Search Documents

By C. G. Brehm

THE anthracite-producing region is in the northeastern section of Pennsylvania, and has an area of approximately 484 square miles. It is divided geographically into three separate fields, known as the Northern, Middle and Southern. The Northern field, with Wilkes-Barre approximately at its center, is a basin about 60 miles long and almost 6 miles wide at its greatest distance across. Generally speaking, it may be said that the coal meas-ures in this field lie horizontally, or on slight pitches, and consist of from 11 to 19 veins of coal, varying in thickness from several inches to several feet. The intervening strata between veins may be composed of slate, clay, rock or shale, or a combination of several, and are sometimes very thin. This condition often causes a treacherous roof, therefore roof sup-port and the attending hazard of mining are problems of concern. The Middle field is made up of a number of small basins of not very great depth, and the measures, which are in like number to those of the Northern field, are varying inclinations running from nearly flat to steep pitches.

Jan 1, 1938

NEW MEMBERS The following list comprises the names of those persons who became members during the period Oct. 10, 1918, to Nov. 9, 1918. ALLER, FRANK D., Copper Met., Ore Purchaser, American Smelt. & Refin. Co., 120 Broadway, New York, N. Y. AVÈRY, PAUL W., Met. Engr., Esperanza Min. Co., Apt. 8, El Oro, Mex., Mexico. BAKER, CHARLES A., Leaching Foreman, Copper Leaching Plant, Anaconda Copper Min. Co., Anaconda, Mont: BREED, CHARLES H Met., Crown Cork & Seal Co., Baltimore, Md. CHASE, R. L., Min. Engr 102S First National Bank Bldg., Denver, Colo. EICHELBERGER, FRANK, Vice-pres. and Engr., New York-Montana Testing & Engrg. Co., Helena, Mont. GESTER, G. C., Geol., Standard Oil Co. of Cal., 616 Standard Oil Bldg., San Francisco, Cal. GRIFFIN, JOHN, Mgr., Anthracite Territory, The Dorr Co., Board of Trade Bldg., Scranton, Pa. HAYNES, ELWOOD Pres., The Haynes Stellite Co., Kokomo, Indiana. Hsi, T. C:.. Sec'y, Tayeh Iron & Steel Works, Tayeh, China. HYDE, AUSTIN T., Mgr., Keokuk Plant, River Smelt. & Refin. Co., 607 Franklin St., Keokuk, Iowa.

Jan 12, 1918

THE opening session* was held in the hall of the Franklin Institute, on Tuesday evening, June 20th, President Holley in the chair. The President introduced. Mr. Franklin B. Gowen, who addressed the Institute as follows MR. PRESIDENT AND GENTLEMEN : It has been made my pleasant duty to welcome you to the city of Philadelphia, but in so doing I shrink, with some natural reluctance, from appearing before an audience so much better fitted than I am to cope with the subjects which are usually presented to your association, and I can assure you that no trembling neophyte, first venturing within the groves of the Academy, or walking, with sacred reverence, in the gardens of Plato, felt more natural dread at the consequence of his own temerity than I do in appearing before an audience composed of gentlemen belonging to a scientific society of which I am but too sensible that until now I have been a member only in name. In olden times, upon entering a temple sacred to the worship of any deity, it was customary to lay some offering upon the altar, and, in following this custom, it will be my duty, before entering upon the more pleasant part of the task which is assigned me, to call your attention to a subject with which I have been somewhat familiar, and which is entirely within the scope of your investigations, in the belief that I may throw out some hints or some suggestions of a pro¬cess that may be fully developed by some of you, and eventually lead to the introduction of that which may be of service to the human race. The satirist who described the philosopher whom he met, as engaged in the process of extracting sunbeams from cucumbers, * A joint discussion of the subject of Technical Education, by the members of the American Society of Civil Engineers and the American Institute of Mining Engineers, was held in the hall of the Franklin Institute, on Monday evening, June 19th, and Tuesday morning, June 20th. This discussion has been printed in a separate pamphlet by both societies.

