Search Documents

By A. M. Nicholas

WheN attempting to lift mill pulp containing a considerable percentage of wolframite, in an ordinary bucket elevator, difficulty was encountered from the tendency of the tungsten minerals to settle, on account of their high specific gravity. Lifts not exceeding 20 ft. (6 m.) could be accomplished without particular difficulty, because there was insufficient time for consolidation of the heavy minerals in the bottom of the bucket; but with higher lifts, the heavy tungsten minerals would settle so solidly that when the bucket turned over at the top of the elevator the contents could be only partially dumped. In this case it was necessary to lift the material a distance of 34 ft. (10m.); hence some means had to be adopted to prevent settling, at least to such an extent that the material could be dumped from the buckets. To reduce the carrying time to a sufficient extent would have required a belt speed of 475 ft. (144.7 m.) per minute, which was not feasible. It was decided to try, by vibrating the belt about midway of its span, to keep the material sufficiently agitated during elevation to prevent settling. Underneath the rising side of the belt was placed a 12-in. (30.48-cm.) idler pulley, 18 ft. (5.5 m.) up in the total lift of 34 ft. The idler pulley was set eccentric by % in. (19 mm.) and it was hoped that the vibration thus imparted to the belt, running at a speed of 280 ft. (85 m.) per minute, would prevent settling in the buckets. It was found that the pressure of the belt on the idler, due to the small inclination of the elevator, was not sufficient to overcome sliding on the idler, and the agitation was insufficient to accomplish the desired purpose. The idler was then connected to the drive shaft of the elevator through an intermediate pulley, gearing down to a speed of 20 r.p.m., so that a positive vibration was imparted to the belt; this imparted enough motion to the belt to prevent settling and the contents of buckets dumped satisfactorily. Protecting Elevator Belts When elevating, from the crusher, a rock which was very sharp and abrasive, considerable difficulty arose from cutting of the belt under-

Jan 1, 1918

Apart from the general cooperation received in many quarters, the Unitization Committee desires to make specific acknowledgment to the following individuals for assistance rendered in the study to this time. California.—Committee members: Joseph Jensen, chairman, L. L. Brundred, E. M. Butterworth, H. Norton Johnson, D. B. Myers, W. R. Wardner; others who contributed: C. R. McCollom, F. C. Merritt, E. B. Noble, Ralph Arnold, J. R. Pemberton, Roy R. Morse, T. F. Stipp, John R. Roberts, R. D. Bush, Alexander Anderson, J. A. Taff, F. 0. Martin, J. E. Van Gundy, E. K. Parks, A. C. Rubel, Lew Suverkrop, W. L. McLaine, Gerard Henny, Walter Stalder, Lester C. Uren, Hoyt S. Gale, W. L. Walker. Rocky Mountain.—Fred E. Wood, chairman, J. G. Bartram, C. E. Dobbin, Wilson B. Emery, Charles E. Erdman, R. D. Hawley, E. W. Krampert, Foster Morrell, W. T. Nightingale, K. B. Nowels, C. M. Rath, Earl Shoenfelt, J. W. Steele, E. T. Wilson, J. J. Zorichak. Kansas-Oklahoma.—Committee members: C. E. Beecher, chairman, A. W. Ambrose, R. C. Hauber, Clyde Alexander, R. F. MacArthur, C. R. Swarts, M. M. Valerius, E. H. Griswold, G. 6. Rollin, L. Murray Newman, David L. Trax, Richard K. Huey, Marvin Lee, Harry Johnson; others who contributed: E. A. Carr, Paul S. Ache, K. C. Slater, R. S. McFarland, J. R. McWilliams, Joseph Chalmers, Henry A. Ley, Dorsey IIager, H. C. George, W. K. Whiteford, L. G. E. Bignell, L. E. Smith, George E. Burton. Texas, Louisiana, Arkansas, New Mexico.—Frederic H. Lahee, chairman, Donald C. Barton, C:. E. Beecher, Olin G. Bell, G. E. Campbell, Paul Wagner, John West, Robin Willis, J. M. Forgotson, E. J. Gorman, P. S. Haury, Marvin Lee, C. F. Lytle, L. H. McBee, T. F. Petty, C. C. Pope, F. S. Prout, J. C. Stewart, J. R. Suman, L. P. Teas, W. C. Thompson, A. F. Truex, R. B. Campbell, M. G. Cheney, P. C. Dean, F. W. DeWolf, Dugald Gordon, B. A. Hardey, F. E. Heath, J. F. Lucey, George C. Matson, W. H. Perot, T. W. Pew, W. A. Price, W. A. -Reiter, R. C. Stewart. Eastern United States and Foreign Fields.—H. H. Hill and E. L. Estabrook, chairmen; Dr. Richard Ambronn, Gottingen, Germany; Arthur R. Andrew,

