Search Documents

By P. Chiotti, J. T. Mason

Metallographic, thermal, X-ray, and vapor-pressure data were employed in establishing the Ce-Zn phase diagram. Nine compounds and three eutectics were observed. The eutectic compositions in weight percent zinc and temperatures are 10 pct and 495"C, 37 pct and 795°C, and 56 pct and 810°C. Three of the compounds, CeZn, CeZnn, and CeZne.5, melt congru-ently at 825°, 87.505°, and 980°C, respectively; the other six compounds, CeZns, CeZns.67, CeZn4.5, CeZn5.25, CeZn,, and CeZnll, decompose peritectically at 820°, 840°, 870°, 885", 960°, and 795"C, respectively. The compound CeZn5.25 is an AB5 type with a small range of composition which lies on the zinc-rich side of the 1 to 5 stoichiometry. Zinc vapor-pressure data obtained by the dewpoint method were employed in calczilating the thermodynamic properties of both the liquid alloys and solid compounds. The data for the A critical review of the information available on the Ce-Zn system up to 1960 has been given by K. Gschneidner, Jr.' Of particular interest is the work by J. schramm2 who investigated the region between 55 and 100 wt pct Zn and reported a CeZn,, compound which decomposes peritectically at 785"C, a CeZn, compound which melts congruently at 972"C, and five temperature horizontals at 79@, 817", 840", liquid alloys were fitted to the relation from which the relation was obtained by integration. In these relations F XS is the excess partial molal free energy, N is atom fraction, and the constants c and d have the values c = (-22,000 + 7.0T) and d = 6171,000 + 74.0T). Relations for the standard free energy of formation for the solid compounds were derived from the data. At 973°K the enthalpy in kilocalories per gram-atom z)aries from —11.3 for CeZnz to —8.21 for CeZn~l and the free energy in the same units varies from —7.1 joy CeZn, to -3.82 for CeZn11. and 942°C in the region between 55 and 75 wt pct Zn. No attempt was made to identify other features of the system. I. Johnson and R. yonko3 used a fused-salt cell to measure the electromotive force between pure cerium and an alloy consisting of zinc-rich liquid in equilibrium with CeZnll. Solubility data for cerium in zinc has been reported by J. Knighton et u1 .4 Johnson and Yonko give the following equa-. tions for the mole fraction of cerium in zinc and the standard free energy of formation of CeZnll:

Jan 1, 1965

By L. Grånäs, B. Aronsson

In a recent study of Fe-Si alloys Walter and Koch' observed pairs of dislocations in Fe-6.25 pct Si crystals rolled to reductions of 10 pct and subsequently annealed for 1 hr at 650°C. They interpreted these pairs as being due to stacking faults. From the spacing of the dislocations a stacking-fault energy of 15 to 19 ergs per sq cm was calculated. These authors did not pay any attention to the order -disorder phenomena in Fe-Si alloys. It is the purpose of this communication to report some preliminary results from a study of ordering and its influence on the plastic deformation of Fe-6.0 pct Si alloys. Our results suggest that the dislocation pairs observed by Walter and Koch may have been due to long-range order rather than to stacking faults. The alloys used in this investigation were prepared from pure electrolytic iron and silicon and were melted in argon. After hot working, strip tensile specimens were machined to a gage length of 70 mm and a thickness of 1 mm. The specimens were heat- treated for 2 hr at 1000°C, furnace-cooled, and subsequently deformed 2 pct in tension at 400°C. The strain rate was 5.6 X lo-' sec-'. Thin foils of the deformed specimens were prepared by means of the Bollman technique and examined in a Siemens Elmis-kop I at an accelerating voltage of 100 kv. In the Fe-Si system long-range ordering occurs at a silicon content of about 6 pct Si. In our alloys evidence for ordering is given by selected-area diffraction patterns which show extra reflections consistent with a super lattice of the D0 9 type. In addition, the dislocation arrangement in deformed specimens indicates that long-range order is present. A typical mi-crophotograph of a thin foil is shown in Fig. l. The dislocations are usually straight and parallel and laying in distinct directions. In the commonly observed (111) zone the projections of the dislocations are close to (113) and (oil). Observation of the image position indicates that the two dislocations in a pair have the same Burgers vector and hence constitute a superlattice dislocation.~ According to theory3 a superlattice dislocation in the DO3 structure consists of four ordinary dislocations connected by two types of antiphase boundaries as shown in Fig. 2. In our specimens only two dislocations in each pair have been observed, Fig. 1. The problem is to decide whether the area between these is a NN or a NNN antiphase boundary. Dark-field images using the (200) reflexion (the indices are defined with respect to the DO3-type superlattice) can

