Search Documents

By R. W. Gurry

In the course of a series of measurements of the rate of diffusion of carbon in austenite at about 960°C. (1760°F.) and III0°C. (2030°F.), it became necessary to determine carbon concentration when austenite is saturated with graphite, because of indications that the hitherto accepted value of the solubility of graphite in this temperature range is too low. Specimens of carbonyl iron were saturated at temperature in a hydrogen-toluene atmosphere which was in equilibrium with graphite. The carbon conteDt of the steel was measured either by combustion or by the loss of weight after substantially complete decarburization in an atmosphere of hydrogen saturated at room temperature with water vapor. The absence of carbide or graphite as a phase at temperature was demonstrated by microscopic examination of saturated specimens that had been drastically quenched, The mean result of concordant ments-—taeats-is-^that gamma iron saturated with respect to graphite contains 1.39 per cent carbon at 957°C .(i755°F.) and 1.89 per cent at III0°C. (2030°F.). These two values, plotted along with what appears from the literature to be the best value (0.69 per cent) at the iron-graphite eutec-toid temperature (738°C. or I360°F.), yield a curve that is almost linear, and which, continued upward through a short interval, leads to a limiting solubility of 1.98 per cent at the iron-graphite eutectic temperature II35°C. (2075°F.) instead of the commonly accepted value of about 1.7 per cent. Experimental Procedure The samples of carbonyl iron, with the exception of those for microscopic examination, were cylinders 3.8 cm. long, 0.475 cm. in diameter. They were placed in a graphite holder and suspended in a vertical furnace, the temperature of which was controlled precisely by means of the resistance of the platinum winding.' In the empty furnace the range of temperature over a distance of 4 cm. at the heat center was 9°C. (I6°F.) but at a given location the temperature remained within +o.5°C. (o.9°F.); it was measured by inserting a platinum-rhodium couple calibrated at the melting point of palladium, 1555°C. Since the presence of the sample probably improved the uniformity of temperature, it was decided to consider the average temperature of the sample to be 3°C. lower than the maximum measured in the empty furnace with the same setting of the controller. Data were obtained in the vicinity of two temperatures, 960°C. (I760°F.) and III0°C. (2030°F.). The samples for microscopic examination, 2.2 cm. long, 0.475 cm. in diameter, were suspended individually on pure iron wire; for these no temperature correction was applied. The carburizing gas passed into the furnace was dry, oxygen-free hydrogen saturated at room temperature with toluene; this quickly produced on the

Jan 1, 1942

By R. W. Gurry

In the course of a series of measurements of the rate of diffusion of carbon in austenite at about 960°C. (1760°F.) and III0°C. (2030°F.), it became necessary to determine carbon concentration when austenite is saturated with graphite, because of indications that the hitherto accepted value of the solubility of graphite in this temperature range is too low. Specimens of carbonyl iron were saturated at temperature in a hydrogen-toluene atmosphere which was in equilibrium with graphite. The carbon conteDt of the steel was measured either by combustion or by the loss of weight after substantially complete decarburization in an atmosphere of hydrogen saturated at room temperature with water vapor. The absence of carbide or graphite as a phase at temperature was demonstrated by microscopic examination of saturated specimens that had been drastically quenched, The mean result of concordant ments-—taeats-is-^that gamma iron saturated with respect to graphite contains 1.39 per cent carbon at 957°C .(i755°F.) and 1.89 per cent at III0°C. (2030°F.). These two values, plotted along with what appears from the literature to be the best value (0.69 per cent) at the iron-graphite eutec-toid temperature (738°C. or I360°F.), yield a curve that is almost linear, and which, continued upward through a short interval, leads to a limiting solubility of 1.98 per cent at the iron-graphite eutectic temperature II35°C. (2075°F.) instead of the commonly accepted value of about 1.7 per cent. Experimental Procedure The samples of carbonyl iron, with the exception of those for microscopic examination, were cylinders 3.8 cm. long, 0.475 cm. in diameter. They were placed in a graphite holder and suspended in a vertical furnace, the temperature of which was controlled precisely by means of the resistance of the platinum winding.' In the empty furnace the range of temperature over a distance of 4 cm. at the heat center was 9°C. (I6°F.) but at a given location the temperature remained within +o.5°C. (o.9°F.); it was measured by inserting a platinum-rhodium couple calibrated at the melting point of palladium, 1555°C. Since the presence of the sample probably improved the uniformity of temperature, it was decided to consider the average temperature of the sample to be 3°C. lower than the maximum measured in the empty furnace with the same setting of the controller. Data were obtained in the vicinity of two temperatures, 960°C. (I760°F.) and III0°C. (2030°F.). The samples for microscopic examination, 2.2 cm. long, 0.475 cm. in diameter, were suspended individually on pure iron wire; for these no temperature correction was applied. The carburizing gas passed into the furnace was dry, oxygen-free hydrogen saturated at room temperature with toluene; this quickly produced on the

