Search Documents

By J. A. Gay

BRITISH success in extracting significant quantities of germanium from gas works flue dusts has been one of the prime forces in promoting similar research in the United States. Pittsburgh Consolidation Coal Co. and Pennsylvania Coal & Coke Co. are two of the larger U. S. firms with germanium from flue dust research programs. British interest in germanium started in 1933 when V. M. Goldschmidt reported that some coals from the Yard Seam of Northumberland and Durham contained 30 to 50 ppm of germanium.

Jan 8, 1953

By Thomas O. Ziebold, Robert E. Ogilvie

Experimental analysis of diffusion samples covering the entire Cu-Ag-Au system at 725°C has been carried out. Experimental coefficients are computed at twenty-eight points in the lermary system. It is found that the direct coefficienl for copper is nearly independent of the silver, content for 1ow-silver alloys and that the cross coefficient for silver correlates with the ther-nzodynatnic properlies. This lalter observalion leads to the conclusion that the mobililies of copper and gold are nearly equal. Thermodynarmic actiuilies for Cu-Ag-Au were computed from binary data and adjusted to be consistent with neasured tie lines across the two-phase region which extends into the ternary diagram at 725°C. Application of these therknodynarnic calculaliorls to the dijftcsion data terifies the Onsager reciprocal relations to the extent that experimental uncertainlies will allow. It is jound that diffusion neav the critical point of the 1200-phase field in the isothermal section at 725°C causes the composition gradients for copper and silver to approach infinity while the direct and cross coeficients become equal. From the standpoint of experimental Procedures, it has been shown that microanalysis of ternary samples may be carried out using a simple expression for the conversion of X-ray zntensily to composilion. The accuracy of' this method has been demonstrated by the analysis of standard alloys and by the reproducibility of composition determinations using differed X-ray lines. DIFFUSION in a ternary alloy system is basically and significantly different from diffusion in binary alloys. When only two elements are present there is just one independent composition variable, and the diffusion profile of composition vs distance across a sample must change monotonically through all solid solutions bracketed by the terminal alloys. If two-phase regions are stable for compositions between the terminal values, these must appear as planar interfaces in the diffused sample, with the composition profile exhibiting sharp discontinuities. Adding a third element may alter this picture completely. Because of the additional degree of freedom in the composition, we may see composition profiles which do not change monotonically through solid-solution ranges, and stable, nonplanar phase interfaces. Even though two-phase regions may lie between the terminal compositions of a diffusion sample on the constitution diagram, they will not necessarily appear in the diffusion profiles. In binary diffusion only one coefficient is needed to describe the interdiffusion process. From Fick's law this coefficient relates the diffusive flux of one component to its own composition gradient. In ternary diffusion we must allow for cross interaction between the two independent species. By a linear extension of Fick's law we introduce "cross" or "off-diagonal" diffusion coefficients which relate the flux of one component to the composition gradient of the other independent constituent. Thus, we require four interdiffusion coefficients to describe the transport process in a ternary system. In its most general form,1,2 the rate equation for mass transport by isothermal diffusion in a system of s components states that the diffusive flux of component i, Ji, is a linear summation of all driving forces, Xk, each force being multiplied by an appropriate compliance coefficient:

Jan 1, 1968

By C. H. Samans, G. F. Tisinai, J. K. Stanley

The times at which the first detectable amount of a phase forms at temperatures between 900° and 1800°F were determined. Both X-ray diffraction and metallography were used to detect a in highly strained filings; metallography alone to detect it in annealed bulk samples of six different types of stainless steels. The a phase was found to form in accordance with the C-type reaction curve in both austenitic and ferritic alloys. In filings of types 304, 347, and 446, a formed in a few hours, and in types 316, 309, and 310, it formed in a matter of minutes at temperatures corresponding to the knee of the C-curve. Only in the bulk type 309 steel, after 500 hr, and in the bulk type 310 steel, after as short a time as 25 hr at temperature, was n detected; in both instances at approximately the same optimum temperature as in the filings. The annealing temperature affected a phase nucleation only for the filings of type 304 and 347 steels, and for the bulk samples of type 309 and 310 steels. KNOWLEDGE of both the rate of nucleation and the rate of growth of the new phase is required for a complete description of metallurgical rate phenomena. However, data on the time for nucleation alone may frequently be useful in evaluating the tendency of commercial stainlcss steels to form s under various conditions. Very little correlated information of this type is available in the literature. Shortsleeve and Nicholson' indicate that s forms in ferritic 24, 27 and 30 pet Cr steels according to a C-type of reaction curve, and Emmanuel's' data for austenitic type 310 steel also suggest this type of solid state reaction. In addition, significant, though fragmentary, information has been given by Binder, Dulis and Smith,4 Payson and Savage,.; Guarneri, Miller, and Vawter,8 rerichs and Clark,7 Wilder,5 Lismer, Pryce, and Andrews,' Smith, Dulis, and Link,10 Dulis, Smith, and Houston," and Henry, Cordovi, and Fischer." The bearing of these data on this work is covered in the discussion. The purpose of this paper is to present such correlated data on s formation in AISI type 304 (18 pct Cr-8 pet Ni), 347 (18 pet Cr-10 pet Ni-Cb), 316 (18 pet Cr-12 pet Ni-2 pet Mo), 309 (25 pet Cr-12 pet Ni), 310 (25 pet Cr-20 pet Ni), and 446 (27 pet Cr) stainless steels. Materials and Test Methods X-ray diffraction and metallographic methods were used to determine the first appearance of the s phase in cold worked filings and in annealed bulk samples of seven steels, under various combinations of time and temperature. The rate of growth of the s particles was not determined. Commercial heats of six AISI steels and a low carbon laboratory experimental heat containing about 28 pet Cr were studied. Analyses are given in Table I. Because cold work greatly accelerates the nucleation of s particles, the relative rates of s nucleation in mechanically strained samples, i.e., filings through 120 mesh, were determined for direct comparison with those in annealed bulk alloys of the same composition.

Jan 1, 1957

By C. A. Bruch, J. F. Duffey

On the basis of metallographic and cooling-rate studies of 15 U-Zr alloys, a new version of the 6 phase region of the U-Zr phase diagram is proposed. IN several published diagrams of U-Zr alloy system:' there is good agreement that at elevated temperatures complete solid solubility exists between y uranium and ß zirconium. Similarly, there is reasonably good agreement concerning the uranium-rich and zirconium-rich ends of the diagram. However, there is no agreement concerning the nature of the diagram at intermediate compositions and at temperatures below about 650°C. The early work of Saller et al.8 hows an intermediate phase, 6. In a later diagram by Saller and Rough' shown in Fig. 1, the d phase field is drawn with dotted lines, indicating doubt that this phase exists. The diagram of Summers-Smith2 does not show the d phase. More recently Holden and Seymour' have shown that in the composition range 40 to 60 wt pet Zr, the high-temperature ? phase, which is body-cen-tered-cubic, transforms to an ordered structure, 8. They found that the order-disorder transformation occurs between 595° and 610°C, and presented a diagram based on the study of four different alloy compositions. Most recently Saller et a1.5 presented a new diagram which differs with respect to the composition limits of the 8 field from the others proposed by these authors. The purpose of the present investigation was to determine the boundaries of the d phase field. Experimental Procedures and Results Alloys—Buttons, weighing 80 g of 15 different alloy compositions were prepared by arc melting Mal-linckrodt uranium and iodide-process zirconium in a water-cooled crucible. A controlled atmosphere of argon and helium was maintained in the furnace. Prior to making each button, a sacrificial button of zirconium was melted to increase the purity of the furnace atmosphere. Each alloy was then melted six times to improve its homogeneity. Subsequently the alloy buttons were jacketed in copper and hot rolled to slabs at 775°C. From these slabs, specimens were machined for chemical, thermal, and metallographic analyses, Table I gives both the estimated chemical composition of the alloys, and the values which were obtained by analysis. The oxygen contents varied from 0.013 to 0.032 pet, nitrogen from 0.0014 to 0.014 pet, and carbon from 0.0013 to 0.011 pet. The purity of the alloys ranged from 99.947 to 99.975 pet. Thermal Analysis—The specimens for thermal analysis were blocks 11/4 x 1/4 x % in. The bead of a calibrated thermocouple was placed between two of these blocks and molybdenum wire was wrapped around the assembly. Each assembly was sealed in a quartz capsule having an argon atmosphere. The capsule was placed inside a refractory crucible which was heated in a furnace. Using a method described by Smith,' the emf of a differential thermocouple, with junctions inside and outside of the refractory crucible, was used to activate the