Jan 1, 1968

By Richard P. Rothwell

The anthracite coals of Pennsylvania are all mined from large veins. A seam less than four feet. in thickness is generally considered as unworkable, those from which most of the coal now comes being from 8 'to 30 feet thick. The system of mining employed is, almost without exception, that known as " chamber and pillar work;" that is, the coal is taken out of chambers of from 18 to 30 feet in width, and pillars of from 12 to 20 feet are left between these to support the roof. In general, the entire thickness of the seam, even

By Fred C., Fred C. Bond

Comminution energy is principally energy of deformation before breakage, which appears as heat. An empirical equation is presented which covers the entire comminution range. The new strain-energy theory considers comminution from the known principles of mechanics and the reduction ratio. Energy requirements according to the different theories are compared.

Jan 1, 1950

By M. R. Geer, H. F. Yancey

0. R. LYONS*—I know that we are all interested in hearing about problems that other people have. To most of the people from the eastern part of the United States, this kind of coal preparation is completely different. It represents washing difficulties that most operators have never experienced, or, if they have, they have refused to consider them because there are coals that are much easier to wash and, therefore. they leave the more difficult ones alone for the time being. E. R. McMILLAN†—I think the au-thors have summarized the material very well. Dr. Yancey has spent a great many years in the study of washing coals, as has Mr. Geer. I might comment briefly on some of the plants that were mentioned, plants with which I have had some con-nection, particularly those of our own company, the Northwestern Improve-ment Co. I would like to point out this: that ill each case, a great deal of work was done in the way of preliminary studies of washability of the coal before plants were built. The first plant of any size built in Roslyn field was mentioned in the paper. This central cleaning plant was designed and built to handle coal from three different mines. I might say that prior to 1935, the year in which the plant was built, the coal was used largely as railway fuel, close to a million tons annually. But as mining increased in depth, it became increasingly difficult to separate and gob much of the impurities underground, with the result that the run-of-mine coal became so high in ash that the railroad eventually was forced to consider installing some kind of preparation plant at the mine. We spent about a year in preliminary studies in cooperation with the Bureau of Mines to find out the best type of plant that would clean the coal. The result, as Mr. Geer has explained to you, is a rather complicated plant, but it is doing a very satisfactory job. We have, however, made a number of changes and improve-n~euts since it was first built. The last addition was the, installation of a cen- trifugal drier to dewater the minus ¼ in. size. We are now contemplating installing heat driers for further drying of minus ¼ in. We use Vissac heat driers for drying the stoker coal, the ¾ to in. The demand for drier coal, for both railway and industrial use, is forcing us to further drying of the coal. The plant that was mentioned as having been built in Pierce County, during the war, was a government sponsored plant. I happen to have had some connection with its design, construction and initial operation. We did what we thought then, and still think, was a very thorough job of preliminary studies in cooperation with the Burea of Mines of the coal from that field. The plant was as good a plant as could be built with the equipment available at that time, 1943. The plant that was mentioned as having been built at Ravensdale for treating the McKay coal was rebuilt about two years ago, and in addition to the modified Elmore jig washer that was mentioned. we added a coucentrating table for re-cleaning the minus 3/32 in. Our object there was to produce a commercial