Jan 1, 1877

By RUSSELL C. FLEMING

THE important advances that have been made of recent years in mining and milling methods and in mechanical equipment at mines need no re- telling, but there has been a remarkable growth in one type of equipment which has gone nearly unnoticed. That is the increasing use of storage-battery locomotives underground. Since the war the number of these locomotives and their field of use have increased tremendously; their growing acceptance represents an al- most complete reversal of opinion from an earlier period when they were generally looked upon as in- adequate for the strain of mine service. At the time when storage-battery powered units were first making their bid for recognition, the use of power in haulage had already passed through several phases; hand tramming, rope haulage, compressed air locomotives, even gasoline locomotives, had all been used, ending finally in the general adoption of the electric trolley locomotive for practically all power-haulage requirements. It was, and is, conceded that the trolley loco- motive met more adequately the varied and severe conditions of mine service than any previous type of haul- age unit. Subsequent developments have had to endure comparison and surpass in performance that type of haulage before changes would be considered.

Jan 1, 1930

Jan 1, 1933

By E. H. Citron

CLEANING fine coal in jigs is not new in Europe, where the feldspar jig is being used almost exclusively for this purpose. A feldspar jig operates with an artificial bed made up generally of feldspar or other hard rock material. Dimensions and specific gravity of this material must be of suitable values for good bedding qualities. For good efficiency, the size should range between 1x2 in. and 2x2x½ in. thick. The disadvantage of an artificial bed is that it is not mobile and must be replaced every so often with new material to obtain good cleavage characteristics. A semi-mobile bed has been developed to retain only a part of the feldspar on the sieve screen— the other part is drawn off with the refuse material, from which it is reclaimed and returned to the jig feed. Recirculating this feldspar rock offers definite advantages. However, in time it will lose its original shape because of wear, and new bed material must be added to the jig feed. The latest feldspar jigs arc generally air-pulsated, Baum-type jigs, although more than 70 pct of the feldspar jigs operating in Continental Europe are still of the piston type. These jigs are very popular in Europe, but they do require a great deal of time and attention. New Theory to Eliminate Artificial Bedding: At the preparation plants of Pittsburg & Midway Coal Mining Co. it has always been the contention that a small piston-type jig could be developed to clean fine 1/4x0-in. coal down to 28 to 60 mesh efficiently by obtaining and admitting bedding material from the present plant refuse circuit to the jig feed. This eliminates use of artificial bedding materials. The jig should incorporate these essential adjustable features as follows: Adjustable Sieve Screen A screen that can be raised and lowered to increase or decrease washing compartment depth. The sieve screen also can be set on an incline level, or decline. Adjustable Plunger Eccentric Length of stroke can be adjusted to increase or decrease pulsion and suction. Variable Plunger Speed Variable speed reducer for decreasing and increasing the number of strokes per minute. Water Distribution Adjustable baffle plate separating the plunger and sieve compartment so the water can be distributed uniformly over the entire sieve screen area. Refuse Ejector Special unique rubber-type refuse ejector gate operated by air and electrically controlled (as a conventional jig). Automatic Control Conventional float that measures the specific gravity of the coal-water refuse medium in the jig is of the submerged type. The float is mounted on a vertical stem held in position by two parallel arms. A movable weight regulates the effective specific gravity of the float. The float stem can be raised and lowered, having a graduated scale to indicate the depth of bed for the setting of the float. Hutch Drawoff Hutch material is drawn from the cell compartment to the elevator compartment by gravity. The first one-cell experimental jig incorporating all these features was built in January 1955 by Ore

Jan 1, 1959

By H. Foster Bain

(San Francisco Meeting, October, 1911.) [SECRETARY'S NOTE.-This paper, presented in oral abstract, at the San Francisco meeting, was not at first supposed by Mr. Bain to be required for publication in the Transactions; and the excursion to Japan, in which he took part, immediately after the San Francisco meeting, delayed his presentation of the manuscript. After his return to San Francisco, Mr. Bain, in view of the importance of his paper and its discussion, kindly furnished it in full. The delay in its publication (since it was received in April last) has been due, partly to the circumstance that other contributions had meanwhile acquired the "right of way," and partly to the consideration that, the situation contemplated in Mr. Bain's paper having remained practically unchanged, the paper and its discussion would not lose force or timeliness by this lapse of time.-J. S.] No acute observer of public affairs can have failed to observe a growing disposition on the part of the public to change emphasis in government from political equality to social justice. When our own government was founded it was felt to be sufficient to secure to each individual the fullest possible freedom of opportunity, and such a scheme was excellently adapted to the rapid development of a large territory having a small population. As the number of people in a given area increases, there are more points of contact and conflict; each must move in a smaller orbit, and there must be more regulation. Germany is making faster progress in industry than is any other country. The principal reason is the insistence there on team-play. In Germany there are fewer multimillionaires and more socialists (spelled with either a big or little " S ") than in any other of the leading countries; but Germany wins trade and is steadily improving the conditions of life for her citizens. To some, the change from the freest individualism is welcome; to others it is intensely unacceptable. To this fundamental difference in view-point may be imputed much of the vigor with which the controversy regarding coal-lands has been waged. That present conditions in Alaskan coal-fields are extremely unsatisfactory is generally recognized, but there are wide dif-