Jan 1, 1959

By R. E. Carter, F. D. Richardson

Self-diffusion coefficients have been measured for iron in wustite (700° to 1000°C) and for cobalt in cobaltous oxide (800&apos; to 1350°C) by means of radio-isotopes. Both sectioning and decrease of surface-activity methods have been used and a particular shortcoming of the latter method has been disclosed for wustite. The effects of oxygen pressure on the composition of cobaltous oxide and on the diffusion coefficient of cobalt in the oxide have been established. The effect of the preparation conditions of the cobalt-oxide specimens on the diffusion measurements has been determined. It has been concluded that diffusion of cobalt occurs via vacant cation sites and that a cobaltous-oxide disk reaches equilibrium with its environment in a time which is very short compared with that needed for diffusion of the radio-isotope. THE availability of radioactive isotopes in recent years has permitted the measurement of many self-diffusion coefficients which were hitherto impossible to determine. With the advent of radioactivity, the method of measuring diffusion coefficients has also changed. The earlier sectioning method by which the concentration profile of the diffusing species was determined in the diffusion specimen has often been rejected in favor of the decrease of surface-activity method first developed by Von Hevesy,&apos; and extended by Steigman, Shockley, and Nix,&apos; and Raynor, Thomassen, and Rouse." With the experimental arrangement where an infinitely thin deposit of tracer is diffused into a semi-infinite cylinder, the decrease in activity of the active face due to diffusion of the tracer into the specimen is measured by counting the active face before and after diffusion. Under these conditions, the appropriate solution of the diffusion equation is R = e*(l-<K/Z) [1] where R is the ratio of the counting rates after-to-before diffusion, $& is the Gaussian error integral of \/Z, and Z is defined as Z = p2Dt, p being the linear-absorption coefficient of the detected radiation in the diffusion specimen, D the self-diffusion coefficient, and t the diffusion time. In the older sectioning method the concentration distribution of the tracer is found after diffusion by analysing thin parallel sections cut from the active face of the diffusion specimen. As seen from the solution of Fick&apos;s second law for the distribution of an infinitely thin source after diffusion into a semi-infinite cylinder the log of the concentration plotted against x&apos; will be a straight line of slope log e/4 Dt. The diffusion coefficient thus can be calculated directly. The units of the tracer concentration are completely arbitrary, since any change in units does not change the slope of the log c vs x2 lot. Although both of the above methods have been widely used, a thorough experimental comparison does not appear to have been made. Birchenall and Mehl,&apos; during an investigation of the self-diffusion rate of a and r iron by the surface method using Fe" tracer, diffused and sectioned one welded couple. The diffusion coefficient from this run agreed with those by the surface method. Buffington, Bakalar, and Cohen," during an investigation on a and y iron

Jan 1, 1955

By S. R. Mitchell, M. Weissman, J. H. Brown

It has been demonstrated that for fine grinding operations, the energy input (E) and the product size modulus (k) are related by an equation of the form E = Ak1-n (1) where "A " and "n" are constants.(1) Also, it was suggested that "A" is determined by the comminuting device and that "n" depends primarily on the rock. It was the purpose of this investigation to study these constants by determining the form of an energy-size reduction relationship over an extreme range of energy inputs, and at the same time, to evaluate the minimum particle size produced during grinding. The comminution system consisted of a stainless steel laboratory ball mill in which quartz was ground at 60% solids for times ranging from 1 minute to 700 hours. The mill which measured 10" diameter by 12" long was loaded with about 60 pounds of balls ranging in diameter from 3/8" to 1-1/8" and was driven at 55 r.p.m. Quartz was selected for the tests because it is a brittle material for which size distribution data were expected to show a constant distribution coefficient regardless of product size.(1) This permitted specification of product size by a size modulus alone. The quantities measured were the time of grind (measure of energy input) and the specific surfaces of the products. Since no accurate method is available yet for determining particle size directly in the very fine size ranges specific surface data were used for this purpose. The relationship between these two quantities may be expressed as where Cis a constant which includes a shape factor, p is the specific gravity of the solid,_S is the specific surface and D is an equivalent particle diameter. For a material in which the distribution coefficient does not change with size the term (l/S) may be substituted for k in equation L if the proportionality constant "A" is changed correspondingly. This substitution was made in this work but in addition, screen analyses were made on several products to verify the equivalence of the two methods of size specification. EXPERIMENTAL DETAIL QUARTZ Quartz from two sources was tested. One series of tests was made on a clear, high purity crystalline quartz from Brazil and Arkansas, and another series was run on massive quartz fromNewHampshire. Grinding charges of the high purity material consisted of 2000 gram samples of -3-8 mesh particles, while the charges of the New Hampshire quartz were 500 gram samples of a -35+48 mesh screen fraction. The difference in the sizes of these two series of charges was not significant in view of the extreme size reduction accomplished, and the New Hampshire samples were smaller to permit ginding to finer sizes in shorter times than required for 2000 gram lots. SAMPLING AND ANALYSIS Separate charges were ground for all tests in which the grinding times were less than one hour and for all tests on New Hampshire quartz since these products were difficult to sample accurately without affecting the entire charge. During the long time grinding tests the mill was

Jan 1, 1961

What has happened to the basic coal industry during the past year? Has it been a better year for coal than 1961? What striking new developments have occurred in mining, preparation and utilization? Are there positive signs that production will go up? What has happened in the utility market, the metallurgical market and the export market? Is the controversial question of coal transportation nearer to a solution? What progress has research made for coal during the year? The answer to these and many other important questions are offered in the following review of the Coal Industry-1962.

