Search Documents

By S. Sumski, M. B. Panish, R. T. Lynch

The liquidus isotherms in the gallium-rich corner of the Ga-Al-P phase diagram have been determined from 1000" to 1200°C and at I100°C the corresponding solidus isotherm was obtained. A simple thermody-namic treatment which permits calculation of the solidus and liquidus isotherms is discussed. A technique which was previously used for the growth of GaxAl1-xAs was used for the preparation of solution epitaxial layers of GaxAl1-xP and ALP. An approximate value of 2.49 i 0.05 ev for the band gap of Alp at 300°K was obtained and the ternary phase data were used to estimate a value of 36 kcal per mole for the heat of formation 0f Alp at that temperature. The Gap-A1P crystalline solid solution is one in which there exists the possibility of obtaining crystals with selected energy gaps, within the limits imposed by the energy gaps of Gap and Alp. Such crystals are of considerable interest because of their potential value for optoelectronic and other solid-state devices. Furthermore, it has been amply demonstrated for GaAs and GaP,'-7 that device, or bulk materials grown from gallium solution generally have more efficient radiative recombination than materials prepared in other ways. This presumably due to the lower gallium vacancy concentration in such material.= Small crystals of GaXAl1-xP and A1P have been grown from solution,8-10 and A1P has been grown from the vapor," but neither have previously been grown by liquid epitaxy. In this paper we present the ternary liquidus-solidus phase diagram of the Ga-A1-P system in the region of primary interest for solution epitaxy, and discuss the thermodynamic implications of that phase diagram with particular reference to the liquidus and solidus isotherms in the gallium-rich corner of the GaxAl1-xP primary phase field and to the A1-P system. Several measurements of the absorption edge of GaxAl1-xP crystals have been made and the width of the forbidden gap of A1P has been estimated from these measurements. EXPERIMENTAL The differential thermal analysis technique used to determine the liquidus isotherms and the optical measurements used in this work are similar to those described previously12 for the Ga-Al-As system, ex- thermocouples in the thermopile for added sensitivity. The materials used were semiconductor grade Ga, Gap, and Al+ The composition and temperature range at which DTA studies could be done was quite restricted. The upper temperature was limited by the chrome l-alumel thermopile to about 1200°C, and the highest aluminum concentration to about 5 at. pct by low sensitivity caused by the reduced solubility of Gap with increasing aluminum concentration in the liquid. DTA studies were not possible at 1000°C and below because of the low sensitivity caused by low solubility of Gap in the Ga-A1-P system. The cooling rate for these studies was about 1°C per min. No heating studies were done because of limited sensitivity. Supercooling probably does occur, but our experience with other 111-V systems indicates that it is no greater than about 10 to 15.c. Solid solubilities were determined by analyzing epitaxial layers of GaxAl1-xP grown from the liquid, with an electron beam microprobe. The layers were grown on Gap seeds by a tipping technique in which the layer is grown over a short-temperature range (20" to 50°C) on the seed from a solution of known composition. The tipping technique reported by Nelsson1 for GaAs could not be used, particularly for solutions containing appreciable amounts of aluminum, because of the formation of an A1203 scum on the liquid surface. A system was therefore designed, which would effectively remove the oxides mechanically, so that uniform wetting and crystal growth could occur. This tipping technique has already been described in detail." The best control over the composition of the re-grown layer was obtained when the tipping was done at a temperature which corresponded to the temperature of first formation of solid for the solution being used. Generally, therefore, a solution was prepared by adding the amounts of Ga, Gap, and A1 required to yield a solution which would be completely liquid above the tipping temperature with solid precipitating below that temperature. For most of the work reported here, the 1100°C isotherm of the ternary was used. It was generally necessary to heat the solution to 50" to l00. C above the tipping temperature to dissolve all of the Gap in a reasonable length of time. The epitaxially grown layers were used both for optical transmission measurements to aid in the estimation of the way in which the absorption edge changed with aluminum concentration, and for the electron beam microprobe analyses to provide data for the determination of the solid solubility isotherm. RESULTS AND DISCUSSION Liquidus Isotherms in the Ga-A1-P Ternary Phase Diagram: Thermodynamic properties of the system. The only thermal effect studied in this work was that

