Search Documents

Use of rock grinding media in a mill at Tennessee Copper Corp. was mentioned in the MINING ENGINEERING Annual Review. (February 1953, page 158). Because interest in use of self-grinding media continues high we asked F. M. Lewis, Superintendent of Concentration at Tennessee Copper, to supply more details on this trial, and of plans to expand use of rock media in their mills that grind marble. Here is what he reports.

Jan 5, 1953

By Myron Read

DURING the past 25 years, mining engineers have seen the development of a multitude of specialized engineering curricula in the mineral industry field. Bachelor degrees are now !ranted in the fields of mineral dressing petroleum engineering, geological engineering, fuel technology, and many others. These fields were all, previously considered to be part of a mining enginieer's work and elementary phases of them were included in mining engineering curricula. Their emergence has left some mining engineers with the fear that nothing will he left for a purely mining engineer to teach, or that mining engineering graduates will be unable to complete in any of these fields with the more specialized students and thus will have neatly restricted employment opportunies. A secondary reaction has been that if students who began to say that the pining engineering curriculum taught everything but mining, since so many of :he subjects that had always been udedAuded in the mining engineering curriculum now were fields in their own right.

Jan 1, 1946

By Heinrich Ries

In another place,* the writer has called attention to the modern methods of the laboratory investigation of clay, and it is desired here simply to discuss one branch of the subject, which, though of considerable importance, has heretofore received little attention in this country, viz., the rational analysis of clay. In order, however, the better to point out the bearings and advantages of this procedure, it is necessary to refer briefly to the ultimate analysis as well. The remarks in this paper refer only to the use of clay for the manufacture of clay-products. Pure clay or kaolin-f is extremely refractory, possesses little plasticity, and usually shrinks aud warps considerably in burning. Even the smallest proportion of impurities changes these properties, so that the kaolin exhibits variations in shrinkage, plasticity, tensile strength, fusibility, and often color when burned. The majority of nearly pure kaolins consist of kaolinite (A1,O2 2SiO,, 2H20), undecomposed feldspar, and quartz. The kaolinite generally forms the finest particles of the clay and is known as the clay-substance, while the rest of the clay-particles are collectively spoken of as sand. In the ordinary or ultimate analysis, the substances generally determined are silica, alumina, ferric oxide, lime, magnesia, alkalies and water. An analysis of this type simply regards the clay as a mixture of elements or oxides, but gives no clue as to the actual condition in which these substances exist, i.e., whether as silicates, oxides or carbonates, etc., a point which it is of the highest importance to know; for the individual components of the clay influence its properties not only according

Jan 1, 1899

By M. B. Bever, A. K. Jena

THE heats of formation ?H at 273°K of the compound AgMg as a function of composition have been measured by solution calorimetry.1 The value at the stoichiometric composition is -4.41 kcal per g-atom. From electromotive force measurements2'3 the heat of formation at 773°K of stoichiometric AgMg has been determined as -5.19 kcal per g-atom.4 The combination of these two values results in an unusually high negative temperature coefficient of the heat of formation d?H/dT = ?Cp = -1.6 cal per g-atom-OK. By contrast, published heat contents of the compound AgMg and the component elements above room temperature5 indicate that the temperature coefficient of the heat of formation of AgMg is nearly zero. In this communication calorimetrically measured heats of formation of A.K.JENA,Junior- MemberAIME,andM.B. BEVER,Member AIME, are Staff Member, Division of Sponsored Research, and Professor of Metallurgy, respectively, Massachusetts Institute of Technology, Cambridge, Mass. Manuscript submitted July 1, 1968. IMD AgMg below room temperature are reported and the temperature dependence of the heat of formation is discussed. The heat effects of additions of samples of the compound AgMg containing 50.1 at. pct Mg to liquid tin-rich solutions at 623°K were measured in a solution Calorimeter.6 The heat effects of additions plotted against the average of the atom fractions of solutes in the solution before and after each addition were a linear function of composition from which the heat effect at infinite dilution was obtained, Table I. The calorimeter was calibrated by additions of tin; the heat content (H623°K - H273°K) of tin was taken as 4.08 kcal per g-atom.4 The heat effect at infinite dilution of an addition of where heat of formation of AgMg at T°K, T = temperature from which samples are added (78°, 195°. and 273°K), Xi = atom fraction of i in AgMg, ?Hi = relative partial gram-atomic enthalpy of i in tin-rich solution.