Jan 1, 1950

By Charles Fettke

IN 1914, the officials of the Brundred Oil Corpn., faced with the problem of introducing new methods to increase production in the old and nearly depleted pools of Venango County, became interested in the Smith-Dunn (Marietta) process which was at that time being tried out in southeastern Ohio and which was already yielding very encouraging results. A license to use the process in Pennsylvania was secured from the owners of the patents. These patents were later declared invalid. The method was first used in Pennsylvania on a property consisting of about 434 acres, of which 300 are productive, at Hamilton Corners, 15 miles northeast of Oil City, in Cherry Tree and Oakland Townships, Venango County. The producing horizon is the First Sand of the Venango Group. A small oil pool was opened up in this vicinity in 1904. By July, 1916, when the compressed air was first introduced to restore pressure, the production had dropped to a point where it was no longer possible to continue profitable operation. From that time until March, 1927, over 100,000 bbl. of oil have been recovered from the tract. The property is being operated at present by the Brundred Oil Corpn. and Lux. The 1926 production, amounting to 10,650 bbl., was only 400 bbl. short of the maximum reached during any year of the 10-year period that the process has been in operation. Inasmuch as the Hamilton Corners pool is the first one in Pennsylvania in which the Marietta process was tried out, and the one in which it has been longest in continuous operation, considerable interest attaches to the results obtained. Through the courtesy of H. D. Brown and W. J: Brundred, officials of the Brundred Oil Corpn., all their data on this operation were made available to the writer in connection with an investigation of rejuvenation methods in the State for the Pennsylvania Geological Survey.

Jan 1, 1928

By J. F. Enrietto

It is shown that one cannot approximate the broad internal friction Peaks observed in the Fe-Mn-N system as the sum of a number of subsidiary Peaks and still vetain the concept of a single relaxation time. Furthermore, the approximation of manganese affectirg only nearest neighbor interstitial sites is shown to be incompatible with the experimental results. The results of this experiment show that the influence of manganese in the ferrite lattice extends over 3 to 4 atomic distances. NUMEROUS experiments have shown that the presence of relatively small amounts of substitutional alloying elements can profoundly affect the profile of the damping spectrum in the vicinity of the Snoek peak in bee metals.1-7 Dijkstra and Sladekl observed this phenomenon in Fe-Mn-N alloys where it appeared as a broadening and shifting of the Snoek peak to higher temperatures. The authors interpreted this as being the result of a superposition of two damping maxima—the normal Snoek peak, located at its usual position and having a normal half-width, and an interaction peak having a normal half-width, but occurring at a somewhat higher temperature. They prclposed that the interaction peak was caused by nitrogen atoms jumping from Fe-Mn sites to Fe-Fe sites, the Fe-Mn interstitial sites having one manganese and one iron atom as nearest neighbors, and the Fe-Fe sites having two iron atoms as nearest neighbors. They further suggested that the Fe-Mn sites had a lower energy than the normal Fe-Fe sites because of the presence of the adjacent manganese atoms. From the relative heights of the two postulated damping peaks, the dif-

Jan 1, 1962

By L. G. Evans, C. Rampacek, G. A. Freeman

A large aggregate tonnage of oxidized and mixed oxide-sulfide copper ore of the southwestern U.S. is not amenable to conventional flotation concentration or sulfuric acid leach treatment. Most of the ores contain chrysocolla as the principal oxide copper mineral, for which no successful commercial flotation method has yet been developed. Acid leaching some ores is not feasible since they contain substantial quantities of calcite and other acid-consuming constituents. Other ores decrepitate during leaching or contain excessive slime and clay minerals which cause plugging of the ore beds.

Jan 10, 1961

By J. K. Buehler

With the rapid acceleration of the cost of shovel dippers and major standard shovel clipper rebuild components, maintenance management at Kennecott Copper Corp.'s Bingham Canyon mine initiated a dipper maintenance and rebuild program. The program focused on extending the service life of the shovel dipper, reducing field labor in maintaining dippers, and lowering shovel dipper rebuild costs. While comprehensive evaluation of the program is still underway, preliminary benefits of the program indicate: •Reduced field ,gelding for shovel dipper field maintenance, •Fewer dipper rebuild units entering the shop, and •Reduced dipper rebuild costs per unit.