Jan 1, 1930

By AIME AIME

THE annual fall meeting of the Institute of Metals and the Iron and Steel divisions, in conjunction with the American .Society for Steel Treating and the Metal Congress and Show, at Boston was from many standpoints the most successful we have had to date. While many faces were missing from the various gatherings, the Institute registration reached the high mark of 324 members and guests. Cooperating with the Steel Treaters were also the American Society of Mechanical Engineers, the Society of Automotive Engineers and the American Welding Society. ,The meeting was, as usual, a three-ring circus with technical sessions 'galore, plant .trips, visits to the Exposition, social events such as lunch- eons and dinners as well as entertainment for the ladies present.

Jan 1, 1931

All the TECHNICAL PUBLICATIONS and CONTRIBUTIONS published in 1940 are available at Institute headquarters, unless otherwise noted. They are also on file in many public, university and technical libraries and, when so indicated in the list, may be found in the TRANSACTIONS. TECHNICAL PUBLICATIONS in Classes A-Metal Mining, B-Milling and Concen-tration, H-Industrial Minerals, and I-Mining Geology are distributed in MINING TECHNOLOGY, which is issued every other month. Technical Publications in Classes C-Iron and Steel Division, D-Nonferrous Metallurgy and E-Institute of Metals Division are distributed in METALS TECHNOLOGY, which is issued twice quarterly. TECHNICAL PUBLICATIONS in Class G-Petroleum Division are distributed in PETRO-LEUM TECHNOLOGY, which was issued quarterly in 1940 but will be issued every other month in 1941. TECHNICAL PUBLICATIONS in Classes F-Coal Division, J-Mineral Industry Education Division, K-Mining Administration, and L-Geophysical Methods of Exploration are issued as separate pamphlets. An Institute member is entitled to one copy of any TECHNICAL PUBLICATION or CONTRIBUTION. Copies of TECHNICAL PUBLICATIONS listed have been mailed to members of the Institute accord-ing to their registration by classes. CONTRIBUTIONS and other TECHNICAL PUBLICA-TIONS will be sent upon request. A member may purchase an additional copy of a TECHNICAL PUBLICATION or a CONTRIBUTION at one cent a page; minimum charge, 25¢. Nonmembers may purchase any CONTRIBUTION or a TECHNICAL PUBLICATION of the F, J, K, or L classes at the same rate, but the nonmember price per copy for METALS TECHNOLOGY, MINING TECHNOLOGY or PETROLEUM TECHNOLOGY is $1.25 domestic, $1.35 foreign countries. TECHNICAL PUBLICATIONS (separate pamphlet form), $2 per annum domestic, $2.50 foreign. METALS TECHNOLOGY, $7 per annum domestic, $7.80 foreign (Iron and Steel Division and Institute of Metals Division ferrous and nonferrous papers). MINING TECHNOLOGY, $6 per annum domestic, $6.60 foreign (metal mining, milling and concentration, Industrial Minerals Divi-sion, and mining geology papers.) PETROLEUM TECHNOLOGY, $6 per annum domestic, $6.60 foreign. Bound volumes have been mailed to members that have requested them, and MINING and METALLURGY is mailed each month. A member is entitled to one volume a year on his membership and he may purchase for $2.50 one copy of a volume not already received; additional copies of the same volume, $5. Nonmembers may pur-chase the volumes listed, at $5 each, plus 60 cents for Canadian or foreign postage. Extra single copies of MINING AND METALLURGY, 25¢ current issue, back numbers 50¢ each to members; to nonmembers 506 current issue and $1 each, back issues. Subscription price to nonmembers and to members for extra copies, $3 per annum domestic, $4.00 foreign.