Jan 1, 1969

By J. W. Fuller

DURING the last 20 years, experimenters have sought to utilize pulverized coal in boiler plants, but refractory and slag troubles have usually overbalanced any, gains in efficiency that were obtained. These troubles were caused largely by lack of knowledge of the proper methods of coal preparation and lack of a furnace design that would be adaptable to pulverized-coal firing. When this information was obtained the results were so much more satisfactory that within the last 5 years approximately, 80,000 boiler hp. have been installed in plants ranging from 1000 to 20,000 boiler hp. rated capacity, which are operating at an average of 174 per cent. of rating. The first commercial installation for burning pulverized coal under boilers was made at the Parsons shops of the M. K. & T. railroad in 1916. Of eight 250-hp. water-tube boilers thus fitted, six were operated continuously for 3 yr., when oil was obtained at such a low price as to warrant its use. Since then, this plant has been operating alternately on pulverized coal and oil, depending on prevailing prices. Recently gas has been discovered within 20 mi. of this plant, so that this fuel may also be used. No change in furnace design was made when changing from pulverized coal to oil or gas firing. One of the principal advantages of this method of firing is its ability to utilize, with maximum efficiency, all kinds of coal, irrespective of quality or physical characteristics. In fact, quite a number of the present pulverized-coal installations were made for the purpose of utilizing coal that could not be marketed or used in any other way. The Pacific, Coast Coal Co., at Black Diamond, Wash., formerly hand fired the boilers, using approximately 125 tons of prepared steam-size coal daily. The Black Diamond steam coal is the best quality of coal for steaming purposes mined in that section of the country, and there is a market for all that can be produced. By installing a pulverizing plant, it was possible to substitute coal of a size and quality that had no commercial value, so that 125 tons daily of the best steam coal formerly used at the mines is now marketed.

Jan 12, 1921

State of California, Division of Mines, Ferry bldg., San Francisco, Calif. Walter W. Bradley, State Mineralogist. A list of publications available will be sent upon request. Bulletin 77 is a list of publications complete from 1880 to 1917 and contains synopses It is sent free. Bulletin 105, California mineral production and directory of mineral producers for 1930, brings the complete list up to date, sent free on request The Division of Mines issues principally (1) A series of Reports, (2) Bulletins, (3) Preliminary Reports, and (4) maps. The Reports were first issued biennially, later annually, and for the past few years they have taken the form of quarterly reports. The yearly subscription price for the quarterly reports is $1, payable in advance Reports and separate chapters available are Report 2, First Biennial (1892), $1, 14 (1913-1914), Chapter on mines and mineral resources of Colusa, Glenn, Lake, Mann, Napa, Solano, Sonoma, and Yolo counties, 50 cents, 15 (1915?1916), Mines and mineral resources of Butte, Lassen, Modoc, Sutter and Tehama counties, 50 cents, and Mines and mineral resources of Monterey, San Benito, San Luis Obispo, Santa Barbara and Ventura counties, 65 cents, 16 (1917-1918), Nevada County, 75 cents, Plumas County, 50 cents, Sierra County, 50 cents; 17 (1920), Mining in California during 1920, $1 75, 18 (1922), Mining m California, chapters for Aug , Sept , Oct , Dec , free, 19 (1923), Mining in California, chapters for Jan , Feb , Mar, Sept , free, 20 (1924), Quarterly chapters on mining in California (except July, out of print), 25 cents, 21 (1925), Quarterly chapters containing county reports- Jan (Sarcramento, Monterey, Orange) 25 cents, April (Calaveras, Merced, San Joaquin, Stanislaus, Ventura), 25 cents, July (Del Norte, Humboldt, San Diego) 25 cents, Oct (Siskiyou, San Luis Obispo, Santa Barbara), 25 cents; 22 (1926), Quarterly county reports: Jan. (Santa Cruz, Trinity), 25 cents, April (Shasta, San Benito, Imperial), 25 cents, July (Mann, Sonoma) and Copper in California, 25 cents, Oct (El Dorado, Inyo) Minarets District, 25 cents, 23 (1927), Quarterly county reports- Jan (Contra Costa), 25 cents, April (Aniador, Solano) Bibliography of clay

Jan 1, 1933

By A. R. Jr. Amos

LOG washers have been used for many years in the washing of clay iron ores, phosphate rock and manganese ores, but not until the past 15 years have they been employed to any extent in the preparation of aggregate materials and fluxing stone. For a machine of such importance where tenacious clay or soft rock must be eliminated, there are few data generally available. The purpose of this paper is to set forth the results obtained from several operations, together with a few suggestions for planning a specific installation. Where the material to be washed out consists of loose surface soil, silt, or small amounts of quickly soluble clay, there is little competition with other forms of washers, because greater power and maintenance are required for the operation of log washers, but where the foreign matter is a stiff clay, such as occurs with high-calcium limestones and in marginal gravel deposits, the ability of other kinds of washers to eliminate com-pletely the hard clay balls is at least uncertain. Then the log washer comes into its own field, for with the breaking and churning action of the logs it will clean out the toughest clay. Even with material from the hydraulic dredge, if it contains tough clay, the log washer is desirable unless the gravel is subjected to a costly soaking and rehandling process. Recently there has been a considerable development in other types of machines to accomplish these results but it is not within the scope of this paper to make comparisons between competitive types, but to present the best obtainable data on log washers only. From the primitive design that gave it its name, a long log hewn from a tree, with paddles forged to shape from strap iron and attached by lag screws, the log washer has gradually been developed to the present all-steel type. As now manufactured, the log washer consists essentially of two built-up logs on which are mounted a series of paddles, carried by shafts fitted at the ends of the logs on bearings fastened outside the enclosing steel box, or trough, which is set at an angle of about 5° to 10° and into which the material is fed. Stuffing boxes at the places where the shafts pass through the box at the lower end are equipped with water-