Jan 2, 1963

By LIONEL E. BOOTH

ORE tests are made for the purpose of determining the correct methods of treatment for any particular ore. They should be conducted so as to insure that the results obtained in actual mill practice, on ore of similar grade and physical nature, will duplicate the results obtained in the test work. As the expenditure of many thousand of dollars may be involved in the building of the necessary mill, the testing of ores calls for extreme care and skill in handling laboratory machines, and a knowledge of actual practice to guard against the danger of obtaining results in test work that would be impractical to duplicate on a commercial scale. The importance of a correct sample of the ore is at once apparent. No matter with what degree of care the test 4rk is done, it loses its value when made on an unrepresentative sample. It is the first safeguard against future disappointments in the loss of capital and time. A number of failures in the past have been traced directly to faulty or lax methods in obtaining the ore sample.

Jan 1, 1924

By William H. Spice

Exploratory drilling in South Central Texas for the year 1944 showed a marked increase over that of 1943 and resulted in a similar increase in new fields discovered. In this area, which comprises the 30 counties included in district No. I, Oil and Gas Division, Railroad Commission of Texas,? 61 exploratory wells were drilled during 1944 as compared with 29 exploratory wells drilled during 1943, or an increase of over 100 per cent. Three new oil fields, two new gas fields and one gas-distillate field were discovered during the year, as compared with one new oil field and one new gas field discovered during 1943. These new fields were the result of exploratory drilling throughout the district along the Wilcox trend and the deeper Edwards lime trend, which was started during the previous year. The Wilcox trend yielded the new Loma iilta-Wilcox oil field and the San Caja gas-* tlistillate field, both in McMullen County. The Charlotte field, in Atascosa County, was discovered along the deeper Edwards lime trend. These three discoveries were of considerable importance and subsequent development should indicate the desirability of continued exploration along these trends. The other three discoveries, United oil field in Guadalupe County, Pederson gas field in Milam County and Van Cleve gas field in Zavalla County, were of minor importance. Charlotte Field, Atascosa County, was discovered by the Humble Oil and Refining Company&apos;s No. 3 Pruitt, completcd on Aug. 9, 1944, flowing 176 bbl. per day, 3/16-in. choke, 710 lb. tubing, 475 lb. casing pressures, 37.7º A.P.I. gravity, from the top of the Edwards lime from 6917 to 6923 ft. Two oil wells were completed during the year in this field. This discovery is 14 miles southwest of the same company&apos;s Imogene field, also producing from the Edwards lime but with considerable difference in reservoir characteristics. The discovery of this field is the result of surface geology and subsequent seismograph survey of the area. Loma Alta-Wilcox Field, McMullen County, was discovered by the Atlantic Refining Company&apos;s No. I Atkinson, completed on June I, 1944, flowing 102 bbl. per day, 9/64-in. choke, 1900 lb. tubing pressure, 37º A.P.I. gravity, from Wilcox sand from 6866 to 6869 ft. after being drilled to a total depth of 7185 ft. This discovery is the result of subsurface geology and an extensive seismograph survey of the entire area. Sun Caja Field, McMullen County, was discovered by Edwin M. Jones No. 2-C Ezzell, completed on June 2, 1944 as a dual completion in the Wilcox sands, flowing 1,740,000 cu. ft. gas with 53 bbl. distillate, 1/4-in. choke, 2035 lb. tubing pressure, 53.2º A.P.I. gravity, from sand 6416 to 6453 ft. and flowing 2,000,000 cu. ft. of gas with 127 bbl. distillate, 1/4-in. choke, 2500 lb. tubing pressure, 50º A.P.I. gravity, from sand 6889 to 6916 ft., after being drilled to a total depth of 7264 ft. Three gas-distillate wells were completed during