Jan 1, 1942

By J. D. Edwards

When Charles Martin Hall invented the electrolytic process for the production of aluminum, one basic requirement was a supply of pure alumina. Now, more than 50 years later, the same requirement still holds, and there are no technical straws in the wind to indicate that this situation is likely to change. Long ago, Aluminum Company of America took a number of steps to see that this country should not face shortages of alumina and aluminum in time of emergency. As one step to this end, the Company developed and used a supply of bauxite in South America in order to conserve dwindling Arkansas reserves. Another, and more a program than a step, was to investigate every type of process that might bear the possibility of utilizing the low-grade ores of aluminum that are more plentiful than bauxite. It is a long story, but the investigation included electric-furnace processes, acid extraction processes and alkaline extraction processes, with or without preliminary furnace and sinter treatments. Some of the processes developed were operated in commercial production. This work has been continuous since the first World War. The turn of the wheel came sooner than was expected when, in 1942, bauxite shipmerits through the caribbean became uncertain and hazardous through the operation of submarines. The tremendous requirements of aluminum for the war effort were consuming high-grade bauxite at an alarming rate and a national search for substitutes began. High-grade bauxites, for technical and economic reasons, have been defined as those containing about 7 per cent or less of silica. While bauxite of this grade was limited in amount in the United States, there was in sight a substantially greater volume of low-grade, high-silica bauxite not amenable to economic treatment by the Bayer process, but richer in alumina than the clays or other available low-grade ores. It was at this point, and after several years of intensive research on this particular phase of the problem, that Aluminum Research Laboratories brought to completion the invention of one of its research staff, which made practical the utilization of large reserves of low-grade bauxite in America. Bayer Process The Bayer process has been almost universally used for the production of alumina from bauxite. This process, in outline, comprises the digestion of hely ground bauxite in a solution of caustic soda (NaOH) under pressure and at an elevated temperature. Alumina in the bauxite goes into solution as sodium alumi-"ate and the impurities—oxides of iron, titanium and silicon—remain undissolved. The undissolved residue, known as "red mud,'' from its color, is separated and run to waste. AluKlinum hydrate (A12O3.3H2O) is precipitated from the solution of sodium aluminate, and the liquor containing the caustic soda and some alumina is returned to the Process for digesting more bauxite. The aluminum hydrate, after washing, is calcined at a high temperature to produce

Jan 1, 1949

By T. N. McVay, E. E. Creitz

INTRODUCTION Object RATHER large amounts of titanium minerals and some zircon and monazite are being recovered from dune sands about 10 miles west of Jacksonville Beach, Fla. The Mining Branch of the Bureau of Mines, Southern Experiment Station, has been interested in developing additional large deposits of similar sands in other areas of Florida. The results of a field study have been published1 concerning the sands occurring on Trail Ridge which runs north and south about 30 miles southwest of Jacksonville. This investigation was undertaken in order to identify the opaque titanium minerals occurring in Trail Ridge and because of the economic importance of Florida titanium minerals. Nature of the Problem The minerals present in the heavy fractions (sp gr > 2.94) of the sands are principally opaque minerals; staurolite, zircon, sillimanite, tourmaline, kyanite, rutile, a small amount of corundum, traces of the zinc spinel gahnite and garnet. Epidote, monazite, hornblende and titanite are present in other dune sands but these minerals were not noted in the samples collected on Trail Ridge. All of the minerals except those which are opaque can be readily identified by the usual petrographic methods. However, opaque minerals cannot be examined satisfactorily by transmitted light. Polished sections of the opaque-mineral grains were examined but these sections did not furnish useful information. Consequently, it was necessary to use means other than the usual petrographic methods to identify them. Previous Investigations of Heavy Minerals in Florida Sands Martens2 has described the heavy minerals in the Florida beach sands and has classified the opaque minerals as ilmenite with minor amounts of leucoxene. Miller3 studied a number of sands collected by Ross and Mertie in Florida. He states that the material from the Florida beach and dune sands that commonly has been called ilmenite has essentially the chemical composition of the material that has been called arizonite.4 The X ray diffraction patterns of several samples indicated that the supposed ilmenite is essentially amorphous, with only weak lines corresponding to ilmenite, and hence the material is unlike the type of arizonite from Arizona. Opaque Titanium Minerals Rutile is essentially titanium dioxide. However, as pointed out by Dana,5 important amounts of Fee and Fe3 as well as Cb and Ta are reported in some analyses.