Jan 1, 1940

By H. F. A. Hergt, K. L. Sutherland, J. Rogers

In 1938 Ralston4 reviewed the many attempts to find a satisfactory collector for the separation of cassiterite from its ores and in 1944 Dean and Ambrose2 summarized some further attempts. Generally, soaps and amines are effective but nonselective collectors. We have discovered that reagents containing either the polar group — SO4- or — SO3- are excellent collectors for cassiterite and promise to be selective. The response to these reagents of cassiterite and of minerals commonly associated with it was studied, using the captive-bubble technique. Using these fundamental data, the practicability of separation and concentration of tin was investigated by flotation tests in a 2000-gram Denver cell. Experimental Methods Reagents All inorganic reagents were of Analar grade. The preparation and purification of sodium cetyl sulphate, cetyl trimethyl-ammonium bromide, laurylamine and cetylamine have been previously described.5 The other collectors were commercial surface-active agents, which were used without purification. Tests Captive-bubble Tests and Cylinder Flotation Tests have been previously de- scribed.5,10 The full lines shown in the figures relating solution composition to contact (flotation) distinguish solutions in which contact (flotation) is possible from those in which it is not. The curve is derived by successive approximation and the accuracy is ±0.2 pH units and ± 5 mg. per liter of collector or depressant. Solution compositions for which it was shown experimentally that contact or flotation is possible are marked by a circle, those for which it is not possible, by a cross, and those for which it is doubtful by a cross within a circle. It is assumed that at all other solution compositions within (without) the curve, contact or flotation is possible (not possible). After testing in the collector solution, the mineral was removed, washed, and tested by the captive-bubble method in water, or floated in a cylinder with frother only. In this way the composition of solutions in which a mineral was conditioned but in which properties of the collector solution prevented contact or flotation can be defined. The composition of solutions in which conditioning was possible lie between the full and broken curve, and the experimental results are indicated by a square. The curves show the limits of composition of solutions in which flotation in a cell would be possible but many factors other than those considered in these the determine recovery and grade of a given mineral in practice. Flotation Tests in 500 and 2000-gram Denver SUbmachines,—Melboume tap water, containing 12 parts calcium, 6 parts

Jan 1, 1947

By J. Rogers, H. F. A. Hergt, K. L. Sutherland

In 1938 Ralston4 reviewed the many attempts to find a satisfactory collector for the separation of cassiterite from its ores and in 1944 Dean and Ambrose2 summarized some further attempts. Generally, soaps and amines are effective but nonselective collectors. We have discovered that reagents containing either the polar group — SO4- or — SO3- are excellent collectors for cassiterite and promise to be selective. The response to these reagents of cassiterite and of minerals commonly associated with it was studied, using the captive-bubble technique. Using these fundamental data, the practicability of separation and concentration of tin was investigated by flotation tests in a 2000-gram Denver cell. Experimental Methods Reagents All inorganic reagents were of Analar grade. The preparation and purification of sodium cetyl sulphate, cetyl trimethyl-ammonium bromide, laurylamine and cetylamine have been previously described.5 The other collectors were commercial surface-active agents, which were used without purification. Tests Captive-bubble Tests and Cylinder Flotation Tests have been previously de- scribed.5,10 The full lines shown in the figures relating solution composition to contact (flotation) distinguish solutions in which contact (flotation) is possible from those in which it is not. The curve is derived by successive approximation and the accuracy is ±0.2 pH units and ± 5 mg. per liter of collector or depressant. Solution compositions for which it was shown experimentally that contact or flotation is possible are marked by a circle, those for which it is not possible, by a cross, and those for which it is doubtful by a cross within a circle. It is assumed that at all other solution compositions within (without) the curve, contact or flotation is possible (not possible). After testing in the collector solution, the mineral was removed, washed, and tested by the captive-bubble method in water, or floated in a cylinder with frother only. In this way the composition of solutions in which a mineral was conditioned but in which properties of the collector solution prevented contact or flotation can be defined. The composition of solutions in which conditioning was possible lie between the full and broken curve, and the experimental results are indicated by a square. The curves show the limits of composition of solutions in which flotation in a cell would be possible but many factors other than those considered in these the determine recovery and grade of a given mineral in practice. Flotation Tests in 500 and 2000-gram Denver SUbmachines,—Melboume tap water, containing 12 parts calcium, 6 parts