Jan 1, 1970

By F. H. Buttner, E. R. Funk, H. Udin

A. P. Greenough (University College, swansea, Great Britain)—I have recently made some experiments on the deformation of silver wire at high temperature in an atmosphere of oxygen-free nitrogen. The observa-tions which 1 made confirm the main conclusion of this paper, that the most satisfactory mechanism so far suggested to explain the deformation which takes place

Jan 1, 1953

By H. H. Reamer, B. H. Sage

The formation volume and the relative volume of the liquid Phase of mixtures of Condensate and gas from five different parts of a field in the Louisiana area have been established experimentally. These studies included gas-condensate ratios as high as 25.000 cu ft/bbl at pressures up to 5,000 psi. The gravities of the tank condensates were between 53.9° and 63.9° API. The compositions of the condensate and gas samples inves-ligated are presented in tabular form. The formation volume. the relative volume of the liquid phase. and the specific volume of the mixtures are available. A rough correlation of the formation volume as a function of pressure. temperature, and gas-condensate ratio has been presented. This correlation i-considered applicable only to the range of conditions covered in this investigation for systems of similar nature and com-position. INTRODUCTION Often a knowledge of the influence of temperature. Pres sure, and relative quantities of condensate and gas upon the volumetric behavior of fluid*. from a given field has been employed in estimating the Conditions existing in the reservoir. The early work of Beecher and Parkhurst' and the more rrcent Studies of the Dominguez' and San Joaqnin Valley Field;: are examples of experimental studies of this character. Correlation of the volumetric behavior of naturally occurring hydrocarbon mixtures has Proved To be feasible' . at low gas-conden-sate ratios-; for fluids*. from a single geographic area. Progres 5 is being made in the Prediction of the volumetric behavior of distillate systems at high gas-condensate ratios and pressure.. However. the estimation of the retrograde". ' dew-point pressure still remains uncertain and probably can best be established by experiment. For this reason it appears of interest to make available experimental information about the volumetric behavior of mixtures of condensate and gas from five different part.; of a single field. This material shows a rough similarity to data for mixtures of condensate and gas from San Joaqnin ' Valley Fields. In the present paper. 110 attempt has been made to coordinate the available information on tbe volumetric behavior of fluids from condensate fields. It appears hopeful that progress can be realized by the utilization of recently developed equa-tions of state.!' However. the primary problem in any such correlation is the proper identification of the components and constituents of naturally occuring systems. Additional experimental information may be required to permit the determination of the values of the constants of the equation of state for References given at end of paper. Manuscriptt received in the office of the Petroleum Branch June 11. 1951. *For present purposes low gas- condensate ratios will he considered as those below 3,000 cu ft/bbl, and the region of high gas-condensate ratio will be limited to compositions containing more than 5,000 cu ft of pas per bbl of condensate. Mixtures Containing between 3,000 and 5.000 CII ft OF gas per bbl will be considered of intermediate gas-condensate ratio.

Jan 1, 1952

By Campbell Hunter

PETROLEUM is found in almost every province in Persia. On the northern frontier, along the southern shore of the Caspian Sea, it is found near Anzelli and Shakhtesar and gas at Khoremabad. Oil is also found at Gumush Tepe, northwest of Astrabad, on the southeastern shore of the Caspian Sea. Further inland, to the south of Astrabad, oil is found at Schahkuh-i-balae, also on the margin of the Khorasan desert at Semnan, 115 mi. (35 m.) east of Teheran. Along the western frontier, from northwest to southeast, oil is encountered at Ouschachi, north of Lake Urumieh; in the province of Azerbaijan, at Zohab, Khanikin, and other places in the district of Kormanshah in the province, of Ardelan. Further south, in the province of Luristan, oil is found east of Mendeli and in the Pusht-i-kuh districts. Considerable quantities of oil are also obtained from Schuster, Maidan-i-Naphtun, Ram-Hormuz, Beheban, which are almost on a straight line, running northwest and southeast along the foothills of the Bakhtiari Mountains. At Ahwaz, in the province of Arabistan, oil has been found along another range of hills whose axis also lies in a northwest-southeast direction. In the Fars province, boring for oil has taken place at Daliki, and indications of oil are found at Kheri, Fasa, Darab, and other places. A gas show is also recorded at Kuhi-Sung-Atush in this province, 30 mi. (48 km.) east of Darab. In the south of Persia, oil is encountered on. Qishm Island, also at Ahmedi and other places north of Bunder Abbas. On the southeastern frontier, oil is found on the Sarhad range of hills. Thus, oil indications have been noted over a distance of approximately 1100 mi. along the western and 700 mi. along the northern frontiers of Persia.