Jan 1, 1947

By Leslie Burris, J. C. Hesson

The diffusivity of uranium in liquid cadmium has been measured as a function of temperature by the capillary -bath technique. The diffusivity measurements were made at 4509 500°, 575º, and 650°C, over which temperature range the diffusivity of uranium varied from 1.3 to 2.3 x 10-5 sq cm per sec. The diffusivity of uranium in cadmium was less than that predicted by the Einstein-Stokes equation. VERY little information is available on the diffusivity of uranium in liquid metals. Bonillal has reported a single measurement of the diffusivity of uranium in bismuth. Measurement of the diffusivity of uranium in cadmium was undertaken, not only to supply data in an area in which a dearth of information exists, but also because of a need for this physical property measurement in connection with mass transfer studies now underway in the U-Cd system at Argonne National Laboratory. The capillary-bath method used in this work has been successfully used by other workers2"4 to obtain diffusivities in liquid metal systems. Although considerable experimental technique is required to obtain reliable diffusivity measurements, the basic information required is only that of temperature, capillary tube length, the initial and final compositions of the alloy in the capillary tube, and the composition of the bath into which the solute element is diffusing. From these measurements, diffusivities may be calculated using Fick's law. The diffusivity equations are presented in the Appendix. Equations which are often used to predict diffusivities in dilute solutions5 are the Einstein-Stokes equation: D= (kT)/(6pµr) and the Eyring equation: D = (?,kT/?y?zp), where D= diffusivity (sq cm per sec), k = Boltzman's constant, T= temperature ("K), p = viscosity (poises), r = radius of diffusing molecule or species (cm), and A,, Ay, and A, are the diameters of the diffusing molecule in the three axial directions. For round molecules, the Eyring equation gives values which are 37r times larger than the Einstein-Stokes equation. In this work, the experimental values were compared to the Einstein-Stokes equation. Experimental values of diffusivities in liquid metal systems usually lie between those predicted by the Einstein-Stokes and Eyring equations. The viscosity values for cadmium were obtained from the Liquid Metals Handbook.6 EXPERIMENTAL APPARATUS AND PROCEDURE The general procedure employed consisted of rapidly immersing in a molten cadmium bath containing a negligible amount of uranium a capillary

Jan 1, 1963

By R. D. Carnahan, J. E. White

ThE use of strain gages in the measurement of microplastic behavior of materials is well-known.'-3 Recently it has been suggested that similar techniques might be useful for determining stress relaation. It is the purpose of this report to comment on the use of strain gages in the measurement of strains in the vicinity of 10"6. We will also discuss observations of an anomalous anelastic behavior apparently associated with small temperature changes, which accompanies the unload portion of a load-unload microstrain test. The key to successful strain determinations at levels below 1 pin. per in. is a good gage-mounting technique and either precise ambient temperature control or a set of matched temperature-compensated gages. The importance of good mounting cannot be overemphasized, for example, as in the use of Eastman 910 contact cement. If the cement layer is not sufficiently thin and properly hardened, it is possible to observe anomalous negative stresses when small loads are removed, which relax back to zero in an orderly way with time. Such anomalous behavior, thought to be due to gage bonding, has been reported in microstrain experiments by Thomas and verbach' who observed a negative strain of -3 X lo-' upon unloading. This kind of behavior severely limits the over-all strain sensitivity which can be achieved in such tests. The relaxation of a small positive strain subsequent to unloading in a load-unload experiment is quite normal, however, and is to be expected. The occurrence of an apparent negative strain is also encountered in those instances where the elasticity of the bonding cement is exceeded—for example 0.5 pct or 5000 pin. for cured Eastman 910. An elastic strain of this magnitude can be encountered during load-unload type testing particularly in higher-strength materials (-150,000 yield strength). During the course of microplasticity studies on pure nickel and nickel alloys,' the authors have made the following observation. In a four-point bending test, two active gages are mounted one on each side of the beam as arms R1 and R z of a conventional strain-gage bridge circuit shown in Fig. l(a). This technique provides two advantages: the sensitivity is doubled because R1 and Rz experience opposite strains and temperature compensation is provided automatically because any ambient temperature change would cause both gages to see a strain of like sign whose signals would cancel in the circuit.