Jan 1, 1947

By G. E. McElroy

MUCH attention has been directed to mine-air flow in recent years, more especially in Great Britian where there is frequent reference to a theory of fluid flow developed by English engineers. Briefly stated, this theory is that for similar passages of the same relative roughness, in which fluid flow occurs, the conditions of flow are exactly the same for equal values of the product W D V, where W = density of the fluid, D = diameter of the passage through which flow occurs, V = mean velocity of flow, and m = absolute viscosity of the fluid flowing. This, the "Reynolds Criterion" of fluid flow, had its origin in the work of Prof. Osborne Reynolds' more than 40 years ago. Later, Lord Rayleigh amplified the theory2 which has been conclusively proved for small pipes by the experiments of Stanton and Pannel3 over a large flow range, and by Lacey4 over a somewhat more limited range. Concordant results on small pipes have also been obtained by numerous other investigators with single fluids over more or less limited ranges of flow. According to this theory results in one medium, such as water, are immediately applicable to another, such as air; and experimental results on models are (theoretically, at least) applicable to full-scale designs. This is of great importance in aeronautics and can be of considerable value in mine ventilation research. Hodgson, in a recent paper,5 has outlined the application of this theory to mine-air flow and recent English experiments' on the resistance of a timbered mine airway have been expressed in this form.

Jan 10, 1926

B. S. Crocker (Screened Ore Used for Fine Grinding at Lake Shore Mines, P. 499) was born in Toronto, Ont. and attended Saint Andrews College and University of Toronto. He received a B.A. and M.A. degree. He was graduated with honors and received a fellowship in metallurgy. Mr. Crocker did post-graduate research at University of Toronto from 1933 to 1934. He was employed by Beattie Gold Mines in 1933. He did research in milling at Lake Shore Mines from 1934 to 1936 and from 1936 to 1940 was head of experiment laboratory. At the present time he is mill superintendent with Lake Shore Mines at Kirkland Lake, Ont., Canada. Grinding, cyanidation, flotation and roasting are of special interest to him. He is a member of AIME. Mr. Crocker has presented several papers before C.I.M.M. and also holds membership in this society as well as Professional Engineers of Ontario. Skiing, yacht racing and photography are his favorite hobbies.

Jan 1, 1952

By M. H. Caron

D. C. Ralston—The fact that none of the organizations that have worked on these ammoniacal leaching processes have contributed discussion of Mr. Caron's papers today is a matter of some disappointment. Adaptations, modifications and improvements have been made by several organizations or individuals and to complete the record I want to document a number of them. The Nicaro Nickel Co. operated a Government owned plant at Nicaro, Oriente, Cuba, during the past war. A report on the project was written for Reconstruction Finance Corp. and is in the document file collected by the Office of Technical Services, Commerce Department and filed with the Library of Congress, where it can be consulted or bibliofilm or photostat copies obtained by asking for copies of PB 97271. Nicaro Nickel Co. has obtained a series of U.S. Patents, my list (probably incomplete) of which bears the following numbers: 2,400,098; 2,400,114; 2,400,115; 2,400,461; 2,400,612; 2,458,902 and 2,473,795. International Nickel Co. has also studied the problem and U.S. Patent 2,478,942 shows that some of the complications involving occasional low extractions have been unraveled. Forward, Samis, and Kudryk, of the University of British Columbia, have also published a study of copper-nickel sulphide concentrate.' Others are interested and it is evident that this type of hydrometallurgy is likely to find a happy application in the not-too-far distant future. Caron's two papers practically amount to a summation of his life's work on the important subject of nickeliferous iron ores and the American Institute of Mining and Metallurgical Engineers is fortunate to have been chosen the medium of publication. M. Rey—The ammonia leaching process has been the subject of certain studies in New Caledonia, but at the present time, the conditions are not very favorable to its adoption. The process is a combination of a thermal and a hydrometallurgical process. As a result, the first costs and the operative costs are rather high. To counteract this unfavorable situation, it would be necessary to make a very high extraction. But unfortunately, the process is delicate and in spite of all of Caron's valuable work, there are still many unknown factors. It is difficult to obtain regularly a high extraction, exceeding 75 to 80 pct. It would be interesting to have the opinion of Inter-national Nickel on the process and to know what the Dutch are doing in Celebes. M. H. Caron (author's reply)—I am quite familiar with the different types of nickel and cobalt ores as found on New Caledonia, and it may be pointed out that the Celebes ores are quite the same in their properties. Their behavior when treating the ores by the ammonia-leaching process is also alike and in my opinion, there is no reason why a high extraction of the New Caledonian ores could not be obtained if the process is properly applied. For the sake of completeness I may add that one of my patents has not been discussed in the papers. This patent deals particularly with the treatment of serpentine nickel ores. (Netherlands No. 62693 40a, French No. 965.786 April 21. 1948. and Cuban No. 13.625 Jan. 1950.) O F. A. Forward, C. S. Samis, and V. Kudryk: Trans. Canadian Institute of Mining and Metallurgy. (1948) 151 (Bull. 434) 350-355.