Jan 2, 1920

By Charles Williams

BOYLE'S law states that the volume of a gas at B constant temperature varies inversely as its pressure, PV = C, or V = C/P Therefore, the volume of a gas at any pressure is to its corresponding pressure as the volume of the same gas at atmospheric pressure is to atmospheric pressure, V, = V° Also, P1 P0 the volume of the gas at any other pressure is to its corresponding pressure as the volume of the gas at atmospheric pressure is to atmospheric. pressure, V2/P1 V0/P0 V°P VA Solving for V1 and V2, V2 = and V2 =V0P2/P0

Jan 2, 1927

By S. D. Dahlgren

ORDERED G.P. zones having the cesium chloride structure were found to exist in the bcc iron-rich grains of an Fe-Au-Cu alloy that had been supersaturated with approximately equal atomic percentages of gold and copper, and aged at 400° and 350°C. Streaks and superlattice spots in electron diffraction patterns revealed the presence of the ordered zones in the aged material. The ordered Ll2 structure is commonly found for precipitates in fcc metals (e.g., Ni3A1 in nickelL7') but it is uncommon to find precipitates in bcc metals having the cesium chloride structure. The formation of the G.P. zones caused age hardening of the grains. Samples containing 3.8 at. pct each of gold and copper (with the remainder being iron) were annealed at 95@ or 1125°C in quartz capsules and were quenched by breaking the capsules under water. X-ray diffraction patterns revealed two solid solutions in the quenched samples. One solid solution was bcc and the other was fcc. The microstructure consisted of iron-rich grains of 0.3 mm diam surrounded by a yellow gold-copper-rich grain boundary network. The Au-Cu phase diagram %hows continuous solid solubility of gold and copper with ordered phases forming below 410°C. None of the ordered Au-Cu phases have the cesium chloride structure. Both Fe-Au and Fe-Cu phase diagrams3 show extended miscibility gaps and only terminal solid-solution phases. Consequently, it is reasonably certain the iron-rich grains consisted of an a-phase terminal solid solution, and the grain boundary network consisted of a gold-copper-rich terminal solid solution. Lattice parameters of the quenched solid solutions were consistent with the suggestion that the quenched phases were terminal solutions. The lattice parameter of the bcc phase (2.879A) obtained upon quenching from 950°C was higher than that (2.866A) for pure iron. The fcc phase in this sample had a lower lattice parameter than that for a 50 at. pct Au and 50 at. pci Cu solid solution, i.e., 3.866 compared to 3.877A. The lattice parameter for the 50 pct Au and 50 pct Cu solid solution was interpolated from data for Cu-Au solid solutions.4 More gold and copper were soluble in iron at 1125°C than at 950°C as indicated by a 0.012A increase in the bcc lattice parameter for a sample quenched from 1125°C. After the alloy had been quenched from 950° and 1125°C, the bcc lattice parameters were 2.879 and 2.891A1 respectively G.P. zones having the cesium chloride structure-which formed during low-temperature aging—were detected by electron diffraction and observed with electron transmission microscopy. In Fig. 1, the asymmetrical streaks parallel to ( 100) directions indicate that platelike G.P. zones had formed parallel to (100) planes of the matrix. The direction of streak asymmetry shows that the bcc unit cell of the G.P. zones was larger than the bcc cell of the matrix. The ordered cesium chloride structure is indicated by low-intensity superlattice spots at 010 positions which are nonallowed for bcc structures. The superlattice spots are streaked; therefore they are from the G.P. zones and are not caused by rel-rod effects of a thin matrix phase. The appearance and size of the zones observed in electron transmission microscopy and the appearance of the asymmetrical streaks in the electron diffraction patterns for the Fe-Au-Cu alloy were the same as those observed for a similarly treated Fe-Au alloy.' Ordered G.P. zones were detected also for an Fe-Au-Cu sample aged only at 400°C. The production of the ordered cesium chloride structure zones by low-temperature aging of super-

