear stress t, acting at P in direction Dona plane whose normal is N is given by Ts/TO = sin ? 0, cos ?d sin (?0, - ?) + cos ?, sin ?d sin (?d - ?) [2] where 0, and Od are the angles between N and D, respectively, and the axis, ?0 and ?d are the angles between the projections of N and D, respectively, on the transverse plane and the reference line through 0. By means of Eq. [2], the stress 7, acting in any given slip direction can be computed. In the previous work on magnesium1 only gross slip tangential to the specimen surface was considered, and this

Jan 1, 1963

By G. W. Tower

THE YEAR 1931 was for most American copper producers one of restricted output but extremely low production cost.. When compared with 1929, the marked reductions in costs achieved in 1931, operating at rates in many instances a third to a half of capacity, can only be regarded as remarkable. In fact, the recent shut-down of several large operations suggests the probability that 1931 costs represent a bare minimum for many properties. Before discussing the 1931 results a few remarks on cost data are appropriate. The type of cost tabulation here presented was first published in 1929, (A. B. Parsons. E. & M. I. June 8, 1929), and has appeared each, succeeding year following in general the calculation method and company set-up of the original article. (. G. W. Tower, E. & III. L, July 8. 1930; S. D. Strauss, E. & M. J.; July 27, 1931). As far as possible the leading American copper companies are included. In considering these cost tabulations it must be borne in mind that the information from which they have been prepared is entirely contained in the annual report of each company; and that a multiplicity of interests and a condensed income statement for some of the larger companies, such as Cerro de Pasco and Kennecott, make the cost figure an arbitrary one depending upon sundry metal credits, metal products, miscellaneous income, etc. For Granby, Howe Sound. Magma, and Noranda, sundry metal credits are important. Furthermore Andes, Chile and Greene Cananea give costs only against copper sold. Although the individual costs here figured are by no means absolute they are computed by the same method each year and offer a basis of annual comparison; and with attention to footnotes the premises on which the costs are based may be easily followed.

Jan 1, 1932

By R. L. Stephenson

The effect of fabrication variables on the creep-rupture properties of TZM (Mo-0.5 pct Ti-0.08 pct Zr-0.03 pct C), Cb-TZM [columbium-modified TZM (7140-1.5 pct Nb-0.5 pct Ti-0.8 pct Zr-0.05 pct C)], and TZC (Mo-1.2 pct Ti-0.25 pct Zr-0.15 pct C) has been studied at 982º. 1093º, 1204º, and 1315°C for rupture times up to 1000 hr. The creep tests were performed in vacuum creep furnaces, employing cold-trapped oil-diffusion pumps, operating at pressures 2 X 10-7 tory. After-test chemical analyses showed no significant changes in interstitial content. The creep-rupture properties of TZM, fabricated according to current mill practice, were determined in the stress-relieved and in the re crystallized conditions to provide control data. Specimens of TZM, Cb-TZM, and TZC fabricated according to each of two experimental fabrication schedules were then tested. The schedules differed in terms of in-process annealing temperatures and warm -working temperatures. The data make several conclusions evident. Fabrication variables do indeed have a profound effect on the long-time creep-rupture properties of molybdenum alloys. Strengths of these alloys compare very favorably with those of other refractory metal alloys in the temperature range studied. FOR several years we have been engaged in the evaluation of the creep-rupture properties of promising refractory metal alloys. We consider the determination of these properties to 1000 hr at several temperatures necessary for a valid comparison. Such an evaluation indicated that the creep strengths of Mo-0.5 pct Ti and TZM (Mo-0.5 pct Ti-0.08 pct Zr-0.03 pct C) compare favorably with those of other refractory metal alloys. Tensile and recrystallization data of other investigators1,2 show an effect of fabrication variables. More specifically, those fabrication schedules which produce high strength through work hardening exhibit the least thermal stability. A similar conclusion was reported by perkins3 for Cb-TZM. This would lead one to expect that, in terms of creep, those materials showing higher strength at short times and low temperatures would exhibit lower strength at long times and high temperatures. If these expectations were fact, a substantial improvement could be made in these alloys by optimizing their fabrication schedule in terms of their anticipated service temperature. We therefore undertook a study of the effect of fabrication variables on the long-time creep properties of TZM, Cb-TZM (Mo-1.5 pct Cb-0.5 pct Ti-0.08 pct Zr-0.05pct C) and TZC (Mo-1.2 pct Ti-0.25 pct Zr-0.15 pct C). MATERIALS All materials used were supplied by the Climax Molybdenum Co. of Mich. Our original intention was to test the same heat of each alloy in different conditions. Fabrication difficulties prevented this; however, heats with nearly identical analysis were selected. The compositions of the materials used are listed in Table I. All materials were supplied in the

