Search Documents

By J. E. Ostberg, G. Phragmen, A. Hultgren, S. Wohlfahrt

Detailed study was made of a number of rimming ingots, both low and high carbon, and especially upon effects of superimposed air pressure. Requirement to suppress core bubbles is between 10 and 15 atm; at 6.5 atm freezing was in semikilled manner and at 3 atm, steel was of rising type. Probable mechanism of freezing under various conditions is discussed. AN earlier paper' reported an investigation made by a committee for studying rimming steel ingots appointed by Jernkontorets in Stockholm. The present paper is the outcome of some further work done by the same committee. Since the characteristics of ordinary rimming steel are connected closely .with the amount of gas liberated during freezing and since this amount of gas is governed by the pressure, it was considered of interest to ascertain in what manner and to what extent definite pressures applied to the top of the liquid steel in the mold would affect the solidification process and the consequent structure of a rimming steel of ordinary composition. The experiments were made at the Domnarfvets Steel Works. The steel was made according to normal practice in a 4-ton Rennerfelt electric furnace. Ferromanganese was added in the furnace; no aluminum was added, with one exception. Analyses of the four heats are given in Table I. The top-poured ingots measured about 12 in. sq x 48 in. and weighed about 1300 lb. One or two ingots of each heat were allowed to solidify under pressure, using a special device for admitting compressed air to the upper closed part of the mold, as shown in Fig. 1. A heavy plate sealed with asbestos was bolted to the top of the mold. The plate had a tapered aperture for pouring. Immediately after pouring the hole was closed by a wedged plug, and compressed air was admitted through a hole in the plug. Because of some delay in applying the plug, full pressure was not reached immediately. The pressure was adjusted to the desired value as indicated by a manometer. In order that the interior of the ingot might have the benefit of the pressure, the freezing of the top crust was delayed by a refractory lining applied to the top part of the mold, Fig. 1. Ingots were also cast from each heat without applied pressure, and with and without refractory lining at the top. Axial sections of ingots were cut either of the whole ingot or of some part of it of special interest; sections were polished and usually etched.' To facilitate description of structures the following terms may be used for different types of ingots solidified under gas evolution: 1. Box-hat or boot-leg ingot: Abundant gas evolution during casting and during rimming; no rim holes. 2. Normal rimming ingot: Lively gas evolution during rimming; usually rim holes in lowest part of

Jan 1, 1952

By R. J. Walter, W. T. Chandler

The Ch-H phase diagram was determined for by-drogen concentrations up to ChHo.9 at temperatures below 400°P'. The phase diagram includes a mis-cibility gap and a eutectoid transformation. A peri-tectoid transformation is postulated at the hydrogen-rich end of the diagram, Phase diagrams were determined for two levels oj purity, of the columbium. A single solid solution exists in the Cb-H system above 400°F. There has been considcrable disagreement among investigators concerning the system at temperatures below 400°F. Albrecht, Goode, and ~allett' proposed a miscibility gap containing two bcc phases with the two lattice parameters converging at about 140°C (285-F), and Brauer and ~erman' found a two-phase room-temperature region between 10 and 41 at. pct H. At sufficiently high hydrogen concentrations in the one-phase region, the hydrogen-rich phase was found to be face-centered orthorhombic. Wainwright, Cook, and Hopkills3 recently reported that the face centered orthorhombic hydride phase is derived from a unit cell which is slightly tetragonal with a small departure from 90 deg of the angle (y) opposite the r axis. The orthorhombic hydride phase was observed for hydrogen concentrations between 0.2 and 0.8 H/Cb atom ratio. Paxton and coworkers4 found that needlelike hydride plates formed in a hydrogen-charged columbium single crystal and suggested that this transformation possessed the characteristics of a diffusionless phase transformation. On the basis of room-temperature, X-ray diffraction data, komjathy' suggested that an order-disorder or martensitic transformation occurs. In the present study, the Cb-H system was investigated to resolve the discrepancies found in the literature for this system. PROCEDURE The columbium specimens were prepared from two heats of wrought 1/2-in.-diameter electron-beam melted columbium rod and from two columbium powders of -80 mesh size of different impurity contents. The columbium bar stock was pur chased from Urah Chmg Corp.; the 99 and 99.5 pct purity colulnbium powders were obtained from Fansteel Metallurgical Corp. and Kern Chemical Co.. respectively. The chemical analyses of the columbium bar and powders are listed in Table I. Hydrogen charging was performed by exposing the columbium specimens to hydrogen at 1 atm pressure at various temperatures. After exposure the specimens were quenched to prevent the hydrogen pickup which would take place if cooled in hydrogen, or the hydrogen loss that would occur if cooled in an inert gas. Adequate hydrogen purity was achieved by passing high-purity tank hydrogen (maximum 5 ppm total impurities) through an Engelhard catalytic Deoxo unit, magnesium per chlorate desiccant, and finally through activated charcoal at the temperature of boiling nitrogen. Activated charcoal at -321°F has been reported6 to remove impurities from hydrogen to a nondetectable level. A schematic representation of the heat-treating apparatus is shown in Fig. 1. A metal-sheathed thermocouple embedded in the colun~bium specimen was used to control the temperature during heat treatment and to pull the specimen boat into