Jan 1, 1968

By H. R. Thresh, A. F. Crawley, D. W. G. White

The densities of liquid tin, lead, and Sn-Pb alloys have been measured over a range of temperature above the liquidus. In all cases, data can be adequately represented by an equation of the type p = a + bT. For pure tin, the values of a and b are, respectively, 7.139 and 7.125 x 10-4, and for pure lead, 11.060 and 12.220 x 10-4. At constant temperature, molar volumes in the Sn-Pb system vary linearly with composition. DURING the course of a long-term program at the Department of Energy, Mines and Resources, Ottawa, Canada, the densities of liquid tin, lead, and Pb-Sn alloys were studied. The work reported herein draws on two sets of results independently achieved by Thresh, on the one hand, and by Crawley and White, on the other. EXPERIMENT The method and apparatus were originated by Thresh and have been described in detail in Mines Branch reports.172 In operation, the 14 cu cm graphite pycnometer is put in the furnace as shown in Fig. 1 after a machined charge has been placed inside the pycnometer and the lid screwed down. The dimensions of the charge are such that, upon melting, a small excess of liquid metal is discharged through the capillary hole to displace the weighted float above. When the pycnometer has been equilibrated at the experimental temperature, the

Jan 1, 1969

The Library of the above-named Societies is open from 9 A. M. to 10 P. M. except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and publications of scientific and technical societies. Members of the Institute, with few exceptions are forced to spend a portion of their time in localities isolated from sources of information. To these the Library; through its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention: The Library is prepared, to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general Information on the geology and mineral resources of-all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape. HARRISON W. CRAVER, Director.

Jan 4, 1919

By R. G. Schaal

The Magma Mine at Superior, Arizona had an unimpressive beginning as a. worked out silver mine that was purchased in 1910 for $130,000 and then incorporated into the Magma Copper Company which has been continuously mining the deposit since 1915. Copper is the principal metal produced. However, zinc, gold, silver and iron have also contributed to the total metal product. Prior to 1973, the production rate of 1500 tons per day was maintained by hoisting 4 and 5 ton pay-loads at speeds up to 1100 FPM through four small hoisting shafts. The hoists used included 8' and 7' diameter double drum, double clutched doc. and a.c. motor driven geared units built as early as 1917. One old timer that did yoeman's service for many years was an 8' Bollen Pulley with a.c. geared drive that utilized an endless rope system with mechanical grip and release mechanism built into the pulley's throat. Primary power for all of these old production hoists was 25 Hertz. Exploration that was completed in 1967 developed a reserve of 10 Million tons of 5 per cent copper which was sufficient to justify new capital expenditures for enlargement of productive facilities to 3300 tons per day. To reach the new reserves a 22' I.D. concrete lined vertical shaft was sunk to an initial depth of 48431. A 12 ½ diameter adit was bored from the mill side of the mountain to intercept the shaft at a point about 1100' below the collar. This 9200' long adit provides the right-of-way for the mine to mill railway and egress for heavy supplies from rail head as well as a conduit for potable water, electric power, compressed air and mine drainage. Mine operating levels begin 3582' below collar and thereafter have been cut at 100' vertical intervals. Skip loading stations have been installed 4282' and 46821 below collar with an in-shaft skip dump station located 800' below collar. This provides for 4500 tons of storage above the mine to mill train loading station located 1100' below collar. Ore and waste are moved horizontally from stope chutes and drift headings by rail haulage to transfer raises which channel all material to the two mentioned skip loading stations. The 22' diameter shaft crossection is arranged with the two skip compartments on the south side separated from the manway and utility compartments by the cage compartment. The cage counterweight operates in a portion of the southwest quadrant of the shaft. The hoisting plant consists of two conventional Nordberg double drum, single clutch, geared, d.c. motor driven units that are identical except for the drives and automatic controls. The drums are 15' diameter x 105" face with LeBus grooving for 2-1/8" diameter wire rope wound in three layers. Mechanical design emp1o::ed is the same as has been used for the past twenty- five years. One drum is attached to the main shaft by 2 large bolted integral shaft flenge. The loose drum is engaged by a 4-arm positive tooth clutch meshing with radially cut teeth of the clutch ring which is bolted to the drum. The drums are one-piece steel plate weldments having a finished weight of 60 tons each and are mounted upon a 36" diameter shaft that also weighs 60 tons. With the addition of brake rings, clutch, bull gear and rope, the total dead weight adds up to nearly 250 tons that is supported by just three double row spherical roller pillow block bearings. There is no bearing between the drums. All pinion shafts as veil as all head sheave journals are supported in the same type of antifriction bearings.