Jan 1, 1936

By W. H. Adams

One of the most attractive subjects for technical writers is the gigantic industry of the manufacture of sulphuric acid. This is no doubt, natural when we take into account that it has grown in this country during the past twenty years, from a production of 60,000 tons in the year 1867, to that of nearly 450,000 tons in 1887. We may well excuse much of the literature which but repeats the same old story, as it serves to bring to the public notice, at proper intervals, the hidden resources of our land; and this constant application of essential truths will sooner or later be the means of freeing us from dependence upon the Old World for necessary chemical products. The present increase in manufacture of this acid in the United States is almost wholly from pyrites ores, which we have in unlimited quantities close at hand. The largest consumption of such acid is for treatment of other native products, petroleum, rock-phosphates, etc.; and, considering the knowledge we have gained during the past twenty years, it is safe to say that the industry is but fairly established, and the causes which have operated to place us in our present proud position are but natural incentives for a further growth and an increased consumption of the many other undiscovered or undeveloped resources of our American soi1. In one of his earlier editions Muspratt says: " It would seem that the manufacture of sulphuric acid, though as extensively carried on as any other business, yet seems to be the least understood; and the ignorance of some manufacturers appears to be only equalled by that of writers, who, in their description of the production of this acid, give figures of apparatus, and vaunt as improvements, things which have been exploded for years. It is possible to find in the works of eminent men drawings of apparatus, for the production of sulphuric acid, which never could possibly have worked one day—some, in fact, could never have worked at all."

Jan 1, 1888

By A. J. Williams

THE province of Saskatchewan, situated in the center of the Great Plains region of Canada, has, like most prairie areas, an essentially agricultural economy. Most of its population of about 860,000 is located in the southern half of the province in the farming and ranching areas. To the north of the prairie is a broad forested belt supporting a considerable timbering industry, and the northern one third of the province is glaciated pre-Cambrian rock formation. This latter area is, relatively barren of vegetation, but the presence within it of a considerable variety of radioactive, noble and base metals, and industrial minerals has been shown by prospecting in recent years.1 Glacial Geology The Keewatin ice sheet, considered to have accumulated in the country to the west of Hudson Bay in Pleistocene time, covered at its maximum advancement almost all of Saskatchewan and extended south of the international boundary. Only in the Cypress Hills in the southwest and around Wood Mountain in the south central portion of the province did the preglacial formations escape the action for this glacial period. The bedrock of the plains and forest areas therefore is overlain by moraines and modified glacial drift, which vary in thickness from a few feet to 400 or 500 ft.2 Glacial action in the pre-Cambrian area of the province was largely erosional, most of the more recent formations and some of the pre-Cambrian rock being transported out of the area to the south and west. It has been estimated that about 13 pct of this area is composed of lakes and rivers not too adaptable to rail or water transportation, so that until the use of aviation for exploration purposes became general; development of the area was slow. To the south, the heavy. mantle of glacial drift has to some extent deterred the discovery of industrial minerals in the bedrock underlying the forest and prairie regions.3 At the same time, this drift contains numerous deposits of those most elementary and necessary industrial minerals, sand and gravel. Sedimentary Basin The major feature of the sedimentary deposits underlying the plains regions is the basinal structure known as the Moose Jaw syncline, which runs from the southeast corner of the province in a northwesterly direction. To the west. of this syncline the formations curve upward, then have been faulted and further upthrust to appear at the surface in the foothills of-the Rockies in Alberta; to the east and north they curve upward into Manitoba and northern Saskatchewan, but the surface contacts are covered mostly with glacial drift.2,3 The axis of the syncline dips to thee southeast, so that there is also an upward trend of the formations along the axis to the northwest. In illustration of the regional structure underlying the province, the pre-Cambrian basement has been logged in drillholes at the following depths in several locations: Ogema (south central), 9390 ft; Gronlid (northeast), 2599 ft; Vera (northwest), 4422 ft; Big River (north northwest), 2348 ft. Fig. 1 indicates the general surface geology of the province, ignoring such glacial overburden as may overlie many of the bedrock formations. Also indicated is the approximate location of the axis of the Moose Jaw syncline.4 Industrial Minerals Clays: The province is fortunate in possessing a widespread distribution of clays of ceramic value, ranging from those used for heavy structural products to the high grade pottery and china clays. Shales suitable for brick and tile production are found in the Upper Cretaceous and Tertiary formations across the south of the province where the glacial drift is thin or nonexistent. Many deposits of glacial lake clays suitable for such wares are found scattered over the rest of the province south of the pre-Cambrian area. The Whitemud formation of the Upper Cretaceous is a narrow sedimentary, band of secondary clays found intermittently, at points, across the, south of the province where glacial action did not disturb or remove them.8 In the southwest corner of the province, around Eastend in the Frenchman River valley, the refractory clays of this formation are contaminated somewhat with iron compounds or other alteration products of basaltic rocks. This eliminates the use of those clays in true whitewares, as they fire to creamy buff shades at the lower temperatures and to a blue-specked grey at cone 8 to 12, (2280°F to. 2390°F), the range commonly used in firing whiteware. However, for use in the production of colored artware, caneware, stoneware or crockery, and sewerpipe, this type of clay makes an excellent body that requires little or no addition of flint, feldspar, or other fluxing materials such as are required in the higher class of ware.9 It is not a grade of clay that can be shipped great distances to the manufacturing centers, but a market for considerable tonnages has developed at nearby Medicine Hat, where cheap natural gas is available for the firing of the ware. Farther east in the south central portion of the province, the clays of the Whitemud formation are generally more refractory and white burning. The formation is divided into three zones, consisting of white clays, brown shale, and white sandy clays.