Jan 1, 1970

By Ali M. Heidarieh Zadeh, Raghu N. Singh

The paper presents a stability investigation of shaft intersections and pit bottom roadways in the vicinity of upcast and downcast shafts at a colliery in the U.K. Aschemeof instrumentation was aimed at monitoring the strata displacement surrounding the pit bottom roadways and shaft intersections with a view to ascertaining the origin of the strata movement and effectiveness of the control measures. The bore- hole instrumentation results together with a theoretical analysis suggested that the cause of instability could be attributed to the drivage of a roadway within the shaft pillar. A semi-empirical technique was used to calculate the amount of support resistance required to reinforce the pillar to take additional abutment load. A rock bolting system was designed to provide a required increase in thrust capacity of the roadway support. The results indicated that roadway closure was effectively controlled after installation of bolts indicating efficacy of the control measures adopted.

Jan 1, 1982

By N. Mungan

Laboratory water floods were performed in oil-wet and waterwet alundum and Torpedo cores, displacing a refined oil with n-hexylamine or Triton X-100 solution. Also, some floods were performed in which a sucrose solution was displaced with n-butyl alcohol. The Purpose ot the tests was to see if the oil recotlery could be increased and to examine what role the inter-facial tension reduction and wettability change play in the recovery mechanism. it was found that the chromatographic transport of amine was influenced by core wettability. In oil-wet cores, the rate of advance of the amine band could be predicted from equilibrium chromato-graphy, while in water-wet cores the amine band moved faster than predicted, indicating a non-equilibrium process. By reducing the interfacial tension to 1.1 dyne/ cm, oil recovery was increased. More oil was recovered from Dri-filmed cores than from water-wet cores. Reversing the wettability of the porous media from oil-wet condition also resulted in some additional oil recovery. Neutral wettability floods did not increase oil recovery. INTRODUCTION Interfacial forces in petroleum reservoirs are responsible for retention of large quantities of residual oil. Increasing exploration costs have created an incentive to attempt recovery of this residual oil by new and novel processes. One novel process involves changing the interfacial forces by introducing a chemical into the reservoir during water flooding. Recently, several investigators have carried out laboratory displacement tests using amines. lt3.4 The amines adsorbed onto initially water-wet core surfaces, changing them to oil wet. Additional oil was recovered when the cores were flooded in a manner reversing the. wettability from oil-wet conditions. In all these studies, the wettability reversal was considered responsible for increased oil recoveries although it was noted that amines also reduced oil-water interfacial tension. In the present study, displacement experiments were performed in water-wet and Dri-filmed cores. The purpose was to separate the effects of lowering the interfacial tension from changing the wettability. LABORATORY STUDY All experimental data given in this paper have been obtained at a temperature of 70F + 1 and prevailing atmospheric pressure. FLUIDS AND MATERIALS The oil used in these experiments* was washed with H2S04 and passed through two 100-200 mesh silica-gel beds to remove unsaturates and surface active impurities. Normal hexylamine** of practical purity was used, and the alundum cores*** were composed of nearly pure A1203. Fused quartz (SiOi) and Lucalox (A12 )t plates were used in the contact angle measurements. DISPLACEMENT TESTS Displacement tests were performed in alundum and Torpedo cores. Before displacement runs, cores were acidized with 0.1 normal HCI, flushed with distilled water and fired at 1,200F to make them water wet. This procedure also reduced water sensitivity of the Torpedo cores. Oil-wet cores were prepared from water-wet cores by flowing several pore volumes of 1 per cent by weight Dri-film SC-87 solution in heptane through the cores, flushing the cores with nitrogen, evacuating, and finally heating the cores at 300F for 4 or 5 hours. Between floods, cores were cleaned by conventional procedures and treated again as above.