Jan 1, 1945

By J. M. Lommel

DURING an investigation into the effect of heat-treatment on the creep properties of the magnesium alloy ZW1, (1 pct Zn, 0.6 pct Zr), the previously published methods of final polishing were found to be unsatisfactory. A new diamond-polishing technique has been developed to facilitate the study of fine precipitates in this and other magnesium alloys, and is described in this note. The sectioning and coarse grinding techniques are those of Fox and Hall,&apos; and Hess and Cieorge.&apos; Pre- liminary mechanical polishing is done with 6-µ, and 1-µ( grades of diamond compound on &apos;Microcloth&apos; using a lubricant of &apos;Hyprez&apos; oil. When the conventional technique is used with a 1/4- µ diamond wheel for the final polishing of magnesium alloys, scratching is likely to result from the abrasive action of the &apos;Microcloth&apos; nap on the soft metal surface. This problem has been overcome by the use of a cream on the wheel in order to separate the specimen surface from the polishing cloth. To prepare this cream, a solution of 6-ml tri-ethanolamine in 75-ml water is stirred into 12.5 g stearic acid at a constant temperature of 80o to 90°C. The cream is allowed to cool, and is then &apos;whipped&apos; to a smooth consistency with 100-ml &apos;Hyprez&apos; oil. Before polishing, the diamond loaded &apos;Microcloth&apos; is moistened with a few drops of &apos;Hyprez&apos; oil, then a small amount of cream is worked into the nap. For the best results a wheel speed of 500 rpm should be used for polishing, and the specimen should be held by hand with a light pressure while being rotated in the opposite direction to the wheel. After polishing it is necessary to swab the specimen thoroughly in methylated spirits to remove residual cream and oil from the surface in order to avoid uneven etching and drying stains. Fig. 1 shows the surface finish obtained on a specimen by polishing on a 1/4- µ diamond wheel using the cream, and Figs. 2 and 3 the precipitate observed in ZW1 after polishing, and etching for two seconds in nitric acid 15 pct in ethylene glycol. This new diamond-polishing technique has made a valuable contribution to the programme of metal-lographic research on ZW1 and has become a routine laboratory practice for other low alloy content magnesium alloys.

Jan 1, 1961

By T. A. Rickard

Flaubert, as we know, laid stress on the selection of the right word, le mot juste, the precise epithet, the word that belongs to the thing. A sentence, or even a paragraph, may be spoiled by the use of a word that is not proper, that does not fit or is foreign to the meaning intended. An Australian mining expert is reported to have said: You have a property of considerable value, and what I saw warrants a good development of very rich cubicular galena, with gossan intermixed. &apos;Cubicular&apos; means `belonging to a small bedroom&apos;, a `cubicle&apos; being a sleeping compartment. He meant `cubic&apos;, of course. This is a malapropism, and reminds me of the lady from Chicago that, on her return from Europe, said how much she had enjoyed the rural parts of France, because, among other things, it was "so delightful to hear the French pheasants singing the mayonnaise to the tune of the Los Angelus". It is impossible to amalgamate coal-tar thoroughly with the pulp in the agitating-tank. In metallurgy, `amalgamate&apos; refers to the combination of mercury with one or both of the precious metals, forming an amalgam, which is an alloy of mercury with another metal. It differs from other alloys, such as brass or bronze, in being made without the aid of heat, inasmuch as mercury is molten at the ordinary temperature. The word comes to us from the Greek. through Old French and means `something soft&apos;. It is a mistake to use technical terms, having a specific meaning, for purposes that are foreign to that meaning. The writer of the quotation is not discussing any combination of metals; he is dealing with the physical process of mixing and is using &apos;amal-

Jan 1, 1931

By Frederick H. Williams

The object of this paper is to bring to the attention of those members of the Institute who are interested in the subject, a method for the estimation of manganese, which has been frequently used in the labratory of the Vulcan Steel Works during he last eight months, and which is deemed worthy of more general use. It is simply an adaptation of well-known processes, for the purpose of determining this element in pig iron and steel. In general, the method consists in precipitating the manganese as binoxide dissolving in dilute sulphuric acid in the presence of an excess of a standardized solution of oxalic acid, and titrating the remainder of the oxalic acid left unoxidized with permanganate of potash. For this method, therefore, two standardized solutions are needed, viz., a permanganate solution and an oxalic acid solution. The permanganate solution is made so that 1 C.C. is equivalent to 1 mgr. of iron. By using so weak a solution and keeping tile bulk of the solution to be titrated down to 75 C.C. or a little leas, the accuracy of the process is greatly increased, since the final reaction is almost if not quite as sharp as if a stronger solution were used. The oxalic acid may be of almost any strength, but if made so that 1 c.c. requires 3 O.C. of the permanganate to oxidize it, it will auswer well. The process is then, as follows: from 1 to 2 grams of. pig iron or steel ate dissolved in 40 to 50 C.C. of concentrated nitric acid with the aid of heat. As soon as solution is erected, in the awe of steel, add gradually and cautiously, the solution being kept boiling, sufficient pulverized chlorate of potash to precipitate the manganese as binoxide. Two grams will be a great abundance. In the case of pig iron, first remove the carbon and silica by filtering the solution through asbestos and washing with concentrated nitric acid. Filter the strong acid solution in which the binoxide has been precipitated, through asbestos with the aid of the filter pump. When it has entirely passed through wash well with water. Blow the contents of the funnel into the beaker in which the precipitation was made and rinse the funnel with a little water.

