Search Documents

By W. C. Elli, M. E. Fine

YOUNG'S modulus of elasticity in metals ordinarily decreases with rising temperature. The range of the thermoelastic coefficient at room tem- 1/E dE/dT perature (temperature coefficient of modulus, is illustrated1 by the values for tungsten and hard-drawn aluminum, —95 and —1220x10-6 eg C-1. However, a nearly zero thermoelastic coefficient is observed in some ferromagnetic alloys over a limited temperature range. In these alloys, as the temperature is raised, an increase in modulus arising from loss of ferromagnetism compensates the normal decrease. Iron-nickel alloys containing 36 to 52 pct Ni behave in this manner. In the present investiga- tion, the dependence of the modulus and thermo-elastic coefficient on cold working and annealing were studied in iron-nickel alloys in this range of nickel. Although these alloys, when fully annealed, have a coefficient near zero over a very small temperature interval, the temperature range of low coefficient can be extended greatly by straining and then stress-relief annealing. The modulus of face-centered cubic iron-nickel alloys annealed at 1000°C does not vary linearly with composition at room temperature but, as shown by the solid line of fig. 1, from Koster,' is minimum at 40 pct Ni and maximum at 87 pct Ni. The modulus increases with applied magnetic field but retains the minimum near 40 pct Ni. Schematic change of modulus with temperature for three compositions is shown in fig. 2.'. ' With increasing temperature, the slope becomes less negative, goes through zero (temperature of minimum modulus for the alloy), becomes positive, and resumes its normal negative value above the Curie

Jan 1, 1951

COUNCIL OF NATIONAL DEFENSE W: S. GIFFORD, Director, GROSVENOR B. CLARKSON, Secretary. The Council of National Defense The Advisory Commission NEWTON D. BAKER, DANIEL WILLARD, Chairman, Secretary of War, Chairman.. (Transportation). JOSEPHUS DANIELS, BERNARD M. BARUCH, Secretary of the Navy. ' (Raw Materials). DAVID F. HUSTON, HOWARD E. COFFIN, Secretary of Agriculture. (Munitions, Manufacturing). FRANKLIN K. LANE, HOLLIS GODFREY, Secretary of the Interior. (Science and Research, including En¬ WILLIAM C. REDFIELD, gineerlng and Education). Secretary of Commerce, SAMUEL M. GOMPERS, WILLIAM B. WILSON, (Labor). Secretary of Labor. F. H. MARTIN, (Medicine and Sanitation). ' JULIUS ROSENWALD, (Supplies). At the request of Dr. Hollis Godfrey, Chairman of the Advisory Committee On Science and Research, which includes Engineering and Education, a Sub-Committee of Engineering Societies has been appointed with representatives as follows:

Jan 6, 1917

By AIME

The following corrections (in italics and bold face) were received too late for the September issue of Transactions: Page 270, Abstract, line 1, spelling should be goethite. Page 270, column 1, authors' box, authors' affiliations should read: L. A. BAKER, formerly Principal Research Scientist, is Pellet Plant Superintendent, Cliffs Western Australian Mining, Cape Lambert, W. A., Australia. C. G. THOMAS is Experimental Officer, Minerals Research Laboratories, C.S.I.R.O., North Ryde, N.S.W., Australia. R. J. CORNELIUS and K. S. LYNCH are General Superintendent, Product and Process Development, and Superintendent, Pellet Plant, respectively, Hamersley Iron Pty. Ltd., Dampier, W. A., Australia. G. J. ARMSTRONG, formerly Chief Metallurgist, Hamersley Iron Pty. Ltd., is Mill Superintendent, Samin Ltd., Burra, S. A., Australia. Page 271, column 2, line 41, should read "highest possible spalling temperature and to adjust the. . :' Page 275, column 1, line 1, should read "(LOI) figures are shown in Table 1 and vary from 2.61..." Page 275, column 1, line 16, spelling should be goethite. Page 276, column 2, line 6, should read "Predicting Grate Speed and Production Rate: The cor-..." Page 276, column 2, line 8, should read "basis of Blends A, B, C, D, and Plant Ore 1, shown in Table..." Page 276, Table 3, heading under "Prediction Method" should read Blend E. Page 277, column 1, line 38, should read "=293 tph of specification pellets (see Table 1 for loss-..." Page 277, column 2, replace caption for Fig. 14 with the following: Fig. 14-Example of calculation of hood temperature profile during downdraft free-water drying, given plant free-water drying time. Page 277, column 2, replace caption for Fig. 15 with the following: Fig. 15-Example of calculation of hood temperature profile during drying, given plant goethite drying time.