Jan 1, 1952

By Cleveland Dodge

THE present organization of Copper Queen employ-ees, known as the Employees' Conference Com-mittee, is really an outgrowth of the former Grievance Committee, which, in turn, had developed from the original Hospital Committee. The relatively small membership of these older organizations, the practical limitation of their activities to the presenting of grievances, and their lack of initiating powers, were the principal defects which the plan now in operation seeks to overcome. A somewhat parallel scheme was instituted in our Sacramento Hill division about four years ago; this gradually developed into the Ways and Means Committee, which, in addition to providing a forum for the discussion of operating problems, was instrumental in establishing an excellent and mutually satisfactory bonus system. Before recommending adoption of the plan now in force, we made extensive inquiries among those who have had any experience in such matters, and ended by proposing a modification of a scheme developed by John Leitch,1 which was characterized by its similarity to the constitution of the Federal Government. As finally remodeled, the. plan was submitted to vote of the entire working forces at the Copper Queen mines, and was adopted by them in May, 1920. Mining opera-tions since that date have been so interrupted that it is scarcely possible to state exactly what the results have been. The following quotations are from a printed pamphlet containing the constitution of the organization, as finally adopted. The first extract is from a letter addressed by the management to the employees: The plan submitted for your approval and adoption is modeled after the constitution of our own country, under which every individual is given an opportunity for advancement, according to his ability and determination, and every citizen is given a voice in the laws that shall govern him. So it is to encourage the individual employee in advancement, and to give him a voice in making the rules that shall govern his conduct, that we favor the adoption of the proposed constitution.

Jan 1, 1923

By J. R. CAIN

SAMUEL L. HOYT, ? Nela Park, Cleveland, Ohio (written discussion?). The work that Dr. Cain is doing on gases in steel should have a highly important bearing on investigational work in connection with steel-making practice. We found, for example, in our work in connection with the use of manganese in open-hearth practice that we needed expressions for the manganese efficiency and the "condition" of the steel. To get these figures we assumed that we would need to know the amount of FeO at different stages of the heat and the amounts of the gases present. This required simultaneous analyses of our samples for FeO and the gases and Dr. Cain seems to be the only investigator who has considered the analytical work from this point of view. That he has done so is very encouraging and it is to be hoped that his work will solve the mys-teries now surrounding this neglected phase of steel metallurgy. Those interested in the Ledebur method for use in connection with the efficiency of manganese as a "deoxidizing " agent will he disappointed to learn that more recent work at the Bureau indicates that Ledebur determinations are not reliable. The principal source of error seems to be due to the partial reduction of the ferrous oxide by the carbon present in the steel. However, it seems like an unnecessary criticism of the Ledebur method to state (p. 1319) that it proved of little value because it showed little differences in oxygen for a series of steels treated with ,various reagents and showing variations in physical properties and free-

Jan 12, 1919

By Joseph E. Pogue

THERE are two methods employed in the development of oil pools. The older and dominant method is one in which the primary object is the protection of the underground deposit from drainage through competing wells, and considerations of efficiency of extraction and cost of production are subordinated thereto. The newer and less prevalent method is one in which maximum efficiency and minimum cost are the first objectives and developments to these ends may proceed undisturbed by the exigencies of competitive drainage. The second method has developed mainly in pools under single ownership and the term "unit operation" has come to be applied to this procedure. A single ownership, however, is not essential to the method, for unity of operation may be achieved by agreement under split ownership, or even by a concert of enlightened purpose. There are examples of unit operation where neither the ownership nor the management is a unit, but merely where unity of procedure has been attained, as is the case of the Yates pool. .Throughout this paper unit operation is used in its broad sense without implying sole ownership or single management, although unit operation is more conveniently attained where these conditions are present.

