Search Documents

By T. J. Whalen, S. M. Kaufman

Surface-tension measurements for liquid Fe-C-Co and Fe-C-Ni alloys were performed by the sesszle-drop technique at 1350o and 1425°C. Cobalt was shown to he more effective than nickel in lowering the surface tension of Fe-C alloys A minimum value for surface tension of 1640 dynes per cm was found in the Fe-C-Co system at a concentration of 1.5 pet C and 12pet Co. Analysis of these measurements in terms of adsorption and desorption behavior indicated that cobalt and nickel lower surface tension in Fe-C alloys by replacing carbon at the liquid-vapor interface. Comparison of results to date for Fe-C liquid alloys has shown that most substitutional-type elements having about the same atomic diameter as iron also have relatively the same influence on surface tension when present in dilute amounts. It has been shown previously that surface-adsorption behavior in liquid Fe-C ternary alloys is related to the manner in which the ternary addition affects the activity of carbon in the bulk solution.' Certain ternary additions, such as chromium, tending to decrease carbon activity cause adsorption of carbon and chromium to the liquid-vapor interface. Additions, such as silicon, increase the carbon activity, resulting in a desorption of carbon and an adsorption of silicon. Both cases were shown to cause a decrease in surface tension due to adsorption. It is the object of this paper, as part of the writers' continuing interest in the effect of alloying additions on the surface tension of Fe-C alloys, to present and discuss surface-tension data on solutions in the ternary systems Fe-C-Co and Fe-C-Ni. Available activity measurements for these systems in the solid state indicate a strong increase in carbon activity when either nickel or cobalt is added to Fe-C alloys.2, 3 EXPERIMENTAL PROCEDURE The alloy compositions used are shown in Table I. These alloys were prepared by vacuum melting in stabilized zirconia crucibles and then vacuum casting into cold-steel molds. The nominal analyses for the alloys used in this investigation are given in Table I. Surface tensions and densities were measured by the sessile-drop method4,5 in conjunction with the tables of Bashforth and bdams.' Specimens were prepared by slicing 1/4-in. cubes from the center of the vacuum-cast ingots and grinding the edges of these cubes until their shapes approximated spheres with flat bottoms. Proper handling techniques, including an acetone rinse immediately before use, assured minimum contamination from sources extraneous to the actual melting. For each experimental run a sample was placed on a BeO plaque and positioned and leveled inside a vacuum induction heating apparatus. The sample and plaque arrangement sat inside a molybdenum tube which acted as the susceptor. Diagrams of this apparatus may be found in the literature.= After heating to temperatures just above the liquidus at pressures of the order of 10-4 to 10- 5 mm Hg, photographs of the drop profile were made using its natural thermal radiation as a light source. Some measurements were made with partial pressures (-1 cm Hg) of a mixture of H2 and He gases. The H2-He atmospheres proved to be necessary at higher nickel contents to retard excessive vaporization losses. Chemical analysis for carbon and the ternary addition was performed for each alloy sample after completion of the experimental run.

Jan 1, 1964

By H. F. Mills

THE Iron King mine is 12 miles east of Prescott Arizona, in low foothills of the Agua Fria mining district. It was operated in 1906 and 1907, using gravity methods of concentration, mostly on oxide ores. In 1923 and 1924 shipments of sulphide ores were made to the Humboldt smelter. It remained inactive and stripped until 1936, when it was unwatered and sampled to the 400-ft level, the bottom at that time. In 1937 the Iron King Mining Co. purchased the mine and shipped oxide ores. During 1938 a bulk flotation plant of 140 tons daily capacity was erected. The mill has been enlarged and operations have been continuous since the mill first started. In July 1942, the Shattuck Denn Mining Corporation purchased the physical assets from the Iron King Mining Co., and since that time it has operated as the Iron King Branch of the Shattuck Denn Mining Corporation. Economic metals recovered are gold, zinc, silver, lead, a little copper, and fluxing pyrite. The ore occurs as a series of northward-dipping shoots arranged in echelon pattern, the series extending over a length of 3500 ft. Strike lengths of shoots vary from 60 to 600 ft, and widths from 3 ft to as much as 14 ft. The ore occurs in a sheared zone in pre-Cambrian chloritic schist. This schist belt is about 6 miles wide, and the ore zone is about 4 miles from the pre-Cambrian granites to the west. No intrusive rocks have been found in the mine, nor is there evidence of any on surface that might indicate a genetic connection with the ore occurrence (Fig I). The schists strike N23°E and dip 75° to the northwest, which might indicate an overturned thrusting from the granites. In the upper levels, the echelon pattern in which the ore occurs was quite regular, no disturbance of the enclosing schist, or of any faulting that might contribute to the formation of the ore pattern was noted. There is a possibility that the ore zone may be on the axis of an isoclinal fold. Another interesting feature is the more or less typical zoning of minerals along the strike in each of the ore shoots (Fig 2). The north end of each shoot is enclosed by schist, while the south ends usually extend out at full width beyond the economic mining limits in a pyrite-quartz low-grade material. The plane of demarcation between ore and schist is very sharp, with little or no impregnation of sulphide in the schist, especially on the footwall side. The footwall schists are usually firm and strong, and vary from dioritic phases to fine-grained, lighter colored bands, almost silky in texture. The hanging wall for a width of 50 to 8o ft consists of alternating sheetings of chloritic and pyritic schists. The mine is now partly developed to the 92o-ft level, with some diamond drilling from the 1150-ft station of No. 6 shaft. Economically there has been little change in nature or grade of ore from the top of the sulphides, about 200 ft below surface, to the bottom levels. There have been a few echelons in depth, just as there are in plan, and while a few shoots have had