Jan 1, 1951

By H. N. Wolcott

AMONG the many cases of replacement of one mineral by another, that of quartz or silicates by pyrite, or even other sulphides, is not uncommon, but the reverse of this process does not appear to have been recorded, even if it has been observed. It, therefore, seemed to the writer that the case described below was worthy of record. FIG. I.-GROUND MASS OF CHALCOPYRITE (C) CONTAINING ROUNDED GRAINS OF PYRITE (P) SHOWING DIFFERENT DEGREES OF REPLACEMENT BY QUARTZ (Q), AND ALSO QUARTZ VEINLETS CUTTING THROUGH THE PYRITE. (PHOTOGRAPHED BY REFLECTED LIGHT.) The specimens described in this paper were obtained by R. B. Morton of Idaho Springs, Colo., from the Old Town Mine, in Russell Gulch, and are in the collection of Cornell University, where the writer studied them. In the rough, the specimens appeared to consist largely of chalcopy- rite, with some grains of tetrahedrite. The polished surface of some of

Jan 6, 1917

By J. C. Irvine

Meramec Mining Co. has put into operation a crushing and conveying system on its newly established 2475-ft level, 200 ft below the lowest production. To develop this level without interrupting hoisting or mine haulage, a 15.8% decline was driven from the 2275-ft level. A 5-cu-yd LHD diesel loader and a diesel-powered drilling jumbo were put into operation midway down the decline, and were used to develop the remainder of the decline and the entire level. Development of the ore pass system to the crusher required the construction of Swedish-type dumps on the main haulage-ways of all production levels with a minimum disruption of ore haulage. Concrete was handled by both rail-mounted and rubber-tired vehicles. The system features four Swedish-type dumps with control chutes at the lower three dumps, a 42-in. gyratory crusher with attendant feeders, and an 1800-ft long roof suspended conveyor feeding two 5000-ton ore bins. The crushed ore from these bins is conveyed to the lower of the mine's two original loading stations for hoisting. The retention of the original dumping and ore pass system as an alternate route has given mine production a unique flexibility. Operation for 22 months has permitted evaluation of the system from a long-term standpoint.

Jan 1, 1973

By Robert Linton

AT its meeting on May 21, the Board of Directors approved the recommendations submitted by President Lovejoy and named a nominating committee for the year that is especially well distributed as to major technical interest and as to geography. As may be seen from the list published herewith, two come from the East, two from the Midwest, and three from the far West. Mr. Linton, the chairman, has been a valued member of the Institute for 36 years. A memorandum drawn up by Paul D. Merica, representing the A.I.M.E., and W. R. Barclay, representing The Institute of Metals of Great Britain, setting forth a reciprocal plan for special memberships in each Institute for members of the other, was discussed. Both societies already have formally approved the plan in principle and Dr. Merica was clothed with full authority to agree on a few small details that have not been settled, and conclude the arrangement in behalf of the Institute.