Jan 1, 1974

By James Douglas

Discussion of the paper of James Douglas, presented at the New Haven meeting, February, 1909, and published in Bulletin No. 29, May, 1909, pp. 439 to 451. JAMES DOUGLAS, New York, N. Y. (communication to the Secretary*) :-In my paper on the Conservation of Natural Resources, I referred to the slow replacement of bee-hive ovens by the by-product ovens as a most notable instance of waste. And I quoted from Mr. Parker's report for .1906 an explanation given by him in accounting for the small production of by-product coke. It was that the markets for the by-products of the coke-ovens was so limited that some of the ovens constructed were out of operation. His report on the manufacture of coke in 1908 1 does not record an improvement, and attributes the strange fact that we alone, of all the industrial peoples, delay the adoption of this cardinal improvement from the continuance of the same almost inexplicable cause. To quote again from his report, lie says (p. 241): "The year 1908 was not marked by any notable gain in the construction of by-product coking plants, though some new work was done. There was a net increase of 115 in the number of completed ovens in 1908 over 1907, the totals for the two years being, respectively, 3,892 and 4,007. The additional equipment consisted of 140 Koppers regenerative ovens built at Joliet, I11., by the United States Steel Corporation, but this increase was partly offset by the dismantling of Y5 Semet Solvay ovens at Sharon, Pa., the net gain being 115 ovens. Included in the total of 4,007 completed ovens in 1908 are 152 Newton-Chambers ovens at Vintondale, Pa., but as no recovery of by-products was made at this plant in 190S, the production of coke is included with that from beehive ovens. The 56 ovens of the same type at Pocahontas, Va., have not been in practical operation since they were first. installed. In addition to these there was one other by-product plant of 120 ovens. Oat. was not operated during the year. The number of retort ovens producing coke in 1908 was 3,679, as compared with 3,811 active ovens in 1907." In describing the anomaly he says (p. 249): It has been contended that the development of the by-product coking industry would have shown more rapid progress if markets for the by-products were * Received Feb. 2, 1910. Mineral Resources of the United States for 1908, Part I1., U. S. Geological Survey (1909).

Apr 1, 1910

By George W. Pawel

OWING largely to its value as a toughener and strengthener of steel for both industrial and military purposes, nickel is playing, an important role in the current war. It is fine of the metals in which the Allies enjoy a definite edge over the Axis nations and this time there is no place to which the Germans may send another submarine "Deutsehland" and expect to pick up a cargo of nickel to replenish their exhausted supplies. Total world nickel production thanks almost entirely to the expanded operation of the International Nickel Co. of Canada at Sudbury must now be at the rate of around 175,000 tons a year scarcely more than 5 per cent of which is accounted for by Germany, Italy and Japan. This represents more than four times the world output at the end of the first World War.

Jan 1, 1943

By G. A. Croes, N. Schwarz

This paper reports the results of a series of model displacement experiments carried out for measuring the efficiency of the water-drive process. This series forms a continuation and extension of that described by Engel-herts and Klinkenberg. Detailed information has been obtained on the influence of the oil/water viscosity ratio. The results are represented in the form of a diagram from which both the oil recovery and the water/oil ratio can be easily read off as a function of the total production (oil plus water) for all values of the viscosity ratio M between I and 500. These resu1ts are viewed in the light of the two existing theories on water flooding, viz. that of Buckley and Leverett and that of Dietz. It is shown that if the Buckley-Leverett theory applies, the relation between the relative permeability ratio and saturation, which plays a major role in this theory, (.an be calculated with a high degree of accuracy from the results of the model experiments. Dietz's theory is found to be in agreement with the experimental results in a certain range of circumstances. A discussion of the physical background of the Buckley- Leverett and Dietz theories makes it clear why the latter fails to agree with some of the experimental results. INTRODUCTION For an economical exploitation of oil fields both a rational control of natural (primary) recovery processes and a proper application of artificial (secondary) recovery methods are essential. These require detailed information upon the dependence of the relevant flow processes on the variables by which they are governed. Three methods are available for obtaining this information: (1) (statistical) analysis of actual field data; (2) appropriately scaled model experiments; and (3) mathematical analysis of the physical problem. If sufficient data were available, the first method would, in principle, be the most reliable one, although it has the drawback that the basic relationships between the variables involved are to a large extent obscured by the natural inhomogeneities of most reservoirs. The most profitable procedure seems to be: (a) determining the fundamental relations for idealized reservoirs by methods (2) and (3); (b) checking the consistency of the results obtained by these two methods; and (c) establishing the range of applicability of these methods to actual reservoirs by comparison with the data accumulated under (1). In this paper items (a) and (b) are dealt with for the case of homogeneous loose sands initially saturated