Jan 1, 1947

By N. E. Garner

Laboratory experiments were conducted to investigate the cutting of a single diamond on limestone and shale under simulated down-hole conditions. A high-pressure chamber was modified by adding a rock-rotating device so that planing tests could be run. Weight on the diamond, diamond geometry and differential pressure across the face of the rock were varied. It was found that (I) high differential pressure reduced the volume of rock cut by the diamond at a given bit weight by strengthening the rock and changing the mode of failure; (2) a finely powdered rock left in the bottom of the grooves reduced the volume cut by as much as 50 percent; and (3) orientation of a single diamond about the axis of a drill point had considerable influence on diamond cutting efficiency. INTRODUCTION Diamond bits consist of many diamonds held in a matrix provided with water courses for fluid passage to clean, cool and lubricate the diamonds as they drill formation. Each diamond contributes its share to the overall effectiveness of a bit, but a lack of understanding of the performance of a single diamond has hampered efforts to engineer improvements in diamond bits. The need for those improvements prompted this study. This paper describes the findings of a laboratory investigation of the outting action of a single diamond where the differential pressure between the wdlbore and formation, diamond geometry and vertical force on the diamond were independently varied. The tests were conducted in a pressure chamber that provided relative horizontal motion (planing) between a rock and diamond under simulated down-hole pressure conditions. EQUIPMENT HIGH-PRESSURE CHAMBER WITH ROTATING DEVICE The high-pressure chamber used in previous rock mechanics studies' was modified for this study by addition of a rock-rotating device. The modified chamber (Fig. 1) differs from the old chamber in that the rock can be rotated to provide relative horizontal movement between the rock and the penetrator which may be a small element of a diamond or a drag bit. In this study the penetrator was a single diamond. The rock sample holder inside the chamber is mounted on a thrust bearing and is connected to the external drive mechanism by a stem that passes through two seal elements. The seal elements are needed to allow formation pressure to enter the bottom of the rock sample through a small hole in the stem. The Kapseal seal elements (Tefion boots backed by O-rings) provide low friction (hand free) even at differentials of 5,000 psi. The drive mechanism is a variable-speed transmission with a speed range from 0 to 30 rpm and an output torque of 2,800 in.-lb. A right-angle-drive gear box couples the drive to the stem. The new design has two independent pressure systems (formation and borehole) to simulate down-hole rock stress environment. Formation pressure enters from the bottom of the rock through a 6-in. diameter area, and borehole pressure acts over the remaining surface. A 14-in. layer of zero fluid loss oil-base mud poured over the top of the rock and an O-ring seal on bottom allow a differential between the borehole and formation pressures. Bayol 50 was used as the hydraulic fluid in the chamber. The differentials reported here were obtained by elevating the borehole pressure while keeping the formation pressure at zero.

By Ronald C. Whiting

SINCE the advent of what has been aptly called "chemical flotation," about 1920, the number and complexity of the various chemicals used in practice have increased enormously. Over 300 patents have been issued dealing exclusively with flotation reagents, and many of these embrace from two or three up to a score or more of specific compounds. The exact number of compounds actually finding a practical use in flotation would be difficult to determine, though the U. S. Bureau of Mines gives an annual list by groups.

Jan 1, 1938

By S. C. Sun

With the aid of emulsifiers, intense high-frequency sound waves are capable of emulsifying any collector in water. The data show also that ultrasonically emulsified collectors are more effective in floating minerals than the nonemulsified collectors. THE use of ultrasonics in forming emulsions is not new. As early as 1927 Wood and Loomis reported preparation of emulsions with ultrasonics. In 1935 Rschevkin and OstrawskyV escribed the use of great ultrasonic power in producing fine emulsions of various oils and paraffin in water. Recently Oyama and Tanaka3 employed ultra-emulsification to increase the effectiveness of sodium ethyl xanthate in flotation of chalcopyrite and galena. An emulsion is a two-phase system consisting of two incompletely miscible liquids, the one being dispersed as finite droplets In the other. The dispersed liquld is known as the internal or discontinuous phase, and the surrounding liquid is termed the external or continuous phase. There are two types of emulsions; one is oil-in-water (O/W) and the other water-in-oil (W/O). The word oil refers to the liquid other than water. Circumstances exist in which the emulsion type is not clearly defined, and the internal and external phases both contain portions of the opposite phase. This is said to be a dual emulsion. Among the many hypotheses, 5a, B proposed for the formation of emulsions, the Bancroft's adsorbed film or double interfacial tension theory is widely accepted. Bancroft 7, 8 deduced that in the process of emulsification the interfacial tension between oil and water is lowered by the formation of an emulsifying film, which contains the adsorbed molecules and/or ions from the emulsifying agent and the two liquids. This film has two interfacial tensions, one with the water and the other with the oil, which are not necessarily equal. The difference in interfacial tension between the two surfaces of the film is chiefly responsible for forming different types of emulsions. For example, if the interfacial tension between water and film is less than that between oil and film, the film will become convex on the water side, thereby tending to form an oil-in-water emulsion. On the other hand, if the interfacial tension between water and film is greater than that between oil and film, the film will become concave on the water side, thereby tending to make a water-in-oil emulsion. In line with this theory, emulsifying agents soluble in water have the tendency to form oil-in-water emulsions, while those soluble in oil form emulsions of the reverse type. Apparatus and Experimental Procedure: The ultrasonic apparatus shown in Fig. 1 consisted of a hypersonic generator (A), Brush Development Co. model Bu-204; a hypersonic transducer bowl (B) whose resonant frequency is 400 kc per sec; and a round-bottomed glass tube (C) of 2.2 cm ID and 21 cm in length. The acoustical output power of the hypersonic transducer bowl was standardized with a Hewlett Packard vacuum tube voltmeter, model 41 0B, across the hypersonic generator output. The glass tube, containing the materials to be emulsified, was placed 1 cm above the central surface of the transducer bowl, which was filled with water as shown in Fig. 2. Ultrasonic emulsification was performed in three steps, although a one-step method has been used: 1) emulsifying the predetermined amounts of col-