Aug 1, 1912

By Messervey, J. P.

NOVA SCOTIA is sharing in the rapid advance of the mining industry that is one of the remark- able features of Canada's recent progress. The production of coal and gypsum has increased rapidly, and there has also been a marked development in the mining of gold, salt, zinc, copper and other minerals. Coal, the basis of the principal mining industry in the Province, was discovered by the early explorers on the shore of Cape Breton Island, and used by the garrison at Halifax as early as 1749. The first government record shows total annual sales amounting to 1668 long tons in the year 1785, while last year production was 6,643,000 long tons. The principal mines are discussed in a separate paper by Alexander L. Hay1.

Jan 1, 1928

The following Nominating Committee having been already appointed and approved by the Executive Committee in accordance with authority vested in the Executive Committee by the Board of Directors, was approved by the Directors: John V. N. Dorr, Chairman, Percy G. Beckett, J. W. Hutchinson, Julian Kennedy, William H. Linney, Charles W. Merrill, and E. Gybbon Spilsbury. The question of the purchase of Liberty Bonds, as well as that of bringing to the attention of the members the advisability of the purchase of these bonds, was referred to the Finance Committee. Sixty Members, four Associates, and thirty-six Junior Members were elected. Two Members were reinstated. Eight resignations were accepted.

Jan 7, 1917

By E. R. Parker, C. F. Riisness

That grain size has a great effect on the mechanical properties of metals has been recognized for a long time. Bassett and Davis1 in 1919 did excellent work in determining the effect of grain size on the hardness of brass. About the same time Jeffries2 and Sykes3 ascertained the effect of grain size on the strength and ductility of several metals at temperatures ranging from 80°K. to their melting points. When creep was recognized as an important property of metals, those engaged in the study of this property tried to determine the effect of grain size4-9 on creep rates. Unfortunately, most of the investigations were conducted on only two grain sizes, often designated simply as "fine" and "coarse." It is well known that at high temperatures coarse-grained test bars creep less than fine-grained bars. The relation between grain size and size of test bar, however, has been frequently overlooked. In his early work, Jeffries2 showed that the number of grains in the cross section has a more important influence on the properties of the material than the actual grain size. More recently Hanson and Sandfordl0 and Pell-Walpole,ll in their measurements of the creep and tensile properties of tin, tested a wide range of grain sizes and correlated the grain size with the strength. Hanson9 later established the relation between the number of grains in the cross section and the creep rate. At high temperatures, generally a coarsegrained structure is considered superior in creep to a fine-grained structure, but it is evident that for a given bar size continuously increasing the grain size will

Jan 1, 1944

By C. F. Riisness, E. R. Parker

That grain size has a great effect on the mechanical properties of metals has been recognized for a long time. Bassett and Davis1 in 1919 did excellent work in determining the effect of grain size on the hardness of brass. About the same time Jeffries2 and Sykes3 ascertained the effect of grain size on the strength and ductility of several metals at temperatures ranging from 80°K. to their melting points. When creep was recognized as an important property of metals, those engaged in the study of this property tried to determine the effect of grain size4-9 on creep rates. Unfortunately, most of the investigations were conducted on only two grain sizes, often designated simply as "fine" and "coarse." It is well known that at high temperatures coarse-grained test bars creep less than fine-grained bars. The relation between grain size and size of test bar, however, has been frequently overlooked. In his early work, Jeffries2 showed that the number of grains in the cross section has a more important influence on the properties of the material than the actual grain size. More recently Hanson and Sandfordl0 and Pell-Walpole,ll in their measurements of the creep and tensile properties of tin, tested a wide range of grain sizes and correlated the grain size with the strength. Hanson9 later established the relation between the number of grains in the cross section and the creep rate. At high temperatures, generally a coarsegrained structure is considered superior in creep to a fine-grained structure, but it is evident that for a given bar size continuously increasing the grain size will