Jan 1, 1956

DETAILED programs for the Regional Meeting to be held at Boston, on Aug. 29, 30, 31, will be available on arrival at the Copley-Plaza Hotel, where registration will begin at 10 a. m. on Wednesday morning. The opening session will be non-technical in character and will be called to order at 11 a. m. Hector J. Hughes, Dean of the Graduate School of Engineering of Harvard University, and others will speak, and in the afternoon visits are to be made both to Harvard and Massachusetts Institute of Technology. Wednesday afternoon will be devoted mainly to the opening of an exhibit of geophysical instruments and methods at Tech. On the way back to the hotel a tour of Old Boston will permit the visitors to see many of the historic points of the city. A special meeting of the Board of Directors has been called to be preceded by the usual subscription dinner at the University Club at 6.30 p. m. Owing to limita-tions of room, invitations have been sent only to the usual list designated in the By-Laws, the Directors, past officers, chairmen of sections and of technical committees. The dinner and a brief business session of the Board will be followed by a technical session at the Copley-Plaza at 8 p. m. and this in turn by a buffet supper at the University Club at 10 p. m. Sep-arate entertainment is being provided for the women for the evening. Thursday will be devoted to technical sessions both in the morning and afternoon. If necessary to permit adequate discussion, an overflow session will be ar-ranged in the afternoon. In the evening, a subscription dinner will be given at the Copley-Plaza at which past-presidents John Hays Hammond and Robert H. Rich-ards will be guests of honor. It is promised that speeches will be short and dancing will be arranged for following. The women will be offered a luncheon and bridge party at one of the country clubs on Thursday, and Friday will be devoted to an all-day excursion for both men and, women. Members are asked to register promptly on arrival so that the various committees will know as early as possible for how many to provide. The major part of the technical program has been provided by the Committee on Geophysical Methods of Prospecting, and a series of papers of great value and interest in this new field has been brought together. Abstracts of substantially all of them are printed in this issue of MINING AND METALLURGY and the papers themselves will, with one or two exceptions, be avail-able in printed form at the meeting and later in the regular publications of the Institute.

Jan 9, 1928

FRank FirmstoNe, Easton, Pa.: The effect of lead on brass seems to have been recognized by Berthier, and the facts published by him as early as 1818 (Ann. des Mines, 1st ser., iii., 1818, p. 347 et seq.). He there says expressly that copper containing lead makes " dry " (see) brass, and that, for the same reason, blast-furnace

Jan 1, 1898

By H. C. Gatos, J. T. A. Pollock, V. Sadagopan

PREVIOUS investigations on the effect of neutron irradiation on the superconducting properties of bulk transition metals indicated that little or no change occurred in poly crystalline disordered materials, particularly if cold-worked prior to irradiation. Only the superconducting properties of ordered intermetal-lic A15 compounds were found to be sensitive to irradiation, and the observed reduction in Tc and increased magnetic hysteresis or critical current densities were attributed to the introduction of flux pinning vacancy clusters and disorder in the lattice. Since the former would also be expected to be present after irradiation in disordered alloys, the general conclusion was that the disordering effect of the irradiation was the primary reason for the changes observed. The present note reports some unusual effects of neutron irradiation on cold worked Nb(Cb)-Ti-V alloys. Specimens with nominal composition as given in Table I were prepared by repeated arc melting, taking the usual precautions, and homogenized at 1000°C for 24 hr prior to a reduction of 15:l by cold rolling. Samples of size 1 by 1 by 25 mm were sliced from the rolled strips. The sarmples chosen for irradiating were sealed in a cadmium tube (wall thickness 1 mm) prior to exposure in a fast neutron flux of 3.7 x 1019 neutrons per sq cm in the swimming pool reactor of Union Carbide Corporation&apos;s Sterling Forest Reactor. During irradiation the temperature of the samples was maintained below 70°C. The irradiated samples were stored at room temperature for approximately 1 year allowing the radiation levels to reach a safe handling value. Tc measurements were made employing a self-inductance coil technique. Jc data at 4.2"Kwere obtained using a four lead resistivity method. The latter measurements were made at the Francis Bitter National Magnet Laboratory by setting the perpendicularly applied field and increasing the direct current through the sample until a potential of about 10-6 v was detected. Tc values for the nonirradiated samples are listed in Table I together with the change in Tc after irradiation. A decrease in Tc of 0.25 or 0.3"K was measured for three of the four samples, the exception being the Nb-30 at. pct V-20 at. pct Ti alloy which showed a decrease of 0.5K. Jc vs applied field data are plotted in Fig. 1 for the Nb-20 at. pct V-30 at. pct Ti alloy. These curves are typical of the four alloys and surprisingly indicate that a degradation occurred in all the samples after irradiation. Hc2 values, obtained by extrapolation to zero current, are 8 to 15 pct lower than those measured for the nonirradiated specimens. The reasons for the degradation of Tc and jc ob-served in the alloys on exposure to neutron irradiation are not immediately apparent. The temperature at which the samples were maintained during bombardment (<70°C) and stored (20°C) make it highly unlikely that any significant change in the dislocation density of the materials through thermally activated migration and annihilation would occur. The explanation must lie in the type of damage produced by the bombardment. McEvoy et a1. reported no change in superconduct-