Jan 1, 1956

By J. W. Clark, C. T. Sims

Wrought chromium-base alloys containing yttrium, cubic monocarbides of the Ti(Zr)C type, and similay alloys containing manganese and rhenium have been melted and fabricated. Strength has been studied by hot hardness and elevated-temperature tensile and rupture measurements, low-temperature ductility by tensile testing, and surface stability by oxidation testing. In additiod, studies have been conducted of the carbide stability, and of aging behavior. The carbide dispersion generates effective elevated-temperature strength, which is further enhanced hv strain-induced precipitation. The dispersion exhibits classical dissolution and aging response. The ductile-to-brittle transition temperature of these alloys is above room temperature. The alloys reported show fairly good oxidation resistance, but nitrogen contamination can cause fortnation of a hard Cr2N layer under the oxide scale. Manganese does not appear to be a promising alloying element in chromium. In the years 1945 to 1950, the metal chromium was considered as a possible base for alloy systems due to its considerably higher melting point than superalloys, its low density, its high thermal conductivity, and its apparent capacity for strengthening. However, this interest in chromium was short-lived. It was found difficult to melt and cast, to be exceptionally sensitive to the effect of minor imperfections, to have a lack of ductility at both room and elevated temperatures, and to be subject to a deleterious effect of alloying elements upon the ductile-to-brittle transition temperature.' Since then, chromium, as a practical alloy base, has remained virtually unstudied. Further, purposeful ignoring of chromium has been promoted by statements that its bcc structure would not allow it to be strengthened to useful values, when compared to the "austenitic" alloys.2 Recently, a new look has been taken at chromium-base alloy systems. Study of the literature will show that chromium, providing some of its disadvantages could be eliminated or minimized, actually has a rather attractive potential as an alloy-system base. Analysis of rather scattered data suggests that chromium is quite capable of being strengthened to high levels. Also, significant strengthening of its two sister elements in Group VI-A, molybdenum and tungsten, has been demonstrated in a number of commercial and exploratory alloys. Chromium should be similar. Since chromium does not readily form a volatile oxide like tungsten or molybdenum, it offers a much higher probability of giving birth to alloy systems with useful oxidation resistance. Concerns about possible high elemental vapor pressure have been mitigated by recent data.3 In addition, the physical properties exhibited by chromium are attractive for application as a high-temperature structural material. For instance, its thermal conductivity varies from 49 to 36 Btu-ft/hr-sq ft-°F over its range of usefulness (which is two to four times higher than most superalloys), its density is about 7.2 g per cc (20 pct less than most nickel-base alloys), its coefficient of thermal expansion varies from 4 to 8 x 10-6 per OF, and it has a relatively high modulus of elasticity, approximately 42 x 10' psi.4 Alloying studies on a chromium base in the past have usually encompassed rather sweeping solid-solution alloy additions for strengthening. This is not consistent with contemporary alloying practice in Group VI-A. For instance, molybdenum, also in Group VI-A, is primarily alloyed for strength improvement by use of heat-treatable carbide dispersions.5 Chromium and molybdenum are similar in their chemical activity and other properties. Thus, strengthening of chromium by carbide dispersions was studied. Chromium-base alloys are plagued with room-temperature brittleness, although high-purity unal-loyed chromium can be made ductile.4,8 Use of yttrium as a scavenger has done much to improve ductility and resistance to nitrogen embrittlement in chromium systems,7 so it was utilized in this program. It has also recently been found8 that small rhenium additions (1 to 5 pct) create improvement in the ductility of Type 218 tungsten wire. This is apparently related to the remarkable effect of rhenium additions near its terminal solid solubility in all Group VI-A metals.9'10 Investigation to establish if dilute concentrations of rhenium would also be effective in chromium appeared to be logical for this program. Since rhenium is too expensive to be practical in alloys for application as structural components, ductility improvements through solid-solution alloying were also sought by substitution of manganese for rhenium; manganese, like rhenium, exists in Group VII of the periodic system. The optimum amount of carbide dispersion for chromium-base alloys was obtained by analogy with molybdenum. Strengthening in molybdenum is achieved by use of Ti-Zr carbide dispersions. A