Jan 1, 1964

By J. Gurland

THE microstructure of sintered carbides consists of particles of metal carbides, such as WC and TiC, embedded in a metallic binder which is usually a cobalt—or nickel-rich solid solution. One of the important factors influencing the strength of the alloys is the degree of dispersion of the carbide particles in the binder matrix. While it is generally accepted

Jan 1, 1960

Committee on Reduction and Refining of Copper............ 3 A.I.M.E. Officers and Directors.................... 4 Preface. By C. R. Kuzell....................... 7 Career and Achievements of James Douglas. By Arthur L. Walker. . 9 PAPERS Smelting 1. Reverberatory Smelting Practice History of Reverberatory Smelting in Montana, 1879-1933. By Frederick Laist..............................23 Reverberatory Smelting of Raw Concentrates at the International Smelter, Miami, Arizona. By P. D. I. Honeyman (With Discussion)...... 88 Development of Gun-feed Reverberatory Furnaces at Garfield Plant of American Smelting and Refining Company. By R. A. Wagstaff (With Discussion)........................99 An Experimental Combination of Shaft Roasting and Reverberatory Smelting. By Frederick Laist and J. P. Cooper (With Discussion).... 104 Forms of Copper Found in Reverberatory Slags. By Royal B. Jackman and Carle R. Hayward (With Discussion).............111 2. Converting Practice Development of Copper Converting at Butte and Anaconda. By William Kelly and Frederick Laist...................122 Developments in Converting Lead and Copper Matte at Tooele. By B. L. Sackett.............................132 Messina Stationary Basic Copper Converter. By R. G. Knickerbocker (With Discussion)........................140 Smelting Copper Concentrates in a Converter. By George E. Beavers. 149 Sulfuric Acid from Converter Gases. By George E. Beavers......151 Development of Monolithic Tamped Periclase Converter Linings at United Verde Copper Company Smelter. By F. H. Parsons (With Discussion) . 153 3. Descriptions of Plants The Noranda Smelter. By W. B. Boggs and J. N. Anderson......165 Smelting Operations at Roan Antelope Copper Mines, Limited. By Charles R. Wraith.......................202 4. Waste-heat Boiler Practice Copper-refinery Waste-heat Boilers at Great Falls Reduction Department, Anaconda Copper Mining Company. By E. S. Bardwell......225

Jan 1, 1934

By Alden B. Greninger, Alexander R. Troiano

THE crystallographic mechanism for the austenite-to-martensite transformation has been deduced from the results of the following new experimental determinations: (I) the accurate evaluation of the lattice relationship between austenite and individual crystals of martensite-and thus the relationship between the martensite lattice and the martensite plate, and (2) the measurement and analysis of the change in positions that a volume of austenite undergoes when it transforms into a crystal of martensite. For the latter study, a new tool was developed, the stereographic analysis of shear. Lattice relationship.-Thirty-five separate 50-gram melts of an alloy containing about 22 per cent nickel and 0.8 per cent carbon were prepared in a high-vacuum furnace. This alloy is all-austenite at room temperature; grain size was about I cm. Specimens of the alloy were cooled to about -70°C. to form a few martensite crystals, and suitable specimens were ground and polished on a surface parallel to a single martensite plate, exposing the martensite crystal for an area of I mm. or more. Four martensite cystals from four different ingots were prepared in this manner; the largest crystal of this group is illustrated in Fig. I. Back-reflection Lane patterns were obtained from martensite [ ] crystals (and the matrix austenite) both before and after tempering. The locations of the basal-plane pole of martensite was checked by means of oscillating crystal X-ray patterns. All four crystals studied yielded the same solution (±0.5°), and these relationships are expressed in gnomonic projection in Fig. 3.* The narrow dark-etching bands often visible in martensite "needles" were found to be parallel to {112} and thus are undoubtedly twin bands in the martensite crystal.