Jan 1, 1882

By Harry Seltz, J. C. DeHaven

InteRmetallic compounds are formed in many binary metal systems. Some compounds are stable to their melting points, and others decompose at lower transition temperatures. Even those of the first class are dissociated in the liquid state, as indicated by the continuous form of their solubility curves at their melting points1. While the lattice structures of some of these compounds have been determined, their thermodynamic properties have not been investigated. In this paper is described the determination of the free energy and heat of formation of the compound CdSb, which is of the first class mentioned above, melting congruently at 455&apos; C. This compound shows a rhombic structure, and the lengths of the edges of the elementary cell containing four molecules are: a = 6.52, b = 8.60, c = 4.16 A.&apos; There are three possible methods of determining the free energy of formation of a compound of this type. The first method, applying the third law of thermodynamics, requires the measurement of its heat capacity preferably to liquid hydrogen temperatures, and a calorimetric determination of its heat of formation. The second method involves the study of the equilibrium of the compound in some gas reaction, such as: CdSb + CO² = CdO + CO + Sb From the known free energies of formation of CdO, CO² and CO the free energy of formation of CdSb could be calculated. The third method measures the electromotive force of a galvanic cell in which the cell reaction is the reversible formation of the compound from the elements. The first method is generally applicable, but requires elaborate experimental equipment. The second method can not be used for compounds melting at low temperatures, owing to the difficulty in establishing equilibrium. The electromotive force method, therefore, seemed to offer

Jan 1, 1935

By J. C. DeHaven, Harry Seltz

InteRmetallic compounds are formed in many binary metal systems. Some compounds are stable to their melting points, and others decompose at lower transition temperatures. Even those of the first class are dissociated in the liquid state, as indicated by the continuous form of their solubility curves at their melting points1. While the lattice structures of some of these compounds have been determined, their thermodynamic properties have not been investigated. In this paper is described the determination of the free energy and heat of formation of the compound CdSb, which is of the first class mentioned above, melting congruently at 455&apos; C. This compound shows a rhombic structure, and the lengths of the edges of the elementary cell containing four molecules are: a = 6.52, b = 8.60, c = 4.16 A.&apos; There are three possible methods of determining the free energy of formation of a compound of this type. The first method, applying the third law of thermodynamics, requires the measurement of its heat capacity preferably to liquid hydrogen temperatures, and a calorimetric determination of its heat of formation. The second method involves the study of the equilibrium of the compound in some gas reaction, such as: CdSb + CO² = CdO + CO + Sb From the known free energies of formation of CdO, CO² and CO the free energy of formation of CdSb could be calculated. The third method measures the electromotive force of a galvanic cell in which the cell reaction is the reversible formation of the compound from the elements. The first method is generally applicable, but requires elaborate experimental equipment. The second method can not be used for compounds melting at low temperatures, owing to the difficulty in establishing equilibrium. The electromotive force method, therefore, seemed to offer

Jan 1, 1935

[Alphabetic Section: The letter immediately following a member&apos;s name indicates grade: M-member, A-associate, J-junior. The numerals following member&apos;s grade indicate year of election. The letter following year of election indicates primary divisional affiliation: A. Mining & Exploration F. Coal B. Minerals Beneficiation G. Petroleum C. Iron and Steel H. Industrial Minerals D. Extractive Metallurgy J. Council of Education E. Institute of Metals K. Council of Economics Geographic Section: An asterisk (*) preceding a member&apos;s name indicates availability for consulting work:]

Jan 1, 1961

The American Museum of Safety has installed a large collection of exhibits at 18 West 24th St., New York City, and extends a cordial invitation to the members of the Institute to visit this exhibition. The Museum is open daily from 9 am. until 5 p.m., and special arrangements will be made for the admission of a large party in the evening. The exhibition covers all phases of industrial and general safety, and also the important questions of sanitation and hygiene.