Jan 1, 1964

By Marius S. Darrow, William B. White, Rustum Roy

The PbS-PbTe systen has been studied by quench-ing and D.T.A. techniques f?om 400' to 1150°C. Runs were made in evacuated silica tubes so that all equilibria are at the vapor pressure of the system. Lattice parameters of the quenched salnples , measured by X-ray diffraction, show a complete crystalline-solution series existing over a narrow temperature range between approximately 805" and 871°C. An exsolution dome extends from a maximum of about 805"C (approximately 30 mole pct PbTe) to 1 and 96.5 pet PbTe at 400°C. A narrow melting region, deternined by D.T.A., extends form 918c (mp PbTe), The shapes of the liquides and solidus curves imply the existence of a minimum at 871°C at approximately 65 pct PbTe. THe exact composition of the minimum could not be established due to the very narrow two-phase region. At compositions containing less than 50 pet PbTe, liquidus temperatures begin to increase, while the solidus remains almost flat to about 15 mole pet PbTe before beginning to vise toward the mp of PbS (1075 C). LEAD sulfide and lead telluride are isostructural (NaC1 type) semiconductors whose electrical and optical properties have been extensively studied and used in recent years. If appreciable crystalline solution exists between these compounds, the variation of physical properties with composition could be of interest. The purpose of this investigation was to determine the extent, if any. of crystalline solution, and to obtain the phase diagram for the system. To the knowledge of the authors, only three studies of the system PbS-PbTe have been reported, and, in chronological order, each investigation found an increasing amount of crystalline solution. In 1956, Yamamoto reported finding no evidence of crystalline solution between the compounds. Sindeyeva and Godov-ikov,' in 1959, found very limited crystalline solution. but only under conditions of excess tellurium concentration. Finally Melevski s3 investigation in 1963 indicated that one solid phase exists in the region from PbS to 7 pct PbTe and from 82 pct PbTe to PbTe at 886'C, with an eutectic at 55 pct PbTe at that temperature. Detailed data on the solvus boundary were not given. EXPERIMENTAL EQUIPMENT AND MATERIALS Commercially produced PbTe and PbS powders were used as starting materials. Batches of specific mole percent composition were accurately weighed and mixed in a plastic bottle, in a shaker mill. An analy- sis of impurity content is given in Table I for pure PbS and PbTe and for two randomly selected batches after the powders were mixed. Individual samples, ranging in weight from 0.2 to 0.5 g, were sealed in evacuated silica tubes which had been thoroughly washed and rinsed with acetone and distilled water. Thus all data taken were at the pressure of the system. Subsolidus relations were studied down to 400°C by heating the samples in a vertical tube furnace for 24 hr. The sealed tubes were quenched in water with quench time from the hot zone not exceeding 1 sec. Temperatures were measured by a chromel-alumel thermocouple and controlled to 53°C for most runs. The number and composition of phases present were determined from powder X-ray diffraction patterns taken at room temperature on a Norelco diffractome-ter, using silicon as an external standard. Above 850°C quenching techniques were, in general, found to be unsatisfactory, and differential thermal analysis (D.T.A.) was used to determine melting relations. The evacuated tubes were recessed about 1 cm at one end to accommodate the differential thermocouple. Al203 was used as the reference material in a similar tube containing the other side of the differential couple. For temperature measurements, a separate thermocouple was placed in the recess of the tube containing the sample to be measured, thus providing an opportunity to obtain thermal, as well as differential, analysis. All thermocouples for these measurements were Pt-Pt 10 pct Rh. Temperature and differential curves were recorded separately on synchronized strip-chart recorders. Thermocouples and recording equipment were calibrated using NaCl and gold standards, using the melting points 801" and 1063 C, respectively, which span most of the temperature range of interest. Heating and cooling rates generally were from 4 to 7°C per min. It was found, in fact. that rates ranging from 1.5 to 25°C per min did not significantly change the data obtained.

Jan 1, 1967

By C. H. Li, R. J. Stokes

This paper compares the fracture behavior of tungsten rods in three conditions: recrystallized. recovered, and wrought. Notched specimens suhjected to a 50 in.-lb impact load showed ductile-brittle transitions at 700, 4.90°, and 440°C, respectinely. The recrystallized material had an equiaxed pain structure and jracbred by simple cleavage from a grain boundary source at all temperatures up to 700°C. The wrought and recovered material had an elongated fibrous structure and at low temperatures fractured by cleavage originating from the notch. As the transition temperature was approached cleavage was preceeded by more and more intergvanular splitting which deflected the crack front into planes parallel to the tensile axis. The enhanced toughness of wrought and recovered tungsten was attributed both to its inability to initiate cleavage because no pain boundaries were suitably oriented perpendicular to the tensile stress and to its inability to maintain cleavage because of intergranular splitting ahead of the crack. It has been appreciated for a long time in a qualitative manner that the room-temperature brittleness of fully recrystallized tungsten may be alleviated by working the material at relatively low temperatures.' More recently this difference in mechanical behavior between wrought and recrystallized tungsten has been examined quantitatively by measurement of the tensile properties as a function of temperature. In these experiments brittleness has been expressed in terms of ductility or reduction in cross-sectional area upon tensile fracture or in terms of the bend radius before fracture under bending.' This work has shown the existence of a fairly sharp transition from brittle to ductile behavior with an increase in temperature. The ductile-brittle transition temperature for recrystallized material is approximately 200°C higher than for wrought material. An increase in strain rate, small additions of impurity,' or an increase in grain size4 shift the respective transition temperatures to higher values, but the difference between them remains approximately the same at 200°C. A number of explanations for this embrittlement by recrystallization have been given. It has been blamed either on the concentration of impurity at the grain boundaries, the increase in grain size, or the change in texture which occurs upon recrystallization. The present paper examines the effect of different heat treatments on the notch-impact behavior of commercial powder-metallurgy tungsten rods. The change in the ductile-brittle transition temperature for this method of loading and the fracture mode has been related to the different mi-crostructures produced by heat treatment. EXPERIMENTAL PROCEDURE Commercial swaged powder-metallurgy tungsten rods 1-3/8 in. in length and 1/8 in. in diameter were machined to introduce a sharp V notch 0.030 in. deep. To change the microstructure from that of the as-received wrought material some of the specimens were subjected to an anneal in nitrogen either at 1300° or 1400°C for 8 hr or at 1600° or 2000°C for 1/2 hr. The notched rods were then placed in a miniature Charpy-type impact machine and struck at their midpoint (opposite the notch) with a hammer designed to deliver 50 in.-lbs of energy. The strain rate at the base of the notch was estimated to be approximately 100 sec-1 at the instant of impact. The specimens were heated in situ to the desired impact temperature. The microstructures produced by the various anneals were studied by both X-ray diffraction and metallographic techniques. Fig. 1 reproduces the microstructures observed metallographically following a 10-sec electroetch in a 10 pct KOH solution. Fig. l(a) shows the elongated fibrous grain structure of the as-received material. Following the anneal at 1300" or 1400°C the grain structure was still elongated as shown in Fig. l(b) but the etch pits delineated dense polygonized dislocation arrays within many of the grains. Occasionally a relatively dislocation-free recrystallized grain was found growing into the matrix. The anneals at 1600° and 2000°C resulted in complete recrystallization and some grain growth. The grains produced at 1600°C were still slightly elongated as shown in Fig. l(c) whereas the anneal at 2000°C produced equiaxed grains. The changes in grain size produced the expected changes in the X-ray back-reflection patterns; there was no indication either in the as-received material or the annealed material of any preferred orientation. RESULTS a) Impact Behavior. Fig. 2 reproduces the ductile-brittle transition curves measured in the manner described in the previous section. It can be seen that under these testing conditions the as-received