Jan 1, 1965

By ALEX. S. THOMAS

HOWEVER good a furnace may be in regard to design, etc., or however excellent in the quality of the gas used, a suitable heat for the successful working of the metal cannot be obtained unless the melt be coated with a proper quantity of slag. This coating may be excessive or it may be deficient in quantity. The right degree of heat is the essential condition of successful working, for the quality of the steel made is never very good when the metal is allowed to simmer in the furnace for an excessive period, and this heat cannot be obtained if the metal is not protected by a proper covering of slag. This is not only to prevent the metal being over-oxidized and wasted, but also to prevent the metal being chilled when exposed with only a thin covering of slag. The slag may be obtained in either of two ways : 1, naturally, by the presence of sufficient silicon in the iron used, to unite with iron oxide to form a staple slag ; or, 2, by the addition of slag or free silica. In the first case the slag is formed naturally by the action of the oxygen in the flame - i.e., the oxidizing atmosphere of the furnace-on the silicon in the metal when melting. The charge then melts, as it is termed, "thick," and protects the banks from being cut. If too much silicon be present, however, and an excessive quantity of slag be formed, it will be found to be rather infusible, and unless care be taken to add the oxides quickly and follow the furnace up-thus rendering the slag more fusible by the extra iron oxide-the furnace bottom is liable to be pulled up. In such cases the author has frequently been able to warn

Nov 1, 1906

By C. W. Crispell

THE four nomograms presented in this article were designed to simplify and make more, rapid the calculations connected with the compression and transmission of air. The formulae involved are rather complicated, but the graphic solutions are simple; their use requires an ability to follow explicit directions and to interpolate values on a logarithmic scale. ? For the sake of convenience, the nomograms will be divided into two classes, and the purpose and accuracy of each will be discussed. Compression It is frequently desirable to determine the horsepower necessary to compress a given amount of free air from atmospheric pressure to a certain final pressure. The nomograms in Figs. 1 and 2 present a rapid method of calculating the horsepower required to compress 1 cu. ft. of free air per minute by single or two-stage compression. The general formula for the horsepower required to compress air adiabatically is: HP = S X 144/33,000 PVn/(n-1) [(P'/P) n-1/Sn -1] (1) where: P = absolute atmospheric pressure at compressor, in pounds per square inch. P' = final absolute pressure of compressed air, in pounds per square inch. V = volume of free air compressed per minute, in cubic feet. S = number of stages. n = exponent of the compression curve.

Jan 6, 1917

By C. L. Meyers, J. L. Lytton, T. E. Tietz

The recovery of tensile flow stress of 99.995-pct Al and Al-1 pct Mg alloy was investigated using a fractional recovery parameter. Tensile strainirg was conducted at room temperature, and recovery treatments were made in the range from 80° to 200°C. Equal values of fractional flow stress recovery were found to result in equivalent structural states. Identical recovery treatments were found to produce constant values of fractional flow stress re covery, independent of prestrain. The activation energy for recovery of the 99.995-pct A1 between 80" and 200°C was found to be 23,000 +2000 cal per mole, and the activation energy for the Al-1 pct Mg alloy was 27,500 cal per mole. 1 HE degree of recovery of a cold-worked metal may be studied by measuring the changes which take place in any of a number of properties. Some of the properties which have been used by past investigators include X-ray diffraction phenomena, electrical resistivity, hardness, creep strength, elastic limit, and flow stress. Despite the apparent preponderance of such studies, little is known concerning the effect of recovery on the strength of metals except as deduced from changes in various types of hardness measurements. Furthermore, little information is avail- able concerning the effects which specific solute atoms have on the recovery process. Limited studies have indicated that in some cases solid-solution additions greatly decrease the rate of recovery,' whereas in at least the case of magnesium additions to alluminum an increase in the rate has been reported.2 The purpose of this investigation was to determine the effect of a 1 pct Mg addition on the recovery of high-purity aluminum. Because of the particular interest in the effect of solute additions on the recovery behavior as related to mechanical properties, the degree of recovery was evaluated in terms of tensile flow stress. For the purposes of this study, a recovery process shall be defined as any process, short of recrystallization, whereby the properties, of work-hardened metals tend toward their values ill the unstrained state. EXPERIMENTAL PROCEDURE Test Materials. The materials used in this study were a 99.995-3 A1 and an Al-1 pct Mg alloy made from high-purity base metal. The high-purity aluminum contained the following wt pct impurities: 0.001 pct Cu, 0.002 pct Fe, 0.001 pct Si, and 0.0004 pct Mg. The Pil-1 pct Mg alloy contained 0.001 pct Cu, 0.002 pct Fe, 0.003 pct Si, and 0.99 pct Mg. Both materials were obtained in the form of as-rolled 0.125-in.-thick sheets, from the Alcoa Research Laboratories, New Kensington, Penn. Tensile specimens were cut from these sheets with the longitudinal axis in the rolling direction. Both materials were recrystallized in a molten salt bath; the high-purity aluminum at 450° C for 20 min and