Jan 1, 1936

New York Meets first Wednesday after first Tuesday of each month. DAVID H.-BROWNE, Chairman, JOHN H. JANEWAY, Vice-Chairman. F. E. PIERCE, Secretary, 35 Nassau St., New York, N. Y. P. A. MOSMAN, Treasurer. LEWIS W. FRANCIS. Boston Meets first Monday of each winter month. HENRY L. SMYTH, Chairman. . ALFRED C. LANE, Vice-Chairman. HENRY A. WENTWORTH, Secretary-Treasurer, 60 India St., Boston, Mass. ROBERT H. RICHARDS, ALBERT SAUVEUR. Columbia Holds four sessions during year. Annual meeting in September or October. FRANK A. ROSS, Chairman. RUSH J. WHITE, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P O. Drawer 2154, Spokane, Wash. FREDERIC KEFFER, FRANCIS A. THOMSON.

Jan 11, 1915

By R. S. Dean

THE commercial production of electrolytic manganese on a small scale commenced in 1939. The writer made a short report on the progress of production and utilization in MINING AND METALLURGY for January 1941. Progress during the last two years, naturally, has been more rapid. In June 1940, Congressman (now Senator) Scrugham presented a proposal to Congress for an appropriation authorizing erection of a pilot plant for "the production of metallic manganese by electrolytic or other means." As a result of this, a pilot plant, having a capacity of a few hundred pounds per day was built at Boulder City, Nev. Subsequent appropriations permitted expansion of the plant to about a ton per day. Much has been learned in this plant about electrolytic manganese, and the product even in its small way has found war uses of considerable importance. Meanwhile, the Knoxville plant of the Electro Manganese Corporation, the sole commercial producer, was expanded to about 4 tons per day to supply needed material for the war program. Other proposals for commercial plants have not been favorably received by the War Production Board. The Bureau reported on one such proposal by the American Alloys and Chemical Corporation. PRACTICE AT BOULDER CITY The present practice, as carried out at Boulder City, which is being described in more detail in a current paper by the Bureau staff at Boulder City, starts with a manganese dioxide ore containing about 20 per cent manganese. Currently this ore comes from the Three Kids deposit near Las Vegas. The steps for the production of electrolytic manganese, in general, are as follows: I. The manganese in the ore is reduced to MnO. 2. The MnO is dissolved from the ore in spent electrolyte, which contains about 38 to 47 grams per liter of free sulphuric acid, 135 grams per liter of ammonium sulphate, and 10 to 12 grams per liter of Mn as sulphate. In the leaching step the manganese is built back up to 32 to 36 grams per liter of Mn as sulphate; the pH is adjusted to neutral by means of gaseous ammonia and passed through thickeners. 3. The electrolyte is purified by adding H2S, which precipitates the heavy metals. After filtering, ferrous sulphate is added to the solution and oxidized with air and the solution is filtered and clarified on a precoat filter. 4. The purified catholyte is electrolyzed in a diaphragm cell using stainless-steel cathodes and lead-silver anodes. The current density is about 45 amp. per sq. ft. Current efficiencies of 60 to 65 per cent are regularly obtained.

Jan 1, 1944

By Benjamin Lustman, Robert F. Mehl

THE study of the high-temperature oxidation of pure metals, intensively pursued experimentally since the pioneer work of Pilling and Bedworth1 and supplemented by the recent theoretical work of Wagner2 is now well advanced. The important field of low-temperature oxidation-i.e., oxidation extending only through the temper color range of thicknesses with the formation of thin oxide layers in the range from o to 1000-2000 Angstroms-has not, however, reached so satisfactory a state, owing largely to the experimental difficulties that attend the formation and study of thin films; most of the work has been performed on abraded specimens whose surface irregularities approximated the thickness of the films formed. It has been pointed out that the rates of oxidation of different crystal faces are different and that the difference may be related to the orientation relationships that obtain between the metal crystal and the superimposed oxide crystal; it has also been suggested that this orientation dependence should manifest itself in rates of oxidation and perhaps also of corrosion in aggregates bearing preferred orientations. 3,4 An attempt to measure the rates of oxidation of different crystal faces of alpha iron demonstrated this difference in rate,4 but the dependence of rate on orientation was not simple; the method of measuring thickness, consisting of a color comparison with barium stearate multi-films of known thickness, was not wholly satisfactory. For these reasons it was felt that a study of the rate of oxidation of single crystals prepared with surfaces as smooth as possible, using a sensitive method giving true film thickness, should be profitable. Copper was chosen because of the ease of reduction of the primary oxide film and because the orientation relationships between metal and oxide and the composition of the oxide films formed at low temperatures are known; for thin films formed at low temperatures, Cu2O alone occurs.22-24 EXPERIMENTAL PROCEDURE Various methods of surface preparation were attempted in order to obtain a surface that would oxidize uniformly and reproducibly. Electrolytic polishing by the method of Jacquet5 and electrolytic and mechanical polishing followed by annealing in vacuum and in purified hydrogen at various temperatures were tested. The procedure finally adopted consisted in a fine metallographic polish followed by an anneal in purified hydrogen at temperatures of 900º to 1000°C. for 12 hr. or more. The surface so produced was very bright and smooth, with no trace of specular etching (though some grain-boundary etching was observed); indeed, fine scratches produced by the final polish were entirely removed by the high-temperature anneal.