Jan 1, 1930

By A. L. Foell

The development of the modern blast furnace began more than one hundred years ago, with the abandonment of the small hillside furnaces. Its development, especially during the past 50 years, has been accomplished through a rapid succession of enlargements and improvements. The remarkable growth in furnace output during this period is a tribute to the engineers and operators who have constantly endeavored to build larger and more efficient blast furnaces. The blast-furnace operators and their mechanical and electrical maintenance staffs have originated most of the furnace improvements as a result of their practical operating experience. Furnace Lines About 50 years ago furnaces consisted of hearths about 11 ft. in diameter, which merged into rather high flat boshes, with no cylindrical section between the bosh and inwall and no cylindrical section at the stock line. Since then the lines of the furnace invariably have included a cylindrical section above the bosh and a cylindrical section at the stock line. Notable increases have been made in both hearth diameters and furnace heights. During the past 10 years hearth diameters in new and replaced furnace stacks have rather consistently fallen within the range of 25 to 28 ft. while their heights have varied be- tween 100 and 106 ft. The lines of most large furnaces using Mesabi ores have followed a fairly uniform pattern (Fig. I) in which the principal dimensions for 25-ft. hearth furnaces are as follows: Hearth diameter............... 25 it. o in. Height of bosh................. 10 ft. o in. Bosh angle.................... 81 1/2º Diameter top of bosh........... 28 ft. 0 in. Inwall batter per foot........... 15/16 Stock-line diameter............. 19 ft. 6 in. Large-bell diameter............. 14ft. 6 in. Height from iron notch to top ring casting...................... 100 ft. o in. In determining the size of a new furnace for the replacement of an existing stack or for an addition to productive capacity, it is not possible to formulate a procedure that can always be followed. Local conditions, requirements as to capacity, available raw materials and prospects for future expansion dictate the size of such proposed improvements or additions. However, where the immediate requirements indicate a stack or furnace of a certain productive capacity, and the future prospects indicate that more capacity can be utilized, it is well to consider building the furnace ior the ultimate capacity rather than to install a smaller hearth with provision for future enlargement. The decision to build the larger hearth and stack for the ultimate capacity probably will require no greater initial investment, since the saving in the cost of brickwork will about offset the greater cost of the hearth jacket, tuyere breast and bosh bands. In the meantime. the furnace of larger hearth dimensions, while operating below its ultimate output, will yield a better coke rate and

Jan 1, 1943

By A. L. Foell

The development of the modern blast furnace began more than one hundred years ago, with the abandonment of the small hillside furnaces. Its development, especially during the past 50 years, has been accomplished through a rapid succession of enlargements and improvements. The remarkable growth in furnace output during this period is a tribute to the engineers and operators who have constantly endeavored to build larger and more efficient blast furnaces. The blast-furnace operators and their mechanical and electrical maintenance staffs have originated most of the furnace improvements as a result of their practical operating experience. Furnace Lines About 50 years ago furnaces consisted of hearths about 11 ft. in diameter, which merged into rather high flat boshes, with no cylindrical section between the bosh and inwall and no cylindrical section at the stock line. Since then the lines of the furnace invariably have included a cylindrical section above the bosh and a cylindrical section at the stock line. Notable increases have been made in both hearth diameters and furnace heights. During the past 10 years hearth diameters in new and replaced furnace stacks have rather consistently fallen within the range of 25 to 28 ft. while their heights have varied be- tween 100 and 106 ft. The lines of most large furnaces using Mesabi ores have followed a fairly uniform pattern (Fig. I) in which the principal dimensions for 25-ft. hearth furnaces are as follows: Hearth diameter............... 25 it. o in. Height of bosh................. 10 ft. o in. Bosh angle.................... 81 1/2º Diameter top of bosh........... 28 ft. 0 in. Inwall batter per foot........... 15/16 Stock-line diameter............. 19 ft. 6 in. Large-bell diameter............. 14ft. 6 in. Height from iron notch to top ring casting...................... 100 ft. o in. In determining the size of a new furnace for the replacement of an existing stack or for an addition to productive capacity, it is not possible to formulate a procedure that can always be followed. Local conditions, requirements as to capacity, available raw materials and prospects for future expansion dictate the size of such proposed improvements or additions. However, where the immediate requirements indicate a stack or furnace of a certain productive capacity, and the future prospects indicate that more capacity can be utilized, it is well to consider building the furnace ior the ultimate capacity rather than to install a smaller hearth with provision for future enlargement. The decision to build the larger hearth and stack for the ultimate capacity probably will require no greater initial investment, since the saving in the cost of brickwork will about offset the greater cost of the hearth jacket, tuyere breast and bosh bands. In the meantime. the furnace of larger hearth dimensions, while operating below its ultimate output, will yield a better coke rate and