Jan 1, 1970

By G. R. Speich

The precipitation of the Feab and Fe,Ti Laves phases (MgZn, type, C14) from Fe-Nb and Fe-Ti solid solutions, respectively, has been studied in the temperature range 500" to 800°C using hardness measurements, light and electron microscopy, and X-ray and electron diffraction. The Fe-Nb alloys contained 0.96, 1.67, and 3.80 pct Nb and the Fe-Ti alloys 3.5, 5.8, and 8.8 pct Ti. In both systems only the equilibrium Laves phase is formed, with nucleation occurring at grain boundaries, at dislocations, and in the matrix. No cellular precipitation or transition phases were observed. The precipitation of the Laves phase in a fine dispersion leads to significant hardening in both systems. The hardness of the aged alloys is proportional to the reciprocal of the square root of the interparticle spacing. The maximum solid solubility of titanium in a! iron is 9.0 pct Ti at 1280°C. THE precipitation of the FezNb and FezTi Laves phases (MgZn2 type, C 14) from Fe-Nb and Fe-Ti solid solutions, respectively, has been investigated as part of a continuing study of the mechanisms of precipitation from ferritic binary iron-base alloys. The iron-rich portions of the Fe-Nb and Fe-Ti phase diagrams are shown in Fig. l(a) and l(b). The Fe-Nb diagram is essentially that given by ansen&apos; with the more recent work of Hume-Rothery and Gibson2 added. Goldschmidt3 indicates that the FezNb Laves phase has a solubility extending from 32 to 55 wt pct Nb. The Fe-Ti diagram is also essentially that reported by Hansen.l The recent results of Nishimura and kamei, Murakami, Kimura, and Nishimura,&apos; indicate that the FezTi Laves phase has a solubility extending from 22.5 to 30.5 wt pct Ti. The L/6 + FezTi eutectic temperature of 1298°C indicated by Kornilov and oriskina&apos; has been adopted. The addition of niobium or titanium to iron lowers the 6 — y transformation temperature and raises the y — a! transformation temperature. This results in a closed y field in the Fe-Ti system, but the lower solubility of niobium in a! (6) iron results in a eutec-toid, 6 — y + FezNb, at 1200°C, and a peritectoid, y + FezNb —-a, at 989°C in the Fe-Nb system. The maximum solubility of niobium is reported to be 4.5 wt pct in 6 iron,&apos; 1.0 wt pct in y iron,7 and 1.8 wt pct in a iron.&apos; Some results from the present work indicate that the maximum solubility in a! iron is actually less than 0.96 wt pct Nb. The maximum solubility of titanium in a! (6) iron is somewhat uncertain since the early work of To faute and Butting-haus indicated a value of 6.0 wt pct while later work of Kornilov and Boriskina6 yielded a value of 14.0 wt pct. The present work indicates that the maximum solubility is actually 9.0 wt pct. In both systems the phase in equilibrium with the iron-base solid solutions is a Laves phase (Mg znztype, C14), FezNb or FezTi. Both of these Laves phases have a wide range of Solubility. The precipitation-hardening behavior of Fe-Nb or Fe-Ti alloys has not been studied extensively. Genders and Harrison&apos; reported that binary Fe-Nb alloys hardened upon aging. Peter and Fisher7 studied the mechanical properties of Fe-Nb and Fe-Ti alloys quenched from different phase fields.