Jan 1, 1962

The following petition for amendment of the constitutional provisions relating to qualifications for membership in the Institute, signed by 75 members, of whom 27 are members of the Committee on Increase of Membership, was received by the Board of Directors, was printed on the program of the New York Meeting sent to all members early in January, and is now being voted upon by the membership: In accordance with the terms f Article X, we hereby propose the following amendment to the Constitution, Article II, Section 2: Members shall comprise all those persons who on the third Monday of February, 1918, were members of the Institute, and in addition thereto, all those thereafter, elected or transferred into the, class of Members. A person to he eligible for election or transfer into the class of Members must he at least 27 years of age and must have had at least six years' employment in the practice of engineering, mining, geology, metallurgy or chemistry, during at least three years of which he must have held positions of responsibility in one or more of these fields. Graduation from the scientific course of a college, approved by the Committee on Membership, shall be considered equivalent to two years' employment, as required in the previous sentence.

Jan 2, 1918

1. What Is a Rock Burst? . . . . 569 Jack Spalding . . 569 A. F. Robertson . 569 W. R. Crane . 569 G. S. Rice......569 P. J. Shenon........... 569 L. C. Graton........... 569 2. What Are the Causes of Rock Bursts? 573 Jack Spalding..........573 A. B. Yates and P. J. Shenon 574, 578, 592, 596 A. F. Robertson . . . . . 575, 595 W. R. Crane. ... 579 G. S. Rice.........582 Oscar Weiss .........582 P. B. Bucky..........582 P. H. Bird.....588, 592, 593, 595 M. K. Hubbert.........593 G. Wheeler.......... .593 B. F. Tillson........593, 595 T. T. Read............594 3. How Can Rock Bursts Be Prevented?. 597 Jack Spalding..........597 A. B. Yates and P. J. Shenon ... 598 A. F. Robertson.......599 W. R. Crane....... .602 G. S. Rice............602 Page 4. How Can Rock Bursts Be Predicted?. 602 Jack Spalding.........602 A. F. Robertson.......602, 603 A. B. Yates and P. J. Shenon ... 602 W. R. Crane......602 G. S. Rice......602 B. F. Tillson...........603 5. How Can Rock Bursts Be Controlled? 603 Jack Spalding..........603 A. F. Robertson.......603 W. R. Crane...........604 A. B. Yates and P. J. Shenon 604 Oscar Weiss........605 G. S. Rice......- 604, 609 R.D.Hoffman..609, 610 R. D. Hall..........609 R. H. Cromwell . . 609 P. J. Shenon...........609 P. B. Bucky......609, 611 B. F. Tillson.........609, 611 A. B. Yates...610, 611 P. H. Bird.......610 6. General Discussion........ 611 Jack Spalding.......... 611 R. D. Parker....... . 616 C. Baring Horwood........ 618 P. B. Bucky........... 619 Foreword This symposium brings together points of view, experiences and ideas on rock bursts from a goodly portion of the globe. Some conceptions, particularly those regarding the necessity of depth, have been fairly well shattered, as we find that they are present in the water tunnels of New York, on the surface at marble quarries in Vermont, and in the coal mines of the United States, as well as in the deep mines of the South African and Kolar gold fields, and in the nickel, copper and gold mines of Canada. Their occurrence under such a variety of conditions is, therefore, a challenge, which, if successfully met and overcome,