Jan 1, 1964

The Library of the above-named Societies is open from 9 A.M. to 10 P.M., except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library, through its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information on the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is .desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape.

Jan 6, 1917

Members whose deaths were reported from Mar. 5, 1919, to Apr. 5, 1920. Elected Died 1895 ANDERSON, ROBERT HAY 1920 1916 ATWATER, M. W 1919 1905 BARD, D. C 1920 1893 BECKER, GEORGE F 1919 1914 BIGELOW, BRAXTON 1917 1917 BLACK, HERBERT F 1919 1911 BOWLER, ROBERT P 1919 1902 BROWN, ARTHUR H 1919 1913 BURNHAM, WILLIAM 1918 1905 Carnegie, Andrew 1919 1900 CARPENTER ROLLA C 1919 1908 CONNER H. MCKEAN 1919 1883 COOK, ROBERT A 1919 1903 COOPER, JOHN 1919 1875 CROXTON, SAMUEL W 1919 1889 DICKMAN, R. N 1919 1893 DUFOURCQ, EDWARD L 1919 1917 FAY, CHARLES H 1918 1875 FOHR, FRANZ 1919 1879 FRICK, H. C 1919 1880 GAYLEY, JAMES 1920 1917 GARVIN, JOHN C 1920 1915 GIBBS, CHARLES H 1919 1917 GODBE, RALPH T - 1918 GREGORY, A. E 1919 1917 HAMILTON, A. McL 1918 1914 HEISE, HENRY C - 1913 HINCKLEY, E. R 1918 1884 JENNINGS, HENNEN 1920 1895 JOHNSON, J. E., JR 1919 1895 KANN, MEYER M 1919 1895 KAYSER, H. W. F 1919 1918 KENNEDY, DANIEL J 1903 KING, PAUL S 1919 1901 LANGTON, JOHN 1920

Jan 1, 1923

The Library of the above-named Societies is open from 9 A.M. to 10 P.M., except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library, through its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information on the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral. matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape.

Jan 3, 1917

The Library of the above-named Societies is open from 9 A.M. to 10 P.M., except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library, through its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information on the geology and mineral resources of all countries. All communications should be made as definite as possible so that the, information received may be what is desired and not include collateral matter which may, not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape.