Jan 1, 1962

By E. C. W. Perryman

The recovery and recrystallization characteristics of superpurity aluminum have been investigated using electrical resistivity, X-ray line breadth, and hardness measurements for the former and the micrographic method for the latter. The three different properties recover at different rates and have different activation energies. The recrystallization results agree well with Avrami&apos;s theory and furthermore indicate that the perfect subgrains formed during recovery are not the nuclei for re-crystallization. WHEN a metal is plastically deformed, its physical and mechanical properties generally undergo considerable changes and by subsequent annealing these changes are partly or wholly annihilated. Thus, a recovery process can be discussed, taking this term in its general sense. In practice, however, there is reason to discriminate between two apparently different processes, one most easily followed at low temperatures, in which the properties return to an almost constant value between that of the cold worked and fully annealed material, and a second process in which the properties return to their original values before cold working and which is accompanied by the formation and growth of new grains having an orientation different from that of the matrix. In this paper the word recovery will be taken to mean the changes in some property as a function of annealing time which occur either without the appearance of new grains or under conditions such that the new re-crystallized grains are very small (= 2 microns), are very few in number, and substantially do not affect the property being measured. This definition is rather abitrary, for it will depend upon the sensitivity of the technique used for the observation of new recrystallized grains, which in the present work was about 1 to 2 microns. However, it is helpful to use the term recovery in this sense and to reserve the term recrystallization for the processes of nucle-ation and growth of new grains in the cold worked matrix. Although considerable work has been done on recovery and recrystallization, most workers have based their study on the measurement of one or perhaps two parameters. Since very small amounts of impurities have such a profound effect on the recrystallization characteristics of a pure metal, it becomes extremely difficult to correlate one piece of work with another. With this in mind, the present work on recovery and recrystallization was done on the same material. Experimental Procedure Material Used and Fabrication: The composition of the superpurity aluminum used throughout this investigation was 0.002 pct Cu, 0.003 pct Fe, 0.003 pct Si, and <0.001 pct Mg. The ingot was hot rolled to 0.250 in., annealed, and cold rolled to 0.034 in. A large number of reductions and intermediate anneals were carried out so as to produce material with a minimum of preferred orientation and maximum homogeneity. For the recovery part of the investigation, the final cold reduction was 20 and 80 pct and for the recrystallization part, 20 pct. After each pass in the cold rolling process, the material was quenched in cold water in order to keep the rolling temperature as near room temperature as possible. Annealing Procedure: For the recrystallization work, specimens 1x1 in. were cut from the 0.034 in. cold rolled sheet and a hole was drilled in each through which a wire was threaded to support it in the salt bath. The temperature of the salt bath was controlled to +2°C and the time taken for a specimen to reach temperature was approximately 5 sec. These 1 in. squares were then divided into three groups, one of which was given 5 min at 318°C and another 2 hr at 244°C. These treatments were such that recovery was almost complete and a well defined subgrain structure produced. Separate specimens of each group were annealed for different times at 301°, 318°, 355°, and 373°C, i.e., three specimens for each annealing time. The delay between finish of cold working and start of annealing was about 1 hr. For the recovery work, strips 0.062 in. thick were cut from the cold worked sheet, annealed, and then given the last cold rolling operation. This was done for each annealing temperature. By this means it was possible to minimize the delay between cold working and annealing. In general, all measurements were carried out within 1 hr of the last cold rolling operation. Annealing at low temperatures was done in an oil bath the temperature of which was maintained constant to +1°C. Electrical Resistivity Measurements: Strips 20x0.5x0.05 in. were machined and the electrical resistance measured using a Kelvin double bridge. Measurements were made in an oil bath maintained at 20rt0.1°C. The same specimen was used for the complete isothermal annealing curve.

Jan 1, 1956

By G. B. Craig, H. E. Rosinger, W. J. Bratina

NUMEROUS studies have been reported on how the mechanical properties of a bcc metal are affected by interstitial solute atoms in the temperature range where appreciable diffusion occurs in finite time. Only recently, though, has work on an "interstitial-free" iron been reported, this by Leslie and sober,&apos; on an Fe-0.15 pct Ti alloy. The data was limited to a maximum temperature of 296°K. This work presents a systematic study of the flow stress and the activation volume of a similar material as a function of plastic deformation over the temperature range 253" to 473°K. The material studied was Ferrovac E iron containing 0.01 wt pct C and 0.0002 wt pct N annealed at 870°C for 1 hr, and the same iron with an addition of 0.15 wt pct Ti annealed at 870°C for 80 hr; cooling rates being 75°C per hr. In the latter alloy depletion of interstitials in the a-iron matrix associated with the second phase formation was expected. The temperature dependence of the flow stress was measured at 6 = 3.33 x 10-5 sec-1 from 253" to 473°K as a function of the deformation in 0.01 intervals from 0.03 to 0.12 strain. Results for two strains, 0.03 and 0.09 are shown in Fig. 1. The flow stress increased and reached a maximum in the Ferrovac E iron with increasing temperature, but showed a consistent gradual decrease in the Ferrovac E-0.15 pct Ti alloy. A yield point and Luders region, observed in Ferrovac E, was absent in the Ferrovac E-0.15 pct Ti alloy. Also, the Ferrovac E exhibited a serrated stress-strain behavior in the temperature range 330" to 400°K; dynamic strain-aging characteristics were absent for the titanium alloy. The activation volume was determined over the same temperature range by the method of stress relaxation at constant strain. Results are shown in Fig. 2. At the temperatures of serrated stress-strain behavior in Ferrovac E the activation volume was found to increase toward infinity and, as the temperature rose, to decrease, to about 100 to 200 v/b3. By contrast, the activation volume for the Ferrovac E-0.15 pct Ti alloy tended to increase continuously from the initial value of approximately 300 at 300°K to more than 800 at 473°K. Above 400°K, then, the corresponding activation volume values of Ferrovac E were less than that of the Ferrovac E-0.15 pct Ti alloy. The activation volumes, Fig. 2, appear to depend on dislocation-interstitial interaction in Ferrovac E and on dislocation-dislocation interaction in Ferrovac E-0.15 pct Ti alloy. The gradual increase in the latter metal is associated with thermally activated motion of dislocation segments.&apos; The decrease of the activation volume in Ferrovac E above 400°K is probably related to the diminishing effect of interstitials on dislocations. Here, the interstitials can be moved along with a dislocation without appreciable drag. As indicated in Fig. 1, removal of interstitials