Jan 1, 1975

By B. M. Larsen, K. Heindlhofer

Jan 1, 1945

By W. L. Chen

The Batac jig was first introduced in the US for fine coal cleaning in 1973 (Tackett, 1977; Hake, 1976). Since then, a total of six such jigs of various sizes have been installed in five US plants for a total capacity of 2346 t/h. The raw coal size ranges from 19 mm x 0 to 9.5 mm x 0-fraction sizes previously fed to heavy medium cyclones, Deister tables, or water only cyclones. Growing interest in the Batac jig as a replacement for the above equipment is due to the following reasons: • Unlike heavy medium cyclones, no magnetite is required. As a result, the operating cost of the plant is reduced. • The compactness of equipment is unique on a unit ton per hour basis as compared to other equipment. • Solid state electronic control of jig stroke length, frequency, and jig bed depth makes the equipment highly efficient. Installations of Batac jigs in the US as of June 1980 are shown in [Table 1]. Use of the Batac jig is even greater outside the US (Anonymous, 1980; Chen, 1980). Its use is not limited to fine coal but is applied to coarse coal as well, with 102 mm size in the feed (Zimmerman, 1975). In countries where consumption of magnetite associated with the heavy medium system of coal cleaning is considered a waste of iron ore resource, the Batac jig is regarded as the primary choice in the selection of cleaning equipment (Chen, 1980).

Jan 1, 1981

By James Lorimer

THE topography at the Stan Trg mine facilitated early exploration by adits; in consequence adit levels were developed at horizons 865, 795, and 760 meters above sea level, and the levels in the mine 'are named according to their elevation. Exploitation started from the 760-m. level . upwards while simultaneously first steps were taken with regard to mining in depth. A deep dewatering adit 2.5 km. long now gives access to the deposit at the 610-m. horizon which also is connected with the 760-m. adit level by a three-compartment main hoisting shaft. Main levels have been developed internally from

Jan 1, 1936

By W. M. Small

Austria.—Austria produced some 430 cisterns of 10,000 kg. each of crude oil of a 0.9428 sp. gr. during 1934. Gosting II well near Zis-tersdorf was placed on the pump in August and at the end of the year was still producing about three cisterns daily. This well is owned by the Erdöl-Produktionsgesellschaft while Gösting I is owned by Raky-Danubia. Only five wells were completed in the republic during the year. These accounted for 1783.5 meters of the 2225 meters drilled. The only producer completed was Gosting 11. At the close of the year, four rigs were in operation and one rigging up. At least 8 or 10 new wells are planned in Lower Austria for 1935. The European Gas & Electric Co. put its 6-km. gas line into operation in May and has sold 12,301,550 cu. m. of gas to the Vienna City Electric Works. A 2-km. pipe line was built from Gösting II to the railway loading rack near Zistersdorf. Hungary.—No oil or gas was produced except a small amount of gas trapped from flowing artesian wells. The Government completed and abandoned a 1500-m. hole at Tisztaberek in northeastern Hungary and is drilling at 967 m. near Bogáes, 120 km. northeast of Budapest. It is unofficially reported it plans to drill two new wells in 1935. The European Gas & Electric Co. has a rig up for a test at Mihalyi in Transdanubia. Czechoslovakia.—In Gbely (Egbell) there were produced 1283 cisterns of 10,000 kg. of 0.935 sp. gr. oil and a small amount of gas used for fuel. This field is operated by the Government; 17 shallow producing wells and three dry holes were drilled, with a total of 3351 m. of hole completed. In Hodonin (Goding) there were produced approximately 1300 cisterns of 10,000 kg. each of 0.91 sp. gr. oil and a small amount of gas used for fuel. The field is operated by the Apollo, which drilled four producing wells averaging 460 m. in depth, one small gas well of 550 m., one small gas well 260, and one dry hole 230 m. Two wells were deepened a total of 80 meters. The Government is drilling below 800 m. in a wildcat test in eastern Czechoslovakia near the Rumanian frontier.