Jan 4, 1917

By Ralph Hultgren

IN solid solutions atoms of differing sizes occupy the same crystalline lattice, requiring that some of them be compressed and others expanded. The energy involved has been called misfit strain energy and is an important concept of crystal chemistry. If the atomic sizes and elastic constants of interatomic bonds are known, the misfit energy may be calculated,' provided certain simplifying assumptions are allowable. Usually, isotropic crystals are assumed and interatomic distances are taken to be the statistical average determined from X-ray diffraction. Such calculations yield values of the misfit energy of the order of 1 or 2 kcal per atom in alloys such as Au-Cu at compositions of 50 atomic pct. However, evidence has accumulated in recent times that atoms change their sizes with composition of alloys, implying electronic rearrangement of the bonds. The size changes have been found particularly by application of the X-ray method developed by Warren, Averbach, and Roberts.' Thus, Averbach, Flinn, and Cohen3 determined radii in Au-Cu alloys. Oriani4 showed that these new radii led to a calculated misfit energy in disordered AuCu, which was decreased from the values calculated by the usual theory more than twenty-fold, to only 80 cal per g atom. Thermodynamic calculations from the phase diagram5 also show misfit energy to be no more than a few hundred calories per g atom in this alloy. The question of what electronic rearrangements are possible therefore becomes compelling in estimating misfit energy. In the following pages the results of certain calculations on the AuCu tetragonal superlattice are submitted. Conclusions drawn from these should be applicable in large degree to disordered solid solutions. As in all ordered states, bonding distances in the superlattice are individually known, rather than being merely average distances as found from lattice constants of disordered states. Moreover, only the Au-Au and Cu-Cu distances are strained; the elastic constants of these are known in the elementary state. In the usual calculation it is necessary to assume elastic constants for Au-Cu bonds. Misfit energy has thus been calculable without the need of many simplifying assumptions usually made. It is still assumed that equilibrium bond lengths and elastic properties of the bonds are the same in the alloy as in the pure metals. As previously discussed, this is probably not correct. Also assumed is that the bonds are not affected by strain of neighboring bonds. A calculation of Young's modulus from compressibility data shows this to be far from true; extensive electronic rearrangements take place. It would seem that misfit energy cannot be calculated from elasticity data for the elements. The usual methods may, however, give an upper limit which is often much higher than the true value. The question of electronic rearrangement is, of course, a complex one. Pauling's theory gives a simple, approximate treatment of the relation between type of bond and bond distance. This has been applied with some success to the Au-Cu system, as will be shown in a later section. Misfit Energy in Au-Cu Alloys Hume-Rothery and Raynor6 discuss the Au-CU system as a type example of strain energy. The gold atom is 12.8 pct larger in diameter than the copper atom, near the size factor limit beyond which solid solubility is severely restricted. They therefore consider the misfit energy to be large, a conclusion for which they believe they find evidence in the phase diagram. Gold and copper are completely miscible in the solid state, but the alloy has a minimum melting point at an intermediate composition. From this Hume-Rothery and Raynor conclude that the strain energy is nearly large enough to prevent miscibility; the phase diagram tends toward a eutec-tic type. In Ag-Cu, which has almost identical size relationships, solid miscibility is quite limited; whereas in Au-Ag, where atomic sizes are nearly the same, there is complete miscibility without a minimum in the melting point. From their arguments the heat of formation of Au-Cu would be expected to be endothermic or only slightly exothermic, that of Ag-Cu to be endothermic, and that of Au-Ag to be exothermic. Deviations, from Ve-gard's law of additivity of atomic radii support these conclusions, since Au-Cu and Ag-Cu both have pronounced positive deviations, and Au-Ag has a negative deviation. Nevertheless, Au-Cu alloys form exothermically; indeed, considerably more exothermically than Au-Ag, Table I. Hence, strain energy must be much less important in this case than Hume-Rothery and Raynor have supposed.

Jan 1, 1958

By A. H. Daane, J. F. Haefling

BECAUSE of the wide use of platinum in industry and research, the physical properties of this metal, including its vapor pressure, have been studied in some detail.' The other members of the palladium-platinum group of metals have not been studied as extensively, and only qualitative information is available on the vapor pressure of palladium. Data given in literature by Vines1 and Brewer2 on the vapor pressure of palladium are based on the qualitative observations by Holborn and Austin3 and Crookes4 on the rate of volatilization of palladium filaments in various atmospheres. The general observation that palladium is the most volatile metal of the palladium-platinum metal group was corroborated by Bell, Love and Normand who studied the separation of isotopes of the platinum-group metals by a mass spectrometric method. We have measured the vapor pressure of palladium using the Knudsen effusion technique. In this work, the effusion vessel was suspended from a quartz-fiber microbalance into an induction furnace, and the amount of vapor effusing from the vessel was determined by direct weighing of the vessel during the measured heating times. This technique has been described in a report from this laboratory." The vapor pressure of palladium was calculated from these measurements using the equation P...... = 17.14 -W- (77m)'u [1] a t where ? is the weight loss in grams of vapor of molecular weight m from a vessel having an orifice of a sq cm, during t sec. The derivation of this equation from kinetic theory has been described in a previous report from this laboratory: as well as in texts discussing the kinetic theory of gases.%" Test Vessel—In the search for a suitable material for the effusion vessel, it was found that tantalum reacted with palladium metal to form intermetallic compounds, and graphite was readily dissolved in palladium metal to form what appeared to be a liquid phase at a temperature several hundred degrees below the melting point of palladium. On cooling, the graphite gathered into spherical balls in the palladium, with crystals extending radially from the center of these balls, some of which were a millimeter or more in diameter. However, palladium metal vapor did not attack the graphite vessel, so graphite could be used where it did not contact condensed palladium. Tungsten did not appear to react with palladium vapor or molten palladium at its melting point, but it was not convenient to use a tungsten-vapor pressure vessel because of the difficulty of fabricating this metal. Since the vapor-pressure range to be studied (10 2 to 10 ' mm) did not appear to extend above the melting point of palladium, a combination of tungsten and graphite served to provide a very satisfactory effusion vessel. The lower half of the graphite vessel was lined with some strips of tungsten foil and the sample of palladium consisting of a coil of sheet was placed in the tungsten liner; in this way, no contamination of the palladium by carbon occurred. Procedure After outgassing at 1500C, the tungsten-lined graphite effusion vessel was loaded with 300 mg of