Jan 1, 1979

By R. D. Pehlke, W. M. Small

The effect of added alloying elements on the solubility of nitrogen in a liquid alloy of 74 wt pct Fe. 18 wt pct Cr, and 8 wt pct Ni has been studied. At 1600°C and 1 atm nitrogen pressure, aluminum, chromium, columbium, manganese, molybdenum, tantalum, and vanadium increase the solubility of nitrogen in the liquid 18 Cr-8 Ni alloy, whereas additions of cobalt, copper, nickel, silicon, tin, and tungsten decrease the solubility. Interaction parameters based on a constant ratio of iron, chromium , and nickel have been used to quantitatively define the changes in nitrogen solubility. INVESTIGATIONS on the solubility of nitrogen in liquid iron have usually treated the pure metal, and often the influence of a single added element. Pehlke and Elliott1 carried out a comprehensive study on the influence of alloying elements on nitrogen solubility in liquid iron, and compared their results with previous studies. Turnock and pehlke2 have recently reported a study on the solubility of nitrogen in multicomponent liquid iron alloys. The original interaction parameter proposed by wagner3 was successfully employed in these studies. The need for obtaining information on the gas solubility in more complex alloys is indicated by the increasingly significant role played by dissolved gases in the processing of iron-based materials. The commercial stainless steels, for example, represent an area where data on nitrogen solubilities are required as a function of composition, temperature, and gas pressure. The nitrogen solubility in liquid Fe-Cr-Ni alloys has been studied by Humbert and Elliott.4 Their investigation covered the entire ternary system, and attempted to use data from binary alloys to predict nitrogen contents in liquid ternary alloys. Langenberg,5 using a method developed by Morris and buehl,6 calculated the nitrogen solubilities in multicomponent iron alloys from data available on binary iron alloys at 1600°C. Nelson,7 using a regular-solution model, extended this prediction to include the effect of temperature. Chipman and corrigan8 and Turnock and pehlke2 also employed empirical methods to calculate nitrogen solubilities in liquid multicomponent iron alloys. In order to provide a basis for predicting nitrogen solubility in liquid stainless steels, and to extend the data available for thermochemically modeling systems of this type, the following investigation was carried out. The study involved measupements of nitrogen solubility in a nondilute alloy and examination of the influence of a small addition of an alloying element on the nitrogen solubility. The study was focused on a very narrow range Of composition in the vicinity of 18 wt pct Cr-8 wt pct Ni (herein referred to as 18-8) with special emphasis on the change of.nitrogen solubility with the addition of a fourth metallic element. EXPERIMENTAL PROCEDURE A Sieverts' apparatus, described previously,1,2 was used in this investigation. The charge materials were contained in a recrystallized alumina crucible and inductively melted. Additions were dropped from a glass side-arm. All materials were hydrogen-refined and vacuum-treated to eliminate or minimize the oxygen content. The source and purity of materials is given in Table I. The initial metallic charge was heated to approximately 1000°C and held under vacuum for 30 to 45 min as a means for removing hydrogen and adsorbed gases. Argon was used as the calibrating gas to determine the "hot volume". The average hot volume of the system was approximately 50 cu cm STP and a few experimental runs were made using a reaction bulb with a hot volume of 80 cu cm. The temperature range studied was from 1550° to 1700°C and the temperature was measured optically. THEORETICAL PRINCIPLES General Discussion. Nitrogen dissolves in liquid iron alloys according to the reaction: 1/2N2(g) = N (wt pct in solution) [l] The equilibrium constant, K1, for this reaction is written as:

Jan 1, 1969

By R. L. Smith, J. L. Rutherford

ALTHOUGH considerable effort has been devoted toward the determination of the mechanical properties of pure metals, it is extremely difficult to compare the results of such work. This is because of differences in method and type of test, grain size, heat treatment, and purity of material. There is very little information on the properties of most of the high melting point reactive metals with purities greater than 99.9 pct. Previous evidence concerning the tensile properties of unalloyed metals show that: body-centered-cubic metals are brittle at low temperatures; face-centered-cubic metals remain ductile; some hexagonal metals remain ductile, others become brittle. It may be that traces of impurities decrease the low temperature ductility of the body-centered-cubic lattice. This would suppose that a body-centered-cubic lattice free from impurities would exhibit nearly the same ductility as a face-centered-cubic structure. The present investigation has been an evaluation of the tensile properties of zone refined iron in order to determine whether higher purity material than that previously evaluated behaves differently. Experimental Procedure In this investigation, high purity iron was zone purified using the floating zone method.' The starting stock was obtained from two sources. The first,

Jan 1, 1958

By H. A. Guess

For a number of years I have used for the commercial wet assay of lead generally the ammonium molydate, and occa-sionally the ferrocyanide method. These well-known methods need no detailed description here. In the ore-selling and ore-buying establiahments of the West, 90 per cent. of all wet lead-assays are made by one or the other, and at least nine-tenths of this proportion by the molybdate method. A procedure so well-established must have merit; and, in

Jan 1, 1905

By D. H. Bacon

Our Transactions contain so many suggestions of apparently trivial, yet really important, contrivances for the saving of time and

Jan 1, 1893

By T. T. Read

JAPAN'S iron and steel industry has always been closely connected with military strategy. Many years ago it became evident that the country's iron-ore resources were too small to support any extensive industry. As a result a belief in the imperative necessity of securing such resources has influenced Japan's political and economic policy in the Far East. Iron-ore developments in China are too well known to need repeating except to note that they have been rather unsatisfactory to both China and Japan. The ore deposit at Tayeh, in China, is not as large as was first believed and, though that and other sources of supply in China proper are now furnishing Japan a little more than a million tons of ore yearly, it cannot be counted upon as a large permanent source of supply. The deposit in Shantung proved so disappointing on further exploration that operations there have, so far as I know, long since ended. The operations at Pen-bsi-hu, in South Manchuria, which C. F. Wang de¬scribed in the A.I.M.E. TRANSACTIONS for 1918, Vol. 59, were reported to have yielded 84,000 tons of pig iron in 1928 and about 50,000 in 1935, so they seem to be going back.

Jan 1, 1937

By GEORGE O. SUMAN

IN THE operation of oil properties there are various difficulties with pumping wells which can often be overcome or greatly lessened if sufficient attention is, directed towards pump and tubing problems. The difficulties referred to are the wearing out of pumps, sanding up of pumps, and the sanding up of the hole. As the perforations in the oil strings are large and the oil and sand loose and unconsolidated considerable trouble is often encountered in pumping wells due to the ease with which' the sand can come into the holes. DETERMINING FLUID LEVEL In determining the proper depth at which to tube a well it is essential to first find out something about the behavior of the fluid in 'the hole: Facts in regard to this natter can be obtained by finding the fluid level on pulling the tubing, by making a pumping test on the well tubed to various depths, and by bailing tests during cleaning out work. In ordinary oil field operations it is customary to take the fluid level at the time of pulling the tubing. This 'can only be done when the pump is not sanded up. There are two methods used in obtaining the fluid level. One method is to note where the outside of the tubing starts, to be covered with fluid when pulling the