Jan 1, 1935

By Alfonso W. Ovalle

INTRODUCTION The block-caving mining method is one of the most economical ways existing today to extract ore from nature. It is undoubtedly the least costly of the underground systems and moreover it compares favorably to open-pit mining. In addition to its low cost characteristic, the block-caving mining method permits a great extraction volume as can be exemplified by El Teniente's output capacity of over 22 million tons of ore per year. These characteristics of block-caving give assurance that, even though it is a very old mining system, it will be a good answer to the many future large massive low ore grade deposits to come and a1 so to rep1 ace open-pi t mining as such operations get deeper with higher stripping ratios. These are the reasons that induce further study of block-caving. In this paper block-caving at El Teniente is analyzed with due consideration to the major problems that this mine will encounter. Emphasis is given to the factors influencing the mining of soft ore which accounts for most of the ore to be extracted in the next ten years. A separate paper is devoted to a major modification introduced to block-caving hard primary ore at El Teniente by means of LHD equipment extraction. DESCRIPTION OF THE PRESENT MINING Ore Production and Flow Over 62.000 tons per day of ore are extracted 359 days per year at the El Teniente Mine. The Teniente 8 train haulage level at 1.983 m takes 29.000 tons daily to the Col6n Concentrator. Two trains make the 8 km haul with 16 cars per train. Car capacity is 90 tons. The Teniente 5 train haulage level 298 m above takes 33.000 t per day to the old Sewell Concentrator. Ore is produced from three production areas in two different levels. The so called North Mine produces 42.000 tons daily from the Teniente 4 level 65 m above the Teniente 5 haulage level. The Central Mine produces 1.000 tons from the first hard rock block caved at the Te- niente 4 level. The combined 43.000 tons per day production is sent through inclined 2 m dia- meter raises to the Teniente 5 haul age level , where 33.000 tons are taken 2.5 km to the Sewell Concentrator and 9.000 tons are hauled 0.5 km to a 5 m diameter vertical ore pass which sends ore to Teniente 8. The haulage is by 7 trains, 15 gabble-bottom cars per train. Car capacity is 20 tons. The so called South Mine produces 19.000 tons per day from the Teniente 1 level 645 m above the Teniente 8 haulage level. Ore is transferred by 2 m diameter inclined raises to the Ten 1 Retram level 22 m below, where 5 trains with 20 Sandfor Day cars per train, 8 tons capacity per car, haul the ore 1.5 km to two vertical 5 m diameter ore passes which connect to Ten 8. Starting in 1982 the Central Mine will in- crease production to 6.000 tons per day. An in- dependent loop haulage system will start operat- ing at the Teniente 5 level to feed a new under- ground 1.372 mm (54 in.) gyratory crusher which will send minus 152 mm ore (9 in.) to Teniente 8. In two or three years time the North Mine will only feed the 33.000 tons to the Sewel 1 Concentrator with its old Teniente 5 haulage system. The Col6n Concentrator will be fed from the Central and South Mines. Figure 1 shows the transfer systems and ore flows. The Ore Body In plan view at the Teniente 4 level the ore body has a kidney shape 1.800 m long and between 400 to 700 m wide. The north-eastern section of the ore body was washed away by the Teniente River. At the Sub 5 Level, 125 m below Teniente 4, the mineralization completely surrounds the circular 1.000 m diameter steep-sided barren breccia pipe (Braden pipe) . The ore body rock is 73% andesite, 14% diori te, 13% dacite and 6% mineralized breccia. Most of this ore is secondary enrichment sulfides which apart from the dacite is strongly fractured being chal cocite, cove1ine , bornite and