Jan 2, 1917

By Cecil Desch

THIS annual lecture, under the auspices of the Institute of Metals Division, and which was illus- trated by lantern slides, has been printed in full and a limited number are available for distribution on request. Some excerpts from the lecture are given below: Ever since the simple geometrical relations of crystals were discovered, it has been recognized that their proper-ties are best explained by assuming that their ultimate particles are arranged on a space lattice, and that the char-acteristics of that lattice determine the shape of the crystal and its physical and mechanical properties. Modern ex-amination by means of X-rays has widened that concep-tion and given it greater; definiteness, and the atoms are now regarded as the particles forming the space lattice. The splendid achievements of investigators in this field have made it possible to state, for a large number of sub-stances, the form and dimensions of the lattice. The char-acteristic of a lattice is that a unit of simple geometrical form is repeated at regular intervals in three dimensions so as to fill the entire crystal. It follows that there must be certain planes in which the atoms are more closely packed than in planes drawn at any angle to them, and it is these planes of closest packing which play the greatest part in determining the growth and other properties of the crystal. There are actually two stages in crystallization, what-ever be the medium in which it occurs. The first is the ap-pearance of crystal nuclei; the second the growth of those nuclei to form crystals of appreciable .size. The first is clearly a kinetic phenomenon. In the molten mass, solu-tion, or vapor, the molecules are in a state of rapid motion and frequent collision. When the temperature has fallen so far. that it is possible for a crystal to exist, a few col-liding molecules may fail to rebound, and so become at-tached to one another, the balance between the attracting and repelling forces-between them causing them to arrange themselves on a space lattice, to which other molecules sub-sequently attach themselves. It was once maintained that the X-ray evidence demanded that the molecule should dis-appear in the solid crystal, but this was a wrong inference, and in many crystals, but not in all, the chemical molecule retains its identity in the solid state. In pure metals the atom and the molecule are identical, so that the conditions are unusually simple. How many. nuclei will be formed in a given mass is evi-dently a problem in probability. Experiments to deter-mine the relation between the temperature and the number of nuclei formed in a given time have been made with some success by using viscous organic substances, but metals offer much greater difficulties, and the few determinations which have been published are vitiated by serious errors. However, the examination of sections of ingots of the same composition and cast at &apos;the same temperature in similar molds will show, that the number of crystals does not vary widely.

Jan 3, 1927

By M. J. Pool, P. J. Spencer

Using liquid tin as the solvent metal, the heats of solution of silver and gold in dilute Ag-Au-Sn alloys have been determined at 723°K by solution calorimetry. From the values obtained, the various enthalpy interaction coefficients in the liquid solutions have been calculated. The self-interaction coefficients Au and Ag values of 2413 and -6322 cal per g-atom in binary Au-Sn and Ag-Sn alloys, respectively. For an alloy containing 0.04 mole fraction Ag, Au is equal to 2443 cal per g-atom, and in an alloy containing 0.04 mole fraction Au, Ag has a value of —8883 cal per g-atom. Ag Au has been determined as —2650 cal per g-atom. ADDITION of a second solute to a dilute binary alloy may cause striking changes in the thermodynamic characteristics of the alloy. As yet, such influences cannot be reliably predicted and it is only by accumulation and critical assessment of data that definite patterns can be established. Solute interactions in dilute solutions were first treated mathematically by Wagner,1 who derived expressions for the Gibbs energy interaction coefficients. For an alloy consisting of. two dilute solutes, i and j, in a solvent s, these coefficients are given by: where yi is the activity coefficient of component i and x represents the mole fraction of solute or solvent. Other interaction coefficients have since been established in terms of the various partial molar thermodynamic properties of an alloy; the definitions of these are summarized in a recent paper by Lupis and Elliott.2 Mathematical and experimental studies of such coefficients have received much attention recently, providing a very useful theoretical background to an understanding of the nature of solute interactions taking place in dilute solutions. One of the definitions to arise from such work has been the extension of Wagner&apos;s treatment by Lupis and Elliott4 to include an enthalpy interaction coefficient, defined as. where ?Hi is the relative partial molar enthalpy of component i. ?Hi is related to the relative partial molar enthalpy at infinite dilution, ?Hio, and to the enthalpy interaction coefficients by the expression: Values of ?Hi can often be obtained with a high degree of accuracy by calorimetry, and, if the composition of the alloy is carefully controlled by making calculated solute additions throughout a series of measurements, application of Eq. [2] will enable reliable enthalpy interaction coefficients to be determined. Partial heats of solution must be investigated as a function of solute concentrations down to xi = 0, and, since ? values are obtained from the slope of mi plotted against x, great care must be taken to obtain precise data. The data for binary systems which are presently available often require extrapolation of ?Hi values from compositions as great as xi = 0.05 or even 0.1 to obtain limiting heats of solution. Reliable enthalpy interaction coefficients are thus impossible to obtain from published data for most of the alloy systems already investigated. The aim of the present work was to determine values of Au, Ag, Ag, and Au in the limit xsn -1 for the relatively simple Ag-Au-Sn system and from these results to gain some insight into the possible influence