Jan 1, 1943

By B. M. Larsen, T. E. Brower

IN an earlier paper1 we discussed a simple, rapid method of taking samples of liquid steel and analyzing them for oxygen, which, though possibly not absolutely accurate (as is likewise true of all other methods), certainly yields results that are satisfactorily consistent. Accordingly, samples from hundreds of heats in different shops were analyzed for oxygen, with results sufficient in number to be handled statistically and permit estimation of some general trends. Measurements were made in acid as well as in basic open hearths, throughout the refining period, to learn how stirring, blocking, adding ore or lime or sand, affects the oxygen content of the bath; we also followed the changes brought about by tapping, teeming, and deoxidizing. Some of these results, discussed in an earlier paper.2 bring out the dominant role of the carbon-oxygen reaction in regulating degree of oxidation both of metal and of slag, also the marked variability of concentration of dissolved oxygen [0] in excess of that which would be in equilibrium with carbon and with carbon monoxide at a partial pressure of one atmosphere. As a logical beginning on this complex problem, we take up in the present paper the variability of this excess oxygen, ?[O], when other factors are as constant as they ever are in open-hearth operation; namely, toward the end of the refining period, when the bath may be regarded as in the comparatively steady state it approaches in absence of disturbing factors. This condition was chosen because by that time the significant reactions, except carbon oxidation, between slag and metal have come to substantial equilibrium; this facilitates interpretation of the complex situation and thus permits more definite conclusions to be drawn. This excess concentration of oxygen, ?[0], in the metal is needed, of course, to make the steelmaking process go at a reasonable rate; alternatively it may be regarded as a measure of the virtual pressure increment above one atmosphere, or of the degree of supersaturation, of carbon monoxide in the metal. According to our measurements, the excess concentration ?[O] in liquid steel varies from about 0.009 to 0.035 per cent oxygen by weight. It is quite sensitive to change of conditions, being altered temporarily by operations such as stirring with green poles, additions of ore, lime, or sand; but as the disturbance works itself out, it resumes a level within the intermediate range characteristic of the steady state. The conditions most common in average furnace practice are covered by the following : [ ] as in a reasonably steady state-that is, when it is boiling normally, is at proper temperature with a well-shaped slag, and has been free from disturbing effects during the preceding half hour-?[O] returns from

Jan 1, 1946

By J. O. Lewis

The operation of gas-condensate fields is comparatively new and involves physical principles with which the industry was not prcviously familiar. It has been necessary to devise methods for testing gas-condensate wells and to correlate laboratory and field data. In this paper new methods are advanced for interpreting well G.P.M.† tests whereby dilution by dry gas can be estimated and information supplied on revaporization of condensates by dry gas. Inaccuracies in well test data are discussed. Changes in flow rates can cause changes in the G.P.M. of the effluent and it may take some time for a well to become stabilized after an important change in flow rate. Retrograde tests as usually conducted cannot be directly compared with field G.P.M. data, because the retrograde tests usually include solution gas in the condensates, which are reported On the cumulative basis whereas field data (G.P.M.) usually report pentaneS PlUS on a rate or instantaneous basis. Introduction Though long known to physicists, the phenomena Of retrograde condensation became known to the oil and gas industry Only in recent years, when deeper drilling disclosed that the behavior of vapors under changing pressures was different in high-pressure reservoirs than under the low-pressure operations with which the industry was familiar. These deep, high-pressure reservoirs in which condensation and vaporization behaved inversely to the accustomed manner became known as "gas-distillate," or preferably "gas-condensate" fields. Partly to prevent precipitation and retention of liquids in the reservoir, but still more to prevent the waste of residue gas, the operation known as "recycling," or preferably "cycling," was instituted, in which the residue gas is reinjected into the reservoir, thus maintaining pressure and driving the wet gas to the producing wells. For lack of field experience to serve as a guide, the industry had to assume that theory and laboratory experiments could accurately forecast retrograde behaviors in operating these gas-condensate fields, but it is obvious that these assumptions should be checked at the first opportunities against actual field experience. To make such checks, it is necessary to accumulate a large quantity of reliable field data, but experience has shown that it is difficult to obtain reliable field data and that the laboratory data as usually presented are not in directly comparable form. The problems of correlation involve the complex phase behavior on the one hand, and a knowledge of field data and a visualization of underground conditions on the other hand. This paper is an approach from field experience, The purposes of this article are to discuss the sources of uncertainty in the data and to present methods of analyzing, interpreting and correlating laboratory and field data. Data mostly from lower Gulf Coast fields are presented, from which some conclusions can be derived, but better data from more sources than those available to the writer will be required before satisfactory answers to many questions can be obtained. This paper is presented to stimulate the analysis and publication of data from other fields, the reexamination of field and laboratory methods, and the taking of more complete and reliable field tests. For these purposes, the writer presents some speculations that otherwise would not be appropriate.