Jan 1, 1981

One of the best known of the early mining districts of Nevada was that at Eureka, where gold was first produced in 1864. While the most productive period for the district was during the early 1900s, production was maintained until World War II. During this time it is said that the Eureka district produced as much as $200 million from over 3,200 km (2,000 miles) of tunnels and workings. The Windfall Mine was discovered in 1902; and a 100 ton cyanide plant was operated there during the periods 1907 to 1912 and 1932 to 1940. Since 1974, however, Windfall Venture has been operating a unique heap leaching facility on the site of the old Windfall Mine. Gold at the Windfall occurs primarily in the Cambrian Hamburg dolomite which has been "sanded" and in which the original cementing material has been destroyed. The gold is micron sized and is accompanied by anomalous amounts of arsenic and mercury; however, the ore is low in base metals which distinguishes it from the typical Eureka district ores. Mining the ore causes it to break down into very fine sizes, approximately 50% minus 150 microns (100 mesh). Conventional heap leaching by spraying proved to be impossible; and extensive test work on alternate methods, aided by the United States Bureau of Mines, was conducted using 9 m (30 ft) high columns and then large tonnage heaps. The leaching procedure adopted was to build 10.6 m (35 ft) high heaps on a 50 mm (2 in.) asphalt pad covered with a layer of gravel for drainage assisted by perforated pipe drains and gravel-packed sumps. A berm is constructed around the top of each pad and cyanide solution is allowed to “pond” on top of the heap. The resulting percolation is at the rate of 24 liters per sq m per hr (0.6 gal per sq ft per hr), a figure about 2.4 times the average used in other heap leaching operations. The dolomite furnishes its own protective alkalinity and no lime or caustic is used in the solution which contains 0.4 kg per mt (0.8 lb per st) of NaCN. Pregnant solution from the heaps averages about 0.7 g Au per mt (0.02 oz per st) with a cyanide content of about 0. 2 kg per mt (0.4 lb per st) and a pH of plus 9. Addition of NaCN brings the pH of the leach solution up to 11 to 12. Carbon adsorption of the gold was originally done in six enclosed columns mounted in a trailer but five conventional columns have been substituted as the size of the operations has increased. Carbon stripping is with hot caustic, cyanide and 10% ethanol solution. The

Jan 1, 1981

Connecticut Geological and Natural History Survey, P O Box 1106, New Haven, Conn W. E Britton, Superintendent. A complete list of Bulletins available will be sent upon request. Address all inquiries for publications to: George S Godard, State Librarian, Hartford, Conn Fifty-one Bulletins have been issued, 15 of which are of particular interest, dealing with the geology of the state, and are available as follows; 4, The clays and clay industries of Connecticut, by G. F Loughlin (1905), 35 cents; 8, Bibliography of Connecticut geology, by H E Gregory (1907), 20 cents, 13, The lithology of Connecticut, by J Barrell and G. F Loughlin (1910), 45 cents, 18, Triassic fishes of Connecticut, by C. R Eastman (1911), 30 cents, 23, Central Connecticut in the geologic past, by J. Barrell (1915), 20 cents, 24, Triassic life of the Connecticut Valley, by R Lull (1915), 70 cents, 29, The Quaternary geology of the New Haven region, Connecticut, by F. Ward (1920), 60 cents, 30, Drainage modifications, and glaciation in the Danbury region, Connecticut, by Ruth S. Harvey (1920), 55 cents, 33, Geology of the Stonington region, Connecticut, by L H. Martin (1925), 60 cents, 40, The geology of the Shepaug Aqueduct Tunnel, Litchfield County, Connecticut, by W M. Agar (1927), 50 cents; 41, Guide to the geology of Middletown, Connecticut, and Vicinity, by W. N Rice and W. G Foye (1927), $1, 44, Report on the water resources of Connecticut, by R. H Suttee (1928), $1, 46, The physical history of the Connecticut shoreline, by H S Sharp (1929), 75 cents; 47, The glacial geology of Connecticut, by R F. Flint (1929), $2, 51, Minerals of Connecticut, by J F Schairer (1932), 75 cents Bulletin 51 explains the physical and chemical properties of minerals, their classification, and describes more than 100 common minerals found in Connecticut. A bibliography is included The Survey gratuitously distributes all its Bulletins to state residents, scientific institutions, etc. Prices quoted are to private citizens of other states

Jan 1, 1933

By H. W. Morse

THE CHAIRMAN (H. W. MORSE).-Gentlemen, for the first time in the history of the American Institute of Mining Engineers, we have a full session on the subject of leaching-especially on the leaching of copper ores.. This branch of metallurgy is rather in its infancy. We have had one big plant running for a year or more, and pretty successfully; and another one which will be started in February or March, the New Cornelia. We have another one at Garfield for the Utah company, which is just designed and construction begun; and from several other points come reports of interesting test work. The first paper on the program this evening is one of some of the test work on the New Cornelia ore by myself and Mr. H. A. Tobelmann. LAWRENCE ADDICKS, New York, N. Y. (written discussion).-The Ajo proposition has had, as I understand it, two great advantages: it has not been obliged to measure leaching against flotation or some other metallurgical process, and it deals with a copper content high enough