Jan 1, 1941

By D. F. Kaufman, E. D. Levine, L. R. Aronin

The deformation of' impure beryllium crystals by basal glide at room temperature invariably tevminates by basal cleavage after a few percent strain. It is generally accepted that .fracture of this type is caused by the splitting of low) -angle boundaries, or bend planes, by obstacles that restrict the motion of the bed planes in the deforming crystal. The details of such a process have been developed by Stroh, who showed that the high tensile stress norrnal to the basal plane in the region where the bend plane is split results in the propagation of a basal cleavage crack, provided there is no available dejorvrlatzon mode having a shear component normal to the basal plane It has been postulated that puvification of beryllium might lead to increased basal ductility by the vemoval of barviers to bend plane motion and possibly by the activation of nonbasal defor~rlation systems. Large increases in the amount of basal glide that can he sustained prior to fracture have been observed in crystals purified by zone refining. In each case, eventudal fracture was by sharp basal cleavage, suggesting that the split bend plane model still applies to tile fracture of beryllium of rensonably high purity. In the present work, calculations are made to show to what extent basal duetilits can be increased by purification while the split bend plane .fracture process remains applicable. Experimentally observed ductilities are generally somewhat lower than those predicted by calculation because of premature failure due to defects introd~cced during specimen preparation and testing. SEVERAL investigators1-4 have studied the deformation characteristics of beryllium single crystals of commercial purity, and have related the strong anisotropy of plastic deformation in single crystals to the problem of brittleness in polycrystalline beryllium. For most orientations, the principal deformation mode is basal slip, which, at temperatures between 300" and 900°K, begins at a critical resolved shear stress of approximately 1500 g per sq mm and terminates after 3 to 6 pet glide strain by cleavage on the basal plane in the neighborhood of (1120) bend planes that are formed during the deformation. This type of fracture, which is also observed in zinc at low temperatures, has been interpreted by stroh5 to be caused by the splitting of bend planes by obstacles to their motion. In the Stroh model, a (11.20) dislocation wall, or bend plane, moving along the slip direction under the action of the applied stress, encounters obstacles which cause part of the bend plane to be held up, the other part continuing to move. Stress concentrations are built up in the region where the bend plane is split, with a high tensile component normal to the basal plane, resulting in a microcrack at the end of the split wall. Because no deformation mode having a shear component at an angle to the basal plane is available to relieve the stress at the crack tip, the crack can propagate under a sufficiently high applied stress. The Stroh criterion for crack propagation is given by