Jan 1, 1946

By R. E. Hobart

The development of the Hauto power plant and the claims made by various engineers that electricity was more economical than steam for power purposes in and about the mines, led the Lehigh Coal and Navigation Co., in 1911, to conduct a test to ascertain the consumption of power used by a large steam hoisting engine. The question being one on which no reliable information could be found, and the opinion of various engineers differing to such an extent, it was decided that a test under actual operating conditions was necessary. This was arranged for at one of the collieries. The engine selected was 2 30 by 60-in. (76.2 by 152.4-cm.) piston-valve engine of modern type, and comparatively new. The boiler plant from which the hoist received its power was about 600 ft. (182 m.) from the engine, the latter being fed by a 10-in. (25.4-cm.) steam line insulated with magnesia pipe covering. Two batteries of the boiler plant, aggregating 1200 hp., were cut off and fed into a separate steam line leading direct to the hoist engine. Steam auxiliaries, consisting of feed-water pump and blowers, were fed by the boilers in test, and their consumption charged against the hoist. A barrel weighing device was installed, as it was felt that this would be the most accurate way of determining the consumption of water. The fuel, No. 3 buckwheat, was carefully weighed, and every precaution was taken to make the test accurate in every particular. The test was run for 1 week, or a total of 168 hr. A record was kept of the number of trips hoisted or lowered, and continuous indicator cards were taken. One particular set of cards was taken with the hoist operating balanced, and also with the hoist operating with no counterweight other than the empty cage, the coal in the car being weighed. The speed of the hoist was taken by means of a graphic recording instrument which registered the number of revolutions every 5 sec. From this record, speed-time curves were plotted.

Jan 1, 1918

By M. L. Requa

This paper is abstracted from the report of the Appraisement Committee of the Independent Oil Producers' Agency, of which the writer was Chairman. The other members of the committee were M. V. McQuigg and R. S. Haseltine. To Thomas Cox, engineer in charge of the investigation, and to his efficient staff of assistants, is due the credit for the detail work necessary in carrying out the plan of the Committee. It treats only of the valuation of the lands, wells, and piping, without going into details of equipment and other features. It was recognized, early in the operation, that the value of oil lands was the value of oil ,to be extracted and marketed, less the costs attendant thereon. Referring this back to the costs in cents per barrel, it became obvious that surface improvements, absolutely necessary in the production of oil, from wells then drilled, had no separate and independent value aside from the value of the land, but that any excess equipment, not necessary for the production of oil from present wells, such as drilling tools, well casing, etc., should be given a present condition value. In valuing the properties of the Independent Oil Producers' Agency, the Committee has considered the following facts: 1. That from each property there will ultimately be produced a certain total quantity of oil. 2. That in the production of that oil a certain total quantity of money will be expended. 3. That a certain total amount of money will be received from the oil. 4. That the total net receipts will be the total gross receipts less the cost of development and production. 5. That the present value of the net receipts must be such an amount that when invested by a purchaser it will be returned with 8 per cent, interest additional during the life of the property. The initial procedure consisted in making a general reconnaissance of the entire district in which the property was located and determining the lithological and structural conditions underlying the area. The data obtained from each individual tract comprised the logs of all the wells

Jan 1, 1918

By Carle R. Hayward

LEAD ore smelting plants have been operating in general at reduced capacities and secondary lead has assumed relatively more importance during the last year. Present smelting practice results in a large amount of dross, often over 25 per -cent, from blast-furnace lead. This is usually treated at a fairly high temperature in a reverberatory furnace to remove part of the lead and produce a matte-speiss product which is shipped to a copper plant. Few smelters are satisfied with this 'treatment. The fume losses are high and the matte-speiss contains considerable lead. It would seem that a fruitful field for research was open here.