Jan 1, 1969

By H. T. Clark

Within the last twenty years at least three sets of lattice constants for the room temperature (alpha, hexagonal close packed) phase of titanium have been reported in the literature. These values, summarized in Table 1, differ one from another by amounts far greater than can be explained on the basis of inaccuracies in parameter measurements. This paper presents new values determined for high purity titanium. It also details the effect of two elements, oxygen and nitrogen, on these parameters and shows that two of the previously reported values are probably in error because of the presence of one or both of these elements in the material used for examination. Preparation of Samples The titanium+ used for this study was prepared by the thermal decomposition of titanium tetraiodide7 on a hot titanium filament. This titanium rod was prepared for X ray examination by melting about 10 g in purified argon in an electric arc furnace on a cold hearth. This cast button was cold rolled to 0.040 in. thick sheet, cleaned, annealed in vacuum at 1000°C and cold rolled to 0.020 in. thickness. About 0.003 in. of surface material was then removed by hand grinding on papers to remove any contamination caused by the rolls and the sample was bent to the radius of the focusing camera. The sample was then vacuum annealed at 600°C, a temperature just high enough to cause recrystallization, producing a fine grained structure. Such a structure is essential in sheet specimens prepared for focusing cameras in order to have a sufficient quantity of grains to develop continuous diffraction lines. The use of sheet specimens rather than powder samples appears to be essential for the X ray examination of titanium. This is because of titanium&apos;s exceptionally high gettering power and its rapid absorption of adsorbed gases, water -vapor, and the like at annealing temperatures. While the effect of this contamination may be neglected for sheet specimens, its effect on 200-300 mesh powder is appreciable. Titanium alloys of oxygen and nitrogen were prepared by a technique simi- lar to that described above except that the required amount of the highest purity titanium oxide or nitride available was added prior to melting in the arc furnace. These materials were added by placing them in holes drilled in the titanium. A small weight loss invariably occurs during the melting of these oxygen and nitrogen alloys. This is believed to be due entirely to the loss of some of the powdered compound in the blast of the electric arc, an assumption which is justified on the basis that there is no weight loss during the melting of titanium metal and that wet analyses for nitrogen on representative samples have checked with the calculated analyses when it was assumed that the entire loss during melting was due to the loss of titanium nitride powder. These alloy buttons were reduced to sheet in the same manner as used for the unalloyed titanium. Experimental Procedure A North American Phillips 12 cm diam symmetrical precision focusing vacuum camera and copper radiation

Jan 1, 1950

By Woolsey McA. Johnson

Independently of the recognized chemical reactions involved in the production of metallic zinc, the process is affected by physical conditions in efficiency, and by commercial as well as technical economy. To offer some observations concerning these conditions is the purpose of the present paper. Among the important elements of this problem is the physical nature of the particles constituting the mass of zinc oxide to be reduced. This may be the result, either of the manner of the original deposition of the mineral, or of the treatment to which it has been subjected in the roasting-furnace. The physical character of the reducing-agent is another important factor, since the carbon of some coals is much more active in reduction than that of others. The degree of fineness, whether of ore or coal, or both, likewise plays a significant part. These factors, together with the physical admixture of foreign substances with the ore, may give rise also to chemical " side-reactions," sometimes hindering or retarding, and sometimes accelerating, the reduction. Finally, thermal conditions, including the relative conductivity of the materials, deserve to be taken into account. In firing a furnace with retorts charged with a mixture of roasted ore and coal, the first reaction is naturally the boiling-off of the contained water; the next is the distillation of the light hydrocarbons from the coal; the next is the reduction of the iron oxide to protoxide and sub-oxide successively, and then to metallic sponge; and the final reaction is the reduction of the zinc oxide in the ore by the carbon to metallic zinc. This reaction commences at 1,022o to 1,060o C., according to the physical nature and condition of the coal and ore. Since the retort and the charge are far from being good con-

Jan 1, 1908