Jan 1, 1959

By D. R. Hay, E. Scala

STUDIES of structure-sensitive properties, especially mechanical behavior, have shown that grain and subgrain structure play an important role. The mechanical properties of tungsten, in particular, are sensitive to the nature of the intergranular structure. Substructure and dislocation networks in single-crystal and polycrystalline tungsten have been studied by Nakayama et al.' Various orders of substructure were observed ranging from a microscopic first order (grain diameter: 2 to 8 mm) to a microscopic second order (grain diameter: 50 to 300 p), and, within the latter, dislocation networks forming an even smaller order of substructure. In their single crystals, grown by arc fusion, the degree of misorientation in each order was small: 16'3OU, -11, and -10" for the first-, second-, and third-order substructure, respectively. To study the properties of polycrystalline tungsten, powder metallurgy tungsten is generally used. However, in a mechanical property investigation, the zone-melted or arc-fusion crystals are more desirable than the powder metallurgy product due to their higher purity and absence of porosity and other defects inherent in consolidation by powder metallurgy. Grain boundaries can also be produced in melted stock by working and recrystallizing. However, material with subgrain mis orientations of the order of several degrees (high-angle substructure) has not been reported previously and is the subject of this communication. Crystals were grown by electron-beam, floating-zone melting. The starting material, Sylvania Pure-tung welding rod, was given one zone pass at a traversal rate of -2 mm per min. Through control of the zone temperature, it was possible to influence the degree of crystal perfection. By maintaining the zone at a high degree of superheat, high-perfection crystals could be grown. However, at temperatures only slightly above the melting point, the zone-melted crystals contained a high-angle substructure. A sensitive control of the zone temperature was not possible due to the difficulty of estimating the temperature of the zone and of providing a constant supply of power to the sample. Therefore, an empirical method, using the shape of the molten zone as a criterion, was adopted as an indication of temperature. At high degrees of superheat, the surface tension of the molten zone decreases and a neck forms at the top of the zone, whereas at low zone temperatures the diameter of the zone remains reasonably uniform. Although it was not possible to obtain a continuous variation of misfit angle, the conditions could be directed toward the growth of either high- or low-angle substructure by maintaining only a slight neck in the zone (sufficient to establish that it was molten) or a well-necked zone, respectively. Mass spectrographic analyses of both types of material revealed no significant differences in the concentrations of their impurities. The degree of misorientation at high angles was obtained by measuring the angular spread of spots corresponding to a single reflection on a Laue back-reflection photograph. Fig. 1 shows a typical Laue back-reflection photograph of a crystal with a 3-deg spread. By measuring the angular deviation of the spots corresponding to a single reflection from the mean center of the spots around which constant angular deviation contours were drawn, an average angular spread of misfit could be calculated. The angular average was weighted by the number of spots observed in each angular interval. At angles greater than 5 to 6 deg the spots from different reflections begin to overlap, and cannot be associated with a particular reflection. Laue back-reflection photographs taken at different locations on samples .with approximately 3-deg spreads showed only a small difference in angular misorientation, less than 8' of arc, within individual specimens. The microstructure was examined using Berg-Barrett X-ray extinction contrast microscopy. Berg-Barrett photographs taken directly on the as-grown surface, Fig. 2, show an essentially equiaxed subgrain structure of -0.1 mm in average grain diameter in both high- and low-angle crystals. Fig. 2(a) is a photograph of a sample with a low misfit angle and Fig.

Jan 1, 1968

Arizona ROBERT E. TALLY, Chairman CARL E. ~IILLS, Secretary-treasurer, P. 0. Box 1462, Jerome. Ariz. W. S. BOYD THOMAS H. 0. O'BRIEN F. W. MACLENNAN Boston Meets first Monday each winter month GAL~N H. CLEVENG~, Chairman HOLCOMB J. BROWN, Vice-chairman F. I,EROY FOSTER Secretary-treasurer Room 8-219, Mass. lnst: of Tech., Cambridge Mass. A. E. WELLS H. A. WENTWORTH

Jan 1, 1928

By H. I. Smith

CONTENTS [PAGE Problems of Mining and Processing Mineral Aggregates (TP 1649, by NATHAN C. ROCKWOOD, Min. Tech., Nov. 1943. Discussion by H. I. SMITH, IRVING WARNER and the author) t Mica in War (TP 1749, by RUSSELL G. WAYLAND, Min. Tech., July 1944. Discussion by H. S. SPENCE) 3 Three Roofing-granule Plants in Pennsylvania (TP 1787, by RICHARD M. FOOSE, Min. Tech., Jan. 1945. Discussion by H. I. SMITH)5 Methods of Prospecting and Mining Optical Calcite in Montana (TP 1896, by E. W. NEWMAN, Min. Tech., Nov. 1945. Discussion by W. C. STOLL and FRANK C. ARMSTRONG, and the Glass Sand and a Glass Industry in Puerto Rico (TP 1939, by HOWARD A. MEYERHOFF and J. EARL FRAZIER, Min. Tech., Nov. 1945. Discussion by A. M. SHORT, the author and PHILIP The "Bonanza" Mica Operation of Purdy Mica Mines, Limited, Mattawsn Township, Ontario (TP 2154, by HUGH S. SPENCE, Min. Tech., March 1947. Author's supplement and discussion by JOHN A. BAKER, E. J. LINTNER, and the author) 7 Process for Manufacture of Dead-burned Magnesite and Precipitated Calcium Carbonate from Dolomite (TP 2155, by ROBERT D. PIKE, Min. Tech., March 1947. Discussion by 0. C. RALSTON and the author) 9] Problems of Mining and Processing Mineral Aggregates H. I. SMITH*-Mr. Rockwood has presented a very interesting paper on problems of the mineral aggregate industry in meeting specification requirements, which apparently are ever decreasing in tolerance. May I call attention to a method of mineral separation that may be of value in separating the flat aggregate particles from the more angular ones and possibly the soft particles from the hard. The method is the old Pardee spiral coal separator, extensively used many years ago in the anthracite region for separating rock and bone from anthracite coal.1 The success of the process depends on the relative coefficient of friction of the aggregate particles to be separated rather than on their relative specific gravity. The flat and the soft particles normally will slide more slowly and stay on the inner spiral until they reach the delivery spout at the bottom whereas the round and the angular pieces will work to the outer edge and fall off into a spiral of larger diameter. The capacity of the separator is increased materially by having three inner spirals, with a separate feed for each, on which the particles travel more slowly, and one outer spiral from which the more rapidly traveling pieces slide to the bottom. IRVING WARNER*-I have long been convinced that much of the equipment and methods developed for mineral dressing might be advantageously employed in the mineral aggregates industry, and more particularly in the production of sand and gravel. The two industries are not well acquainted with each other or their problems. They have separate trade publications. The difficulty with the situation is that there are few large sand and gravel plants and few provided with technical services in their own organization or by retainer. This does not refer to engineering organizations but rather to improvement of plant technic in processing.