Jan 12, 1916

By C. L. HUSTON

MY ANCESTRAL connection with the manufacture of boiler plate runs back through four generations, and my personal acquaintance with the practice reaches back to the time, in my ,boy- .hood days, when iron plates' were made in a mill operated entirely by water power. -The mill originally was driven by an old-fashioned "'breast" water wheel 20 ft. in diameter and with a20-ft. face, geared direct to the roll train. When the mill slowed up and there was danger of its stalling, the men would jump upon the rim and help the wheel around with their weight, to prevent a "sticker." Later, as large plates were called for, a flywheel was set out of line so that it could' be speeded up by gears from the water wheel and connected back again,. by reducing- gears, to the roll train. The flywheel, with its cast-iron rim and wooden spokes, made 90 r.p.m. and the roll train 45 r.p.m. In 1870, our company installed our first steam-driven plate mill two-high rolls, 84 in. long. In these early mills the hot metal was manipulated by hand.

Jan 1, 1920

By O. W. Shimer, D. C. Helms, C. E. Brown

The early history and progress of anthracite stripping, from the first known operation at Summit Hill in 1821 through 1917, was covered in 1917 in a paper by J. B. Warriner,1 then chief engineer, now president of the Lehigh Navigation Coal Co., and stripping methods between 1917 and 1931 were the subject of a paper in 1931 by H. H. Otto,2 of the Hudson Coal Company. The present paper is confined to methods used today on pitching beds in the western middle and southern anthracite fields. The anthracite industry, not unlike other large industries, had been affected for more than a decade by the adverse economic conditions of the country. High development and operating costs and the competition of other fuels caused some collieries to be closed temporarily, while others were permanently abandoned. In order to obtain a larger tonnage at a lower development cost, a larger stripping program was put into effect by many companies. In 1932, stripping operations accounted for 3½ million tons, or 7 per cent of the total anthracite production of the year, and in the next 10 years this increased until more than double that amount, or over 14 per cent of the total production, was from stripping operations. These figures represent the total production of the entire anthracite region; unfortunately, the figures have not been separated from the different fields. There are some operations in the southern and middle western fields where the tonnage obtained from stripping amounts to more than 30 per cent of the total colliery production. Stripping operations on pitching beds present difficult problems. Owing to the various geological formations, a different situation is encountered in nearly every stripping pit; and because of the proximity of an overlying bed, it is very often necessary to load the entire overburden into trucks and haul it out of the pit to the dump area, although back filling and casting is done whenever possible. Beds in the areas described in this paper pitch from 20" to 90° and some are on the invert in many sharp folds and faults. Planning The more successful strippings have had adequate engineering analysis. Some work is being done without much preliminary planning, but many strippings would have failed completely if close supervision by the engineering department had not been maintained. Locations of stripping areas are determined as follows: I. By constructing cross sections over the areas and drilling sufficient diamond-drill or well drill holes to study the strata and to determine the location, thickness and pitch of the beds.

Jan 1, 1946

By Samuel S. Arentz, Dorsey A. Lyon

Introduction % •................. 789 The Present Sources of Zinc ..:.......... 791 Zinc Ores.................. 791 Lead-Zinc Ores................. 793 Loss oF Zinc at the Mine.............. 793 Present Method oF Extracting Zinc From Ores....... 795 Class oF Ores Suited to Zinc Retort Smelting....... 795 Concentration Processes Used for Treating Zinc Ores .... 795 Hydro-Mechanical Processes............. 795 Electro-Mechanical Processes............. 796 Flotation Processes............... 797 Losses of Zinc in Lead and Copper Blast-Furnace Smelting .. 798 Possible Future Sources oF Zinc Supply.......... 800 The Problem oF the Metallurgist and the Present Status of New Processes................. 801 Introduction A great deal of attention has recently been given to the metallurgy of zinc, and much of that which has been said and written on this subject has been in the nature of a criticism. For instance, we are quite accustomed to hearing it said that the metallurgy of zinc has stood still, that it is antiquahed, out of date, etc. We are, however, inclined to agree with George C. Stone1 when he says that, although there have been no such spectacular and radical changes as were worked in the metallurgy of copper and iron by the introduction of converters, there has nevertheless been a decided and marked progress in the metallurgy of zinc, and especially during recent years. However, it must be admitted that, due to the fact that the chemistry of zinc is so different from that of the other metals, the retort process is the only process by which zinc is produced commercially; and, moreover, that losses which occur in the zinc industry— that is, in the mining, milling, and smelting of zinc ore—are very great, for it is stated2 that probably less than 50 per cent. of the zinc mined, even

Jan 1, 1915