Jan 1, 1941

By W. J. Reagan

Many factors enter into the manufacture of basic open-hearth steel of high quality. Perhaps the two most important are temperature and the iron oxide content of the metal. If we can control these two factors we can essentially control basic open-hearth practice. SOURCE AND EFFECT OF IRON OXIDE Earlier investigators, especially Herty and his associates, have shown that iron oxide is introduced into the open-hearth furnace in four ways:' 1. By oxidation of the scrap by furnace gases. 2. By decomposition of the limestone. 3. By oxidation of the iron oxide in the slag by furnace gases. 4. By direct addition of iron ore to the charge. We also know that the speed of operation of an open-hearth furnace depends, for a given charge and given combustion conditions, on the rate at which iron oxide will diffuse from the slag into the metal. The rate of diffusion depends upon a number of variables, such as iron oxide content of the slag, slag viscosity, etc., which also depend upon the amount of iron oxide in the metal, amount of carbon present, temperature, and so forth. For a given carbon and a given temperature, the iron oxide content of the metal is in proportion to the iron oxide content of the slag. This fact can be easily verified by analysis of slag samples taken as described by Herty.2 It is preferable to take these samples just before deoxidetion. In killing the steel samples with aluminum it is desirable to use aluminum rod of 99 per cent purity; ordinary commercial aluminum rod with a purity of approximately 92 per cent is not satisfactory. In drilling these samples it is also essential to take the largest amount of drillings possible. This gives more accurate results because it eliminates spotty segregation of A12O3.

Jan 1, 1932

By K. V. S. Sastry, V. P. Mehrotra

A laboratory investigation was carried out to study the influence of asphalt, bentonite, and corn starch binders on the pelletization kinetics of coal fines and on the quality of the resulting pellets. Pellet quality was evaluated in term of the compression strength, impact resistance (drop test), abrasion resistance, and resistance to severe weather conditions. The amount of binder addition did not significantly influence the pellet growth kinetics. However, the pellet quality varied markedly depending upon the type and the amount of binder wed. Experimental results are explained on the basis of the mechanism of interaction between the coal particles and the binders. Of the three binders tested, corn starch proved to be the best in all respects but for the resistance to water penetration. Finally, a combination of corn starch (imparting strength) and asphalt emulsion (imparting resistance to water penetration) was found to yield the best quality coal pellets.

Jan 1, 1983

By Paul M. Tyler

HISTORICAL concepts of the economics of the glass-sand industry are changing rapidly. The greatly expanded demand for glass containers combined with higher freight rates on raw materials and manufactured products have induced a migration of glass factories toward densely populated centers and the creation of new standards of place value for sub- standard sand deposits. This migration has been facilitated by the construction of pipelines to bring cheaper natural gas and liquid fuel to large cities and may be further speeded by the adoption of modern mineral dressing methods to permit economical utilization of local raw materials. Our national resources of naturally high-grade 1 silica sand are abundant, but most of the best de- posits are situated so far from large centers of population that it now costs $3.00 to $5.00 a ton to carry the sand from the mine to the optimum site for a 1 factory making beverage bottles, scientific and electrical glassware, and miscellaneous blown and pressed ware for local markets. It follows that on the basis of freight savings alone it may be economical to use material from inferior deposits closer to the factory even though the f.o.b. cost of mining and treatment may be much high

Jan 1, 1950

By M. Amsterdam, F. Rothwarf, L. Muldawer

SILVER-cadmium near the composition AgCd shows three equilibrium phases. As with 13 brass, the high temperature phase is disordered body-centered cubic (8) and the low temperature phase has the ordered CsCl structure . However, there is an intermediate temperature phase which is hexagonal close-packed ((). In a recent paper, Speich and Mack' report on a study of the Ag-Cd eutectoid near the AgCd composition. Unfortunately, the phase diagram upon which they base some of their conclusions is incorrect. That diagram is taken from the Metals Handbook' and the error is that the 0 and ( phases have been interchanged. The Handbook gives the low temperature phase as hexagonal (designated 5) and the intermediate temperature phase as cubic ordered (designated . The error may be typographical or it may be one of confusion resulting from the use of 5, ,, and 0 for the intermediate phase in various papers. A careful search of the literature reveals that a number of authors have indicated the correct relative positions of the 13, 5, and 0 phases. The comprehensive work of Fraenkel and Wolf clearly stated that the high and the low temperature phases are either identical or are very similar. olander,' on the basis of electrochemical measurements, showed that the 13 phase is disordered and the 1 phase (designated 8" in his paper and in refs. 3 and 5) is ordered. Further work by Durrant5 using thermal and metallographic analyses provided a more precise phase diagram. A summary of these works was given by Hansen6 and shows the correct relative positions of the phases. Owen, Rogers, and Guthrie7 located correctly the upper two phases by X-ray diffraction. Their failure to find the low tem-