Jan 1, 1944

By R. D. Reiswig, J. M. Dickinson

The 0s-Ir equilibrium diagram was determined. The diagram is of the simple peritectic type, with a peritectic temperature of about 2660°C. The solid miscibility gap is narrower than previously reported, the nearly vertical solvus lines occurring at about 42 and 63 wt pct 0s. Widmanstaetten figures resembling martensite in some of the two-phase alloys account for a previously suspected transformation. In view of the long history of use of such alloys, it is surprising that the 0s-Ir equilibrium diagram has not yet been completely determined. The boundaries of the miscibility gap in this system have been estimated to be between 24 and 39 wt pct 0s and 79 and 100 wt pct OS. It has been predicted3 that alloys of ruthenium, osmium, and rhenium with the fcc platinum metals should solidify peritectically in their two-phase regions. The metallographic examination of natural osmiridium alloys has been said4 to indicate, by the presence of a martensitic structure, the existence of a transformation or a phase separation. On the basis of superconducting transition temperature measurements, a 70 at. pct 0s alloy was found5 to be two-phase prior to annealing. EXPERIMENTAL The elemental components used in this work were obtained from several suppliers as sponge. The purities, stated by each supplier to be in excess of 99.8 pct, were confirmed in each case by a semiquantitative spectrographic analysis. The pure components were premelted in an inert-gas tungsten arc furnace with the evolution of some fume, crushed, and pickled for use as alloy melting stock. Upon arc melting to the final compositions, no fume evolution was observed. Because weight losses of the order of 15 mg or less were observed in preparing alloy buttons weighing 15 g, "synthetic analyses" were used in determining the compositions of the alloys. Alloys used in this investigation contained 15, 20, 33, 40, 42, 43, 45, 50, 55, 60, 63, 64, 66, 70, 79, and 80 wt pct 0s. Heat treatments of the alloy buttons and pieces thereof were performed in a previously described6 tungsten tube furnace under pressures of 105 torr or less. It was found that homogenization treatments on the specimens were essential to remove the severe coring which was present, a 3-hr treatment above 2300°C removing all the metallographi-cally visible evidence of coring. Following the various heat treatments, the specimens were "vacuum-quenched" by melting a tungsten fuse wire and allowing them to drop onto a water-cooled copper plate. In a few instances, specimens were quenched into molten tin for comparison, but no difference was apparent. Vacuum-quenched specimens cooled from 2400°C to below a red heat in less than 60 sec. Typical equilibration times varied from 3 hr above 2300°C to 88 hr near 1100°C. The utilization of successively longer equilibration times and the approach to equilibrium from both directions indicated that the times used were sufficient to give a close approach to true equilibrium. Heat-treatment temperatures were measured with a calibrated Leeds and Northrup optical pyrometer through a 0.120-in. lateral sight hole in the tungsten heater tube. It was known that the assumption of black-body conditions inside the 1-in.-diam by 10-in.-long tube was unwarranted. The empirical results of work with thermocouples and melting

Jan 1, 1964

By Haley, D. F.

WHEN operations were first started at Climax in 1917 by the Climax Molybdenum Co., they were pioneering in the molybdenum industry for little was known relative to the uses of molybdenum or the metallurgy of molybdenite concentration. Concentration of molybdenite is relatively simple today but in 1916, when the Climax deposit first attracted attention, it presented serious difficulties. Little was known, in fact, even about the assaying of such low-grade molybdenum ores. Mine samples were sent to at least a dozen of the best laboratories in the United States and average values reported varied from 0.4 per cent to 1.0 per cent MOS2. Owing to the wide variations in MoS2 content obtained from reliable chemists, the actual value of the ore was most uncertain. This variation occurred repeat¬edly over a period of six months in 1917. It was finally decided, as a last resort, to cut several tons of sample from the tunnel and have a mill test made, using the recovered MoS2 per ton as the grade of the ore, for a small error in the assaying of the concentrate would not materially affect the results. These mill tests were made by the General Engineering Co. (Callow) at Salt Lake City. The results proved an ore of commercial grade and indicated the flotation process for the best metallurgy. Based upon these tests, the decision was made to build a 200-ton flotation plant. At this time, the art of flotation was