Jan 1, 1947

By Irving B. Cadoff, Alvin A. Machonis

The resistivity, Hall coefficient, Seebeck coefficient, and thermal conductivity were measured as a function of temperature for cation-rich alloy single crystals covering the composition range across the PbTe-SnTe system. Alloying of PbTe with up to 20 pct SnTe was found to have little effect on the energy gap. Above 20 pct SnTe the alloys were "p" type but below this range the sign could be varied by heat treatment. The lattice thermal resistivity of the compounds SnTe and PbTe is raised by alloying one with the other. Z values in the order the interesting values obtained. THE PbTe-SnTe system has several interesting features. For one, PbTe is a useful thermoelectric material and the possibility of improving its figure of merit by alloying with SnTe, an isomorphous compound, has been suggested since these pseudo-binary solid solutions generally have a more favorable ratio of electrical conductivity to thermal conductivity than either of the components.' Other interesting features relate to the conductivity mechanism, band structure, and stoichiometry of the compounds and their alloys. PbTe is a semiconductor with an energy gap of about 0.29 ev2 at room temperature whose conductivity sign and magnitude can be varied from "n" to "p" by controlling the proportion of lead and tellurium with respect to the stoichiometric ratio.3 Excess lead results in "n"-type conduction. SnTe is found to exist only as a "p"-type material of relatively high conductivity. This behavior is attributed to stoichiometric deviation by Brebrick4 but Sagar and Miller proposed that the behavior of SnTe must be due in part to the presence of an overlapped band. An investigation of alloys of this system, therefore, might give additional information which would permit one to evaluate which of the two proposals is the more appropriate one. Abrikosov et al.' studied the room-temperature electrical properties of these alloys and reported data for Seebeck coefficient and resistivity on poly-crystalline alloys. The present work is a more exhaustive survey of the PbTe-SnTe system. Re- sistivity, Hall coefficient, Seebeck coefficient, and thermal conductivity were measured over a wide temperature range for single crystals at 10-pct intervals of lead/tin ratio across the pseudobinary system. The relative concentration of tellurium was controlled so as to obtain metal-ion excesses in all cases. SAMPLE PREPARATION The crystals were prepared by melting elemental lead, tin, and tellurium in weighed proportions in evacuated Vycor capsules. The lead and tellurium were high-purity grades obtained from American Smelting & Refining Co. The tin was supplied by Comico. The proper calculated proportions of lead, tin, and tellurium were weighed and charged into prepared Vycor capsules prior to evacuation. The capsules were prepared from 15-mm Vycor tubing. A sharp point was worked on one end of the tube. A pyrolytic graphite coating was deposited on the Vycor walls by heating the tip to 800°C in an atmosphere of acetone-saturated argon. An additional coating of graphite was deposited on the pyrolytic coating from an Aquadag suspension. Above the coated tip the tube was reduced in diameter to form a constrictive neck. To avoid scratching the graphite coatings the charge was placed in the tube above the constriction. After a low-temperature bake, the evacuated capsule was sealed. On subsequent heating the charge melted down into the lower portion of the capsule. The crystals were grown by lowering the capsule through a Bridgman-Stockbarger furnace. The lowering rate was 1 in. per 8 hr. The upper portion of the furnace was set for 950°C and the lower portion for 800°C. In general the yield of single crystals was about 25 pct. The mixed compositions were, as expected, the most difficult to grow. The finished crystals were sectioned into 5/8-in. slices. The tip, end, and middle slices from each crystal were analyzed by X-ray fluorescence to determine the lead-to-tin ratio. The resulting values were used to plot a composition vs distance plot for each crystal. Slices were selected from each crystal, with the aid of the composition plots, to cover the complete range of compositions at 10-pct intervals. In general, the slices selected were taken from the seed end of the crystal where the longitudinal segregation (as determined from the X-ray fluorescence analysis) was a minimum. Laue single-crystal analysis and metallographic analysis was used to verify if a slice was single or polycrystal. Any grain boundaries were clearly visible in the as-cut and polished condition. In ad-

Jan 1, 1964

By K. H. Nimerick, B. E. Scott, F. J. Beafore

A unique freeze conditioning agent (FCA) which functions by forming structurally weak ice rather than suppressing the freezing point of water has been successful in alleviating frozen coal problems. Frozen coal treated with FCA has been quickly unloaded at temperatures below -17.8OC (O°F). Other applications of FCA include deicing: conveyor belts, idler, idler arms, and other moving parts that have been impeded by ice.

Jan 1, 1980

By L. E. PORTNER

INCREASING military demands on the petroleum industry have brought into bold relief the crude-oil reserves now available to meet combined military and civilian demands, emphasizing the necessity for a greater efficiency in recovery from what has been discovered than ever before, particularly in light of the absence of new discoveries. This situation-and the fact that the industry, as well as members of the Government charged with governing oil production, desire to meet all crude-oil demands made of the industry with the least loss in tangible reserves through production practices-paves the way for increasing application of sound principles of production engineering and conservation.

Jan 1, 1944