Jan 1, 1954

By R. P. Marshall, L. P. Costas

The solid solubility of lithium in aluminum was determined by two independent techniques, electrical resistivity and microhardness, and the results are in close agreement. The solubility limits X-ray diffraction studies of the intermetallic compound LiAl indicate that its composition is nearly independent of temperature when in equilibrium with the terminal solid solution of aluminum. THE investigation of the aluminum-rich portion of the aluminum-lithium system at the Savannah River Laboratory was prompted by the observation that over-aged alloys consistently differed from the equilibrium states predicted by the latest published diagrams. Chemical analyses of these alloys showed their impurity contents to be quite low; therefore, the results obtained should have very nearly coincided with true equilibrium. A survey of the literature disclosed that previous studies had been made with metallographicig or electrical resistivity methods,4'5 but that agreement between results and technique was poor as evidenced in Fig. 1, which also includes the present results for comparison. The discrepancies have been attributed to impurities,3 and this is undoubtedly true in the early work.1'4'5 The latest Studies,''~ conducted with starting materials of higher purity, employed metallographic analysis, a technique that is quite sensitive to local homogeneity and depends strongly on subjective interpretation. In the present work the problem of defining solubility limits was approached in two ways. The first measured a physical property, electrical resistivity, at the equilibrium temperature. The second, a micro-hardness characterization of a diffusion zone, is a room temperature evaluation of a mechanical property under conditions removed from equilibrium. A close correlation between two such basically different approaches would strongly justify confidence in the results. I) MEASUREMENT OF SOLUBILITY OF LITHIUM IN ALUMINUM BY ELECTRICAL RESISTIVITY Experimental Procedure. Alloys for electrical resistivity measurements were made by melting and

Jan 1, 1962

1938 ABERNATHY, G E Feb 6, 1948 Min & Met Apr 1948 1937 ADAMS, ARMY Aug 20, 1949 Min Eng Dec 1949 1946 ADDY, GEORGE E Sept 24, 1950 Min Eng July 1951 1920 ALDERSON, WILTON P Feb 1951 Min Eng Sept 1952 1896 ALDRICH, T H , JR May 24, 1950 Min Eng Aug 1950 1942 ALDRIDGE, LEONARD June 8, 1952Jrn Met Sept 1952 1919 ALLEN, ROLLAND C July 18, 1948 Min &Met Sept 1948 1950 ANDERSON, C P Unknown Min Eng Feb 1951 1937 ANDERSON, JOHN H May 10, 1950 Min Eng Aug 1950 1914 ANDERSON, L DOUGLASS Unknown Min Eng Nov 1951 1948 ANDRAU, E W K Oct 20, 1951 1936 ANDREWS, CHARLES B Apr 19, 1950 Min Eng June 1950 1918 ARMITAGE, PAUL June 28, 1949 Min Eng Oct 1949 1924 ARMSTRONG, PERCY A E Jan 23, 1949 Min Eng May 1949 1906 ARNOLD, CHARLES LE NEVE Aug 7, 1949 Min Eng Oct 1949 1945 ARNOLD, HAROLD S Aug 7, 1950 Min Eng Oct 1950 1936 ASH, JAMES E Dec 17. 1949 Min Eng Apr 1950

Jan 1, 1952

By Maynard O. Serbousek, James R. McVey

IS there a quick way of assessing the conditions of a newly exposed roof in a coal mine? This has always been a nagging question. The problem is that unless effective controls are established as soon as possible, it becomes extremely difficult to extract coal safely and economically from conventional underground milling operations. Until recently, little has been done to provide a means of measuring the structural behavior of a coal mine roof while the face advances during actual production. (In fact, most measurements have always been made after the fact or during a roof pull-down where the roof is actually caused to fail with no support.)