Jan 1, 1946

By Robert J. De Angelis, James H. Barker

An improved method for solving dynawzical dislocation problems using a digital computer is described in this paper. Interactions between two distinct types of dislocations were studied: attractive screw dislocations; and Lomer lock forming dislocations. One dislocation is positioned in the lattice and is initially at rest, while the other dislocation is moved through the lattice on an intersecting slip plane at a constant velocity in the range 0.5 to 0.999C. (C is the transverse velocity of sound.) The results obtained from these computations indicate that screw dislocations account for a small fraction of the total strain over a wide portion of the range of velocities studied. They further indicate that mixed dislocations mainly repel other dislocations in the neighborhood of the active glide plane. From this a possible explanation for cell formation is put forth. The density of Lomer locks expected to exist after a strain of 0.2 was found to be 1.4 x 106 cm-2 which is in good agreement with indirect experimental estimates. IN the past, predictions of favorable or nonfavorable dislocation reactions were based on the associated changes in elastic strain energy. Such considerations take no account of the probability of the two dislocations coming into contact to react. Venables1 was the first to approach these probabilities by considering the interactions between two moving screw dislocations on perpendicular glide planes. Because of the restrictive types of dislocations and glide plane geometry employed, his results have limited application to metallic crystals. The work to be presented here develops a general approach to solving dynamical dislocation problems; either dislocation-dislocation interactions, presented here in detail, or dislocation interactions with any other suitably defined stress field. Two types of dislocation-dislocation interactions common to face centered cubic (fee) materials are considered: those between pure screw dislocations of opposite sign on intersecting slip planes and those between mixed dislocations on intersecting slip planes, that can react to form a perfect dislocation. This latter reaction, referred to as the Lomer reaction, produces a locked product dislocation that finds it energitical favorable to disassociate into two Shockley partials and a stair-rod dislocation. This partial configuration known as a Lomer-Cottrell (L-C) lock plays a major role in work hardening of fee crystals. seeger2 names the L-C lock as the prime contributor to Stage II hardening while Kuhlmann-wilsdorf3 and Meakin and Wils- dorf4 also state that it is a significant contributor to work hardening. However, with a few notable exceptions,5-7 direct observations of the Lomer lock and the L-C lock by electron transmission microscopy are scanty, and even these are subject to other interpretations.5,6 In a study of partial dislocations present in austenitic stainless steel, whelan8 did not observe any L-C locks at the head of pile-up groups. This result contradicted existing work hardening theories and led him to postulate an alternate theory based on the stress required to break away dislocations intersecting a pile-up group, from their stacking fault nodes. Due to the importance of the Lomer reaction in producing L-C locks which are an essential feature in current work hardening theories and because there exist no data giving direct quantitative values for the density of locks, and because there has even been some doubt expressed as to whether this important reaction occurs at all, a study of the dynamic behavior of the mixed dislocations which form the Lomer lock was undertaken. Due to their ability to cross-slip with relative ease, screw dislocations play an important role in the deformation of fee crystals. For this reason, the second type of reaction considered here is between screw dislocations of opposite sign. In addition, computations in volving screw dislocation interactions are relatively simple, thus providing a convenient check on the cornputational scheme employed. DEFINITION OF PROBLEM The force exerted on a dislocation due to a generalized stress field is given by the Peach and Koehler9 equation: Here t2 and b2 are respectively the tangent and Burgers vectors of the dislocation, and T1 is the stress dyadic defining the local stress field. The stress field may be externally applied or generated internally by the presence of a lattice defect, such as a second dislocation, as is the case in this work. Frank10 has shown that an equivalent momentum, P, of a screw dislocation can be defined by: Here, EST is the total energy of a screw dislocation and ESo is its rest energy. The left side of Eq. [2] is the time derivative of momentum and the right side is the position derivative of the energy due to the dynamical nature of the dislocation. The total energy of a dislocation is the sum of the potential and kinetic energies. Weertman11 has developed the expressions which were used here; these give the potential and kinetic energies of uniformly moving edge and screw dislocations in an isotropic medium.