Jan 1, 1947

By J. O. Lewis

The operation of gas-condensate fields is comparatively new and involves physical principles with which the industry was not prcviously familiar. It has been necessary to devise methods for testing gas-condensate wells and to correlate laboratory and field data. In this paper new methods are advanced for interpreting well G.P.M.† tests whereby dilution by dry gas can be estimated and information supplied on revaporization of condensates by dry gas. Inaccuracies in well test data are discussed. Changes in flow rates can cause changes in the G.P.M. of the effluent and it may take some time for a well to become stabilized after an important change in flow rate. Retrograde tests as usually conducted cannot be directly compared with field G.P.M. data, because the retrograde tests usually include solution gas in the condensates, which are reported On the cumulative basis whereas field data (G.P.M.) usually report pentaneS PlUS on a rate or instantaneous basis. Introduction Though long known to physicists, the phenomena Of retrograde condensation became known to the oil and gas industry Only in recent years, when deeper drilling disclosed that the behavior of vapors under changing pressures was different in high-pressure reservoirs than under the low-pressure operations with which the industry was familiar. These deep, high-pressure reservoirs in which condensation and vaporization behaved inversely to the accustomed manner became known as "gas-distillate," or preferably "gas-condensate" fields. Partly to prevent precipitation and retention of liquids in the reservoir, but still more to prevent the waste of residue gas, the operation known as "recycling," or preferably "cycling," was instituted, in which the residue gas is reinjected into the reservoir, thus maintaining pressure and driving the wet gas to the producing wells. For lack of field experience to serve as a guide, the industry had to assume that theory and laboratory experiments could accurately forecast retrograde behaviors in operating these gas-condensate fields, but it is obvious that these assumptions should be checked at the first opportunities against actual field experience. To make such checks, it is necessary to accumulate a large quantity of reliable field data, but experience has shown that it is difficult to obtain reliable field data and that the laboratory data as usually presented are not in directly comparable form. The problems of correlation involve the complex phase behavior on the one hand, and a knowledge of field data and a visualization of underground conditions on the other hand. This paper is an approach from field experience, The purposes of this article are to discuss the sources of uncertainty in the data and to present methods of analyzing, interpreting and correlating laboratory and field data. Data mostly from lower Gulf Coast fields are presented, from which some conclusions can be derived, but better data from more sources than those available to the writer will be required before satisfactory answers to many questions can be obtained. This paper is presented to stimulate the analysis and publication of data from other fields, the reexamination of field and laboratory methods, and the taking of more complete and reliable field tests. For these purposes, the writer presents some speculations that otherwise would not be appropriate.

Jan 1, 1947

By Nicholas Kowall, K. L. Clark

Maximum furnace efficiency and close control of final steel composition demand that the steel melter be able to follow closely the variations in the carbon content of the bath. For many years, the fracture test has been used by melters for estimating carbon, because it requires only a very short time to pour a sample into a chill mold, cool it in water, break it with a sledge hammer, and observe the fracture. After long experience gained from the observation of such fractures, most melters are able to estimate the carbon content of steel with amazing accuracy, particularly in the lower carbon ranges. Notwithstanding the utility of the fracture test, there has been widespread interest in other methods for rapid carbon determination to supplement it and to ensure against possible errors in human judgment. Several methods, based upon measurement of magnetic properties as functions of carbon content, have been described in the literature1-6 and have been found to give reasonably reliable results in plant practice when scrap composition is known and controlled. A difficulty encountered in the use of analyzers of the magnetic type is that alloying elements do change the relationship between carbon content and magnetic properties and it becomes necessary to establish calibration curves for all the expected combinations of alloy residuals that are not oxidized in the bath. The work reported here is of an investigation of a method that is independent of alloying elements normally present in constructional steels, being based upon the relatively well-known fact that in plain carbon and low-alloy steels martensitic hardness is a function of carbon content alone. Work oF Other Investigators In I938, Burns, Moore and Archer published & curve? that showed that the hardness of martensite is a function of carbon from 0.10 to 0.50 per cent and is independent of grain size or alloy content, at least within the rallge found in construc-tional S.A.E. compositions. Some of the deeper hardening types investigated, however, contained carbon to a maximum of only o.2o per cent. Using this principle, Kern8 developed a method of rapid carbon determination for S.A.E 43xx steels, His procedure consisted of chill-casting a test bar that was large enough to give a a that could be prepared for Brinell indentations. The test piece was quenched immediately after solidi fication was complete and hardness readings were taken, so that the carbon content could he read from an experimentally determined curve giving the relationship between as-quenched hardness and carbon. Experimental Work Although Kern's work had been done with a relatively deep-hardening steel, it