Jan 1, 1964

By Carl F. Floe, Michael B. Bever

THE possibility that carbon may be soluble in copper to a limited extent has been recognized for over a century. The quantitative investigation of this problem, however, requires more sensitive techniques than have formerly been available. Three recent developments have made possible more accurate determinations: the vacuum-fusion method of analysis, the production of copper of high purity and the availability of high-purity refractories, particularly graphite. In addition to its obvious theoretical interest, the problem of carbon solubility in copper is of practical importance. In the production of copper and of high-copper alloys, carbonaceous covers are frequently used. If even minute amounts of carbon are dissolved, insoluble carbon oxide gases will be formed when such metals are poured under oxidizing conditions. A mechanism of this kind could well be one of the principal causes of gas porosity in casting copper-base products. REVIEW OF LITERATURE In 1823 Vivian1 raised the question as to whether copper by overpoling becomes "combined with a minute portion of carbon." Karsten2 asserted, in 1832, that carbon reduces the high-temperature strength of pure copper, so that when the carbon content has reached 0.2 per cent the metal will be brittle at a dark red heat. According to Karsten, carbon contents of o.05 per cent make it difficult to hot-work copper. He also reported that the specific gravity of copper is 8.8969 and that it increases to 8.92 58 if the copper is cemented with carbon and then melted. He emphasized the difficulty of determining analytically the small amounts of carbon present in copper. The metal was removed by wet methods and the residue considered as carbon. At Percy's request, Dick,3 in 1856, carried out various working tests on copper that had been in prolonged contact with carbon, and found that the working properties of the metal had not been affected. He also attempted to determine the presence of carbon analytically. In one experiment the copper was dissolved and the residue was fused with litharge, and in another essentially a combustion analysis was made on a copper sample. In a final experiment, a sample was dissolved and the residue subsequently subjected to a combustion analysis. Indications of as much as o.005 per cent carbon were found, but Dick considered his work inconclusive largely because of the possible interference of sulphur. Percy4 concluded, from Dick's experiments and from some experimental work of his own, that the solubility of carbon in copper had not been established with

Jan 1, 1945

By L. W. Rowe, W. R. Opie

A brief history of TiCI, production and purification is given. Chlorinator feed materials for the production of TiCI4 are classified. The thermodynamics and kinetics of Ticl4 production by chlorination of TiO2 are discussed. Problems encountered in the chlorination and purification steps are outlined in detail. MOST of the current processes for the production of titanium metal require the use of TiC14 as a source of titanium values. This material can only be produced by a dry chlorination process, since it is immediately hydrolyzed in the presence of water. When pure, the tetrachloride is a colorless liquid boiling at 136°C. It fumes readily in moist air, reacting immediately with the moisture to form TiO, and HC1. History The tetrachloride was prepared as early as 1826 by DumasL who chlorinated a red hot mixture of carbon and TiO,. Since then, numerous other mixtures have been used including rutile, ilmenite, beneficiated ilmenites, titanium pigment, slags, and the various titanium metalloids such as TiN, TiCN, TiOC, and TiS2. S2Cl2, phosgene, and CC14 have been substituted for chlorine and CO has been used in place of carbon.

Jan 1, 1956

By C. H. Jr. Herty

FEW subjects have attracted the attention of metallurgists more than ,oxygen in steel. From the days of Mushet and Ledebur interest in this subject has been increasing, and as additional knowledge has become available, the problem has naturally grown more complex. Instead of using the simple term "oxygen" we now distinguish between iron oxide, silicates of various kinds, oxysulfides, oxygen as gas and oxygen in solid solution in steel. There are five general methods for determining oxides in steel: hydrogen reduction;, vacuum fusion; various wet-extraction methods, including electrolytic methods; methods depending on volatilization of the iron away from the oxides; and metallographic methods. For oxygen in solid steel each of these methods has both advantages and disadvantages. The hydrogen-reduction method is of no use on steels above about 0.20 per cent. carbon;1 furthermore, it gives only FeO and possibly some MnO. The vacuum-fusion method2 is expensive and gives total oxygen, with the exception of some A1203, and does not differentiate between the various oxides in which the oxygen exists. Most of the wet-extraction methods' give only the more insoluble oxides Si02 and A1203, though the iodine method gives MnO to an uncertain degree (information that may be more misleading then no information

Jan 1, 1930

By Andrew Balint, Peter Cammack

When coal is irradiated by the X-rays emitted from a plutonium 238 isotope, the radiation absorbed by elements of low atomic number (carbon and hydrogen) is lower than that absorbed by elements of high atomic number (silicon, aluminium, iron) which form the ash in coal. The differences are reproducible and readily measurable, and this paper describes how this technique is used to determine the ash content of coal and to optimize measurement accuracy. Uses of the output signal are given with an example of a simple control circuit, and the advantages of instantaneous ash measurement are highlighted in terms of operational convenience and profit.

Jan 1, 1977