Jan 1, 1934

By W. C. Ellis, E. S. Greiner

WHEN metallic materials are deformed plastically, the process may be considered as one in which hardening and recovery occur simultaneously. The net hardening is that produced by deformation in the absence of recovery lessened by recovery during and immediately following deformation. Strain hardening takes place through movements of large groups of atoms acting to a degree as an entity. A complex microstress system is developed. Recovery is a diffusive-type process involving single atoms or, at most, only a few atoms in concerted action. This is accompanied by elastic strain relaxation. Recovery is strongly temperature-dependent. The driving energy for the process resides in thermal fluctuations of the atoms augmented by the energy of the stress field producing the deformation, and by that produced by the deformation. At very low temperatures recovery is essentially absent, or very small. At high temperatures in the hot working range, recovery is so rapid that deformation results in no appreciable net hardening. The interplay of strain-hardening and recovery results in differing end structures depending on the temperature and the strain rate of the process. For example, there is a prominent difference in the spacing of the slip markings and in the detail of X-ray diffraction patterns. High temperatures and slow strain rates favor a wide spacing of slip markings and sharp reflections.',' This suggests that change in rate of the recovery concurrent with deformation modifies to a degree the manner of the deformation. Different slip systems may operate. For very slow rates, the mechanism may, as has been suggested, differ from that of "classical slip." In the experimental work that follows the findings will be interpreted from the point of view developed in this section. Recovery and Electrical Conductivity Electrical conductivity is a sensitive indicator of the state of strain in a material3' * and was used in this investigation. The materials studied in wire form were: OFHC copper, a high purity (99.99 pct) and 2s grade aluminum, and grade A nickel. Wire annealed and initially 0.050 in. in diam was drawn through diamond dies in a simple holder maintained at 25", —75°, or — 195°C. Precautions were taken that for each material all conditions of drawing were the same except the temperature. Electrical resistivity was measured for each condition at 20°C. This was done as soon as practical after drawing to minimize possible room temperature recovery. The data for the four materials are plotted in Fig. 1 in terms of the change in resistivity for drawing at the several temperatures. The effect of temperature of drawing on the increase in resistivity is most pronounced for copper. Drawing at 25°C to 80 pct reduction in area increases the resistivity approximately 2 pct; drawing at —195°C to the same reduction increases the resistivity about 6 pct. The increase in resistivity" & in this metal is due to extra scattering of conduction electrons originating in the lack of orderly arrangement of the atoms induced by the deformation process. It has been suggested

Jan 1, 1953

By R. E. Hobart

THE development of the Hauto power plant and the claims made by various engineers that electricity was more economical than steam for power purposes in and about the mines; led the Lehigh Coal and Navigation Co., in 1911, to conduct a test to ascertain the consumption of power used by a large steam hoisting engine. The question being one on which no reliable information could be found, and the opinion of various engineers differing to such an extent, it was decided that a test under actual operating conditions was necessary. This was arranged for at one of the collieries. The engine selected was a 30 by 60-in. (76.2 by 152.4-cm.) piston-valve engine of modern type, and comparatively new. The boiler plant from which the hoist received its power was about 600 ft. (182 m.) from the engine, the latter being fed by a 10-in. (25.4-cm.) steam line insulated with magnesia pipe covering. Two batteries of the boiler plant, aggregating 1200 hp., were cut off and fed into a separate steam line leading direct to the hoist engine. Steam auxiliaries, consisting of feed-water pump and blowers, were fed by the boilers in test, and their consumption charged against the hoist. A barrel weighing device was installed, as it was felt that this would be the most accurate way of determining the consumption of water. The fuel, No. 3 buckwheat, was carefully weighed, and every precaution was taken to make the test accurate in every particular. The test was run for 1 week, or a total of 168 hr. A record was kept of the number of trips hoisted or lowered, and continuous indicator cards were taken. One particular set of cards was taken with the hoist operating balanced, and also with the hoist operating with no counterweight other than the empty cage, the coal in the car being weighed. The speed of the hoist was taken by means, of a graphic recording instrument which registered the number of revolutions every 5 sec. From this record, speed-time curves were plotted.

Jan 2, 1918

By R. O. Harma

Introduction Wet autogenous grinding is utilized in three iron ore concentrating plants operated by the Cleveland-Cliffs Iron Company (CCI). This paper will trace some of the development in converting from the use of metal grinding mill liners to the use of rubber and will update the current performance of rubber liners in these applications. The Cleveland-Cliffs Iron Company is a natural resources firm with major interests in iron ore mining and processing and oil and gas contract drilling. The company also has interests in oil shale, uranium, forest products, and Great Lakes shipping. The three operations discussed in this paper are the Empire and Tilden Mines on the Marquette Iron Range in Michigan's Upper Peninsula and the Sherman Mine in northern Ontario, Canada. The Empire Iron Mining Partnership is managed by The Cleveland-Cliffs Iron Company and is owned by Inland Steel, McLouth Steel, The Cleveland-Cliffs Iron Company, and International Harvester. The Tilden Iron Mining Partnership is also managed by The Cleveland-Cliffs Iron Company and is owned by Algoma Steel Corporation, Ltd., Jones & Laughlin Steel Corporation, The Cleveland-Cliffs Iron Company, Steel Company of Canada, Wheeling-Pittsburgh, and Sharon Steel Corporation. The Sherman Mine is a joint venture managed by Cliffs of Canada, Ltd. and owned by Dominion Foundries and Steel Company, Ltd. and Tetapaga Mining Company, a wholly owned subsidiary of The Cleveland-Cliffs Iron Company. The concentrators at all three mines utilize two stage autogenous grinding. Empire and Sherman process magnetic iron ores (Table 1) and utilize magnetic, hydraulic, and flotation concentration methods. Tilden processes an oxidized iron ore (martite, goethite, and hematite) and utilizes a selective-flocculation desliming and flotation concentration flowsheet. Final grind particle sizes are 90% -325M (43k) at Sherman, 90% -500M (25,u ) at Empire and 85% -500M (25 µ) at Tilden. Developmental History The success of using rubber mill linings in Scandinavia led to the first rubber mill lining used by CCI. It was installed in a conventional primary ball mill at Republic Mine in 1964 as reported by Lindroos (1970). This was followed by additional rubber liners for both primary and regrind ball mills. Generally these rubber linings provided about twice the service life as compared to the Type I Ni-hard liners previously used. Grinding efficiency of rubber was found to