Jan 1, 1944

By K. L. Clark, Nicholas Kowall

Maximum furnace efficiency and close control of final steel composition demand that the steel melter be able to follow closely the variations in the carbon content of the bath. For many years, the fracture test has been used by melters for estimating carbon, because it requires only a very short time to pour a sample into a chill mold, cool it in water, break it with a sledge hammer, and observe the fracture. After long experience gained from the observation of such fractures, most melters are able to estimate the carbon content of steel with amazing accuracy, particularly in the lower carbon ranges. Notwithstanding the utility of the fracture test, there has been widespread interest in other methods for rapid carbon determination to supplement it and to ensure against possible errors in human judgment. Several methods, based upon measurement of magnetic properties as functions of carbon content, have been described in the literature1-6 and have been found to give reasonably reliable results in plant practice when scrap composition is known and controlled. A difficulty encountered in the use of analyzers of the magnetic type is that alloying elements do change the relationship between carbon content and magnetic properties and it becomes necessary to establish calibration curves for all the expected combinations of alloy residuals that are not oxidized in the bath. The work reported here is of an investigation of a method that is independent of alloying elements normally present in constructional steels, being based upon the relatively well-known fact that in plain carbon and low-alloy steels martensitic hardness is a function of carbon content alone. Work oF Other Investigators In I938, Burns, Moore and Archer published & curve? that showed that the hardness of martensite is a function of carbon from 0.10 to 0.50 per cent and is independent of grain size or alloy content, at least within the rallge found in construc-tional S.A.E. compositions. Some of the deeper hardening types investigated, however, contained carbon to a maximum of only o.2o per cent. Using this principle, Kern8 developed a method of rapid carbon determination for S.A.E 43xx steels, His procedure consisted of chill-casting a test bar that was large enough to give a a that could be prepared for Brinell indentations. The test piece was quenched immediately after solidi fication was complete and hardness readings were taken, so that the carbon content could he read from an experimentally determined curve giving the relationship between as-quenched hardness and carbon. Experimental Work Although Kern's work had been done with a relatively deep-hardening steel, it

Jan 1, 1944

By Frank J. Tolonen, Nicholas H. Manderfield, Paul Jasberg

EARLY in the study of the low grade iron formations of Michigan, wide variations in their structure and texture became evident. Because of these variations no simple method of concentration is possible, and those portions of the formations that can be exploited profitably under a given stage of metallurgical progress and existing economic conditions must be searched for carefully. Both structure and texture of the formations have an important bearing on their amenability to bene-ficiation. By structure is meant the banding planes of easy fracture, the porosity, and the degree of leaching. Texture, which includes grain sizes, shapes, and degree of interlocking, determines the amount of grinding necessary to liberate the mineral grains. Structure determines the liberation of portions richer in one mineral. Structure and texture may be termed the gross features of the formation. Earliest surveys of the formations were conducted to outline the parts that could be concentrated at % in. (3 mesh). Operators agreed on this size because anything finer required sintering or other agglomeration processes. At 3 mesh only the structural features, as defined above, would be liberated. With suitable ores concentration was easy, as any of the gravity methods could be used. Sink-and-float gave good results, but with this method only limited portions of the iron formations yielded a desilrable product.1,2 n general, the iroa content could be raised to shipping grade, but the silica content remained too high—sometimes 20 pct—instead of 9 or 10 pct. Grinding did not greatly increase the liberation ofsilica until 2010 mesh or finer was reached. To find the reason fpr this T. M. Broderick began micros~opic examin'ations of the formations in 1933.3 Procedure: The purpose of this discussion is to correlate the appearance of typical portions of the iron formations with their amenability to concentration. As liberation is essential before separation becomes possible, much of the work is based on measuring the liberation achieved by crushing and grinding. Both heavy media and magnetic tube tests were used in this work. On the basis of general structural features such as banding, degree of alteration, and leaching, a specimen was selected from each part of the iron formations studied. The specimen represents the gross features of the formation and not necessarily the particular formation quantitatively. One half of the specimen was polished for macro-study, and the remainder was used for analyses to obtain the grades represented by variations appearing in the macrosection. Specimens for microscopic examination were also prepared for each variation in gross appearance. For correlation of microstructure with liberation, the previous work by sink-and-float methods was supplemented by magnetizing roasting followed by magnetic separation. The results show the liberation of silica to be very important at the sizes used, because any silica particle with iron minerals occluded would be held in the concentrate. A magnetizing roast changes the crushing and grinding character of the sample. For partly leached soft samples the change is slight, but with harder types and those in which there is a considerable change in crystal structure of the minerals, the increase in liberation of the iron minerals may be 30 pct more than that of unroasted samples at the same crusheH size. Gogebic Range Iron Formations: The Gogebic Iron Range is located in the extreme western and southern parts of Michigan's Upper Peninsula, extending westward into Wisconsin. Samples for this study were obtained from the Ironwood formation, comprising three chief members—the Plymouth, Norrie, and Ahvil—with several intermediate slates and thick overlying slates. (The slates are not considered in this discussion because grinding finer than present practice is usually required to liberate the iron minerals.) The predominant iron mineral is hematite, about half of which is hydrated to goe-thite. Limonite occurs in some of the partly leached areas, and siderite in parts of the formation.

Jan 1, 1958