Jan 1, 1965

By P. W. Bennett, E. M. Elkin

A new technique for the recovery of palladium and platinum and sludge from go12 electrolyte eliminates many of the drawbacks of the zinc-dust cementation process. In the electrolytic refining of gold by the Wohwill method, the electrolyte contains about 100 gpl gold as AuCl, and 100 gpl free hydrochloric acid. Any palladium and platinum contained in impure gold dissolve and accumulate in the electrolyte. When their concentration approaches that of gold, it becomes desirable to discard the electrolyte and to recover the gold and the palladium and platinum. As practiced at Canadian Copper Refiners until recently, discarded electrolyte was treated with sulfur dioxide to precipitate the gold. 2AuCl3 + 6H2O + 3SO2 —2Au + 6HC1 + 3H2SO4 The gold precipitate was filtered off, washed with water, and melted with scrap anodes. The wash water was added to the gold-free filtrate and treated with zinc dust to cement the palladium and platinum. PdCl2 + Zn — Pd + ZnCl2 PtCl4 + 2Zn—Pt + 2ZnCl2 The precipitate was separated and sold as Pd-Pt concentrate, and the barren filtrate and wash water were discarded. The receipts of palladium and platinum at this company were too small to warrant their refining. The process suffered from a number of disadvantages. Handling the gold-free solution was disagreeable, as it was laden with sulfur dioxide even after blowing with air overnight. Subsequent treatment with zinc dust was also troublesome. A large excess of zinc dust was required. Spray, acid mist, and vigorous evolution of hydrogen accompanied the reaction. The Pd-Pt precipitate was grossly contaminated with occluded unreacted zinc and with yellow granules of sulfur, thought to be formed by the reduction of sulfur dioxide and its derivatives. Repeated boiling of the precipitate with hydrochloric acid and washing with water decreased somewhat, but did not eliminate, the zinc. After drying overnight, the precipitate hardened to a clinkerlike mass that was difficult to grind. Grinding, handling, and packing created heavy dusting. Even weighing in an analytical balance generated dust, indicating that the powder was easily charged with static electricity. The total palladium and platinum content of the powder varied from 56 to 72 pct, with an average of 65 pct. The powder dissolved in aqua regia with difficulty, leaving a small amount of insoluble residue. However, the main drawback of the process was the strongly hygroscopic Pd-Pt product. The powder showed a marked though erratic increase in weight and a corresponding decrease in assay on exposure to air, even during the course of laboratory analysis. Such changes were the source of disagreement between Canadian Copper Refiners and the buyers of concentrate. The cause of the change in weight is believed to be hydrogen, liberated by the action of zinc dust on hydrochloric acid. Some of this hydrogen was adsorbed so strongly by the precipitate that it could not be driven off during the drying. On exposure to air it oxidized catalytically, forming water. Experiments soon showed that the entire process of treatment of discarded electrolyte then in use would have to be changed. A small quantity of apparatus was moved into the gold room, and experimentation was held to a minimum compatible with the development of a new process. PALLADIUM AND PLATINUM PRECIPITATION It was thought that zinc could be replaced with a reagent other than a hydrogen-evolving metal. Semiquantitative experiments showed that platinum and palladium could be precipitated completely from the gold-free solutions with such well-known reagents as sodium formate, formic acid, formaldehyde, and paraformaldehyde. Sodium formate was the preferred reagent, since the other three are volatile and somewhat toxic. The gold-free solutions used were those saturated with sulfur dioxide, partly freed of sulfur dioxide by aerating overnight, completely freed by boiling, as well as strongly and weakly acidic, neutral, and alkaline solutions. The reactions are complex and can be represented by these over-all equations: PdC1, + HCOONa — Pd + NaCl + HC1 + Co2 PtCl4 + 2HCOONa — Pt + 2NaCl + 2HC1 + 2CCX, Strongly acidic solutions required as much as five times the theoretical amount of sodium formate as did solutions neutralized to pH 4.5. Increasing the pH decreased the consumption of

Jan 1, 1965

By B. L. Averba

THE determination of retained austenite by X-ray diffraction uses the following relationship:"" Pa = constant . RVaA (8) [1] where: P is the diffracted power from phase a; R, the calculated intensity factor; A, the absorption correction; 8, the diffraction angle; and Va, the irradiated volume of phase a For a flat sample making a glancing angle + with the incident beam the absorption correction is calculated as: * 1 sin (28 - 4) A .= 1 [2] µ sin, (28 — 4) + sin 4 where µ is the linear absorption coefficient. Beu3 has proposed that the computed absorption correction be combined with the constant and that the experimental observation of the absorption correction used in the original method be eliminated. This procedure is permissible only if: 1—There is no preferred orientation in the sample, and 2—The geometric requirements have been met precisely. If these conditions are not met the validity of the determination is questionable. Unfortunately the necessary conditions must be tested experimentally for each determination, and this is done most easily by observing whether the apparent absorption has the form of Eq. 2. In practice it may be convenient to plot P/R vs the parameter sin (2? — )[sin (28 — +) + sin +] to obtain straight lines for the ap- parent absorption correction. Deviations from straight lines indicate either that the sample has not been positioned correctly or that the relative intensities are incorrect. Geiger counter spectrometer methods also have been used successfully for retained austenite determinations. In the usual spectrometer arrangement the sample makes equal angles with the incident and diffracted beams (8 = ); thus the absorption correction is simply 1/2µ and independent of 8. The retained austenite is then easily calculated from integrated intensity measurements on austenite and martensite lines. If the austenite content is not too low and if excessive fluorescence is not encountered it is possible to use filtered radiation and a recording spectrometer. The integrated intensities are then proportional to the areas of the diffraction peaks. For lower austenite contents the following technique was used: A bent quartz monochromator and a Geiger counter spectrometer are employed. The monochromatic radiation is focused on the front slit, and the counter slit is made broad enough to include the entire line. A series of readings are taken in the vicinity of the diffraction peak. The highest reading includes the diffraction line plus background. The background is obtained from the average of several readings on each side of the peak. The integrated intensity is obtained by subtraction. CrK, and FeKa have been used for such determinations. This technique has been found to be as sensitive and as accurate as the photographic methods. In the spectrometer methods the ratio austenite/ martensite may be obtained from readings on austenite and martensite lines and the application of Eq. 1. It is also possible to use external standards and to obtain the austenite contents from measurements on the austenite lines alone. The small correction for carbides then becomes unnecessary. The best standards are probably samples with known