Jan 1, 1970

The Library of the above-named Societies is open frond 9 A.M. to 10 P.M., except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated front sources of information. To these the Library, through Its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining neaps, and to furnish general information on the geology and mineral resources of all countries. All communications should he made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be, sent more promptly and in more usable shape.

Jan 1, 1917

The first of the two fall meetings of the Petroleum Division was held at Los Angeles, Oct 1-2 The attendance was the largest at a Coast meeting of the Division The Institute was officially represented by President Lovejoy, Secretary Parsons and George Otis Smith There were four sessions Thursday afternoon and evening, the latter a dinner meeting (both at the University Club), and Friday morning and after- noon, these two in the auditorium of the Edison building Possibly a dozen papers were presented, all of them constituting a valuable contribution to petroleum technology Hallan N Marsh, Chairman of the Division, presided at the dinner meeting at which Dr Smith addressed the members on "The Kettleman Plan m Retrospect," and C M Nickerson talked on the "Buena Vista Hills Cooperative Development Plan "

Jan 1, 1937

By Larry A. Shiprnan

DEMANDS upon power plants by the war program in 1941 intensified problems of coal utilization. It was an outstanding year in that field. The domestic heating stove witnessed outstanding development; the research folks progressing so rapidly that the design of the "perfect" stove is just around the corner. Use of colored motion pictures in analyzing fuel-bed performances has reached a new high with the colored pictures taken at minute intervals and projected at sixteen frames a second as shown by the Koppers Coal Co. and the Anthracite Institute (on domestic stokers) and the Consolidated Edison Co. (industrial stokers). Continued efforts of this kind will be beneficial in analyzing further some of the "Code for Testing Coal" problems confronting Subcommittee No. 2 of the Joint A. I. M. E. - A. S. M. E. Committees.

Jan 1, 1942

By C. J. Rodgers

The present day success of gravel packs to prevent or retard the migration of unconsolidated sands into the well bore is due to: (I) the use of a saline or non-aqueous, nonsolids drill fluid, (2) proper preparation of the well bore prior to gravel packing, and (3) pressure placement of the gravel. The experience gained from the "pressure pack" method of gravel packing indicates that sand-free fluid production can be maintained for a length of time sufficient to make the operation economically attractive. Data pertaining to the first 15 wells so completed by Gulf indicate that for each dollar spent to effect the completion, there will be a return of more than $2.92. The pressure pack technique of gravel packing is essentially the placing of gravel in and adjacent to the producing formations. This is done with fluid pressure and by the use of a drill fluid that will permit partial or complete loss of returns to the formation during placement. This technique was first intentionally used by Gulf in May, 1950, and since that time has been applied in more than 90 wells. Other advantages claimed for this type of completion are that the pressure placement of the gravel has a scouring effect on the casing perforations, that additional drainage channels to the well bore are created, and that the possibility of shifting of the formations adjacent to the casing is minimized and possibly prevented. During the past few years, the use of gravel to prevent or retard the migration of unconsolidated sands into the well bore has met with a favorable degree of success. Numerous methods and techniques of "gravel packing" have been used, each having its own relative merits, and with varying results. M. L. Cashion1 in 1939 ably reviewed the history of gravel packing to that time. As stated in his paper, ". .. the idea of gravel packing wells is not new." During the period 1939 to 1949, very little if any progress or change in technique in this type of completion was made. However, it was noted in some cases that during the placement of gravel, if there was a loss of drill fluid to the formation, there was a corresponding loss of gravel to the formation. Also, it was noted that in those gravel-packed completions (opposite casing perforations) that "sanded up," there was found to be an absence of gravel in the annular space between the liner and casing, although gravel had previously been placed in this space and no gravel had been removed from the well at the surface. These findings resulted in the placement of gravel with fluid pressure and by the use of a drill fluid that would permit partial or complete loss of returns to the formation during placement. Pressure placement of gravel became an accepted practice in late 1949 and early 1950. Another fact brought to light that has contributed to the current success of gravel pack completions is that drilling fluids containing solids will to some extent cause plugging of the screening medium or blocking of the producing section. The removal of these solids by chemical action, mechanical action, or a combination of the