Jan 1, 1969

By H. K. Work, G. H. Enzian

In the manufacture of steel for commercial purposes, the deoxidation practice used, i.e., the method and degree of deoxidation, is an important factor affecting the structure and mechanical properties of the finished steel. Deoxidation practice exerts a pronounced influence not only on the soundness of the ingots but also on the reaction of the steel to a number of mechanical and thermal treatments. The first mentioned effect of deoxidation is more or less obvious and was first demonstrated, though perhaps not fully appreciated, by Robert Mushet when, in 1856, he added speigeleisen to low-carbon bessemer blown metal. In 1861. Bessemer patented the addition of one pound per ton of silicon to his blown metal to "cause the metal to lie quietly in the mold." The second effect of deoxidation-—that is, the effect on the properties and behavior of the steel—is, one might say, more subtle, and certainly not as well understood as the first, although in many cases it is the more important consideration. This paper is limited to a discussion of only the second effect of deoxidation and: in particular, to the effect on the strain-sensitivity of low-carbon steels. General Discussion Originally it was thought that the function of a deoxidizer was to combine with the oxygen present in the steel as iron oxide and prevent its subsequent evolution as a gas. -More recently it has been realized that a deoxidizer does more than this. Frequent reference has been made to the effect of deoxidizers on the nitrogen in the steel, and some attention has also been paid to hydrogen. As a consequence of the above situation any study of deoxidation must be concerned with the gas content of the steel and the effect of the deoxidizer on the gases involved. The term "gas content" as used here refers to gases extracted from steel during melting in vacuum rather than to elements present in steel in the gaseous state. The extracted gases, at least in the case of oxygen and nitrogen, are generally accepted to be products of decomposition of oxides, nitrides, or other more complex compounds. The manner in which deoxidation affects the gas content of steel and the significance of gases in steel have been and still are subjects of considerable speculation. No attempt will be made here to give a complete discussion of the literature on this subject but a few references will be cited for purposes of illustration. N. Hamilton1 found a correlation between the oxygen content of alloy steel and the behavior of the steel during tube piercing. Davenport, Bain, and others associated oxygen with aging properties of steel while Köster5 and a number of others6-lo made similar claims for nitrogen. Daniloff, Mehl, and Hertyll stated that "deoxidation decreases the susceptibility of steels to aging directly

Jan 1, 1945

US 4,185,078-In the recovery of rhenium values from an aqueous sodium molybdate solution contained in the hydrometallurgical processing of roasted molybdenite, improved results are realized by using a described extractant consisting of a quaternary ammonium compound and benzene or other highly aromatic solvent which dissolves a quaternary ammonium-rhenium complex Essentially all rhenium is recovered from the solution and the extractant can be regenerated and recycled. This patent is a continuation-in-part of US Patent No. 4,049,771, dated Sept. 20, 1977. L R. Quatrini and M.B MacInnis, assigned to GTE Sylvania Inc. Jan 22, 1980. 6 pp (423-49). Flied. 7-19-78 (926,167).

Jan 1, 1982

By H. H

This paper describes the milling practice and operating results of the recently installed heavy-media separation plant of Barton Mines Corporation, the world's largest producer of garnet. This pioneer application of heavy-media separation (sink-float) processes for the beneficiation of a nonmetallic ore is unique in many respects, the details of which will be apparent from the following presentation. Characteristics of the Ore The property is on Gore Mountain, 5 miles west of the village of North Creek, New York, and 11 miles by road. The altitude of the mine is approximately 2800 feet. The valuable mineral, garnet, occurs in a surface deposit, the ore body being about ¾, mile long and varying in width from 50 to 300 ft. The garnet, principally almandite, Fe3Al2 (SiO4)3, occurs in a metamorphic rock of uncertain origin. The gangue mineral is principally hornblende, which constitutes from 40 to 80 per cent of the rock. The remainder of the gangue is divided between plagioclase feldspars and hypersthene, with smaller amounts of biotite, apatite and pyrite. The garnet content of the ore body varies from 5 to 20 per cent of the mass and averages about 10 to I2 per cent. The garnet occurs as crystals, mostly imperfectly developed, known locally as "pockets." These crys- tals vary in size from a fraction of an inch to a foot or more in diameter. Occasionally crystals have been found up to 30 and 36 in. in diameter but they average 4 to 6 inches. Nearly every crystal of garnet is surrounded by a rim of coarsely crystalline hornblende. The quarry faces are striking in appearance, showing crimson-red garnet crystals with their coal black rims scattered over a grayish black background. The specific gravity of the garnet is 3.8 to 4.1 while that of the hornblende ordinarily is 3-07 to 3.24. Some specimens of very dense hornblende have been found with a specific gravity as high as 3.40. The garnet crystals are laminated in structure, and readily cleave into flat, tabular pieces with sharp, chisel-like edges. Even when crushed to a very fine size, the garnet retains this flat, sharp, slivery grain shape. This characteristic, together with its hardness and toughness, gives it its value as an abrasive- Former Operations Mining operations have been carried on for 60 years. Until 1923, only the oxidized (soft rock) section of the ore body was mined. The oxidation, which affected the garnet only slightly, made possible the removal of the garnet from the rock by hand after it was blasted down, using small hand picks. In 1923 a mill was erected on the property, and was rebuilt and redesigned in 1928. Before the adoption of heavy-media separation, concentration was effected by