Jan 1, 1954

By R. J. Stoehr, F. Howell

Since the ore mined in the Grants-Ambrosia Lake uranium area is taken from a water-saturated sandstone formation, part of the milling operation includes a drying process. The authors discuss the merits and disadvantages of two methods: natural drying and mechanical gas-fired drying; operating and cost data are included. In the Grants-Ambrosia Lake uranium area, approximately 7000 tons of ore are mined each day from a water-saturated sandstone formation. This ore is sampled and treated at four separate milling operations. Prior to the design and initial construction of the milling facilities, very little was known as to the physical properties of the ore which would be handled in the sampling and crushing facilities at the mills. All four mills initially were constructed without ore-drying facilities. As mining proceeded, it was determined that, even after drying the ore in place by use of drainage development underground, the moisture content of the ore as hoisted averaged approximately 18 pct. Actually, some of the mines produced ores which resembled cream-of-wheat in character and had a moisture content in excess of 24 pct. Each of the four mills had a differently designed sampling and crushing plant; therefore, the moisture content of the ores had varying adverse effects upon the operation of the plants. It was determined after some experience that most of the sampling and crushing facilities could not economically handle ore if the moisture content was greater than 10 pct—one operator considers 12 pct moisture as a maximum. In all of the plants, moisture content over 8 pct increases costs to some extent. In addition to the added sampling and crushing costs, some of the mills were located 15 to 20 miles from the mines and the high moisture content of the ores increased the haulage costs from the mine to the mill. It was generally conceded that it was necessary to employ some method to reduce the moisture content of the ore prior to sampling. Several methods were considered: 1) natural drying at the mine site, 2) mechanical gas-fired drying at the mill site, 3) mechanical gas-fired drying at the mine site, 4) radiant heating on concrete clabs, and 5) infrared shed drying. After preliminary investigation all possibilities but natural drying and mechanical gas-fired drying at the mill site were eliminated. NATURAL DRYING A cooperative feasibility study was conducted on the natural drying method. This study indicated the following: 1) During summer months May through September, ore piled 4-ft deep would dry from +20 to +10 pct HzO in 30 days with no mechanical turning. 2) In the first four days after piling a reduction of 5 to 7 pct total moisture content was accomplished by drainage and absorption of the water into the underlying ground on which the ore was piled, providing the ground surface absorption rates approached 10 gal per sq ft per day. After the first four days the decrease of moisture caused by drainage was practically nonexistent. 3) In the summer months drying by evaporation amounted to approximately 0.1 pct decrease in total moisture per day and mechanical turning of the ore could increase this as much as three times. 4) Climatic conditions of the area indicated that: a) Air temperatures averaged 64' May, June, July, August, September; 41" October, November, December, March, April; 31" January, February. b) Average rain fall was 10 in. with 40 pct of this occurring during July and August. c) Only on very rare occasions were there over five consecutive days with below freezing temperatures. d) The annual evaporation rate was approximately 75 in. On the basis of this study, two of the mill operations decided to attempt to meet the moisture specifications by natural drying supplemented by mechanical turning. The other two operations decided upon rotary gas-fired drying at the mill site. The natural drying method has been quite successful in practice. The ore running approximately 18 pct moisture is trucked from the head frame and piled in rows about 6 ft wide, 3 1/2 ft deep, 5 feet apart during the months of May through September. In approximately 30 days this ore will

Jan 1, 1961

By Lyon F. Terry

IN contemplating the prospects of natural gas being transported from the fields where it is produced to such distant points as Philadelphia, New Jersey, New York City, and New England, let us review the advance that natural gas has made and the projects currently scheduled for construction. This may give us a perspective of the point in the long-range development of the natural gas business in which we now find ourselves, and some basis for judging the further expansion of the industry. Authentic statistics of the total marketed production of natural gas in the United States have been compiled by the Bureau of Mines since the year 1906. The growth of the business is indicated by the following data on marketed production for each ten-year interval since 1906:

Jan 1, 1947

By O. D. Sherby, J. E. Dorn

For elevated temperature-constant load creep tests of a solid solution alloys, the creep strain is a function of a temperature-compensated time parameter 0 = je H/RT dt. The activation energy H is equal to o constant of about 36,000 cal per mol. The substructures resulting from a given creep stress condition are functions of the creep strain independent of temperature. Each new creep stress gives a new unique set of grain substructures; this is one of the factors responsible for the failure of the mechanical equation of state for creep. IN this report an attempt is made to correlate the creep properties of dilute a: solid solutions in aluminum with the subgrain structures that are developed during creep. The possibilities of such correlations have already been suggested by Wood et al. and others1-" who demonstrated that the subgrain structures are functions of the creep stress, creep strain, rate of creep, and temperature. Investigations by Sherby and Dorn' have shown that the creep strain, E, at constant load for dilute a solid solutions of aluminum is given by the functional relationship: e = f(8,u,) [1] where: 0 equals te-AH/RT = temperature-compensated time; t, time; AH, activation energy, - 35,800 cal per mol; R, gas constant; T, absolute temperature, above 400°K; and u,, initial creep stress. Consequently, it was anticipated that the subgrain structure that develops during a constant load creep test should also correlate with any two of the three significant variables C, 8, and Another possible correlation between the subgrain structure and the creep variables is obtained by differentiating Eq. 1 with respect to time, whence the creep rate, 2, becomes: = (2L) (2) =f (, u,) e-AHRT [2] or: e = F (c e H/RT, 0) [3] For the minimum creep rate, ;,, 8 is solely a function of U, as revealed by Eq. 1. Consequently, at the minimum creep rate Eq. 3 reduces to: = F (eAH/RT) [41 Correlations between U, and i, eAH/RT were found valid for solid solution alloys of aluminum where AH was a constant of about 35,800 cal per mol. The parameter ;, eH/RT is identical to the Zener-Hollo-mon parameter8," used by them in evaluating the tensile properties of copper and other metals. Eq. 4 suggests that the subgrain structure developed during secondary creep might be correlatable with either of the two variables 2, e H/RT or u,. Some of the solid solution aluminum alloys which were discussed in an earlier report' were also used in the present investigation. Sheets of these alloys were homogenized, cold rolled from 0.100 to 0.070 in. in thickness and then recrystallized to about the same grain size. Their chemical composition and grain size are recorded in Table I. Creep specimens were selected with their tensile axes in the rolling direction. The details for creep testing have been described10 and will not be repeated here. All creep tests were performed under constant load conditions. Experimental Results and Discussion Metallographic Structure of Creep Specimens: In order to obtain a preliminary concept of creep on the metallographic structure of high purity aluminum, the various ruptured specimens previously used to obtain the creep data for pure aluminum were polished and etched electrolytically in a dilute solution of fluoroboric acid. Oblique illumination was used to reveal the substructures which, for convenience, are shown in correlation with the vs. ;, eH/RT curve in Fig. 1. It is necessary to emphasize that the data for the curve refer to the various secondary stages of creep whereas the micrographs refer to the fractured creep specimens. Nevertheless a regular and systematic correlation is observed between E, eAH/RT (or the creep stress) and the micro-structure at fracture. For In (e, eAH/RT) = 42.3, which refers to creep at a high creep rate and a low creep temperature, the fractured aluminum specimen, as shown by the micrograph in the upper right-hand corner of Fig. 1, exhibited extensive deforma-

Jan 1, 1954

By F. L. Misaqi

The total amount of radon-222 released into the atmosphere by the US uranium mines and mills is only an infinitely small fraction of the total amount of radon released by the top layers of soil with a high concentration of uranium, such as is found in Grants, N. M. Even when compared to areas where mineable deposits of uranium are unknown, the amount of radon released by all US mining and milling operations is still relatively insignificant. Of course, higher local concentrations of airborne radioactivity may be observed around stockpiled ore and