Jan 1, 1955

By F. S. McNicholas, R. L. Healy

NOTEWORTHY because of the amount of explosives used, the tonnage broken, and the wide range involved both vertically and laterally, was a large underground blast fired last November at the Hidden Creek mine, Anyox, B. C. Stoping methods and mining prac¬tices at the Hidden Creek mine have previously been described in the technical press. Earlier mining methods employed included shrinkage stoping, glory-holing, and "spiral" stoping. The latter especially has been a practice peculiar to the Granby company, having been used for years at its Phoenix mines and later at the Anyox property where conditions as to size of orebodies and strength of ground both in the ore and walls were similar. These methods all leave tremendous excavations supported at key points by pillars and braces that may only be safely mined by big blasts.

Jan 1, 1935

By Leonard B. Lipson

Boyer, Morgan and Muskat,&apos; with improvements by Morgan, McDowell, and Doty,l and Laird and Putnam,&apos; have described a scheme for the determination of fluid saturatic in porous media by measuring the x-ray linear absorbing power of particular fluids in the media. This method is one of several which depend on the linear absorbing power of the fluids in the porous medium. Other examples of linear absorption methods involve measurement of dielectric constant, gamma ray absorption, and ultrasonic attenuation. It is the purpose of this note to demonstrate by theortical considerations that the absorption versus saturation curve for a linear absorption method is not necessarily a single valued function of the saturation. Such non-unique behavior must be considered and evaluated before suitable saturation determinations can be made by a linear absorption method. To illustrate the discussion, examples will be given only for the simplest cases of combinations of two different dielectrics. The dielectric constant method was chosen for illustration because it was thought to demonstrate most graphically the point in question. According to Argue and Maass,4 the resultant dielectric constant of a combination of two different dielectrics depends on the orientation of the dielectrics in the electric field of the test condenser used to measure the dielectric constant. One ease involves alternate slabs of dielectrics E1 and E2 perpendicular to the electric field of the test condenser, as shown in Fig. 1A. For this case: l/&apos;E, = A/E, + B/E,.......(1) where E,,, is the dielectric constant of the combination, A is the ratio of the path length through dielectric E, to the distance between the plates of the condenser (assuming the dielectrics have the same cross sectional area as the condenser), and B is the ratio of the path length through dielectric E2 to the distance between the plates of the condenser. It will be noted that the constants A and B are numerically equal to the fractional "saturation" of the region between the test plates of the condenser by the two dielectrics E1 and E2, respectively. Another case involves alternate columns of the two dielectrics parallel to the electric field and forming a continuous path between the condenser plates, as shown in Fig. 1B. For this case: E., = AE1 + BE2.........(2) where E., is the dielectric constant of the combination, A is the ratio of the cross sectional area of dielectric E, to the cross sectional area of the condenser plates (assuming the lengths of the dielectrics equal the distance between the condenser plates) and B is the ratio of the cross sectional area of dielectric E2 to the cross sectional area of the condenser plates. As before the constants A and B are the effective "saturation" of the condenser by the two dielectrics. Still another case is described by Lichtenecker5 where dielectric E2 is shown in the form of small particles distributed at random in dielectric E1. This is shown in Fig. 1C. For this case: log Em = A log E1 + B log E2.....(3) where Em is the dielectric constant of the combination. A is the ratio of the volume of dielectric E1 to the volume of the condenser, i.e., the effective "saturation" of the condenser by dielectric E,. B is the ratio of the volume of dielectric E2 to the volume of the condenser, i.e., "saturation" of dielectric El. Equations (l), (2) and (3) are plotted in Fig. 2 for E1 = 2.5 (oil) and E2 = 80 (water). Equations (1) and (2) may he thought of as representing the limiting cases of the configuration of two fluids which might be expected to exist in a porous medium. Equation (3),