Jan 1, 1982

By R. E. Cech

Particles -3 to 30 µ diam of a 29.5 pet Ni, 70.5 pet Fe alloy after being melted and solidified while falling through a hydrogen atmosphere were found to contain a distortion-free body-centered-cubic phase. In most particles, the amount of body-centered-cubic phase approaches or equals 100 pet. It was shown by a series of experiments that this phase forms directly from the liquid. It is pointed out that a mechanism previously suggested in recent papers on the theory of the liquid-solid transformation can account for the solidification of body-centered-cubic phase in a temperature range where face-centered-cubic is the stable phase. IN the course of an operation to produce powders for a study of the martensitic transformation in Fe-Ni alloys, an unexpected phenomenon was observed. Powders of a 29.5 pet Ni alloy, which has a subzero M, temperature, were found to contain considerable amounts of a body-centered-cubic phase at room temperature. The experiments to be described were designed to elucidate the mode of formation of this unexpected phase. Experiments and Discussion An alloy containing 29.5 wt pet Ni, balance iron, was vacuum melted from high purity electrolytic iron and carbonyl nickel shot and solidified in the crucible. The metal was converted to oxide, ground to 100 pet <37µ, pressed to a cake, and homogenized 20 hr at 1350°C. To insure homogeneity the grinding, pressing, and homogenizing heat treatment was repeated a second time. The oxide was then ground to 100 pct <37µ and hydrogen reduced at 500°C. The reduced powder was given a spheroidizing treatment to produce spherical cast particles. The treatment consisted of dispersing the particles in hydrogen and allowing them to drop through a vertical hydrogen furnace set to a temperature higher than the liquidus of the alloy. This operation, commonly known as shotting, has been described more fully elsewhere.&apos; The powder produced by this method was found to contain approximately equal parts of body-centered-cubic and face-centered-cubic phases. A magnetic separation technique, previously described,&apos; was applied, and it was found that particles were either completely face-centered-cubic or nearly completely body-centered-cubic. The microstruc-

Jan 1, 1957

By Perry Harrison

THE increased use of sintering for the beneficiation of iron ores and the reclaiming of flue dust creates a lively interest in sintering costs and, economics. The character of material sintered and geographical location of plants so radically alter sintering costs and economics that it is well to understand at least the basic elements which control such changes. The following cost factors are believed to be roughly approximated for large-scale Dwight-Lloyd &apos;continuously operated sinter-machine installations located anywhere. PER CRUDE TON Labor, supplies and repairs 0.15 Power 6.5¢ X kw-hr. rate ? Plant overhead and administration 0.05 Depreciation per ton annual capacity 0.05 Fuel: 6 per cent coke breeze or equivalent minimum ? 1 per cent coke breeze additional for each 5 per cent free and combined water in ore or dust ? Ignition distillate at 0.6 gal. per ton ? PER SINTER TON Royalty on Ore 0.10 Royalty on Flue Dust 0.15 PER CRUDE TON "Winter expense"; i. z., the cost of the five months enforced idle . period for plants tied in to Great Lakes transportation season 0.03 Using the foregoing data, it is possible to roughly approximate the cost of efficient sintering at any location for. any ore, viz:

Jan 1, 1932

THE morning session on mining methods with R. M. Raymond as chairman was devoted mainly to papers on explosives and the discussion of these papers. A paper on the numerical index of the re-sistance which rocks offer to the penetration of a drill bit was also read. The first paper, "Relation Between the Oxygen Bal-ance and Propulsive Strength of Eight Gelatin Dynamites" by G. St. J. Perrott, N. A. Tolch and J. E. Crawshaw, was presented by Mr. Perrott, super-intendent of the Pittsburgh Experiment Station of the U. S. Bureau of Mines. In this paper which is the beginning of a series of publications on explosives, Mr. Perrott stated that the attempt was made to put down in quantitative form the facts which have been known to explosive engineers for a long time. Eight samples of 40 per cent gelatin dynamite, with oxygen content varying from + 15 to - 36 per cent of the theoretical amount necessary to form complete combustion with all of the combustible elements were tested. The experimental work showed that a bal-anced explosive did not give the greatest propulsive strength-but the most favorable range was from - 8 to - 25 per cent oxygen. The experimental work also brought out the fact that the wrapper of a stick of dynamite enters quite completely into the explosive reaction, and gelatin dynamites from which the wrapper had been removed developed less strength than the a same explosive with the wrapper. The second paper, "Effect of Oxygen Balance of Gelatin Dynamites on the Gaseous Products of Det-onation," by G. W. James and G. St. J. Perrott, was also presented :by Mr. Perrott. The first portion of this paper is given over to a discussion of the relative merits of different types of apparatus for testing and analyzing the combustion products of dynamites. Three types were used (1) the Bichel gage, (2) the Crawshaw-Jones apparatus and (3) the Hercules tank. All three of these types were used in testing dynamites whose oxygen balance varied from-35 to + 6 per cent.

Jan 3, 1928

PRESIDENTS DAVID THOMAS 1871 R W RAYMOND 1872-1874 A L HOLLEY1875 ABRAM S HEWITT 1876 T STERRY HUNT 1877 ECKLEY B COXE 1878 - 1879 WILLIAM P SHINN 1880 WILLIAM METCALF 1881 RICHARD P ROTHWELL 1882 ROBERY W HUNT 1883 JAMES C, BAYLES 1884-1885 ROBERT H RICHARDS 1886 THOMAS EGLESTON 1887 WILLIAM B POTTER 1888 RICHARD PEARCE 1889 ADAM S HEWITT 1890 JOHN BIRKINBINE 1891-1892 H M HOWE 1893 JOHN FRITZ 1894

Jan 1, 1923

PRESIDENT AND DIRECTOR EUGENE MCAULIFFE OMAHA, NEBR. PAST PRESIDENTS AND DIRECTORS HERBERT G. MOULTON NEW YORK, N. Y. JOHN R. SUMAN HOUSTON, TEXAS TREASURER AND DIRECTOR H. T. HAMILTON NEW YORK, N. Y. VICE PRESIDENTS AND DIRECTORS ERLE V. DAVELER NEW YORK, N. Y. W. M. PEIRCE PALMERTON, PA. PAUL D. MERICA NEW YORK. N. Y. LEROY SALSICH DULUTH, MINN. CHESTER A. FULTON NEW YORK, N. Y. L. E. YOUNG PITTSBURGH, PA.

Jan 1, 1942

By W. C. Bednar

In all, 127 producing oil wells, 8 producing gas wells and 212 dry holes were drilled during 1936 in the Central Texas area; 76 wells in Bexar County, 62 in Caldwell County, 44 in Guadalupe County, 22 in Williamson County, 20 in Navarro County and 20 in Frio County. Less than 20 were drilled in each of the other counties and none at all in Ellis, Hill, Bosque, Coryell, Lampasas, Burnet, Llano, Kennedy, Mason, Real, Kinney and Uvalde Counties. The Pearsall-Austin chalk field in Frio County and the Zoboroski field in Guadalupe County were the only new discoveries and there were no important extensions to old fields. In this report Corsicana, Mildred (Elm Ridge), Angus-Edens-Hodge, Burke, and Rice-Oil Ridge, all shallow Navarro County stripper fields, are grouped together under the name of Corsicana. This grouping follows that of the Railroad Commission of Texas, thus facilitating the gathering of production data. A map showing the location of the oil and gas fields in the Central Texas Area was published in Volume 114 of the A.I.M.E. TranBactions, page 380. New Fields Pearsall-Austin Chalk.—The Amerada Petroleum Corporation completed 13 Austin chalk wells during 1936 on the large Amerada-Rycade block in Frio County. Other companies drilled two dry holes to the Austin chalk in this vicinity. Not enough wells were drilled to give control of the structure but it appears to be a nose plunging in a west-southwest direction. A second deep test is being drilled in the Pearsall area and at this writing has cemented off a show of oil and gas in the Edwards limestone. The Humble Oil and Refining Co. is building a 6-in. pipe line from Lytle, Tex., to serve the Pearsall field. Zoboroski.—Actual discovery of the Zoboroski field was made by W. J. Walton et al. in 1931. The discovery well, Anton Zoboroski No. 1, was a small producer making but from 3 to 5 bbl. per day, which was used locally for fuel oil. The discovery of the Darst Creek Extension in