Jan 8, 1976

By N. J. Grant, D. Carne, J. B. Seabrook

IT is unnecessary to review much of the literature on hydrogen embrittlement of steel since several excellent reviews and bibliographies exist.1-3 Hot acid pickling and cathodic charging have been known to cause hydrogen embrittlement of steel and have been used as laboratory methods to charge steels with hydrogen.4-8 Experimental Procedure The problem of prime concern in all instances, except in the work of Sims and coworkers,10 is that at no time was there a definite known hydrogen value reported which could be related to a particular value of the degree of embrittlement. It was the purpose of this research to determine the relationship between hydrogen content and degree of em-brittlement quantitatively. The 1020 stock used for the specimens was hot-rolled 7/16 in. diam rod of the following analysis: 0.19 pct C, 0.40 pct Mn, 0.012 pct P, 0.036 pct S' Vacuum-fusion analyses for nitrogen and oxygen gave 0.014 pct O2 and 0.0011 pct N2. Cathodic charging was used to cause embrittle-ment. The advantages of this method were that no quenching was necessary, the impregnation was reasonably controllable, and representative samples for analysis could be prepared simultaneously with the charging of the tensile bars. Analyses for hydrogen were made in a vacuum-fusion type of apparatus which extracted gas from the samples by fusion in a molten tin-iron bath' This apparatus, which has recently been described in detail elsewhere, will not be discussed here.". " Consecutive samples can be analyzed every 15 min with an accuracy of 0'03 ppm. A A from an electrolytic or pickling bath can be charged for analysis in about 3 min, and analysis completed in 15 min. Samples of as-received 1020 stock were analyzed and found to contain a negligible amount of hydrogen (0.06 ppm). Preliminary pickling and electrolytic charging gave highly variable results. Cold-worked samples showed higher values but ranged from 0.6 to 6.0 ppm of hydrogen. Charging at 90°C gave higher values of charged hydrogen, but troublesome films on many of the specimens resulted. It was not until a few drops of a catalytic poison, prepared from 2 g of yellow phosphorus dissolved in 40 ml of carbon disulphide,8 was added to the electrolytic cell that fairly consistent high values of hydrogen could be charged into the as-received 1020 steel at room temperature. The cell used is sketched in fig. 1. The anode and fixture for the tensile specimens were fastened to the cell cover as shown, and the specimen was screwed in place, centrally located with respect to the anode. At first, anodes of lead and graphite were tried, but they contaminated the electrolyte and gave a slight deposit on the specimen. Later, a platinum wire was used in the form of a uniform helix. A current of 2 amp, corresponding to about 0.5 amp per sq in. of cathode, was used for most specimens. The electrolyte was 4 pct H2SO4 solution. Fig. 1 shows the form of the special tensile bar, the main portion of which was an ordinary 1/4 in. diam, 1 in. gauge length test bar, except that two to four small cylinders of stock were left attached by small links to the bottom end of the tensile bar for the purpose of providing samples for hydrogen analysis. Thus the bars and samples were charged with hydrogen simultaneously and an analysis could be made while the bar was being tested mechanically. Experiments were performed to determine how representative the test cylinders were of the middle of the test bar proper. While the bar center was being analyzed, the small cylinder was stored in dry ice, since it had been shown that such storage prevents loss of hydrogen for many hours.12 The results of these checks are shown in table 1. The checks are very good (0.3 ppm) and indicate that it is permissible to use the small end cylinders to establish the hydrogen content of the tensile test bar proper-

Jan 1, 1951

By Arnulf Muan, R. W. Taylor

Activities of iron in Fe-Pt alloys have been dctermined by equilibrating mixtures of platinum metal and iron oxide at known oxygen Pressures in a thermobalance at 1300°C. Conzpositions and iron activities of the oxide phase at equilibrium are known from previous work, and compositions of the Fe-Pt alloy phase formed at equilibrium were detcvt?zined from the observed weight changes of the samples. The activity curve obtained shows a strow negative deviation from Raoult's law. THE present investigation was undertaken as part of a research program dealing with phase equilibrium relations existing among the oxides of iron and titanium at 1300°C. At low oxygen pressures of the gas phase in equilibrium with these oxides, the iron activity of the system is high, and considerable alloying of iron with the platinum used as a container material takes place. Thermodynamic data for Fe-Pt alloys at 1300°C are needed in order to evaluate quantitatively the extent of such reactions. Larson and chipmanlhave determined activities of iron in Fe-Pt alloys at 1550°C by equilibrating platinum metal with CaO-iron oxide-SiOzmelts in which the iron activities were known. Compositions of the resulting Fe-Pt alloys were determined by chemical analysis. Mundiath and Gerassimov2 have studied thermodynamic properties of Fe-Pt alloys by electromotive force measurements in the temperature range 550" to 1000°C. The experimental method used in the present investigation is a slight modification of that used by Grube and Ratsch3 in studies of NiCr-alloys. 1) EXPERIMENTAL METHOD 1) General. Mixtures of platinum metal and iron oxide were equilibrated at 1300°C in atmospheres of known oxygzn przssures, and the course of the reactions was followed by measuring the weight changes of the mixtures. The principles involved in the derivation of composition-activity relations from these measurements are illustrated by the composition triangle for the system Fe-FeZO3-Pt shown in Fig. 1. Take as an example a mixture of FeZO3 (hematite) and platinum such that the total composition is represented by point T. If this mixture is heated to 1300c in air (poz = 0.21 atm) and the oxygen pressure is then reduced gradually, the oxygen content of the oxide phase decreases and increasing amounts of iron enter the metal phase. As the oxide phase and the metal phase for all practical purposes are insoluble in each other, their compositions are represented by points moving toward Fe along the joins Fe-Fe,03 and Fe-Pt, respectively. The total composition of the mixture during this process also changes, but only with respect to oxygen content, because the vapor pressures of iron and platinum are negligible at 1300°C. Hence the change in total composition is described by a straight line (constant Fe/Pt ratio) radiating from the 0 apex of the composition triangle Fe-Pt-0, of which the triangle in Fig. 1 is a part. Only one such line ("oxygen reaction line", T-T",) is shown in Fig. 1. The total composition of the alloy-iron oxide mixture at any instant must, in addition, be located on the straight line (conjugation line) connecting the two points representing the compositions of the two coexisting phases. It therefore follows that the total composition of the mixture at any instant is represented by the point of intersection between the conjugation line and the oxygen reaction line. An example of the situation prevailing at a chosen oxygen pressure, po2, is shown in Fig. 1 by points a' (alloy composition), b' (oxide composition) and T' (total composition). Point b' is known from the work of Darken and Gurry,4 and point T' is experimentally determined by the observed weight change of the mixture (distance T-T). Hence, point a', the composition of the alloy, is determined from the above data as the intersection between the join Pt-Fe and the extension of the straight line bl-7'. The activity of iron in the alloy at equilibrium is identical to that of the iron oxide phase, if the same