Jan 1, 1951

By Leonard B. Lipson

Boyer, Morgan and Muskat,&apos; with improvements by Morgan, McDowell, and Doty,l and Laird and Putnam,&apos; have described a scheme for the determination of fluid saturatic in porous media by measuring the x-ray linear absorbing power of particular fluids in the media. This method is one of several which depend on the linear absorbing power of the fluids in the porous medium. Other examples of linear absorption methods involve measurement of dielectric constant, gamma ray absorption, and ultrasonic attenuation. It is the purpose of this note to demonstrate by theortical considerations that the absorption versus saturation curve for a linear absorption method is not necessarily a single valued function of the saturation. Such non-unique behavior must be considered and evaluated before suitable saturation determinations can be made by a linear absorption method. To illustrate the discussion, examples will be given only for the simplest cases of combinations of two different dielectrics. The dielectric constant method was chosen for illustration because it was thought to demonstrate most graphically the point in question. According to Argue and Maass,4 the resultant dielectric constant of a combination of two different dielectrics depends on the orientation of the dielectrics in the electric field of the test condenser used to measure the dielectric constant. One ease involves alternate slabs of dielectrics E1 and E2 perpendicular to the electric field of the test condenser, as shown in Fig. 1A. For this case: l/&apos;E, = A/E, + B/E,.......(1) where E,,, is the dielectric constant of the combination, A is the ratio of the path length through dielectric E, to the distance between the plates of the condenser (assuming the dielectrics have the same cross sectional area as the condenser), and B is the ratio of the path length through dielectric E2 to the distance between the plates of the condenser. It will be noted that the constants A and B are numerically equal to the fractional "saturation" of the region between the test plates of the condenser by the two dielectrics E1 and E2, respectively. Another case involves alternate columns of the two dielectrics parallel to the electric field and forming a continuous path between the condenser plates, as shown in Fig. 1B. For this case: E., = AE1 + BE2.........(2) where E., is the dielectric constant of the combination, A is the ratio of the cross sectional area of dielectric E, to the cross sectional area of the condenser plates (assuming the lengths of the dielectrics equal the distance between the condenser plates) and B is the ratio of the cross sectional area of dielectric E2 to the cross sectional area of the condenser plates. As before the constants A and B are the effective "saturation" of the condenser by the two dielectrics. Still another case is described by Lichtenecker5 where dielectric E2 is shown in the form of small particles distributed at random in dielectric E1. This is shown in Fig. 1C. For this case: log Em = A log E1 + B log E2.....(3) where Em is the dielectric constant of the combination. A is the ratio of the volume of dielectric E1 to the volume of the condenser, i.e., the effective "saturation" of the condenser by dielectric E,. B is the ratio of the volume of dielectric E2 to the volume of the condenser, i.e., "saturation" of dielectric El. Equations (l), (2) and (3) are plotted in Fig. 2 for E1 = 2.5 (oil) and E2 = 80 (water). Equations (1) and (2) may he thought of as representing the limiting cases of the configuration of two fluids which might be expected to exist in a porous medium. Equation (3),

Jan 1, 1951

The following is an incomplete list of members and guests who. called at Institute headquarters during the period Dec. 10, 1917 to Jan. 10, , 1918: A. A. Arluck, Camp Merritt, N. J. W. Spencer Hutchinson, Boston, Mass. C. L. Bruns, Santiago de Cuba. William F. Jahn, New York, N. Y. Henry C. Carr, New York, N. Y. C. H. James, Tucson, Ariz. L. J. Charles, Santa Fe, N. M. Charles Janin, San Francisco, Cal. W. A. Deane, Waxhaw, N. C. Joseph T. Kupferstein, Shreveport, Pa. P. St. John Dixon, Rio de Janeiro, Brazil. Richard Lamb, New York, N. Y. M. C. Drake, Marquette, Mich. Walter R. Malm, San Francisco, Cal. F. W. Draper, Petrograd, Russia. W. H. Nash, Buffalo, N. Y. Paul W. Gaebelein, Boise, Idaho. Edmund Newton, Minneapolis, Minn. H. F. E. Gamm, Rutherford, N. J. Guy C. Riddell, Port Pirie, South Australia. C. A. Grabill, El Paso, Tex. Williams A. Simkins, San Francisco, Cal. William H. Hampton, New York, N. Y. Henry B. Smith, Northampton, Mass. R. M. Henderson, Brackenridge, Colo. H. E. Smith, Chicago, Ill. Geo. B. Holderer, Northpines, Ont., H: C. Spaulding, Washington, D. C. Canada. Y. Wakabayashi, Tokyo, Japan. H. H. Howry, Camp Upton. N. Y. A. P. Watt, Mine La Motte, Mo. L. Douglas Anderson", superintendent of the Midvale, Utah, smeltery of the United States Smelting Co., has been appointed manager of smelteries for the company at Salt Lake City, Utah.

Jan 2, 1918