Jan 1, 1937

By Rees D. Rawlings, C. W. A. Newey

The aging characteristics of an Fe-11 at. pct Mo alloy have been studied by means of light metallography together with density, Young&apos;s modulus, and hardness measurements. The results were consistent with the precipitation of a single intermetallic compound during aging; overaging was slow relative to that in other iron-based binary alloys. The solution treatment temperature had a small effect on the rate of hardening whereas deformation prior to aging had a marked effect on both the rate of hardening and the peak hardness. The density data indicate that the compound precipitated is Fe3MO2 and not the Laves phase Fe2Mo. Analysis of the modulus and density results gave values for the time exponent for precipitate growth of approximately 1.0 and 1.5 for the alloy aged with and without prior deformation, respectively. DETAILED studies of precipitation hardening in bcc matrices have been confined largely to the effects of carbides and nitrides. In view of this and the growing technological interest in intermetallic compound strengthening, e.g., in maraging steels, a study of precipitation in iron-based alloys with a low interstitial content has been undertaken. This paper is concerned with the aging behavior of an Fe-11 at. pct Mo alloy; the mechanical behavior of the alloy will be reported later. The early work of sykes on Fe-Mo alloys showed that precipitation of the intermetallic compound was accompanied by an increase in hardness and a decrease in volume of the material. More recent surveys of the strengthening associated with precipitation have been made3-5 and, in particular, Elsen and wassermann4 showed that deformation prior to aging increased the rate of hardening. These latter workers also followed the precipitation process by means of dilatometry, electrical resistivity, and lattice parameter measurements. Their results confirmed that there is a decrease in volume on aging. Except for the work of Hornbogen on an Fe-20 at. pct Mo alloy, neither clustering nor the precipitation of a nonequilibrium phase has been observed in Fe-Mo alloys. Studies of alloys of lower molybdenum content475 indicate that the equilibrium intermetallic compound is precipitated during aging. However, there is some doubt concerning the nature of the equilibrium precipitate phase. According to the phase diagram constructed by Hansen,8 the phase should be precipitated. This phase has a rhombohedra1 crystal structure which is characterized by the formula Fe706,&apos; although the composition of the molybdenum-rich boundary corresponds approximately to Fe3Mo2. The version of the diagram proposed by Sinha, Buckley, and Hume-Rother indicates that the A phase, a Laves phase Fe2Mo, should be precipitated. Their observation of a Laves phase supports the earlier findings of Bechtoldt and Vacher,13 although, in a recent study of the system by means of diffusion couples, Rawlings and Newey did not detect the phase. The work presented here describes the effect of solution-treatment temperature, aging temperature, and prior deformation on the aging characteristics of the alloy as revealed by light metallography together with hardness, density, and Young&apos;s modulus measurements. In addition the density data are used in an attempt to determine the compound precipitated during aging. EXPERIMENTAL PROCEDURE A 29-kg ingot of the alloy was cast at R.A.R.D.E., Fort Halstead, from deoxidized, Japanese electrolytic iron and sintered molybdenum. The ingot was homogenized for 6 hr at 1473°K and then worked, with intermediate anneals, into 6- and 16-mm-diam rods and 6-mm plate. Chemical analysis of the alloy gave, wt pct: Mo, 17.5 (11 at. pct); C, 0.003; Si, 0.002; S, 0.005; P, <0.002; and02, 0.0098. Solution treatments were carried out under a dynamic argon atmosphere in a vertical, "crusilite" element, furnace which had a facility for rapid quenching into iced water. Except for the study of the effect of solution treatment temperature, all specimens were solution-treated at 1573" * 2°K for 1 hr. Salt baths were used for the aging treatments. Specimens for hardness, density, and Young&apos;s modulus measurements were produced, after heat treatment, from the stock rod or bar using a precision silicon carbide slitting wheel. As described later, the quenching treatment produced local plastic strain in the stock material; consequently, care was taken to ensure that the specimens were not prepared from these regions. Those specimens used in the studies of the effects of prior deformation on the aging behavior were strained in compression in a Denison universal testing machine. Specimens for light metallographic observations were mechanically polished on successively finer grades of diamond paste down to and then etched in either alcoholic ferric chloride or in a 2 pct nital solution. Vickers diamond pyramid hardness data were obtained using a 30-kg load. At least five impressions were averaged for each determination. Density measurements were made using a displacement technique in which each specimen was weighed in air and in dibromoethane at 296°K. The specimens were cylindrical and weighed 3 to 4 g; all weighings were made on a balance reading to 1 x 10"5 g. For each specimen the mean value of five weighings was used to calculate the density. The density of the dibromoethane was determined using the displacement procedure and a standard nickel specimen. The error in an absolute density value was estimated to be HI.01 pct. To obtain the density as a function of aging time a single specimen was used and the density meas-

Jan 1, 1969