Jan 1, 1962

I-institute of Metals Division S. SKOWRONSKI, Chairman ZAY JEFFRIES, Vice-chairman WILLIAM M CORSE, Secretary Executive Committee J. R. FREEMAN, JR, Local Section G E JOHNSON R S ARCHER, Non-ferrous Data Sheets P. D. MERICA EDGAR C BAIN, Journal Committee L W SPRING SAM TOUR, Papers Committee F. L. WOLI H. C. JENNISON, Membership Committee Local Section Committee J. R. FREEMAN, JR., Chairman R. J. ANDERSON, Cincinnati R L. DOWDELL. Minneapolis R. S WILLIAMS, BostoI G. H. CLAMER, Philadelphia W. A SCHEUCH, Chicago R. F. WOOD, New York

Jan 1, 1923

ENGINEERS AVAILABLE, (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members) Member, aged 33, technical graduate, B. S. and E. M., soon to complete contract in Spanish America, desires to get in touch with employers. Ten years mine, mill, cyanide and construction experience. Prefers executive position or assistant to executive. No. 352. Member; University graduate, desires responsible position with good company. Married.' Age; 37. Fourteen years' experience in Australia, Mexico and United States, milling, cyaniding and concentrating, gravity

Jan 5, 1917

By D. Muraoka

Introduction Soda ash, anhydrous sodium carbonate, is produced from underground trona deposits occurring in the Green River Basin of southwestern Wyoming. Stauffer Chemical Co. of Wyoming, a jointly owned subsidiary of Stauffer Chemical Co. and Rocky Mountain Energy Co., mines the trona and processes it into high-purity soda ash. Stauffer Wyoming has been in operation since 1962 with a current production capacity of about 1.8 Mt (2 million st) per year of soda ash. The refinery has five parallel operating trains using the monohydrate process which is a series of chemical processing unit operations described below. Screening and Crushing The mined trona is brought to the surface in two counterbalancing ore skips. The ore is initially screened with refinery feed (less than peagravel size material) entering the process. Oversize is conveyed to an outdoor stockpile. Ore is recycled from under the stockpile via cone feeders as the refinery needs require. The ore is conveyed to hammer type crushers and screened. The refinery feed enters the process and the oversize is recycled to the crushers. Calcining The first step in refining trona to soda ash is calcining the trona ore. This is accomplished in concurrent flow, rotary kilns that are direct fired with natural gas. [2 (Na CO NaHCO 2H O) Heat 3Na CO + 5H20 + CO 2 3~3~ 2 ~~2 32] The trona ore is fed to the kiln at the burner end and is intimately mixed with the hot exhaust gases from the burner. Direct contact with the flame is avoided. The ore moves down the kiln by gravity and rotation aided by the kiln's internal lifters. The exhaust gases are cleaned to 99 + % particulate removal and discharged to the atmosphere. Dissolving the Calcined Trona The calcined trona is conveyed from the kiln discharge to a rotary drum dissolver where it is mixed with water and weak solution (unsaturated solution of calcined trona in water). The calcined trona is soluble whereas the impurities, primarily shale, are insoluble. The discharge from the dissolver is a slurry containing saturated solution (about 30% dissolved calcined trona in water), some undissolved calcined trona, insoluble impurities, and organic impurities. The dissolver discharge enters a rake classifier that makes the first solid/liquid separation in the process by removing the heavy undissolved material from the saturated solution. This undissolved material is conveyed to a second rotary drum dissolver and mixed with water to dissolve any remaining calcined trona. The secondary dissolver discharges to a second rake classifier that separates the solids from the liquid. The solids are now primarily insoluble impurities with very little unrecovered calcined trona. These wastes are conveyed to evaporation ponds for disposal. The liquid from the secondary rake is recycled to the primary dissolvers' weak solution system. Returning to the primary rake classifier, the saturated solution which contains suspended insoluble muds is pumped to a thickener. Flocculant is added to aid settling of the suspended muds. The flocculated muds are collected at the bottom of the thickener and pumped to vacuum cloth filters. The adhering saturated solution is separated from the muds that remain on the filter cloth. The recovered solution is returned to the dissolvers' weak solution system. The muds are reslurried and pumped to the evaporation ponds for disposal. Saturated solution, containing some suspended insoluble muds along with the organic impurities, overflows the thickener. Filtering the Saturated Solution The saturated solution overflowing the thickener enters a holding tank where it is pumped to a bank of pressure leaf filters. The suspended muds are captured on the filter leaves while the cleaned saturated solution is pumped to polishing filters. The polishing filters are also leaf pressure type, intended to remove any suspended solids that may pass the primary filters. Organic impurities are removed with activated carbon. The purified solution is now free of insoluble muds and has most of the organic impurities removed. Crystallizing and Drying the Monohydrate The purified saturated solution is pumped to evaporative crystallizers. The solution is circulated from the crystallizer vessel through a heat exchanger. Indirect contact with steam in the heat exchanger causes the saturated solution to boil, thus crystallizing the soda ash in its monohydrate form. Slurry crystal density is maintained in the crystallizer by simulta¬neous feed of fresh saturated solution and drawoff of the slurry.