Jan 1, 1925

By V. H. Wilhelm

In contrast with the previous year's activity, the California oil industry for 1938 showed a decrease in drilling, market demand, and discovery of new oil reserves, although there was an increase in oil production. Although additions to reserves from new fields and extensions were less than withdrawals during the year, reappraisals of discoveries in 1937 added to new discoreries during 1938 amounted to over 300,000,000 bbl. The following comparative statement shows the important changes in various phases of the industry: Throughout the year the storage situation became progressively more acute, owing principally to less Pacific foreign demand, and increased potential from drilling the newly discovered fields and pools (Fig. 1). California storage increased approximately 32,000,000 bbl. during 1938, most of which (approximately 18,000,000 bbl.) was heavy crude and residuum. The market demand for the year was around 600,000 bbl. per day. Because of the trend toward Diesel power for heavy transportation, the non-gasoline-bearing crudes arc fast becoming a drug on the market. New discoveries were instrumental in increasing the potential production of the state from 1,076,000 bbl. per day in January to an all-time high of 1,420,000 bbl. per day at the close of the year; although the indicated reserves of these new discoveries were not equal to the yearly withdrawal of 249,000,000 bbl. As of the end of 1938, the state was voluntarily curtailed about 58 per cent. As a result of prospecting during the year, six new fields were discovered, three fields were extended, and deeper zones were reached in five of the older fields.

Jan 1, 1939

By V. H. Wilhelm

In contrast with the previous year's activity, the California oil industry for 1938 showed a decrease in drilling, market demand, and discovery of new oil reserves, although there was an increase in oil production. Although additions to reserves from new fields and extensions were less than withdrawals during the year, reappraisals of discoveries in 1937 added to new discoreries during 1938 amounted to over 300,000,000 bbl. The following comparative statement shows the important changes in various phases of the industry: Throughout the year the storage situation became progressively more acute, owing principally to less Pacific foreign demand, and increased potential from drilling the newly discovered fields and pools (Fig. 1). California storage increased approximately 32,000,000 bbl. during 1938, most of which (approximately 18,000,000 bbl.) was heavy crude and residuum. The market demand for the year was around 600,000 bbl. per day. Because of the trend toward Diesel power for heavy transportation, the non-gasoline-bearing crudes arc fast becoming a drug on the market. New discoveries were instrumental in increasing the potential production of the state from 1,076,000 bbl. per day in January to an all-time high of 1,420,000 bbl. per day at the close of the year; although the indicated reserves of these new discoveries were not equal to the yearly withdrawal of 249,000,000 bbl. As of the end of 1938, the state was voluntarily curtailed about 58 per cent. As a result of prospecting during the year, six new fields were discovered, three fields were extended, and deeper zones were reached in five of the older fields.

Jan 1, 1939

By A. L. Jr. Pozzi, A. O. Garder, D. W. Peaceman

A new numerical method is proposed for the solution of multidimensional miscible displacement problems. Besides the usual stationary grid associated with numerical procedures, the method uses moving points for which positions and concentrations are computed each time step. Based on the method of characteristics for treating combined transport and dispersion, the method applies equally well to any number of dimensions and, in contrast with other numerical procedures, properly takes into account the physical dispersion, no matter how small. Extensive tests show that accurate solutions of one-dimensional problems can be obtained over a wide range of values of the dispersion coefficient, including zero. They also show that the moving points do not need to be uniformly spaced, and that increasing the number of moving points beyond 2/grid interval does not significantly improve the accuracy of the solution. Two-dimmsional calculations using the new method were carried out to simulate laboratory model displacements in which gravity caused overriding of solvent. Good agreement between observed and computed profiles and measured and computed concentrations of produced fluid was obtained for a viscosity ratio of 1.89; at higher viscosity ratios, fair agreement was obtained Computed results were found to be significantly affected by vertical dispersion, and negligibly affected by dispersion in the direction of flow, in agreement with conclusions based on experimental observations. INTRODUCTION Although miscible displacement processes are potentially of great economic significance, limited progress has been made in developing mathematical methods for predicting the outcome of a solvent flood. Because of the complexity of the partial differential equations which describe multidimensional miscible displacement, numerical methods are a natural approach to their solution. The task of finding suitable numerical approximations to one of the partial differential equations, which involves both dispersion and convective transport, has been particularly difficult. Dispersion in the absence of transport is described by the heat flow equation, a second-order equation of parabolic type. This equation has been very successfully treated by numerical methods. Transport in the absence of dispersion is described by a first-order equation of hyperbolic type. This equation has been treated numerically with some success in one dimension, both by Lagrangian and Eulerian techniques, 1.2 but extension to two or more dimensions has not been satisfactorily accomplished. Usually one of two things happens: either the numerical solution develops oscillations or it becomes smeared by artificial dispersion resulting from the numerical process. When transport and dispersion are considered simultaneously, this numerical dispersion may dominate the low physical dispersivicy that generally characterizes miscible displacement. Stone and Brian2 have developed a new difference equation for treating combined transport and dispersion in one dimension. By suitable choice of certain parameters, they succeeded in markedly reducing both oscillation and numerical dispersion. However, a satisfactory extension to higher dimensions has not yet been found. Peaceman and Rachford3 presented a centered-in-time and centered-in-distance difference equation combined with a 1,transfer of overshoot" procedure which was demonstrated to work well in one dimension. The technique was applied to the two-dimensional miscible displacement problem, but subsequent calculations with zero dispersivity showed little change in results compared with the calculations they presented. This indicates that their method involved a numerical dispersion of the same order as the physical dispersion. The present paper describes an alternate method for solving the combined transport-dispersion