Jan 1, 1943

By H. H

This paper describes the milling practice and operating results of the recently installed heavy-media separation plant of Barton Mines Corporation, the world's largest producer of garnet. This pioneer application of heavy-media separation (sink-float) processes for the beneficiation of a nonmetallic ore is unique in many respects, the details of which will be apparent from the following presentation. Characteristics of the Ore The property is on Gore Mountain, 5 miles west of the village of North Creek, New York, and 11 miles by road. The altitude of the mine is approximately 2800 feet. The valuable mineral, garnet, occurs in a surface deposit, the ore body being about ¾, mile long and varying in width from 50 to 300 ft. The garnet, principally almandite, Fe3Al2 (SiO4)3, occurs in a metamorphic rock of uncertain origin. The gangue mineral is principally hornblende, which constitutes from 40 to 80 per cent of the rock. The remainder of the gangue is divided between plagioclase feldspars and hypersthene, with smaller amounts of biotite, apatite and pyrite. The garnet content of the ore body varies from 5 to 20 per cent of the mass and averages about 10 to I2 per cent. The garnet occurs as crystals, mostly imperfectly developed, known locally as "pockets." These crys- tals vary in size from a fraction of an inch to a foot or more in diameter. Occasionally crystals have been found up to 30 and 36 in. in diameter but they average 4 to 6 inches. Nearly every crystal of garnet is surrounded by a rim of coarsely crystalline hornblende. The quarry faces are striking in appearance, showing crimson-red garnet crystals with their coal black rims scattered over a grayish black background. The specific gravity of the garnet is 3.8 to 4.1 while that of the hornblende ordinarily is 3-07 to 3.24. Some specimens of very dense hornblende have been found with a specific gravity as high as 3.40. The garnet crystals are laminated in structure, and readily cleave into flat, tabular pieces with sharp, chisel-like edges. Even when crushed to a very fine size, the garnet retains this flat, sharp, slivery grain shape. This characteristic, together with its hardness and toughness, gives it its value as an abrasive- Former Operations Mining operations have been carried on for 60 years. Until 1923, only the oxidized (soft rock) section of the ore body was mined. The oxidation, which affected the garnet only slightly, made possible the removal of the garnet from the rock by hand after it was blasted down, using small hand picks. In 1923 a mill was erected on the property, and was rebuilt and redesigned in 1928. Before the adoption of heavy-media separation, concentration was effected by

Jan 1, 1943

The Institute maintains a dual relationship with students: (1) an individual relationship with a Student Associate; and (2) a relationship with local organizations of students, known as Affiliated Student Societies or Student Chapters. 1. The conditions of Student Associateship are set forth in Section 9, Article I, of the Bylaws of the Institute (see page 64 and following pages). During 1934, sundry amendments were made for the purpose of improving the student relationship. Postgraduate students are now eligible; and associateship can be maintained, with the payment of the regular dues of $2 per year, for 18 months following graduation in June. With his regular dues, each Student Associate is entitled to receive during the year his choice of MINING AND METALLURGY, METALS TECHNOLOGY, MINING TECHNOLOGY, PETROLEUM TECHNOLOGY, or two "classes" of Technical

Jan 1, 1943

Jan 1, 1900