Jan 1, 1986

[Arizona BRENT N. RICHARD, Chairman ROBERT W. HUGHES, Vice-Chairman ROBERT E. S. HEINEMAN, Secretary-Treasurer Arizona Bureau of Mines, University of Arizona, Tucson, Ariz. THOMAS G. CHAPMAN A. MENDELSOHN WILLIAM KOERNER A. C. REIFSNIDRR C. R_ . KUZELL WILLIAM M. SABEN ERNEST WITTENAU Black Hills NATHANIEL HERZ, Chairman C. E. DAWSON, First Vice-Chairman BANCROFT GORE, Second Vice-Chairman C. E. SCHMIDT, Secretary-Treasurer Homestake Mining Co., Lead, S. D. R. S. BLITZ NATHANIEL HERZ C. E. DAWSON A. I. JOHNSON L. B. EAMES F. C. LINCOLN BANCROFT GORE C. E. SCHMIDT]

Jan 1, 1940

By J. Boldy

Discovery of the Delbridge massive sulfide deposit in the Noranda district of Quebec resulted from an appreciation of the significance of a mercury leakage halo as a lithochemical pathfinder to blind ore. Its location, relative to a geologically inferred ore-bearing horizon within complex volcanic stratigraphy was also a factor. Systematic sampling of microfractures present in outcrops delineated a diagnostic anomaly, drawing attention to an area considered prospective for buried ore. The massive sulfide deposit was subsequently found to be blind and topped at the 110-m (360-ft) level.

Jan 1, 1985

By Robert E. Wilson

TO show the vital importance of our future oil supplies to our economy, I will merely point out that this country, with something like 15 per cent of the world's land area and something like 7 per cent of the world's population normally uses between 65 and 70 per cent of the motor vehicles of the world, between 65 and 70 per cent of the world's rubber, and produces and refines between 65 and 70 per cent of the world's petroleum. Despite all the arguments as to which is cause and which is effect, all will agree that all three of these important industries are mutually dependent. If we had not been able to produce 65 or 70 per cent of the world's oil in this country we would not have the degree of mechanization, or the efficiency of transportation, or the high industrialization that we enjoy. Furthermore, the fact that oil has been plentiful and cheap has had a tremendous effect on all the things in which we as engineers are interested. For that reason, if for no other, it is well to look ahead to see what the outlook is for the near and far-distant future.

Jan 1, 1945

NEW YORK SECTION J. E. Johnson, Jr., Chairman Edgar Rickard, Vice Chairman. D. M. Liddell, Secretary, 7 Wall St., New York, N.Y. C. A. Bohn, Treasurer John V. N. Dorr Lewis W. Francis. The annual meeting of the New York Section was held on Wednesday, June 6, with about 40 members in attendance. The treasurer re a brief summary of-the financial statement for the year, and the secretary's report was read. These reports were ordered placed on file together with the report of the auditors for the two previous years.

Jan 8, 1917