Jan 9, 1976

By D. H. Davis, I. Fatt

Oil bearing rocks, usually found at depths of 2,000 to 10,000 it, are elastically deformed by overburden pressure. Although the change in porosity with pressure in a number of example rock.: has been shown to be small, it was thought that overburden pressure might have a significant effect on permeability. This note presents results of an investigation to determine the magnitude of the change in permeabilty with pressure. In routine core analysis permeabilities are measured on rock samples which are not under overburden pressure. If permeablity measured in this way differs from permeabilities measured under overburden pressure, a systematic error is introduced into well productivity calculations. The experiments described in this report were made to determine the magnitude of the change and thus to give an estimate of the error introduced into the calculations. The error introduced by the neglect of the change in permeability when overburden pressure is removed may account for part of the difference between well productivity calculated from core analysis and the actual well productivity. The results obtained in this investigation have only quali-tative significance because of the difficulty in reproducing in the laboratory the stress conditions on the rock buried in the earth. The assumption which is usually made is that the rocks in the earth are under a uniform pressure equal to the weight per unit area of the vertical overburden column from the rock in question to the surface of the earth less the pressure of the liquid in the pores of the rock. For an overburden consisting of sandstones and shales (of assumed average specific gravity of 2.3) and for a liquid pressure equal to the pressure in a salt water column (of specific gravity 1.0) reaching from the rock to the surface, the resulting net pressure on the rock is approximately 0.56 psi per ft of depth. EXPERIMENTAL METHOD Clean, dry sandstone core plugs one in. in diameter and about three in. long were mounted in a copper foil jacket as shown in Fig. 3 or molded in a Lucite jacket as shown in Fig. 4. All cores except those labeled "2" in Fig. 1 and "8" in Fig. 2 were measured in the copper foil jacket. Cores "2" and "8" were measured in the Lucite jacket. The jacketed core was placed in a high pressure hydraulic bomb in which the liquid pressure outside the jacket could be raised to 15,000 psi. Flow lines from the core were brought out of the bomb through special fittings in the bomh head and connected to a laboratory type gas permeameter. Measurements were made with nitrogen gas; the maximum mean gas pressure in the core was 16.1 psia. RESULTS The specific permeability of sandstone decreases with in. crease in overburden pressure. Most of the decrease takes place over the range of zero to 3,000 psi overburden pressure. If the net pressure on the rock is assumed to be 0.56 psi per ft of depth as discussed above, 3,000 psi of overburden pressure is equivalent to about 5,000 ft of overburden. At 3,000 psi overburden pressure, the permeability of the eight sandstone core samples tested ranged from 59 to 89 per cent of the permeability without overburden pressure. Figs. 1 and 2 show the permeability reduction as a function of overburden pressure. The permeability of the eight cores without overburden pressure ranged from 4.35 md to 632 md; these permeabilities are listed in Figs. 1 and 2. REFERENCES 1. Carpenter and Spencer: "Measurements of Compressibility of Consolidated Oil Bearing Sands," U. S. Bureau of Mines, R.I. 3450, (1940). * * *

Jan 1, 1952

By E. C. Pechin

THE Lucy furnace, owned by Messrs. Carnegie, Kloman & Co., and located on the Alleghany River, on the outskirts of Pittsburgh, is a splendid modern furnace, 75 feet high, and 20 feet bosh. She had been working well on low grade ores of about 50 per cent., producing daily 68 to 75 tons. There was on stock 500 tons of Republic ore, one of the purest and best of the Lake Superior ores, averaging over 68 per cent. of iron, which had been procured for the purpose of making a trial for Bessemer iron. This was charged by itself, and Mr. Skelding, the founder, reports that he did not succeed in getting a single cast when it came down, before the furnace chilled from the hearth to the top of the boshes, some 25 feet. Every effort was made to save her, without avail, and the disagree-

Jan 1, 1874

By Edmund C. Pechin

The Lucy furnace, owned by Messrs. Carnegie, Kloman & Co., and located on the Alleghany River, on the outskirts of Pittsburgh, is a splendid modern furnace, 75 feet high, and 20 feet bosh. She had been working well on low grade ores of about 50 per cent., producing daily 68 to 75 tons. There was on stock 500 tons of Republic ore, one of the purest and best of the Lake Superior ores, averaging over 68 per cent. of iron, which had been procured for the purpose of making a trial for Bessemer iron. This was charged by itself, and Mr. Skelding, the founder, reports that he did not succeed in getting a single cast when it came down, before the furnace chilled from the hearth to the top of the boshes, some 25 feet. Every effort was made to save her, without avail, and the disagree-

Jan 1, 1912