Jan 1, 1965

By Cyril Smith

ALTHOUGH not of the same importance as electrical conductivity, the capacity for conducting heat is nevertheless a very important property of metals and alloys. A knowledge of thermal conductivity is of value in selecting alloys for many purposes and in the calculation of the efficiency of apparatus which is being designed. Unfortunately, the determination of thermal conductivity is extremely slow and tedious, consequently few data have been obtained. A further reason for the lack of information is that there has long been an impression that the thermal conductivity of an alloy is directly proportional to the electrical conductivity and that it can therefore be calculated from the latter. The Wiedemann-Franz-Lorenz law of constant ratio of the two conductivities holds with a considerable degree of precision for all the pure metals, but appreciable deviations occur in certain alloys-particularly those containing nickel-and it seems difficult to predict exactly what the ratio will be. Therefore direct determinations of thermal conductivity should be made whenever the results are, needed with any accuracy. This research is intended eventually to cover all the alloys of copper that are of commercial importance, including the binary alloys of copper with zinc, tin, aluminum, nickel, silicon, manganese, cadmium and phosphorus, and the ternary alloys copper-nickel-zinc, copper-nickel-silicon, copper-manganese-silicon, copper-zinc-tin, etc. Most of these alloys are customarily used in the wrought condition and therefore were tested in the form of annealed rods. A limited number of sand castings were also obtained and examined. This paper contains a complete review of all the previous work that has been done on copper alloys, and includes a detailed description of the apparatus and method of procedure used in the present research, together with the new results obtained on the copper-zinc series, which is the only one completed at the present time. Subsequent papers describing the other alloys will contain the experimental results and discussion only.

Jan 1, 1930

By W. C. PAGE

AS the pioneer operation treating the mixed lead- zinc-iron ores from the district tributary to the Salt Lake Valley, the International Smelting Co.'s plant has offered an extremely interesting and instructive opportunity to study some phases of this problem. Basically, there were two main reason for our attempting to work out a successful operation for the separation and concentration of the values contained in the rather widespread deposits of these so- called lead-zinc ores. In the first place, the time was ripe and demanded some method of curtailing the economic waste resulting from the costs of past and present practice of smelting ores of this character, or rather, those ores which could stand the charges inherent with smelting them. Secondly, but rather primarily with us, we believe that such a solution would greatly in- crease in general the production of lead in the district tributary to the Salt Lake Valley. It is generally known that there were and are three relatively large lead smelting plants in the Salt Lake Valley and the decreasing production of correspondingly clean lead ores was not efficient to justify the existence of all three. We could not hope for better lead smelting metallurgy nor more efficient business management than was being practised, so the only prospect was to at- tempt to work out some way to increase the primary production and thus widen the scope of operations.

Jan 1, 1926